Breville the 3X Bluicer Pro Manuel utilisateur

Marque: Breville

Modèle: the 3X Bluicer Pro

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Instruction Book - BJB815

the 3X Bluicer Pro

™

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition, we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• Before using the ﬁrst time

ensure your electricity supply

is the same as shown on the

label on the underside of the

appliance. This appliance is

equipped with a power cord

having a grounding wire with a

grounding plug. The appliance

must be grounded using a

properly grounded outlet.

In the event of an electrical

fault, grounding reduces the

risk of electrical shock.

• Do not, under any

circumstances, cut or

remove the third (ground)

prong from the power

cord or use an adapter.

• Consult a qualiﬁed electrician if

the grounding instructions are

not completely understood, or

if doubt exists as to whether the

appliance is properly grounded.

2 Breville Recommends

Safety First

7 Components

8 Assembly

11 Functions

14 Care & Cleaning

16 Troubleshooting

Contents

• The installation of a residual

current safety switch is

recommended to provide

additional safety when using

all electrical appliances.

Safety switches with a rated

operating current not more

than 30mA are recommended.

Consult an electrician for

professional advice.

• Remove and discard

any packaging materials

safely, before ﬁrst use.

• To eliminate a choking hazard

for young children, discard

the protective cover ﬁtted

to the power plug safely.

• Always ensure the appliance

is properly assembled, as per

instructions, before use. Using

the appliance without being

properly assembled may cause

product malfunction, product

damage or pose safety risk

including personal injury.

• This appliance is for household

use only. Do not use the

appliance for anything other

than its intended purpose. Do

not use in moving vehicles or

boats. Do not use outdoors.

Misuse may cause injury.

• Position the appliance on a

stable, heat resistant, level, dry

surface away from the counter

edge, and do not operate on

or near a heat source such as

a hot plate, oven or gas hob.

• Fully unwind the power

cord before operating.

• Do not let the power cord

hang over the edge of a

counter or table. Do not let

the power cord touch hot

surfaces or become knotted.

• Do not leave the appliance

unattended when in use.

• If the appliance is to be left

unattended, cleaned, moved,

assembled or stored, always

switch off the appliance by

pressing the ON | OFF button

to OFF. Unplug from the power

outlet. To unplug, grasp the

plug and pull from the outlet.

Never pull from the power cord.

• Turn the appliance OFF, then

unplug from the outlet when

not in use, before assembling or

disassembling parts and before

cleaning. To unplug, grasp the

plug and pull from the outlet.

Never pull from the power cord.

• Regularly inspect the power cord,

plug and actual appliance for any

damage. If found to be damaged

in any way, immediately cease

use of the appliance and return

the entire appliance to the

nearest authorized Breville

Service Center for examination,

replacement or repair.

• Keep the appliance and

accessories clean. Follow

the cleaning instructions

provided in this book. Any

procedure not listed in this

instruction booklet should be

performed at an authorized

Breville Service Center.

• This appliance is not intended

for use by children or by persons

with reduced physical, sensory,

or mental capabilities, or lack

of experience and knowledge.

Close supervision is necessary

when any appliance is used near

children. Children should be

supervised to ensure that they

do not play with the appliance.

• Children should not play

with the appliance.

• Cleaning of the appliance should

not be carried out by children.

• The appliance power cord, and

any components, attachments

or accessories should be

kept out of reach of children

aged 8 years and younger.

• Never use attachments or

accessories that are not supplied

with this product or authorised

by Breville to be used on this

product. Failing to follow this

instruction may cause product

malfunction, product damage,

ﬁre, electric shock or injury.

• Do not attempt to operate

the appliance by any

method other than those

described in this booklet.

• Do not move the appliance

while in operation.

• Do not operate the appliance

on an inclined surface.

• Flashing light indicates ready

to operate. Avoid any contact

with blades or moveable parts.

• Do not put your ﬁngers or other

objects into the juicer opening

while it is in operation. If food

becomes lodged in opening, use

food pusher or another piece

of fruit or vegetable to push

it down. When this method is

not possible turn the motor

off and disassemble juicer to

remove the remaining food.

• Do not juice stone fruit

like peach, plum or cherry

unless seeds and/or stones

have been removed.

• Make sure the product is

turned OFF and the

stainless-steel ﬁlter basket

has stopped rotating and the

motor has completely stopped

before releasing the safety

locking arm and/or attempting

to move the appliance,

when the unit is not in use,

and before disassembling,

cleaning and storing.

• Any signiﬁcant spillage onto

the surface under or around

the appliance, or onto the

appliance itself, should be

cleaned and dried before

continuing to use the appliance.

• Be careful when handling the

stainless-steel ﬁlter basket as the

small cutting blades at the base

of the ﬁlter basket are very sharp.

Mishandling may cause injury.

• Blender blades are sharp, take

care when handling, emptying

and cleaning the blender jug.

• Remove rind from all citrus

fruit before juicing.

• Do not use the appliance

if the rotating sieve (ﬁlter

basket) or lid is damaged.

• Always make sure juicer cover

is clamped securely in place

before motor is turned on.

• Do not operate without the

pulp container in place.

• Do not unfasten interlock arm

while unit is in operation.

• Do not juice more than 6.5

pounds (3kg) of carrot at a time.

• Avoid putting the blender

jug on the motor base while

the motor is still spinning.

• Do not operate if the

jug is empty.

• Never attempt to operate

with damaged blades, or

with utensils, or any foreign

objects inside the jug.

• Keep hands and utensils out

of container while blending

to reduce the risk of severe

injury to persons or damage

to the blender. A scraper

may be used but only when

the unit is powered off.

• Do not put the jug in extremes

of heat or cold, for example

placing a cold jug into hot

water, or vice versa.

• Lid must be ﬁrmly secured

to the jug before operation to

ensure internal contents do

not escape, spray or overﬂow.

• Do not remove the jug

from the motor base while

blender is in use.

• Do not use blender while

OVERLOAD PROTECTION

is ﬂashing on the LCD. If this

occurs, unplug the blender

and wait for 30 minutes until

the motor has cooled. Once

cooled, you will be able to use

the blender as usual again.

• Do not process hot or boiling

liquids. Allow to cool before

placing into the blender jug.

• To protect against electric

shock, do not immerse the

power plug, cord or appliance

in water or any liquid.

• Authorized Breville Service

Centers can be found on our

website www.Breville.com

• The appliance power rating is

based on the attachment that

draws the maximum power,

other attachments may draw

signiﬁcantly less power.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

Components

A. Food pusher (not dishwasher safe)

B. Juicer cover (dishwasher safe)

C. Stainless steel ﬁlter basket (dishwasher safe)

D. Filter bowl surround (dishwasher safe)

E. Interlocking safety arm

Stops motor base operating without

cover locked into place.

F. Control panel

G. Stainless steel motor base

H. Inner measuring cup (dishwasher safe)

I. 50 ﬂoz (1.5L) blending jug & lid (dishwasher

safe)

J. Juicing nozzle (dishwasher safe)

Can be placed over spout to juice

directly into a cup.

K. Drip stop plug

L. Pulp container (dishwasher safe)

M. Cleaning brush

For use on Stainless Steel Filter Basket.

Assembly

BEFORE FIRST USE

Wash the lid, inner measuring cup, jug, the

ﬁlter bowl surround, ﬁlter basket, juicer

cover, food pusher and pulp container in

warm, soapy water with a soft cloth. Rinse

and dry thoroughly.

Place motor base on a ﬂat, dry surface such

as a countertop. Ensure that the appliance is

switched to OFF at the motor base and the

power cord is unplugged.

JUICING

1. Place ﬁlter bowl surround on

top of the motor base.

2. Align the arrows at the base of the

stainless-steel ﬁlter basket with the arrows

on the motor drive coupling and push down

until it clicks into place to create a secure ﬁt

with the motor base.

3. Place the juicer cover over the ﬁlter bowl

surround, positioning the lower part of the

feed chute over the stainless steel ﬁlter

basket.

4. Raise the safety locking arm up and locate

into the two grooves on either side of the

juicer cover.

5. The safety locking arm should now be in a

vertical position and locked into place on

top of the juicer cover.

6. Slide the food pusher down the food chute

by aligning the groove in the food pusher,

with the small protrusion on the inside of

the top of the feed tube.

Food

pusher

groove

Small

protrusion

inside

feed tube

7. Place the pulp container into position by

tilting and lifting the motor base slightly.

Insert the pulp container under the juicer

cover on the back ensuring the front edge

is tucked under the back lip of the ﬁlter

bowl surround and the bottom edge is

clipped into the bottom of the motor base.

8. The drip stop plug can be ﬁtted over juice

outlet nozzle. It then allows the outlet to

be plugged to prevent dripping

after juicing.

9. Fit the lid to the blender jug and position jug

under juice spout.

10. Optional: For juicing into a cup the

Juicing Nozzle can be ﬁtted onto the

juice outlet nozzle.

BLENDING

1. With the blender jug in the upright position

place it on the motor base. The handle

of the blender can be positioned to the

left or right-hand side of the appliance.

2. Raise the safety locking arm up

and locate into the two grooves

on either side of the blender.

3. Add food or liquid into the blender jug

ensuring not to exceed the ‘MAX’ line.

Place the blender lid ﬁrmly into position on

the top of the blender jug. Insert the clear,

inner measuring lid into the blender lid and

turn clockwise to lock into position. The jug

features a Breville

Assist™ Lid. This allows

the lid to ﬁt tightly onto the blender jug,

avoiding displacement during operation.

4. Ensure the spout cover of the blender lid

is clipped into place and closed. The ring

pull design allows the user to easily remove

the lid with a simple leverage action.

After appliance is assembled into blender or

juicer conﬁguration, plug power cord into a

120V power outlet.

Press the ON | OFF button to turn the

appliance on. The ON | OFF button will

illuminate. The LCD timer screen will

illuminate with ‘0:00’ displayed.

Functions

GETTING STARTED

The ON | OFF button powers the unit into

READY mode (red light blinking).

PRESET PROGRAMS

BLENDING

The appliance has 5 preset functions:

GREEN SMOOTHIE, SMOOTHIE , PULSE/

ICE CRUSH, AUTO CLEAN and FROZEN

COCKTAIL. These pre-programmed cycles

automatically adjust the blending time and

speeds to optimize blending results. These

programs are only activated when your

appliance is in blender set up. They can't

be used when your appliance is set up in

juicing conﬁguration.

Select the required function by pressing the

corresponding function button. The unit will

start to operate, and the selected function

button will illuminate. The timer will

start to count down and program will end

automatically when it reaches '0:00'.

The program and timer can be paused

by pressing the pause button. Resume by

pressing program button again, or cancel by

pressing pause again.

The program can also be canceled at any

time by pressing the ON|OFF button.

Turning the speed dial will interrupt the

program, placing the blender in manual

mode starting from Speed 1.

GREEN SMOOTHIE

For blending whole fruits/vegetables into

a smooth beverage. A combination of high-

speed proﬁles breaks down tough ﬁbers into

very ﬁne particles.

SMOOTHIE

For dairy-based smoothies a combination of

speeds and pulses are designed to combine

and aerate ingredients into a smooth and

creamy texture.

PULSE / ICE CRUSH

A program of continuous pulsing designed

to chop food into an even consistency or

crush ice cubes. Use the PULSE button when

the food that is being processed is too thick

or coarse to circulate within the blender jug.

The maximum amount of ice cubes the

blender can blend without liquid in the jug

at any one time is 10 standard ice cubes or

approx. 10 ounces (280g).

AUTO CLEAN

Use to remove most of the ingredients off

the blender walls and blades. Add 2 cups

(16 ounces) warm soapy water and press

the AUTO CLEAN button. For harder to

clean, sticky or thick ingredients, add ½

teaspoon of dish soap for extra cleaning

power. For best results, clean the blender

jug immediately after use. The Auto Clean

function only cleans the blender jug. It

doesn't clean the juicer.

FROZEN COCKTAIL

For creating ice-based cocktails and drinks

like Margaritas, Daiquiris and Slushies. An

ice crush program followed by a short blend.

MANUAL OPERATION

Speed Control Dial

BLENDING

Turn the Speed Control Dial clockwise to

select one of 10 speed settings from a slow

STIR (Speed Setting 1) through to a very fast

PULVERIZE (Speed Setting 10). The timer

will start to count up, and blending will stop

when it reaches '1:00'.

Blending can be paused by pressing pause

button. Press pause button again to cancel,

or turn dial to resume blending from

Speed 1.

To stop blending, turn the Speed Control

Dial counterclockwise back to READY or

press ON|OFF button.

COMPATIBLE WITH THE VAC Q™

The 3X Bluicer Pro is compatible with the

Vac Q vacuum pump. The Vac Q improves

texture, colors and ﬂavors for some of

your blended mixes. For certain recipes

ﬂavors will be greatly enhanced providing

smoother green smoothies, creamier

spreads, delicate dips and silkier gazpacho

soup. For milk based shakes, it's the air that's

whipped through and trapped into the shake

that gives that light and bubbly texture. The

Vac Q is sold separately.

JUICING

Wash your selection of fruit and vegetables

to be juiced. Most fruit and vegetables such

as apples, carrots and cucumbers will not

need to be cut or trimmed to size as these

will ﬁt whole into the feed chute. Ensure

vegetables such as beets, carrots etc. have

all soil removed, are washed well and

trimmed of leaves before using.

1. Plug the power cord into your

120V power outlet.

IMPORTANT

Do not load feed chute with produce before

the Juicer has reached the selected speed.

Turning the Juicer On

2. Turn dial to desired speed setting. Use lower

numbers (1–5) for soft fruits and vegetables

and higher numbers (6–10) for hard fruits

and vegetables. See Speed Selector Guide

table on the next page to match speed and

produce type for maximum yield. "Low"

range, while it may not maximize yield

of some produce, allows you to extract

juice at a signiﬁcantly lower noise level.

3. With the motor running, place food into

the feed chute and use the food pusher

to gently guide food down. To extract

the maximum amount of juice, always

push the food pusher down slowly.

4. Full Blender Jug

You can keep juicing until the jug is ﬁlled to

MAX. line.

WARNING

Never use ﬁngers, hands or utensils to push

food down the feed chute or to clear the feed

chute. Always use the food pusher provided.

CAUTION:

sharp blades

The stainless steel ﬁlter basket contains

small sharp blades to cut and process fruit

and vegetables. Avoid touching the blades

when handling the ﬁlter basket.

SPEED SELECTOR GUIDE

FOOD TYPE SPEED

APPLES 10

BABY SPINACH 9

BEETROOT 10

BLUEBERRIES 5

BROCCOLI 7

CABBAGE 9

BELL PEPPER 9

CARROT 10

CELERY 4

CITRUS FRUITS (peeled) 1

CUCUMBER 4

GINGER 8

GRAPES (seedless) 2

HONEYDEW MELON (peeled) 3

KALE 9

KIWI (peeled) 5

MANGO (peeled, pit removed) 5

MINT 9

PEACH (pit removed) 5

PEARS 6

PINEAPPLE (peeled) 7

RHUBARB 8

SQUASH 9

STRAWBERRIES 4

TOMATOES 4

WATERMELON (peeled) 3

ZUCCHINI 6

Care & Cleaning

Ensure the motor base is turned off by pressing

the ON | OFF button. Then unplug the power

cord.

PULP CONTAINER

To minimize cleaning, you can line the pulp

container with a biodegradable bag to collect

the pulp.

MOTOR BASE

Wipe down with a soft damp cloth. Do not

immerse the motor base in liquids.

CLEANING

1. Remove Blender Jug.

2. Disengage Locking Bar, pull up entire Juice

Collector Assembly and take to sink.

3. Remove Pulp Container.

Empty as much pulp as possible into bin/

compost. Rinse all parts after use (except the

motor base) under running water to clear away

the majority of juice and pulp. Wash in warm

soapy water with a soft cloth.

To avoid food drying on to the blades, mesh or

transparent parts, rinse and wash as soon as

possible after use.

JUG AND LID

In order to keep your jug clean and avoid food

drying on the blades and jug, follow the below

steps as soon as possible after use.

Rinse most of the ingredients off the jug and lid.

Fill the jug with 2 cups (16 ounces) of warm

water, ﬁt the lid and press the AUTO CLEAN

button. If thick or sticky ingredients require

extra cleaning power add 1/2 teaspoon dishsoap

with 2 cups (16 ounces) of warm water.

Rinse the jug and lid again and/or wash

separately in warm soapy water with a soft cloth

or bottle brush.

It is most effective to clean the jug immediately

after use.

FILTER BASKET

To ensure consistent juicing results,

always clean the ﬁlter basket thoroughly

immediately after use, using the included

brush.

If pulp is left to dry, it may clog the ﬁne

pores of the ﬁlter mesh, which can affect

juicing performance. The ﬁlter basket can be

soaked in hot soapy water for 10 minutes,

if necessary.

DISHWASHER

All parts except for the motor base and food

pusher are dishwasher safe. The blender

jug can be placed on the bottom shelf of

the dishwasher while the lid and inner

measuring cup should be washed on the

top shelf only. However, washing parts on a

regular basis in the dishwasher can shorten

the life of them due to prolonged exposure

to harsh detergents, hot water and pressure.

Cleaning the parts in the dishwasher also

may cause parts to deteriorate so inspect the

parts regularly and stop using the product if

any signs of damage is noticed.

CLEANING AGENTS

Do not use abrasive scouring pads or

cleaners on either the motor base or the jug,

as they may scratch the surface. Use only

warm soapy water with a soft cloth.

STUBBORN FOOD STAINS

Strong smelling foods such as garlic, ﬁsh

and some vegetables such as carrots may

leave an odor or stain on the blender jug and

lid. To remove, soak blender jug and lid for

5 minutes in warm soapy water. Then wash

with a mild detergent and warm water, rinse

well and dry thoroughly. Store jug with the

lid off.

STORAGE

Store the appliance upright with the blender

jug assembled on the motor base, or beside

it. Do not place anything on top. To allow air

to circulate, keep the lid off.

WARNING

Oils in citrus rind can damage the material

of your blender jug if exposed to it for a

longer period. Always clean your blender jug

immediately after processing citrus rind.

Troubleshooting

LCD screen turns on

but appliance doesn't

respond to controls.

•

The safety locking arm may not be correctly engaged in the vertical operating

position. In this case, the LCD screen will show an animated prompt

Check the top cover is properly aligned and the locking arm is located ﬁrmly

into the two grooves on either side of the juicer cover or blender jug.

All control panel lights

ﬂash and Overload

Protection displayed

on LCD screen

•

This indicates motor overload protection is activated due to motor

overheating or stalling.

•

To reset the protector, unplug from the power supply, then plug back in and

turn on.

•

If Overload Protection is still displayed, unplug the appliance and leave to

cool for at least 30 minutes, then try again. The appliance must be unplugged

while cooling in order to reset properly.

•

If the issue persists after allowing to cool, this indicates an internal problem.

Please call Breville Customer Service or your nearest Authorized Breville

Service Center.

•

Note that triggering the overload protection indicates abnormal use of

the appliance, such as too much load in the blender jug, excessive push

force when juicing or extended continuous use. Please take note of the

conditions and refer to all of the information in these instructions to avoid this

occurrence and extend the life of the appliance.

BLENDING

Food is unevenly

chopped

•

This can happen when too much food is being added at one time.

Try a smaller amount, and work in batches if necessary.

Food is chopped too

ﬁne or is watery

•

Try blending for shorter period of time. Use the PULSE function for

better control.

JUICING

Excess pulp building

up in the stainless-

steel ﬁlter basket

•

Turn the appliance off. Disassemble to scoop excess pulp off the juicer cover.

•

Reassemble and continue juicing. Alternating soft and hard ingredients may

help avoid this.

Pulp too wet and

reduced extracted juice

•

The cleaner the ﬁlter, the better the juice yield, and dryer the pulp. Be sure to

thoroughly clean the juicer as soon as possible after each use. Remove the

stainless-steel ﬁlter basket and thoroughly clean mesh walls with a cleaning

brush. Rinse the ﬁlter basket under hot water. If the ﬁne mesh holes are

blocked, soak the basket in a solution of hot water with 10% lemon juice to

unblock the holes or wash in the dishwasher (top shelf). This will remove

excess ﬁber build up which could be inhibiting the ﬂow.

•

Pusher force could reduce yield because it slows the motor down.

Avoid putting pressure on the food pusher when pushing ingredients down

the feed chute.

•

If juicing large amounts of ﬁbrous ingredients like rhubarb and pineapple,

cleaning the ﬁlter basket in between might be required.

Juice leaks between

the ﬁlter bowl surround

and the juicer cover

•

Try a slower juicing speed and push the food pusher down the feed chute

more slowly.

•

Ensure there is no build up in the ﬁlter basket.

Juice sprays out

from spout

•

The juice is being extracted too fast; try a slower juicing speed (if possible)

and push the food pusher down the feed chute more slowly.

Motor appears to

stall during juicing

•

Wet pulp can build up under the juicer cover and stall the appliance if the

appliance is used excessively without cleaning. If this occurs, disassemble and

follow the cleaning instructions to clean the ﬁlter bowl surround, the stainless-

steel ﬁlter basket and the juicer cover.

•

The appliance can also stall if excessive force is used to push produce down

the feed chute. If this occurs, ensure that a gentler pressure is used to push

produce down the chute.

•

Turn on the appliance before putting ingredients in the chute. Pressing

ingredients down before the motor reaches full speed can cause it to stall or

overload.

•

Hard fruit and vegetables will put excess strain onto the motor if a low speed

is selected. Refer to the reference guide to determine the correct speed for the

fruit and vegetables selected for juicing.

Manuel d'instructions - BJB815

the 3X Bluicer Pro

™

BREVILLE VOUS

RECOMMANDE

LA SÉCURITÉ

AVANT TOUT

Chez Breville, la sécurité

occupe une place de choix.

Nous concevons et fabriquons

des produits de consommation

sans jamais perdre de vue la

sécurité de notre précieuse

clientèle. De plus, nous

vous demandons d'être très

vigilant lorsque vous utilisez

un appareil électrique et de

respecter les mesures de

sécurité qui suivent.

MPORTANTES

MESURES DE

SÉCURITÉ

LIRE TOUTES LES

INSTRUCTIONS

AVANT USAGE ET LES

SAUVEGARDER POUR

RÉFÉRENCE FUTURE

• Avant la première utilisation,

assurez-vous que votre

alimentation électrique est

identique à celle indiquée sur

l'étiquette située sous l'appareil.

Cet appareil est équipé d'un

cordon d'alimentation avec

ﬁl et ﬁche reliés à la terre. En

cas de panne électrique, la

mise à la terre réduit le risque

de décharge électrique.

• Ne jamais, en aucun cas,

couper ou retirer la troisième

broche (mise à la terre) du

cordon d'alimentation et ne

pas utiliser d'adaptateur.

• Consultez un électricien

qualiﬁé si les instructions

de mise à la terre ne sont

pas parfaitement comprises

ou si un doute persiste

quant à la mise à la terre

adéquate de l'appareil.

19 Breville vous recommande

la sécurité avant tout

24 Composants

25 Assemblage

28 Fonctions

31 Entretien et nettoyage

33 Guide de dépannage

Table des

matières

• L'installation d'un interrupteur

de sécurité à courant résiduel

est recommandée pour assurer

une sécurité supplémentaire

lors de l'utilisation d'appareils

électriques. Il est recommandé

d'installer un interrupteur de

sécurité à fonctionnement

nominal n'excédant pas

30 mA. Consultez votre

électricien pour des

conseils professionnels.

• Avant d'utiliser l'appareil,

retirez et jetez en lieu sûr tout

le matériel d'emballage.

• Pour éliminer les risques chez

les jeunes enfants, jetez en lieu

sûr l'enveloppe protectrice

recouvrant la ﬁche de sécurité.

• Avant d'utiliser l'appareil,

assurez-vous de bien l'avoir

assemblé selon les instructions.

Si l'appareil est mal assemblé,

cela peut entraîner un

dysfonctionnement, des

dommages matériels, des

blessures ou des risques

pour la sécurité.

• Cet appareil est destiné à un

usage domestique seulement.

Ne l'utilisez pas à d'autres

ﬁns que celles prévues.

Ne l'utilisez pas dans un

véhicule ou un bateau en

mouvement ni à l'extérieur.

Une mauvaise utilisation

peut causer des blessures.

• Placez l'appareil sur une

surface stable, plane et sèche,

résistant à la chaleur et à

distance du bord du comptoir.

Ne faites pas fonctionner

l'appareil sur ou près d'une

source de chaleur telle qu'une

plaque chauffante, un four ou

une table de cuisson à gaz.

• Déroulez complètement le

cordon avant utilisation.

• Ne laissez pas le cordon

d'alimentation pendre

d'un comptoir ou d'une

table, toucher des surfaces

chaudes ou se nouer.

• Ne laissez pas l'appareil

sans surveillance en

cours d'utilisation.

• Si l'appareil doit être laissé sans

surveillance, nettoyé, déplacé,

assemblé ou rangé, éteignez-

le toujours en appuyant sur la

touche MARCHE | ARRÊT.

Débranchez-le de la prise

de courant. Pour ce faire,

saisissez la ﬁche et retirez-la.

Ne tirez jamais sur le cordon.

• Éteignez l'appareil et

débranchez-le de la prise de

courant lorsqu'il n'est pas

utilisé, avant d'assembler

ou de démonter des pièces

et avant de le nettoyer. Pour

le débrancher, saisissez la

ﬁche et retirez-la. Ne tirez

jamais sur le cordon.

La page charge ...

Breville the 3X Bluicer Pro Manuel utilisateur

Marque: Breville

Modèle: the 3X Bluicer Pro

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Breville the 3X Bluicer Pro User manual

Breville the 3X Bluicer Pro Manuel utilisateur

Breville the 3X Bluicer Pro Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents