Smooth Fitness V390 Manuel utilisateur

USER’S MANUAL

V390 Semi Recumbent Bike

USER WEIGHT LIMITATION: 300lbs(136kgs)

SERIAL NUMBER (found on frame):

2 V 390 SEMI-RECUMBENT BIKE

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your bike.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the bike. It is the responsibility of the owner to ensure that all users of this bike are adequately

informed of all warnings and precautions.

• Use the bike only as described in this manual.

• Place on a level surface. Do not place the bike on any surface that blocks air openings. To protect the floor or carpet from

damage, place a mat under the bike.

• When choosing a location for the bike be sure that the location and position permit access to a plug.

• Keep the bike indoors, away from moisture and dust. Do not put the bike in a garage or covered patio, or near water.

• Do not operate the bike where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the bike at all times.

• The bike should not be used by persons weighing more than 300LBS (136 Kgs).

• Never allow more than one person on the bike at a time. Wear appropriate exercise clothing when using the bike. Do not

wear loose clothing that could become caught in the bike. Athletic support clothes are recommended for both men and

women. Always wear athletic shoes. Never use the bike with bare feet, wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit.

• Always examine your bike before using to ensure all parts are in working order.

• Allow the bike to come to a full stop before stepping off.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your bike.

• The item is suitable for semi-commercial, light-commercial and home usage.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your bike. Do not operate

the bike with a damaged or frayed power cord.

• Always unplug the bike before cleaning and/or servicing. Service to your bike should only be performed by an authorized

service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will

void the bike warranty.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your bike.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

AVERTISSEMENT

: Pour réduire le risque de brûlures, d'incendie, d'électrocution ou de blessures, lire les précautions

suivantes et informations importantes avant d'utiliser le vélo. Il est de la responsabilité du propriétaire de s'assurer

que tous les utilisateurs de ce vélo sont correctement informés de tous les avertissements et les précautions.

• Utilisez le vélo uniquement comme décrit dans ce manuel.

• Placez-le sur une surface plane. Ne pas placer la moto sur une surface qui bloque les ouvertures d'air. Afin de

protéger le plancher ou le tapis de tout dommage, placez un tapis sous la moto.

• Lorsque vous choisissez un emplacement pour le vélo être sûr que l'emplacement et la position de permettre

l'accès à un bouchon.

• Gardez le vélo de l'intérieur, loin de l'humidité et la poussière. Ne pas mettre la moto dans un garage ou un

patio couvert, ou près de l'eau.

• Ne pas faire fonctionner la moto où des produits aérosols sont utilisés et où

l'oxygène est administré.

• Gardez les enfants sous l'âge de 12 ans et les animaux loin de la moto à tout moment.

• Le vélo ne doit pas être utilisé par des personnes pesant plus de 300lbs (136 kg).

• Ne laissez jamais plus d'une personne sur le vélo à la fois. Porter des vêtements exercice approprié lors de

l'utilisation du vélo. Ne portez pas de vêtements amples qui pourraient se coincer dans le vélo. Les

vêtements de support sont recommandés pour les hommes et les femmes. Portez toujours des chaussures

de sport. Ne jamais utiliser le vélo avec les pieds nus, porter des bas seulement, ou en sandales..

• Lorsque vous branchez le cordon d'alimentation, branchez le cordon d'alimentation dans un circuit à la terre.

• Toujours examiner votre vélo avant de l'utiliser pour s'assurer que toutes les pièces sont en ordre de marche

.

• Laisser le vélo à venir à un arrêt complet avant ma descente.

• Ne jamais insérer d'objet ou le corps des pièces dans les ouvertures.

• Suivez les consignes de sécurité en ce qui concerne le branchement de votre vélo

• Gardez le cordon d'alimentation loin des roues pente et ne pas courir le cordon d'alimentation en dessous de

votre vélo. Ne pas faire fonctionner la moto avec un cordon d'alimentation endommagé ou effiloché.

• Débranchez toujours le vélo avant de le nettoyer et / ou d'entretien. Service pour votre moto ne doit être

effectuée par un représentant de service autorisé, sauf autorisation et / ou les instructions du fabricant. Le

non respect de ces instructions annule la garantie de vélo

4 V 390 SEMI-RECUMBENT BIKE

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This bike can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and noise

interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of bike

damage, always use a surge protector (not included) with your bike.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 120VAC, 15 amps.

This bike must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current,

should the bike malfunction. This bike is equipped with an electrical cord that has an equipment-grounding conductor and a

grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

www.smoothfitness.com

5

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists

on pages 7 for a full count of the parts included. If you are missing any parts or have any questions contact us

directly at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 300LBS (Approx. 136 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

6 V 390 SEMI-RECUMBENT BIKE

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

Console Upper Cover Console Bottom Cover Console Sleeve

Upright Post Assembly &

Water Bottle Bracket

Front Small Handlebar Upright Sleeve Seat Cushion

Mesh Backrest & Mesh

Backrest Cover

Rail Decoration Cover

Square Stopper,

Hex Head Bolt & Nut (M8)

Pedal Front Stabilizer

Seat Handlebar Assembly Seat Frame adjusting Handle Rear Stabilizer

Seat Carriage Assembly Main Frame Assembly & Leveler

Pull Bar & Fixed Bracket

for Seat Rail

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

NOTICE:

The length of all bolts and screws except those with flat heads is

Measured from below the head to the end of the bolt or screw. Flat head

bolts and screws are measured from the top of the head to the end of

the

bolt or screw

After unpacking the unit, you will notice that the package includes 3 bags of hardware (HARDWARE KIT A,

HARDWARE KIT B and HARDWARE KIT C).

Assembly’s Step 1: Using HARDWARE KIT A

Assembly’s Step 2, 4: Using HARDWARE KIT B

Assembly’s Step 7 ~ 9: Using HARDWARE KIT C

Note:

a. Please review below to know the content of each hardware kit (A, B and C)

b. Some small parts may have been pre-attached for shipping. If a part is not in the hardware bag, check to see if it has

been pre-assembled

HARDWARE KIT A

Part No. and Description

Q’TY

88 Lock Washer (M8)

4 pcs

90 Washer (8x16x2.0t)

4 pcs

115 Bolt, Socket Head (M8xp1.25x90mm)

4 pcs

HARDWARE KIT B

Part No. and Description

Q’TY

88 Lock Washer (M8)

5 pcs

90 Washer (8x16x2.0t)

5 pcs

97 Screw, Pan Head (M5xp0.8x25mm)

4 pcs

8 V 390 SEMI-RECUMBENT BIKE

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

HARDWARE KIT B

Part No. and Description

Q’TY

99 Screw, Round Head (M5xp0.8x15mm)

4 pcs

111 Bolt, Socket Head (M6xp1.0x15mm)

112 Bolt, Socket Head (M8xp1.25x16mm)

114 Bolt, Socket Head (M8xp1.25x55mm)

4 pcs

1 pcs

HARDWARE KIT C

Part No. and Description

Q’TY

88 Lock Washer (M8)

10 pcs

90 Washer (8x16x2.0t)

10 pcs

93 Self-Tapping Screw, Truss Head (M4x16mm)

1 pc

99 Screw, Round Head (M5xp0.8x15mm)

2 pcs

107 Carriage Bolt (M8xp1.25x50mm)

2 pcs

112 Bolt, Socket Head (M8xp1.25x16mm)

113 Bolt, Socket Head (M8xp1.25x40mm)

10 pcs

4 pcs

119 Bolt, Hex Head (M10xp1.5x90mm)

1 pc

127 Nylock Nut (M8)

128 Thin Nylock Nut (M10xp1.5)

2 pcs

1 pc

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:

MULTI WRENCH TOOL W/

PHILLIPS SCREWDRIVER

(13 & 15mm)

ALLEN WRENCH

(5 & 6 mm)

HEX WRENCH

(17mm x 2 pcs)

www.smoothfitness.com

9

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-1

Main Frame

1

V390-2

Front Seat Support Bracket

1

V390-3

Inner Seat Carriage Slider

1

V390-4

Outer Seat Carriage Slider

1

V390-5

Front Stabilizer

1

V390-6

Rear Stabilizer

1

V390-7

Upright Post

1

V390-8

Front Small Handlebar

1

V390-9

Seat Carriage

1

V390-10

Seat Fixed Stand

1

V390-11

Seat Frame

1

V390-12

Seat Handlebar

1

V390-13

Front Left Chain Cover

1

V390-14

Front Right Chain Cover

1

V390-15

Crank Cover (L&R)

2

V390-16

Rear Left Chain Cover

1

V390-17

Rear Right Chain Cover

1

V390-18

Decoration Cover for Carriage Slider

1

V390-19

Connection Cover

1

V390-20

Left Pedal

1

V390-21

Right Pedal

1

V390-22

Pulley

1

V390-23

Magnet

1

V390-24

Belt

1

V390-25

Pressure Wheel

1

V390-26

Bushing (

ψ

50.8x

ψ

10)

2

V390-27

Bushing (

ψ

60x

ψ

10)

4

V390-28

Slider Sleeve

1

V390-29

Pull Bar

1

V390-30

Tube Decoration Cover for Stabilizer

2

V390-31

Transprtation Wheel (L&R)

2

V390-32

Front Stabilizer End Cap

2

V390-33

Adjusting Rear Stabilizer End Cap

2

V390-34

Upright Sleeve

1

V390-35

Foam Grip (530mm)

2

V390-36

Square Plug (20x40mm)

1

V390-37

Console Upper Cover

1

10 V 390 SEMI-RECUMBENT BIKE

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-38

Console Bottom Cover

1

V390-39

Left Console Sleeve

1

V390-40

Right Console Sleeve

1

V390-41

Mesh Backrest

1

V390-42

Seat Cushion

1

V390-43

Foam Grip (330mm)

2

V390-44

Hand Pulse Sensor (L&R)

2

V390-45

Round Plug (31.8mm)

4

V390-46

Tube Plug (25.4mm)

4

V390-47

Locking Bar

1

V390-48

Left Seat Carriage Cover

1

V390-49

Right Seat Carriage Cover

1

V390-50

Adjusting Handle

1

V390-51

Seat Fixed Wheel

1

V390-52

Roller (37.6mm)

4

V390-53

Square Stopper

4

V390-54

Left Rail Decoration Cover

1

V390-55

Right Rail Decoration Cover

1

V390-56

Flywheel

1

V390-57

Cable

1

V390-58

Fixed Bracket for Motor

1

V390-59

Left Crank

1

V390-60

Right Crank

1

V390-61

Axle for Crank

1

V390-62

Fixed Bracket for Idler

1

V390-63

Upright Cover (L&R)

2

V390-64

Seat Rail

1

V390-65

Fixed Bracket for Seat Rail

1

V390-66

Adjusting Handle Stand

1

V390-68

Fixing Pin

1

V390-69

Axle for Sliding Track

1

V390-70

Axle for Braking

1

V390-71

Axle for Backrest Tube

1

V390-72

Bearing (6004zz)

2

V390-73

Eye Bolt (40mm)

2

V390-74

Eye Bolt (50mm)

3

V390-75

Tension Bracket

2

www.smoothfitness.com

11

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-76

Bushing (10.2x14x2mm)

1

V390-77

Bushing (10.2x14x10mm)

1

V390-78

Idler Spring

1

V390-79

Spring for Seat Fixed Stand

1

V390-80

Spring for Fixing Pin

1

V390-81

Spring for Adjusting Handle Stand

1

V390-82

Bushing for Seat Fixed Wheel

2

V390-83

Screw Cap

2

V390-84

Bushing (8x12x6.5mm)

4

V390-85

C Ring (20mm)

1

V390-86

Wave Washer

1

V390-88

Lock Washer (M8)

23

V390-89

Washer (6x19x1.5t)

2

V390-90

Washer (8x16x2.0t)

25

V390-91

Washer (10x23x2.0t)

3

V390-92

Washer (21x30x1.0t)

2

V390-93

Self-Tapping Screw, Truss Head (M4x16mm)

9

V390-94

Self-Tapping Screw, Truss Head (M5x18mm)

27

V390-95

Self-Tapping Screw, Flat Head (M4x20mm)

2

V390-96

Bolt, Button Head (M6xp1.0x40mm)

2

V390-97

Screw, Pan Head (M5xp0.8x25mm)

4

V390-98

Screw, Round Head (1/4’’x20mm)

4

V390-99

Nylon-Coated Screw, Round Head (M5xp0.8x15mm)

14

V390-100

Screw, Round Head (M5xp0.8x40mm)

2

V390-101

Bolt, Round Head (M6xp1.0x25mm)

8

V390-102

Bolt, Round Head (M6xp1.0x35mm)

2

V390-103

Bolt, Round Head (M6xp1.0x65mm)

1

V390-104

Screw, Flat Head (M5xp0.8x12mm)

4

V390-105

Bolt, Pan Head (M8xp1.25x15mm)

2

V390-106

Bolt, Pan Head (M8xp1.25x25mm)

4

V390-107

Carriage Bolt (M8xp1.25x50mm)

2

V390-108

Bolt, Button Head (M10xp1.25x35mm)

1

V390-109

Bolt, Hex Head (M10xp1.25x45mm)

1

V390-111

Bolt, Socket Head (M6xp1.0x15mm)

4

V390-112

Bolt, Socket Head (M8xp1.25x16mm)

14

V390-113

Bolt, Socket Head (M8xp1.25x40mm)

4

V390-114

Bolt, Socket Head (M8xp1.25x55mm)

1

12 V 390 SEMI-RECUMBENT BIKE

COMPLETE PARTS LIST

NO.

Item Name

Q'TY

V390-115

Bolt, Socket Head (M8xp1.25x90mm)

4

V390-116

Bolt, Hex Head (M8xp1.25x16mm)

4

V390-117

Bolt, Hex Head (M8xp1.25x105mm)

1

V390-118

Bolt, Hex Head (M8xp1.25x115mm)

2

V390-119

Bolt, Hex Head (M10xp1.5x90mm)

1

V390-120

Bolt, Hex Head (M10xp1.5x115mm)

2

V390-121

Collar Screw (M6)

2

V390-122

Flange Nut (M10)

2

V390-123

Nut (M6)

3

V390-124

Nut (M8)

4

V390-125

Nylock Nut (M6)

6

V390-126

Thin Nylock Nut (M8)

8

V390-127

Nylock Nut (M8)

9

V390-128

Thin Nylock Nut (M10xp1.5)

3

V390-129

Nylock Nut (M10xp1.25)

2

V390-130

Front Connection Wire

1

V390-131

Rear Connection Wire

1

V390-132

Adaptor Connection Wire w/ Nut

1

V390-133

Adaptor

1

V390-134

Sensor Wire w/Stand

1

V390-135

Motor w/ Wire

1

V390-136

Pulse Sensor Wire 1

1

V390-137

Pulse Sensor Wire 2

1

V390-138

Pulse Sensor Wire 3

1

V390-139

Short Extension Pulse Wire

1

V390-140

Pulse Sensor Wire 4

1

V390-141

Square Plug (25x75mm)

1

V390-142

Flange Nut – Black Color (M10)

2

V390-143

Nut (M5)

1

V390-144

Bolt, Button Head (M8xp1.25x16mm)

4

V390-145

Washer (8x26x2.0t)

2

V390-146

Self-Tapping Screw, Button Head (M4x16mm)

4

V390-147

Leveler

1

V390-148

Mesh Backrest Cover

1

V390-149

Lock Washer (M6)

4

V390-150

Water Bottle Bracket

1

V390-151

Bolt, Round Head M5x12mm

2

www.smoothfitness.com

13

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

14 V 390 SEMI-RECUMBENT BIKE

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.

www.smoothfitness.com

15

PARTS DISCRIPTION

Console

Front Small Handlebar

Mesh Backrest

Console Sleeve

Pulse

Sensor

Upright Post

Upright Sleeve

Adjusting

Handle

Main Frame

Front Stabilizer

Pedal

Seat Carriage

Assembly

Pull Pin

Rear Stabilizer

Water Bottle

Bracket

16 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

Step 1: Attach the Stabilizers, Leveler and Pedals

Note: the stabilizer is marked with an R to denote the right side.

Caution: Improperly rotating the pedal threads may cause damage to the equipment

A).Attach the front stabilizer to the main frame using 2x M8xp1.25x90mm Socket Head Bolts (115), 2 x M8 Lock

Washers (88) and 2 x 8x16x2.0t Washers (90). Slide the bolts through the front stabilizer and tread them in to the main

frame.

B). Attach the rear stabilizer to the main frame using 2x M8xp1.25x90mm Socket Head Bolts (115), 2 x M8 Lock

Washers (88) and 2 x 8x16x2.0t Washers (90). Slide the bolts through the rear stabilizer and tread them in to the main

frame.

C) Tilt the bike to the side and thread the leveler completely into the frame. You will adjust the leveler after assembly is

complete

D). Attach the right pedal into the right side crank. To tighten, turn the pedal treads clockwise.

E). Attach the left pedal to the left side crank. To tighten, turn the pedal threads counter clockwise

Be sure to thread the Leveler (147)

tightly into the Main Frame (1) before

moving to the next page

Tighten all bolts and fasteners now

USE HARDWARE KIT

A

www.smoothfitness.com

17

ASSEMBLY

STEP 2: Attach the Upright Post Assembly

Note: Do not tighten the upright post bolts until all four bolts are threaded into the post.

Caution: Do not pinch the wires between the frame

A). Slid the upright sleeve (34) on to the upright post assembly.

B). Attach the upright post assembly to the main frame using 4 x M8xp1.25x16mm socket head bolts (112), 4 x M8 lock

washers (88) and 4 x 8x16x2.0t washers(90).

C). Connect the Pulse Sensor Wire 3 (138) to the Pulse Sensor Wire 2 (137).

D). Connect the Rear Connection Wire (131C) to the Motor Wire (135).

E). Connect the Rear Connection Wire (131B) to the Sensor Wire (134).

F). Connect the Rear Connection Wire (131A) to the Adaptor Connection Wire (132).

G) Slide the upright post sleeve down until it attaches to the main frame covers.

Tighten all bolts and fasteners now

USE HARDWARE KIT

B

18 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 3: Attach the Console and Front Handlebar

Make sure all wires are recessed into the frame. DO NOT trap or pinch the wires.

A). Attach the console bottom cover (38) to the console upper cover (37) and secure using 4 x M5xp0.8x25mm pan

head screws (97). See Fig.1

B). Remove the 4 x bolts and washers from the front handlebar.

C). Slide the front handlebar through the upright post bracket. Secure the handlebar using 5 x M8xp1.25x16mm button

head bolts (114), 5 x M8 (88) and 5 x 8x16x2.0t washers (90) Tighten all bolts now,

NOTE: One Washer (8x16x2.0t)(90), one Lock Washer (M8)(88), one Bolt, Socket Head (M8xp1.25x45mm)(114) will

be packed into the hardware bag.

Tighten all bolts and fasteners now

www.smoothfitness.com

19

ASSEMBLY

STEP 4: Attach the Console Sleeve Assembly and Water Bottle bracket

A). Slide the console sleeve assembly (39) (40) around the upright post.

B) Be certain that the sleeve assembly aligns together properly and the lowest portion of the console bottom cover is

inside the console sleeve assembly.

C). Secure the two sleeves together using 4 x M5xp0.8x15mm round head screws (99)

D). Remove the pre-installed water bottle bracket screws from the console post

E). Line up the water bottle bracket with the upright post as pictured below.

F). Secure the bracket using the previously removed 2 x M5x12mm (151) round head bolts

USE HARDWARE KIT

B

Tuck the lowest

portion of the console

bottom cover under

the sleeve assembly’s

lip

Tighten all bolts and fasteners now

20 V 390 SEMI-RECUMBENT BIKE

ASSEMBLY

STEP 5: Attach the Inner Seat Carriage Slider

A). Insert the inner seat carriage slider (3) Into the main frame.

B) Slide the slider up to #5 and insert the pull pin in to the hole making sure the pan passes through the main frame

into the seat slider carriage.

C). Tighten the pull pin clockwise as much as possible.

La page charge ...

Smooth Fitness V390 Manuel utilisateur

Smooth Fitness V390 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents