Blaupunkt monte carlo mp 34 Manuel utilisateur

Radio / CD

http://www.blaupunkt.com

Radio / CD / MP3

Monte Carlo MP34 7 643 193 510

Bahamas MP34 7 643 194 510

Operating and installation instructions

Notice d’emploi et de montage

Instrucciones de manejo e instalación

Instruções de serviço e de montagem

http://www.blaupunkt.com

2

Open here

Ouvrir s.v.p.

Por favor, abrir

Favor abrir

Bahamas MP34_2-3_E/F/S/P 13/11/03, 10:402

3

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

11

1

33

3

22

2

55

5

66

6

::

:

77

7

88

8

99

9

44

4

;;

;

Bahamas MP34_2-3_E/F/S/P 13/11/03, 10:403

4

CONTROLS

1 button to open and release

the control panel.

2 Button to switch the unit on/off

and to mute the unit.

3 Volume control.

4 Short press: BND button, to

select the FM memory bank

and the AM waveband, source

selection to radio mode.

Long press: TS, to start the

Travelstore function.

5 AUDIO button, to adjust the

bass, treble, balance and fader

settings, X-Bass, Sound Preset

EQ.

6 Short press:

button, to display

the time.

Long press: to change the

display priority.

7 Arrow buttons

8 Short press: MENU button, to

open the basic settings menu.

Long press: SCAN, to start scan

function.

9 Keys 1 - 6

: SRC button, to select the CD/

MP3, radio and CD changer

(AUX) sources.

; Eject button 0 (which can only

be seen after flipping the control

panel).

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:594

5

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

TABLE OF CONTENTS

Road safety ..................................... 6

Installation ....................................... 6

Accessories .................................... 6

International telephone information ... 6

Removable control panel ......... 7

Theft protection ............................... 7

Detaching the control panel ............. 7

Attaching the control panel .............. 7

Off timer .......................................... 8

Switching on/off ...................... 8

Adjusting the volume ............... 9

Setting the power-on volume ........... 9

Instantaneous volume reduction

(mute) ........................................... 10

Mute while telephoning .................. 10

Confirmation beep ......................... 10

Radio mode ............................ 11

Switching to radio mode ................ 11

Setting the tuner ............................ 11

Selecting the frequency range/

memory ......................................... 11

Tuning into a station ....................... 11

Storing stations ............................. 12

Storing stations automatically

(Travelstore) .................................. 12

Listening to preset stations ............ 12

Scanning receivable stations

(SCAN) ......................................... 12

Setting the display ......................... 13

CD mode ................................ 13

Switching to CD mode .................. 13

Selecting tracks ............................ 14

Fast searching (audible) ................ 14

Random play (MIX) ........................ 14

Scanning tracks (SCAN) ............... 14

Repeating tracks (REPEAT) ........... 14

Pausing playback (PAUSE) ............ 15

Changing the display ..................... 15

Displaying CD text ......................... 15

Ejecting a CD ................................ 15

MP3 Mode .............................. 16

Preparing the MP3-CD .................. 16

Switching to MP3 mode ................ 17

Selecting a directory...................... 17

Selecting tracks/files ..................... 17

Fast searching............................... 17

Random track/file play (MIX) .......... 17

Scanning tracks/files (SCAN) ........ 18

Repeating individual tracks/files or

whole directories (REPEAT)........... 18

Pausing playback (PAUSE) ............ 18

Setting the display ......................... 18

CD changer mode .................. 19

Switching to CD changer mode ..... 19

Selecting a CD .............................. 19

Selecting tracks ............................ 19

Fast searching (audible) ................ 19

Changing the display ..................... 20

Repeating individual tracks or

whole CDs (REPEAT).................... 20

Random play (MIX) ........................ 20

Scanning all tracks on all CDs

(SCAN) ......................................... 20

Pausing playback (PAUSE) ............ 20

CLOCK - Time ........................ 21

Briefly displaying the time .............. 21

Setting the time ............................. 21

Selecting 12/24-hour clock mode .. 21

Displaying the time continuously

when the unit is off and the ignition

is on .............................................. 21

Briefly displaying the time when

the unit is switched off ................... 21

Tone and volume

distribution settings ............... 22

Adjusting the bass settings ............ 22

Adjusting the treble settings........... 22

Setting the left/right volume

distribution (balance) ..................... 22

Setting the front/back volume

distribution (fader) ......................... 22

Equalizer and X-BASS ........... 23

X-BASS ........................................ 23

Selecting preset sound effect (EQ) .. 23

Setting the level display ......... 24

External audio sources .......... 24

Switching the AUX input on/off ...... 24

Specifications ........................ 25

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:595

6

Thank you for deciding to purchase a

Blaupunkt product. We hope you enjoy

using this new piece of equipment.

Before using the device for the first time,

please read these instructions carefully.

The Blaupunkt editors are constantly

working on making the operating

instructions clearer and easier to

understand. However, if you still have

any questions on how to operate the unit

please contact your dealer or the

telephone hotline for your country. You

will find the hotline telephone numbers

printed at the back of this booklet.

Road safety

Road safety has absolute

priority. Only operate your car radio

if the road and traffic conditions allow

you to do so. Familiarise yourself with

the unit before setting off on your

journey.

You should always be able to hear

police, fire and ambulance sirens

from afar. For this reason, set the

volume of whatever you are listening

to to a reasonable level.

Installation

If you want to install your car radio

yourself, please read the installation and

connection instructions that follow these

operating instructions.

Accessories

Only use accessories approved by

Blaupunkt.

NOTES AND ACCESSORIES

Remote control

RC-12H is included. You can

conveniently access the most important

functions of your car radio from the

steering wheel via the optional RC08 or

RC10.

Amplifier

All Blaupunkt and Velocity amplifiers can

be used.

CD changer

You can connect the following Blaupunkt

CD changers: CDC A 08, IDC A 09 and

CDC A03.

Compact Drive MP3

As an alternative to a CD changer, you

can connect a Compact Drive MP3 to

access MP3 music tracks. If you con-

nect a Compact Drive MP3, you will first

need to use a computer to store the MP3

music tracks on the Microdrive™ hard

disk inside the Compact Drive MP3.

Then, when the Compact Drive MP3 is

connected to the car radio, you can play

the tracks like normal CD music tracks.

The Compact Drive MP3 is operated in

the same way as a CD changer. Most

of the CD changer functions can also

be used with the Compact Drive MP3.

International telephone

information

If you have any questions regarding the

operation of your car radio or if you

require further information, please do

not hesitate to call us!

The information hotline numbers are

printed on the last page of these

instructions.

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:596

7

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Removable control panel

Theft protection

As a way of protecting your equipment

against theft, the unit is equipped with

a detachable control panel (release

panel). Without this control panel, the

car radio is worthless to a thief.

Protect your equipment against theft by

taking the control panel with you every

time you leave your vehicle. Do not

leave the control panel in your vehicle -

not even in a hidden place.

The control panel has been designed

to be easily use.

Note:

● Never drop the control panel.

● Never expose the control panel to

direct sunlight or other heat

sources.

● Avoid making direct skin contact

with the control panel’s contacts. If

necessary, clean the contacts with

a lint-free cloth and some alcohol.

Detaching the control panel

➮ Press the button 1.

The control panel locking mechanism

opens.

➮ Pull the control panel straight off

the unit, by holding the right hand

side of the control panel.

Notes:

● The unit may only switch off after a

few seconds, depending upon the

“OFF TIMER” setting in the MENU

as described later.

● All current settings of the radio are

saved.

● CD already inserted in the unit

remains there.

Attaching the control panel

There are various ways of attaching the

control panel but the following method

is recommended:

➮ Hold the control panel

perpendicular to the unit.

➮ Slide the control panel into the

unit’s guides, located at the lower

left and right sides, until it clicks

into place.

➮ Push the control panel gently in

upward direction until it clicks into

its place.

Note:

● When attaching the control panel,

make sure you do not press on the

display.

If the unit was still switched on when

you removed the control panel, the unit

will automatically switch back on with

the last settings activated i.e. radio, CD

(MP3) or CD changer (AUX) when the

panel is reinserted.

REMOVABLE CONTROL PANEL

1

2

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:597

8

Switching on/off

There are various ways of switching the

unit on/off:

Switching on/off using the vehicle

ignition

If the unit is correctly connected to the

vehicle’s ignition and it was not switched

off using ON/OFF button 2, it will

switch on/off simultaneously with the

ignition.

Switching on/off using the

removable control panel

➮ Remove the control panel.

The unit switches off. A delay in

switching off is expected if the “OFF

TIMER” setting is not “0”.

➮ Attach the control panel again.

The unit switches on. The last settings

(radio, CD/MP3, CD changer or AUX)

will be reactivated.

Switching on/off using button 2

➮ To switch the unit on, press button

2.

➮ To switch the unit off, press button

2 for longer than two seconds.

The unit switches off.

Note:

● If you switch on the unit when the

ignition is off, the unit will switch off

automatically after one hour to

prevent draining of the vehicle

battery.

Off timer

After opening the control panel, the unit

will switch off after a pre-adjusted time

between 0 to 30 seconds.

➮ Press the MENU button 8.

➮ Press the ﬁ button 7 twice to

display “OFF TIMER”.

➮ Set the time using the @ or #

buttons 7.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

Note:

● If the OFF TIMER is set to 0

second, the unit switches off

immediately after opening the

control panel.

SWITCHING ON/OFF

REMOVABLE CONTROL PANEL

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:598

9

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Switching on by inserting a CD

If the unit is switched off and there is no

CD inserted in the drive,

➮ press the button 1.

The release panel opens.

➮ Gently insert the CD with the

printed side uppermost into the

drive until you feel some

resistance.

The CD will be drawn automatically into

the drive.

You must not hinder or assist the drive

as it draws in the CD.

➮ Gently close the control panel

whilst exerting a little pressure until

you feel it clicks into place.

The unit switches on. CD playback

begins.

Note:

● The unit will remain off if the

ignition is off. To turn it on, press

button 2 once.

Adjusting the volume

The volume can be adjusted in steps

from 0 (mute) to 66 (maximum).

➮ To increase the volume, turn the

volume control 3 to the right.

➮ To decrease the volume, turn the

volume control 3 to the left.

Setting the power-on volume

You can set the unit’s default power-on

volume.

➮ Press the MENU button 8.

➮ Keep pressing the ﬁ or % button

7 until “ON VOLUME” appears in

the display.

➮ Set the power-on volume using the

@ and # buttons 7.

To help you adjusting the volume more

easily, the audible volume level will

increase or decrease accordingly as you

make your changes.

If you select “LAST VOL”, the volume

played before the unit was last switched

off will be reactivated.

Note:

● To protect your hearing, the

maximum switch-on volume under

the “LAST VOL” setting is “38”. If

the volume was higher before the

unit was switched off and “LAST

VOL” has been selected, the

volume will be set at “38” the next

time the radio is switched on.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

ADJUSTING THE VOLUMESWITCHING ON/OFF

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:599

10

Instantaneous volume reduction

(mute)

This feature allows you to

instantaneously reduce (mute) the

volume to a level preset by you.

➮ Briefly press button 2.

“MUTE” appears in the display.

To restore the volume,

➮ press button 2 again.

Setting the mute level

You can set the unit’s mute volume level.

➮ Press the MENU button 8.

➮ Keep pressing the ﬁ or % button

7 until “MUTE LVL” appears in

the display.

➮ Set the mute level using the @ and

# buttons 7.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

Mute while telephoning

If your unit is connected to a mobile

telephone, the car radio’s volume will

be muted as soon as you “pick up” the

telephone. “PHONE” shows in the

display.

This requires the mobile telephone be

connected to the car radio as

described in the installation

instructions.

Confirmation beep

For some functions you will hear a

confirmation beep if you keep a button

pressed for longer than two seconds.

For instance, after storing a radio station

to a station button you will hear a

confirmation beep. The beep can be

switched on/off.

➮ Press the MENU button 8.

➮ Keep pressing the % or ﬁ button

7 until “BEEP” appears in the

display.

➮ Use the @ and # buttons 7 to

switch between the options.

“OFF” means beep off, “ON” means the

beep is switched on.

➮ Press the MENU button 8.

ADJUSTING THE VOLUME

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5910

11

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Radio mode

Switching to radio mode

If you are listening to CD/MP3, CD

changer or AUX mode,

➮ press the BND-TS 4 button

or

➮ keep pressing the SRC button :

until “FM” or “AM” (“MW”) appears

in the display.

Setting the tuner

In order to guarantee the perfect func-

tioning of the radio element, the unit

must be set for the region in which you

are located. You can choose between

Europe (EUROPE), America (USA),

Thailand (THAI) and South America

(S-AMERICA). The tuner comes from

the factory set for the region in which

the unit was sold. Should you encounter

problems with radio reception, please

check this setting.

This set of instructions refers to the

“USA” setting.

➮ Press the MENU button 8.

➮ Press the ﬁ button 7 repeatedly

until “TUNER” appears on the

display.

➮ Keep pressing the @ or

# button

7 until the desired region appears

in the display.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

Selecting the frequency range/

memory

This unit can receive programmes

broadcast over the FM and AM

frequency ranges. There are three

preset memory levels for the FM range

and one for the AM range. Six stations

can be stored on each memory level.

Selecting the FM memory level or

the AM frequency range

respectively

➮ Keep pressing the BND-TS button

4 to switch between the FM

memory levels (FM1, FM2 and

FMT) and the AM frequency range

respectively.

Tuning into a station

There are various ways of tuning into a

station.

Automatic seek tuning

➮ Press the ﬁ or % button 7.

The unit tunes into the next receivable

station.

Setting the sensitivity for station

seek tuning

You can configure the radio to only tune

into stations with a strong reception or

to also tune into those with a weak

reception.

➮ Press the MENU button 8.

➮ Keep pressing the ﬁ or % button

7 until “SENS HI” or “SENS LO”

appears in the display.

RADIO MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5911

12

“SENS HI” means that the tuner is highly

sensitive. “SENS LO” means it is set to

the lower sensitivity setting.

➮ Set the required sensitivity using

the @ or # buttons 7.

When you have finished making your

changes,

➮ press the MENU button 8.

Note:

● Different seek tuning sensitivities

can be set separately for FM and

AM respectively.

Tuning into stations manually

You can also tune into stations manually.

➮ Press the @ or # button :.

Storing stations

Storing stations manually

➮ Select the required memory level

(FM1, FM2 or FMT) or the AM

frequency range.

➮ Tune into the station.

➮ Press one of the station buttons

1 - 6 9 for longer than 2 seconds

to store the station to that button.

Storing stations automatically

(Travelstore)

You can automatically store six stations

with the strongest reception in the

region. The stations are stored in the

FMT or AM memory depending on the

selected frequency range.

Note:

● Stations that were previously

stored in this memory are deleted

in the process.

➮ Press and hold the BND-TS button

4 until the seek tuning starts.

The station storing procedure begins.

“FM TSTORE” or “AM TSTORE”

appears in the display. After the process

is completed, the station that is stored

in location 1 of the respective memory

level will be played.

Listening to preset stations

➮ Select the memory level on which

the station was stored.

➮ Press the preset station button

1 - 6 9 of the station you want to

listen to.

Scanning receivable stations

(SCAN)

You can briefly play all the receivable

stations by activating the scan function.

You can set the scanning time to

between 5 and 30 seconds in the menu.

Starting SCAN

➮ Keep the MENU button 8 pressed

until the scan process starts.

“SCAN” appears briefly in the display

followed by the current frequency (which

flashes).

Stopping SCAN and continuing

listening to a station

➮ Press the MENU button 8.

Scanning is stopped and the station that

was tuned into last will remain active.

RADIO MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5912

13

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

CD mode

You can use this unit to play standard

CDs, CD-Rs and CD-RWs with a

diameter of either 5 or 3 inches.

Beside playing CDs containing audio

data, CDs containing MP3 files can also

be played on this device.

Descriptions of the “MP3 mode” can be

found after this chapter.

Risk of damage to the CD

drive! Contoured CDs (shape CDs)

are not suitable for playback in this

unit.

We accept no liability for any damage

to the CD drive or CD that may occur

as a result of the use of unsuitable

CDs.

Switching to CD mode

● If there is no CD inserted in the

drive and the unit is playing Radio

or CD Changer (AUX) mode,

➮ press the button 1.

The release panel opens.

➮ Gently insert CD with the printed

side uppermost into the drive until

you feel some resistance.

The CD is drawn into the drive

automatically.

You must not hinder or assist the drive

as it draws in the CD.

➮ Gently close the control panel

whilst exerting a little pressure until

you feel it clicks into place.

CD playback begins.

Setting the scantime

➮ Press the MENU button 8.

➮ Keep pressing the ﬁ or % button

7 until “SCAN TIME” appears in

the display.

➮ Set the required scantime using

the @ or # buttons 7.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

Note:

● The set scantime also applies to

scanning in CD/MP3 and CD

changer mode.

Setting the display

You can choose to continuous display

one of the followings:

● Time

● Frequency

➮ Keep the button 6 pressed

until the required display appears.

CD MODERADIO MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5913

14

Note:

The unit will remain off if the ignition is

off. To turn it on and play

the inserted

CD, press buton 2 once.

● If a CD is already inserted in the

drive and the unit is playing Radio

or CD Changer (AUX) mode.

➮ Keep pressing the SRC button :

until “CD” appears in the display.

Playback begins from the point at which

it was last interrupted.

Selecting tracks

➮ Press one of the arrow buttons 7

to select the next or previous track.

If you press the ﬁ or @ button 7 once,

the current track will be played again

from the beginning.

Fast searching (audible)

To fast search backwards or forwards,

➮ keep one of the @ # buttons 7

pressed until fast reversing / fast

forwarding begins.

Random play (MIX)

➮ Press button 5 MIX 9.

“MIX CD” appears briefly in the display

and the MIX symbol lights up. The next

randomly selected track will then be

played.

Stopping MIX

➮ Press button 5 MIX 9 again.

“MIX OFF” appears briefly in the display

and the MIX symbol disappears.

Scanning tracks (SCAN)

You can briefly play all the tracks on a

CD.

➮ Press the MENU button 8 for

longer than two seconds. The next

track will then be played for

scantime as set in the “Setting the

scantime”.

Note:

● You can set the scantime. For fur-

ther details, please read the sec-

tion entitled “Setting the scantime”

in the “Radio mode” chapter.

Stopping SCAN and continuing

playback

➮ To stop scanning, press the MENU

button 8.

The current track will then continue to

be played.

Repeating tracks (REPEAT)

➮ If you want to repeat a track, press

button 4 RPT 9.

“RPT TRCK” appears briefly in the

display and the RPT symbol lights up.

The track is repeated until you

deactivate RPT.

Cancelling repeat

➮ If you want to stop the repeat

function, press button 4 RPT 9

again.

“RPT OFF” appears briefly in the display

and the RPT symbol disappears.

Normal playback is then continued.

CD MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5914

15

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Pausing playback (PAUSE)

➮ Press button 3 E 9.

“PAUSE” appears in the display.

Cancelling pause

➮ Press button 3 E 9 while in

pause mode.

Playback is continued.

Changing the display

Two options are available:

● Track number and clock.

● Track number and playing time.

➮ Press the button 6 for longer

than two seconds until the required

display appears.

Displaying CD text

Some CDs feature so-called CD text.

The CD text may include the name of

the performer, the album and the track

name.

You can have the CD text displayed as

running text at every change of track.

After the CD text has been displayed

once, the standard display (as

described in the “Changing the display”

section) will be shown.

Switching CD text on/off

➮ Press the MENU button 8.

➮ Press the ﬁ or % button 7

repeatedly until “CD TEXT”

appears on the display.

➮ Switch on (“TEXT ON”) or off

(“TEXT OFF”) the CD text function

by pressing the # or @ button 7.

When you have finished making your

changes,

➮ press the MENU button 8 twice.

Ejecting a CD

➮ Press the button 1.

The flip-release panel opens.

➮ Press the 0 button ; located beside

the CD insertion slot.

➮ Remove the CD and close the

control panel.

Notes:

● An ejected CD will be reloaded into

the unit if not removed within 10

seconds to protect it from

accidental damage.

● You may also eject a CD when the

unit is off, or when CD is not playing.

CD MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5915

16

MP3 mode

You can also use this car radio for

playing CD-Rs and CD-RWs containing

MP3 music files.

MP3 is a process developed by the

Fraunhofer Institute for compressing CD

audio data. Compression allows data to

be reduced to around 10% of their

original size without a noticeable loss

in quality (at a bit rate of 128 kbit/s). If a

lower bit rate is used to convert CD

audio data to MP3, you can create

smaller files but there will be a loss in

quality.

Preparing the MP3-CD

The various combinations of CD

burners, CD burning software and CD

blanks may lead to problems arising with

the ability to play certain CDs. If

problems occur with your own burned

CDs, you should try another brand of

CD blank or choose another blank

colour.

The format of the CD must be ISO 9660

Level 1 / Level 2 or Joliet. Other formats

cannot be played reliably.

You can create a maximum of 253

directories on a CD. Each of these

directories can be accessed using this

device.

Regardless of the number of directories

on a CD, a total of 65535 files can be

supported, even in one single directory.

This device can support as many

directory-nesting levels as your writing

software allows, even though the

maximum nesting level is standardized

as 8 levels in ISO9660.

Each directory can be named using a

PC. The directory name can be

displayed in the device’s display. Name

the directories and files using your CD

burner software. The software’s

operating instructions will provide details

on how to do this.

Note:

● When naming directories and files

you should avoid using special

characters. Use a maximum of 32

characters for file names (including

the extension “.MP3”) and directory

names.

If you like your files to be in the correct

order, you should use burner software

that places files in alphanumerical order.

If your software does not provide this

feature, you can also sort the files

manually. To do so, you should place a

MP3 MODE

Directories

Tracks/files

D01

D02

T001

T005

T004

T003

T002

D03

T001

T006

T005

T004

T003

T002

T011

T007

T008

T009

T010

D04

T001

T006

T005

T004

T003

T002

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5916

17

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

number (e.g. “001”, “002”, etc.) in front

of each file name - the leading zeros

must also be included.

MP3 tracks can contain addition infor-

mation such as the artist, song and

album names (ID3 tags). This device

can display ID3 tags if they are version 1.

When creating (encoding) MP3 files

from audio files, you should use bit rates

up to a maximum of 256 kbit/sec.

Only MP3 files with the “.MP3” file

extension can be played on this device.

Note:

To ensure uninterrupted playback,

● do not attempt to change the file

extension to “.MP3” of any files

other than MP3 files and then

attempt to play them! These invalid

MP3 files will not be selected

during MP3 playback.

● Do not use “mixed” CDs containing

both non-MP3 data and MP3 files.

The unit will only select MP3 files

during playback.

● Do not use mix-mode CDs

containing both audio tracks and

MP3 files. While attempting to

playback such CDs, only audio

tracks will be selected.

Switching to MP3 mode

MP3 mode is activated in the same way

as normal CD mode. For further details,

please read the “Switching to CD mode”

section in the “CD mode” chapter.

Selecting a directory

To move up or down to another

directory,

➮ press the ﬁ or % button 7 once or

several times.

Note:

● Any directories not containing MP3

files will be skipped automatically.

The total number of directories will

be readjusted by the unit, and may

not be the same as the number of

directories you have created.

Selecting tracks/files

To move up or down to another track/

file in the current directory,

➮ press the @ or # button 7 once

or several times.

If you press the @ button 7 once, the

current track/file will be played again

from the beginning.

Fast searching

To fast search backwards or forwards,

➮ keep one of the @ or # button 7

pressed until fast searching

backwards/forwards begins.

Random track/file play (MIX)

To play the tracks/files in the current di-

rectory in random order,

➮ briefly press button 5 MIX 9.

“MIX DIR” appears in the display and

the MIX symbol lights up.

MP3 MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5917

18

To play all the tracks/files on the inserted

MP3-CD in random order,

➮ press button 5 MIX 9 longer than

2 seconds.

“MIX CD” appears in the display and the

MIX symbol lights up.

Cancelling MIX

To cancel MIX,

➮ briefly press button 5 MIX 9.

“MIX OFF” appears in the display and

the MIX symbol disappears.

Scanning tracks/files (SCAN)

You can briefly play all the tracks/files

on the CD.

➮ Press the MENU button 8 for

longer than 2 seconds.

“SCAN” appears alongside the blinking

track/file numbers during the scanning

process.

Note:

● You can set the scanning time

(scantime). For further details on

setting the scantime, please read the

“Setting the scantime” section in the

“Radio mode” chapter.

Stopping SCAN and continuing

playback

➮ Briefly press the MENU button 8.

The currently scanned track/file will then

continue to be played normally.

Repeating individual track/file or

whole directories (REPEAT)

To play the current track/file repeatedly,

➮ briefly press button 4 RPT 9.

“RPT TRCK” appears briefly in the

display and RPT lights up.

To repeat the whole directory,

➮ press button 4 RPT 9 longer than

2 seconds.

“RPT DIR” appears briefly in the

display.

Cancelling REPEAT

To stop the current track or current

directory from being repeated,

➮ briefly press button 4 RPT 9.

“RPT OFF” appears briefly in the

display and the RPT symbol

disappears.

Pausing playback (PAUSE)

➮ Press button 3 E 9.

“PAUSE” appears in the display.

Cancelling pause

➮ Press button 3 E 9 while in

pause mode.

Playback is resumed.

Setting the display

Setting the standard display mode

While playing MP3 tracks/files, you can

choose to display one of the following

standard display modes:

● Track/file number and playing time

● Track/file number and clock time

● Directoy number and track/file

number

● Directoy number and clock time

● Directoy number and playing time

MP3 MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5918

19

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

The chosen display will be shown after

scrolling the MP3 texts at every change

of track/file.

To set the displays,

➮ press the button 6 repeatedly

for longer than two seconds until

the desired mode is shown.

Setting the MP3 scrolling texts

You can configure the display to scroll

one of the following options at every

change of MP3 track/file. After the

scrolling texts have been displayed

once, the standard display (as

described earlier) will be shown. The

available options are:

● Directory name

● File name

● Artist name

● Song name

● Album name

Note:

● Artist, song and album names are

part of the ID3 tag version 1 and

will not be shown if they are not

available on the MP3 files.

To configure the MP3 scrolling texts,

➮ Press the MENU button 8.

➮ Press % or ﬁ button 7 repeatedly

until “MP3 DISP” appears on the

display.

➮ Select the preferred option via the

@ or # button 7.

➮ Press the MENU button 8 twice

to complete the setting.

CD CHANGER MODE

CD changer mode

Note:

● Information on handling CDs,

inserting CDs and operating the

CD changer can be found in the

operating instructions supplied with

your CD changer.

Switching to CD changer mode

➮ Keep pressing the SRC button :

until “CHANGER” appears in the

display.

The CD Changer will resume playback

from where it was last played previously.

Selecting a CD

➮ To move up/ down from one CD to

another, press the % or ﬁ button

7 once or several times.

➮ An empty CD magazine slot will be

skipped in the CD selection

process.

Selecting tracks

➮ To move up/ down from one track

to another on the current CD, press

the # or @ button 7 once or

several times.

Fast searching (audible)

To fast search backwards or forwards,

➮ keep one of the @ # buttons 7

pressed until fast reversing/fast

forwarding begins.

MP3 MODE

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5919

20

Changing the display

5 options are available:

● Track number and play time

● Track number and clock

● CD number and track number

● CD number and clock

● CD number and play time

➮ Press the button 6 once or

several times for longer than two

seconds until the required display

appears.

Repeating individual tracks or

whole CDs (REPEAT)

➮ If you wish to repeat the current track,

briefly press button 4 RPT 9.

“RPT TRCK” appears briefly and RPT

lights up in the display.

➮ If you wish to repeat the current

CD, press button 4 RPT 9 longer

than two seconds.

“RPT DISC” appears briefly and RPT

lights up in the display.

Cancelling repeat

➮ If you want to stop the repeat

function for the current track or CD,

press button 4 RPT 9 briefly and

“RPT OFF” appears briefly in the

display and RPT disappears.

Random play (MIX)

➮ To play all the tracks on the current

CD in random order, briefly press

button 5 MIX 9.

“MIX CD” appears briefly and MIX lights

up in the display.

➮ To play the tracks on all the

inserted CDs in random order,

CD CHANGER MODE

press button 5 MIX 9 longer than

two seconds.

“MIX ALL” appears briefly and MIX lights

up in the display.

Stopping MIX

➮ Press button 5 MIX 9 briefly and

“MIX OFF” appears briefly in the

display and MIX disappears.

Scanning all tracks on all CDs

(SCAN)

➮ To briefly play all the tracks on all

inserted CDs in ascending order,

press the MENU button 8 for

longer than two seconds.

“TRK SCAN” appears briefly follows by

blinking the track number of the CD

track being scanned.

Stopping SCAN

➮ To stop scanning, briefly press the

MENU button 8.

The current track will then continue to

be played.

Note:

● You can set the scantime. For

further details, please read the

section entitled “Setting the

scantime” in the “Radio mode”

chapter.

Pausing playback (PAUSE)

➮ Press button 3

EE

E 9.

“PAUSE” appears in the display.

Cancelling pause

➮ Press button 3

EE

E 9 while in

pause mode.

Playback is continued.

BA Bahamas/Monte Carlo MP34_EN 13/11/03, 8:5920

La page charge ...

Blaupunkt monte carlo mp 34 Manuel utilisateur

Blaupunkt monte carlo mp 34 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents