Hitachi RAC-35WSB Manuel utilisateur

– 1 –

ENGLISH

SPLIT TYPE AIR CONDITIONER

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAK-18PSB/RAC-18WSB

RAK-25PSB/RAC-25WSB

RAK-35PSB/RAC-35WSB

INDOOR UNIT OUTDOOR UNIT

RAK-18PSB

RAK-25PSB

RAK-35PSB

RAC-18WSB

RAC-25WSB

RAC-35WSB

This room air conditioner is only for consumer usage.

Do not use for preservation of foods, animals, plants, precision machines, art, medicine or such.

Instruction manual Page 1~20

To obtain the best performance and ensure years of

trouble free use, please read this instruction manual

completely.

Bedienungsanleitung Seite 21~40

Lesen Sie diese Bedienungsanleitung vollständig

durch, um eine optimale Geräteleistung und einen

langjährigen störungsfreien Betrieb sicherzustellen.

Mode d'emploi Pages 41~60

Pour obtenir une efficacité optimale et garantir la fiabilité

de fonctionnement de votre télécommande pendant

de nombreuses années, veuillez lire attentivement et

entièrement cette notice.

Manuale di istruzioni Pagina 61~80

Per ottenere il massimo delle prestazioni e garantire

un utilizzo sicuro per anni, leggere questo manuale di

istruzioni nella sua integrità.

Manual de instrucciones Página 81~100

Para obtener un rendimiento óptimo y asegurarse

muchos años de uso sin problemas, lea detenidamente

este manual de instrucciones.

Manual de instruções Página 101~120

Leia este manual de instruções na íntegra para obter

um desempenho ideal e garantir o funcionamento sem

problemas da unidade ao longo dos anos.

Οδηγίες χρήσης Σελίδα 121~140

Για να έχετε την καλύτερη δυνατή απόδοση και να

διασφαλίσετε πολυετή χρήση χωρίς προβλήματα,

διαβάστε ολόκληρο το παρόν εγχειρίδιο οδηγιών.

– 2 –

SAFETY PRECAUTION

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “ Warning” and “ Caution”. The “Warning” section contains matters which, if

not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs.)

Make sure to connect earth line. This sign in the figure indicates prohibition.

Indicates the instructions that must be followed.

• Please keep this manual after reading.

PRECAUTIONS DURING INSTALLATION

WARNING

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct the unit by

yourself.

PROHIBITION

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock or fire.

CONNECT EARTH LINE

• Be sure to use the specified piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

CAUTION

• A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

PROHIBITION

• Do not install the unit near a location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it.

• Please ensure smooth flow of water when installing the drain hose.

• Make sure that a single phase 220V-230V power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fire.

PROHIBITION

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

WARNING

• Should abnormal situation arise (like burning smell), please stop operating the

unit and turn off the circuit breaker. Contact your agent. Fault, short circuit or fire

may occur if you continue to operate the unit under abnormal situation.

• Please contact your agent for maintenance. Improper self maintenance may cause electric shock

and fire.

• Please contact your agent if you need to remove and reinstall the unit. Electric shock or fire may

occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING OPERATION

WARNING

• Avoid an extended period of direct airflow for your health.

PROHIBITION

• Do not put objects like thin rods into the panel of blower and suction side because

the high-speed fan inside may cause danger.

• Do not use any conductor as fuse wire, this could cause fatal accident.

PROHIBITION

• During thunder storm, disconnect and turn off the circuit breaker.

• Spray cans and other combustibles should not be located within a meter of the

air outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

PROHIBITION

“OFF”

PROHIBITION

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

CAUTION

• The product shall be operated under the manufacturer specification and not for

any other intended use.

PROHIBITION

DON'T WET

• Do not attempt to operate the unit with wet hands, this could cause fatal accident.

• When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insufficiency.

PROHIBITION

• Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

• Please ensure that outdoor mounting frame is always stable, firm and without

defect. If not, the outdoor unit may collapse and cause danger.

PROHIBITION

• Do not wash the unit with water or place a water container such as a vase on

the indoor unit.

Electrical leakage could be present and cause electric shock.

• Do not place plants directly under the airflow as it is bad for the plants.

PROHIBITION

• Be sure to stop the operation by using the remote controller and turn off the

circuit breaker during cleaning, the high-speed fan inside the unit may cause

danger.

• Turn off the circuit breaker if the unit is not be operated for a long period.

PROHIBITION

• Do not climb on the outdoor unit or put objects on it.

• When operating the unit with the door and windows opened, (the room humidity is

always above 80%) and with the air deflector facing down or moving automatically

for a long period of time, water will condense on the air deflector and drips down

occasionally. This will wet your furniture. Therefore, do not operate under such

condition for a long time.

PROHIBITION

• If the amount of heat in the room is above the cooling or heating capability of

the unit (for example: more people entering the room, using heating equipments

and etc.), the preset room temperature cannot be achieved.

• Indoor unit cleaning must be performed by authorized personnel only. Consult

your sales agent.

Using a commercially available detergent or similar can damage the plastic parts

or clog the drain pipe, causing water to drip with potential electric shock hazard.

PROHIBITION

DON'T TOUCH

• Do not touch the air outlet, bottom surface and aluminium fin of the outdoor

unit.

You may get hurt.

• Do not touch the refrigerant pipe and connecting valve.

Burns may result.

DON'T TOUCH

• This appliance is not intended for use by young children or infirm persons unless they have been

adequately supervised by a responsible person to ensure that they can use this appliance safely.

Young children should be supervised to ensure that they do not play with the appliance.

“OFF”

STRICTLY OBSERVE

PRECAUTIONS

– 4 –

NAMES AND FUNCTIONS OF EACH PART

(Understanding The Operating Mechanism, page 14)

Air Outlet

ECO Sensor

Front Panel

(Page 6)

Signal Receiver (internal)

Receive signal from the

remote controller.

Temporary Operation Switch

(Forced Cooling Switch)

Indicator

Horizontal/

Vertical Air Deflector

(internal)

Ion Mist Unit

Remote Controller

(Please refer to

Remote Controller

Manual)

Pipe/Wiring

Drain Hose

Drains dehumidified water generated from the indoor unit when in

the cooling, dehumidifying and dry cool modes.

Air Inlet (rear and left side)

Earth Terminal

(side bottom)

Drain Port (bottom)

Air Outlet

Discharges cool air when in heating

mode and warm air when in cooling

and dry cool modes, and warm or

cold air when in the dehumidifying

mode.

• While the power is on, a very small amount of power is

consumed within the control circuit even when the unit

is not in operation.

Power can be saved if the circuit breaker is switched off.

• Operation temperature of outdoor is -20°C to 43°C.

ABOUT OUTDOOR UNIT

• Even if the operation is stopped, the outdoor

unit fan continues to rotate for 10~60 seconds

to cool down the electrical parts.

• In heating operation, condensed water and

defrosted water is discharged from the outdoor

unit. Do not block the drain port as the water in

the drain may freeze in a cold area.

• Even during cooling operation, the water

condensed in the pipe, etc. may flow out from

the outdoor unit.

• When installing the outdoor unit under eaves,

etc. of the apartment, install a bush and drain

pipe on the drain port for drainage treatment.

CAUTION

Turn off the circuit breaker if the unit is not

in use for a long period.

INDOOR UNIT

OUTDOOR UNIT

– 5 –

ENGLISH

TEMPORARY SWITCH

Use this switch to start and stop when the

remote controller does not work.

• By pressing the temporary switch,the

operation is done in automatic mode.

• When the operation is done using the

temporary switch after the power source is

turned off and turn on again,the operation

is done in automatic mode.

• The air conditioner performs force-cooling

operation if the temporary switch is pressed

for about 5 seconds.

This operation is allowed to sales agents

only. Users must not perform this operation.

OPERATION LAMP (Yellow)

This lamp lights during operation.

The OPERATION LAMP flashes in

the following cases during heating.

(1) During preheating

For about 2-3 minutes after

starting up.

(2) During defrosting

Defrosting will be performed

about once an hour when frost

forms on the heat exchanger of

the outdoor unit, for 5-10 minutes

each time.

TIMER LAMP (Orange)

This lamp lights when the timer is

working.

CLEAN LAMP (Yellow)

ECO Sensor Lamp (Green)

Open the front panel to operate. (How to open the front panel, page 6)

Dust Catcher

Collects the dust swept by the

cleaning unit. (Page 12)

Micro mesh Stainless Filter (inside)

Collects particulates and dusts in the air. (Page 10)

Cleaning Unit

Cleans the dust caught by the

micro mesh stainless filter.

Dust Box

Collects and keeps the dust that

has been cleaned. (Page 9)

Air Purifying Filter Holder

INDOOR UNIT INDICATIONS

INDOOR UNIT CONTROL PANEL / CLEANING UNIT

– 6 –

INSTALLING ANTI-MOLD WASABI CASSETTE

1

Open the front panel.

2

Install the anti-mold wasabi cassette.

• Do not hold the movable panel when

opening and closing the front panel.

Front panel

Gripping part

• Hold and lift up the front panel.

• Push up the panel support until it

clicks to lock it.

Lower the front panel and fix in

position with the panel support.

Panel support

CAUTION

• Do not open the front panel during operation.

It may interrupt the movable panel to work properly.

Be sure to stop the operation first before opening

the front panel.

• Remove the dust box • Take out the anti-mold wasabi

cassette from the aluminium bag.

• Slide the anti-mold

wasabi cassette that

has been taken out of

the wrapper directly

into the Dust Box.

Do not remove or tear

the aluminium sheet on

the surface nor make a

hole on it.

Dust Box

Handle

Dust Box

Anti-mold wasabi

cassette

Aluminium bag

CAUTION

• Do not put your face close to the package when

you open it.

Your eyes or nose may be irritated by wasabi aroma.

• Do NOT eat.

No daily maintenance is required. However,

the effectiveness of anti-mold wasabi cassette

will be lost after approximately 10 years have

elapsed. Replace the anti-mold wasabi cassette

in such event.

– 7 –

ENGLISH

3

Close the front panel.

• Hold and lift up the front panel. • Push down the panel support until it clicks.

• Pull it downward.

Push the both ends of the front panel first and

then its center until it clicks.

CAUTION

• If the front panel is loose, it may come off and drop.

• When opening the front panel upwards, please do not use excessive force.

If the front panel comes off the device, this may cause it to malfunction.

• When the front panel remains open, be sure to push up the panel support.

– 8 –

FILTER CLEANING UNIT OPERATION CHECK

Performing operation check after the power is turned on.

Perform the filter cleaning unit operation check

• After the power is turned on (after the circuit breaker is switched on or power failure), the cleaning unit

makes one cycle of back and forth movement.

• At this time, the (CLEAN) indicator is lit.

• One cycle of operation check will take approximately 5 minutes.

• During the operation check, the unit performs “Fan” operation while the movable panel and horizontal air

deflector remain closed.

• If the (CLEAN) indicator blinks (lit for 4 seconds/off 1 second) after the operation check, refer to “Troubleshooting”

on page 16.

Dust catcher

Cleaning Unit

There is a filter cleaning wiper inside.

• The illustration shows the unit without front

panel for your reference only.

CAUTION

Do not put your fingers or a stick etc into the top surface during

the filter cleaning operation

It may result in injury or malfunction.

– 2 –

PREPARATION BEFORE OPERATION

■ To install the batteries

■ To ﬁ x the remote controller holder to the wall

1. Slide the cover to take it off.

2. Install two dry batteries AAA.LR03 (alkaline).

The direction of the batteries should match the

marks in the case.

3. Replace the cover at its original position.

1. Choose a place from where the signals can reach the unit.

2. Fix the remote controller holder to a wall, a pillar or similar

location with the provided screws.

3. Place the remote controller in the remote controller holder.

NOTE

Notes on batteries

● When replacing the batteries, use batteries of the same

type, and replace both old batteries together.

● When the system is not used for a long time, take the

batteries out.

● The batteries will last for approximately 1 year. However, if

the remote controller display begins to fade and degradation

of reception performance occurs within a year, replace both

batteries with new size AAA.LR03 (alkaline).

● The attached batteries are provided for the initial use of

the system.

The usable period of the batteries may be short depending

on the manufactured date of the air conditioner.

Notes on the remote controller

● Never expose the remote controller to direct sunlight.

● Dust on the signal transmitter or receiver will reduce the

sensitivity. Wipe off dust with soft cloth.

● Signal communication may be disabled if an electronic-

starter-type fluorescent lamp (such as inverter-type lamps)

is in the room. Consult the shop if that is the case.

● If the remote controller signals happen to operate another

appliance, move that appliance to somewhere else, or

consult the service shop.

● When the remote controller is not in use, please close the

slide cover to prevent failure.

Remote controller

Screws

Remote

controller holder

– 3 –

ENGLISH

PREPARATION BEFORE OPERATION

■ To set calendar and clock

1. Press (RESET) button when first time setting.

"Year" blinks.

2. Press (TIME) button to set the current year.

3. Press (CLOCK) button. "Day" and "Month"

blink.

4. Press (TIME) button to set the current day and

month.

5. Press (CLOCK) button. "CLOCK" blinks.

6. Press (TIME) button to set the clock to the current

time.

7. Press

(CLOCK) button.

Calendar and clock are set.

To modify the calendar and clock, press

(CLOCK)

button.

Then follow steps 1 to 7.

Calendar and clock need to be set again after changing

batteries.

After changing the batteries,

1. Press (RESET) button.

2. Direct remote controller towards indoor unit and press

(INFO) button.

3. The calendar and clock from indoor unit will be transmitted.

■ Calendar and clock will not be transmitted from indoor

unit when the following occurs:

● When there is a power failure.

● When breaker is OFF by user (unit is not in STANDBY

MODE).

NOTE

Note on setting the calendar and clock.

● If the calendar and clock are not set, the ON-timer, OFF-timer and Weekly Timer cannot be set.

● If the calendar and clock are not set correctly, the ON-timer, OFF-timer and Weekly Timer will not

operate correctly.

● When the ON-timer, OFF-timer and Weekly Timer are set, the calendar and clock cannot be changed.

If there is a need to change the calendar and clock, ON-timer, OFF-timer and Weekly Timer need to

be cancelled.

– 4 –

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

REMOTE CONTROLLER

● This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is

controlled electronically, the range of control may be shorter.

This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can

be controlled from the remote controller.

● Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission

capability.

● After new batteries are inserted into the remote controller, the unit will initially require approximately

10 seconds to respond to commands and operate.

● When remote controller is not in use for about 3 minutes during OFF condition, indicated by on the

display, the LCD will turn off.

● During clock setting, the LCD will turn off about 10 minutes later if the remote controller is not in use.

● When pressing any button, the LCD will turn on.

● The LCD will not turn off during TIMER setting.

Signal Transmitting/Receiving

Window

Point this window towards the

indoor unit when controlling it.

Sensor

A temperature sensor inside the

remote controller senses ambient

temperature around the remote-

controller.

Display

This indicates the room temperature

selected, current time, timer status,

function and airflow rate selected.

ROOM TEMPERATURE setting Buttons

Press these buttons to set the room

temperature.

Press the [ ] button to raise the room

temperature.

Press the [ ] button to lower the room

temperature.

Keep pressing and the value will change

more quickly.

ECO SENSOR Button

Use this button to set the ECO

SENSOR mode. ( p. 16)

START/STOP button

Press this button to start

operation. Press it again to stop

operation.

FAN SPEED selector Button

This determines the fan speed. Every

time you press this button, the airflow

rate will change from

(AUTO)

➞

(HIGH) ➞ (MED) ➞

(LOW) ➞ (SILENT) (This

button allows selection of optimal

or preferred fan speed for each

operation mode).

Transmission sign

The transmission sign lights up

when a signal is sent.

– 5 –

ENGLISH

MODE SELECTOR

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

AUTO

SILENT

LOW

MED

HIGH

START / STOP

ECO SENSOR

FAN

POWERFUL

Precautions for Use

●

Do not put the remote controller in the following places.

●

Under direct sunlight.

●

In the vicinity of a heater.

●

Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

●

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch

off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

●

If you press the MODE selector button during operation, the device may stop for about 3 minutes for

protection.

POWERFUL Button

Use this button to set the

POWERFUL mode. (

p. 18)

INFORMATION Button

(

p. 30)

ION MIST Button

(

p. 17)

ON / OFF TIMER setting Buttons

( p. 21)

WEEKLY TIMER setting Buttons

( p. 24)

MODE selector Button

Use this button to select the

operating mode. Every time you

press this button, the mode will

change from (AUTO) ➞

(HEAT) ➞ (DEHUMIDIFY) ➞

(COOL) ➞ (FAN) ➞

(ONE TOUCH CLEAN) and ➞

(FILTER CLEAN) cyclically.

(ONE TOUCH CLEAN) and

(FILTER CLEAN) can be

selected when the unit is OFF.

SILENT Button

Use this button to set the SILENT

mode. ( p. 19)

AUTO SWING (Vertical) Button

Controls the angle of the

horizontal air deflector. (

p. 14)

WIND MODE Button

Use this button to select the

operating mode. Every time you

press the button, the mode will

change from (AUTO SWING)

➞ CANCEL ➞

(DIRECT

AIRFLOW) ➞ (INDIRECT

AIRFLOW) ➞ CANCEL cyclically.

( p. 14)

LEAVE HOME Button

( p. 20)

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

ECO SLEEP TIMER Button

Use this button to set the ECO

sleep timer. ( p. 22)

SILENT

INFO

SLEEP TIMER

AUTO SWING (VERTICAL)

AUTO SWING (HORIZONTAL)

LEAVE HOME

CLEAN

FILTER CLEAN

ION MIST

DIRECT AIRFLOW

INDIRECT AIRFLOW

DAY

PROGRAM NO.

ON / OFF TIMER

TIME

OK

DELETE

COPY / PASTE

CANCEL

SEND

CLOCK

– 6 –

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT or COOL depending on the current

room temperature. The selected mode of operation will change when the room temperature varies.

VARIOUS FUNCTIONS

■ Auto Restart Control

● If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation

mode and airflow direction.

(As the operation is not stopped by remote controller.)

● If you intend not to continue the operation when the power is resumed, switch off the power supply.

When you switch on the circuit breaker, the operation will be automatically restarted with previous operation mode

and airflow direction.

Note: 1. If you do not require Auto Restart Control, please consult your sales agent.

2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.

■ As the settings are stored in the memory of the remote controller, you

only have to press the

(START/STOP) button next time.

Press the MODE selector button so that the display indicates the

(AUTO) mode of operation.

● When AUTO has been selected, the device will automatically

determine the mode of operation, HEAT or COOL depending on

the current room temperature. However the mode of operation will

not change when indoor unit is connected to multi type outdoor

unit.

● If the mode automatically selected by the unit is not satisfactory,

manually change the mode setting (HEAT, DEHUMIDIFY, COOL

or FAN).

Press the (FAN SPEED) button to select AUTO, HIGH, MED, LOW

or SILENT.

Press the (START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

START

STOP

1

2

3

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

– 7 –

ENGLISH

HEATING OPERATION

● Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

● In order to maintain reliability of the device, please use this device when outdoor temperature is above

–20°C.

Press the MODE selector button so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may

vary depending on conditions.

Press the (START/STOP) button. Heating operation starts with

a beep. Press the button again to stop operation.

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting temperature

is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy heating.

START

STOP

Defrosting will be performed about once an hour when frost forms on the heat exchange of the outdoor unit,

for 5~10 minutes each time.

During defrosting operation, the operation lamp blinks in a cycle of 3 seconds on and 0.5 second off.

The maximum time for defrosting is 20 minutes.

1

2

3

Defrosting

– 8 –

DEHUMIDIFYING OPERATION

■ Dehumidifying Function

● When the room temperature is higher than the temperature setting: The device will dehumidify the room,

reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the

temperature setting slightly lower than the current room temperature, regardless of the temperature setting.

● The preset room temperature may not be reached depending on the number of people present in the room

or other room conditions.

Set the desired room temperature with the ROOM

TEMPERATURE setting buttons (the display indicates the

setting).

The range of 20-26˚C is recommended as the room

temperature for dehumidifying.

Press the (START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

START

STOP

Press the MODE selector button so that the display

indicates (DEHUMIDIFY).

The fan speed is set at LOW.

Press (FAN SPEED) button to select SILENT or LOW fan

speed.

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

1

2

– 9 –

ENGLISH

COOLING OPERATION

Use the device for cooling when the outdoor temperature is -10~ 43°C.

If indoors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the MODE selector button so that the display indicates

(COOL).

■ As the settings are stored in the memory of the remote controller, you

only have to press the (START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting tem-

perature is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy cooling.

START

STOP

1

2

3

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO) (HIGH) (MED)

(SILENT) (LOW)

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Press the (START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the (OPERATION) lamp lights).

The cooling function will start as soon as user set the temperature

below the current room temperature.

– 10 –

FAN OPERATION

User can use the device simply as an air circulator.

START

STOP

1

2

Press the MODE selector so that the display indicates

(FAN).

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(HIGH) (MED) (LOW) (SILENT)

Press the (START/STOP) button. Fan operation starts with

a beep. Press the button again to stop operation.

– 11 –

ENGLISH

CLEAN (ONE TOUCH CLEAN) OPERATION

● Drying indoor heat exchanger after cooling operation to prevent mildew.

● Press the (MODE) button to display “ ” (CLEAN)

during OFF mode.

Press the (START/STOP) button.

ONE TOUCH CLEAN operation starts with a beep.

● When the ONE TOUCH CLEAN operation completes,

unit will switch OFF automatically.

● Total time taken for ONE TOUCH CLEAN operation is

60 minutes.

● During this operation, HEATING/FAN operation will

operate.

● During ONE TOUCH CLEAN, operation lamp and clean

lamp light up.

“ ” and “ ” are displayed on the LCD.

Press the button again to stop the operation.

Ion Mist

Wind Mode

NOTE

● Once if the weekly timer is set then there is no need to cancel it before operating ONE TOUCH CLEAN.

START

STOP

1

– 12 –

FILTER CLEANING OPERATION (AUTOMATIC OPERATION)

■ To stop AUTOMATIC FILTER CLEANING operation

● Automatic filter cleaning mode is set at the time of purchase.

● Automatically cleans the micro mesh stainless filter when the basic air-conditioning operation (AUTO,

HEATING, DEHUMIDIFYING or COOLING) has ended.

• The cleaning unit makes cycle to back and forth movement to sweep the dust on the micro mesh

stainless filter and the dust catcher puts the collected dust into the dust box.

• One cycle of filter cleaning operation will take approximately 5 minutes.

Conditions of the automatic filter cleaning.

• When the air conditioner operates for more than 15 minutes and stops, automatic filter cleaning is

performed in one of the following conditions.

(1) Accumulated operating hours of the air conditioner have exceeded 8 hours.

(2) Air conditioner is not operated for more than one week.

(To clean the dust which is naturally deposited on the top filter.)

CAUTION: The accumulated operating hours will not be reset if the automatic filter cleaning operation

is stopped before its completion.

• If the air conditioner is in operation continuously for 24 hours, the operation is stopped and automatic

filter cleaning operation is performed.

After the completion of automatic filter cleaning, the operation will return to previous mode.

● Automatic filter cleaning is not performed if the air conditioner operation is stopped by sleep timer or

off timer function.

If you use sleep timer or off timer every time, it is recommended to operate manual filter cleaning once

every 2~3 days.

However, if manual filter cleaning is not performed, automatic filter cleaning will be performed approximately

once a week after the air conditioner operation is stopped by sleep timer or off timer to protect the device.

Press the (START/STOP) button.

STOP

● Use the remote controller to run filter cleaning operation when the air conditioner operation is stopped.

● If the air conditioner is not in use for a long period, it is recommended to manually run filter cleaning before

using the air conditioner.

Press the (MODE) select button so that the display

indicates (FILTER CLEANING) when the unit is OFF.

Press the (START/STOP) button.

FILTER CLEANING operation starts with a beep.

• The cleaning unit makes one cycle of back and forth movement

to sweep the dust on the micro mesh stainless filter and the

dust catcher puts the collected dust in to the dust box.

• One cycle of filter cleaning operation will take approximately

5 minutes.

Press the button again to stop the filter cleaning operation.

FILTER CLEANING OPERATION (MANUAL OPERATION)

Ion Mist

Wind Mode

1

START

STOP

– 13 –

ENGLISH

HOW TO PROHIBIT THE FILTER CLEANING OPERATION

• With the remote controller, you can deactivate the filter cleaning operation.

• This setting should be made only when the air conditioner is stopped.

Press the (AUTO SWING VERTICAL) and (OK) buttons

simultaneously for 5 seconds.

A double short beep sounds is emitted and the filter cleaning is

deactivated.

To reactivate the filter cleaning, press the (AUTO SWING

VERTICAL) and (OK) buttons simultaneously for 5 seconds,

a single short beep sound is emitted and the setting returns the

filter cleaning operation.

Ion Mist

Wind Mode

Filter cleaning operation (Default)

(at the time of purchase)

“Beep” sound

Filter cleaning operation

is prohibited

“Beep Beep” sound

1

FILTER CLEANING OPERATION (MANUAL OPERATION)

NOTE

About the noise during filter cleaning

• A whirring motor noise is generated due to driving of the cleaning unit.

• A clapping noise is generated when the dust catcher collects the dust swept by the cleaning unit.

• A clapping noise is generated when the dust catcher is turned over by the cleaning unit.

• A sweeping sound is generated when the cleaning unit sweeps the dust.

Maintenance

• No daily maintenance is required. However, dust amount varies depending on the environment in

which the air conditioner is used. Check the dust amount in the Dust Box approximately once every

two years and throw the dust, if any.

• Greasy dirt can also be cleaned by the combined function of filter cleaning and the micro mesh

stainless filter. If the dirt looks heavy,remove the micro mesh stainless filter, the dust catcher and

the filter cleaning wiper to wash them with water.

CAUTION

Do not put your fingers or a stick etc into the top part of the indoor unit during filter cleaning operation.

It may result in injury or malfunction.

La page charge ...

Hitachi RAC-35WSB Manuel utilisateur

Ce manuel convient également à

Hitachi RAC-35WSB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents