Powerfist 9094988 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9094988

Taper: Le manuel du propriétaire

V1.0 9094988

Please read and understand all instructions before use. Retain this manual for

future reference.

This page is intentionally left blank.

SPECIFICATIONS

Lift Capacity 12 tons

Lift Capacity 24,000 lb

Min. Lift Height 9 in.

Max. Lift Height 18-1/4 in.

Operation Hydraulic

Saddle Size 1-9/16 in.

Ram Travel 6 in.

Screw Top Adjustment 3-1/8 in.

Base Size 4-7/16 x 5-3/8 in.

Material Steel

INTRODUCTION

The multipositional hydraulic bottle jack is capable of operating in a vertical or

horizontal position and at an angle.

SAFETY

WARNING! Read and understand all instructions before using this tool.

The operator must follow basic precautions to reduce the risk of

personal injury and/or damage to the equipment.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or death

if certain instructions are not followed.

DANGER! This notice indicates an immediate and specic hazard that will result in

severe personal injury or death if the proper precautions are not taken.

WARNING! This notice indicates a specic hazard or unsafe practice that could result in

a serious injury if the proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result in

minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specic hazard or unsafe practice will result in

equipment or property damage, but not personal injury.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 3 www.princessauto.com / 1-800-665-8685

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a dry, safe and secure location to prevent

rust, damage or misuse.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National Standards

Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear protective clothing and gloves designed for the work environment,

materials and tools.

3. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the inuence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

SPECIFIC SAFETY

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specic

function. Do not modify or alter this tool or use it for an unintended

purpose.

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 4

2. Do not use a handle extension for the jack handle.

3. Make sure the load is stable, so it does not shift when lifting or lowering.

4. Do not force the lifting screw past its safety stop, as the screw may come

out of the jack resulting in personal injury or property damage.

5. Once the load is lifted to the desired height, support the load with jack

stands to prevent injury should the multipositional hydraulic bottle jack

fail. Do not work under a load that is supported only by a jack.

6. Do not attempt to move the load while on the multipositional hydraulic

bottle jack. The jack must only be used in a static position for lifting and

lowering loads. Ensure that the load remains stable at all times.

7. Do not push a load o the multipositional hydraulic bottle jack; lower

carefully.

8. Ensure that there are no obstructions under the load and that the area is

clear before lowering the device.

9. Lower the load in a slow and controlled manner to prevent shock loading.

Shock loading may cause the device to fail and lead to property damage

and/or severe personal injuries.

10. Always keep the lifting screw lubricated to allow easy operation and

prevent rust.

LIFTING PRECAUTIONS

WARNING! Ensure that the load is secure and centered on the device. Do

not allow the load to move or tilt as the device may kick out causing

injury to the operator and/or cause the load to fall.

1. Do not exceed the maximum capacity to prevent equipment failure or

damage.

2. Inspect the device before each use. Do not use if it is bent, cracked,

damaged or has been subjected to a sudden or unexpected (shock) load.

3. Ensure that all applicable pins, bolts and nuts are rmly tightened before

using.

4. Use only with accessories rated to handle the forces exerted by the device

during operation. Other accessories may break and forcefully launch

pieces.

5. Do not place your hands between moving components.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 5 www.princessauto.com / 1-800-665-8685

LIFTING AND LOWERING VEHICLES

1. Secure the vehicle before lifting. Set it in parking gear, engage the parking

brake and chock the wheels.

2. Support the vehicle on areas specied by the vehicle manufacturer only.

3. Do not allow people to enter a vehicle that is being lifted or moved.

4. When lifting a vehicle, apply the emergency brake and block all wheels.

5. Immediately after lifting, support the load with jack stands of adequate

capacity. Do not work under a load that is supported only by a jack.

HYDRAULIC PRECAUTIONS

DANGER! Seek immediate medical attention if hydraulic uid under

pressure penetrates your skin. See Injection Injury precautions for

instructions before using a pressurized hydraulic system.

1. Do not touch or handle, hydraulic hoses or components while under

pressure. Hydraulic uid escaping under pressure has sucient force to

penetrate your clothing and skin. A pinpoint hole may inject hydraulic

uid into your body. Seek immediate medical attention if this occurs (see

Injection Injury).

2. Never exceed the hydraulic system’s load capacity (see Specications).

3. Do not adjust the hydraulic system’s relief setting. The settings are preset

by the factory.

4. Hydraulic oil under pressure is hot and can cause a burn injury if touched,

sprayed or spilled. Allow the hydraulic system to cool before conducting

maintenance.

5. Hydraulic components require regular inspection. Release all pressure

from the system before you inspect it. Replace damaged hydraulic parts

with identical manufacturer's components.

6. Do not attempt makeshift repairs to a hydraulic system. Such repairs can

fail suddenly and create a hazardous condition.

7. A damaged or disconnected hydraulic hose under pressure may whip

around and inict personal injury or damage the work area. Secure the

hose to a xed or permanent structure with clamps or cable ties.

8. Hydraulic uid has a combustible ash point of 200°F (93°F). Do not

expose the uid to an ignition source.

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 6

9. Change your clothing immediately if sprayed with hydraulic uid. Store

clothing or rags contaminated with hydraulic uid in an approved metal

safety can with a spring-closing lid and venting designed to contain a re.

10. Only use hydraulic uid in the pump. Do not substitute or mix brake uid,

or any other uid, with the hydraulic uid. This can result in a pump

failure and injure the user or bystander. It may also damage the pump.

INJECTION INJURY

DANGER! Seek immediate, professional medical treatment if uid

penetrates your skin. It may feel like a pricking or sting. Do not wait

for the appearance of symptoms. A toxic reaction can occur from the

exposure. Delay in treatment can lead to amputation or death.

Inform the medical sta that you have a uid penetration injury as soon as you

arrive at the medical facility. The severity of the symptoms will depend on the

type of uid injected. Bring the Safety Data Sheet for the uid with you to the

medical facility if possible.

INJECTION PRECAUTIONS

Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under pressure

from the tool has sucient force to penetrate your clothing and skin. Follow

the precautions below to avoid an injection injury.

1. Always check for leaks wearing a face shield, safety goggles, rubberized

gloves and protective clothes.

2. Release all pressure from the system before you inspect it.

3. Do not use your hands to detect a leak. Use a large piece of wood,

cardboard or paper and watch for discolouration.

4. Replace damaged parts with identical manufacturer's components to

ensure it is rated to handle the pressure.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in a

malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 7 www.princessauto.com / 1-800-665-8685

CONTENTS

Make sure that all items in the contents are included.

• Multipositional Hydraulic Bottle Jack • 2 Piece Handle

IDENTIFICATION KEY

A. Extension Screw

B. Housing

C. Handle

D. Pressure Adjust Screw (do not

remove plastic cap)

E. Release Valve

F. Handle Receiver

G. Pump

H. 2 Piece Handle

OPERATIONS

RAISING A LOAD

WARNING! Do not place any

part of your body under the load without jack stands in place. The

multipositional hydraulic bottle jack is not designed to maintain heavy

loads for long periods of time

1. Place the jack on a hard level surface capable

of handling the load.

2. Close the release valve. Insert the slotted end

of the handle over the valve and twist to the

right.

3. Insert the upper handle into the lower handle.

Insert the handle into the handle receiver.

4. Pump to raise the saddle. Stop just before the

saddle contacts the load’s lift point. Inspect the

saddle’s position and adjust if necessary.

FIGURE 1.

FIGURE

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 8

5. Turn the extension screw to the left to raise the saddle until it contacts

the load.

6. Pump slowly until the saddle is supporting the load. Continue to pump

as normal to lift the load slightly higher than the desired height to allow

placement of the supports.

7. Position supports, like jack stands, if the load will remain above ground

for an extended period. Consult the support device's manual for proper

placement. Also consult the section Raising and Lowering a Vehicle.

8. Twist the valve to the left slowly to allow the ram to retract. Gradually

lower the load onto the supports.

9. Once the supports are carrying the load, open the valve to allow the ram

to retract fully.

LOWERING A LOAD

WARNING! Dynamic shock loads are created by quick opening and

closing of the release valve when lowering the load. The resulting

overload may cause the hydraulic system to fail, which could result

in severe personal injury and/or property damage.

WARNING! Before lowering the load or vehicle, ensure that there are no

obstructions underneath and that all people are standing clear.

1. Insert the slotted handle end over the release valve.

2. Open the valve by gradually twisting to the left. The load will begin to

lower.

3. Twist right to slow and left to increase the rate of descent.

4. Lower the extension screw by turning it clockwise.

5. Remove the jack once the load is on the ground or a support mechanism

like jack stands.

6. The ram should fully retract. If it does not, push down on it until it is

seated.

MULTI-POSITIONAL JACK USES

WARNING! Be careful when working under a jack used as a spreader or

brace. You may suer an impact injury if the jack is dislodged and falls.

Secure the jack in place with a strap or have someone hold and catch

the jack if it falls.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 9 www.princessauto.com / 1-800-665-8685

The multi-positional jack is capable of operating at any angle between the

vertical and horizontal positions. Use the jack as a spreader to push two

objects apart or as a brace to hold an object in place.

1. Determine the distance between the two contact surfaces.

2. Place the jack on the ground and insert the handle into the receiver. Raise

the ram until it is just short of the needed distance.

3. Position the jack so the base is against the sturdier surface.

4. Turn the extension screw until it touches the other surface.

5. Insert the handle into the receiver and pump the handle until the pressure

will hold it in place.

6. Secure the jack if possible to prevent it from falling if it is dislodged.

7. Continue to pump the handle if you need to increase the gap between the

two surfaces, until you reach the desired distance.

8. Perform any tasks you need while the jack is in place.

9. Slowly release the pressure while holding the jack, to prevent it from

falling.

10. Once it is no longer acting as a spreader or brace, place the jack on the

ground and manually force the ram back into the cylinder to protect the

ram from dirt and debris.

RAISING AND LOWERING A VEHICLE

Take these additional steps before following instructions in

Raising a Load and

Lowering a Load

1. Set the vehicle in parking gear and engage the parking brake.

• For vehicles with a manual transmission, engage the parking brake

and leave the car in reverse or 1st gear. Consult your vehicle owner’s

manual for the correct gear.

2. Place wheel chocks that t the wheel curve on either side of the vehicle’s

remaining wheels.

3. Place the jack only on support points or areas specied by the vehicle

manufacturer (consult owner’s manual).

4. Lift the vehicle to a height that leaves enough room to place the jack

stands.

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 10

5. When the work is done, raise the load enough with the jack to carefully

remove the jack stands.

6. Slowly and carefully lower the load.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is ecient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Keep the tool handles or gripping surfaces clean and dry.

4. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

5. Have a qualied technician inspect the jack:

a. Once a year.

b. After receiving a shock load. Take the jack out of service until the

technician certies that it is safe to use.

WARNING! Only qualied service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

HYDRAULIC MAINTENANCE

HYDRAULIC RAM MAINTENANCE

Monthly maintenance is recommended for the hydraulic ram. Any restrictions

due to dirt, rust, etc. can cause the either slow movement or extremely rapid

jerks, damaging the internal components. The following steps are designed to

keep the pump maintained and operational.

1. Lubricate the cylinder and the pumping mechanism with light oil.

2. Visually inspect for cracked welds, bent, loose, missing parts or hydraulic

oil leaks.

3. Inspect the hydraulic ram immediately if it was subjected to an abnormal

load or shock load.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 11 www.princessauto.com / 1-800-665-8685

4. Remove any hydraulic jack pump from service that is damaged, worn

down or operates abnormally, until repaired by an authorized service

technician.

5. Check and maintain the ram oil level.

6. Always store the hydraulic ram in the fully retracted position. This will

help protect critical areas from corrosion.

7. Do not use brake or transmission uids or regular motor oil as they can

damage the seals. Always purchase and use products labeled Hydraulic

Oil.

REFILL THE HYDRAULIC JACK PUMP

The pump may become less ecient when the hydraulic oil level is too low or

contaminated by metal particulate through normal wear-and-tear.

1. Retract the ram and remove the oil ller plug.

2. Check and maintain the ram oil level.

• Check the oil level with the oil dip stick. Use a long plastic cable tie

as a substitute if the unit does not have a dipstick.

3. Fill the cylinder with a high quality hydraulic jack oil, up to the oil plug

opening.

a. Place a funnel into the oil ll neck. The funnel opening should be

wide enough to prevent the oil from collecting in the funnel’s cone.

b. Pour oil into the funnel. Allow the oil to settle for one minute and

recheck the level. Repeat until the desired level is reached.

4. Follow the steps in Bleeding the Hydraulic System.

5. Insert the oil ller plug and hand tighten.

6. Wipe up any spilled oil. Dispose of oil soaked rags in a proper hazardous

waste container.

REPLACE THE HYDRAULIC OIL

Replace the hydraulic oil annually.

1. Relieve pressure from the system by opening the release valve, then

loosening the oil ller plug.

2. Remove the oil ll plug.

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 12

3. Lay the jack on its side and drain the oil into a suitable container. Dispose

of used hydraulic oil in accordance with local by-laws.

4. Stand the jack on its base and wipe o any excess oil.

5. Follow the instructions for Rell the Hydraulic Jack.

BLEEDING THE HYDRAULIC SYSTEM

Bleed excess air from the hydraulic system as follows:

1. Open the release valve by turning it counterclockwise.

2. Remove the oil ller screw and ll the hydraulic jack pump with hydraulic

uid.

3. Wait 5 minutes for trapped air to rise to the surface.

4. Pump the handle for several strokes to eliminate any air in the system.

5. Check the oil ller hole and if necessary, top o with more hydraulic oil.

6. Restore the oil ller screw. Close the release valve by turning clockwise.

7. Test the ram several times for proper operation before putting it into use.

Do not use the ram if it still does not appear to be working properly. Have

a qualied service technician service or repair the hydraulic system.

FLUSHING THE VALVE

Contaminants may block the release valve, causing issues when attempting to

lower a load. Clear the valve with the following steps.

1. Lower the saddle and securely close the release valve.

2. Manually lift the saddle several inches.

3. Open the release valve and force the saddle down as quickly as possible.

LUBRICATION

Inspect and lubricate the tool when required. Only use light oil to lubricate the

tool. Other lubricants may not be suitable and could damage the tool or cause a

malfunction during use.

Clean and lubricate all moving parts.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 13 www.princessauto.com / 1-800-665-8685

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

DO NOT pollute the environment by allowing uncontrolled discharge of

waste oil.

HYDRAULIC FLUID DISPOSAL

Do not drain hydraulic oil into the sewer system or dispose in an uncontrolled

location. Hydraulic uid may take more than a year to breakdown in the

environment and the ingredients may still be toxic. Contact your local

municipality for proper disposal instructions or locations.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualied technician

service the tool.

TROUBLESHOOTING A JACK

Problem(s) Possible Cause Suggested solution

Jack will not lift

load.

1. The release valve is not

closed tightly.

2. Overloaded the jack.

3. Air is trapped in the

hydraulic system.

4. Hydraulic oil level is low.

1. Close the release valve rmly.

2. Reduce load or use a jack with a

greater lift capacity.

3. Bleed air from the system.

4. Check the oil ller hole and if

necessary, top o with more

hydraulic oil.

Jack will lift, but

will not maintain

pressure.

1. The release valve is not

closed tightly.

2. Overloaded the jack.

3. Hydraulic unit is

malfunctioning.

1. Close the release valve rmly.

2. Reduce load or use a jack with a

greater lift capacity.

3. Malfunctions:

a. Replace the seals.

b. Have a qualied technician

service the tool.

Will not lower

after loading.

1. Reservoir is overlled.

2. Linkages are binding.

3. Contaminated release

valve.

1. Drain oil to the proper level.

2. Clean and lubricate all moving

parts.

3. See Care & Maintenance -

Flushing the Valve.

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 14

Problem(s) Possible Cause Suggested solution

Poor lift

performance.

Will not lift to the

max. height.

1. Hydraulic oil level is low.

2. Air is trapped in the

hydraulic system.

1. Add oil to the proper level.

2. Bleed air from the system.

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 15 www.princessauto.com / 1-800-665-8685

PARTS BREAKDOWN

# Description QTY

1 Clip 1

2 Nylon Nut 1

# Description QTY

3 O-ring Seal 1

4 Nylon Nut 1

9094988 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK V1.0

www.princessauto.com / 1-800-665-8685 Page 16

# Description QTY

5 Extension Screw 1

6 Bushing 1

7 Ram 1

8 Ram Cap 1

9 Nylon Bowl 1

10 O-ring Seal 1

11 Circlip 1

12 Oil Reservoir Housing 1

13 Oil Fill Plug 1

14 Cylinder 1

15 Oil Return Valve Rod 1

16 O-ring 1

17 Steel Ball 3

18 Needle Cap 1

19 Pressure Regulating Screw 1

20 O-Ring 1

21 Pressure Regulating Spring 1

# Description QTY

22 Connector 1

23 Ball Ø4 1

24 Base 1

25 Oil Plug 1

26 Pump Cylinder 1

27 Steel Ball 1

28 Nylon Washer 1

29 O-ring 1

30 Split washer 1

31 Plunger 1

32 R-Pin 2

33 Pin 1

34 Rivet 1

35 Connecting Rod 2

36 Handle Receiver 1

37 Lower Handle 1

38 Upper Handle 1

V1.0 MULTI-POSITIONAL HYDRAULIC BOTTLE JACK 9094988

Page 17 www.princessauto.com / 1-800-665-8685

This page is intentionally left blank.

La page est en cours de chargement...

Powerfist 9094988 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9094988

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Powerfist 9094988 Owner's manual

Powerfist 9094988 Le manuel du propriétaire

Powerfist 9094988 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents