MyBinding GBC Falcon 3064-1 Manuel utilisateur

GBC Falcon 3064-1

Wide Format Laminator

- 1712489

Instruction Manual

GBC 3064WF Operation Manual

GBC 3064WF

INSTALLATION & OPERATING MANUAL

Part Number: 930-131, Rev A.

ENG Operating Instructions

F Mode d'Emploi

E Instrucciones de Operación

Part Number: 930-131.REV.10-17-05

GBC 3064WF Operation Manual

ENG

The information in this publication is provided for reference and is believed to be accurate and complete. General Binding Corporation (GBC) is not liable for errors in

this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not limited to,

any implied warranty of fitness or merchantability for any particular use.

GBC reserves the right to make changes to this publication and to the products described in it without notice. All specifications and information concerning products

are subject to change without notice. Reference in this publication to information or products protected by copyright or patent does not convey any license under the

rights of GBC or others. GBC assumes no liability arising from infringements of patents or any other rights of third parties.

transmitted, or transferred, in whole or in part, in any form without the prior and express written permission of GBC.

F

L’information contenue dans cette publication est fournie à titre de référence et elle est considérée exacte et complète. General Binding Corporation (GBC) n’est pas

responsable des erreurs contenues dans cette publication ni des dommages indirects ou consécutifs portant sur l’utilisation ou la présentation de l’information de ce

document, y compris, mais sans s’y limiter, toute garantie implicite de commercialité ou d’adaptation à un usage particulier.

GBC se réserve le droit d’apporter des modifications à cette publication et aux produits qui y sont décrits sans préavis. Toutes les spécifications et l’information au sujet

des produits sont sujettes à changements sans préavis.

Toute référence à l’information ou aux produits protégés par un droit d’auteur ou un brevet présentée dans ce document ne porte aucune licence sous les droits de GBC

ou d’autres parties. GBC n’assume aucune responsabilité découlant de contraventions aux brevets ou à tout autre droit de tierces parties.

reproduite, mise en mémoire, transmise ou transférée, en partie ou en entier, sous quelque forme que ce soit sans la permission écrite préalable et expresse de GBC.

E

La información contenida en esta publicación es proporcionada a título de referencia y se considera que es precisa y completa. General Binding Corporation (GBC) no

es responsable por errores contenidos en esta publicación o por daños consecuentes o incidentales relacionados con la disponibilidad o el uso de la información en esta

publicación, incluyendo y sin limitarse a, cualquier garantía de aptitud y comerciabilidad para cualquier uso específico.

GBC se reserva el derecho de hacer cambios en esta publicación y a los productos descritos en la misma sin aviso previo. Todas las características y la información

referente a los productos, están sujetas a cambios sin aviso previo.

Las referencias en esta publicación a información o productos protegidos por derechos de propiedad intelectual o por patentes no otorga ninguna licencia amparada por

los derechos de GBC u otros. GBC no asume ninguna responsabilidad que se derive de la violación de patentes u otros derechos de terceras partes.

documento es de propiedad exclusiva y no puede reproducirse, almacenarse, transmitirse o transferirse, en su totalidad o en partes, y de ninguna manera, sin la

autorización previa y por escrito de GBC.

GBC 3064WF Operation Manual

ENG

TABLE OF CONTENTS

Description

Page

No.

Description

Page

No.

Cover

Legal Disclaimer

Table of Contents

Important Safety Instructions

Important Safeguards

General

Electrical

Service

Warranty

Specifications

Pre- Installation

Installation

Control Guide

Power ON/OFF

Control Panel

LCD Display

Display Reset Switch

Display

Main Switch (TOP Heater)

Display

Main Switch (Bottom Heater)

Fan Switch

Main Roller (Up / Down)

Pull Roller (Up / Down)

Laminator main Control Switch

Machine Power On Light

Laminator Directional Motion

Control Switch

Laminator Speed Control

Features Guide

Emergency-Stop Buttons

Media Tray Table

Rewind Take up

Swing out Film Unwind Shaft

Unwind / Rewind Combo

Rewind Take Up

Removable Chill Idler

Upper Tension Idler

Lower Tension Idler

Pull Rollers

Heated Main Rollers

Table Idler

Main On / Off Switch

Swing around Control

Panel Arm

Control Panel Box

Electric Safety Beam

Nip Pressure Adjustment

Pull roll Lift handle

Main Roller Lift Handle

Pull Role Clutch Adjustment Knob

1

2

3

4

5

6

7

8

9

10

11

12

13

Sequence of Operations

Operating Instructions

Film Loading and Threading

Load a Roll of Film

Webbing Thermal Film using

Threading Card

Webbing PSA Film / Mount Adhesive

Using Threading Card

Start Laminating

Method for Tacking new Film to

Existing Film

To Unweb The Laminator

Clearing a Film Jam (Wrap– Up)

Applications

Tips for Pre-Coating Boards

Tips for Mounting Pre-Coated Boards

Tips for Single Sided Lamination

Tips for Creating a Decal

Tips for Mounting a Decal

Thermal Encapsulation

AccuShield™

Speed/Temperature Control

The Art of Lamination

Basic Rules

Film Tension

Heat

Output

Maintenance

Trouble Shooting Guide

Service Agreement

14

15

16

17

18

19

20

21

22

23

24

25

26

27

GBC 3064WF Operation Manual

IMPORTANT SAFETY INSTRUCTIONS

YOUR SAFETY AS WELL AS THE SAFETY OF

OTHERS IS IMPORTANT TO GBC. IN THIS

INSTRUCTION MANUAL AND ON THE PRODUCT,

YOU WILL FIND IMPORTANT SAFETY MESSAGES

REGARDING THE PRODUCT. READ THESE

MESSAGES CAREFULLY. READ ALL OF THE

INSTRUCTIONS AND SAVE THESE

INSTRUCTIONS FOR LATER USE.

THE SAFETY ALERT SYMBOL PRECEDES

EACH SAFETY MESSAGE IN THIS

INSTRUCTION MANUAL. THE SYMBOL

INDICATES A POTENTIAL PERSONAL

SAFETY HAZARD TO YOU OR OTHERS.

THE FOLLOWING WARNINGS ARE

FOUND UPON THIS PRODUCT.

ADVERTENCIA

Attention

Avertissement

Riesgo de choque

eléctrico

No abra:

Adentro no hay

piezas reparables

por el usuario.

Mantenimiento

solamente por

personal calificado

Risque de

Secousseélectrique.

Ne pas ouvrir.

Pas de pièces

réparables par

l'utilisateur.

Entretien

seulement par

personnel qualifié.

Electrical shock

hazard.

Do not open.

No user serviceable

parts inside.

Refer servicing to

qualified service

personnel.

THIS SAFETY MESSAGE MEANS THAT YOU

COULD BE SERIOUSLY HURT OR KILLED IF YOU

OPEN THE PRODUCT AND EXPOSE YOURSELF

TO HAZARDOUS VOLTAGE.

THIS SAFETY MESSAGE MEANS THAT YOU

COULD BE BURNED AND YOUR FINGERS COULD

BE TRAPPED AND CRUSHED IN THE HOT

ROLLERS. CLOTHING, JEWELRY AND LONG

HAIR COULD BE CAUGHT IN THE ROLLERS AND

PULL YOU INTO THEM.

ADVERTENCIA

Attention

Avertissement

NAVAJA FILOSA.

Mantener manos y

dedos a distancia.

LAME

COUPANTE.

Tenir mains et

doigts à l'écart.

SHARP BLADE.

Keep hands and

clothing away.

THIS SAFETY MESSAGE MEANS THAT YOU

COULD CUT YOURSELF IF YOU ARE NOT

CAREFUL.

WARNING: THIS SAFETY ALERT

SYMBOL PRECEDES EACH SAFETY

MESSAGE IN THIS INSTRUCTION

MANUAL. THE SYMBOL INDICATES A

POTENTAL PERSONAL SAFETY HAZARD

TO YOU OR OTHERS.

WARNING: DO NOT ATTEMPT TO

SERVICE OR REPAIR THE 3064 WF

LAMINATOR.

WARNING: DO NOT CONNECT THE

LAMINATOR TO AN ELECTRICAL

SUPPLY OR ATTEMPT TO OPERATE THE

LAMINATOR UNTIL YOU HAVE

COMPLETELY READ THESE

INSTRUCTIONS. MAINTAIN THESE

INSTRUCTIONS IN A CONVENIENT

LOCATION FOR FUTURE REFERENCE.

IMPORTANT SAFEGUARDS

WARNING: TO GUARD AGAINST INJURY

THE FOLLOWING SAFETY

PRECAUTIONS MUST BE OBSERVED IN

INSTALLATION AND USE OF THE

LAMINATOR.

General:

Keep hands, long hair, loose clothing, and articles such as

necklaces or ties away from the front of the heat and pull

rollers to avoid entanglement and entrapment.

The heat rollers can reach temperatures over 300

o

F (150

o

C).

Avoid contact with the heat rollers during operation or shortly

after power has been removed from the laminator.

Keep hands and fingers away from the path of the sharp film

cutter blade located at the film exit.

Do not use the laminator for other than its intended purpose.

Avoid moving the Laminator on uneven floor surfaces. Never

tilt the laminator.

Do not defeat or remove electrical and mechanical safety

equipment such as interlocks, shields and guards.

Do not insert objects unsuitable for laminating or expose the

equipment to liquids.

Electrical:

The Laminator should be connected only to a source of power

as indicated in these instructions and on the serial plate located

on the rear of the laminator. Contact an electrician should the

attachment plug provided with the Laminator not match the

receptacles at your location.

WARNING: THE RECEPTACLE MUST BE

LOCATED NEAR THE EQUIPMENT AND

EASILY ACCESSIBLE.

Do not operate the Laminator with a damaged power supply

cord or attachment plug, upon occurrence of a malfunction, or

after the laminator has been damaged. Contact GBC’s

Technical Service Department or your dealer/distributor for

assistance.

Service:

Perform only the routine maintenance procedures referred to in

these instructions

WARNING: DO NOT ATTEMPT TO SERVICE

OR REPAIR THE LAMINATOR

Disconnect the plug from the receptacle and contact GBC’s

Technical Department or your dealer/distributor when one or

more of the following has occurred.

• The power supply cord or attachment plug is damaged.

• Liquid has been spilled into the laminator.

• The laminator is malfunctioning after being mishandled.

• The laminator does not operate as described in these

instructions.

ADVERTENCIA

Attention

Avertissement

RODILLOS

CALIENTES.

PUNTO DE

PINCHAMIENTO.

Mantener manos y

ropa a distancia.

ROULEAUX

CHAUDS.

POINT DE

PINCEMENT.

Tenir mains et

vêtements à

l'écart.

HOT ROLLS.

PINCH POINT.

Keep hands and

clothing away.

GBC 3064WF Operation Manual

WARRANTY

Limited 90- Day Warranty

GBC warrants to the original purchaser for a period of ninety

days on labor and one year on parts after installation that this

laminator is free from defects in workmanship and material

under normal use and service. GBC’s obligation under this

limited warranty is limited to replacement or repair, at GBC’s

option, of any part found defective by GBC without charge for

material or labor.

THIS LIMITED WARRANTY IS IN LIEU OF ALL

OTHER WARRANTIES EXPRESSED OR IMPLIED.

WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE ARE EXPRESSLY

EXCLUDED. ANY REPRESENTATIONS OR PROMISES

INCONSISTENT WITH, OR IN ADDITION TO, THIS

LIMITED WARRANTY ARE UNAUTHORIZED AND

SHALL NOT BE BINDING UPON GBC. IN NO EVENT

SHALL GBC BE LIABLE FOR ANY SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

WHETHER OR NOT FORESEEABLE.

This limited warranty shall be void if the laminator has been

misused; mishandled; damaged by negligence, by accident,

during shipment, or due to exposure to extreme conditions;

repaired, altered, moved, or installed by anyone other than GBC

or its authorized agents; or if incompatible film was used.

GBC’s obligation under this limited warranty does not include

routine maintenance, cleaning, adjustment, normal cosmetic or

mechanical wear, or freight charges.

Without limiting the generality of the previous paragraph,

GBC’s obligation under this limited warranty does not include:

1. Damage caused to the rollers by knives, razors, or other

sharp tools: by any foreign objects falling into the working

area of the laminator; or by cleaning the laminator with

solutions or materials that harm its surfaces;

2. Damage caused by adhesives; nor

3. Damage caused by lifting, tilting or attempting to position

the laminator other than rolling it on its castors across even

surfaces.

FOR EUROPEAN UNION RESIDENTS ONLY: This

guarantee does not affect the legal rights which consumers have

under applicable national legislation governing the sale of

consumer goods.

SPECIFICATIONS

Operating Speed Up to 20 fpm (5.5 mpm) MAX

Maximum Temperature 300

o

F (149

o

C)

Maximum Mounting

Thickness

1 in. (25.4 mm) Max.

Maximum Film Width 64 in. (162.5 cm)

Dimensions (W x D x H) Unit alone: (Uncrated)

86in. x 34.5in. x 57in.

(218cm x 88cm x 145cm.)

Depth of 3064 WF is 44 in (112 cm) with tables in up position.

Weight

Unit alone: 1500 lbs. (680 Kgs.).

Shipping: 1700 lbs. (771 Kgs.).

Electrical Requirements Refer to the serial plate located on the rear of the laminator for the specific electrical rating applicable

to the unit.

Agency Approval cULus

Voltage 220 V, 60 Hz

Current 32 A

Power 7000 W

Phase Single

FCC NOTE

FCC Class A Notice - Notification pour les Etats-Unis

Note: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiated radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Canada Class A Notice - Avis Canada, Classe A

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Modifications

Any modifications made to this device that are not approved by General Binding Corporation may

void the authority granted to the user by the FCC and/or by Industry Canada to operate this

equipment.

Toutes modifications apportées à ce dispositif et non approuvées par General Binding Corporation

annuleront le droit accordé à l'utilisateur par le FCC et/ou par Industrie Canada de faire fonctionner

cet équipement.

GBC 3064WF Operation Manual

PRE-INSTALLATION

Before a 3064 Laminator can be installed, ensure the

following requirements are met:

1. Are doorways and hallways wide enough for the

laminator to be moved to the installation site?

2. Is there ample room for the laminator?

• A work area must be established that allows for

operation in both the front and rear of the

laminator and provides space for efficient

material flow.

3. Is the environment appropriate for the laminator?

• The laminator requires a clean, dust and vapor

free environment to operate properly.

• Avoid locating the laminator near sources of heat

or cold. Avoid locating the laminator in the direct

path of forced, heated or cooled air.

CAUTION: Air flow can cause uneven heating /

cooling of the rollers and result in poor output

quality.

4. Have you contacted a certified electrician to wire the

receptacle and ensure that adequate power is being

supplied, having the appropriate capacity, over

current protection and safety lockouts available?

GBC 3064 WF Requires:

• 220V at 60Hz with 32 amps single phase.

• Nema 6-50 R 50 A 250 V Receptacle

This Machine is supplied with a Nema 6-50 male

Plug

INSTALLATION

1. Shipping damage should be brought to the immediate attention of the delivering carrier.

2. With assistance, carefully roll the laminator into position over flat and even surfaces.

3. The laminator should be positioned to allow exiting film to flow freely to the floor or a work table. Accumulation of

laminate immediately behind the laminator as it exits the equipment may cause the film to wrap around the pull rollers,

resulting in a “jammed” condition.

4. Avoid locating the laminator near sources of heat or cold. Avoid locating the laminator in the direct path of forced,

heated or cooled air.

5. Once the laminator has been properly positioned, lock the castors in place. Locking the castors prevent the machine

from rolling during set up, operation or servicing.

6. Connect the attachment plug provided with the laminator to a suitably grounded outlet. Avoid connecting other

equipment to the same branch circuit to which the laminator is connected, as this may result in nuisance tripping of

circuit breakers or blowing fuses.

Note: Machine must be leveled to ensure best performance. Level the machine by lowering both the main and pull rolls.

Lay A level on top of the main and pull rolls. Then, check level from main roll to pull roll on right and left side of the

roll. Finally, check by placing the level diagonally across lower main to lower pull rolls.

GBC 3064WF Operation Manual

CONTROL GUIDE

A. Power ON/OFF (I/O):

Located at the back left of the machine applies power to the

laminator. The control panel display will illuminate when

position marked “I” is pushed. The Off position, marked “O”

removes power from the laminator.

B. Control Panel (Figure 5)

1. Main Roll Nip Pressure relevant pressure in percentage:

2. Top Roll Display

• Displays Temperature in “

o

C “or “

o

F” of the Top Heater

(Both Set Temperature and Current Temperature)

• LED Marked “

o

C” if Illuminated indicates reading in “

o

C “

• LED Marked “

o

F” if Illuminated indicates Temperature reading

in “

o

F”

• LED Marked “Ready” illuminates when set temperature is

reached.

{a}. Control Switches:

⌃

- When Pressed Increases the Temperature

- When Pressed Decreases the Temperature

MEAS- Press and Hold to Display Current Top Roller

Temperature

3. Main Switch (TOP Heater): When pressed to the

Position turns On the top heater, when pressed to the

Position turns Off the top heater.

4. Bottom Roll Display

• Displays Temperature in “

o

C” or “

o

F” of the Bottom Heater

(Both set Temperature and Current Temperature when

MEAS switch is pressed)

• LED Marked “

o

C” if Illuminated indicates reading in “

o

C”

• LED Marked “°F” if Illuminated indicates Temperature reading

in “

o

F”

• LED Marked “Ready” illuminates when set temperature is

reached.

MEAS- Press and Hold to Display Current Bottom Roller

Temperature

{b}. Control Switches

∧ - When Pressed Increases the Temperature

∨ - When Pressed Decreases the Temperature

MEAS-Press and Hold to Display Current Bottom Roller

Temperature

5. Main Switch (Bottom Heater): When pressed to the

position turns On the bottom heater, when pressed to the

position turns Off the bottom heater.

6. Fan Switch: Switches cooling fan ON / OFF

7. Laminator Main Control Switch: Switches the

laminator between “RUN” and “STOP” modes.

8. Machine Power On Light: Green light illuminated –

Machine On.

9. Laminator Direction Motion Control Switch: Controls the

forward and rearward movement of the laminator.

10. Laminator Speed Control:

Regulates the speed of laminator feed.

• Outer Scale in Feet/Minute.

1

2

3

a

4

b

5

6

1

7

9

8

Figure 5

GBC 3064WF Operation Manual

FEATURES GUIDE

Refer to the following pages for detailed information on the above Features

FEATURES GUIDE (DETAILED DESCRIPTION)

A

Figure 1

EMERGENCY STOP BUTTONS

(Fig. 1– Item A)

Four emergency stop buttons are available on

the Laminator on the top four corners of the

Laminator.

To engage Emergency -stop button, Press any

emergency -stop safety push button to stop

the roller movement

To disengage, turn the push button clockwise

after the emergency condition has been

resolved.

GBC 3064WF Operation Manual

Media Tables: (Fig. 2C & 3C)

On both the Front Media & Rear Media tables,

the safety interlock switch will not allow the

Laminator to operate at full speed unless the

tables are properly installed.

The Media tables are used to position items for

Lamination. There are two media tables on the

machine one on the front & one on the rear of

the Laminator. The Front Media table

incorporates an Idler on the leading edge of the

table. This is used for roll to roll applications

during lamination

Note:

The Laminator will operate only when the

Media Table and Media Table Latch are

Properly Installed.

The Accessories Include:

1. Straight Slitter: Used for slitting the

media after lamination -- Rear Table.

(Fig. 3 – Item B)

2. Feed Guide: Used for guiding Media

through the laminator (Fig. 2B)

3. Pressure Plate: Used for guiding stock

and ensuring a wrinkle free feed into the

roller Nip. (Fig 2A)

Rewind Take up: (Fig. 3 – Item A)

This machine has one dedicated rewind film

take up positioned on the lower back of the

machine

Swing out Film Unwind Shaft: (Fig. 4C)

Swing out film unwind shaft is used to provide

tension to materials going into the lamination

roles. The unwind is located on the lower front

of laminator. (Fig. 4 – Item C)

The swing out unwind shaft brake knob varies

the tension. (Fig. 4E)

Unwind / Rewind Combo: (Fig. 4 & 5)

There are three unwind/rewind combo shafts,

Two Top Combo Unwind/Rewind shafts, one

on the top front and one on the top back of the

machine (Fig. 5A) and the third combo

unwind/rewind shaft is located below the front

table (Fig. 4B).

Unwind / rewind combo shafts can be used as a

standard swing out unwind for material supply

or be used as a rewind for liners and final

products.

The conversion from unwind to rewind just

requires the release of the upper brake adjust

knob (Fig. 4D) and tightening the rewind

adjustment knob. (Fig. 4F)

CAUTION: When using the combo unwind /

rewind shaft as a rewind, the upper brake

adjust knob (Fig. 4D) must be released to

limit the load on the motor, and wear & tear

on the machine.

The film shaft clutch is then engaged to the turn

with the motor to wind up film.

A

B

C

A

C

B

C

F

Figure 2

Figure 3

D

E

Figure 4

GBC 3064WF Operation Manual

Removable Chill Idler: (Fig. 6 – Item A)

The removable chill Idler is used to help smooth out

the laminating film during the cooling process.

Figure 6

A

Figure 5

GBC 3064WF Operation Manual

Figure 7

A

Figure 9

A

Figure 8

Upper Tension Idler: (Fig. 7 – Item A)

Upper tension Idler guides the laminating film

on to the main roll insuring a consistent amount

of wrap on the upper rolls.

Lower Tension Idler: (Fig. 8 - Item B)

Lower tension idler guides the lower lamination

film on to the lower roller.

Pull Rollers: (Fig. 9 - Item A)

The Pull rollers located at the back of the

laminator are motor driven. They

simultaneously pull the film and improve the

quality of the laminated item.

B

GBC 3064WF Operation Manual

Figure 11

Figure 12

A

B

A

Heated Main Rollers: (Fig. 10 – Item A)

Silicone rubber coated steel tubes heat the

laminating film and compresses the heated film

to the items being laminated. Heat is provided

by an internal heating element.

Table Idler: (Fig. 10 – Item B)

The Table Idler is used to assist in bringing the

material up to the nip.

The table Idler is helpful in roll to roll operation

and helps move large ridged panels through the

nip.

Main On / Off (I/O) Switch:

(Fig. 11 – Item A)

Located on the lower back of the control panel

side of the GBC3064WF is the main power

switch.

“I” means ON, ”O” means OFF.

Swing around control panel arm:

(Fig. 12 – Item A)

The Control panel is on a swing around arm

which will allow the operator to move the

necessary control to each side of the machine.

Control Panel: (Fig. 12 – Item B)

The Control panel has most of the machine

controls to operate the machine.

Electronic Safety Beam: (Fig. 13 – Item A)

Safety light beam is used to protect the Nip area

with out being, in the way of normal lamination

operation. Please see the following chart for

sequence of operations on Page 14.

Figure 13

A

Figure 10

B

GBC 3064WF Operation Manual

Figure 14

A

Nip Pressure Adjustment:

(Fig. 14 & 15 –Item A)

The Nip pressure adjustment allows the operator

to adjust the downward pressure of the pull rolls

and main rolls.

Pull Roll Lift handle:

Turn the handle clockwise to lower the upper

pull roll. (Fig. 14A)

Heated Main roll Lift handle:

Turn handle clockwise to lower main roll &

adjust the Nip Pressure (Fig. 15A)

Pull Roll Clutch Adjustment Knob:

The Pull Roll Clutch provides tension on the

laminated film between the main rolls and pull

rolls as the material is cooling. (Fig. 16A)

A

Figure 15

Figure 16

A

GBC 3064WF Operation Manual

SEQUENCE OF OPERATIONS

GBC U.S &CE 3064WF

Effect of Fiber Optics on sequence of operation

Modes Situation 1 Situation 2 Situation 3

Machine Run Mode

Normal operation

(No Interruption to any

safety circuitry & Fiber

optic beam)High speed.

Interrupted fiber optic

beam or opened any

safety circuitry.

Fiber optic beam cleared + all safety

circuitries are closed

Control panel:

Forward Speed: Zero to

Max.

Press “RUN” push

button to switch over

from foot switch to the

control panel.

Machine stops Instantly.

Use foot pedal to override

@ 3f/m.

Machine will remain stationary until

run switch is pressed.

Push RUN button switch to run

machine again (Normal operation)

mode.

Forward Mode

Press push button

forward switch

Foot switch:

Forward Speed: Zero to

Max.

Note: Press variable

foot pedal to change

mode and take over

from control panel at

preset speed.

Machine Runs @

3f/m.

(Automatic override from

high to low voltage)

Machine still remains at low voltage

speed of 3f/m.

Steps required to run at (various

speed): The operator will have two

choices,

Choice A:

1. Release foot pedal to stop machine.

2. Press foot pedal again to start

machine at original preset control

panel knob speed (pot).

Choice B:

1. Press and hold “RUN” push button

switch on the control panel while foot

is still on pedal.

2. Release foot pedal.

3. Adjust speed using “speed knob”

Reverse speed: Zero to

Max.

Press “Run” push

button to switch over

from Foot switch to the

Control panel.

Machine stops Instantly.

Use Foot pedal to

override @ 3f/m.

Machine must not run. It will remain

stationary.

Push RUN button switch to run

machine again at Normal operation

mode.

Reverse Mode

Press Reverse

Push button switch.

Reverse speed: Zero to

Max.

Note: Press foot pedal

to change mode and

take over from control

panel.

Machine Runs @ 3f/m.

(Automatic override from

high to low voltage)

Machine still remains at low voltage

speed of 3f/m.

Steps required to run at (various

speed): The operator will have two

choices,

Choice A:

1. Release foot pedal to stop machine.

2. Press foot pedal again to start

machine at original preset control

panel knob speed (pot).

Choice B:

1. Press and hold “RUN” push button

switch on the control panel while foot

is still on pedal.

2. Release foot pedal.

3. Adjust speed using “speed knob”

GBC 3064WF Operation Manual

OPERATING INSTRUCTIONS

P

o

l

y

-

i

n

A

d

h

e

si

v

e

su

r

f

a

c

e

Polyester surface

P

o

l

y

-

o

u

t

A

d

h

e

si

v

e

su

r

f

a

c

e

Polyester surface

1

5

2

3

4

6

=

Film Loading & Threading

The top and bottom rolls of laminating film must be

of the same width and be present simultaneously. A

Small amount of adhesive will “squeeze out” during

Lamination. Hardened adhesive deposits can damage

the heat rollers.

CAUTION:

Adhesive will deposit on the rollers if:

• Only one roll is used.

• Different widths of rolls are loaded together.

• Either roll is loaded adhesive side against a heat

roller.

• One or both rolls of film are allowed to run

completely off its core.

The adhesive side of the film is on the inner side of

the web (Fig. 17A & B). The shiny side of clear film

must contact the heat rollers. The dull side of the

film contains the adhesive. Use extreme caution

when loading delustered (matte) film as both sides

appear dull.

Always change the top and bottom supply rolls at the

same time. Near the end of each roll of GBC

laminating film is a label stating “Warning-End of

Roll”. The appearance of this label on either the top

or bottom roll requires that new rolls of film be

installed as soon as the item presently being

laminated completely exits the rear of the laminator.

Do not introduce any additional items into the

laminator when the warning label is visible.

To load a roll of film: (Fig. 18)

1. Pull the swing out shaft clevis pin up.

2. Swing shaft outward.

3. Slide the roll of film onto the film shaft ensuring

Adhesive side is out.

4. Push the film shaft back into the film shaft

Support saddle.

5. Push the clevis pin down.

6. Center the roll of film.

Figure 17

Figure 18

A

B

GBC 3064WF Operation Manual

THERMAL

LAMINATE

THERMAL

LAMINATE

THERMAL

LAMINATE

Webbing Thermal Film Using Threading Card

CAUTION: The laminator rollers will be hot and

can burn you.

1. Turn the Main Power ON /OFF to On.

2. Set top and bottom temperatures to the appropriate

setting for the film type used.

3. Ensure no brake tension is applied to the film shafts.

4. Pull the top roll film down under the upper idler bar

and allow to drape over the top heat roller (Fig. 19)

5. Pull the lower film behind the lower idler bar, Lower

the table, Pull Film up towards the film draped over

the top heat roller and adhere the lower film to the

upper Film (Fig. 20).

6. Pivot the table back to its feeding position while

ensuring the threading card is on top of the feed table

(Fig. 21).

7. Use a threading card to push the two materials into

the heat roller nip.

8. Lower the main roller to initial contact with the

threading card.

9. Ensure FRONT is selected for Motor direction and

Press the Foot Switch

10. From the rear of the machine, guide the web over the

chill idler, if installed, and through the pull rollers.

11. Once the web has entered the pull roller nip, lower

the pull roller. Adjust unwind film tension; use as

little tension as possible to get smooth output.

(See Page. 9)

12. Once the threading card has completely exited the

pull rollers, press the “STOP” ( ) button.

13. Now refer to the section titled “START

LAMINATING”.

Figure 19

Figure 20

Figure 21

GBC 3064WF Operation Manual

REWIND TUBE

Adhesive

Mount

Film

PSA

REWIND TUBE

Adhesive

Mount

Film

PSA

REWIND TUBE

HEAT ROLLER

CHILLED ROLLER

Adhesive

Mount

Film

PSA

Webbing PSA Film/Mount Adhesive Using

Threading Card

The laminator should be cool to the touch before

Proceeding.

1. Turn the Power ON /OFF to On

2. Load the rolls of film as illustrated in (Fig. 22).

Ensure no brake tension is applied to the film

shafts.

3. Pull the top roll of film down under the idler bar

and up to the upper front rewind tube.

4. Place one piece of masking tape in the center of

the film and secure to the rewind tube.

5. Make two full wraps around the rewind tube,

and then score the laminate without cutting the

release liner. Pull the laminate down allowing it

to drape over the upper roller (Fig. 22).

6. Pull the mount adhesive up towards the film

draped over the upper heat roller (Fig. 23).

7. Stick the mount adhesive to the exposed

adhesive of the upper roller.

8. Pivot the table back to its feeding position while

ensuring the threading card is on top of the feed

table (Fig. 24).

9. Use a threading card to push the two materials

through the heat roller nip

10. Lower the main heated roller to bring the main

roller into initial contact with the threading card.

Ensure front is selected and press the foot

switch.

11. From the rear of the machine, guide the web

over the chill idler, if installed, and through the

pull rollers. Once the web has entered the pull

roller nip, close the pull roller nip.

12. Press the “STOP” ( ) button when the

threading card has completely exited the pull

rollers and adjusts the film web tension using as

little tension as possible.

13. Now refer to the section titled “START

LAMINATING”.

Figure 22

Figure 23

Figure 24

GBC 3064WF Operation Manual

Figure 25

Figure 26

Start Laminating

1. At this point you should have your laminator

Webbed with the appropriate material for your

application.

2. The feed table should be in the normal operating

position.

3. Close the main and Pull roll nips. Rollers should

be closed.

4. Speed is set to 3 or less and “FRONT” ( )

motor direction is selected.

5. Press the “START” ( ) button.

6. Set main roller pressure between 40% – 60% for

laminating by turning the main roll lift handle.

CAUTION: If using PSA film, an air pocket may

result between the main rollers and pull rollers.

Raise the pull rollers to allow the air Pocket to

pass.

7. Make any necessary film brake tension

adjustments, pull/main roller pressure, and

clutch and/ or rewind brake tension adjustments.

8. Position the item to be laminated on the feed

table.

9. Align the leading edge of the item parallel to the

heat roller nip (Fig. 25).

10. With both hands and an outward force push the

image slower than the speed of the rollers into

the nip of the heat rollers (Fig. 26).

CAUTION: Avoid forcing the image into the

main roller nip as this action will cause the

corners of the leading edge to buckle and create a

wave.

GBC 3064WF Operation Manual

(2)

A

.......a PSA film or mount adhesive

(2)

(1)

.......a PSA film or mount adhesive

B

Figure 27

Method for Tacking New Film to Existing Film

The following describes a method for loading film

whereby the existing film present on the heat

rollers may be used in place of the threading card

to draw the new film through the laminator. The

adhesive of the existing film must be tacky or

liquefied. Leading edges of the new film will be

overlapped onto the tacky adhesive of the old film.

The existing film and the new film will be pulled

through the laminator together.

CAUTION: Do not cut yourself

CAUTION: Be careful not to cut any of the

rollers!

1. Cut (1) remaining top film web between the

idler bar and heat roller. Cut (2) the film web

between the lower film supply and the idler

bar (Fig. 27).

2. Tilt the feed table down.

3. Do not allow the adhesive side of the film to

contact the heat or pull rollers. Liquefied or

tacky adhesive deposited on heat rollers will

require the rollers to be cleaned per the section

tilted “MAINTENANCE “.

4. Replace both the top and bottom rolls of film

with new rolls. Ensure the adhesive side is

facing out.

5. Pull the film around the idler bars, with the

exception of PSA mounting adhesives without

a release liner.

6. Tack the new film to the existing film on the

heat rollers. For PSA film, attach the release

liner to the rewind tube

7. Use the footswitch to advance the film into the

heat roller nip.

8. Observe the film being pulled through the

laminator to assure that the remaining existing

film and the new films are advancing

concurrently. Any separation between the

films will require stopping the motor

immediately and the situation corrected.

9. Press “STOP” ( ) once the newly threaded

film has completely exited the pull rollers.

La page charge ...

MyBinding GBC Falcon 3064-1 Manuel utilisateur

Ce manuel convient également à

MyBinding GBC Falcon 3064-1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents