Whirlpool GI15NDXTS0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GI15NDXTS0

Taper: Le manuel du propriétaire

ICEMAKER

_illY:_,_i:!__i!ii_:i_i:ii':!_ii_i_:_'_ili!iif!fill¸!:_i:i,i_!::!ii_:i!!_

For questions about features, operation/performance,

parts, accessories or service, call: 1-800-253-1301.

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6777

or visit our website at...

www.whirlpool.com or www.whirlpoolappliances.ca

MACHINEAGLA(_ONS

Au Canada, pour assistance, composez le 1-800-461-5681, pour

installation ou service, le 1-800-807-6777

ou visitez notre site web &

www.whirlpoolappliances.ca

Table of Contents/Table des matieres .................. 2

2313683A

TABLEOFCONTENTS

ICE MAKER SAFETY ...................................................................... 3

INSTALLATION INSTRUCTIONS .................................................. 3

Unpack the Ice Maker .................................................................. 3

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 4

Water Supply Requirements ........................................................ 4

Leveling ........................................................................................ 5

Connect Water Supply ................................................................. 5

Drain Connection ......................................................................... 6

Ice Maker Door ............................................................................. 7

Normal Sounds ............................................................................ 8

ICE MAKER USE ............................................................................ 8

How Your Ice Maker Works ......................................................... 8

Using the Controls ....................................................................... 9

ICE MAKER CARE .......................................................................... g

Cleaning ........................................................................................ 9

Vacation and Moving Care ......................................................... 11

TROUBLESHOOTING .................................................................. 12

Ice Maker Operation ................................................................... 12

Ice Production ............................................................................ 12

Ice Quality ................................................................................... 13

Plumbing Problems .................................................................... 13

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A................................................................................ 13

In Canada ................................................................................... 13

WAR RANTY .................................................................................. 14

TABLEDESMATIERES

S¢:CURIT¢: DE LA MACHINE A GLAQONS ................................ 15

INSTRUCTIONS D'INSTALLATION ............................................ 15

Deballage de la machine h gla(_ons........................................... 15

Exigences d'emplacement ......................................................... 16

Specifications electriques .......................................................... 16

Specifications de I'alimentation en eau ..................................... 16

Nivellement ................................................................................. 17

Raccordement a la canalisation d'eau ...................................... 17

Raccordement au conduit d'evacuation ................................... 18

Porte de la machine a glagons .................................................. 19

Sons normaux ............................................................................ 20

UTILISATION DE LA MACHINE A GLA(_ONS ............................ 21

Fonctionnement de la machine a gla(_ons................................. 21

Utilisation des commandes ........................................................ 21

ENTRETIEN DE LA MACHINE ._,GLA_ONS .............................. 22

Nettoyage ................................................................................... 22

Precautions h prendre avant les vacances

ou un demenagement ................................................................ 24

DEPANNAGE ................................................................................. 25

Fonctionnement de la machine a gla(_ons................................. 25

Production de gla(_ons............................................................... 25

Qualite des gla(_ons.................................................................... 26

Problemes de plomberie ............................................................ 26

ASSISTANCE OU SERVICE ......................................................... 26

GARANTIE ..................................................................................... 27

ICEMAKERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

Removing Packaging Materials

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice

maker. These products can damage the surface of your ice

maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside

of your ice maker before using it. See the cleaning instructions in

_, ..............................................................................................................................................................................................................................................................................................................................................................................................................................the "Ice Maker Care" section.

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue from the exterior of the

ice maker, rub the area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with your

fingers. Wipe with warm water and dry.

,,_i:¸_c_ilti:ili_:_;_ii__::_iii!_ii_¸_ _/_iii_ii_,_;!!!%ii__:!!_ii:i__i:!i;

To ensure proper ventilation for your ice maker, the front side

must be completely unobstructed. The unit may be closed-in

on the top and three sides, but the installation should allow

the ice maker to be pulled forward for servicing if necessary.

Installation of the ice maker requires a cold water supply inlet

of 1/4"(6.35 mm) OD soft copper tubing with a shutoff valve

and either a gravity-drain system or condensate pump to

carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained

between 70°F (21°C) and 90°F (32°C).

This unit must be installed in an area protected from the

elements, such as wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical

and plumbing fixtures in the recommended location as

shown.

NOTE:

• Be sure the power supply cord is not pinched between

the ice maker and the cabinet.

• Be sure the water supply line is not pinched between the

ice maker and the cabinet.

• Be sure the drain line (on some models) is not pinched

between the ice maker and the cabinet.

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

281/2"

(72.4 cm)

(38,1 cm)

A.Recommended location for electrical

andplumbing fixtures

B.Floor level

You should choose a location where the floor is even. It is

important for the ice maker to be level in order to work

properly. If needed, you can adjust the height of the ice maker

by changing the height of the leveling legs. See "Leveling."

Electricam Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can resumt in death,

fire, or eiectricam shock.

Before you move your ice maker into its final location, it is

important to make sure you have the proper electrical

connection:

A 115 Volt, 60 Hz., AC only 15- or 20- amp electrical supply,

properly grounded in accordance with the National Electrical

Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain.

IMPORTANT: Ifthis product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Ice quality

may be affected. If nuisance tripping has occurred, and if the

condition of the ice appears poor, dispose of it.

Recommended grounding method

For your personal safety, this appliance must be grounded. This

appliance is equipped with a power supply cord having a 3 prong

grounding plug. To minimize possible shock hazard, the cord

must be plugged into a mating, 3 prong, grounding-type wall

receptacle, grounded in accordance with the National Electrical

Code and local codes and ordinances. Ifa mating wall receptacle

is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a

qualified electrician.

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If

you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the ice

maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

The reverse osmosis system must provide 1 gal. (3.79L) of water

per hour to the ice maker for proper ice maker operation.

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allowthestoragetankonthereverseosmosissystemtorefill

afterheavyusage.

Ifyouhavequestionsaboutyourwaterpressure,callalicensed,

qualifiedplumber.

Itisimportantfortheicemakertobelevelinordertowork

properly.Dependinguponwhereyouinstalltheicemaker,you

mayneedtomakeseveraladjustmentstolevelit.Youmayalso

usethelevelinglegstolowertheheightoftheicemakerfor

undercounterinstallations.

Tools needed:

Gather the required tools and parts before starting installation.

• 9" level

• Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another

person to assist you.

1. Move the ice maker to its final location.

NOTE: If this is a built-in installation, move the ice maker as

close as possible to the final location.

2. Place a carpenter's level on top of the product to see if the ice

maker is level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the

leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as

follows:

• Turn the leveling leg to the right to lower that side of the

ice maker.

• Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add

stability when needed.

5. Push up on the top rear of the ice maker and locate the

leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the

legs.

7. Use a carpenter's level to recheck the ice maker to see that it

is even from front to back and side to side. If the ice maker is

not level, repeat steps 2 to 5. Ifthe ice maker is level, go to

the "Connect Water Supply" section.

Read all directions thoroughly before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will

remain above freezing.

Tools needed:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver

• 7/16"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

• 1/4"drill bit

• Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Connecting the water line

Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

Find a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water

pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

3. Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold

water pipe you have selected.

4. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the

water pipe and that the washer is under the pipe clamp.

Tighten packing nut. Tighten the pipe clamp screws carefully

and evenly so washer makes a watertight seal. Do not

overtighten the pipe clamp or you may crush cold water pipe

if it is soft copper tubing. Do not use a piercing-type or 3/16"

(4.76 mm) saddle-type valve which reduces water flow and

clogs more easily.

5. Now you are ready to connect the copper tubing. Use 1/4"

(6.35 mm) OD soft copper tubing for the cold water supply.

• Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

• Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end

squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not overtighten.

............... ,,,,,,,,, C

A.Cold waterpipe E.Compression nut

B.Pipe clamp E Compression sleeve

C.Copper tubing G.Shutoff valve

D.Coupling (purchased) H.Packing nut

Place the free end of the tubing into a container or sink, and

turn on main water supply and flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet which is

located on the back of the ice maker cabinet as shown.

Leave a coil of copper tubing to allow the ice maker to be

pulled out of the cabinet or away from the wall for service.

REAR VIEW

A. Drain hose (drain pump models only)

B. Vent hose (drain pump models only)

C. Water supply line

Thread the nut onto the coupling on the end of the copper

tubing. Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A B C

A.Line to ice maker

B.Nut (purchased)

C.Ferrule (purchased)

D. Coupling (purchased)

D F o

E.Ferrule

F Nut

G.Supplied line from ice maker

g. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

SIDE VIEW

3%"

(9.2 cm)

23" C

(58,4 cm)

2". 11/2''

(5 cm - 3.8 cm)

A. Drain hose

B. 1" (2.54 cm) air gap

C. PVC drain reducer

D. Center of drain should be 23" (58.4 cm) from front of door,

with or without the 3/4"(1.91 cm) panel on the door: The

drain should also be centered from left to right (7 _J'

[18.56 cm] from either side of the ice maker).

Drain Pump System (on some models)

Connect the ice maker drain to your drain in accordance with the

International Plumbing Code and any local codes and

ordinances.

NOTE: If the drain hose becomes twisted and water cannot

drain, your ice maker will not work.

Connecting the Drain

After ensuring that the drain system is adequate, follow these

steps to properly place the ice maker:

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all

state and local codes and ordinances. If the ice maker is

provided with a gravity drain system, follow these guidelines

when installing drain lines. This will help keep water from flowing

back into the ice maker storage bin and potentially flowing onto

the floor causing water damage.

• Drain lines must have a minimum of %" (15.88 mm) inside

diameter.

• Drain lines must have a 1" drop per 48" (2.54 cm drop per

122 cm) of run or 1/4"drop per 12" (6.35 mm per 30.48 cm) of

run and must not have low points where water can settle.

• The floor drains must be large enough to accommodate

drainage from all drains.

The ideal installation has a standpipe with a 11/2"(3.81 cm) to

2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a

1" (2.54 cm) air gap between the drain hose and the

standpipe.

• It may be desirable to insulate the drain line thoroughly up to

the drain inlet.

Electdca_ Shock Hazard

P_ug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrica_ shock,

1. Plug ice maker into a grounded 3 prong outlet.

Reverse Hinges

2. Style 1 - For gravity drain system, push the ice maker into

position so that the ice maker drain tube is positioned over

the PVC drain reducer. See "Gravity Drain System" earlier in

this section. Style 2 - For drain pump system connect the

drain pump outlet hose to the drain. See "Drain Pump

System" earlier in this section.

3. Recheck the ice maker to be sure that it is level. See

"Leveling."

4. If it is required by your local sanitation code, seal the cabinet

to the floor with an approved caulking compound after all

water and electrical connections have been made.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• %6" wrench • Flat putty knife

• 1/4"wrench • Phillips screwdriver

1. Unscrew and remove the top hinge. Replace the screws in

the empty hinge holes.

2. Remove the screws from the bottom of the opposite side of

the ice maker cabinet. Turn the top hinge upside down so

that the hinge pin points up. Place the hinge on the bottom

opposite side of the ice maker and tighten screws.

3. Remove the plastic hinge pin sleeve from the "old" bottom

hinge and replace it on the new bottom hinge pin.

4. Remove the "old" bottom hinge screws and hinge. Replace

the screws in the empty hinge holes.

5. Remove the screws from the top of the opposite side of the

ice maker cabinet. Turn the hinge upside down so that the

hinge pin points down. Place the hinge on the top opposite

side of the ice maker and tighten the screws.

6. Remove the top hinge pin.

Replace Door

1. Place plastic hinge pin sleeve in the top hinge hole on the

door. Align the door with the top hinge hole and replace the

top hinge pin.

2. Replace the handle and handle screws.

Top Hinge

......................................A

Hinge pin

5/16"Hex-head hinge screw

Handlescrew End Capscrew

Remove door

1. Unplug ice maker or disconnect power.

2. Remove the handle screws and handle (on some models).

Keep the parts together and set them aside.

3. Remove the hinge pin from the top hinge.

4. Remove the door from the hinges and screw the top hinge pin

back into the top hinge.

5. Reverse the door endcaps as follows:

• Remove both the screws and endcaps (top and bottom).

• Move the top end cap diagonally to the opposite side's

bottom corner, keeping the straight side of the end cap

facing the front of the ice maker.

• Move the bottom end cap diagonally to the opposite

side's top corner, keeping the straight side of the end cap

facing the front of the ice maker.

6. Set the door aside.

Bottom Hinge

A. Hinge pin

B. Hinge pin sleeve

C. Hinge

D. Hex-head hinge screw

........................................................O

A.Hex-head hinge screw

B. Hingepin sleeve

C. Hinge

D. Hingepin

Reverse Door Catch

1. Remove the hole plugs from the opposite side of the door

and set aside.

2. Remove the screws from the magnetic door catch and

replace it on the opposite side of the door.

3. Push the hole plugs into place on the opposite side of the

door.

E_ectrica_ Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or e_ectrica{ shock.

4. Plug in ice maker or reconnect power.

Your new ice maker may make sounds that are not familiar to

you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces such as floors, walls and cabinets can make the sounds

seem louder than they actually are. The following describes the

kinds of sounds that might be new to you and what may be

making them.

• You will hear a buzzing sound when the water valve opens to

fill the water reservoir for each cycle.

• Rattling noises may come from the flow of the refrigerant or

the water line. Items stored on top of the ice maker can also

make noises.

• The high-efficiency compressor may make a pulsating or high

pitched sound.

• Water running over the evaporator plate may make a

splashing sound.

• Water running from the evaporator plate to the water reservoir

may make a splashing sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your ice maker.

• You may hear air being forced over the condenser by the

condenser fan.

• During the harvest cycle, you may hear a "thud" when the ice

sheet slides from the evaporator onto the cutter grid.

• When you first start the ice maker, you may hear water

running continuously. The ice maker is programmed to run a

rinse cycle before it begins to make ice.

ICEMAKERUSE

When you first start your ice maker, the water pan will fill and the

system will rinse itself before starting to make ice. The rinsing

process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at

preset temperatures. The ice level sensor located in the ice

storage bin will monitor the ice levels.

IMPORTANT:

• If the water supply to the ice maker is turned off, be sure to

set the ice maker control to OFR

• The ice maker is designed to make clear ice from the majority

of water sources on a daily basis. If your results are

unsatisfactory, your water may need to be filtered or treated.

The Ice Making Process

1. Water is constantly circulated over a freezing plate. As the

water freezes into ice, the minerals in the water are rejected.

This produces a sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after

each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

5. Cubes fall into the storage bin. When the bin is full, the ice

maker shuts off automatically and restarts when more ice is

needed. The ice bin is not refrigerated, and some melting will

occur. The amount of melting varies with room temperature.

NOTE: As the room and water temperatures vary, so will the

amount of ice produced and stored. This means that higher

operating temperatures result in reduced ice production.

Ice Maker System

1. To start the normal ice making cycle, select ON.

2. To stop ice maker operation, select OFR

® ® ® ®

ON/ OFF LOCKOUT SERVICE CLEANCYCLE

NOTE:

• Pressing the ON/OFF switch does not shut off power to

the ice maker.

• Allow 24 hours to produce the first batch of ice. Discard

the first batch produced.

Lock Out Mode

The control panel can be turned off for easy cleaning or to

prevent accidental activation by children or small pets.

NOTE: The lock feature does not shut off power to the ice maker

or to the ice maker bin light. It simply deactivates the control

panel.

1. To lock the control panel, press and hold the LOCKOUT

button until the indicator appears.

2. To unlock the control panel, press and hold the LOCKOUT

button until the indicator disappears.

Service Light

The service light indicates when service is needed. If the service

light turns on, turn the ice maker off and back on. If the service

light turns on again, call for service.

Cleaning Needed Status Light

The Cleaning Needed Status light will help you know when it is

time to clean your ice maker. The light will change from green to

yellow. This tells you it is almost time to clean your ice maker. It is

recommended that you clean the ice maker when the status light

changes to red OR ice production decreases significantly. To

clean your ice maker, see "Ice Maker System."

ICEMAKERCARE

The ice making system and the air cooled condenser need to be

cleaned regularly for the ice maker to operate at peak efficiency

and to avoid premature failure of system components. See the

"Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water

and mild soap or detergent. Wipe and dry. Regular use of a good

household appliance cleaner and wax will help protect the finish.

Do not use abrasive cleaners on enamel surfaces as they may

scratch the finish.

For products with a stainless steel exterior, use a clean sponge or

soft cloth and a mild detergent in warm water. Do not use

abrasive or harsh cleaners. Do not use chlorine bleach on

stainless steel surfaces.

Minerals that are removed from water during the freezing cycle

will eventually form a hard scaly deposit in the water system.

Cleaning the system regularly helps remove the mineral scale

buildup. How often you need to clean the system depends upon

how hard your water is. With hard water of 15 to 20 grains/gal.

(4 to 5 grains/liter), you may need to clean the system as often as

every 6 months.

NOTE: Use one 16 oz (473 mL) bottle of approved ice maker

cleaner. To order, call 1-800-442-9991 and ask for Part Number

4396808. In Canada, call 1-800-807-6777.

1. Turn off the ice maker.

2. Wait 5 to 10 minutes for the ice to fall into the storage bin.

Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan

located inside the storage bin as shown. Allow the water to

drain completely.

4. Replace the drain cap securely on the water pan. If the drain

cap is loose, water will empty from the water pan and you will

have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle

before completing the steps below. Use one 16 oz (473 mL)

bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle

twice with tap water and pour it into the water pan.

A. Water pan

B. Water pan thumb screws

C. Drain cap

7. Press and hold the CLEAN button. See "Using the Controls."

The light will blink, indicating that the cleaning cycle is in

process. When the indicator light turns green (approximately

70 minutes), the cleaning cycle is complete. During the

cleaning cycle, the system will both clean and rinse itself.

8. After the cleaning cycle is complete, remove the drain cap

from the water pan. Look for any cleaning solution left in the

water pan. If cleaning solution drains from the water pan, you

should run the clean cycle again. Be sure to replace the drain

cap securely on the water pan. Ifthe drain cap is loose, water

will empty from the water pan and you will have either thin ice

or no ice.

NOTE: Severe scale buildup may require repeated cleaning with

a fresh quantity of cleaning solution.

9. Press and hold the ON button to resume ice production.

Condenser

A dirty or clogged condenser:

• Obstructs proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures

which may lead to component failure.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace aH parts and panels before operating.

Failure to do so can result in death or e_ectrical shock.

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower access panel and the

two screws from the base grille area of the front panel

support. Pull forward to remove the lower access panel.

3. Pull the bottom forward and then pull down to remove the

lower access panel.

4. Remove dirt and lint from the condenser fins and the unit

compartment with a brush attachment on a vacuum cleaner.

5. Replace the lower access panel using the four screws.

6. Plug in ice maker or reconnect power.

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the

bin.

3. Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap securely on the water pan.

If the drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

4. Remove the two screws that hold the cutter grid cover in

place and remove the cutter grid cover.

5. Unplug the wiring harness from the left side of the cutter grid.

A. Cutter grid cover

B. Screws

6. Unplug the ice level sensor from the right side of the cutter

grid. Pull the ice level sensor down and forward away from

the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter

grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side

of the cutter grid bracket stays with the cutter grid.

A ................. _ ..................................D

S ...............................

C .......................................

A. Cutter grid harness

B. Screw

C. Cutter grid

D. Ice level sensor harness

E. Plastic spacer

F. Screw

Remove the two thumb screws that hold the water pan in

place. Push down with one hand on the front of the pan while

pulling forward on the bottom back side.

A. Water pan

B. Water pan thumb screws

C. Drain cap

Remove, clean and replace the ice scoop and ice scoop

holder.

• After removing the ice scoop, remove the holder by

removing the two thumb screws.

• Wash the ice scoop holder along with the other interior

components using the following instructions.

• Replace the ice scoop holder by replacing the thumb

screws.

A. Thumb screws

B. Ice scoop holder

10. Wash the interior components (cutter grid, exterior of hoses,

and water pan) and the storage bin, door gasket, ice scoop,

and ice scoop holder with mild soap or detergent and warm

water. Rinse in clean water. Then clean the same parts with a

solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)

warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in

dishwasher. They cannot withstand temperatures above

145°F (63°0).

11. Replace water pan by pushing back on the bottom with one

hand while pushing up and back on the top. Secure the water

pan by replacing both screws.

12. Check the following:

• Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

• Hose from water pan is inserted into storage bin drain

opening.

13. Slide the cutter grid back into place and secure it by

replacing the right-hand screw and plastic spacer. Then

tighten the left-hand screw. Reconnect the cutter grid

harness and the ice level sensor harness.

14. Replace the plastic cutter grid cover and the two screws.

15. Plug in ice maker or reconnect power.

Eiectricam Shock Hazard

Disconnect power before servicing.

Repmace aH parts and panels before operating.

Failure to do so can resumt in death or electrical shock.

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the two screws in the lower access panel and the

two screws from the base grille area of the front panel

support. Pull forward to remove the lower access panel.

5. Disconnect the inlet and outlet lines to water valve. Allow

these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32°F (0°C), remove

water from the drain line.

For ice makers with a drain pump installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

• Pour 1 qt (0.95 L) of water into the ice bin near the drain

and let the unit stand for approximately 5 minutes. This

will allow the water in the bin to drain into the drain pump

so that the pump will remove the remaining water from

the ice bin and the drain pump.

• Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any additional

oiling throughout the normal life of the machine.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your ice maker will not operate

Electrica) Shock Hazard

Plug into a grounded 3 prong out(et,

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord,

Failure to fellow these instruct}arts can result in death,

fire, or e_ectr}cal shock,

Is the power cord plugged in? Plug into a grounded 3 prong

outlet.

Is the control set to ON? Be sure that the control is set to

ON,

Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse or reset the circuit breaker, If the

problem continues, call an electrician.

Is the room temperature cooler than normal? Room

temperature must be above 55°F (13°C). Otherwise, bin

thermostat may sense cold room temperature and shut off

even though the bin is not full of ice. Also, unit may not restart

once it does shut off.

Does the red light come on when the Clean button is

pushed? The ice maker is receiving power but may need

cleaning. See "Cleaning."

Does the ice maker have a drain pump? Ifthere was a large

amount of water added to the ice maker, wait a few minutes

for the drain pump to clear. If there is still water in the bin,

check to see whether the drain hose is kinked.

Ice maker seems noisy

• Is water being circulated through the ice maker? This is

normal operation, Water is added once per ice-making cycle,

• is the water in the reservoir overflowing? This is normal,

This overflow helps to purge minerals that were removed from

the water during the ice making process.

• is there a "whooshing" sound? Check the following things:

• Make sure that the water supply is hooked up and turned

on.

• Make sure that the drain cap is tight and the water drain

pan pump is securely attached to the water pan.

Is there ice between the evaporator plate and the cutting

grid? Check to be sure that the ice maker is level. See

"Leveling." If the ice maker is level, and the problem persists,

run a cleaning cycle. See "Cleaning."

Ice maker runs but produces no ice

• Is the control set to ON? Be sure that the control is set to

ON.

• Is the water supply connected? Make sure the water supply

is properly connected and turned on.

• Is the drain cap securely in place? If the drain cap is loose,

water will empty from the water pan, and you will have either

thin ice or no ice, Tighten the drain cap.

• Is there debris in the drain tube? Clean the drain tube.

• Is there a kink in the drain line? Be sure that there are no

kinks in the line.

• Is the service light flashing on and off continually? Call for

service.

Ice maker runs but produces very little ice

• Is the room temperature hotter than normal? Room

temperatures of more than 90°F (32°C) will normally reduce

ice production.

EJectrical Shock Hazard

Disconnect power before servicing,

Replace a)(parts and panels before operating.

Failure to do so can result in death or electrical shock.

Is the condenser dirty? Dirt or lint may be blocking the

airflow through the condenser. See "Condenser."

Is there scale buildup in the ice maker? If there is white

scale buildup in the ice maker's water or freezing system, you

should clean the ice maker. See "Interior Components" in the

"Cleaning" section.

Is the drain cap securely in place? If the drain cap is loose,

water will empty from the water pan, and you will have either

thin ice or no ice. Tighten the drain cap if it is loose.

Grid is not cutting ice sheets

Is the cutter grid securely in place? Check the cutter grid

harness plug to make sure the connection is intact. See

"Interior Components" section of "Cleaning" for instructions

on cutter grid removal.

! _:i_,:_

Off taste, odor or gray color in the ice

• Is there unusually high mineral content in the water

supply? The water may need to be filtered or treated.

• Is there mineral scale buildup? Clean your ice maker. See

"Ice Maker System" in the "Cleaning" section.

• Are there food items stored in the ice bin? Do not store any

foods in the ice bin.

• Were all the packaging materials removed? Make sure that

all packaging materials were removed at the time of

installation.

Thin, soft or clumps of ice

• Is there unusually high mineral content in the water

supply? The water may need to be filtered or treated.

• Is there mineral scale buildup? Clean your ice maker. See

"Ice Maker System" in the "Cleaning" section.

• Are there clumps of ice in the bin? If ice is not used

regularly it will melt and form clumps. Break the clumps with

the ice scoop provided.

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

• Is the drain hose aligned over the drain? Move the ice

maker to align the drain. See "Water Supply Connection."

NOTE: Service technicians can not repair plumbing problems

outside of the ice maker. Call a licensed, qualified plumber.

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use FSP®replacement parts. FSP®replacement parts will fit

right and work right, because they are made with the same

precision used to build every new WHIRLPOOL _ appliance.

To locate FSP_ replacement parts in your area, call our Customer

eXperience Center telephone number or your nearest designated

service center.

Call the Customer eXperience Center toll free: f-800-253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool designated service technicians

are trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, M149022-2692

Please include a daytime phone number in your correspondence.

Call the Whirlpool Canada LP Customer Interaction Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Use and maintenance procedures.

• Accessory and repair parts sales.

Referrals to local dealers, repair parts distributors, and

services companies. Whirlpool Canada designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool Canada

LP with any questions or concerns at:

Customer Interaction Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

WHIRLPOOLCORPORATIONMAJORAPPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

This limited warranty applies only when the major appliance is used in the country in which it was purchased.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was

purchased.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATETO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool. Inthe U.S.A., call f-800-253-1301. In Canada,

call 1-800-807-6777. 12/o5

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELAMACHINE GLA( ONS

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securit6 et de vous y conformer.

Voici le symbole d'alerte de securit&

Ce symbole d'alerte de securit6 vous signale les dangers potentiels de deces et de blessures graves h vous

et &d'autres.

Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" eu

"AVERTISSEMENT". Ces mots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement lee instructions.

Risque possible de deces ou de blessure grave si vous

ne euivez pas lee instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SC:CURIT¢:

AVERTUSSEMENT : Pour r_duire le risque dqncendie, de choc 61ectrique ou de blessures Iors de I'utiJisation

de la machine A gJagons, il convient d'observer certaines pr6cautions 616mentaires :

• Brancher sur une prise a 3 alveoles reliee a la terre.

• Ne pas enlever la broche de liaison a la terre.

• Ne pas utiliser un adaptateur.

• Ne pas utiliser un cable de ra!longe.

• Utiliser deux ou plus de personnes pour deplacer et

installer la machine a gtagons.

• Deconnecter Ia source de courant electrique avant le

nettoyage.

• Deconnecter la source de courant electrique avant

I'entretien.

_, Replacer pi_ces et panneaux avant de faire la remise

en marche.

CONSERVEZ CES INSTRUCTIONS

INSTRUCTIONSD'INSTALLATION

Risque du p•ids excessif

Utiliser deux ou plus de pereonnee pour deplacer et

installer la machine h glagons.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

• Ne pas utiliser d'instruments aceres, d'alcool &friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adhesif ou la colle. Ne pas utiliser d'eau de Javel sur

les surfaces en acier inoxydable de la machine a glagons.

Ces produits peuvent endommager la surface de votre

machine a glagons.

Nettoyage avant I utilisation

Apres avoir enleve tousles materiaux d'emballage, nettoyer

I'interieur de la machine & glagons avant de I'utiliser. Voir les

Enl_vement des mat_riaux d'emballage instructions de nettoyage dans la section "Entretien de la

machine a glagons".

Enlever le ruban adhesif et la colle de la machine a glagons avant

de I'utiliser.

• Pour enlever ce qui reste du ruban adhesif ou de la colle de la

surface exterieure de la machine a glagons, frotter la surface

vivement avec le pouce. La colle ou I'adhesif qui reste peut

_tre facilement enleve(e) en frottant une petite quantite de

liquide vaisselle sur I'adhesif avec les doigts. Rincer a I'eau

tiede et essuyer.

Pour assurer une bonne aeration de la machine a glagons,

I'avant dolt _tre completement degag& Les autres c6tes et le

dessus de I'appareil peuvent _tre dissimules, mais

I'installation dolt permettre de tirer la machine a glagons vers

I'avant pour I'entretien, si necessaire.

Pour installer la machine a gla9ons, il faut avoir un tuyau

souple d'alimentation en eau froide de 1/4"(6,35 mm) de

diametre exterieur en cuivre avec un robinet et un systeme de

vidange par gravite ou une pompe a condensats pour

pousser I'eau vers un drain existant.

Choisir un endroit bien aere ou la temperature est superieure

55°F (13°C) et inferieure a 110°F (43°C). Pour tirer le

meilleur rendement de I'appareil, la temperature ambiante

dolt se situer entre 70°F (21°C) et 90°F (32°C).

Cet appareil dolt _tre installe a un endroit protege contre les

elements, comme le vent, la pluie, les embruns ou les

egouttures.

Lorsque I'appareil est installe sous un comptoir, observer les

dimensions d'ouverture indiquees. Placer les composants

electriques et de plomberie dans la zone recommandee sur

I'illustration.

REMARQUE:

• Verifier que le cordon d'alimentation n'est pas coince

entre la machine a glagons et le placard.

• Verifier que le conduit de raccordement a la canalisation

d'eau n'est pas coince entre la machine a gla(_ons et le

placard.

• Verifier que le tuyau d'evacuation (sur certains modeles)

n'est pas coince entre la machine a gla(_ons et le placard.

34"

(86,4 cm)

Min.

341/2" 281/2"

(87,6 cm) (72,4 cm)

Max.

I-'--15"

(38,1 cm)

A. Zone recommand_e pour les composants

_lectriques et de plomberie

B. Niveau du plancher

II est recommande de choisir un emplacement ou le plancher

est de niveau. II est important que la machine a glagons soit

d'aplomb pour bien fonctionner. Au besoin, il est possible de

regler la hauteur de la machine a glagons en changeant la

position des pieds de nivellement. Voir la section

"Nivellement".

Risque de choc electrique

Brancher sur une prise a 3 alveoles retiee a la terre.

Ne pas en_ever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un cSb_e de raHonge.

Le non-respect de ces instructions peut causer

un deces, un incendie ou un choc electrique.

Avant de deplacer la machine a gla(_ons a sa place definitive, il

faut s'assurer que le raccordement electrique a ete fait

correctement.

IIfaut un circuit d'alimentation electrique CA seulement de

115 volts, 60 Hz, de 15 ou 20 amperes, mis a la terre

conformement aux instructions du Code national de I'electricite

et des codes et reglements Iocaux.

II est recommande de reserver un circuit special a la machine

glagons. Utiliser une bofte ou I'alimentation ne peut pas _tre

coupee a I'aide d'un commutateur ou d'un interrupteur a tirage.

IMPORTANT : Si ce produit est connecte & une prise protegee

par un disjoncteur de fuite & la terre, un declenchement

intempestif peut se produire et causer une perte de

refroidissement. La qualite des gla(_ons peut en _tre affectee. Si

un declenchement intempestif se produit et si les glaqons

semblent de pietre qualite, jeter le tout.

M_thode de raise a la terre recommand_e

Pour votre propre securite, cet appareil dolt _tre mis & la terre.

L'appareil comporte un cordon d'alimentation electrique a trois

broches pour la mise a la terre. Pour minimiser les risques de

choc electrique, le cordon d'alimentation electrique dolt _tre

branche sur une prise de courant murale de configuration

correspondante, a trois alveoles, reliee a la terre conformement

au Code national de I'electricite et aux codes et reglements

Iocaux. S'il n'y a pas de prise de courant correspondante, il

incombe au client de faire installer une prise de courant murale

trois alveoles mise a la terre par un electricien qualifi&

Une alimentation en eau froide avec une pression entre 30 et

120 Ib/po 2(207 et 827 kPa) est necessaire pour faire fonctionner

la machine a gla9ons. Si vous avez des questions au sujet de la

pression de votre eau, appeler un plombier qualifie agre&

Alimentation en eau par osmose inverse

IMPORTANT : La pression de I'alimentation en eau entre le

systeme d'osmose inverse et la valve d'arrivee d'eau de la

machine & gla(;ons dolt _tre entre 30 et 120 Ib/po 2 (207 et

827 kPa).

Si un systeme de purification de I'eau par osmose inverse est

raccorde & votre alimentation en eau froide, la pression de I'eau

au systeme dolt _tre d'un minimum de 40 a 60 Ib/po 2(276

414 kPa). Le systeme d'osmose inverse dolt fournir 1 gal. (3,79 L)

d'eau par heure pour un fonctionnement correct de la machine

glagons.

Si la pression de I'eau au syst_me d'osmose inverse est

inferieure a 40 a 60 Ib/po 2(276 a 414 kPa) :

• Verifier si le filtre du syst_me d'osmose inverse est bloque et

le remplacer si necessaire.

• Laisser le reservoir du systeme d'osmose inverse se remplir

apres une utilisation intense.

Si vous avez des questions au sujet de la pression de votre eau,

appeler un plombier qualifie agree.

IIest important que la machine a glagons soit d'aplomb pour bien

fonctionner. Selon I'endroit ou vous installez la machine &

glagons, vous pourrez avoir a effectuer plusieurs ajustements

pour la mettre d'aplomb. Vous pouvez egalement utiliser les

pieds de nivellement pour baisser la hauteur de la machine

glagons pour les installations sous comptoir.

Outillage n_cessaire :

Rassembler les outils et pieces necessaires avant de commencer

I'installation.

• Niveau de 9"

• Cle a molette

REMARQUE : II est plus facile d'ajuster les pieds de nivellement

si on se fait aider par une autre personne.

1. Deplacer la machine a glagons a son emplacement final.

REMARQUE : Dans le cas d'une installation encastree,

deplacer la machine a glagons le plus pres possible de son

emplacement final.

Placer un niveau a bulle sur le dessus du produit pour voir si

la machine & gla(_ons est d'aplomb d'avant en arriere et

transversalement.

Pousser vers le haut sur la pattie superieure avant de la

machine a glagons pour reperer les vis de nivellement qui se

trouvent sur le fond avant de la machine a glagons.

Au moyen d'une cle a molette, modifier la hauteur des pieds

comme suit :

• Tourner le pied de nivellement vers la droite pour abaisser

ce c6te de la machine a glagons.

• Tourner le pied de nivellement vers la gauche pour

soulever ce c6te de la machine a glagons.

REMARQUE : La machine & gla(_ons ne devrait pas osciller.

Utiliser des cales pour accroltre la stabilite au besoin.

5. Pousser vers le haut sur la partie arriere de la machine

glagons pour reperer les pieds de nivellement qui se trouvent

sur le fond arriere de la machine a gla9ons.

6. Suivre les instructions de I'etape 4 pour modifier la hauteur

des pieds.

7. Utiliser un niveau a bulle pour reverifier que la machine

glagons est d'aplomb d'avant en arriere et transversalement.

Si elle n'est pas d'aplomb, repeter les etapes 2 a 5. Si la

machine est d'aplomb, passer a la section "Raccordement

la canalisation d'eau".

Lire attentivement toutes les instructions avant de

commencer.

IMPORTANT :

• L'installation de la plomberie doit _tre conforme au Code

national de plomberie et respecter les codes Iocaux de

plomberie.

• Utiliser un tuyau en cuivre et verifier s'il y a des fuites.

• Installer les tuyaux en cuivre seulement la ou les

temperatures resteront au-dessus du point de congelation.

Outillage n_cessaire :

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

• Tournevis a lame plate

• Cles plates de 7A6"et de 1/2"ou deux cles a molette

• Tourne-ecrou de 1/4"

• Foret de 1/4"

• Perceuse manuelle ou electrique convenablement mise a la

terre

REMARQUE : Votre marchand de machine a glagons a une

trousse qui comprend un robinet d'arr_t aetrier de 1/4"(6,35 mm),

un raccord-union et un tuyau en cuivre. Avant de faire un achat,

s'assurer que le robinet d'arr_t a etrier respecte les codes Iocaux

de plomberie. Ne pas utiliser de robinet d'arr_t a etrier perforant

ou de 6A6"(4,76 mm) qui reduit le debit d'eau et qui se bouche

plus facilement.

Raccordement du tuyau d'eau

Couper I'alimentation principale en eau. Ouvrir le robinet le

plus proche assez Iongtemps pour vider I'eau du tuyau.

Trouver un tuyau vertical d'alimentation en eau froide de 1/2"

(12,70 mm) a 11/4'' (3,18 cm) a proximite de la machine

gla(_ons.

REMARQUI= : Un conduit horizontal fonctionnera, mais on

doit observer le precede suivant : Percer par le dessus de la

canalisation et non pas par le dessous. Ainsi, I'eau ne

risquera pas d'arroser la perceuse. Ceci emp_che egalement

les sediments qu'on trouve normalement dans I'eau de

s'accumuler dans le robinet d'arr_t.

,A,I'aide d'une perceuse electrique reli_e a la terre, percer un

trou de 1A"(6,35 mm) dans le tuyau d'alimentation en eau

froide que vous avez choisi.

Fixer le robinet d'arr_t sur le tuyau d'alimentation en eau

I'aide d'une bride pour tuyau. IIfaut s'assurer que I'extremite

de sortie est bien inseree dans le trou de 1A"(6,35 mm) perce

dans le tuyau d'eau et que la rondelle est placee sous la bride

du tuyau. Serrer I'ecrou de garniture. Serrer soigneusement et

uniformement les vis fixant la bride de tuyau sur le tuyau afin

que la rondelle forme un scellement etanche. Ne pas serrer la

bride du tuyau a I'exces sans quoi le tuyau d'alimentation en

eau froide pourrait 6tre ecrase s'il s'agit d'un tuyau en cuivre

souple. Ne pas utiliser un robinet d'arr_t a etrier perforant ou

de 3A_"(4,76 mm) qui pourrait reduire le debit d'eau et qui se

bouche plus facilement.

On est maintenant pr_t & connecter le tuyau en cuivre. Utiliser

un tuyau en cuivre souple de 1/4"(6,35 mm) de diametre

exterieur pour I'alimentation en eau froide.

• S'assurer d'avoir la Iongueur necessaire pour le

raccordement. IIfaut s'assurer que les deux extremites

du tuyau en cuivre sont bien coupees a angle droit.

• Installer le manchon et I'ecrou acompression sur le tuyau

en cuivre (voir I'illustration). Ins@er I'extremit6 du tuyau

aussi profondement que possible dans I'extremit6 de

sortie et & I'equerre. Visser I'ecrou a compression sur

I'extremit6 de la sortie a I'aide d'une cle reglable. Ne pas

serrer a I'exces.

.................. A

H ...........................B

E -¸¸¸°

A. Tuyaud'alimentation en eau E.E-croude compression

froide F.Manchon b compression

B.Bride G.Robinet d'arr_t

C.Tuyauen cuivre H.Ecrou de la garniture

D.Raccord (achet_)

Placer I'extremite libre du tuyau dans un contenant ou evier

et retablir I'alimentation principale en eau pour nettoyer le

tuyau jusqu'a ce que I'eau en sorte claire. Fermer le robinet

d'arr_t sur le tuyau d'alimentation en eau.

REMARQUE : Toujours vidanger le tuyau d'alimentation en

eau avant de faire le raccordement final sur I'entree du

robinet pour emp_cher tout mauvais fonctionnement

eventuel du robinet.

Courber le tuyau de cuivre de fagon a faire un raccordement

sur I'entree du robinet quise trouve a I'arriere de la machine

glagons (voir I'illustration). Laisser un serpentin de tube en

cuivre pour permettre de sortir la machine a glagons de

I'armoire ou du mur en cas d'intervention de service.

VUE ARRII_RE

A. Tuyau de vidange (modeles avec

pompe de vidange seulement)

B. Tuyau de ventilation (medeles avec

pompe de vidange seulement)

C. Tuyau d'alimentation en eau

Visser I'ecrou dans le raccord a I'extremite du tuyau en

cuivre. Serrer I'ecrou manuellement. Ensuite le serrer deux

tours de plus avec une cle. Ne pas serrer a I'exces.

REMARQUE : Pour eviter les vibrations, veiller a ce que les

tuyaux en cuivre nesoient pas en contact avec les parois

laterales de la machine a glagons ou d'autres composants

I'int@ieur de la caisse.

A B C D E F G

A. Canalisation jusqu'a D. Raccord (achet_)

la machine a glaqons E. Bague

B. Ecrou (achet_) F Ecrou

C. Bague (achet_e) G. Canalisation fournie

provenant de la

machine a glagons

9. OUVRIR le robinet d'arr_t.

10. Verifier s'il y a des fuites. Serrer tousles raccords (y compris

les raccordements de la valve) ou les ecrous qui coulent.

Vidange par gravit_

IIfaut raccorder le tuyau de vidange de la machine a glagons

votre drain de vidange conformement aux codes et reglements

Iocaux et provinciaux. Si la machine a glagons est fournie avec

un drain de vidange par gravite, il faut suivre les instructions ci-

dessous Iors de I'installation des tuyaux de vidange. Ceci aidera

eviter que I'eau ne refoule dans le bac d'entreposage de la

machine a glagons et eventuellement sur le plancher et ne cause

des dommages.

• Les tuyaux de vidange doivent avoir au moins %" (15,88 mm)

de diametre int@ieur.

Les tuyaux de vidange doivent avoir une pente de 1" pour

chaque 48" (2,54 cm pour chaque 122 cm) de Iongueur ou

une pente de 1/4"pour chaque 12" (6,35 mm/30,48 cm) et ne

comporter aucun point bas o(_I'eau pourrait stagner.

• Les drains de vidange de plancher doivent _tre suffisamment

grands pour recevoir I'eau de vidange provenant de toutes

sources.

L'installation ideale a un tuyau de rejet a I'egout avec un

reducteur de vidange PVC de 11/2'' (3,81 cm) a 2" (5,08 cm)

installe directement sous la sortie du tuyau de vidange

comme sur I'illustration. IIfaut maintenir un ecart anti-retour

de 1" (2,54 cm) entre le tuyau de la pompe de vidange et le

tuyau de rejet a I'egout.

• II sera peut-_tre souhaitable d'isoler le tuyau de vidange

completement jusqu'a I'entree du drain de vidange.

VUE LATC:RALE

(9,2 cm)

23"

(58,4 cm)

2".11/2"

(5 cm - 3,8 cm)

A. Tuyau de vidange

B. Ecart anti-retour de 1" (2,54 cm)

C. R_ducteur du drain de vidange PVC

D. Le centre du drain devrait se trouver a 23" (58,4 cm) du devant de

la porte (avec ou sans le panneau de _" (1,91 cm) sur la porte). Le

drain dolt aussi _tre centre de gauche a droite (7_J' [18,56 cm] de

chaque c6t_ de la machine a glaqons).

Syst_me avec pompe de vidange (sur certains modules)

Raccorder le drain de la machine & gla(_ons au drain de vidange

conformement au Code international de plomberie et a tousles

codes et reglements Iocaux.

REMARQUE : Si le tuyau de vidange devient tordu et que I'eau

ne peut passe vidanger, votre machine a glagons ne

fonctionnera pas.

Raccordement du conduit d'_vacuation

Apres avoir verifie que le systeme de vidange est adequat, il faut

preceder tel que decrit ci-dessous pour bien mettre la machine

glagons en place :

Risque du poide exceesif

Utiliser deux ou plus de personnes pour deplacer et

installer la machine a gla_ons.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure,

2. Style 1 - Pour un systeme de vidange par gravite, pousser la

machine a gla9ons en position pour que le conduit de

vidange soit positionne au-dessus du reducteur de vidange

en PVC. Voir "Vidange par gravite" precedemment dans cette

section. Style 2 - Pour le systeme avec pompe de vidange,

connecter le tuyau de sortie de la pompe au drain. Voir

"Systeme avec pompe de vidange" precedemment dans

cette section.

3. Verifier a nouveau la machine a gla(_ons pour s'assurer qu'elle

est bien d'aplomb. Voir la section "Nivellement".

4. Si le code sanitaire local I'exige, sceller la machine sur le

plancher a I'aide d'un produit de calfeutrage approuve une

fois que les raccordements d'eau et d'electricite ont ete faits.

OUTILLAGE NI_CESSAIRE :

Rassembler les outils et pieces necessaires avant de commencer

I'installation.

• Clede¾_"

• Couteau a mastic plat

• Cle de V4" • Tournevis Phillips

Axe

Vis de charnierea t_te hexagonale

Risque de choc etectrique

Brancher sur une prise a 3 a_veo_ee reliee a la terreo

Ne pas en_ever la broche de liaison a _aterreo

Ne pas utiliser un adaptateuro

Ne pas utilieer un cSb_e de rallonge.

Le non-respect de ces instructions peut causer

un deces, un incendie ou un choc electdqueo

1. Brancher I'appareil sur une prise a 3 alveoles reliee a la terre.

Vis de poign_e Vis d'embout

D_pose de la porte

1. Debrancher la machine a glagons ou deconnecter la source

de courant electrique.

2. Oter les vis de la poignee et la poignee (sur certains

modeles). Garder les pieces ensemble et les mettre de c6te.

3. Tirer I'axe de la charniere superieure.

4. Retirer la porte des charnieres et revisser I'axe superieur dans

la charniere superieure.

5. Inverser les embouts de porte comme suit :

• Oter les deux vis et embouts (superieur et inferieur).

• Placer I'embout superieur a la partie inferieure du c6te

oppose de la porte avec le long c6te plat face au devant

de la porte.

• Placer I'embout inferieur a la partie superieure du c6te

oppose de la porte avec le long c6te plat face au devant

de la porte.

6. Mettre la porte de c6te.

Inversion des charni_res

1. Devisser et 6ter la charniere superieure. Reinstaller les vis

darts les trous vides de charniere.

2. Oter les vis du c6te oppose inferieur de la caisse de la

machine a glagons. Inverser la charniere superieure de telle

sorte que I'axe pointe vers le haut. Placer la charniere du c6te

oppose inferieur de la machine a glagons et serrer les vis.

3. Enlever la douille de plastique de I'axe de la charniere de la

"vieille" charniere inferieure et la replacer sur la nouvelle

charniere inferieure.

4. Oter les vis de la "vieille" charniere inferieure et la charniere.

Reinstaller les vis darts les trous vides de la charniere.

5. Oter les vis du c6te superieur oppose de la caisse de la

machine a glagons. Inverser la charniere de telle sorte que

I'axe pointe vers le bas. Placer la charniere du c6te oppose

superieur de la machine a gla9ons et serrer les vis.

6. Oter I'axe de la charniere superieure.

R_installation de la porte

1. Placer la douille de plastique de la charniere darts le trou de la

charniere superieure sur la porte. Aligner la porte avec le trou

de la charniere superieure et reinstaller I'axe superieur.

2. Reinstaller la poignee et les vis de la poignee.

Charni_re sup_rieure

inversion du Ioquet de porte

1. Oter les bouchons de trous du c6te oppose de la porte et les

mettre de c6te.

2. Oter les vis du Ioquet de porte magnetique et les reinstaller

du c6te oppose de la porte.

3. Pousser les bouchons de trous en place du c6te oppose de

la porte.

Risque de choc e_ectrique

Brancher sur une prise a 3 a_veo_es retiee a la terre.

Ne pas en_ever la broche de _iaison a _aterreo

Ne pas utiiiser an adaptateuro

Ne pas utiliser un c_ble de raHonge.

Le nomrespect de ces instructions peat causer

un deces, an incendie ou un choc electrique.

....................................A

_ ...................C

iiiiiiiiiiiiiii

A.Axe

B.Douillede I'axede la charniere

C.Charniere

D.Visde charniere a t_tehexagonale

Charni_re inf_rieure

A. Vis de charniere b t_te hexagonale

B.Douille de I'axe de la charniere

C. Charniere

D. Axe

4. Brancher la machine a glagons ou reconnecter la source de

courant electrique.

II est possible que votre nouvelle machine & gla(_ons emette des

bruits qui ne vous sont pas familiers. Comme ces bruits sent

nouveaux, ils peuvent vous inquieter. La plupart de ces nouveaux

bruits sont normaux. Des surfaces dures comme le plancher, les

murs et les armoires peuvent faire paraitre les bruits plus forts

qu'en realite. Les descriptions suivantes indiquent les genres de

bruits qui peuvent _tre nouveaux pour vous et leur cause.

• Vous entendrez un bourdonnement Iorsque la valve d'eau

s'ouvre pour remplir le reservoir d'eau pour chaque

programme.

• Des vibrations sonores peuvent provenir de I'ecoulement du

refrigerant, de la canalisation d'eau ou d'articles places sur la

machine a glagons.

• Le compresseur a haute efficacite peut produire un son aigu

ou de pulsation.

• L'eau coulant sur la plaque d'evaporation peut produire un

son d'eclaboussement.

• L'eau coulant de la plaque d'evaporation au reservoir d'eau

peut produire un son d'eclaboussement.

• /_,la fin de chaque programme, vous pouvez entendre un

gargouillement attribuable au refrigerant qui circule dans

votre machine a glagons.

• Vous pouvez entendre de I'air qui est transmis au condenseur

par le ventilateur du condenseur.

• Au cours du programme de recolte, vous pouvez entendre un

bruit sourd Iorsque la plaque de glace glisse de I'evaporateur

sur la grille de coupe.

Lors de la mise en marche initiale de la machine a glat:ons, il

est possible que vous entendiez I'eau couler continuellement.

La machine a glagons est programmee pour effectuer un

programme de rin9age avant de commencer a fabriquer de la

glace.

La page charge ...

Whirlpool GI15NDXTS0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GI15NDXTS0

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool GI15NDXTS0 Owner's manual

Whirlpool GI15NDXTS0 Le manuel du propriétaire

Whirlpool GI15NDXTS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents