PowerSmith PGT140 Manuel utilisateur

Marque: PowerSmith

Modèle: PGT140

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

PGT140

40V MAX LITHIUM-ION

STRING TRIMMER/EDGER

Operator's Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE

WARNING: To reduce the risk of injury, user must read and understand this

operator's manual before operating this product.

888-552-8665

TOLL-FREE

HELP LINE:

WWW.POWERSMITHTOOLS.COM

English

CONTENTS---------------------------------------------------------------------------------------2

IMPORTANT SAFETY RULES-------------------------------------------------------------------3-4

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY------------------------------4-5

IMPORTANT BATTERY INFORMATION-------------------------------------------------------------5

SYMBOLS--------------------------------------------------------------------------------------6-7

SPECIFICATIONS---------------------------------------------------------------------------------7

UNPACKING & CONTENTS------------------------------------------------------------------------7

KNOWING YOUR TRIMMER-----------------------------------------------------------------------8

ASSEMBLY AND ADJUSTMENTS---------------------------------------------------------------8-9

OPERATION---------------------------------------------------------------------------------10-11

MAINTENANCE------------------------------------------------------------------------------12-13

TROUBLESHOOTING----------------------------------------------------------------------------13

WARRANTY-------------------------------------------------------------------------------------13

EXPLODED VIEW-------------------------------------------------------------------------------14

PARTS LIST-------------------------------------------------------------------------------------15

TABLE OF CONTENT

English

IMPORTANT SAFETY RULES

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• Leadfromlead-basedpaints.

• Crystallinesilicafrombricksandcementandothermasonryproducts.

• Arsenicandchromiumfromchemicallytreatedlumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks

that are specially designed to ﬁlter out microscopic particles.

WARNING: When using electric gardening appliances, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric shock, and personal injury.

Read all instructions before using this appliance.

• Avoid dangerous environments - do not use appliances in damp or wet locations.

• Don’t use in rain or in damp conditions.

• Keep children away - all people and pets should be kept at a distance from the work area.

• Dress properly - do not wear loose clothing or jewelry. They can be caught in moving parts. Wear protective

clothing; use of work gloves, long pants, a long-sleeved shirt and safety footwear is recommended when working

outdoors. Wear protective hair covering to contain long hair.

• Use safety glasses - always use face or dust mask if the area in which you are working is dusty.

• Use right appliance - do not use appliance for any job except that for which it is intended.

• Do not force appliance - it will do the job better and with less likelihood of a risk of injury at the rate for which

it was designed.

• Do not overreach - keep proper footing and balance at all times.

• Stay alert. Use common sense. Do not operate appliance when you are tired or under the inﬂuence of drugs,

alcohol or medication.

• When not in use, appliances should be stored indoors in dry places out of reach of children.

• Maintain appliance with care. Follow instructions for lubricating and changing accessories. Keep handles dry,

clean, and free from oil and grease.

• Check damaged parts. Before using the appliance, make sure the safety guards are intact. Never use a tool

without its safety guard. Check the alignment of the moving parts, the binding of the moving parts.

• Check for broken or defective parts that can affect the safe operation of your tool. A guard or other part

that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere

in this manual.

• Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one

type of battery pack may create a risk of ﬁre when used with another battery pack.

• Use appliances only with speciﬁcally designated battery packs. Use of any other battery packs

may create a risk of injury and ﬁre.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting

the battery terminals together may cause burns or a ﬁre.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns. (This advice is considered correct for conventional Ni-Mh, Ni-Cd, lead acid and

lithium-ion cell types. If this advice is incorrect for a cell design that differs from these, then the correct advice may

be substituted.)

• Do not use a battery pack or appliance that is damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behavior resulting in ﬁre, explosion or risk of injury.

English

• Do not expose a battery pack or appliance to ﬁre or excessive temperature. Exposure to ﬁre or

temperature above 40°C or low 0°C may cause explosion.

• Follow all charging instructions and do not charge the battery pack or appliance outside of

the temperature range speciﬁed in the instructions. Charging improperly or at temperatures outside of the speciﬁed

range may damage the battery and increase the risk of ﬁre.

• Check the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the machine.

• Keep hands and feet away from cutting area.

• Make sure all guards, straps, deﬂectors and handles are properly and securely attached.

• Use the manufacturer’s replacement spool or string in the cutting head for best results. Do not use any

other cutting attachment, for example, metal wire, rope, or the like. To install any other brand of cutting head to this

string trimmer can result in serious personal injury.

• Never operate unit without the grass deﬂector in place and in good condition,

• Maintain a ﬁrm grip on both handles while trimming. Keep string head below waist level. Never cut

with the string head located over 30 in. or more above the ground.

• Never use blades, ﬂailing devices, wire or rope. Unit is designed for line trimmer use only. Use of any

other accessories or attachments will increase the risk of injure.

• Do not hang unit so that the switch trigger is depressed.

• For household use only.

• Have servicing performed by a qualiﬁed repair person using only identical replacement

parts. This will ensure that the safety of the product is maintained.

• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as

indicated in the instructions for use and care.

WARNING: This machine produces an electromagnetic ﬁeld during operation. This

ﬁeld may under some circumstances interfere with active or passive medical implants. To

reduce the risk of serious or fatal injury, we recommend persons with medical implants

consult their physician and the medical implant manufacturer before operating this machine.

WARNING: There is a risk of burns as the gear housing can become very hot. Use

gloves when working with the trimmer head.

SAVE THESE INSTRUCTIONS

• SavetheseInstructions.This manual contains important safety and operating instructions for your battery

charger.

• BeforeusingthebatteryCharger,read all instructions and cautionary markings on (1) Battery Charger, (2)

Battery, and (3) Product using battery.

• Useonlythechargerwhich accompanied your product or direct replacements as listed in this manual. Do not

substitute any other charger.

• Donotrechargebatteryindamporwetenvironments.Do not expose battery pack to water or rain.

• Donotoperatechargerwithdamagedcordorplug.Replace immediately.

• Donotoperatechargerifithasreceivedasharpblow,been dropped or otherwise damaged in any

way. Take it to a qualiﬁed serviceman.

• Donotdisassemblechargerorbatterypack.Take it to a qualiﬁed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of electric shock or ﬁre.

IMPORTANT SAFETY RULES

IMPORTANT SAFETY INSTRUCTIONS

FORCHARGER&BATTERY

English

• Donotchargebatterypackwhen temperature is below 50° F (10° C) or above 104° F (40° C). Store tool

and battery pack in a location where temperature will not exceed 122° F (50° C). This is important to prevent serious

damage to the battery cells.

• Placechargeronatnon-ammablesurfaceand away from ﬂammable materials when re-charging the

battery pack.

• Toreduceriskofelectricshock,unplug charger from outlet before attempting any maintenance or cleaning.

• Ifoperatingtimehasbecomeexcessivelyshorter,stop operating immediately. It may result in a risk of

overheating, possible burns and even an explosion.

• Batteryleakagemayoccurunder extreme usage or temperature conditions. Avoid contact with skin and eyes.

If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, wash

them out with clear water for at least 10 minutes, and then seek medical attention right away.

• Donotattempttouseastep-uptransformer,an engine generator or DC power receptacle.

• Donotshortthebatterypack.Do not touch the terminal with any conductive material. Avoid storing battery

pack in a container with other metal objects such as nails, coins, etc. Always protect the battery terminals when

battery pack is not used.

• Donotchargebatterypackinsideaboxorcontainerofanykind.The battery must be placed in a

well ventilated area during charging.

• Donotallowanythingtocoverorclogthechargervents.

• Donotincineratethebatterypackeven if it is severely damaged or is completely worn out. The battery

pack can explode in a ﬁre.

• Disconnectchargerfromthepowersourcewhennotinuse.This will reduce the risk to electric

shock or damage to the charger if metal pieces should fall into the opening. It also will help prevent damage to the

charger during a power surge.

• Useonlythefollowingtypeandsizebattery:PLB14025(onlyuseforchargerPC1401).

WARNING: A battery short can cause a large current ﬂow, overheating, possible

burns and even a breakdown.

WARNING: 120voltsarepresentatchargingterminals,donotprobewithconductive

objects. Electric shock or electrocution may result. Do not allow any liquid to get inside

charger. Electric shock may result.

IMPORTANT SAFETY INSTRUCTIONS

FORCHARGER&BATTERY

IMPORTANTBATTERYINFORMATION:

DISPOSINGOFTHEBATTERY

• YourbatteriesareLITHIUM-IONrechargeablebatteries.CertainLocal,StateandFederallaws

prohibit disposal of these batteries in ordinary trash.

• Consultyourlocalwasteauthoritiesforyourdisposal/recyclingoptions.

• MoreinformationregardingbatterydisposalinU.S.andCanadaisavailableat;

http://www.rbrc.org/index.html,orbycalling1-800-822-8837(1-800-8BATTER).

SAVE THESE INSTRUCTIONS

English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME EXPLANATION

V Volts Voltage

A Amperes Current

Hz Herz Frequency (cycles per second)

W Watts Power

.../min.

Per Minute

Revolutions, strokes, surface speed, orbits etc., per

minute

Alternating Current Type of current

Direct Current Type of characteristic of current

Read the Operator’s Manual

To reduce the risk of injury, the user must read and

understand operator’s manual before using this

product

Wear Eye and Ear Protection

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 along with hear-

ing protection when operating this equipment.

Safety Alert Precautions that concern your safety.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Wet Conditions Alert

Do not expose to rain or use in damp locations

English

SYMBOLS

SPECIFICATIONS

Motor ----------------------------- 40V, Brushed

Battery --------------------------- 40V Max, 2.5Ah, Lithium-Ion

No Load Speed ------------------ 8000 RPM

Cutting Diameter ----------------- 12”

Line ------------------------------ .080”, Dual Line, Auto-Feed,

Shaft Type ----------------------- Straight

Charging Time ------------------- 75 minutes

Net Weight ----------------------- 6.55 lbs.

UNPACkINg & CONTENTS

IMPORTANT! Due to modern mass production techniques, it is unlikely the tool is faulty

or that a part is missing. If you ﬁnd anything wrong, do not operate the tool until the parts

have been replaced or the fault has been rectiﬁed. Failure to do so could result in serious

personal injury.

CONTENTS IN PACKAGE

Description Q'TY Description Q'TY

Trimmer 1 Charger (PC1401) 1

Guard 1 Battery Pack (PLB14025) 1

Front Handle 1 Screwdirver 1

Operator's Manual 1

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER

Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates important information not re-

lated to an injury hazard, such as a situation that may result in property

damage.

1. Rear Handle

2. Trigger Switch

3. Lock-Off Button

4. Battery Pack

5. Battery Locking Tab

6. Adjustable Front Handle

7. Shaft

8. Telescoping Shaft Coupler

9. Edger Shift Button

10. Tilt Button

11. Motor Head

12. Guard

13. Garden Guard

14. Edger Wheel

FIG 1

FIG 2

FIG 3

English

kNOWINg YOUR TRIMMER

ASSEMBLY AND ADJUSTMENTS

WARNING: Always be sure that the product is switched off and the battery is

disconnected before adjusting, adding accessories, or checking a function on the tool.

ATTACHING THE GUARD

Fit the guard (2) onto the trimmer head (1), See Fig 2.

Tighten two screws (3) to secure the guard in place. See Fig 3.

FIG 4

FIG 5

FIG 8

FIG 7

FIG 6

English

ASSEMBLY AND ADJUSTMENTS

ATTACHING THE FRONT HANDLE

1. Press two buttons with your ﬁngers and hold as shown in Fig 4.

2. Install the front handle onto the button base as shown in Fig 5.

ADJUSTING THE FRONT HANDLE (FIG 6)

The front handle can be adjusted up and down in 5 positions.

See Fig 6.

To adjust the front handle, press in the buttons (1) on both

sides and hold; adjust the handle up and down to your desired

position; release the buttons.

The handle should be adjusted so that your front arm is straight

when the trimmer is in the working position.

ADJUSTING THE HEIGHT(FIG 7)

Caution:

Adjust the length of trimmer to obtain the working

position before using the trimmer.

To adjust the height of the trimmer, loosen the shaft coupler (1)

by turning it clockwise as shown in Fig 7, move the bottom shaft

(2) up and down to the desired length, tighten the coupler by

turning it counterclockwise.

INSTALLING OR REMOVING THE BATTERY PACK (FIG 8)

IMPORTANT! The battery pack is not fully charged when it is purchased. Before using the product for the

ﬁrst time, charge the battery pack. Make sure to read all safety precautions and follow the instructions in the Charging

Battery section.

WARNING: Always be sure that the

product is switched off before insertion or

removal of the battery pack.

• To install thebattery pack,slide the battery packontothe

bottom of the rear handle all the way until it locks in place

with a click, as shown in FIG 8. Lightly pull on the battery to

ensure it is locked into place and will not accidentally fall out

of the product.

• Toremovethebatterypack,pullthebatterypackawayfrom

the product while depressing the battery locking tab.

FIG 10

FIG 9

English

STARTING AND STOPPING THE TRIMMER

To Start the Trimmer, press the lock-off button and squeeze the trigger switch.

To Stop the Trimmer, release the trigger switch.

Caution: Always allow a few seconds for the cutting line spool to stop rotating after releasing the trigger

switch.Donotinvertthetrimmer/edgerorplaceyourhandsundertheguarduntilthetrimmer/edgerspoolhascome

to a complete stop.

CUTTING LINE AND FEEDING (FIG 9)

This trimmer uses .80" (2mm) diameter dual nylon line. During use, the tips of the cutting lines will become frayed and

worn. You may feed the cutting lines by either Auto-Feed or Manual-Feed.

Caution: Do not bump trimmer on ground in attempt to feed line or for any other purposes.

AutomaticFeedingtheCuttingLine

When initially switching on the trimmer, a small length of line is fed

out. Each time the trimmer is started from the rest the line will advance

about1/4".

You will hear a ‘clattering’ noise when the lines hit the line cutter (1). This

is normal. After a few seconds the line will be cut to the correct length

and the noise will reduce as the motor gains full speed. If the noise of

the line being cut can’t be heard, more line will need to be fed out. To

feed more line, stop the trimmer completely; then restart, allowing the

motor to reach full speed. Repeat above until you hear the line hitting

against the line cutter.

ManuallyFeedingtheCuttingLine

If required, the cutting line can be fed out manually.

1. Turn off the trimmer and remove the battery.

2. Press and release Manual Line Feed Button (3).

3. Gently pull out the line.

4. Repeat the step 2 and 3 until the cutting line is long enough to reach the Line Cutter.

NOTE: If the line extends past the line cutter, too much line has been fed out. If too much line is fed out, remove the

spool cap (3) and turn spool counter-clockwise until the line is at the desired length.

TILTING THE MOTOR HEAD (FIG 10)

The motor head (3) on this trimmer can be tilted in 3 positions. 45° for

using on a ﬂat cutting area, 30° for a sloped cutting area, and 0° for a

hard-to-reach area.

To Tilt the Motor Head:

1. Press the tilt buttons (1) on the both sides of the motor head (3).

2. Tilt the shaft (2) againt the motor head to the desired angle as shown

in Fig 10. A click sound indicates the shaft is locked in one of the

positions.

USING THE TRIMMER

Follow these tips when using the trimmer.

• Hold the trimmer with your right hand on the rear handle and your left hand on the front handle.

• Keep a ﬁrm grip with both hands while in operation.

• Trimmer should be held at a comfortable position with the rear handle about hip height.

OPERATION

FIG 13

DANGERIOUS

CUTTING AREA

BEST CUTTING AREA

DIRECTION OF

ROTATION

FIG 11

FIG 12

English

• Cut tall grass from the top down. This will prevent grass from wrapping around the boom housing and string head

which may cause damage from overheating.

• If grass becomes wrapped around the string head, remove the battery and then remove the grass.

WARNING: Always hold the string trimmer away from the body keeping clearance

between the body and the string trimmer. Any contact with the string trimmer cutting head

while operating can result in serious personal injury.

CUTTING TIPS (FIG 11)

•

Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

• The trimmer cuts when passing the unit from left to right.

This will avoid throwing debris at the operator.

• Avoid cutting in the dangerous area shown in ﬁgure 11.

• Use the tip of the line to do the cutting; do not force string

head into uncut grass.

• Wire and picket fences cause extra line wear, even

breakage. Stone and brick walls, curbs, and wood may

wear line rapidly.

EDGING (FIG 12)

This trimmer can be easily changed to the edger mode.

1. Remove the battery pack

2. Press the edge shift button (1) and hold.

3. Rotate the bottom shaft (2) 180° clockwise.

4. Release the edge shift button.

WARNING: Never stand directly in the

path of the cutting line while edging. Always

stand to the left of the grass deﬂector to avoid

thrown debris, which could result in serious

personal injury.

CHARGING THE BATTERY (FIG 13)

NOTE:

Always Check that the power supply corresponds to the

voltage on the ratings plate.

• Plug the charger (1) into a 120 Volt AC power source. The green light

(3) will illuminate for 5 seconds, then the light will go off if no battery

pack in the charger.

•Slide the battery (2) all the way into the charger until it locks in place

with a click, as shown in FIG 13. The ﬂashing green light indicates

that the battery is charging. A solid green indicates the battery is fully

charged.

• The ﬂashing red light (4) indicates the battery temperature is too high

to be charged. Wait the battery cool down to start the charging.

• The solid red light indicates the battery is damaged and will never be

charged.

• Batteriesmaybecomewarmwhilecharging.Thisisnormal.

• Ifbatteryishotaftercontinuoususeinthetool,allowittocooldowntoroomtemperaturebeforecharging.Thiswill

extend the life of your batteries.

NOTE: It takes approximately 75 minutes to charge up a completely discharged battery.

OPERATION

FIG 15

SPOOL CAP

TABS

SPOOL

SLOTS

FIG 14

EYELET

English

CLEANING

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Donotatanytimeletbrakeuids,gasoline,petroleum-basedproducts,

penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal injury.

Electric tools used on ﬁberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear

and possible premature failure because the ﬁberglass chips and grindings are highly abrasive to bearings, brushes,

commutators, etc. Consequently, we do not recommended using this tool for extended work on these types of materials.

However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air.

LUBRICATION

This product is permanently lubricated at the factory and requires no additional lubrication.

SPOOL REPLACEMENT (FIG 14)

Use only 0.065" round or twisted or 0.080" diameter twisted line. Use original manufacturer’s spool replacement for

best performance.

• Remove the battery pack.

• Push in tabs on both sides of spool cap and remove the

spool cap.

• Remove the spool.

• To install the new spool, make sure the two lines are

captured in the slots opposite each other on the new spool.

• Install the new spool so that the line and slots align with

the eyelets in the line head. Thread the line into the eyelet.

• Pull the line extending from the line head so the line

releases from the slots in the spool.

• Reinstall the spool cap by depressing tabs into slots and

pushing down until spool cap clicks into place.

LINE REPLACEMENT (FIG 15)

•

Remove the battery.

• Remove the spool from the line head.

• Remove any old line remaining on the spool.

• Cut a piece of line approximately 11 ft. long. Use only

0.065" diameter round or twisted or 0.080" diameter

twisted line.

• Hook the center of new nylon cord into the notch in the

center of the spool, with one end of the cord extending

about3-1/8"(80mm)morethantheother.SeeFig15.

• Wind the line around the upper and bottom parts in the

direction as shown on the spool.

• After winding the line, there should be at leas 1/4"

between the wound line and the outside edge of the spool.

• Replace the plastic retainer, spool, and the spool cap.

Refer to Spool Replacement in this manual.

STORING THE TRIMMER

•

Open telescoping boom coupler and set at shortest setting.

• Clean all foreign material from the trimmer.

• Store it in a place that is inaccessible to children.

• Keep away from corrosive agents such as garden chemicals and de-icing salts.

MAINTENANCE

English

WARRANTY

This product is warranted free from defects in material and workmanship for 3 years after date of purchase. This limited

warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered

by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call Toll-Free

Help Line for possible solutions.

THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.

ACCESSORIES INCLUDED IN THIS KIT ARE NOT COVERED BY THE 3 YEAR WARRANTY.

BATTERY INCLUDED IS WARRANTED FOR ONE (1) YEAR AFTER DATE OF PURCHASE.

For questions about this or any other PowerSmith Product,

Please call Toll-Free: 888-552-8665.

Or visit our web site: www.powersmithtools.com

ACCESSORY AND REPLACEMENT PARTS

Replacement Spool Part Number ..................... PASTS180, PASTS180-2

Replacement Spool Cap Part Number ................ZPGT140P38

PROBLEM POSSIBLE CAUSE SOLUTION

Line will not advance when

using the Auto-Feed

Lines are welded to themselves.

Not enough line on spool.

Lines are worn too short.

Lines are tangled on spool.

Lubricate with silicone spray.

Install a new spool or line. Refer to Spool

Replacement in this manual.

Manually pull line- Refer to Manual Feeding

the Cutting Line

Rewind the line-Refer to Line Replacement.

Line wraps around drive

shaft housing and line head.

Cutting tall grass at ground level. Cut tall grass from the top down to prevent

wrapping.

Motor fails to start when

trigger is depressed.

Battery is not secure

Battery is not charged.

To secure the battery pack, make sure the

latches on the top of the battery pack snap

into place.

Charge the battery pack according to the

instructions included with your model.

MAINTENANCE

TROUBLEShOOTINg

English

EXPLODED VIEW

English

PARTS LIST

NO. PART NO. DESCRIPTION QTY NO. PART NO. DESCRIPTION QTY

1 01.01.1402 Screw ST4x16 20 25 J36.0203.0004 Rotating arm spring 2

2 J36.0201.0002 Rear handle housing-right 1 26 J36.0204.0001 Motor housing left 1

3 J36.0201.0012 Magnet ring 1 27 J36.0204.0003 Flower guard 1

4 J36.0201.0004 Trigger switch 1 28 K36.0102.0200 Magnet ring 1

5 J36.0201.0008 Trigger spring 1 29 J36.0204.0202 Motor 1

6 J36.0201.0200 Terminal base 1 30 J36.0204.0201 Motor support 1

7 J36.0201.0007 Micro switch 1 31 01.01.3102 Screw M5x10 2

8 J36.0201.0001 Rear handle housing-left 1 32 J36.0204.0104 Spring 1

9 J36.0201.0006 Controller 1 33 J36.0204.0102 Sliding block 1

10 J36.0201.0102 Lock off button spring 1 34 J36.0204.0301 Metal slug 1

11 J36.0201.0101 Lock off button 1 35 J36.0204.0302 Fan blade 1

12 J36.0201.0005 Lock button 2 36 01.03.0113 Nut M5 1

13 J36.0201.0003 Front handle 1 37 J36.0204.0103 Wire spool 1

14 J36.0201.0009 Front handle spring 1 38 J36.0204.0101 By taking cover 1

15 J36.0202.0003 Aluminum tube 1 39 J36.0205.0001 Guard 1

16 J36.0202.0001 Lock sleeve 1 1 40 01.01.1414 Screw ST4x22 2

17 J36.0202.0002 Telescoping boom coupler 1 41 J36.0204.0002 Motor housing right 1

18 J36.0202.0005 Tube connector 1 42 J36.0203.0003 Rotating arm button 2

19 J36.0202.0004 Aluminum tube 1 43 J36.0203.0002 Rotating arm right housing 1

20 J36.0202.0007 Spring wire 1 44 J36.0205.0003 Edge wheel shaft 1

21 J36.0202.0006 Fixing ring 1 45 J36.0205.0002 Edge wheel 2

22 J36.0203.0006 Edger spring 1 46 J36.0102.0502 Line cutter 1

23 J36.0203.0005 Edger button 1 47 01.01.1513 Screw M4x10 1

24 J36.0203.0001 Rotating arm left housing 1

AVERTISSEMENT : Pour réduire le risque de blessure, l’utilisateur doit lire et

doit comprendre ce manuel de l’opérateur avant de fonctionner cet outil.

CONSERVER CE MANUEL POUR FUTURE RÉFÉRENCE

888-552-8665

LIGNE D’ASSISTANCE

SANS FRAIS:

WWW.POWERSMITHTOOLS.COM

PGT140

COUPE-HERBES/COUPE-BORDURES

30,5 CM (12 PO) 40 V MAX.

AU LITHIUM-ION

Operator's Manual

Français

TABLE DES MATIÈRES--------------------------------------------------------------------------17

CONSIGNES DE SÉCURITÉ IMPORTANTES -------------------------------------------------18-19

CONSIGNES DE SÉCURITÉ IMPORTANTES SUR LE CHARGEUR ET LA BATTERIE------------19-20

RENSEIGNEMENTS IMPORTANTS SUR LA BATTERIE-------------------------------------------20

SYMBOLES----------------------------------------------------------------------------------21-22

CARACTÉRISTIQUES TECHNIQUES -------------------------------------------------------------22

DÉBALLAGE ET CONTENU----------------------------------------------------------------------22

CONNAÎTRE VOTRE TAILLE-HAIE----------------------------------------------------------------23

ASSEMBLAGE ET RÉGLAGES----------------------------------------------------------------23-24

FONCTIONNEMENT--------------------------------------------------------------------------25-26

ENTRETIEN----------------------------------------------------------------------------------27-28

DÉPANNAGE------------------------------------------------------------------------------------28

GARANTIE ------------------------------------------------------------------------------------- 28

VUE ÉCLATÉE ----------------------------------------------------------------------------------29

LISTE DE PIÈCES-------------------------------------------------------------------------------30

TABLE DES MATIÈRES

Français

CONSIgNES DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT: Certaines poussières produites par des appareils électriques

de ponçage, sciage, meulage, perçage et autres travaux de construction contiennent des

produits chimiques connus pour causer cancer, anomalies congénitales et autres atteintes à

la reproduction. Voici quelques exemples de ces produits nocifs :

• Plombdespeinturesauplomb.

• Silicecristallinedesbriquesetdubétonetd’autresmatériauxdeconstruction.

• Arsenicetchromedeboisd’œuvretraitéchimiquement.

Votre risque en cas d’exposition varie, selon la fréquence d’exécution de ce type de tâches. Pour réduire votre

exposition à ces produits : travaillez dans une zone bien ventilée en portant un équipement de sécurité approuvé, tel

que masque à poussières spécialement conçu pour ﬁltrer les particules microscopiques.

AVERTISSEMENT: Lorsquevousutilisezdesappareilsdejardinageélectrique,

vousdeveztoujoursprendredesprécautionsdebasepourréduirelesrisquesd'incendie,

d'électrocutionetdeblessures.Liseztouteslesinstructionsavantd'utilisercetappareil.

• Éviter les environnements dangereux – ne pas utiliser les appareils dans des endroits humides ou mouillés.

• Ne pas utiliser sous la pluie.

• Tenir les enfants à l'écart - les personnes et les animaux domestiques doivent tous être tenus à distance de

la zone de travail.

• Habillez-vous correctement – ne pas porter de vêtements amples ni de bijoux. Ils risquent de se faire

accrocher par les pièces mobiles. Porter des vêtements de protection; il est recommandé de porter des gants

de travail, un pantalon long, une chemise à manches longues et des chaussures de sécurité lorsqu'on travaille à

l'extérieur. Portez un couvre-cheveux protecteur pour contenir les cheveux longs.

• Utilisezdeslunettesdesécurité- utilisez toujours un masque facial ou masque antipoussières si la zone

dans laquelle vous travaillez est poussiéreuse.

• Utiliser l'appareil correctement - ne pas utiliser l'appareil pour un travail autre que celui auquel il est destiné.

• Ne pas forcer l'appareil – il fera mieux le travail et avec moins de risque de blessure au taux pour lequel il a

été conçu.

• N'allezpastroploin - gardez une bonne position et un bon équilibre en tout temps.

• Soyezvigilant. Faites preuve de bon sens. N'utilisez pas l'appareil lorsque vous êtes fatigué ou sous

l'inﬂuence de drogues, d'alcool ou de médicaments.

• Lorsqu'ilsnesontpasutilisés,les appareils doivent être entreposés à l'intérieur dans des endroits secs et

hors de portée des enfants.

• Entretenir l'appareil avec soin. Suivez les instructions relatives à la lubriﬁcation et au remplacement

d’accessoires. Gardez les poignées sèches, propres et exemptes d'huile et de graisse.

• Vériﬁer les pièces endommagées. Avant d'utiliser l'appareil, assurez-vous que les dispositifs de protection

sont intacts. N’utilisez jamais d’outil sans son protecteur. Vériﬁez l'alignement des pièces mobiles, la ﬁxation des

pièces mobiles.

• Vériezsidespiècessontcasséesoudéfectueuses qui risqueraient d’affecter la sécurité d'utilisation

de votre outil. Sauf indication contraire dans le présent manuel, un protecteur ou toute autre pièce endommagée

doivent être réparés ou remplacés par un centre de service agréé.

• Rechargezseulementaveclechargeurprescritparlefabricant. Un chargeur adapté à un type de

bloc-batterie peut créer un risque d'incendie lorsqu'il est utilisé avec un autre bloc-batterie.

• N'utilisezlesappareilsqu'avecdesblocs-batteriesspécialementconçus. L'utilisation de tout

autre bloc-batterie peut créer un risque de blessure ou d'incendie.

• Lorsquelebloc-batterien'estpasutilisé,tenez-le à l’écart des objets métalliques, comme des trombones,

des pièces de monnaie, des clés, des clous, des vis ou d'autres petits objets métalliques risquant d’établir une

connexion d'une borne à l'autre. Le court-circuit des bornes de la batterie peut causer des brûlures ou un incendie.

• Dans des conditions abusives, un liquide risque d’être éjecté de la batterie; évitez tout contact. En cas de

contact accidentel, rincer à grande eau. Si le liquide entre en contact avec les yeux, consulter un médecin. Le liquide

éjecté de la batterie peut causer une irritation ou des brûlures. (Ce conseil est considéré comme correct pour les

cellules de type Ni-Mh, Ni-Cd, plomb-acide et lithium-ion classiques. Si ce conseil est incorrect pour une conception

de cellule qui diffère de celles-ci, alors le conseil correct peut y être substitué.)

Français

• N'utilisezpasdebloc-batterienid’appareilendommagésoumodiés. Les piles endommagées

ou modiﬁées peuvent manifester un comportement imprévisible, ce qui peut entraîner un incendie, une explosion ou

un risque de blessure.

• N'exposez pas un bloc-batterie ou un appareil au feu ni à une température excessive.

L'exposition au feu ou à une température supérieure à 40 °C ou inférieure à 0 °C peut provoquer une explosion.

• Suiveztouteslesinstructionsdechargement et ne chargez pas la pile ou l'appareil en dehors de la

plage de températures prescrite dans les instructions. Un chargement incorrect ou à des températures en dehors de

la plage prescrite peut endommager la batterie et augmente le risque d'incendie.

• Vériezlazonedetravailavantchaqueutilisation. Retirez tous les objets tels que les pierres, le verre

brisé, les clous, le ﬁl de fer ou la ﬁcelle qui pourraient être jetés ou s'emmêler dans la machine.

• Tenirlesmainsetlespiedséloignésdelazonedecoupe.

• S'assurer que tous les protecteurs, sangles, déﬂecteurs et poignées sont correctement et solidement

ﬁxés.

• Utiliser la bobine ou la ﬁcelle de rechange du fabricant dans la tête de coupe pour de

meilleurs résultats. N'utilisez pas d'autres dispositifs de coupe; comme du ﬁl métallique, une corde ou quelque

chose de semblable. L'installation de toute autre marque de tête de coupe sur ce taille-haie à ligne pourrait entraîner

des blessures graves.

• Ne jamais faire fonctionner l'appareil sans que le déﬂecteur d'herbe soit en place et en bon état.

• Maintenir une prise ferme sur les deux poignées lors de la coupe. Gardez la tête de coupe en bas de la taille.

Ne jamais couper quand la tête de coupe est située à plus de 30 po au-dessus du sol.

• N'utilisezjamaisdelames,dedispositifsàéau,deloudecorde. L'appareil est conçu pour la

taille à la ligne seulement. L'utilisation de tout autre accessoire augmentera le risque de blessure.

• Ne pas suspendre l'appareil de façon à ce que la gâchette d’interrupteur soit pressée.

• Pour usage domestique seulement.

• Faites effectuer l'entretien par un réparateur qualiﬁé en n'utilisant que des pièces de rechange

identiques. Cela garantira le maintien de la sécurité du produit.

• Ne pas modiﬁer ni tenter de réparer l'appareil ou la batterie (selon le cas) sauf comme indiqué dans

les instructions d'utilisation et d'entretien

AVERTISSEMENT: Cette machine produit un champ électromagnétique pendant

le fonctionnement. Ce champ peut, dans certaines circonstances, interférer avec les implants

médicaux actifs ou passifs. Pour réduire le risque de blessures graves ou mortelles, nous

recommandons aux personnes portant des implants médicaux de consulter leur médecin et

le fabricant d'implants médicaux avant d'utiliser cette machine

AVERTISSEMENT: Il y a un risque de brûlures, car le carter d'engrenage peut

devenirtrèschaud.Utilisezdesgantslorsquevoustravaillezaveclatêtedecoupe.

CONSERVEZ CES INSTRUCTIONS

• Conserver ces instructions ! Ce manuel contient des instructions de sécurité et d'utilisation importantes

relatives au chargeur de batterie.

• Avant d'utiliser le chargeur de batteries, lire toutes les instructions et les mises en gardes ﬁgurant (1) sur

le chargeur, (2) la batterie et (3) le produit utilisant la batterie.

• Utilisezuniquementlechargeurquiaccompagnevotreproduitou le remplacement direct énumérés

dans ce manuel. Ne substituez aucun autre chargeur.

• Ne pas recharger la batterie en environnement humide ou mouillé. Ne pas exposer la batterie à

l'eau ou à la pluie.

• Ne pas utiliser le chargeur avec cordon endommagé ou la ﬁche. Remplacer immédiatement.

CONSIgNES DE SÉCURITÉ IMPORTANTES

CONSIGNESDESÉCURITÉIMPORTANTESSURLECHARGEURET

LABATTERIE

Français

• Ne pas utiliser le chargeur s’il a reçu un choc violent, s’il est tombé ou s’il a été endommagé de

quelque façon que ce soit. Le conﬁer à un réparateur qualiﬁé.

• Nepasdésassemblezlechargeuroulablocdebatterie

; en conﬁer l’entretien ou la réparation à un

technicien qualiﬁé. Un démontage incorrect peut entraîner un risque de choc électrique ou d'incendie.

• Nepaschargezleblocdebatterie à des température inférieure à 50 degrés F (10 degrés C) ou au-dessus

de 104 degrés F (40 degrés C). Rangez l'outil et le bloc de batterie dans un endroit où la température ne dépasse pas

122 degrés F (50 degrés C). Ceci est important pour prévenir de graves dommages à la batterie.

• Placezlechargeursurunesurfaceplateininammable et à distance de matériaux inﬂammables

quand re-charge le bloc de batterie.

• Aﬁn de réduire le risque de choc électrique,

débrancher le chargeur de la prise secteur avant de tenter

de le nettoyer ou de le réparer.

• Si l’autonomie de l’outil avant recharge est presque nulle, arrêter immédiatement son utilisation.

Toute utilisation prolongée dans un tel cas risque de provoquer une surchauffe, des brûlures, voir même une

explosion.

• Il peut y avoir une fuite de batterie dans des conditions extrêmes d’utilisation ou de

température. Evitez tout contact avec la peau et les yeux. Si le liquide vient en contact avec la peau, lavez

rapidement à l’eau savonneuse. Si le liquide vient en contact avec les yeux, rincez-les à l’eau pendant au moins 10

minuites et sollicitez des soins médicaux.

• Ne pas essayer d'utiliser un transformateur élévateur, un générateur de moteur ou une prise

d'alimentation CC.

• Nepascourt-circuiterlesbornesdelebatterie. Ne pas toucher les bornes avec un matériau conducteur.

Éviter de stocker la bloc de batterie dans un conteneur comprenant d’autres objets métalliques tels que clous, pièces

de monnaie, etc. Toujours protéger les bornes de le batterie lorsque la bloc de batterie n'est pas utilisée.

• Nepaschargezlablocdebatteriedansuneboîteouuncontenantdetoutgenre. La batterie

doit être placé dans un endroit bien aéré pendant le chargement.

• Ne pas couvrir ou obstruer les évents du chargeur avec quoi que ce soit.

• Ne pas incinérer la bloc de batterie, même si elle est gravement endommagée ou complètement usée. La

batterie risque d'exploser à la chaleur.

• Lorsqu’iln’estpasenusage, débrancher le chargeur de l’alimentation secteur. Ceci réduira le risque de choc

électrique ou de dommages au chargeur si des articles en métal venaient à tomber dans l’ouverture. Ceci aidera

également à éviter des dommages au chargeur en cas de saute de tension.

• Utilisezuniquementlespilesdetypeetdetaillesuivantes:PLB14025(utilisezuniquement

lechargeurPC1401).

AVERTISSEMENT: Uncourt-circuitdebatteriepeutprovoqueruneintensitéde

courant importante, une surchauffe, des brûlures éventuelles et même une panne.

AVERTISSEMENT: Latensionauxbornesdechargeestde120V.Nepas

enfoncer d'objets conducteurs. Un choc électrique peut s'ensuivre Ne laisser aucun liquide

pénétrer dans le chargeur. Un choc électrique peut en résulter.

CONSIGNESDESÉCURITÉIMPORTANTESSURLECHARGEURET

LABATTERIE

RENSEIGNEMENTS IMPORTANTS

SURLABATTERIE

• LesbatteriessontdesbatteriesauLITHIUM-ION rechargeables. Certaines

réglementationslocales,provinciales/d'Étatsetfédérales/nationalesinterdisentdejeterces

batteries à la décharge publique courante.

• Consulterlesautoritéslocalescompétentesenmatièredetraitementdesdéchetspour

connaître les options d’élimination ou de recyclage disponibles

• Davantaged’informationsrelativesàl’éliminationdesbatteriesauxÉtats-UnisetauCanada

sontdisponiblesausiteInternetwww.rbrc.org/index.html,ouenappelantle1-800-822-8837

(1-800-8BATTERY)

CONSERVEZ CES INSTRUCTIONS

La page charge ...

PowerSmith PGT140 Manuel utilisateur

Marque: PowerSmith

Modèle: PGT140

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: PowerSmith PGT140 User manual
español: PowerSmith PGT140 Manual de usuario

PowerSmith PGT140 Manuel utilisateur

PowerSmith PGT140 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents