YOKOGAWA AQ6373B-01 Getting Started Manual

User’s

Manual

AQ6373B

Optical Spectrum Analyzer

Getting Started Guide

IM AQ6373B-02EN

5th Edition

Product Registration

Thank you for purchasing YOKOGAWA products.

YOKOGAWA provides registered users with a variety of information and

services.

Please allow us to serve you best by completing the product registration

form accessible from our homepage.

http://tmi.yokogawa.com/

PIM 103-03E

i

IM AQ6373B-02EN

Foreword

Thank you for purchasing the AQ6373B Optical Spectrum Analyzer. This instrument

enables high speed measurement of the optical properties of LD and LED light sources,

and other devices. To improve ease of use, it includes mouse-based user operation and

a brand-new zoom function.

This getting started guide describes the instrument’s functions, operating procedures,

and handling precautions, and provides other important information for use of the

instrument. For correct operation, please read this manual thoroughly before use. After

reading this manual, keep it in a convenient location for quick reference in the event a

question arises during operation. There are three manuals for the AQ6373B including this

one. Read them along with this manual.

Manual Title Manual No. Description

AQ6373B Optical Spectrum

Analyzer

User’s Manual

IM AQ6373B-01EN The manual is located on the CD included in

your package (pdf format). Explains all functions

and operating procedures of the AQ6373B

except remote control and program functions.

AQ6370C/AQ6370D/

AQ6373/AQ6373B/AQ6375

Optical Spectrum Analyzer

Remote Control User’s

Manual

IM AQ6370C-17EN The manual is located on the CD included in

your package (pdf format). Explains functions for

controlling the instrument with communication

commands and program functions.

AQ6373B Optical Spectrum

Analyzer Getting Started

Guide

IM AQ6373B-02EN This guide. Provided as a printed manual.

This guide explains the handling precautions,

basic operations, and specifications of the

AQ6373B.

Model AQ6373B-01,

AQ6373B-02

AQ6373B Optical Spectrum

Analyzer Limited model

User’s Manual

IM AQ6373B-51EN Explains the specifications of the limited model

of the AQ6373B.

The “-EN” in the manual number is the language code.

Contact information of Yokogawa offices worldwide is provided on the following sheet.

Document Description Description

PIM 113-01Z2 List of worldwide contacts

Notes

• The contents of this manual are subject to change without prior notice as a result

of improvements in the instrument’s performance and functions. Display contents

illustrated in this manual may differ slightly from what actually appears on your screen.

• Every effort has been made in the preparation of this manual to ensure the accuracy

of its contents. However, should you have any questions or find any errors, please

contact your nearest YOKOGAWA dealer.

• Copying or reproducing all or any part of the contents of this manual without the

permission of Yokogawa Test & Measurement Corporation is strictly prohibited.

Trademarks

• Microsoft and Windows are trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

• Adobe, Acrobat, and PostScript are trademarks or registered trademarks of Adobe

Systems incorporated.

• The company and product names used in this manual are not accompanied by the

trademark or registered trademark symbols (TM, ®)

• Other company and product names are trademarks or registered trademarks of their

respective companies.

5th Edition : April 2019 (YMI)

ii

IM AQ6373B-02EN

Revisions

• 1st Edition: March 2015

• 2nd Edition: April 2017

• 3rd Edition: October 2017

• 4th Edition: October 2018

• 5th Edition: April 2019

iii

IM AQ6373B-02EN

Checking the Contents of the Package

After opening the package, check the following items before beginning use. If any of the

contents are incorrect, missing, or appear to be abnormal, please contact your Yokogawa

dealer or representative.

AQ6373B Main Unit

Check that the model and suffix code on the name plate on the rear of the instrument

match those of your order. When contacting the dealer from which you purchased the

instrument, please give them the instrument number.

MODEL Suffix Code

1

Description

AQ6373B Optical Spectrum Analyzer AQ6373B

Specification -02 Limited Model

-01 Limited Model

-12 Standard Model

-10 Standard Model

Built-in light -L1 Optical alignment source

source

Power cord

2

-D

UL/CSA standard and PSE compliant,

Rated voltage: 125 V

-F VDE/Korean standard, Rated voltage: 250 V

-R Australian standard, Rated voltage: 250 V

-Q British standard, Rated voltage: 250 V

-H Chinese standard, Rated voltage: 250 V

-N Brazilian standard, Rated voltage: 250 V

-T Taiwanese standard, Rated voltage: 125 V

-B Indian standard, Rated voltage: 250 V

-U IEC Plug Type B, Rated voltage: 250 V

-Y No power cord included.

3

1 For products whose suffix code contains “Z,” an exclusive manual may be included. Please

read it along with the standard manual.

2 Make sure that the attached power cord meets the designated standards of the country and

area that you are using it in.

3 Prepare a power cord that complies with the standard specified by the country or region that

the instrument will be used in.

• No. (Instrument Number)

Please contact your nearest Yokogawa representative.

AQ6373B-02, -12 AQ6373B-01, -10

iv

IM AQ6373B-02EN

Checking the Contents of the Package

Standard Accessories

Part Name Model or Part No. Quantity Specifications and Notes

Power cord

*

A1006WD 1 UL/CSA standard and PSE compliant

A1009WD VDE/Korean standard

A1024WD Australian standard

A1054WD British standard

A1064WD Chinese standard

A1088WD Brazilian standard

A1100WD Taiwanese standard

A1101WD Indian standard

A1102WD IEC Plug Type B

Rubber feet A9088ZM 2 1 A9088ZM sheet

Manuals

Printed Manuals IM AQ6373B-02EN 1 Getting Started Guide

IM AQ6373B-51EN 1 Accompanying the limited model only

IM AQ6373B-92Z1 1 Document for China

PIM 113-01Z2 1 List of worldwide contacts

Manual CD B8092YB 1 Contains PDFs of the user’s manuals

(For the types of manuals that CD

contains, see Manual CD below.)

Standard accessories are not covered by warranty of this instrument.

* Make sure that the attached power cord meets the designated standards of the country and

area that you are using it in. If the suffix code is -Y, a power cord is not included.

Manual CD

The English directory in the manual CD contains the PDF files shown below. The CD

also contains Japanese manuals.

File Name Manual Title Manual No.

Features & Operation Manual.pdf AQ6373B Optical Spectrum Analyzer IM AQ6373B-01EN

User’s Manual

Communication Interface.pdf AQ6370C/AQ6370D/AQ6373/ IM AQ6370C-17EN

AQ6373B/AQ6375 Optical Spectrum

Analyzer Remote Control

User’s Manual

To view the PDF data, you need Adobe Acrobat Reader or a software application that

can open PDF data.

WARNING

Never play this manual CD, which contains the user’s manuals, in an audio CD

player. Doing so may cause loss of hearing or speaker damage due to the large

sounds that may be produced.

French

AVERTISSEMENT

Ce CD contient les manuels d’utilisation. Ne jamais insérer ce CD dans un lecteur

de CD audio. Cela pourrait entraîner une perte d’audition ou l’endommagement

des enceintes en raison du volume potentiellement élevé des sons produits.

v

IM AQ6373B-02EN

Safety Precautions

This product is designed to be used by a person with specialized knowledge.

This instrument is an IEC safety class I (provided with terminal for protective earth

grounding). The general safety precautions described herein must be observed during all

phases of operation. If the instrument is used in a manner not specified in this manual,

the protection provided by the instrument may be impaired.

This manual is an essential part of the product; keep it in a safe place for future

reference. Yokogawa Electric Corporation assumes no liability for the customer’s failure

to comply with these requirements.

The following symbols are used on this instrument.

Refer to the user's manual.

This symbol appears on dangerous locations on the instrument which require

special instructions for proper handling or use. The same symbol appears in the

corresponding place in the manual to identify those instructions.

Alternating current

ON(power)

OFF(power)

French

À manipuler délicatement.

Toujours se reporter aux manuels d'utilisation et d'entretien. Ce symbole a été

apposé aux endroits dangereux de l'instrument pour lesquels des consignes

spéciales d'utilisation ou de manipulation ont été émises. Le même symbole

apparaît à l'endroit correspondant du manuel pour identifier les consignes qui s'y

rapportent.

Courant alternatif

Marche (alimentation)

Arrêt (alimentation)

vi

IM AQ6373B-02EN

Failure to comply with the precautions below could lead to injury or death or

damage to the instrument.

WARNING

• Use the Instrument Only for Its Intended Purpose

The optical measuring instrument is designed to measure the optical

characteristics of light sources and evaluate their performance. Do not use this

instrument for anything other than as an optical measuring instrument.

• Check the Physical Appearance

Do not use the instrument if there is a problem with its physical appearance.

• Use the Correct Power Supply

Make sure that the power supply voltage matches the instrument’s rated supply

voltage and that it does not exceed the maximum voltage range of the power

cord to use.

• Use the Correct Power Cord and Plug

To prevent the possibility of electric shock or fire, be sure to use the power cord

for the instrument. The main power plug must be plugged into an outlet with a

protective earth terminal. Do not invalidate this protection by using an extension

cord without protective earth grounding.

Further, do not use this power cord with other instruments.

• Connect the Protective Grounding Terminal

Make sure to connect the protective earth to prevent electric shock before

turning ON the power. The power cord that you can use for the instrument is a

three-prong cord. Connect the power cord to a properly grounded three-prong

outlet.

• Do not Impair the Protective Grounding

Never cut off the internal or external protective earth wire or disconnect the

wiring of the protective earth terminal. Doing so poses a potential shock hazerd.

• Do not Operate with Defective Protective Grounding or Fuse

Do not operate the instrument if the protective earth or fuse might be defective.

Make sure to check them before operation.

• Reference light source output light (when the built-in light source

specification is -L1)

The instrument has a built-in reference light source for alignment adjustment,

and infrared light is always being output from the optical output connector. Never

look into the optical output connector. Infrared light entering the eyes can cause

severe injury and loss of vision.

• Do not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable liquids or vapors.

Operation in such environments constitutes a safety hazard.

• Do Not Remove the Covers or Disassemble or Alter the Instrument

Only qualified YOKOGAWA personnel may remove the covers and disassemble

or alter the instrument.

Opening the cover is dangerous, because some areas inside the instrument

have high voltages.

• Install or Use the Instrument in Appropriate Locations

• This instrument is designed to be used indoors. Do not install or use it outdoors.

• Install the instrument so that you can immediately remove the power cord if

an abnormal or dangerous condition occurs.

Safety Precautions

vii

IM AQ6373B-02EN

CAUTION

Operating Environment Limitations

This product is a Class A (for industrial environment) product. Operation of this

product in a residential area may cause radio interference in which case the user is

required to correct the interference.

French

AVERTISSEMENT

• Utiliser l’instrument aux seules fins prévues

Cet instrument de mesure optique est prévu pour mesurer les caractéristiques

optiques des sources lumineuses et évaluer leur performance. Ne pas utiliser

cet instrument à d’autres fins que celles de mesure optique.

• Inspecter l’apparence physique

Ne pas utiliser l’instrument si son intégrité physique semble être compromise.

• Vérifier l’alimentation

Assurez-vous que la tension d’alimentation correspond à la tension d’alimentation

nominale de l’appareil et qu’elle ne dépasse pas la plage de tension maximale

du cordon d’alimentation à utiliser.

• Utiliser le cordon d’alimentation et la fiche adaptés

Pour éviter tout risque de choc électrique, utiliser exclusivement le cordon

d’alimentation prévu pour cet instrument. La fiche doit être branchée sur une

prise secteur raccordée à la terre. En cas d’utilisation d’une rallonge, celleci

doit être impérativement reliée à la terre. Par ailleurs, ne pas utiliser ce cordon

d’alimentation avec d’autres instruments.

• Brancher la prise de terre

Avant de mettre sous tension, veiller à brancher la mise à la terre de protection

afin d’éviter les chocs électriques. Le cordon d’alimentation que vous utilisez

pour l’instrument est un cordon à trois broches.

Brancher le cordon d’alimentation sur une prise de courant à trois plots et mise

à la terre.

• Ne pas entraver la mise à la terre de protection

Ne jamais neutraliser le fil de terre interne ou externe, ni débrancher la borne

de mise à la terre. Cela pourrait entraîner un choc électrique ou endommager

l’instrument.

• Ne pas utiliser avec un conducteur de terre ou un fusible défectueux

Ne pas utiliser l’instrument si le conducteur de terre ou le fusible est défectueux.

Vérifier le conducteur de terre et le fusible avant d’utiliser l’instrument.

• Source de lumière de référence (lorsque la source de lumière intégrée

correspond aux caractéristiques L1)

Cet instrument dispose d’une source de lumière de référence intégrée pour

les ajustements d’alignement. La lumière infrarouge est toujours émise depuis

le connecteur de sortie optique. Ne regardez jamais directement dans le

connecteur de sortie optique. La lumière infrarouge risquerait de gravement

vous blesser ou de provoquer une perte de vision.

Safety Precautions

viii

IM AQ6373B-02EN

• Ne pas utiliser dans un environnement explosif

Ne pas utiliser l’instrument en présence de gaz ou de vapeurs inflammables.

Cela pourrait être extrêmement dangereux.

• Ne pas retirer le capot, ni démonter ou modifier l’instrument

Seul le personnel YOKOGAWA qualifié est habilité à retirer le capot et à

démonter ou modifier l’instrument. Certains composants à l’intérieur de

l’instrument sont à haute tension et par conséquent, représentent un danger.

• Installer et utiliser l’instrument aux emplacements appropriés

• Ne pas installer, ni utiliser l’instrument à l’extérieur ou dans des lieux exposés

à la pluie ou à l’eau.

• Installer l’instrument de manière à pourvoir immédiatement le débrancher du

secteur en cas de fonctionnement anormal ou dangereux.

ATTENTION

Limitations relatives à l’environnement opérationnel

Ce produit est un produit de classe A (pour environnements industriels). L’utilisation

de ce produit dans un zone résidentielle peut entraîner une interférence radio que

l’utilisateur sera tenu de rectifier.

Safety Precautions

ix

IM AQ6373-02EN

Alert mark

Safety Precautions

5 Installing the Instrument

7 Turning the Power ON/OFF

Safety Precautions for Laser Products (when the built-in light source

specification is -L1)

This instrument uses a laser light source. This instrument is a Class 1 laser product

as defined by EN 60825-1:2014/IEC 60825-1:2007 Safety of Laser Products-Part 1:

Equipment Classification, Requirements and User’s Guide. In addition, this instrument

complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

Laser Class 1 Label

AQ6373B-02,

-12

AQ6373B-01, -10

Laser Class 1 Label

Information about the Laser Light Source Used

Class Laser Type Wavelength Maximum

Output Power

Diameter of

Mode Field

Repetation

Rate

Numerical

Aperture

1 LED 850nm 0.1mW 50µm CW 0.275

Safety Precautions

x

IM AQ6373B-02EN

Regulations and Sales in Each Country or Region

Waste Electrical and Electronic Equipment

Waste Electrical and Electronic Equipment (WEEE), Directive

(This directive is valid only in the EU.)

This product complies with the WEEE directive marking requirement. This marking

indicates that you must not discard this electrical/electronic product in domestic

household waste.

Product Category

With reference to the equipment types in the WEEE directive , this product is

classified as a “Monitoring and Control instrumentation” product.

When disposing of products in the EU, contact your local Yokogawa Europe B. V.

office. Do not dispose in domestic household waste.

EU Battery Directive

(This directive is valid only in the EU.)

Batteries are included in this product. This marking indicates they shall be sorted

out and collected as ordained in the EU battery directive.

Battery type

Lithium battery

You cannot replace batteries by yourself. When you need to replace batteries,

contact your local Yokogawa Europe B.V.office.

Authorized Representative in the EEA

Yokogawa Europe B. V. is the authorized representative of Yokogawa Test &

Measurement Corporation in the EEA for this product. To contact Yokogawa Europe B. V.,

see the separate list of worldwide contacts, PIM 113-01Z2.

關於在台灣銷售

This section is valid only in Taiwan.

關於在台灣所販賣的符合其相關規定的電源線 A1100WD 的限用物質含量信息，請至下麵的

網址進行查詢

https://tmi.yokogawa.com/support/service-warranty-quality/product-compliance/

xi

IM AQ6373B-02EN

Conventions Used in This Manual

Safety Markings

The following markings are used in this manual.

Improper handling or use can lead to injury to the user or damage to

the instrument. This symbol appears on the instrument to indicate

that the user must refer to the user's manual for special instructions.

The same symbol appears in the corresponding place in the user's

manual to identify those instructions. In the manual, the symbol is

used in conjunction with the word “WARNING” or “CAUTION.”

WARNING

Calls attention to actions or conditions that could cause serious or

fatal injury to the user, and precautions that can be taken to prevent

such occurrences.

CAUTION

Calls attentions to actions or conditions that could cause light injury to

the user or damage to the instrument or user’s data, and precautions

that can be taken to prevent such occurrences.

French

AVERTISSEMENT

Attire l’attention sur des gestes ou des conditions susceptibles

de provoquer des blessures graves (voire mortelles), et sur les

précautions de sécurité pouvant prévenir de tels accidents.

ATTENTION

Attire l’attention sur des gestes ou des conditions susceptibles de

provoquer des blessures légères ou d’endommager l’instrument ou les

données de l’utilisateur, et sur les précautions de sécurité susceptibles

de prévenir de tels accidents.

Note

Calls attention to information that is important for proper operation of

the instrument.

xii

IM AQ6373B-02EN

Notations Used on Pages Describing Operating Procedures

On pages that describe the operating procedures, the following notations are used to

distinguish the procedures from their explanations.

Procedure

This subsection contains the operating procedure used to carry out

the function described in the current chapter. All procedures are

written with inexperienced users in mind; experienced users may not

need to carry out all the steps.

Explanation

This subsection describes the setup parameters and the limitations

on the procedures.

Notations Used in the Procedures

Panel Keys and Soft keys

Bold characters used in the procedural explanations indicate characters that are marked on the

panel keys or the characters of the soft keys displayed on the screen menu.

Unit

k: Denotes “1000.” Example: 100kS/s

K: Denotes “1024.” Example: 459KB (file data size)

Conventions Used in This Manual

xiii

IM AQ6373B-02EN

Flow of Operation

The figure below is provided to familarize the first-time user with the general flow of this

instrument operation. For a description of each item, see the relevant section or chapter

of IM AQ6373B-01EN.

Preparing for Measurement

Setting Conditions and Measuring

Waveform Display

Installing the Instrument

Turning the Power ON/OFF

Auto Sweep Setting and

Measurement Other Settings

Waveform Display

Displaying Calculated Waveforms

Marker Display

Searching

Waveform Analysis

GO/NO-GO Judgment

Analysis Data Logging

Saving Display Data and Printing Out

Storage Media

Saving Data

Chapter 5 in IM AQ6373B-02EN

Chapter 7 in IM AQ6373B-02EN

Section 2.1

Section 4.1

Section 4.2 to 4.11

Section 5.1 to 5.4

Section 5.5

Section 5.9

Section 5.13 and 5.14

Section 6.1 to 6.9

Section 6.11

Section 6.14

Section 7.1

Section 7.2 to 7.9

Measurement Start (Sweep)

External Trigger Measurement

Smoothing

Section 4.13

Section 4.16

Section 4.18

Alignment Adjustment

(Wavelength Calibration)

xiv

IM AQ6373B-02EN

Contents

Checking the Contents of the Package .......................................................................................... iii

Safety Precautions ...........................................................................................................................v

Regulations and Sales in Each Country or Region ..........................................................................x

Conventions Used in This Manual ..................................................................................................xi

Flow of Operation ......................................................................................................................... xiii

1 Front Panel ..............................................................................................................................1

2 Rear Panel ...............................................................................................................................2

3 Panel Keys and Knobs ............................................................................................................3

4 LCD Screen .............................................................................................................................6

5 Installing the Instrument ...........................................................................................................8

6 Connecting a Communication Interface .................................................................................12

7 Turning the Power ON/OFF ...................................................................................................14

8 Connecting the DUT ..............................................................................................................20

9 Specications .........................................................................................................................24

10 External Dimensions ..............................................................................................................27

1

IM AQ6373B-02EN

1 Front Panel

Front Panel

AQ6373B

OPTICAL SPECTRUM ANALYZER

USB

POWER

FUNCTION

DATA ENTRY

CENTER

SWEEP

SPAN

LEVEL

ZOOM

SETUP

MARKER

DISPLAY

PEAK

SEARCH

TRACE

ANALYSIS

USER

MEMORY

FILE

SYSTEM

ADVANCE

PROGRAM

OREMOTE

UNDO/

LOCAL

HELP

COARSE

7

8

9

4

5

6

1

2

3

0

.

-

BACK

SPASE

nm/

ENTER

m/

ENTER

OPTICAL INPUT

(

600 1700nm

)

CALIBRATION

OUTPUT

1 2

3

4

5

6

7

8

9

10

COPY

PRESET

11

12

No. Name Function

1 LCD display Displays measured waveform, measurement conditions,

measurement values, etc.

2 Soft key section Used to execute the functions assigned to the soft keys on

the right side of the LCD display

3 FUNCTION section Used to enter settings pertaining to all measurements

(sweep, measurement conditions, data analysis, and

various functions)

4 DATA ENTRY section Used for measurement condition parameter input, label

input, etc.

5 POWER Used to start and shut down the instrument.

6 USB interface Used to connect USB storage media

7 UNDO/LOCAL See the following table(1.3 Panel keys and Knobs)

8 HELP Used to check the contents of the soft key menu displayed

on the screen.

9 OPTICAL INPUT Optical input connector

10 CALIBRATION OUTPUT Reference light source optical output connector used for

alignment adjustments and wavelength calibration (when

the built-in light source specification is -L1)

11 COPY Save the screen as an image file.

12 PRESET Clears all internal settings of the AQ6373B except for the

remote interface (ETHERNET, GP-IB, and RS232) settings.

2

IM AQ6373B-02EN

2 Rear Panel

Rear Panel

1

2

3

4

5

6

7

8 9

10

11

1

2

3 4

5

6

7

8 9

10

11

AQ6373B-02, -12 AQ6373B-01, -10

No. Name Function

1 GP-IB GP-IB port for controlling this unit through an external

computer

2 TRIGGER IN Input connector for synchronous signals for the

synchronous measurement function with the Tunable Laser

Source

3 TRIGGER OUT Output connector for synchronous signals for the

synchronous measurement function with the Tunable Laser

Source

4 ANALOG OUT Analog output

5 MAIN POWER Used to turn the main power ON/OFF

6 Power cord connector Connect the power cord to this connector

7 VIDEO OUT (SVGA) Analog RGB video signal (SVGA-compliant) interface

8 SERIAL RS-232 interface

9 ETHERNET Ethernet Interface

10 USB interface Used to connect USB storage media or USB mouse

11 Exhaust holes

3

IM AQ6373B-02EN

3 Panel Keys and Knobs

FUNCTION Section

The FUNCTION section contains 17 function keys and 4 auxiliary keys. When you press

a function key, information about the function is displayed on the soft key menu located

on the right side of the LCD display.

SWEEP

The SWEEP key contains functions related to sweeping. When you press the SWEEP

key, the soft key menu for sweeping appears.

CENTER

The CENTER key contains functions related to setting the center wavelength and center

frequency for measurements. The soft key functions change depending on whether the

screen display mode is wavelength display mode or frequency display mode.

SPAN

The SPAN key contains functions pertaining to settings for the wavelength span or

frequency span being measured. The soft key functions change according to whether the

screen display mode is wavelength display mode or frequency display mode.

LEVEL

The LEVEL key contains functions related to level axis settings.When you press the

LEVEL key, the soft key menu for setting reference level appears.

SETUP

The SETUP key contains functions related to measurement condition settings.

ZOOM

The ZOOM key contains the zoom function, which allows the user to freely enlarge or

reduce a measured waveform in order to check a small area of the measured waveform,

or to check the overall waveform.

This key is used to set the waveform enlarged/reduced display conditions.

DISPLAY

The DISPLAY key contains functions related to screen display.This key is used to set the

screen to upper/lower 2-split display mode (split mode).

TRACE

The TRACE key contains functions related to trace mode settings.

MARKER

The MARKER key contains functions related to markers.

PEAK SEARCH

The PEAK SEARCH key contains functions for searching for peaks and bottoms in

measured waveforms.

ANALYSIS

The ANALYSIS key contains functions related to measured waveform analysis.

FUNCTION

CENTER

SWEEP

SPAN

LEVEL

ZOOM

SETUP

MARKER

DISPLAY

PEAK

SEARCH

TRACE

ANALYSIS

USER

MEMORY

FILE

SYSTEM

ADVANCE

PROGRAM

OREMOTE

UNDO/

LOCAL

HELP

COPY

PRESET

4

IM AQ6373B-02EN

MEMORY

The MEMORY key contains functions for writing the contents of the active trace to the

unit’s internal memory. When you press the MEMORY key, the traces and memory list

screen (soft key menu) are displayed. A memory number may be entered in the DATA

ENTRY section, or selected using the rotary knob or arrow keys.

FILE

The FILE key contains functions for saving and loading waveform data, program data,

and the like to and from USB storage media (USB memory/HDD).

PROGRAM

The PROGRAM key contains the soft keys related to program functions for controlling

measurements through a program.

SYSTEM

The SYSTEM key contains system-related functions such as monochromator adjusting

optical alignment, wavelength adjustment, hardware setup, and setting initialization.

ADVANCE

The ADVANCE key contains functions for setting reference data used to make

comparison judgments on measured data and for logging analysis data.

USER

Frequently used soft keys can be registered on the soft key menu in the USER key.

Registering frequently used soft keys in the USER key allows you to execute frequently

used functions in a small number of steps.

COPY

The COPY key is used to output the measurement screen to a file.

When you press the COPY key, the measured waveforms and lists displayed on the

screen are output to the internal printer or a file.

PRESET

The PRESET key clears all internal settings of the AQ6373B except for the remote

interface (ETHERNET, GP-IB, and RS232) settings.

UNDO/LOCAL

The key's function changes depending on the status of the instrument when the UNDO/

LOCAL key is pressed. The following table shows the key's functions.

Status of Instrument Function

UNDO action is allowed If the UNDO key is pressed after changing parameter

settings, changing or deleting data, etc., the previous

action (change, deletion, etc.) is canceled and the state

preceding that action is restored.

During user key registration If the UNDO key is pressed during user key registration,

registration mode is canceled and the soft key menu

which appeared when the SYSTEM key was pressed is

displayed again.

During remote control by

external PC (Remote light is on)

Changes the state from the remote state back to the

local state. The remote light turns off.

HELP

When you press the HELP key, a soft key menu of the currently displayed screen is

displayed explanations.

Soft keys for selecting the “MORE INFO” which indicate additional information are

displayed by some soft keys in HELP screen.

3 Panel Keys and Knobs

La page est en cours de chargement...

YOKOGAWA AQ6373B-01 Getting Started Manual

Ce manuel convient également à

YOKOGAWA AQ6373B-01 Getting Started Manual

dans d''autres langues

Documents connexes

Autres documents