Frigidaire FGC30S4AQB Le manuel du propriétaire

Marque: Frigidaire

Modèle: FGC30S4AQB

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

Ce manuel convient également à

Visit the Frigidaire Web Site at:

http://www.frigidaire.com

CONTENTS Page

Versi6nen espafiol ...........................................................2

ProductRegistration ........................................................2

Important Safety Instructions ......................................3-4

Grounding Instructions ....................................................4

LiquefiedPetroleum (Propane)GasConversion...............5

FlameSize.........................................................................5

Proper BurnerAdjustment ................................................5

Setting Surface Control

Venturi (open) Burner Models .....................................6

SealedBurner Models ..................................................6

Electric Ignition ...........................................................6

SelectingSurface Cooking Utensils..................................7

SpecialtyPans& Trivets ...................................................7

CanningTips & Information .............................................8

GeneralCleaning

CleaningVarious Parts of your Cooktop......................9

Venturi (open) Burner Models ...................................10

SealedBurner Models ..........................................11-14

Avoid ServiceChecklist ..................................................15

Warranty.........................................................................16

READ AND SAVE THESE INSTRUCTIONS 318200657 (0111) Rev. C

Product Registration

The PRODUCT REGISTRATION CARD

should be filled in completely, signed

and returned to Electrolux Home

Products North America.

Versibn en espafiol

Sidesea obtener una copia en espahol de

este Manual del Usuario, s[rvaseescribir a

la direcci6n que seincluye a continuaci6n.

Solicite la P/N 318204005.

SpanishOwner's Guides

Electrolux Home Products North America

Consumer Relations

P.O. Box212378

Augusta, Georgia

30917-2378

Thank you for choosing this appliance. The information contained within this

Owner's Guide will instruct you on how to properly operate and care for your

cooktop. Pleaseread through the information contained in your literature pack to

learn more about your new appliance.

Record Your Model and Serial Numbers

Recordin the space provided belowthe model and serialnumbers found underneath

or inside the cooktop.

Model Number:

Serial Number:

Date of Purchase:

This Owner's Guide contains general operating instructions for your cooktop and

feature information for severalmodels. Your cooktop may not haveallthe described

features.

Note: The instructions appearing inthis Owner's Guide arenot meant to cover every

possible condition and situation that may occur. Common sense and caution must

be practiced when installing, operating and maintaining any appliance.

If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

FOR YOUR SAFETY:

m Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone

in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, servicer or the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

Save these instructions for future reference.

This guide contains important safety symbols and instructions. Pleasepay special attention to these symbols and follow all

instructions given. Here isa brief explanation of the use of these symbols.

This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.

This symbol will help alert you to situations that may cause bodily injury or property damage.

• Remove all tape and packaging wrap before using the

cooktop. Destroy the carton and plastic bags after unpacking

the cooktop. Neverallow children to play with packaging material.

Do not remove the model/serial plate attached to the cooktop.

• Proper Installation--Be sure your appliance is properly

installed and grounded by a qualified technician in accordance

with the National Fuel Gas Code ANSI Z223.1 latest edition in

the United States, or in Canada CAN/CGA B149.1, and CAN/

CGA B149.2, and the National Electrical Code ANSI/NFPA No.

70--latest edition in United States, or in Canada CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local code

requirements. Install and/or adjust only per installation

instructions provided in the literature package for this cooktop.

Ask your dealer to recommend a qualified technician and an

authorized repair service. Know how to shut off gas supply at the

meter and disconnect the electrical power to the cooktop at the circuit

breaker or fuse box in case of an emergency.

• User Servicing--Do not repair or replace any part of the

appliance unless specifically recommended inthe manuals. All

other servicing should be done only by a qualified technician. This

may reduce the risk of personal injury and damage to the cooktop.

• Never modify or alter the construction of a cooktop by

removi ng pa nels, wire covers, or any other part of the prod uct.

Stepping or leaning on this cooktop can result

in serious injuries and may also cause damage to the cooktop. Do

not allow children to climb or play around the cooktop.

• Storage on Appliance--Flammable materials should not be

stored on the cooktop, near surface burners. This includes

paper, plastic and cloth items, such ascookbooks, plasticware and

towels, aswell as flammable liquids. Do not store explosives, such

asaerosol cans, on the cooktop. Flammable materials mayexplode

and result in fire or property damage.

r__=_J_ Do not store items of interest to children in the

cabinets above the cooktop.

• Do not leave children alone--Children should not be left alone

or unattended in the area where an appliance is in use. They

should never be allowed to sit or stand on any part of the appliance.

• DO NOT TOUCH SURFACE BURNERS, GRATES, OR AREAS

NEARTHESE BURNERS. Surface burners may be hot eventhough

the flames are not visible. Areas near surface burners may become

hot enough to cause burns. During and after use, do not touch or

let clothing or other flammable materials touch these areas until

they have had sufficient time to cool. Among these areas are the

cooktop and the surfaces facing the cooktop.

• Wear Proper Apparel--Loose-fitting or hanging garments

should never be worn while using the appliance. Do not let

clothing or other flammable materials contact hot surfaces.

Never use your appliance for warming or

heating the room.

• Do Not Use Water or Flour on Grease Fires--Smother the fire

with a pan lid, or use baking soda, a dry chemical or foam-type

extinguisher.

• When heating fat or grease, watch it closely. Fat or grease may

catch fire if allowed to become too hot.

UseOnly Dry Pot holders--Moist or damp pot holders on hot

surfaces may result in burns from steam. Do not let the pot

holders touch the flame or burners. Do not use a towel or other

bulky cloth instead of a pot holder.

Do Not Heat Unopened Food Containers--Buildup of pressure

may cause container to burst and result in injury.

Know which knob controls each surface burner. Always turn the

knob to the LITEposition when igniting the burners. Visually check

that the burner has lit. Then adjust the flame soit does not extend

beyond the edge of the utensil.

Use Proper Flame Size--Adjust flame size so it

does not extend beyond the edge of the utensil. The use of

undersized utensils will expose a portion of the burner flame to direct

contact and may result in ignition of clothing. Proper relationship of

utensil to flame will also improve efficiency.

Do not use stove top grills on your sealed gas

burners. If you use a stove top grill on a sealed gas burner, it will

cause incomplete combustion and can result in exposure to carbon

monoxide levels above allowable current standards. This can be

hazardous to your health.

Use proper pan size--This appliance is equipped with one or

more surface burners of different sizes. Select utensils having flat

bottom large enough to cover the surface burner. The use of

undersized utensils will expose a portion of the surface burner to

direct contact and may result in ignition of clothing. Proper

relationship of utensil to the surface burner will also improve

efficiency.

Utensil Handles Should Be Turned Inward and Not Extend

Over Adjacent Surface Burners--To reduce the risk of burns,

ignition of flammable materials, and spillage due to unintentional

contact with the utensil, the handle of the utensil should be

positioned so that it is turned inward, and does not extend over

adjacent surface burners.

IMPORTANT SAFETY INSTRUCTIONS (continued)

• Never Leave Surface Burners Unattended at High Heat

Settings--Boilovers cause smoking and greasy spillovers that

may ignite, or a pan that has boiled dry may melt.

• Protective Liners--Do not use aluminum foil to line surface

burner pans. Protective liners or aluminum foil may interfere with

heat and air distribution, and combustion. Damage to the

cooktop or personal injury may result.

• Glazed Cooking Utensils--Only certain types of glass, glass/

ceramic, ceramic, earthenware, or other glazed utensils are

suitable for cooktop servicewithout breaking due to the sudden

change in temperature. Check the manufacturer's

recommendations for cooktop use.

Do Not Use Decorative Surface Burner Covers. If a burner is

accidentally turned on, the decorative cover will become hot and

possibly melt. You will not be able to see that the burner is on.

Burns will occur if the hot covers are touched. Damage may also

be done to the cooktop or burners becausethe covers may cause

overheating. Air will be blocked from the burner and cause

combustion problems.

GLASS COOKTOPS (somemodels):

• Do Not Operate or Clean a Broken Cooktop Glass--if glasstop

should break, cleaning solutions and spillovers may penetrate the

broken cooktop and create a risk of electric shock. Contact a

qualified technician immediately.

Clean Cooktop Glass with Caution--If awet sponge or cloth is

usedtowipe spillson ahot cooking area, be carefulto avoid asteam

burn. Some cleaners can produce harmful fumes if applied to ahot

surface.

• Do Not Place Hot Cookware on the Cooktop Glass. This could

cause glass to break.

= Avoid scratching the cooktop glass with sharp objects.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances

known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential

exposure to such substances.

SAVE THESE INSTRUCTIONS

Grounding Instructions (electric ignition models only)

IMPORTANT: READAND SAVETH ESEINSTRUCTIONS.

Thisappliance isequipped with a 3 prong grounding plug for your

protection against shock hazard and should be plugged directly into a properly

grounded receptacle. DO NOTcut or removethe grounding prong from this plug.

Forpersonal safety, this cooktop must be properly grounded. Formaximum safety,

the power cord must be plugged into a 120Vi60 Hz. outlet that is correctly

polarized and properly grounded.

If a two-prong wall receptacle is the only available outlet, it is the personal

responsibility of the consumer to have it replaced with a properly grounded three-

prong wall receptacle installed by a qualified electrician.

DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD ROUND

GROUNDING PRONG FROM THE POWER CORD PLUG. SEETHE INSTALLATION

INSTRUCTIONS PAC KAGED WITH THIS COO KTOP FORCOMPLETE INSTALLATION

AND GROUNDING INSTRUCTIONS. DO NOT OPERATE THE COOKTOP USING A

TWO-PRONG ADAPTER OR AN EXTENSION CORD.

Avoid fire hazard or

electrical shock. Do not use an adaptor

plug, an extension cord, or remove

grounding prong from electrical power

cord. Failure to follow this warning can

cause serious injury, fire or death.

Grounding

type wall

receptacle

Power supply cord with

3-prong grounding plug

Liquefied Petroleum (Propane) Gas Conversion

Severe shock or damage to the cooktop may occur if the cooktop is not installed by a qualified installer or

electrician.

This appliance can be usedwith Natural Gasand Propane Gas. It isshipped from the factory for usewith natural gas.

If you wish to convert your cooktop for usewith Liquefied Petroleum (propane) gas:

Models with Venturi (open) Burners, seethe installation instructions guide for the conversion instructions.

Models with Sealed Burners:

- Forsome of them, you should order the conversion kit from your local dealer or from an authorized serviceagency (see

Warranty). Seethe installation instructions for the conversion kit number.

- Forothers, the conversion kit isincluded in the packaging, ifyou wish to convert your cooktop for usewith propane gas,

usethe supplied fixed orifices located in the package containing the installation instruction, in a bag marked "FOR LP/

PROPANEGAS CONVERSION". Follow the instructions packaged with the orifices (for models with sealed burners only).

Theconversion must be performed bya qualified servicetechnician in accordance with the manufacturer's instructions and all codes

and requirements of the authority having jurisdiction. Failure to follow the instructions could result in serious injury or property

damage. The qualified agency performing this work assumes responsibility for the conversion.

Flame Size

For most cooking, start on the highest control setting and then turn to a lower one to

complete the process. Usethe chart below as a guide for determining proper flame size for

various types of cooking. The size and type of utensil used and the amount of food being

cooked will influence the setting needed for cooking.

For deep fat frying, usea thermometer and adjust the surface control knob accordingly. If

the fat istoo cool, the food will absorb the fat and be greasy.If the fat istoo hot, the food will

brown so quickly that the center will be undercooked. Do not attempt to deep fat fry too

much food at once asthe food will neither brown nor cook properly.

*Flame size

High Flame

Medium Flame

Low Flame

Type of Cooking

Start most foods; bring water to a boil; pan broiling.

Maintain a slow boil; thicken sauces, gravies; steam.

Keep foods cooking; poach; stew.

* These settings are based on using medium-weight aluminum pans with lids. Settings

may vary when using other types of pans.

Never extend the flame

beyond the outer edge of the

utensil. A higher flame simply

wastes heat and energy, and

increases your risk of being

burned by the flame.

WRONG

Proper Burner Adjustments

The color of the flame isthe key to proper burner adjustment. A good flame isclear, blue and hardly visible in a well-lighted room.

Eachcone of flame should be steady and sharply defined. Adjust or clean burner if flame isyellow-orange. To clean burner, see

instructions under General Cleaning.

Setting Surface Controls

The surface control knobs shown below

may not look identical to the Surface Corn

trois Knobs on your range; They are only

representational.

Venturi (opened) Burner Models

To Adjust Low or "Simmer" Setting (some models)

The burner flame, at low setting, can be adjusted if it istoo high or too low; refer to

the installation instruction for adjustment procedure.

To Adjust Standing Pilot Model (some models)

Eachburner lights automatically either an electric or a standing pilot, depending

on your model. Standing pilots must be lit initially. To light the standing pilot, open

gas supply on pilot shutoff valves (screw), lift the cooktop from the front edge and

hold a match near the pilot. Standing pilots will remain lit when the burners are

turned off; because of that, the porcelain enamel cooktop can be hot even if

burners are not used; refer to Installation Instructions for proper pilot adjustment.

Models with electric ignitors light automatically each time a control knob isturned

to the LITEposition.

To operate the Surface Burner:

1. Placecooking utensil on burner.

2. Pushin and turn the Surface Control knob to LITE.Note: All electronic ignitors

will click atthe sametime. However, onlythe burner you are turning on will ignite.

3. Visually check that the burner has lit.

4. After the burner lights,turn the control knob tothe desired flame size.Thecontrol

knobs do not have to be set at a particular mark. Usethe guides and adjust the

flame asneeded. DO NOT cook with the control knob in the LITEposition. (The

electronic ignitor will continue to click if left in the LITEposition.)

Sealed Burner Models

Your appliance may be equipped with any combination of the following burners:

Simmer Burner, this burner is best used for simmering delicate sauces, etc.

Standard Burner, can be used for most all surface cooking needs.

Large Burner, the larger burner isbest usedwhen bringing large quantities of liquid to temperature and when preparing larger

quantities of food.

Regard_ess_fsize,a_waysse_ectautensi_thatissuitab_ef_rtheam_untandtype_ff__dbeing The surface control knobs

prepared. Selecta burner and flame size appropriate to the pan. Never allow flames to extend shownbelowmaynotlookidem

beyond the outer edge of the pan. tical to the Surface Controls

Eachburner lights automatically from an electric ignitor each time a control knob isturned to Knobson your range;Theyare

the lite position, only representational.

To operate the surface burner:

1. Placecooking utensil on burner.

2. Push in and turn the Surface Control knob to LITE.Note: All electronic ignitors will click

at the same time. However, only the burner you are turning on will ignite.

3. Visually check that the burner has lit.

4. After the burner lights, turn the control knob to the desired flame size.The control knobs

do not haveto be set at a particular mark. Usethe guides and adjust the flame asneeded.

DO NOT cook with the control knob inthe LITEposition. (Theelectronic ignitor will continue

to click if left inthe LITEposition.)

5. Toturn the burner off, turn the control knob asfar as it ill go, to the OFFposition.

Electric Ignition Models

Inthe event of an electrical power outage, the surface burners can be lit manually. To light a surface burner, hold a lit match to

the burner head, then slowly turn the surface control knob to LITE.Usecaution when lighting surface burners manually.

Surface burner in usewhen an electrical power failure occurs will continue to operate normally.

Do not operate the burner for an extended period of time without cookware on the grate. The finish on

the grate may chip without cookware to absorb the heat.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top

of the cooktop when it isin use. These items could melt or ignite. Pot holders, towels or wood spoons could catch fire if placed

too close to a flame. 6

Selecting Surface Cooking Utensils

For best results and energy conservation, choose cooking utensils that have these characteristics:

Pansshould haveflat bottoms. Check for

flatness by rotating a ruler acrossthe bot-

tom. There should be no gaps between

the pan and ruler.

Note: Always usea utensil for its intend-

ed purpose. Follow manufacturer's in-

structions. Some utensils were not made

to be usedin the oven or on the cooktop.

Note: Do not usegriddle over more than

one burner. That can damage your

cooktop and that can result in exposure

to carbon monoxide levels above allow-

able current standards. That can hazard-

ous to your health.

*GOOD

• Flat bottom and straight sides.

• Tight fitting lids.

• Weight of handle does not tilt

pan. Pan is well balanced.

• Pansizes match the amount of

food to be prepared.

• Made of material that conducts

heat well.

• Easyto clean.

POOR

• Curved and warped pan bottoms.

• Panoverhangs unit by more than

2.5 cm (1").

• Heavy handle tilts pan.

• Flameextends beyond unit.

* Specialty pans such as lobster pots, griddles and pressure cookers may be used

but must conform to the above recommended cookware requirements.

Specialty Pans & Trivets

Woks with flat bottoms suitable for

use on your cooktop are available in

most cookshop or hardware stores.

Round-bottomed woks (with a

support ring that does not extend

beyond the burner unit) may also be

used. The metal ring was designed to

support the wok safely when it is

filled with large amounts of liquids

(soup making) or fat (frying).

DO NOT use a wok if it is equipped

with a metal ring that extends

beyond the burner unit. Because this

ring traps heat, the surface unit and

cooktop surface could be damaged.

Wire trivets: Do not usewire trivets. Cookware bottoms must be in direct contact

with the grates.

DO NOT use two burner units to heat one large pan such as a

roaster or griddle, or allow cooking utensils to boil dry. The bottom surface of the

pan in either of these situations could cause discoloring or crazing of the appliance

cooking surface, and damage to the grates and burner units.

Canning Tips &

Information

Canning can generate

largeamounts of steam. Useextreme cau-

tion to prevent burns. Always raise the

lid to vent steam away from you.

_--;,

1. Usetested recipes and follow instructions carefully. Check with your local

Cooperative Agricultural Extension Service or a manufacturer of glassjars for

the latest canning information.

2. Useflat-bottomed canners only. Heat isspread more evenly when the

bottom surface isflat.

3. Center canner on the burner grate.

4. Start with hot water and a high heat setting to reduce the time it takes to

bring the water to a boil; then reduce the heat setting as low as possible to

maintain a constant boil.

5. It isbest to can small amounts and light loads.

Prevent damage to cooktop and burner grates:

1. Do not usewater bath or pressure canners that extend more than one inch

beyond the edge of the burner grate.

2. Do not leave water bath or pressure canners on high heat for an extended

amount of time.

3. Alternate surface units between each batch to allow the units and

surrounding surfaces to cool down. Tryto avoid canning on the same burner

unit all day.

Safecanning requires that harmful micro-organisms are destroyed

and the jars are sealed completely. When canning in a water bath canner, a gentle

but steady boil must be maintained continuously for the required time.

General Cleaning

Cleaning Various Parts of Your Cooktop

Before cleaning any part of the cooktop, be sure all controls are turned OFFand the cooktop is COOL. Remove spillovers and

heavy soiling as soon as possible. Regular cleaning will reduce the number of major cleaning later.

Surfaces How to Clean

Aluminum (Trim Pieces) & Use hot, soapy water and a cloth. Dry with a clean cloth.

Vinyl

Glass, Painted and Plastic

Control Knobs, Body

Pieces, and Decorative Trim

Control Panel

Stainless Steel, Chrome

Decorative Trim

Porcelain Enamel

Burner Grates, Burner Pans

(some models), Burner Rings

(some models), Cooktop

Surface

Surface Burners

For general cleaning, use hot soapy water and a cloth. For more difficult soils and built-up

grease, apply a liquid detergent directly onto the soil. Leaveon soil for 30 to 60 minutes.

Rinsewith a damp cloth and dry. DO NOT useabrasive cleaners on any of these materials;

they can scratch.

Before cleaning the controlpanel, turn all controls to OFFand remove the control knobs. To

remove, pull each knob straight off the shaft. Clean using hot, soapy water and a cloth. Be

sure to squeeze excess water from the cloth before wiping the panel; especially when

wiping around the controls. Excesswater in or around the controls may cause damage to

the appliance. To replace knobs after cleaning, line up the flat sides of both the knob and

the shaft; then push the knob into place.

Gentle scouring with a soapy nylon pad will remove most spots. Rinsewith a 1:1 solution of

clean water and ammonia. Cover difficult spots with an ammonia soaked paper towel for

30 minutes, scrub with a nylon pad and rinse with clean water. Cleaners made especially for

stainless steel or chrome are recommended. Bluish stains on these materials are caused by

overheating and cannot be removed. Remove all cleaners or the finish may be damaged

during future heating. DO NOT use spray oven cleaners on the cooktop.

Gentle scouring with a soapy nylon pad will remove most spots. Rinsewith a 1:1 solution of

clean water and ammonia. If necessary, cover difficult spots with an ammonia-soaked

paper towel for 30 to 40 minutes. Rinsewith clean water and damp cloth, then scrub with

a soap-filled scoring pad. Rinseand wipe dry with a clean cloth. Remove all cleaners or the

porcelain may become damaged during future heating. DO NOT use spray oven cleaners

on the cooktop.

The holes in the burners of your cooktop must be kept clean at all times for proper ignition

and a complete, even flame. Clean the burner holes routinely with a small gauge wire or

needle and especially after bad spillovers which could clog these holes.

To remove and replace burner units per your model, see instructions under General

Cleaning. To clean, soak the burners in a 1:1 solution of ammonia and water for 30 to 40

minutes. For stubborn stains, scrub with soap and water or a mild abrasive cleanser and

damp cloth. Dry the burners thoroughly in a warm oven for 30 minutes. Then replacethem,

making surethey are seated and level. DO NOT wash burner units in the dishwasher.

General Cleaning (continued)

Venturi (open) Burner Models (somemodels)

To Raise and Lower the Top for Cleaning

The cooktop ishinged and can be raisedto clean the area underneath. Be sureall cooktop controls are turned to OFFand burner

grates are cool.

1. Removecontrols knobs, burner grates and spillover bowls. Set aside.

2. Grasp the front of the cooktop and lift. Some models have a swing-up rod to support the cooktop in its raised position.

3. Clean underthe cooktop.

4. Lower the top gently after lowering the support rod (some models).

5. Replace bowls, grates and control knobs.

When lowering the top, grasp the sides with fingertips only. Becareful not to pinch fingers. Also, DO NOT drop

or bend the cooktop when raising or lowering. This could damage the surface.

DO NOT turn on the burners when the cooktop israisedfor cleaning. Be surethat the top iscompletely lowered

and securely in place before turning on the burners.

To Remove and Replace Burners

The burners on your cooktop maybe removed for cleaning. Be sure all controls are turned to OFFand burner grates are cool

before removing cooktop burner units.

To Remove Burners

1. Removethe shipping screws from the support bracket. Seeillustrations for location of

screws.

2. Graspthe burner head and tilt it to the right to releasethe tab from the burner support

(A in Figure 1).

3. Lift the end of the burner assembly.Then pull away from the front of the cooktop to

free the air shutter from the gasvalve orifice (B in Figure 1).

If your cooktop isequipped with a standing gas pilot, usecaution when removing burner.

The flash tube may be hot because it is located near the pilot.

Check the lighter and burner ports (Figure 2). If they are clogged, usea wire or needle to

clear them.

Shipping

Screw

Figure 1

Gas Valve

Burner Orifice

Support

,b Air Shutter

To remove burned-on food, soak the burners in a vinegar and water solution for

20-30 minutes. Forstubborn stains, scrub with soap and water or a mild abrasive cleanser

and a damp cloth. Do not wash burners in a dishwasher.

To Replace Burners

1. Slide the air shutter over the gas valve orifice (Figure 1).

2. Lower the burner assembly and hook the tab in the slots in the burner support. Make

sure it is properly seated and level.

3. Be sure both tabs are in the correct slots, the burner sits level and straight, and the

flash tube forms a straight line from the igniter to the burner (Figure 2).

4. Replaceshipping screws if desired. These screws are not necessary for the operation

of the burner. They stabilize the burner during shipping of the appliance. Retain the

screws for later use in the event the range is moved.

Figure 2

.Burner Ports Shipping

/ __ Screws

_ Flash Tube

Lighter Port

Burner Support Pilot or Igniter

General Cleaning (continued)

Sealed Burner Models (some models)

Unlike the standard gas range, THIS COOKTOP ISNOT REMOVABLE. Do not attempt to remove or lift the cooktop.

Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop isCOOL.

DO NOT use a cooktop cleaner on a hot cooktop. The fumes can be hazardous to your health, and can

chemically damage the ceramic- glass surface. Be sure the controls are turned to OFF. Do not use commercial oven

cleaners on any part of the cooktop. Damage to the finish or parts could result.

To Clean the Tempered-glass Cooktop (some models)

The cooktop isdesigned to make cleaning easier. Becausethe four burners are sealed, cleanups are

easywhen spillovers are cleaned up immediately. To clean, wipe with a clean, damp cloth and wipe

dry.

Correct and consistent cleaning isessential to maintaining your heat-resistant glass top. Spills and

spatters should be wiped up using a clean paper towel and sudsywater. This should be done either

as soon as possible after spill occurs, after cooking iscompleted, or at the latest, before using the

cooktop again. Usecaution if the cooktop ishot. Forheavy spills, spatter or burned-on materials, use

razor blade scraper. Hold the razor blade scraper at a 30° angle and remove food spills or burned on

food residue.

For sugary spillovers:

Sugaryspills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills

while the cooktop is still hot.

Finish the deaning process by applying a recommended heat- resistant glass cooktop cleaning

cream. Apply cleaner with clean, damp paper towel. Rinse with a paper towel dampened with clean

water and wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner residue.

witharazorbladescraper.Use

cautionto avoiddamaging

surface.

Do NOT use the following on the heat-resistant glass cooktop:

- Abrasive plastic, nylon, metal scouring or cloth pads. They may scratch the cooktop and make it more difficult to clean later.

Always usea new, clean paper towel when cleaning the heat-resistant glasstop.

- Anything that may melt (plastics, aluminum foil, sugar or food with a high sugar content).

- Heavy duty cleansers, rust or stain removers.

- Chlorine bleach, ammonia, hydrofluoric acid or any other kind of chemical cleaners. They may etch or discolor the cooktop.

- Sponges, cloths or dish towels. Always usea new, clean paper towel when cleaning the cooktop. Lint or soil remaining on the

cooktop from a cloth or sponge can burn and cause discoloration.

To Clean the Ceramic-glass Cooktop (some models)

The cooktop isdesigned to make cleaning easier. Cleanups are easy when spillovers are

cleaned up immediately. To clean, wipe with a clean, damp cloth and wipe dry.

Correct and consistent cleaning isessential to maintaining your heat-resistant glass top. Spills

and spatters should be wiped up using a clean paper towel and sudsy water. This should be

done either as soon as possible after the spill occurs, after cooking iscompleted, or at the latest,

before using the cooktop again. Use caution if the cooktop is hot. For heavy spills, spatter or

burned-on materials, use a razor blade scraper. Hold the razor blade scraper at a 30° angle and

remove food spills or burned on food residue.

For sugary spillovers:

Sugaryspills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills

while the cooktop is still hot.

Finish the cleaning process by applying a recommended heat-resistant glass cooktop cleaning

cream. Apply cleaner with clean, damp paper towel. Rinsewith a paper towel dampened with

clean water and wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner

residue.

witharazorbladescraper.Use

cautionto avoiddamaging

surface.

General Cleaning (continued)

Sealed Burner Models (some models) (continued)

To Clean the Ceramic-glass Cooktop (somemodels)(continued)

Special Caution for Aluminum Foil and Aluminum Cooking Utensils

1) Aluminum foil

Use of aluminum foil will damage the cooktop. Do not use under any circumstances.

2) Aluminum utensils

The melting point of aluminum being much lower than that of other metals, care must betaken when aluminum pots or pans

are used. If allowed to boil dry, not only will the utensil be ruined, but also permanent damage in the form of breakage, fusing

or marking may affect the ceramic glass surface.

Things to Remember

1. Do not slide utensils across cooktop surface in any circumstance, doing so may scratch or _

metalmark the cooktop surface.

2. Avoid using bleach and do not use ammonia to clean the ceramic surface.

3. Do not put plastic items on warm cooking areas.

4. Never slide oven racks across cooktop surface. They may scratch or metalmark the cooktop.

5. If cooktop should break, do not usecooktop or attempt to clean it. Call your SearsService Center immediately.

6. Never use rivet or metal stand between the cooking utensil and the ceramic cooktop. The ceramic surface may be

scratched, metal marked or etched by such items.

7. Sugary spills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills while the cooktop is

still hot. Usecaution when following the steps below.

a) Turn off all surface units and remove all pans immediately.

b) Wearing an oven mitt, usea razor to scrape the hot spill out of the cooking zone to cooler area on the cooktop.

c) Allow the cooktop to cool.

Use and Care of Glass Surface

Problem Cause To Remove

Fine "brown

lines" (tiny

scratches or

abrasions which

have collected

soil)

Metal marking

(mark or black

marks).

Brown streaks

and specks.

Coarse particles (salt,

sand, sugar or grit)

between bottom of

cookware and cooktop

that are not removed

before cooking.

Using incorrect cleaning

materials.

Sliding or scraping

metal utensils or oven

shelves across cooktop.

Cleaning with a

sponge or dishcloth

that has been used

for other kitchen tasks.

To Prevent

Clean cooktop after

every use.

Daily use of cleaner

creme.

Do not slide cookware

across cooktop.

Use cleaner creme

with clean, damp paper

towel.

Tiny scratches are not removable.

They can be minimized by

continual use of cleaner creme.

Such scratches do not affect

cooking.

Apply cleaner creme

with dampened paper

towel to a cooled surface.

Use a small amount of cleaner

creme with clean, damp paper

towel.

NOTE: Due to the high intensity of heat generated by the surface elements, the glass surface will turn green when the element

will be turned off. This phenomenon is normal and the glass will come back to its original white color after it has completely

cooled down. (White glasscooktops only).

General Cleaning (continued)

Sealed Burner Models (some models) (continued)

To Clean the Ceramic-glass Cooktop (somemodels)(continued)

Use and Care of Glass Surface (continued)

Cleaning Materials for Ceramic-Glass Cooktop

Somecleaning materials may contain an ingredient which can damage the cooktop. Use recommended cleaning products only

(see below). Cleaner cream should be used regularly. First use recommended products listed below, then use cleaner cream.

Useonly recommended cleaning products and follow these basic cleaning suggestions.

1. Before the cooktop is used, thoroughly clean and saturate the cooktop with cleaner cream.

a) Dampen clean paper towel and clean unit.

b) Wipe off with another clean, damp paper towel; then wipe dry.

2. For normal daily cleaning, apply a dab of cleaner cream in the center of each unit-area to be cleaned. Start with

approximately 1/8 teaspoon (apply more if needed). Then, proceed as stated above in a and b.

3. Make sure bottom of cookware and cooking area are clean and dry.

4. Select heat settings and cookware large enough for food and liquid.

5. Wipe up food spills and spatters before they burn into surface.

IMPORTANT: Regularly use cleaner cream. If you run out of cream, use one of the cleaners listed. Be sure to get a new supply

of cleaner cream.

Never mix cleaning products! Mixtures may interact, with damaging or hazardous results.

Do Use on Ceramic Glass Cooktop

1. Baking soda.

2. Nonqmpregnated plastic and nylon pads.

3. For burned on material, scrape with single-edged razor blade, held at a 30° angle.

4. Ceramic glass cleaning cream.

Do not use on ceramic-glass cooktop

1. Avoid pads, that can leave marks and scratches.

2. Avoid heavy-duty cleaning powders; these can scratch, depending on their abrasiveness and cleaning pressure applied.

3. Avoid chemical oven cleaners. These can etch the cooktop surface and are caustic.

4. Avoid rust stain removers containing hydrofluoric acid.

5. Avoid using bleach and do not useammonia.

Special Cleaning Instructions for Mineral Deposits and Discolorations

Problem: A gray brown stain that is not removed when using cleaner creme.

Cause: Condensation, when cooking, often collects and drips from cookware. The minerals found inwater supply and foods may

cause a gray or brown film to develop on cooktop. This film issothin it cannot be felt and appears to be under cooktop.

To Prevent: Daily and proper use of cleaner creme.

To Remove: - Wet surface with water and sprinkle on cleaner creme.

- Scrub with clean, damp paper towel until stain disappears.

- Clean remaining paste away with damp paper towel.

- Apply dab of cleaner creme and polish with a clean paper towel.

WARNING

- Do not use cleansers on a heated surface. Fumescould be hazardous. Wait for area to cool before cleaning.

- Do not usecleaner creme to clean porcelain, paint or aluminium.

General Cleaning (continued)

Sealed Burner Models (some models) (continued)

To Clean the Burner Grates, Contoured Burner Pans, Burner Cap and Burner Base

Theburner grates,contoured burner pans, burner capsand burner baseshould be routinely cleaned. Keeping the burner ports clean

will prevent improper ignition and an uneven flame. Seeinstructions below.

To Clean the Burner Grates

Besure burners and grates are cool before you place your hand, a pot holder,

cleaning cloths or other material on them. Thecastiron burner gratescan bewashed

in hot soapywater. Rinsethoroughlyand drythe grateswith acloth- don't putthem

on the cooktop while still wet. Be sure the grates are positioned securely over the

burners.

To remove burned on food, placethe grates in a covered container or plastic bag.

Add 1/4 cup ammonia and soak for 30 minutes. Wash, rinse well and dry. An

abrasive cleaner can be used for stubborn stains. Burner grate can appear in different shapes.

To Clean the Contoured Burner Pans

The burner pans are attached to the cooktop and are not removable. The burner pan forms a recessedwell area located around

each burner unit. If spill occurs in one of the well areas, blot up spill with an absorbent cloth. Rinsewith aclean, damp cloth and

wipe dry.

Sealed Burner

Burner Cap

To Clean the Burner Cap

Remove burner cap. Usesoap-filled pad or mild abrasive cleanser to clean burner

caps. If necessary,cover stubborn spots with an ammonia-soaked paper towel for

30 minutes. Rubgentlywith a mixture of cleanwater and vinegar. Wipe dry. Remove

all cleaners or the porcelain may become damaged during future heating.

To Clean the Removable Burner Baseand Gas Opening (some models)

The ports (or slots)around the burner basemust be routinely cleaned. Useasmall-

gauge wire or needle to clean small slots or holes.

Note: Ifthe electrode isdamaged or broken, the surface burner will not light because

it will not spark. Manual lighting with a match isstill possible.

For proper flow of gasand ignition of the burner - DO NOTALLOW SPILLS,FOOD,

CLEANING AGENTS OR ANY OTHERMATERIAL TO ENTERTHE GAS OPENING

TUBE.Gasmust flow freelythrough the small hole in the brassorifice for the burners

to light properly. If the gasopening orifice becomes soiled or clogged, usea small-

gauge or needle to clean. ALWAYS keepthe burner capin placewhenever asurface

burner isin use.

To Replace the Burner Base and the Burner Cap

Make sure the pieces are thoroughly dry before placing back.

1. Replace burner baseand burner cap at there place. Make sure each burner cap

and burner baseare properly aligned and leveled.

2. Replace the burner grate.

3. Turn the burner on to determine if it light. If the burner does not light after

cleaning, contact an authorized servicer. Do not service the sealed burner

yourself.

Avoid Service Checklist

Beforeyou call for service, review this list. It may save you time and expense. The list includes common occurrences that are not

the result of defective workmanship or materials in this appliance.

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Surface burners do not light.

Surface Control knob hasnot been completely turned to LITE.Push in and turn the

Surface Control knob to LITEuntil burner ignites and then turn control to desired

flame size.

Be sure gas supply valve isopen.

Gas-air mixture needsa straight line to travel. Besure burner isproperly seated in its

support (models with open burners only).

Burner ports or slots are clogged. With the burner off, usea small-gauge wire or

needle to clean ports or slots.

Power cord is disconnected from outlet (electric ignition models). Be sure cord is

plugged securely into outlet.

Electrical power outage (electric ignition models). Burners can be lit manually. See

Setting Surface Controls in this Owner's Guide.

Surface burner flame burns half way

around.

Burner ports or slots are clogged. With the burner off, clean ports with a small-

gauge wire or needle to clean ports or slots.

Moisture ispresent after cleaning. Lightly fan the flame and allow burner to operate

until flame isfull. Dry the burners thoroughly following instructions under General

Cleaning.

Surface burner flame isorange.

Dust particles in main line. Allow the burner to operate a few minutes until flame

turns blue.

In coastal areas, a slightly orange flame is unavoidable due to salt air.

Scratches or abrasion on cooktop

surface.

Coarse particles such as salt or sand between cooktop and utensil can cause

scratches. Besure cooktop surface and bottoms of utensils are clean before usage.

Small scratches do no affect cooking and will become lessvisible with time.

Cleaning materials not recommended for ceramic-glass cooktop have been used.

See "To Clean the Ceramic-glass Cooktop" section under General Cleaning.

Cookware with rough bottom hasbeen used. Usesmooth, fit-bottomed cookware.

Metalmarks.

Sliding or scraping of metal utensils on cooktop surface. Do not slide metal utensils

on cooktop surface. Useceramic-glasscooktop cleaning cream to remove the marks.

See "To Clean the Ceramic-glass Cooktop" section under General Cleaning.

Brown streaks or specks. Boilover are cooked onto surface. Use razor blade scraper to remove soil. See "To

Clean the Ceramic-glass Cooktop" section under General Cleaning.

Areas of discoloration with metallic

sheen.

Mineral deposits from water and food. Remove using a ceramic-glass cooktop

cleaning cream. Use cookware with clean, dry bottoms.

COOKTOP WARRANTY

Your cooktop is protected by this warranty

FULLONE-YEAR

WARRANTY

LIMITED 2ND-5T"

YEAR WARRANTY

(Glass Smoothtop,

Seal & Elements)

LIMITED

WARRANTY

(Applicable to the

State of Alaska)

WARRAI_.q'Y

PERIOD

One year from original

purchase date

Second through fifth

years from original

purchase date

THE CONSUMER WILL BE RESPONSIBLEFOR:

Costs of service calls that are listed under NORMAL

RESPONSIBILITIESOF THE CONSUMER. *

Diagnostic and any transportation and labor costswhich are

required because of service.

THROUGH OUR AUTHORIZED SERVICERS,

WE WILL:

Pay all costs for repairing or replacing any parts of this

appliance which prove to be defective in materials or

workmanship.

Provide a replacement for any defective surface heating

element, deteriorated rubberized-silicone seal (upswept

models only), or glasssmoothtop that cracks due to

thermal breakage (not customer abuse).

All of the provisions of the full and limited warranties

above and the exclusions listed below apply.

Time periods listed Costs of the technician's travel to the home and any costs for pick

above, up and delivery of the appliance required because of service.

In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries, Inc. We authorize no

person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by

us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by Electrolux Canada Corp.

*NORMAL

RESPONSIBILITIES

OF THE CONSUMER

EXCLUSIONS

IF YOU NEED

SERVICE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the

items listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in

accordance with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose

connections or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc.,

which are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTYDAMAGE AND INCIDENTAL EXPENSES

RESULTINGFROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation

or exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary

household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its

authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons other

than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the

warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service

under this warranty must be obtained by contacting Electrolux Home Products:

USA

1,800,944,9044

Electrolux Home Products

North America

RO. Box 212378

Augusta, GA 30917

Canada

1,866,294,9911

Electrolux Home Products

North America

802, boul. L'Ange-Gardien

L'Assomption, Quebec

J5W IT6

This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and

Canada. Product features or specifications as described or illustrated

are subject to change without notice. All warranties are made by

Electrolux Home Products North America, a division of White Consolidated

Industries, Inc. In Canada, your appliance is warranted by Electrolux

Canada Corp.

Consultez notre site web Frigidaire _:

http://www.frigidaire.com

CONTENU Page

Enregistrementde I'appareil............................................. 2

Mesuresde s6curit6 importantes.................................. 3-4

Instructionsdemise _.laterre .......................................... 4

Conversionau gazpropane.............................................. 5

Dimensionde la flamme ................................................... 5

Bon r6glagedes brOleurs................................................. 5

R6glagedescommandes des brOleursde surface

ModUlesavec brOleursouverts ................................... 6

ModUlesavec brOleursscell6s .................................... 6

ModUlesavecallumeur 61ectrique............................... 7

Choixdes ustensiles de cuisine

pour lacuisson sur les brOleurs....................................... 7

Casseroleset sous-plats particuliers................................ 8

Conseilset renseignements

sur la mise en conserve.................................................... 8

Nettoyageg6n6ral

Nettoyagedes diverses parties

de votre table de cuisson............................................ 9

ModUlesavec brOleursouverts ................................. 10

ModUlesavec brOleursscell6s .............................11-14

Liste des v6rifications pr6ventives................................. 15

Garantie..........................................................................16

LISEZ ET CONSERVEZ CES INSTRUCTIONS 318200657 (0111) Rev. C

Enregistrement de

I'appareil

Enregistrez votre appareil

LaCARTED'ENREGISTREMENT doit

_tre remplie avec soin, puis sign_e et

retourn_e _ la compagnie Produits

Electrolux Nord-Am_ricains.

Nous vous remercions d'avoir choisi cet appareil. Lesinformations contenues

dans ceguide de I'utilisateur vous indiqueront comment utiliser correctement votre

appareil etcomment en prendre soin. Veuillez lifetousles renseignements conten us

dans votre documentation pour mieux conna?tre votre nouvel appareil.

Enregistrez les num_ros de module et de s_rie de votre appareil

t_crivezci-dessous ces num_ros que vous trouverez sous la table de cuisson ou

I'int_rieur de celle-ci.

Numdro de module:

Num_ro de s_rie:

Date de I'achat:

Ce guide contient des instructions g_n_rales pour votre table de cuisson et des

renseignements s'appliquant _ plusieurs modules. Votre table de cuisson peut ne

pas avoir toutes lescaract_ristiques d_crites.

Note: Lesinstructions donn_es dans ceguide ne couvrent pastoutes lesconditions

et situations possibles. Usez de bon sens et de prudence Iors de I'installation, de

I'emploi et de I'entretien de tout appareil m_nager.

Tous droits r_serv_s

r 7T:VA:l;i/_.-,_-,]:l_vJ:l_/llSi I'information contenue dans ce guide n'est

pasexactement suivie, ilpourrait en rdsulter un feu ou une explosion

entrainant des dommages matdriels, blessures ou m_me la mort.

POUR VOTRE SI:CURITle:

n'entreposez pas ou n'utilisez pas de I'essence ou tout autre

vapeur ou liquide inflammable au voisinage de cet appareil ou de

tout autre appareil mdnager.

m QUE FAIRE SI VOUS DleTECTEZ UNE ODEUR DE GAZ:

• Ne mettez pas d'appareil en marche.

• Ne touchez pas & un commutateur dlectrique; ne vous servez

pas du tdldphone dans le b&timent.

• Allez chez le voisin et appelez immddiatement le fournisseur

de gaz. Suivez ses instructions.

• S'il n'est pas possible d'appeler le fournisseur de gaz, appelez

les pompiers

L'installation et I'entretien doivent _tre rdalisds par un

installateur qualifid, un technicien de service apr_s-vente ou le

fournisseur de gaz.

MESURES DE SleCURITI=IMPORTANTES

Lisez ces instructions avant d'utiliser I'appareil.

Conserver ces directives pour r6f6rence future.

Ceguide contient des instructions et symboles de s_curit_ importants. Veuillez faire particuli_rement attention _ cessymboles et

suivre lesinstructions donn_es. Voici une br_ve explication de ces symboles.

r!,,_\VA_l:tllll..zi.l_l_V_l_l_/lllce symbole vous pr_vient des situations qui risquent d'entraTner de graves blessures, la mort ou des

dommages materiels.

Ce symbole vous pr_vient des situations pouvant entraTner des blessuresou dommages materiels.

• Enlevez tout le ruban et le mat6riau d'emballage avant

d'utiliser latable de cuisson. D6truisez lecartonnage et lessacs

en plastique apr_s le d6ballage de I'appareil. Ne laissezjamais

les enfants jouer avec le materiau d'emballage.

• Installation--Assurez-vous que I'appareil est correctement

install6 et mis _ la terre par un technicien qualifi6,

conform6ment _ la derni_re 6dition de la norme ANSI Z223.1

du National Fuel Gaz Code aux letats Unis, ou au Canada,

conform6ment aux normes B149.1 et B149.2 CAN/ACG et

aussi conform6ment _ la derni_re 6dition de la norme n ° 70

ANSI/NFPA du National Electrical Code aux letats Unis, ou au

Canada, _ la norme C22.1 de I'ACNOR, code canadien de

1'61ectricit6, partie 1, ainsi qu'aux codes de la r6gion. N'installez

I'appareil que selon les instructions d'installation fournies dans la

documentation.

Demandez _ votre marchand de vous recommander un technicien

qualifi6 ainsi qu'un centre de r6paration autoris6. Sachez comment

couper le gaz au compteur et couper le courant electrique de latable

de cuisson _ laboTtede fusibles ou au coupe-circuit en casd'urgence.

• Entretien par I'usager--Ne r6parez pas ou ne remplacez pas

des pi_cesde I'appareil _ moinsd'une recommandation pr6cise

dans les guides. Toutes les r6parations doivent 6tre faites par un

technicien qualifi6, afin de r6duire les risques de blessure et de

dommage _ I'appareil.

• Ne modifiez jamais I'appareil, que ce soit en enlevant des

panneaux, prot_ge-fils, ou toute autre piece.

r!,'-\'A_-'i/_-_,',l_,'m II peut 6tre dangereux pour les

personnes ou dommageable pour latable de cuisson de monter

ou de s'appuyer dessus. Ne laissez pas les enfants grimper sur

I'appareil ou jouer autour.

• Rangement sur I'appareiI--Ne rangez pas sur la table de

cuisson ou pros des br_leurs de surface, des mat6riaux

inflammables. Ceci inclus des papiers, plastiques, tissus, livres de

cuisine, objets en plastique et torchons, ainsi que des liquides

inflammables. N'y posez pas des produits explosifs comme bombes

aerosol. Les produits inflammables pourraient exploser et allumer

un feu ou causer des dommages materiels.

Ne rangez pas des articles pouvant int6resser

les enfants dans les armoires au-dessus de I'appareil.

• Ne laissez pas les enfants sans surveillance dans un lieu o_ un

appareil fonctionne. Ne les laissezjamais s'asseoir ou se tenir

debout sur une piece quelconque de I'appareil.

NETOUCHEZ PASAUX BROLEURSDE SURFACE,AUX GRILLES

OU AUX ZONES A PROXIMITle DE CEUX-CI. Les br01eurs de

surface peuvent 6tre suffisamment chauds m6me silesflammes ne

sont pas visibles. Les zones pros des br01eurs peuvent devenir

suffisamment chaudes pour causer des br01ures. Pendant et apr_s

toute utilisation, netouchez paset ne laissezpasvosv6tements ou

autres produits inflammables venir en contact avec ces zones

moins qu'elles aient eu le temps de se refroidir. Ces zones

comprennent lasurface decuisson et lessurface orientees vers elle.

Portez des v_tements appropri6s--Ne portez jamais de

v_tement amples ou flottants en utilisant cet appareil. Ne

laissez pas les materiaux inflammables et les v6tements venir en

contact avec les surfaces chaudes.

llr.w_.\,A_;i/_-_._,,,l_,,/aN'utilisez jamais votre appareil pour

r6chauffer ou chauffer une piece.

N'6teignez pas les feux de friture avec de I'eau ou de la

farine--letouffez les feux avec un couvercle ou du

bicarbonate de soude, ou avec un extincteur _ poudre s_che

ou _ mousse.

• En chauffant de I'huile ou de la graisse, restez pros de

I'appareil. La graisse ou I'huile peuvent prendre feu si elles

devenaient trop chaudes.

N'utilisez que des gants isolants secs--Des gants isolants

mouill6s ou humides en contact avec des surfaces chaudes

peuvent causer des br_lures par la vapeur. Ne laissez pas les

gants isolantstoucher les br01eurs ou la flamme. Ne vous servez pas

de torchon ni de chiffon _ la place d'un gant isolant.

Ne r6chauffez pas des contenants non ouverts--

L'accumulation de pression peut faire exploser le contenant

et blesser.

Vous devez savoir quel bouton commande chacun des

br_leurs de surface. Tournez le bouton _ la position "LITE"

(ALLUMAGE) pour mettre les brOleurs en marche. V6rifiez que le

brOleur est allum6 puis r6glez la flamme pour qu'elle ne depasse

pas de I'ustensile.

rrv_.\,i_;i/._q_,,_l_/n Bonne dimension de la flamme--

R6glez la flamme pour qu'elle ne d6passe pas du bord de

I'ustensile. Avec des ustensiles de dimension insuffisante, une partie

de laflamme du br01eurseraexpos6e et risquera de mettre lafeu aux

v6tements. Un bon contact entre I'ustensile et la flamme am61iore

aussi I'efficacite.

r! T_,\vl_-'il/ i-'__]=1_I=1_IIIII N'utilisez pas des grilles de r6chaud sur

vos br_leurs _ gaz scell6s. Sinon, la combustion serait incomplete

et il pourrait en r6sulter un degagement de monoxyde de carbone

des doses sup6rieures aux niveaux admis, ce qui serait dangereux

pour votre sante.

MESURES DE SI CURITI IMPORTANTEScsuite

• Utilisez la grosseur de casserole appropri_e--Cet appareil est

equip_ d'un ou plusieurs brOleurs de surface de differentes

grosseurs. Choisissiez les ustensiles ayant un dessous plat, assez

large pour recouvrir le brOleur. Sivous utilisez des ustensiles trop

petits, une partie du brOleur sera _ decouvert, et les v_tements

entrant directement en contact avec le brOleur sont susceptibles de

prendre feu. L'utilisation d'ustensiles d'une taille proportionnelle

au brOleur am_liore aussi le rendement.

• Les poigndes d'ustensiles doivent _tre tourndes vers

I'intdrieur, sans surplomber les brQleurs adjacents, afin de

r_duire les risques de brOlure, de combustion et de renversements

causes par le contact involontaire avec un ustensile.

• Ne laissez jamais les br_leurs de surface sans surveillance _ des

r_glages _lev_s--Les debordements causent de la fum_e, les

eclaboussures de graisse sont susceptibles de prendre feu et les

ustensiles dont le contenu s'est evapor_ peuvent fondre.

• Protecteurs--N'utilisez pas de papier d'aluminium pour recouvrir

les cuvettes des brOleurs de surface ou toute autre partie de

I'appareil. Utilisez seulement le papier d'aluminium pour recouvrir

la nourriture durant la cuisson au four. Toute autre utilisation de

protecteurs ou de papier aluminium est susceptible de causer un

choc electrique, un feu ou un court-circuit.

• Ustensile vitrifi_s--En raison de brusques changements de

temperature, on ne peut utiliser avec la surface de cuisson que

certains ustensiles en verre, en vitroc_ramique ou en terre cuite, ou

autres ustensiles vitrifies, sans risquer qu'ils sefendent. V_rifiez les

recommandations du fabricant quant ) leur utilisation sur une

surface de cuisson.

N'utilisez pasdecouverclede br_leurd_coratif. Siun br01eurest

accidentellement allum_, le couvercle risque de chauffer et

eventuellement de fondre. Vous risquez devous brOler en touchant

lecouvercle. Aussi, ily a risque d'endommagement de la surface de

cuisson et des brOleurss'ily a surchauffe du couvercle. L'air seraaussi

bloque, ce qui entrafnera des probl_mes de combustion.

SURFACE EN VERRE (certainsmodules):

• Ne nettoyez pas et ne faites pas fonctionner une table de

cuisson avec une vitre cass_e--Si le verre de la surface est fissure,

lessolutions de nettoyage et produits renvers_s pourraient p_netrer

I'interieur de la surface de cuisson et entrafner un risque de

decharge electrique. Prenez contact imm_diatement avec un

technicien qualifi&

Nettoyez prudemment le verre de la surface de cuisson--Si

vous utilisez un linge ou une Sponge humide pour enlever les

produits renvers_s sur une surface de cuisson chaude, faites

attention _ ne pas vous brOler par la vapeur. Certains produits de

nettoyage peuvent degager des vapeurs dangereuses s'ils sont

appliques sur une surface chaude.

Ne placez pas d'ustensiles de cuisine chauds sur le verre de la

table de cuisson. Ceci pourrait le casser.

I_viter de gratter le verre de la table de cuisson avec des objets

pointus.

AVIS DE SECURITE IMPORTANT

Le decret Californien de r_gulation des dechets toxiques et de la qualite de I'eau potable demande au Gouvernement de la Californie

de rendre publique I'enum_ration des substances causant le cancer, les malformations congenitales ou autres dommages de

reproduction connues _ I'etat, et exige que les entreprises avertissent leurs clients des risques potentiels d'exposition _ ces substances.

CONSERVEZ CES INSTRUCTIONS

Instructions de mise la terre

(modUles E allumage _lectrique seulement)

IMPORTANT: LIREET CONSERVER CES INSTRUCTIONS.

lll'!If__\vA:lltl/I-'_-l:l_V_l:l_/llCet appareil est _quip_ d'une fiche _ trois broches avec

mise _ la terre pour assurer votre protection contre leschocs _lectriques. Cette

fiche doit _tre branch_e directement dans une prise correctement mise _ laterre.

Ne coupez PAS, n'enlevez pas la broche de mise _ la terre de cette fiche.

Pour des raisons de s_curit_ personnelle, cette table de cuisson doit _tre

correctement mise _ la terre. La fiche doit _tre branch_e dans un prise

correctement polaris_e et mise _ la terre, de 120 volts, 60 hertz.

Si une prise murale _ deux alv_oles est la seule prise _ votre disposition, il vous

revient de demander _ un _lectricien qualifi_ de laremplacer par une prisemurale

trois alv_oles correctement mise _ la terre.

EN AUCUN CAS, IL NE FAUT COUPER OU ENLEVER LA BROCHE DE MISE A LA

TERRE DE CETTE FICHE. CONSULTEZ LES INSTRUCTIONS D'INSTALLATION

EMBALLI_ES AVEC CETAPPAREIL POUR YTROUVER TOUS LESRENSEIGNEMENTS

SUR L'INSTALLATION ET LA MISE A LA TERRE. VOUS NE DEVEZ JAMAIS VOUS

SERVlR DE L'APPAREIL AVEC UN CORDON PROLONGATEUR OU D'UNE FICHE

D'ADAPTATION A DEUX BROCHES.

llf!_E_\_i=l;i/t-_'t=l,N=l_|/IEvitertout risque

de feu ou de choc_lectrique. Nepasutiliser

de cordon prolongateur ni de fiche

d'adaptation. Ne pas enlever la broche de

raise_ la terre du cordon _lectrique. Si cet

avertissementn'_tait passuivi,il pourrait en

r_sulter de graves blessures,la mort ou un

incendie.

Prise murale

mise _ la

terre

jamais couper,

Cordon

d'alimentation

muni d'une fiche

trois broches

avec mise _ la

terre.

La page charge ...

Frigidaire FGC30S4AQB Le manuel du propriétaire

Marque: Frigidaire

Modèle: FGC30S4AQB

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Frigidaire FGC30S4AQB Owner's manual

Frigidaire FGC30S4AQB Le manuel du propriétaire

Ce manuel convient également à

Frigidaire FGC30S4AQB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents