Blaupunkt LAGUNA CD36 Le manuel du propriétaire

Radio CD

http://www.blaupunkt.com

Laguna CD36 7 646 085 510

Operating and installation instructions

Notice d’emploi et de montage

Instrucciones de manejo e instalación

Instruções de serviço e de montagem

ጇѰ̅Њཆ̙͋

사용 및 장착 설명서사용 및 장착 설명서

BA_LagunaCD36_cover.indd 1BA_LagunaCD36_cover.indd 1 3/14/06 9:53:44 PM3/14/06 9:53:44 PM

2

3

4

51

2

6

7

13

12

10

9

8

11

1BA_LaguCD36_gb 3/14/06, 2:25 PM2

3

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

1 Button to switch the unit on/off

and to mute the unit.

2 Button to release the control

panel.

3 CD Eject button

.

4 Volume control.

5 CD-Slot.

6 AUDIO button, to adjust the

bass, treble, balance and fader

settings and Sound Preset

7 Short press: MENU button, to

open the basic settings menu.

Long press: SCAN, to start scan

function.

8 Arrow buttons

9 X-Bass button to adjust the X-

Bass function.

: Short press:

DIS button, to

display the time.

Long press: to change the dis-

play priority.

; Keys 1 - 6

< Short press: BND button, to se-

lect the FM memory bank

and the AM waveband, source

selection to radio mode.

Long press: TS, to start the

Travelstore function.

= SRC button, to select the CD,

radio and CD changer or AUX

sources.

CONTROLS

1BA_LaguCD36_gb 3/14/06, 2:25 PM3

4

CONTENTS

Notes and accessories ................... 5

Road safety ............................................5

Installation ..............................................5

Accessories ............................................ 5

International telephone information ...........5

Detachable control panel ................ 6

Theft protection ...................................... 6

Detaching the control panel .....................6

Attaching the control panel ......................6

Switching on/off ............................. 7

Adjusting the volume ...................... 8

Setting the power-on volume ................... 8

Instantaneous volume reduction (mute) .... 8

Mute while telephoning ........................... 8

Confirmation beep ..................................9

Radio mode .................................... 9

Switching to radio mode .......................... 9

Setting the tuner .....................................9

Selecting the frequency range/ memory . 10

Tuning into a station .............................. 10

Storing stations ..................................... 10

Storing stations automatically

(Travelstore) .......................................... 11

Listening to preset stations .................... 11

Scanning receivable stations (SCAN) ....11

Setting the display................................. 11

CD mode ...................................... 12

Switching to CD mode ..........................12

Selecting tracks .................................... 12

Fast searching (audible) ........................12

Random play (MIX) ............................... 12

Scanning tracks (SCAN) ....................... 12

Repeating tracks (REPEAT) ................... 13

Pausing playback (PAUSE) ................... 13

Changing the display ............................ 13

Ejecting a CD ....................................... 13

CD changer mode ........................ 14

Switching to CD changer mode ............. 14

Selecting a CD ..................................... 14

Selecting tracks .................................... 14

Fast searching (audible) ........................14

Changing the display ............................ 14

Repeating individual tracks or

whole CDs (REPEAT) ........................... 14

Random play (MIX) ............................... 14

Scanning all tracks on all CDs (SCAN) .. 15

Pausing playback (PAUSE) ................... 15

CLOCK - Time ............................... 16

Briefly displaying the time ...................... 16

Setting the time ..................................... 16

Selecting 12/24-hour clock mode .......... 16

Displaying the time continuously

when the unit is off and the ignition is on 16

Briefly displaying the time when the

unit is switched off ................................ 16

Tone and volume distribution

settings ......................................... 17

Adjusting the bass settings .................... 17

Adjusting the treble settings .................. 17

Setting the left/right volume

distribution (balance) ............................. 17

Setting the front/back volume

distribution (fader) ................................. 17

Equalizer and X-BASS .................. 18

Setting the level display ................ 19

External audio sources ................. 19

Specifications ............................... 20

Installation instructions ............... 113

1BA_LaguCD36_gb 3/14/06, 2:25 PM4

5

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Notes and accessories

Thank you for deciding to purchase a

Blaupunkt product. We hope you enjoy

using this new piece of equipment.

Before using the device for the first time,

please read these instructions careful-

ly. The Blaupunkt editors are constant-

ly working on making the operating in-

structions clearer and easier to under-

stand. However, if you still have any

questions on how to operate the unit

please contact your dealer or the tele-

phone hotline for your country. You will

find the hotline telephone numbers print-

ed at the back of this booklet.

Road safety

Road safety has absolute prior-

ity. Only operate your car radio if the

road and traffic conditions allow you

to do so. Familiarise yourself with the

unit before setting off on your jour-

ney.

You should always be able to hear

police, fire and ambulance sirens in

good time from inside your vehicle.

For this reason, listen to your car

sound system at a moderate volume

level.

Installation

If you want to install your car radio your-

self, please read the installation and

connection instructions that follow these

operating instructions.

NOTES AND ACCESSORIES

Accessories

Only use accessories approved by Blau-

punkt.

Remote control

RC-12H is included. You can conve-

niently access the most important func-

tions of your car radio from the steering

wheel via the optional RC08 or RC10.

You cannot switch the device on/off us-

ing the remote control.

Amplifier

All Blaupunkt and Velocity amplifiers can

be used.

CD changer

You can connect the following Blaupunkt

CD changers: CDC A 08, IDC A 09 and

CDC A03.

International telephone

information

If you have any questions regarding the

operation of your car radio or if you re-

quire further information, please do not

hesitate to call us!

The information hotline numbers are

printed on the last page of these instruc-

tions.

1BA_LaguCD36_gb 3/14/06, 2:25 PM5

6

Detachable control panel

Theft protection

As a way of protecting your equipment

against theft, the unit is equipped with

a detachable control panel (release pan-

el). Without this control panel, the car

radio is worthless to a thief.

Protect your equipment against theft by

taking the control panel with you every

time you leave your vehicle. Do not

leave the control panel in your vehicle -

not even in a hidden place.

The control panel has been designed

to be easily use.

Note:

● Never drop the control panel.

● Never expose the control panel to

direct sunlight or other heat sourc-

es.

● Avoid making direct skin contact

with the control panel’s contacts. If

necessary, clean the contacts with

a lint-free cloth and some alcohol.

Detaching the control panel

2

➮ Press the button 2.

The control panel locking mechanism

opens.

➮ First, pull the control panel straight

off the unit and then out towards

the left.

● The unit switches off after the con-

trol panel is detached.

● All the current settings are saved.

● Any CD already inserted in the unit

remains there.

Attaching the control panel

➮ Slide the control panel from left to

right into the unit’s guide.

➮ Press the left-hand edge of the

control panel into the unit until it

clicks into place.

Note:

● When attaching the control panel,

make sure you do not press the

display.

If the device was still switched on when

you detached the control panel, it will

automatically switch on again with the

last settings activated (i.e. radio, CD, CD

changer or AUX) when the panel is re-

placed.

DETACHABLE CONTROL PANEL

1BA_LaguCD36_gb 3/14/06, 2:25 PM6

7

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

SWITCHING ON/OFF

Switching on/off

There are various ways of switching the

unit on/off:

Switching on/off using the vehicle

ignition

If the unit is correctly connected to the

vehicle’s ignition and it was not switched

off using ON/OFF button 1, it will

switch on/off simultaneously with the

ignition.

Switching on/off using the

detachable control panel

➮ Remove the control panel.

The unit switches off.

➮ Attach the control panel again.

The unit switches on. The last settings

(radio, CD, CD changer or AUX) will be

reactivated.

Switching on/off using button 1

➮ To switch the unit on, press button

1.

➮ To switch the unit off, press button

1 for longer than two seconds.

The unit switches off.

Note:

● If you switch on the unit when the

ignition is off, the unit will switch off

automatically after one hour to pre-

vent draining of the vehicle battery.

Switching on by inserting a CD

If the unit is switched off and there is no

CD inserted in the drive,

➮ gently insert the CD with the print-

ed side uppermost into the drive

until you feel some resistance.

The CD will be drawn automatically into

the drive.

You must not hinder or assist the drive

as it draws in the CD.

The unit switches on. CD playback be-

gins.

Note:

● The unit will remain off if the igni-

tion is off. To turn it on, press but-

ton 1 once.

1BA_LaguCD36_gb 3/14/06, 2:25 PM7

8

ADJUSTING THE VOLUME

Adjusting the volume

The volume can be adjusted in steps

from 0 (mute) to 66 (maximum).

➮ Increase the volume by pressing

the

button 4.

➮ Decrease the volume by pressing

the

button 4.

Setting the power-on volume

You can set the unit’s default power-on

volume.

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “ON VOLUME” appears

in the display.

➮ Set the power-on volume using the

and buttons 8.

To help you adjusting the volume more

easily, the audible volume level will in-

crease or decrease accordingly as you

make your changes.

If you select “LAST VOL”, the volume

played before the unit was last switched

off will be reactivated.

Note:

● To protect your hearing, the maxi-

mum switch-on volume under the

“LAST VOL” setting is “38”. If the

volume was higher before the unit

was switched off and “LAST VOL”

has been selected, the volume will

be set at “38” the next time the ra-

dio is switched on.

When you have finished making your

changes,

➮ press the MENU button 7 twice.

Instantaneous volume reduction

(mute)

This feature allows you to instanta-

neously reduce (mute) the volume to a

level preset by you.

➮ Briefly press button 1.

“MUTE” appears in the display.

To restore the volume,

➮ press button 1 again.

Setting the mute level

You can set the unit’s mute volume lev-

el.

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “MUTE LVL” appears in

the display.

➮ Set the mute level using the

and

buttons 8.

When you have finished making your

changes,

➮ press the MENU button 7 twice.

Mute while telephoning

If your unit is connected to a mobile tele-

phone, the car radio’s volume will be

muted as soon as you “pick up” the tele-

phone. “PHONE” shows in the display.

This requires the mobile telephone be

connected to the car radio as described

in the installation instructions.

1BA_LaguCD36_gb 3/14/06, 2:25 PM8

9

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

ADJUSTING THE VOLUME

Confirmation beep

For some functions you will hear a con-

firmation beep if you keep a button

pressed for longer than two seconds.

For instance, after storing a radio sta-

tion to a station button you will hear a

confirmation beep. The beep can be

switched on/off.

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “BEEP” appears in the

display.

➮ Use the

or buttons 8 to

switch between the options.

“OFF” means beep off, “ON” means the

beep is switched on.

➮ Press the MENU button 7.

Radio mode

Switching to radio mode

If you are listening to CD, CD changer

or AUX mode,

➮ press the BND•TS < button

or

➮ press the SRC button = repeated-

ly until “FM” or “AM” (“MW”) ap-

pears in the display.

Setting the tuner

In order to guarantee the perfect func-

tioning of the radio element, the unit

must be set for the region in which you

are located. You can choose between

Europe (EUROPE), America (USA),

Thailand (THAI) and South America

(S-AMERICA). The tuner comes from

the factory set for the region in which

the unit was sold. Should you encoun-

ter problems with radio reception,

please check this setting.

This set of instructions refers to the

“USA” setting.

➮ Switch off the device by pressing

button 1.

➮ Press and hold down the 1 and 5

buttons ; at the same time and

switch on the device again with

button 1.

“TUNER” is displayed.

➮ Press the buttons 8 within

the next 8 seconds and select your

tuner region.

RADIO MODE

1BA_LaguCD36_gb 3/14/06, 2:25 PM9

10

RADIO MODE

To save the setting,

➮ switch the device off and on again

or wait approx. 8 seconds. The ra-

dio starts with the last setting acti-

vated (radio, CD, CD changer or

AUX).

Selecting the frequency range/

memory

This unit can receive programmes

broadcast over the FM and AM frequen-

cy ranges. There are three memory

banks for the FM range and one for the

AM range. Six stations can be stored in

each memory bank.

Selecting the FM memory bank or

the AM frequency range

respectively

➮ Press the BND•TS button < to

switch between the FM memory

banks (FM1, FM2 and FMT) and

the AM frequency range respec-

tively.

Tuning into a station

There are various ways of tuning into a

station.

Automatic seek tuning

➮ Press the

or button 8.

The unit tunes into the next receivable

station.

Setting the sensitivity for station

seek tuning

You can configure the radio to only tune

into stations with a strong reception or

to also tune into those with a weak re-

ception.

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “SENS HI” or “SENS LO”

appears in the display.

“SENS HI” means that the tuner is highly

sensitive. “SENS LO” means it is set to

the lower sensitivity setting.

➮ Set the required sensitivity using

the

or buttons 8.

When you have finished making your

changes,

➮ press the MENU button 7.

Note:

● Different seek tuning sensitivities

can be set separately for FM and

AM respectively. To do so, activate

the relevant waveband.

Tuning into stations manually

You can also tune into stations manual-

ly.

➮ Press the

or button 8.

Storing stations

Storing stations manually

➮ Select the required memory bank

(FM1, FM2 or FMT) or the AM fre-

quency range.

➮ Tune into the station.

➮ Press one of the station buttons

1 - 6 ; for longer than 2 seconds

to store the station to that button.

1BA_LaguCD36_gb 3/14/06, 2:25 PM10

11

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

RADIO MODE

Storing stations automatically

(Travelstore)

You can automatically store six stations

with the strongest reception in the re-

gion. The stations are stored in the FMT

or AM memory depending on the se-

lected frequency range.

Note:

● Stations that were previously

stored in this memory are deleted

in the process.

➮ Press and hold the BND•TS button

< until the seek tuning starts.

The station storing procedure begins.

“FM TSTORE” or “AM TSTORE” ap-

pears in the display. After the process

is completed, the station that is stored

in location 1 of the respective memory

bank will be played.

Listening to preset stations

➮ Select the memory bank in which

the station was stored.

➮ Press the preset station button

1 - 6 ; of the station you want to

listen to.

Scanning receivable stations

(SCAN)

You can briefly play all the receivable

stations by activating the scan function.

You can set the scanning time to be-

tween 5 and 30 seconds in the menu.

Starting SCAN

➮ Keep the MENU button 7 pressed

until the scan process starts.

“SCAN” appears briefly in the display

followed by the current frequency (which

flashes).

Stopping SCAN and continuing

listening to a station

➮ Press the MENU button 7.

Scanning is stopped and the station that

was tuned into last will remain active.

Setting the scantime

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “SCAN TIME” appears in

the display.

➮ Set the required scantime using

the

or buttons 8.

When you have finished making your

changes,

➮ press the MENU button 7 twice.

Note:

● The set scantime also applies to

scanning in CD and CD changer

mode.

Setting the display

You can choose to continuous display

one of the followings:

● Band and Time

● Band and Frequency

➮ Keep the

DIS button : pressed

until the required display appears.

1BA_LaguCD36_gb 3/14/06, 2:25 PM11

12

CD mode

You can use this unit to play standard

CDs, CD-Rs and CD-RWs with a diam-

eter of either 5 or 3 inches.

To ensure the system functions proper-

ly, only use CDs labelled with the com-

pact disc logo. Problems might be ex-

perienced when trying to play copy-pro-

tected CDs. Blaupunkt cannot guaran-

tee the proper functioning of copy-pro-

tected CDs!

Risk of damage to the CD

drive! Contoured CDs (shape CDs)

are not suitable for playback in this

unit.

We accept no liability for any dam-

age to the CD drive or CD that may

occur as a result of the use of un-

suitable CDs.

Switching to CD mode

If there is no CD inserted in the drive

and the unit is playing Radio, CD

Changer or AUX mode,

➮ gently insert CD with the printed

side uppermost into the drive until

you feel some resistance.

The CD is drawn into the drive automat-

ically.

You must not hinder or assist the drive

as it draws in the CD.

CD playback begins.

Note:

● The unit will remain off if the igni-

tion is off. To turn it on and play the

inserted CD, press button 1 once.

If a CD is already inserted in the drive

and the unit is playing Radio, CD

Changer or AUX mode.

➮ Press the SRC button = repeat-

edly until “CD” appears in the dis-

play.

Playback begins from the point at which

it was last interrupted.

Selecting tracks

➮ Press one of the arrow buttons 8

to select the next or previous track.

If you press the

or button 8 once,

the current track will be played again

from the beginning.

Fast searching (audible)

To fast search backwards or forwards,

➮ keep one of the buttons 8

pressed until fast reversing / fast

forwarding begins.

Random play (MIX)

➮ Press button 5 MIX ;.

“MIX CD” appears briefly in the display

and the MIX symbol lights up. The next

randomly selected track will then be

played.

Stopping MIX

➮ Press button 5 MIX ; again.

“MIX OFF” appears briefly in the dis-

play and the MIX symbol disappears.

Scanning tracks (SCAN)

You can briefly play all the tracks on a

CD.

➮ Press the MENU button 7 for

longer than two seconds.

CD MODE

1BA_LaguCD36_gb 3/14/06, 2:25 PM12

13

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

CD MODE

The next track will then be played for

scantime as set in the “Setting the

scantime”.

Note:

● You can set the scantime. For fur-

ther details, please read the sec-

tion entitled “Setting the scantime”

in the “Radio mode” chapter.

Stopping SCAN and continuing

playback

➮ To stop scanning, press the MENU

button 7.

The current track will then continue to

be played.

Repeating tracks (REPEAT)

➮ If you want to repeat a track, press

button 4 RPT ;.

“RPT TRCK” appears briefly in the dis-

play and the RPT symbol lights up. The

track is repeated until you deactivate

RPT.

Cancelling repeat

➮ If you want to stop the repeat func-

tion, press button 4 RPT ; again.

“RPT OFF” appears briefly in the dis-

play and the RPT symbol disappears.

Normal playback is then continued.

Pausing playback (PAUSE)

➮ Press button 3 ;.

“PAUSE” appears in the display.

Cancelling pause

➮ Press button 3 ; while in

pause mode.

Playback is continued.

Changing the display

Two options are available:

● Track number and clock.

● Track number and playing time.

➮ Press the DIS button : for

longer than two seconds until the

required display appears.

Ejecting a CD

➮ Press the button 3.

➮ Remove the CD

Notes:

● An ejected CD will be reloaded into

the unit if not removed within 10

seconds to protect it from acciden-

tal damage.

● You may also eject a CD when the

unit is off, or when CD is not play-

ing.

1BA_LaguCD36_gb 3/14/06, 2:25 PM13

14

CD changer mode

Note:

● Information on handling CDs, in-

serting CDs and operating the CD

changer can be found in the oper-

ating instructions supplied with

your CD changer.

Switching to CD changer mode

➮ Press the SRC button = repeat-

edly until “CHANGER” appears in

the display.

The CD Changer will resume playback

from where it was last played previous-

ly.

Selecting a CD

➮ To move up/ down from one CD to

another, press the

or button

8 once or several times.

➮ An empty CD magazine slot will be

skipped in the CD selection pro-

cess.

Selecting tracks

➮ To move up/ down from one track

to another on the current CD, press

the

or button 8 once or sev-

eral times.

Fast searching (audible)

To fast search backwards or forwards,

➮ keep one of the or buttons 8

pressed until fast reversing/fast for-

warding begins.

Changing the display

5 options are available:

● Track number and play time

● Track number and clock

● CD number and track number

● CD number and clock

● CD number and play time

➮ Press the

DIS button : once or

several times for longer than two

seconds until the required display

appears.

Repeating individual tracks or

whole CDs (REPEAT)

➮ If you wish to repeat the current track,

briefly press button 4 RPT ;.

“RPT TRCK” appears briefly and RPT

lights up in the display.

➮ If you wish to repeat the current

CD, press button 4 RPT ; longer

than two seconds.

“RPT DISC” appears briefly and RPT

lights up in the display.

Cancelling repeat

➮ If you want to stop the repeat func-

tion for the current track or CD,

press button 4 RPT ; briefly and

“RPT OFF” appears briefly in the

display and RPT disappears.

Random play (MIX)

➮ To play all the tracks on the current

CD in random order, briefly press

button 5 MIX ;.

“MIX CD” appears briefly and MIX lights

up in the display.

CD CHANGER MODE

1BA_LaguCD36_gb 3/14/06, 2:25 PM14

15

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

CD CHANGER MODE

➮ To play the tracks on all the insert-

ed CDs in random order, press but-

ton 5 MIX ; longer than two sec-

onds.

“MIX ALL” appears briefly and MIX lights

up in the display.

Stopping MIX

➮ Press button 5 MIX ; briefly and

“MIX OFF” appears briefly in the

display and MIX disappears.

Scanning all tracks on all CDs

(SCAN)

➮ To briefly play all the tracks on all

inserted CDs in ascending order,

press the MENU button 7 for

longer than two seconds.

“TRK SCAN” appears briefly follows by

blinking the track number of the CD

track being scanned.

Stopping SCAN

➮ To stop scanning, briefly press the

MENU button 7.

The current track will then continue to

be played.

Note:

● You can set the scantime. For fur-

ther details, please read the sec-

tion entitled “Setting the scantime”

in the “Radio mode” chapter.

Pausing playback (PAUSE)

➮ Press button 3 ;.

“PAUSE” appears in the display.

Cancelling pause

➮ Press button 3 ; while in

pause mode.

Playback is continued.

1BA_LaguCD36_gb 3/14/06, 2:25 PM15

16

CLOCK - Time

Briefly displaying the time

➮ To display the time, briefly press

the

DIS button :.

Setting the time

➮ To set the time, press the MENU

button 7.

➮ Press the

or button 8 repeat-

edly until “CLOCK SET” appears in

the display.

➮ Press the

button 8.

The time appears in the display. The

minutes flash on and off and can be

adjusted.

➮ Adjust the minutes using the

buttons 8.

➮ Once you have set the minutes,

press the

button 8. The hours

start flashing.

➮ Adjust the hours using the

but-

tons 8.

When you have finished making your

changes,

➮ press the MENU button 7 twice.

Selecting 12/24-hour clock

mode

➮ Press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “12H MODE” or “24H

MODE” appears in the display.

➮ Press the

or button 8 to

switch between the modes.

When you have finished making your

changes,

➮ press the MENU button 7.

Displaying the time continuously

when the unit is off and the

ignition is on

“CLOCK ON” setting in the menu allows

you to display the time when the unit is

off and the vehicle ignition is on,

➮ press the MENU button 7.

➮ Press the

or button 8 repeat-

edly until “CLOCK OFF” or

“CLOCK ON” appears in the dis-

play.

➮ Press the

or button 8 to

switch between the ON/OFF set-

tings.

When you have finished making your

changes,

➮ press the MENU button 7.

Briefly displaying the time when

the unit is switched off

To briefly display the time when the unit

is off,

➮ press the

DIS button :.

The time is displayed for eight seconds.

CLOCK - TIME

1BA_LaguCD36_gb 3/14/06, 2:25 PM16

17

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Tone and volume

distribution settings

You can adjust the tone settings (bass

and treble) separately for each source

(radio, CD, CD changer and AUX).

The volume distribution (balance and

fader) settings apply to all audio sourc-

es.

Adjusting the bass settings

➮ Press the AUDIO button 6.

“BASS” appears in the display.

➮ Press the

or button 8 to ad-

just the bass.

When you have finished making your

changes,

➮ press the AUDIO button 6.

Adjusting the treble settings

➮ Press the AUDIO button 6.

“BASS” appears in the display.

➮ Press the

button 8

repeatedly until “TREBLE” appears

in the display.

➮ Press the

or button 8 to ad-

just the treble.

When you have finished making your

changes,

➮ press the AUDIO button 6.

Setting the left/right volume

distribution (balance)

➮ To set the left/right volume distribu-

tion (balance), press the AUDIO

button 6.

“BASS” appears in the display.

➮ Press the

button 8 repeatedly

until “BAL” appears in the display.

➮ Press the

or button 8 to

adjust the balance (right/left).

When you have finished making your

changes,

➮ press the AUDIO button 6.

Setting the front/back volume

distribution (fader)

➮ To set the front/back volume distri-

bution (fader), press the AUDIO

button 6.

“BASS” appears in the display.

➮ Press the

button 8 repeatedly

until “FADER” appears in the dis-

play.

➮ Press the

or button 8 to ad-

just the fader (front/back).

When you have finished making your

changes,

➮ press the AUDIO button 6.

TONE AND VOLUME DISTRIBUTION SETTINGS

1BA_LaguCD36_gb 3/14/06, 2:25 PM17

18

Equalizer and X-BASS

X-BASS

X-Bass means increased bass at low

volumes.

You can set the X-Bass in steps rang-

ing from OFF to three. Three means that

the X-Bass boost is set to maximum and

OFF means that X-Bass is switched off.

Note:

● X-BASS setting is shared by all au-

dio source (radio, CD, CD-changer

or AUX).

➮ To set the X-BASS, press the

X-BASS 9 button.

➮ Press the

or button 8 to

choose between the possible set-

tings.

➮ Press the X-BASS 9 button once

you have completed the setting.

Selecting a preset sound effect

(EQ)

You can select a preset sound effect for

the following styles of music:

● ROCK

● POP

● CLASSIC

The settings for these music styles have

already been programmed.

To select one of the sound presets,

➮ press the AUDIO 6 button.

“BASS” appears on the display.

➮ Press the

button 8 repeatedly

until one of the sound effect op-

tions appears on the display.

➮ Press the

or button 8 to

choose between the presets.

If you want to deactivate the sound pre-

set,

➮ choose “EQ OFF” from the avail-

able options.

➮ Press the AUDIO 6 button once

you have completed the setting.

Note:

● The selected preset sound effect is

applied to all audio sources.

EQUALIZER AND X-BASS

1BA_LaguCD36_gb 3/14/06, 2:25 PM18

19

FRANÇAIS

ENGLISH

ESPAÑOL

PORTUGUÊS

Setting the level display

The level display briefly provides a sym-

bolic display of the volume and the au-

dio control settings whilst you are ad-

justing them.

When settings are not being made, the

level display indicates the music level

of the car radio.

You can switch the music level display

on/off in the menu.

➮ Press the MENU button 7.

“MENU” appears on the display.

➮ Press the

or button 8 repeat-

edly until “PEAK LVL” appears on

the display.

➮ Press the

or button 8 to

choose between “PEAK ON” and

“PEAK OFF”.

When you have finished making your

changes,

➮ press the MENU button 7 twice.

External audio sources

Instead of connecting a CD changer,

you can connect another audio source

equipped with a line output. The audio

source, for example, can be a portable

CD player, MiniDisc player or MP3 play-

er.

The AUX input must be activated in the

menu.

If you want to connect an external au-

dio source, you will need an adapter

cable. You can obtain this adapter ca-

ble (BP no.: 7 607 897 093) from your

authorised Blaupunkt dealer.

Switching the AUX input on/off

➮ Press the MENU button 7.

“MENU” appears in the display.

➮ Press the

or button 8 repeat-

edly until “AUX OFF” or “AUX ON”

appears in the display.

➮ Press the

or button 8 to

switch AUX on/off.

When you have finished making your

changes,

➮ press the MENU button 7.

Note:

● If the AUX input is switched on it

can be selected by pressing the

SRC button = and it is shown as

“AUX INPUT” on the display.

LEVEL DISPLAY

EXTERNAL AUDIO SOURCES

1BA_LaguCD36_gb 3/14/06, 2:25 PM19

20

Specifications

Amplifier

Output power: 15W RMS x 4ch @ 14.4V @ 4ohm @ 1% THD

Tuner

Frequency ranges USA:

FM: 87.5 - 107.9 MHz (200 kHz step)

AM: 530 - 1710 kHz (10 kHz step)

Frequency ranges Europe:

FM: 87.5 - 108 MHz (100 kHz step auto/50 kHz manual)

AM: 531 - 1602 kHz (9 kHz step)

Frequency ranges Thailand:

FM: 87.5 - 108 MHz (50 kHz step auto/25 kHz step manual)

AM: 531 - 1602 kHz (9 kHz step)

Frequency ranges South America:

FM: 87.5 - 107.9 MHz (100 kHz step auto/50 kHz step manual)

AM: 530 - 1710 kHz (10 kHz step)

FM mono sensitivity:

17 dbf

FM frequency response:

35 - 16,000 Hz

CD

Frequency response:

20 - 20,000 Hz

Pre-amp out

4 channels: 2 V

Input sensitivity

AUX input: 2 V / 6 kΩ

Subject to changes!

SPECIFICATIONS

1BA_LaguCD36_gb 3/14/06, 2:25 PM20

La page charge ...

Blaupunkt LAGUNA CD36 Le manuel du propriétaire

Ce manuel convient également à

Blaupunkt LAGUNA CD36 Le manuel du propriétaire

dans d''autres langues

Documents connexes