Life Fitness Exercise Bike Lifecycle 9100 Mode d'emploi

Catégorie
Fitness, gymnastique
Taper
Mode d'emploi
TTrreeaaddmmiillll
OPERATION MANUAL
1
LIFE FITNESS ASIA PACIFIC LTD
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
FAX: (+852) 2575.6001
LIFE FITNESS ATLANTIC BV
LIFE FITNESS BENELUX
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180.646.666
FAX: (+31) 180.646.699
LIFE FITNESS DO BRAZIL
Av. Dr. Dib Sauaia Neto 1478
Alphaville, Barueri, SP
06465-140
BRAZIL
Telephone (+55) 11.4193.8282
FAX: (+55) 11.4193.8283
LIFE FITNESS AUSTRIA
Vertriebs GmbH
Hintschiggasse 1
1100 Vienna
AUSTRIA
Telephone: (+43) 1.61 57 198
FAX: (+43) 1.61 57 198.20
LIFE FITNESS IBERIA
Pol. Ind. Molí dels Frares. c/C, nº 12
08620 Sant Vicenç dels Horts (Barcelona)
España
Telephone: (+34) 93.672.4660
FAX: (+34) 93.672.4670
LIFE FITNESS EUROPE GMBH
Siemensstrasse 3
85716 Unterschleissheim
GERMANY
Telephone: (+49) 89.31 77 51.0
FAX: (+49) 89.31 77 51.99
LIFE FITNESS ITALIA S.R.L.
Via Elvas 92
39042 Bressanone (BZ)
ITALY
Telephone: (+39) 0472.835 470
FAX: (+39) 0472.833 150
LIFE FITNESS LATIN AMERICA
and CARIBBEAN
10601 West Belmont Avenue
Franklin Park, Illinois 60131
U.S.A.
Telephone: (+1) 847.288.3300
FAX:(+1) 847.288.3762
LIFE FITNESS UK LTD
Queen Adelaide
Ely, Cambs CB7 4UB
UNITED KINGDOM
Telephone: (+44) 1.353.666 017
FAX: (+44) 1.353.666 018
LIFE FITNESS JAPAN
Nippon Brunswick Bldg., #8F
5-27-7 Sendagaya
Shibuya-Ku, Tokyo
Japan 151-0051
Telephone: (+81) 3.3359.4309
FAX: (+81) 3.3359.4307
M051-00K20-E157
10/01
C
ORPORATE HEADQUARTERS
10601 West Belmont Avenue
Franklin Park, Illinois 60131 • U.S.A.
847.288.3300 • FAX: 847.288.3703
800.735.3867 (Toll-free within U.S.A., Canada)
INTERNATIONAL OFFICES
Before using this product, it is essential to read
this ENTIRE operation manual and ALL installation instructions.
It describes equipment setup and instructs
members on how to use it correctly and safely.
FCC Warning - Possible Radio / Television Interference
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial envi-
ronment. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference at his own
expense.
Class SB (Studio): Professional and / or commercial use.
CAUTION: Any changes or modifications to this equipment could void the prod-
uct warranty.
Any service, other than cleaning or user maintenance, must be performed by an authorized ser-
vice representative. There are no user serviceable parts.
2
T
ABLE OF CONTENTS
Section Description Page
1. Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.2 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Electrical Power Requirements
Grounding Instructions
Wax bag Instructions
How to Position and Stabilize the Treadmill
Power Switch
Setting the Clock
Centering the Belt
Fitness Networking
Power Cord Routing
2. The Display Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.1 Display Console Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.2 Display Console Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.3 Reading Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.4 Accessory Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3. Heart Rate Zone Training® Exercise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.1 Why Heart Rate Zone Training® Exercise . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.2 Heart Rate Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
The Optional Heart Rate Chest Strap
4. The Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.1 Workout Overviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.2 Using the Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.3 Workout Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Quick Start
Fat Burn
Cardio
Hill
Random
Manual
Fit Test
4.4 Maximizing Workouts on a Life Fitness Treadmill . . . . . . . . . . . . . . . . . . . . . . .28
Selecting an Intensity Level
Using InstaPace
TM
Feedback
Using ZerOut
TM
Speed Control
Cool-Down
4.5 Logging On to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5. The Managers Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5.1 Entering and Using the Manager's Configuration . . . . . . . . . . . . . . . . . . . . . . .30
5.2 Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Using the MaxTime
TM
Setup
Using the Standby Setup
3
6. Service and Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
6.1 Preventive Maintenance Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
6.2 Preventive Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6.3 Troubleshooting the Optional Heart Rate Chest Strap . . . . . . . . . . . . . . . . . . . .35
Heart Rate Is Erratic Or Absent Entirely
Heart Rate Reading Is Erratic Or Extremely High (Above 200)
6.4 Removing the Accessory Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
6.5 How to Adjust and Tension the Striding Belt . . . . . . . . . . . . . . . . . . . . . . . . . . .36
The Belt Tensioning Bolts
Tracking (Centering) the Striding Belt
Tensioning an Existing Striding Belt
6.6 Cleaning the Wax Nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
6.7 How to Obtain Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
7. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
7.1 Life Fitness 9100 Treadmill Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
© 2001 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifecycle,
FlexDeck, and Heart Rate Zone Training are registered trademarks, and InstaPace, ZerOut, MaxTime,
Intelli, MagnaDrive, Lifespring and "Rely on It" are trademarks of Brunswick Corporation. Polar is a
registered trademark of Polar Electro, Inc. Cardio Theater is a registered trademark of Cardio Theater
Holdings and a wholly owned subsidiary of ClubCom corporation. Broadcast Vision is a trademark of Broadcast
Vision, Inc. Fitlinxx is a registered trademark of the Integrated Fitness Corp. Any use of these trademarks,
without the express written consent of Life Fitness or the corresponding companies is forbidden.
4
This Operation Manual describes the functions of the following products:
Life Fitness Treadmills:
9100
See "Specifications" in this manual for product specific features.
Life Fitness STRONGLY recommends seeing a physician for a complete medical exam before
undertaking an exercise program, particularly if the user has a family history of high blood pres-
sure or heart disease, or is over the age of 45, or smokes, has high cholesterol, is obese, or has
not exercised regularly in the past year.
If, at any time while exercising, the user experiences faintness, dizziness, pain, or shortness of
breath, he or she must stop immediately.
5
1
GETTING STARTED
1.1 IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using the treadmill.
DANGER: To reduce the risk of electrical shock, always unplug this Life Fitness product
before cleaning or attempting any maintenance activity.
WARNING: To reduce the risk of burns, fire, electric shock, or injury, it is imperative to
connect each product to a properly grounded electrical outlet.
To disconnect, turn power OFF at the ON/OFF switch, then remove plug from electrical
outlet.
Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it
has been dropped, damaged, or even partially immersed in water. Contact Life Fitness
Customer Support Services.
Position this product so that the power cord plug is accessible to the user.
Keep the power cord away from heated surfaces. Do not pull the equipment by the power
cord or use the cord as a handle. Do not run the power cord on the floor under or along the
side of the treadmill.
If the electrical supply cord is damaged, it must be replaced by the manufacturer, an autho-
rized service agent, or a similarly qualified person to avoid a hazard.
Do not use this product in areas where aerosol spray products are being used or where
oxygen is being administered. Such substances create the danger of combustion and
explosion.
Always follow the console instructions for proper operation.
Close supervision is necessary when used near children, invalids or disabled persons.
Do not use this product outdoors, near swimming pools or in areas of high humidity.
Never operate a Life Fitness product with the air openings blocked. Keep air openings free
of lint, hair, or any obstructing material.
Never insert objects into any opening in this product. If an object should drop inside, turn off
the power, unplug the power cord from the outlet, and carefully retrieve it. If the item cannot
be reached, contact Life Fitness Customer Support Services.
Never place liquids of any type directly on the unit, except in an accessory tray or holder.
Containers with lids are recommended.
Wear shoes with rubber or high-traction soles. Do not use shoes with heels, leather soles,
cleats or spikes. Make sure no stones are embedded in the soles.
Keep all loose clothing, shoelaces, and towels away from moving parts.
Do not use this product in bare feet.
6
Do not reach into, or underneath, the unit or tip it on its side during operation.
Keep the area six feet (two meters) by three feet (one meter) behind the treadmill clear of
any obstructions, including walls, furniture, and other equipment.
Handrails may be held to enhance stability as needed, but are not for continuous use.
Never mount or dismount the treadmill while the running belt is moving. Use the handrails
whenever additional stability is required. In case of an emergency, such as tripping, grasp
the handrails, and place the feet on the side platforms.
Never walk or jog backwards on the treadmill.
When it is necessary to immobilize the treadmill, set the display to read SELECT WORK-
OUT. (Press the STOP key twice if not already there.) Then hold down the SPEED DOWN
key and press the PAUSE key. The treadmill now displays IMMOBILIZED. In this state, the
treadmill cannot be operated. The main motor, inline and waxer are all disabled. The tread-
mill will remain in this state across resets, power cycles, etc. To restore normal operation,
repeat the same key sequence: hold down the SPEED DOWN key, and press the PAUSE
key. The treadmill will display SELECT WORKOUT again.
Use this appliance only for its intended use as described in this manual. Do not use attach-
ments that have not been recommended by the manufacturer.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
7
1
POINT DE DÉPART
1.1 CONSIGNES DE SÉCURITÉ IMPORTANTES
Pour réduire les risques de décharges électriques, l'appareil Life Fitness doit toujours être
débranché avant tout nettoyage ou travail d'entretien.
Pour réduire les risques de brûlures, d'incendies, de décharges électriques ou de blessures,
tout appareil doit être branché impérativement sur une prise électrique correctement mise à la
terre.
Pour d brancher l'appareil, coupez l'alimentation au niveau de l'interrupteur de marche/arrêt,
puis retirez la fiche de la prise électrique.
Ne faites jamais fonctionner d'appareil Life Fitness dont le cordon d'alimentation ou la fiche
seraient abîmés, qui aurait fait une chute ou qui aurait été endommagé ou partiellement
plongé dans l'eau. Contactez le service après-vente de Life Fitness.
Placez ce produit de manière à ce que l'utilisateur puisse accéder à la fiche du cordon d'ali-
mentation.
Maintenez le cordon d'alimentation à l'écart des surfaces chaudes. Ne tirez pas l'appareil
par son cordon et n'utilisez pas celui-ci pas comme poignée. Ne placez pas le cordon sur le
sol sous le tapis roulant ni le long de l'appareil.
Si le cordon d'alimentation électrique est endommagé, il doit être remplacé par le fabricant,
par un réparateur agréé ou par une personne qualifiée afin d'éviter tout danger.
N'utilisez pas ce produit dans des zones où vous utilisez des aérosols ou administrez de
l'oxygène. De telles substances pourraient entraîner des risques d'incendie et d'explosion.
Pour un fonctionnement correct, suivez toujours les instructions de la console.
Une surveillance étroite est nécessaire en cas d'utilisation par des enfants, des personnes
invalides ou handicapées.
N'utilisez pas ce produit à l'extérieur, près d'une piscine ou dans endroits très humides.
8
Ne faites jamais fonctionner de produit Life Fitness dont les bouches d'aération seraient blo-
quées. Maintenez-les exemptes de peluches, de cheveux ou de toute obstruction.
N'insérez jamais d'objet dans les ouvertures de cet appareil. Si un objet tombe dedans,
coupez l'alimentation électrique, débranchez le cordon de la prise et récupérez-le avec pré-
caution. Si vous ne pouvez pas l'atteindre, consultez le service après-vente de Life Fitness.
Ne placez jamais de liquides d'aucune sorte directement sur l'appareil, sauf si vous dis-
posez d'un support ou d'un plateau pour accessoires. Il est recommandé d'utiliser des con-
teneurs munis d'un couvercle.
Portez des chaussures avec semelles en caoutchouc ou antidérapantes. N'utilisez pas de
chaussures à talons, de semelles en cuir ou à crampons. Assurez-vous qu'aucun caillou ne
s'est incrusté dans les semelles.
Maintenez les vêtements lâches, les lacets et les serviettes à l'écart des pièces en mouve-
ment.
N'utilisez pas cet appareil sans chaussures.
Ne placez pas les mains sous ou dans l'appareil, et ne le renversez pas sur le côté pendant
le fonctionnement.
Derrière le tapis roulant, conservez une zone de 1,80 m sur 1 m libre de toute obstruction
(aucun mur, meuble ou autre appareil).
Les barres latérales peuvent servir à améliorer la stabilité, le cas échéant, mais elles ne
sont pas conçues pour être utilisées de façon continue.
Ne montez jamais sur le tapis roulant et n'en descendez jamais tandis qu'il tourne. Le cas
échéant, utilisez les barres latérales pour augmenter votre stabilité.
Ne marchez et ne courrez jamais à l'envers sur ce tapis roulant.
Lorsque vous devez immobiliser le tapis roulant, réglez l'afficheur sur SELECT WORKOUT
(Sélectionner exercice). (Appuyez deux fois sur la touche STOP si vous n'en êtes pas déjà
à ce point.) Maintenez ensuite la touche SPEED DOWN (Ralentir) enfoncée et appuyez sur
la touche PAUSE. Le tapis roulant affiche alors le message IMMOBILIZED (Immobilisé), état
dans lequel il ne peut plus fonctionner. Le moteur principal, le moteur en ligne et le cireur
sont désactivés. Le tapis roulant reste dans cet état pendant les remises à zéro, les arrêts
et remises en route, etc. Pour repasser en mode de fonctionnement normal, utilisez la
même combinaison de touches : maintenez SPEED DOWN (Ralentir) enfoncée et appuyez
sur PAUSE. L'appareil affichera SELECT WORKOUT (Sélectionner exercice) à nouveau.
CONSERVEZ CES INSTRUCTIONS POUR USAGE ULTÉRIEUR.
9
1.2 S
ETUP
Read the Operation Manual before setting up the Life Fitness treadmill. Place the treadmill
where it will be used before beginning the setup procedure.
ELECTRICAL POWER REQUIREMENTS
The Life Fitness Treadmill is intended for use on a normal 120-Volt electrical circuit in the United
States and Canada. The following table provides the current rating for this product based on
supply voltage. Make sure that this treadmill model supports the proper line voltage for the
installation location before plugging it into the outlet.
GROUNDING INSTRUCTIONS
This Life Fitness product must be properly grounded. If the unit malfunctions or breaks down,
proper grounding provides a path of least resistance for the electric current, which reduces the
risk of shock to anyone touching or using the equipment. Each unit is equipped with an electrical
cord, which includes an equipment grounding conductor and a grounding plug. The plug must
be inserted into an outlet that has been properly installed and grounded in accordance with all
local codes and ordinances.
A temporary adapter MUST NOT BE USED to connect this plug to a 2-pole receptacle
in North America. If a properly grounded, 20 AMP outlet is not available, one must be
installed by a qualified electrician. Models drawing 20-amps must be installed on a
dedicated line.
IL EST ABSOLUMENT INTERDIT d'employer un adaptateur temporaire pour brancher
cette fiche sur une prise à deux pôles en Amérique du Nord. Si aucune prise de 20 A
correctement mise à la terre n'est disponible, il convient d'en faire installer une par
un électricien qualifié. Les modèles utilisant 16 A ou plus doivent être installés sur
des lignes qui leur sont réservées.
A risk of electrical shock may result from improper connection of the equipment-
grounding conductor. Check with a qualified electrician if in doubt as to proper
grounding technique. DO NOT modify the plug provided with the product. If it will not
fit an electrical outlet, have a proper outlet installed by a qualified electrician.
Un branchement incorrect du conducteur de mise à la terre peut entraîner des risques de
décharge électrique. Consultez un électricien si des doutes subsistent quant à la tech-
nique de mise à la terre. NE MODIFIEZ PAS la fiche fournie avec l'appareil. Si elle ne
s'adapte pas à une prise, faites en installer une correcte par un électricien qualifié.
10
WAX BAG INSTRUCTIONS
To install the wax bag, turn the power off at the ON/OFF switch, and unplug the unit from the
electrical outlet.
Remove the access panel. Remove the two screws (A) securing the wax bag access panel
(B), located on the user left side of the unit. Remove the panel and set it aside.
Install the wax bag. Verify that the wax bag protective liner (C) is open and ready to receive the
wax bag (D). Remove the new wax bag from its packaging and carefully insert it into the access
hole. The wax bag hose faces the rear of the unit. Remove the two wingnuts (E) located just
inside the access hole. Align the mounting holes located in the wax bag flange with the two
wingnut studs (F). Secure the wax bag with the two wingnuts.
CAUTION: Be careful to not rip or damage the wax bag on the wingnuts or
wingnut studs when inserting the new wax bag.
Attach the hose clamp. Slide the hose clamp (G) over the end of the wax bag outlet hose (H).
Position the clamp approximately three inches from the end of the hose and engage it, clamping
it (1) onto the wax bag hose to prevent spillage.
Connect the wax bag hose to the pump inlet hose. Cut the end
of the wax bag hose one half-inch from the end. Slide it onto the
barbed nozzle on the wax pump inlet hose (J). Be sure to fully seat
the wax bag hose onto the inlet hose. Release the hose clamp (2).
CAUTION: Failure to release the hose clamp will result
in greatly reduced belt life.
Replace the access panel. Replace the wax bag access panel and secure it with the two
screws.
11
HOW TO POSITION AND STABILIZE THE LIFE FITNESS TREADMILL
Following all safety instructions in Section 1.1, move the
treadmill to the location in which it will be used. See
Section 7, titled Specifications, for the dimensions of the
footprint. Allow a distance of eight inches, or 21 centime-
ters, between the treadmill and other units on either side.
Allow a distance of six feet, or two meters, from the rear
of the treadmill to any object or surface.
After placing the unit where it will be used, check its stability. If there is even a slight rocking
motion or the unit is not stable, determine which stabilizing leg is not resting on the floor. To
adjust, loosen the JAM NUT (A), and turn the STABILIZING LEG (B) until the rocking motion
ceases, and both stabilizing legs rest firmly on the floor. Retighten the JAM NUT.
NOTE: It is extremely important that the stabilizing leg be correctly adjusted for proper opera-
tion. An unbalanced unit may cause striding belt misalignment.
POWER SWITCH
Located on the front panel at the base of the treadmill, the ON/OFF switch has two positions:
"I" (one) for ON and "0" (zero) for OFF.
SETTING THE CLOCK
The unit contains a clock, which is used for system maintenance and event tracking.
After the unit has been turned on
, the display will prompt for the following:
"Would you like to change the clock from GMT to local time - if YES press Enter - if NO press
Clear"
It is not mandatory to change the clock setting. To accept the current settings, press the CLEAR
key.
To change the setting, press the ENTER key. The MESSAGE CENTER displays: “CHOOSE
DISPLAY MODE - 12 HOUR MODE AM PM”. Use an ARROW key to toggle the setting to
CHOOSE DISPLAY MODE - 24 HOUR MODE. To accept the mode, press the ENTER key.
The current time (in Greenwich Mean Time) will be displayed.
Use the TIME arrows to change the hours
Use the INCLINE arrows to change the minutes
Use the SPEED arrows to change the seconds
When finished press the ENTER key. The MESSAGE CENTER displays “UPDATING CLOCK”.
At this point, the clock has been reset, and the normal startup procedure continues.
This prompt appears for the first five times that the unit is turned on, including power-ups at the
factory.
12
CENTERING THE BELT
After installing and levelling the treadmill, check the belt to ensure that it is tracking properly.
First, plug the power cord into an appropriate outlet. See Electrical Requirements at the begin-
ning of this section for details. Then, turn the treadmill ON.
Have one person stand on the platforms on either side of the treadmill belt. Do not stand on the
belt at this time. Press the QUICK START key, and increase the speed to 4.0 miles per hour
(MPH), or 6.4 kilometers per hour (KPH), using the SPEED UP arrow.
If the striding belt moves to the right while it is running, have a second person turn the right ten-
sion bolt a quarter-turn clockwise, and then turn the left tension bolt (A) a quarter-turn counter-
clockwise. See the illustration below. This action sets the striding belt tracking back to center of
the roller.
If the striding belt moves to the left, turn the left tension bolt a quarter-turn clockwise and then
turn the right tension bolt a quarter-turn counter-clockwise to start the striding belt tracking back
to center of roller.
Repeat these adjustments until striding belt appears centered. Allow the belt to continue running
for several minutes to be sure that the tracking is stabilized.
NOTE: Do not exceed one full turn of the adjusting screws in either direction. If, after one full
turn, the belt does not track properly, contact Customer Support Services. The phone numbers
are listed in Section 6.7, titled How to Obtain Product Service.
13
FITNESS NETWORKING
The two interchangeable networking ports (A) are located on the back of the display console.
These openly accessible ports allow the treadmill to be connected to a fitness entertainment
system and/or a fitness network, such as FitLinxx®.
Networking: The built-in network ports allow the unit to exchange workout information
with a fitness network database.
Fitness Entertainment: The built-in network ports allow the treadmill to power a
third-party receiver for use with an entertainment system, such as the Cardio Theater®
system or BroadcastVision
TM.
14
POWER CORD ROUTING
The power cord can be run straight from the treadmill, shortened and exited out the user-front
left side, or run under the frame and exited out the user right-rear side of the treadmill.
For efficient cord management, the following routing options are recommended:
With the power cord unplugged, insert the clips in the appropriate holes. See the illustration
below. Use Hole Pattern 1 or 2 to locate the clips and secure the power cord with the clips,
taking up any slack between clips.
NOTE: It may be necessary to tip the treadmill to route the power cord properly.
To plug the power cord into an outlet in front of the treadmill, use Hole Pattern 1 for outlets
located at the front of the machine.
To plug the power cord into an outlet in rear of the treadmill, use Hole Pattern 2 for outlets
located at the rear of the machine.
Make sure there is a 6-foot clearance behind the treadmill. Contact Life Fitness Customer
Service for a longer power cord if necessary.
WARNING: Insure that the power cord (A) does not contact the striding belt or
get pinched between the frame (C), lift arm (B) or the wheel; failure to follow this
warning may result in serious injury.
NOTE: When using Pattern 1 it is extremely important to route the power cord BETWEEN the
lift frame and the main frame.
15
2
THE DISPLAY CONSOLE
2.1 DISPLAY CONSOLE OVERVIEW
The computerized display console on the treadmill allows the user to tailor a workout to
personal fitness abilities and goals and to monitor progress. With this easy-to-use console,
the user can track fitness improvement from one workout to the next.
16
2.2 D
ISPLAY CONSOLE DESCRIPTIONS
A WORKOUT PROFILE WINDOW: During a workout, interval hills and valleys appear in this
window as rows of light stacked in columns. The number of lit rows within a column corre-
sponds to an incline percentage.
B MESSAGE CENTER: This window displays step-by-step instructions for setting up a work-
out. During a workout, it displays calories, distance, time, incline and speed. Additionally,
the MESSAGE CENTER displays calories per hour, METS, Watts, pace in minutes per
mile/kilometer, and distance climbed, if enabled to do so in the Managers Configuration.
See Section 5.1, titled Entering and Using the Managers Configuration.
C TIME, INCLINE, and SPEED ARROW keys: Press these keys to increase or decrease the
workout time, the incline of the treadmill deck, or the striding belt speed.
17
D CLEAR key: Press this key once to clear data not yet entered. Press twice in succession,
while programming, to reset the treadmill and restart the programming sequence.
ENTER key: Press this key to confirm entries of workout setup values, as displayed in the
MESSAGE CENTER.
E WORKOUT SELECTION ARROW keys: When setting up a workout, use these keys to
scroll through workout options as they appear in the MESSAGE CENTER. Also, use these
keys set up workout or Managers Configuration options.
F QUICK START: Press this key to begin a manual workout immediately, without having to
select a workout program. Once the workout is in progress, use the ARROW KEYS to
change the intensity level or workout duration as desired.
COOL DOWN: Press this key to begin an automatically customized workout cool-down.
PAUSE: Press this key to stop the belt and hold the current workout. Continue the workout
by pressing the ENTER key. The workout also resumes automatically when the maximum
pause duration is reached.
The Life Fitness Treadmill is equipped with a manual emergency stop system. Use either of the
two features described below to stop the treadmill immediately.
An octagon-shaped STOP button is located on a panel below the display console. A cord with a
clothing clip is attached to this button. Before starting a workout, attach the clip to clothing. To
stop the striding belt on the treadmill, pull the cord. Replace the key to reset the system.
A rectangular STOP key is located on the panel as well. Press the key to stop the striding belt
and end the current workout.
18
2.3 READING RACK
The display console design includes a built-in reading rack allowing a book or magazine to be
supported during the workout.
2.4 ACCESSORY TRAYS
The accessory trays, located on either side of the display console, are removable. They should
be cleaned periodically. See Chapter 6, titled Service and Technical Data, for details.
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Life Fitness Exercise Bike Lifecycle 9100 Mode d'emploi

Catégorie
Fitness, gymnastique
Taper
Mode d'emploi