Philips FW-R55 Le manuel du propriétaire

CDR Mini Hi-Fi System

FW-R55

2

Important notes for users in the U.K.

Mains plug

This apparatus is ﬁtted with an approved 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1 Remove fuse cover and fuse.

2

Fix new fuse which should be a BS1362

5 Amp,A.S.T.A.or

BSI approved type.

3 Reﬁt the fuse cover.

If the ﬁtted plug is not suitable for your socket outlets,it

should be cut off and an appropriate plug ﬁtted in its place.

If the mains plug contains a fuse,this should have a value

of 5 Amp.If a plug without a fuse is used, the fuse at the

distribution board should not be greater than 5 Amp.

Note:The severed plug must be disposed of to avoid a

possible shock hazard should it be inserted into a

13Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the

following code:blue = neutral (N),brown = live (L).

00

As these colours may not correspond with the colour

markings identifying the terminals in your plug,proceed

as follows:

– Connect the blue wire to the terminal marked N or

coloured black.

– Connect the brown wire to the terminal marked L or

coloured red.

– Do not connect either wire to the earth terminal in

the plug,marked E (or e) or coloured green (or green

and yellow).

Before replacing the plug cover,make certain that the

cord grip is clamped over the sheath of the lead - not

simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require consent.

See

Copyright Act 1956 and The Performer’s Protection

Acts 1958 to 1972.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio FW-R55 Philips risponde

alle prescrizioni dell’art.2 comma 1 del D.M.

28 Agosto 1995 n.548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips,Glaslaan 2

5616 JB Eindhoven,The Netherlands

Norge

Typeskilt ﬁnnes på apparatens bakside.

Observer:Nettbryteren er sekundert innkoplet.

Den innebygde netdelen er derfor ikke frakoplet

nettet så lenge apparatet er tilsluttet

nettkontakten.

For å redusere faren for brann eller elektrisk støt,skal

apparatet ikke utsettes for regn eller fuktighet.

3

EnglishFrançaisEspañolDeutsch

English

_________________________________________________________

4

Français

_______________________________________________________

28

Español

________________________________________________________

52

Deutsch

_______________________________________________________

76

Technical data

_______________________________

5

General information

Environmental information

_____________________

5

Supplied accessories

__________________________

6

Setup information

___________________________

6

Maintenance

________________________________

6

Disc handling

_______________________________

6

Discs for recording

___________________________

6

Discs for playback

____________________________

6

MP3

Some words about MP3

______________________

7

Installation

Speaker connections

_________________________

8

Antenna connections

_________________________

8

Mains

_____________________________________

8

Plug and Play

_______________________________

8

Analogue audio connections

___________________

9

Digital audio connections

______________________

9

Connecting a subwoofer

______________________

9

Controls and connections

On the back

_______________________________

10

On the front

_______________________________

11

Remote control

Remote control keys

________________________

12

Remote control usage

_______________________

13

Sound control

______________________________

13

Basic functions

Switching to standby

________________________

14

Demonstration mode

_______________________

14

Loading the CDC and CDR

___________________

14

Playback

__________________________________

15

Selecting and searching

_______________________

15

SHUFFLE and REPEAT

_______________________

16

CD text display

____________________________

16

ID3-tag

___________________________________

16

Program

Programming track numbers

__________________

17

Erasing a track from the program

_______________

17

Clearing the program

________________________

17

Making a program for recording

________________

17

About recording

Basic information

___________________________

18

Direct Line Recording (DLR)

__________________

18

Auto Level Control (ALC)

____________________

18

Adjusting the record level

____________________

18

Internal recording

Recording a single track

______________________

19

Recording an entire CD

______________________

19

Recording a program

________________________

20

Recording from the tuner

_____________________

20

Further recording possibilities

_________________

21

External recording

Analogue or digital recording?

_________________

22

Automatic track increment

____________________

22

Recording with automatic start

________________

22

Manual recording

___________________________

22

(Un)ﬁnalizing,erasing

Finalizing CDR(W) discs

______________________

23

Unﬁnalizing CDRW discs

_____________________

23

Erasing from a CDRW disc

____________________

23

Features

CD text editing (on CD recorder only)

__________

24

Tuner

Tuning to radio stations

______________________

25

Storing radio stations

________________________

25

Tuning to preset stations

_____________________

25

RDS

_____________________________________

25

Clock and timer

Clock setting

______________________________

26

Timer functions

____________________________

26

Troubleshooting

____________________________

27

Contents

4

English

Subject to modiﬁcation without notice.

General

AC Power

________________________

220–230 V/50 Hz

Power consumption

Active

_________________________________

90 W

Standby

______________________________

< 17 W

Economy power save mode

_______________

<1 W

Dimensions,w × h × d

___________

265 × 310 × 411 mm

Weight (without speakers)

____________________

7.6 kg

Ampliﬁer

Output power

________

2 × 120 W MPO, 2 × 60 W RMS,

6 Ω,1 kHz,THD 10%

Frequency response

_____________

20–20,000 Hz,±3 dB

S/N ratio

__________________________

≥ 85 dBA (IEC)

Input sensitivity

AUX/CDR IN L/R (standard level)

________

1,000 mV

AUX/CDR IN L/R (low level)

_____________

500 mV

DIGITALIN

__________

500 mV

pp

(75 Ω)/12–96 kHz

Output

Impedance speakers

______________________

≥ 6 Ω

Impedance headphones

______________

32 Ω–600 Ω

LINE OUT L/R

________________________

500 mV

SUBWOOFER OUT

______________________

2.3 V

CD changer and CD recorder

Number of programmable tracks

_________________

99

Playback

Frequency range

_____________

20–20,000 Hz,±3 dB

S/N ratio

____________________________

≥ 98 dBA

Cross talk

_____________________

≤ -75 dB (1 kHz)

Total harmonic distortion

_________

≤ -80 dB (1 kHz)

Digital recording

____________________

equal to source

Analog recording

Frequency range

_____________

20–20,000 Hz,±3 dB

S/N ratio playback

_____________________

≥ 88 dBA

Cross talk

_____________________

≤ -65 dB (1 kHz)

Total harmonic distortion

_________

≤ -78 dB (1 kHz)

Laser (CD recorder)

Type

___________________

Semiconductor laser GaAIAs

Wave length

___________________

775–795 nm (at 25°)

Output power

________

2.5 mW (Read),35 mW (Write)

Beam divergence

________________________

60 degree

Tuner

Wave range

FM

______________________________

87.5–108.0 MHz

MW

______________________________

531–1,602 kHz

LW

________________________________

153–279 kHz

Speakers

System

__________________________

3 way bass reﬂex

Impedance

__________________________________

6 Ω

Woofers

Woofer

______________________________

1 × 5

1

/

4

"

wOOx woofer

__________________________

1 × 6"

Tweeter

___________________

1 × 2",Ferro ﬂuid cooled

Tweeter

__________________________

1 × 1",Polydome

Dimensions,w × h × d

___________

240 × 350 × 290 mm

Weight

_______________________________

3.9 kg/each

Environmental information

All redundant packing material has been omitted.We have

done our utmost to make the packaging easily separable into

three mono materials: cardboard (box),polystyrene foam

(buffer) and polyethylene (bags,protective foam sheet).

Your set consists of materials which can be recycled if

disassembled by a specialized company.Please observe the

local regulations regarding the disposal of packing materials,

exhausted batteries and old equipment.

As an ENERGY STAR

®

partner,

Philips has determined that this

product meets the ENERGY STAR

®

guidelines for energy efﬁciency.

This set complies with the radio interference

requirements of the European Community.

CAUTION

Use of controls or adjustments or performance of

procedures other than herein may result in hazardous

radiation exposure or other unsafe operation.

Technical data/General information

5

English

CAUTION

INVISIBLELASERRADIATIONWHENOPEN.

AVOIDEXPOSURETOBEAM.

Note:This warning is located inside

the enclosure.

Supplied accessories

– 2 loudspeakers including 2 speaker cables

– Remote control

– 2 batteries for the remote control, size AA

– AM (MW) loop antenna

– FM wire antenna

– Mains cable

Setup information

Place the set on a ﬂat,hard and stable surface.Make sure to

leave at least 3.5 cm free around the set to prevent

overheating.Active mobile phones near to the set may

cause malfunctions.

Maintenance

Clean the set with a soft,

slightly dampened,lint-free cloth.Do

not use any cleaning agents as they

may have a corrosive effect.

Do not expose the set,batteries or

discs to humidity,rain,sand or

excessive heat (caused by heating

equipment or direct sunlight).

Disc handling

If the CDR Mini Hi-Fi system fails to read discs correctly use

a commonly available cleaning-CD to clean the lenses

before submitting the set to repair. Other cleaning methods

may destroy the lenses.Always keep the trays closed to

avoid dust on the lenses.

The lenses may cloud over when the set is suddenly moved

from cold to warm surroundings. Playing a disc is not

possible then.Leave the set in a warm environment until

the moisture evaporates.

To take a disc out of its box easily,

press the centre spindle while lifting

the CD(RW).Always pick up a

CD(RW) by the edge and put it

back in its box after use.

Never write on a CD or attach a

sticker to it.Write only on the printed side of a CDR or

CDRW,and only with a soft felt-tipped pen.

To clean a disc,wipe it in a straight

line from the centre towards the

edge using a soft,lint-free cloth.A

cleaning agent may damage the disc!

Discs for recording

For recording,make sure to use special audio discs only.

These discs are marked with “Digital Audio”and the logos

shown below.

There are two different types of audio discs for the use on

this CD recorder:

– CD-Audio Recordable (CDR)

discs can be recorded on once and

played on all standard CD players and

CD recorders,when ﬁnalized.

– CD-Audio ReWritable (CDRW)

discs can be recorded on,erased and

re-recorded many times and played on

CDRW compatible CD players and

CD recorders,when ﬁnalized.

All Philips CD players and CD recorders with

this sticker are CDRW compatible.

To ensure proper working of the set we

recommend the use of Philips audio CDR and audio

CDRW discs only.

Note: Do not use a computer CDR or CDRW as recording will

not work properly!

Recording is permissable insofar as copyright or

other rights of third parties are not infringed upon.

In some countries the use of the Philips CDR Mini

Hi-Fi system as shown or suggested in this user manual

may require the authorization of copyright holders.

Discs for playback

For playback on this CD changer and CD recorder you can

use following discs:

– All pre-recorded audio CDs

– All audio CDR and audio CDRW discs

– MP3-CDs (CD-ROMs with MP3 tracks) – Make

sure ﬁlename ends with .mp3

Note:Not ﬁnalized CDR(W) discs can only be played on the

CD recorder.

General information

6

English

Some words about MP3

The revolutionary new music compression technology MP3

(MPEG Audio Layer-3) enables shrinking down of original

digital audio sound data with a factor of up to 10 without

losing signiﬁcant sound quality.This allows you to record up

to 10 hours of CD-like quality music on a single CD-ROM.

Making your own MP3-CD

Basically there are two sources for MP3 music on CD.You can

either transfer music from your own digital audio CDs via

CD-ROM drive onto your PC and encode it into MP3 format

(“rip”) or download legal MP3 music from the Internet.

Record (“burn”) the music from your hard disc on CD-ROM

with your home PC (make sure ﬁlename ends

with .mp3).Once ﬁnished,you can play your MP3-CD on

this CDR Mini Hi-Fi system and enjoy the music.

Data rate

The data rate is of great importance with MP3.It indicates

how fast bits are transfered.

Stereo music on a CD shows a data rate of about

1,400 kilobits per second (kbps).To achieve a good MP3

quality a bit rate of 128 kbps is recommended.As

the encoding rate is user-selectable,make sure to reach this

data rate for MP3 as recordings less than 128 kbps will suffer

from a degradation in sound quality.

Recording

Downloading MP3 ﬁles from the Internet or ripping songs

from your own digital audio CDs is a delicate process, also

inﬂuenced by the quality of the encoder program and

speed of your PC.This may sometimes result in “drop-outs”

which you may experience while listening to your MP3-CD.

In any case make sure to use a recording speed not faster

than indicated on the CD-ROM and avoid running other

programs simultaneously on your PC during the recording

process.

In compliance with the SDMI (Secure Digital

Music Initiative) this CDR Mini Hi-Fi system has no

digital output.

It is not possible to “burn” an MP3-CD on this

CDR Mini Hi-Fi system.

It is not possible to record from an MP3-CD.

Supported formats

Following formats are supported on this CDR Mini Hi-Fi system:

– Disc format:ISO 9660 or Joliet

– Filename: .mp3 (tracks), .m3u or .pls (playlists)

– Bit rate: 32–320 kbps (128 kbps advised) or variable

bit rate

Use ISO 9660 disc format when burning the CD-ROM.

UDF disc format (e.g.“DirectCD” or

“WinOnCD”) is not supported.

MP3

7

English

Speaker connections

The speaker connections are click-ﬁt connectors.Use them

as shown below.

1 Connect the coloured (or marked) wire to the red terminal

and the black (or unmarked) wire to the black terminal.

2 Connect:

– Left speaker to L (red and black)

– Right speaker to R (red and black)

Antenna connections

AM antenna

The loop antenna supplied is for indoor use only.

1 Fit the plug of the loop antenna to AMANTENNA as

shown below.

2 Position the antenna as far away as possible from the TV,a

VCR and other radiation sources.

3 Turn the antenna for optimum reception.

FM antenna

The wire antenna supplied can only be used to receive

nearby stations.For better reception we recommend using

a cable antenna system or an outdoor antenna.

1 Fit the supplied wire antenna to FM ANTENNA as shown

below.

2

Move the antenna in different positions for optimum reception.

00

If you are using a cable antenna system or an outdoor

antenna,ﬁt the antenna plug to FM ANTENNA instead of

the wire antenna.

Mains

The type plate is located on the rear of the set.

1 Check whether the mains voltage as shown on the type

plate corresponds to your local mains voltage. If it does not,

consult your dealer or service organization.

2 Make sure all connections have been made before

switching on the mains supply.

3 Connect the mains cable supplied to AC MAINS ~ and to

the wall socket.This switches on the mains supply.

When the set is switched to standby,it is still consuming some

power.To disconnect the set from the mains completely,

remove the mains plug from the wall socket.

For users in the U.K.:please follow the instructions on

page 2.

To avoid overheating of the set a safety circuit has

been built in.Therefore your set may disconnect

under extreme conditions. If this happens,switch the

set off and let it cool down before reusing it.

Plug and Play

This function allows you to store all available radio stations

automatically.

First setup

1 When you switch on the mains supply AUTO INSTALL -

PRESS PLAY will be scrolled.

2 Press ÉÅ to start storing.

➜ INSTALL is displayed, followed by TUNER and AUTO.

➜ PROG starts ﬂashing.

➜ All RDS stations,followed by all other FM stations and all

other stations of other wavebands with sufﬁcient signal

strength,will be stored.

Note:If no stereo signal is detected CHECK ANTENNA will be

displayed.Check antenna connection or turn the antenna for

optimum reception.

3 When all available radio stations are stored or the memory

for 40 presets is full,storing will be stopped and the last

stored radio station will be played.

00

To exit the automatic storing press Ç.

Note:If you exit automatic storing before completion,the function

will be restarted when switching on the mains supply again.

Restarting Plug and Play

1 Press ÉÅ for minimum 5 seconds in standby or

demonstration mode.

➜ AUTO INSTALL - PRESS PLAY will be scrolled.

2 Press ÉÅ to restart storing.

➜ INSTALL is displayed, followed by TUNER and AUTO.

➜ PROG starts ﬂashing.

➜ All previously stored stations will be replaced.

Installation

8

English

AM ANTENNA FM ANTENNA

N

TENNA FM ANTENNA

Analogue audio connections

AUX/CDR IN L/R

It is possible to use an additional appliance, e.g. tape

recorder,TV or VCR,with the set.

1 Connect the red plug of a cinch cable to the red socket

AUX/CDR IN R and the white plug to the white socket

AUX/CDR IN L.

2 Connect the other end of the cinch cable to the audio

outputs of the additional appliance.

3 Press AUX repeatedly to select the analogue input for the

appliance.

➜ AUX ANALOG H:for standard level input sources

➜ AUX ANALOG L:for low level input sources (when

sound of external source is too low compared to the

internal tuner or CD changer)

4 Operate your appliance as usual and adjust volume and

sound with the set.

It is not possible to connect a turntable directly to

AUX/CDR IN L/R.If you wish to use a turntable

with the set,you have to connect an ampliﬁer to

AUX/CDR IN L/R on the set.Then connect the

turntable to the ampliﬁer.

LINE OUT L/R

You can use these outputs for playback or recording on any

analogue audio equipment,e.g. ampliﬁer or tape recorder.

● Use a cinch cable to connect the analogue audio inputs of

the additional appliance with LINE OUTL/R on the set and

operate your appliance as usual.

Digital audio connections

DIGITAL IN

You can use this coaxial input for recordings from any digital

audio equipment with a digital coaxial output e.g.CD player

or DVD player.

1 Use a coaxial cable to connect the coaxial output of the

additional appliance with DIGITALIN on the set.

2 Press AUX repeatedly to select the digital input for the

appliance.

➜ AUX DIGITAL is displayed.

3 Operate your appliance as usual.

Connecting a subwoofer

A subwoofer can be used to enhance the bass

performance of your set dramatically.

1 Use a cinch cable to connect the input of the subwoofer

with SUBWOOFER OUT on the set.

2 Follow the instructions supplied with the subwoofer.

Installation

9

English

RL

LINE

OUT

AUX/

CDR

IN

SUBWOOFER

OUT

AM ANTENNA FM ANTENNA

DIGITAL

IN

AC

MAINS

SPEAKERS 6 Ω

CD PLAYER

TAPE RECORDER

SUBWOOFER

~

On the back

1 SPEAKERS 6 Ω L/R

connect to the supplied speakers

2 AC MAINS ~

After all other connections have been made,connect

the mains lead to the wall socket.

3 DIGITAL IN

connect to the coaxial output of a digital appliance

4 FM ANTENNA

connect the supplied wire antenna here

5 AM ANTENNA

connect the supplied loop antenna here

6 LINE OUT R/L

connect to the analogue audio input of an additional

appliance

7 AUX/CDR IN R/L

connect to the analogue audio output of an additional

appliance

8 SUBWOOFER OUT

connect to the input of a subwoofer

Controls and connections

10

AM ANTENNA FM ANTENNA

D

IG

IT

A

L

IN

AC

MAINS

~

2

45

8

R

L

IN

E

O

U

T

A

U

X

/

C

D

R

IN

SUBWOOFER

OUT

C

D

C

H

A

N

G

E

OPEN

•

CLOSE

ST

A

N

DB

Y

•

O

N

E

C

O

P

O

W

E

R

DISPLA

Y/ RDS

CLOCK

•

TIMER

C

D

R

E

C

O

R

D

E

R

C

D

R

O

P

E

N

•

C

L

O

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

O

P

Y

C

D

COMPILE

CD

RECORD

FIN

A

LIZE

ER

ASE

J

O

G

C

O

N

T

R

O

L

@$%

()¡™≤∞

!

C

D

O

N

•

O

F

&^ 76 3

1

£*

9

≥§

#

C

D

R

C

D

1

C

D

2

C

D

3

T

U

N

E

R

A

U

X

SOURCE

0

L

E

V

E

L

On the front

9 wOOx LEVEL

selects the desired wOOx level 1,2 or 3

0 wOOx ON·OFF

switches the wOOx effect on/off

! OPEN·CLOSE

opens/closes the CD changer drawer

@ CLOCK·TIMER

selects the clock or timer functions

# display

$ DISPLAY/RDS

CDC,CDR:selects display information/text

TUNER:switches through RDS information

% CD CHANGE

opens the CD changer drawer,rotates the tray once

^ 2 STANDBY·ON

switches the set to standby

& ECO POWER

switches the set to eco-standby

* p

3.5 mm headphone socket

Note:Connecting the headphones will switch off the speakers.

( Source selection – SOURCE

CDR

selects the CD recorder

CD1,CD2, CD3

selects the CD changer,switches to CD 1,CD 2 or CD 3

TUNER

selects the tuner

AUX

selects the input for an additional appliance

) Multiple function control – rotary control:

í JOG CONTROL ë

selects the previous/next menu item

CDC,CDR:selects the previous/next track

TUNER: selects the previous/next preset tuner station

Multiple function control – keys to press:

à SEARCH

CDC,CDR:searches backward,reviews the tracks in a

program

TUNER:tunes to a lower radio frequency

á SEARCH

CDC,CDR:searches forward,reviews the tracks in a

program

TUNER:tunes to a higher radio frequency

YES/ENTER

conﬁrms a selection

ÉÅ

starts/interrupts playback

REC LEVEL

activates the rotary control for record level adjustment

CD TEXT/EDIT

switches through CD text information, enters/exits the text

edit menu

PROG

enters/exits the program menu

Ç

stops playback/recording

NO/CANCEL

cancels a selection

¡ COPY CD

selects high speed recording and automatic ﬁnalizing of

current CD

COMPILE CD

selects high speed recording and automatic ﬁnalizing of

current program

™ FINALIZE CD

ﬁnalizes/unﬁnalizes recordings

£ RECORD

enters the recording menu

≤ ERASE CD

enters the erasing menu

∞ Sound control – rotary control:

MASTER VOLUME

adjusts the volume

Sound control – keys to press:

DSC

selects predeﬁned sound settings

VAC

selects predeﬁned surround sound settings

INCREDIBLE SURROUND

creates an incredibly wide stereo effect

§ CD RECORDER

CD recorder drawer

≥ / CDR OPEN·CLOSE

opens/closes the CD recorder drawer

Controls and connections

11

English

Remote control keys

1 2

switches the set to standby

2 CDR,CD1, CD2, CD3, TUNER,AUX

select the sources

3 SLEEP

activates the sleep timer

4 TIMER ON/OFF

activates/deactivates the timer

5 DISPLAY

selects display information/text

6 CD TEXT/edit

switches through CD text information, enters/exits the text

edit menu

7 TRACK INCR.

selects automatic or manual increment of a track

8 PROGRAM

enters/exits the program menu

9 REPEAT

repeats a track, an entire CD(RW) or a program

0 SHUFFLE

plays tracks in random order

! DIM

controls brightness of display

@ MUTE

switches the sound off/on

# INCR.SURR.

switches incredibly wide stereo effect on/off

$ -VOLUME

decreases the volume

% +VOLUME

increases the volume

^ É

starts playback

& ë

selects the next menu item

CDC,CDR:selects the next track

TUNER:selects the next preset tuner station

* í

selects the previous menu item

CDC,CDR:selects the previous track

TUNER:selects the previous preset tuner station

( Ç

stops playback

) à

CDC,CDR:searches backward

TUNER:tunes to a lower radio frequency

¡ á

CDC,CDR:searches forward

TUNER:tunes to a higher radio frequency

™ Å PAUSE

interrupts playback/recording

£ YES

conﬁrms a selection

≤ NO

cancels a selection

∞ WOOX ON/OFF

switches the wOOx effect on/off

§ WOOX LEVEL

selects the desired wOOx level 1,2 or 3

≥ VAC

selects predeﬁned surround sound settings

• DSC

selects predeﬁned sound settings

Remote control

12

English

CDR

CD1 CD2 CD3 TUNER

AUX SLEEP

TIMER ON/OFF

TRACK INCR. CD TEXT/edit

DISPLAY

PROGRAM REPEAT

SHUFFLE

MUTE

VOLUME

NO

PAUSE

YES

INCR.SURR.

WOOX

ON/OFF

1

#

2

3

4

6

5

7

8

9

∞

@

§

!

$

%

*

^

&

¡

)

™

0

(

≤

£

WOOX

LEVEL

DSC VAC

DIM

•

≥

Remote control usage

Open the battery compartment

of the remote control and insert

2 alkaline batteries, type AA (R06,

UM-3).

Do not use old and new or different

types of batteries in combination.

Remove batteries if they are empty or if the remote

control will not be used for a long time.

Batteries contain chemical substances,so they should

be disposed of properly.

The buttons on the remote control work the same way as

the corresponding ones on the set.

Note:Always press the source key of the source you wish to

control (e.g.CD1) before selecting the desired function key

(e.g.ÉÅ).

Sound control

Volume adjustment

● Adjust the volume by using MASTER VOLUME.

➜ The current volume level is displayed.

Incredible Surround

Stereo sound is determined by the distance between the

front speakers.Incredible Surround enables you to enjoy an

incredibly wide stereo effect,regardless of the speakers’

distance.

● Press INCREDIBLESURROUND to switch the surround

sound effect either on or off.

➜ INCREDIBLE SURROUND is displayed if the surround

sound effect is on.

Note:The effect of Incredible Surround may vary with different

types of music.

Optimal Sound

For optimal sound listening,you can adjust only one of the

following sound controls at a time:DSC or VAC.

DSC

Digital Sound Control enables you to select predeﬁned

sound settings.

● Press DSC repeatedly to select the desired sound setting.

➜ Either DIGITAL,ROCK, POP,NEW AGE,CLASSIC or

ELECTRIC is displayed.

Note:For a neutral sound select CLASSIC.

VAC

Virtual Ambience Control enables you to select

predeﬁned surround sound settings.

● Press VAC repeatedly to select the desired surround sound

setting.

➜ Either HALL,CINEMA, ARCADE,CONCERT,DISCO or

CYBER is displayed.

wOOx

This feature enables you to select a deep and powerful bass.

● Press wOOx ON·OFF repeatedly to switch the wOOx

effect either on or off:

➜ WOOX OFF:the wOOx effect is switched off.

➜ WOOX LEVEL 1 (or 2,3): the wOOx effect is switched

on and the current level is displayed.

00

To select another of the 3 possible wOOx levels press

wOOx LEVEL repeatedly until the desired level is displayed:

➜ Either WOOX LEVEL 1,WOOX LEVEL 2 or

WOOX LEVEL 3 is displayed.

MUTE

This feature allows you to temporarily switch off the sound

without switching off the set.

1 Press MUTE on the remote control to switch off the sound.

➜ MUTE is displayed and playback/recording will be

continued without sound.

2 Press MUTE on the remote control again to switch on the

sound again.

Remote control/Sound control

13

M

ASTER

VOLUME

C

O

M

P

IL

E

C

D

E

C

O

R

D

ERASE

C

D

ON

•

OFF

LEVEL

A

U

X

English

Switching to standby

● To switch the set on press 2 STANDBY·ON on the set.

● To switch the set to standby press 2 STANDBY·ON

again.

➜ The set is switched to standby and the time is displayed.

● To switch the set to eco-standby press ECO POWER

on the set (or 2 on the remote control for 3 seconds).

Demonstration mode

The demonstration mode displays various features of the

set and will start automatically.

● To cancel the demonstration mode keep Ç on the

set pressed for at least 5 seconds.

➜ The demo mode is cancelled permanently.The set

switches to standby.

Loading the CDC and CDR

Important!

1) This system is designed for regular CD(RW)s.

Therefore,do not use any accessories such as disc

stabilizer rings or CD treatment sheets, etc.as offered

on the market,because they may cause jamming of

the changer mechanism.

2) Do not load more than one disc into one disc

tray.

1 CD changer: Press OPEN·CLOSE to open the

CD changer drawer.

➜ OPEN CHANGER is displayed, the drawer is opened and

the tray rotates once.

CD recorder: Press / CDR OPEN·CLOSE to open the

CD recorder drawer.

➜ OPEN CDR is displayed and the drawer is opened.

Note:Opening the CD changer or CD recorder clears any

program.

2 CD changer:You can load up to 3 discs.Insert a disc

(printed side up) in the right tray.

00

You can load another disc in the left tray.

00

To insert a third disc press CD CHANGE on the set.

➜ The CD carousel will rotate once.

CD recorder: Insert a disc (printed side up) in the tray.

3 CD changer: Press OPEN·CLOSE again to close the drawer.

➜ The drawer is closed and READING is displayed.

➜ CD,the disc tray number, the total number of tracks and

the total playing time of the disc in the last selected tray

are displayed.

CD recorder: Press / CDR OPEN·CLOSE to close the drawer.

➜ The drawer is closed and READING is displayed.

➜ If an unﬁnalized disc is loaded,INITIALIZING will be

displayed.

➜ CDR,the total number of tracks and the total playing

time of the disc are displayed.

MP3-CD only:

➜ READING MP3 is displayed. MP3 is shown.

➜ The ﬁrst album name is displayed.

Basic functions

14

English

CD CHANGE

OPEN

•

CLOSE

S

TA

N

D

B

Y

•

O

N

E

C

O

P

O

W

E

R

D

IS

P

L

A

Y/R

D

S

C

L

O

C

K

•

T

IM

E

R

SOURCE

CD RECORDER

CDR

OPEN•CLOSE

M

ASTER

VOLUME

C

OPY

CD

C

O

M

P

IL

E

C

D

R

E

C

O

R

D

FINALIZE

ERASE

J

O

G

C

O

N

T

R

O

L

CD

O

N

•

O

F

L

E

V

E

L

C

D

R

C

D

1

C

D

2

C

D

3

T

U

N

E

R

A

UX

Playback

1 Press either CD1,CD2, CD3 or CDR to select a particular

disc.

2 Press ÉÅ to start playback.

➜ CD1 (or 2,3) or CDR,the current track number and

elapsed playing time are displayed.

00

To switch through the following information press DISPLAY

repeatedly on the set:

➜ track number,remaining playing time of current track

➜ track number,remaining playing time of disc

➜ track number,actual playing time of current track

3 Press Ç to stop playback.

➜ CD1 (or 2,3) or CDR,the total number of tracks and the

total playing time of the disc are displayed.

00

You can interrupt playback by pressing ÉÅ.

➜ The time where playback was interrupted blinks.

00

To resume playback press ÉÅ again.

Selecting and searching

Selecting a track when playback is stopped (on all

discs except MP3-CDs)

1 Rotate í JOG CONTROL ë to skip to the desired track

number.

2 Press ÉÅ to start playback.

➜ Playback starts with the selected track.

Selecting an album and/or a track when playback

is stopped (on MP3-CDs only)

1 Insert an MP3-CD (printed side up) in the CD changer or

recorder.

➜ READING MP3 is displayed. MP3 is shown.

➜ The ﬁrst album name is displayed.

2 Rotate í JOG CONTROL ë to skip to the album

number you wish to select.

➜ ALBUM is shown and the album number is displayed.

3 As soon as the desired album number is displayed,stop

rotating í JOG CONTROL ë.

➜ The album name is scrolled.

4 If you want to start playback of the entire album:

Press ÉÅ.

➜ Playback of the entire album starts.

If you want to enter the album:

Press YES.

Rotate í JOG CONTROL ë to skip to the track

number you wish to select.

➜ TRACK is shown and the track number is displayed.

As soon as the desired track number is displayed,stop

rotating í JOG CONTROL ë.

➜ The track name is scrolled.

Press ÉÅ to start playback.

➜ Playback starts with the selected track.

To exit the album and to return to the album selection

press NO.

Notes:

At the end of your album selection you will recognize an

album called VARIOUS.This album contains all tracks which

were not saved in an album when making the MP3-CD.

If you want to play a playlist which you created on your

MP3-CD when making it,you have to select it directly by

rotating í JOG CONTROL ë and pressing ÉÅ then.

Selecting a track during playback

● Rotate í JOG CONTROL ë to skip to the beginning of

the previous or next track on the selected disc.

➜ Playback continues with the selected track.

Searching for a passage during playback

1 Keep à SEARCH or á SEARCH pressed to ﬁnd a

particular passage in backward or forward direction.

➜ Searching is started and playback continues at a low

volume.After 5 seconds the search speeds up with

volume muted.

2 Release the key at the desired passage.

➜ Normal playback continues.

Basic functions

15

English

D

IS

P

L

A

Y/R

D

S

C

L

O

C

K

•

T

IM

E

R

SOURCE

C

D

R

E

C

O

R

D

ER

C

D

R

O

P

E

N

•C

LO

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

O

P

Y

C

D

C

O

M

PIL

E

C

D

RECORD

F

IN

A

L

IZ

E

R

A

S

E

JOG

CONTROL

C

D

O

N

•

O

FF

LEV

E

L

C

D

R

C

D1

C

D

2

CD3

TUNER

A

U

X

SHUFFLE and REPEAT

Repeating a track,a disc or a program

1 Press REPEAT repeatedly on the remote control during

playback to select either:

➜ REP TRACK:The current track is played repeatedly.

➜ REP DISC:The entire selected disc is played repeatedly.

➜ REP ALL:All discs in the set (or the program) are (is)

played repeatedly.

Notes:

REP DISC is not possible during SHUFFLE or while playing a

program.

REP TRACK is not possible during SHUFFLE.

2 Playback starts in the chosen mode.

00

To return to normal playback press REPEAT on the remote

control until the display indication disappears.

Playing tracks in random order

● Press SHUFFLE on the remote control during playback.

➜ SHUFFLE is shown and either all tracks of the program or

of all loaded disc(s) in the CD changer and CD recorder

are played in random order.

00

To return to normal playback press SHUFFLE on the

remote control again.

CD text display

This feature allows you to display information such as album

title or track title contained on a specially encoded CD.

● Make sure to insert a CD with CD text.

➜ CD TEXT is shown and the album title and album artist’s

name is scrolled once.

CD text when playback is stopped

● Press CD TEXT/EDIT to see the following information,

which will be scrolled once (if available):

– Album artist’s name

– Album title

CD text during playback

● Press CD TEXT/EDIT to see the following information,

which will be scrolled once (if available):

– Track artist’s name

– Track title

ID3-tag

This feature allows you to display information such as album

title or track title contained on an MP3-track.

● If you created an ID3-tag on your MP3-CD,press

CDTEXT/EDIT during playback to show the following

ID3-tag information:

➜ Album title

➜ Track artist’s name

➜ Track title

Basic functions

16

English

C

OPY

CD

C

OM

PILE

CD

RECORD

FINALIZE

ERASE

JO

G

C

O

N

T

R

O

L

CD

Programming track numbers

You can select up to 99 tracks and store them in the

memory.It is possible to store any track more than once.

1 Load the desired disc(s) in the disc tray(s).

2 Press either CD1,CD2, CD3 or CDR to select a disc.

3 Press PROG to enter the program menu.

➜ PROG starts blinking and PROGRAM is displayed.

4 Rotate í JOG CONTROL ë to select either:

➜ CD1 (or 2,3) and track number or CDR and track

number:The track number of CD1 (or 2,3) or the track

number of the disc in the CD recorder will be

programmed.

or (for audio CD(RW)´s only):

➜ CD1 (or 2,3) ALL or CDR ALL:All tracks of CD1 (or

2,3) or all tracks of the disc in the CD recorder will be

programmed.

5 Press YES to store your selection in the memory.

➜ The number of programmed tracks (STEP),PROG and

the total program time are displayed.

6 Select and store all desired tracks in this way.

7 Press PROG to end up programming.

➜ PROG stays shown and the program is currently available.

Notes:

If you try to store more than 99 tracks,PROGRAM FULL

will be displayed.

A program with MP3 tracks can only be created from one

MP3-CD.

Erasing a track from the program

1 If necessary press Ç to stop playback.

2 Press either CD1,CD2, CD3 or CDR to select a disc.

3 Press PROG,followed by à SEARCH or á SEARCH to

move through the program steps.

➜ The track number at the selected step and the total

program time are displayed.

4 Press NO to remove the track from the program.

➜ CLEARED is displayed brieﬂy.

➜ The next programmed track number will move up to

this position and is displayed together with the step

number and the remaining total program time.

Clearing the program

1 If necessary press Ç to stop playback.

2 Press NO.

➜ CLEAR PROG? is displayed.

3 Press YES to clear the program.

➜ PROG CLEARED is displayed and PROG goes off.

Making a program for recording

1 Select and store all desired tracks from the CD changer

(see “Programming track numbers”).

2 Enter the recording menu (see “Internal recording”).

00

If the total time of the program is of bigger size than the

remaining recording time of the CDR(W):

➜ DOES NOT FIT will be displayed brieﬂy,followed by

the remaining recording time and RECORD PROG?.

If you nevertheless start recording,only those tracks of the

program that ﬁt onto the CDR(W) will be recorded in

their entirety.

00

To change the program press NO.

➜ PROGRAM will be displayed brieﬂy,PROG and the total

playing time of the program will start blinking.Now you

can change the program (see “Programming track

numbers”,“Erasing a track from the program”and

“Clearing the program”).

Note:If you try to use a program for recording which contains

tracks from the CD changer and CD recorder 4 DISC PROG

and CLEAR PROG? will be displayed.Press either NO to exit

or YES to clear the current program and prepare a new one.

Program

17

English

D

IS

P

L

A

Y

/R

D

S

C

L

O

C

K

•

T

IM

E

R

SOURCE

C

D

R

EC

O

R

D

E

R

C

D

R

O

P

E

N

•C

LO

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

O

P

Y

C

D

C

O

M

P

IL

E

C

D

RECORD

F

I

N

A

L

I

Z

E

R

A

S

E

JOG

CONTROL

C

D

O

N

•

OFF

LE

V

EL

C

D

R

CD1

CD

2

C

D

3

TUN

ER

A

U

X

Basic information

The CD recorder deck offers you 3 main functions:

– Recording from the internal CD changer and tuner or

from a selected external source

– Finalizing your CDR(W) discs and unﬁnalizing your

CDRW discs

– Erasing a CDRW disc

The recording procedure is the same for CDR and CDRW

discs.Make sure the CDR(W) is absolutely free of

scratches and dust particles.

For recordings,the minimum track length is 4 seconds.You

can record up to a maximum of 99 tracks on a disc.The

minimum of recording time left on the disc is 7 seconds.

Otherwise DISC FULL is displayed and you cannot enter

the record mode.

Do not forget to ﬁnalize! Finalizing a CDR(W) disc is

a simple procedure, necessary to:

– play a recorded CDR on a standard CD player,or

– play a recorded CDRW on a CDRW compatible

CD player and CD recorder.

Copyright protection

The Serial Copy Management System (SCMS) prevents

the making of a digital copy from a digital copy.The system

allows making a digital recording from the original,however,

in some countries this may require the authorization of

copyright holders.

When you try to record copy protected material from an

external source, COPY PROTECT will be displayed. No

further digital recording is possible then.

When you try to record copy protected material from the

internal CD changer no digital recording is possible,however,

the CD recorder will automatically switch to analogue

recording.It is not possible to copy an MP3-CD.

Recording CD text

If the original CD has CD text, this text will be recorded

automatically, provided that the CD text is not copy

protected.In that case, recording of CD text will not be

possible then and TEXT PROTECT will be displayed.

Direct Line Recording (DLR)

The CD recorder is equipped with the high-performance

Direct Line Recording technique.It ensures a perfect

recording of the source material, meaning a true “bit for

bit”recording. DLR will not become active when ALC is

being used or the record level is adjusted.

Auto Level Control (ALC)

Auto Level Control ensures that the tracks on the

recorded disc have a similar volume level.At all times the

already recorded tracks of the CDR(W) disc will be taken as

reference for the volume level of the following recordings.

Auto level control becomes active,when:

– COMPILE CD is being used,

– a disc, a track or a track edit is being high speed

recorded and the CDR(W) has recordings on it,or

– a program (consisting of more than one disc) from the

CD changer is being high speed recorded.

Auto level control will not become active,when:

– using COPYCD,

– making recordings from the FM tuner,

– making recordings from an external source, or

– making normal recordings in listen mode.

Switching ALC permanently off

1 If necessary,press Ç to stop playback.

2 Press CDR to select the CD recorder.

3 Press REC LEVEL to select:

➜ ALC OFF:ALC is permanently switched off.

00

To enable ALC press REC LEVEL again to select:

➜ ALC ON:ALC is enabled.

Adjusting the record level

You can adjust the reference record level for recordings from

the internal CD changer or from an additional appliance.This is

also possible when ALC is active.This feature can be used for

fading your recordings in or out.However,adjusting the record

level from the CD changer only works during recording.

1 Press CD1,CD2 or CD3 during recording to select the CD

changer,or

press AUX repeatedly to select the input of the additional

appliance:

➜ AUX DIGITAL:the digital input is selected.

➜ AUX ANALOG H:the analogue input for a standard level

source is selected.

➜ AUX ANALOG L:the analogue input for a low level

source is selected.

2 Press REC LEVEL on the set to enable the rotary control

to adjust the desired record level.

3 Turn the rotary control to the left to adjust the desired

record level.The loudest sounds in the material to be

recorded should not reach the red levels of the level bar.

➜ The actual record level (in dB) will be displayed.

About recording

18

English

D

I

S

P

L

A

Y

/R

D

S

C

L

O

C

K

•

T

IM

E

R

SOURCE

C

D

R

E

C

O

R

D

E

R

C

D

R

O

P

E

N

•C

L

O

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

O

P

Y

C

D

C

O

M

P

IL

E

C

D

RECORD

F

I

N

A

L

I

Z

E

R

A

S

E

JOG

CONTROL

C

D

O

N

•

O

F

L

E

V

E

L

C

D

R

CD

1

C

D

2

CD

3

TUNER

A

U

X

For internal recordings you can record from the internal

CD changer or tuner.

Recording a single track

Recording a single track during playback

1 Insert a CDR(W) which is absolutely free of scratches and

dust particles in the CD recorder tray.

2 Play your desired track on the CD changer.

3 Press RECORD on the set to enter the recording menu.

➜ REC TR and the tracknumber are displayed.

4 Press either:

YES to start recording,

➜ The arrow lights,RECORDING IN SESSION is shown,

playback and recording start from the beginning of the

selected track and the actual recording time left starts to

count down.

or

NO to continue playback.

Recording an entire CD

High speed recording and automatic ﬁnalizing of

the current disc

1 Insert a CDR(W) which is absolutely free of scratches and

dust particles in the CD recorder tray.

2 Press either CD1,CD2 or CD3 to select the disc you wish

to copy.

3 Press COPYCD on the set to enter the recording menu.

➜ The arrow starts blinking.The remaining recording time

of the CDR(W),the total playing time of the source CD

and RECORD CD1 (or 2,3)? are displayed.

4 Press YES to start recording and ﬁnalizing.

➜ The arrow lights,RECORDING IN SESSION is shown,high

speed recording at a low volume and ﬁnalizing start and

the actual recording time left starts to count down.

Note:If a program was already available before pressing

COPY CD,this will be ignored. PROG goes off and the current

disc will be recorded.After ﬁnishing the recording,PROG is

shown and the program is available again.

Internal recording

19

English

C

O

P

Y

C

D

C

O

M

P

IL

E

C

D

RE

CO

RD

FINALIZE

ERA

SE

J

O

G

C

O

N

T

R

O

L

CD

DIS

PLA

Y/RDS

C

L

O

C

K

•

T

I

M

E

R

SOURCE

CD RECORDER

C

D

R

O

P

E

N

•C

L

O

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

OPY

CD

C

O

M

P

I

L

E

C

D

RECORD

F

IN

A

LIZ

E

R

A

S

E

J

O

G

C

O

N

T

R

O

L

C

D

ON

•

OFF

LEVEL

CDR

C

D

1

C

D

2

C

D

3

T

U

N

E

R

A

U

X

Recording a program

High speed recording and automatic ﬁnalizing

(optional) of the current program

1 Insert a CDR(W) which is absolutely free of scratches and

dust particles in the CD recorder tray.

2 Press COMPILECD on the set to enter the recording menu.

➜ The arrow starts blinking.The remaining recording time

of the CDR(W),the total playing time of the source CD

and RECORD PROG? are displayed.

Note:If no program is available and you press COMPILE CD,

you will enter immediately the program menu.Start your

programming and return to the recording menu by pressing

PROGor COMPILE CD.

3 Press either:

YES to conﬁrm,

or

NO to change the program.

➜ PROG starts blinking.Now you can change the program

(see “Program”) and return to the recording menu by

pressing COMPILECD.

4 AUTO FINAL? is displayed.

Press either:

YES,if the CDR(W) is to be ﬁnalized after recording,

or

NO, if the CDR(W) is not to be ﬁnalized after recording.

➜ The arrow lights,RECORDING IN SESSION is shown,high

speed recording and ﬁnalizing (if selected) start and the

actual recording time left starts to count down.

Recording from the tuner

1 Insert a CDR(W) which is absolutely free of scratches and

dust particles in the CD recorder tray.

2 Press TUNER repeatedly to select the FM tuner.Then select

the desired radio station (see “Tuning to radio stations”).

3 Press RECORD on the set to enter the recording menu.

➜ REC FM TUNER is displayed.

4 Press YES to conﬁrm.

➜ PREPARING and RECORD? are displayed.

5 Press YES to start recording.

➜ The arrow lights,RECORDING IN SESSION is shown,

recording starts and the actual recording time left starts

to count down.

6 Press Ç to stop recording.

Do not forget to ﬁnalize! Finalizing a CDR(W) disc is

a simple procedure, necessary to:

– play a recorded CDR on a standard CD player,or

– play a recorded CDRW on a CDRW compatible

CD player and CD recorder.

Internal recording

20

English

C

OPY

CD

C

O

M

P

IL

E

C

D

RECO

RD

FINALIZE

ERA

SE

J

O

G

C

O

N

T

R

O

L

CD

D

I

S

P

L

A

Y/R

D

S

C

L

O

C

K

•

T

IM

E

R

SOURCE

C

D

R

E

C

O

R

D

ER

C

D

R

O

PE

N

•C

L

O

S

E

M

A

S

T

E

R

V

O

L

U

M

E

C

O

P

Y

C

D

C

O

M

P

IL

E

C

D

RECORD

F

IN

A

L

I

Z

E

R

A

S

E

JOG

CONTROL

C

D

O

N

•

O

F

LE

V

EL

C

D

R

C

D1

CD2

CD

3

TUNER

A

UX

La page charge ...

Philips FW-R55 Le manuel du propriétaire

Philips FW-R55 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents