Simplicity 030243-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030243-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

AC Generator

5600 Watt

Model No.

580.675610

Part No. 200656GS Draft A (10/04/2006)

Generator

Customer Helpline

1-800-222-3136

Operator’s Manual

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

Sears Canada, Inc.

Visit our Craftsman website: www.sears.ca

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Français, p. 36

AVERTISSEMENT

Avant d’utiliser ce produit, veuillez lire le

manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

WARNING

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

TABLE OF CONTENTS

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

FEATURES AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . 6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SCHEMATIC/WIRING DIAGRAM. . . . . . . . . . . . . . . . . . 22-23

REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . 24-33

EMISSIONS SYSTEM WARRANTY . . . . . . . . . . . . . . . . 34-35

FRANÇAIS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-59

HOW TO ORDER PARTS . . . . . . . . . . . . . . . . . . . BACK PAGE

ONE-YEAR FULL WARRANTY ON CRAFTSMAN GENERATOR

If this generator fails due to a defect in material or workmanship within one year from the date of purchase, return it to any

Sears store, other Craftsman outlet, or Sears Parts & Repair Center in the United States or Canada for free repair (or

replacement if repair proves impossible).

Additional One-Year Limited Warranty on Craftsman Generator

For the second year from the date of purchase, if any part of this generator fails due to a defect in material or workmanship, a

new part will be supplied free of charge. You must pay the labor cost if you wish to have it installed.

All warranty coverage applies for only 90 days from date of purchase if this generator is ever used for commercial or rental

purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

WARRANTY

SAFETY RULES

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations, and any hazards involved.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

Hazard Symbols and Meanings

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property damage.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Hazardous Chemical

Operator’s Manual

DANGER

Contents are harmful or fatal if swallowed. Avoid

contact to eyes, skin or clothing. DO NOT take

internally. Avoid breathing the mist or vapor.

Overexposure to eyes or skin can cause irritation.

Keep stabilizer out of the reach of children.

Fuel stabilizer is a hazardous chemical.**

• Fresh Start™ fuel cap is designed to hold a cartridge which

contains fuel stabilizer.

• If SWALLOWED, call physician immediately. DO NOT induce

vomiting. If inhaled, remove to fresh air. In case of eye or skin

contact, flush with water for 15 minutes.

• Store unopened cartridges in a cool, dry, well ventilated area.

Keep open cartridge in fuel cap, and fuel cap closed on fuel

tank when not in use.

• In the case of an emergency, contact a physician immediately

and call 1-800-424-9300 for material safety information.

**Fuel stabilizer contains: 2,6-di-tret-butylphenol (128-39-2) and aliphatic petroleum

distillate (64742-47-8).

WARNING

Running engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open, including the generator

compartment of a recreational vehicle (RV).

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT choke carburetor to stop engine.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

WARNING

Generator produces powerful voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground circuit fault interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

generator including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

• NEVER operate generator without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

NOTICE

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected to it.

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

CAUTION

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

NOTICE

Improper treatment of generator can damage it and

shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

Sears.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

• This equipment is designed to be used with Sears authorized

parts ONLY. If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

KNOW YOUR GENERATOR

Read the Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

FEATURES AND CONTROLS

Stat Station™

120 Volt AC, 20 Amp, Duplex Receptacles — May be used

to supply electrical power for the operation of 120 Volt AC,

20 Amp, single phase, 60 Hz electrical, lighting, appliance,

tool and motor loads.

120/240 Volt AC, 30 Amp Locking Receptacle — May be

used to supply electrical power for the operation of

120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical, lighting, appliance, tool and motor loads.

Air Cleaner — Protects engine by filtering dust and debris

out of intake air.

Choke Lever — Used when starting a cold engine.

Data Tag — Provides model, revision and serial number of

generator. Please have these readily available when calling

for assistance.

Double Pole Circuit Breaker (AC) — A double pole circuit

breaker is provided to protect all the receptacles and

generator against electrical overload.

Fuel Tank — Capacity of five (5) U.S. gallons.

Fuel Valve — Used to turn fuel supply on and off to engine.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Oil Fill Cap — Check and fill engine with oil here. See page

16 for oil recommendations and filling instructions.

On/Off Switch — Set this switch to "On" before using recoil

starter. Set switch to "Off" to switch off engine.

Recoil Starter — Used to start the engine.

Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

StatStation™ — Displays the electrical load on generator

based on output frequency. It also has a built in maintenance

reminder.

120 Volt AC, 20 Amp

Duplex Receptacles

Fuel Tank

Choke Lever

Recoil Starter

On/Off Switch

Double Pole Circuit

Breaker (AC)

120/240 Volt AC,

30 Amp Receptacle

Spark Arrester Muffler

Air Cleaner

Grounding Fastener

Oil Fill Cap

Data Tag

Fuel Valve

Your Craftsman generator requires some assembly and is

ready for use only after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-222-3136.

Unpacking the Generator

1. Set the carton on a rigid flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from top

to bottom.

4. Leave generator on carton to install wheel kit.

Carton Contents

Check all contents against those listed below:

• Main unit

• Engine oil

• Operator’s manual

• Wheel kit

• Adapter cord set

If any parts are missing or damaged, call the generator

helpline at 1-800-222-3136.

Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use. DO

NOT tow this unit with a motorized vehicle.

You will need the following tools to install these components:

• 13mm wrenches

• Socket wrench with a 13mm socket

• Pliers

• Safety glasses

Install the Wheel Kit as Follows:

IMPORTANT: Installing the wheel kit must be completed

prior to adding any oil or fuel.

1. Tip generator so that engine end is up.

2. Slide axle through both mounting brackets.

3. Place a wheel on each side as shown in A.

4. Place a washer on axle and then place an e-ring in axle

groove.

5. Install e-ring with pliers, squeezing from top of e-ring to

bottom of axle.

6. Repeat step 4 and 5 to secure second wheel.

7. Tip generator so that engine side is down.

8. Line up holes in support leg with holes in generator

frame.

9. Attach support leg using 2 capscrews (M8 x 16 mm) and

2 hex nuts. Tighten with a 13mm socket wrench and

13mm wrench.

10. Return generator to normal operating position (resting

on wheels and support leg).

ASSEMBLY

Support Leg

Axle

Flat Washer

Wheel

E-Ring

Axle

Wheel

Hex Nut

Capscrew

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne

when installing or removing.

• Always wear eye protection when installing/removing e-rings.

BEFORE STARTING THE GENERATOR

Add Engine Oil

CAUTION! Any attempt to crank or start the engine before it

has been properly serviced with the recommended oil may

result in an engine failure.

1. Place generator on a level surface.

2. Clean area around oil fill and remove yellow oil fill cap.

NOTE: See “Oil Recommendations” in Maintenance section.

Verify provided oil bottle is the correct viscosity for current

ambient temperature.

3. Using oil funnel (optional), slowly pour entire contents

of provided oil bottle (26 oz.) into oil fill opening.

4. Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see “High Altitude”.

• Gasoline with up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful

not to overfill. Allow at least 1.5" of tank space for fuel

expansion, as shown here.

3. Install fuel cap and wait for any spilled fuel to evaporate.

CAUTION! Alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine performance issues, the fuel system should

be treated with a fuel preserver or emptied before storage of

30 days or longer. To protect the fuel system from gum

formation, use Briggs & Stratton FRESH START™ fuel

stabilizer plus, or FRESH START™ continuous fuel preserver

(concentrated liquid cartridge). If fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Use fresh fuel next season.

See “Storage” for additional information.

NEVER use engine or carburetor cleaner products in the fuel

tank as permanent damage may occur.

Fuel

Tank

1.5” Air Space

NOTICE

Improper treatment of generator can damage it and

shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in

an engine failure.

NOTICE

Avoid generator damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• DO NOT light a cigarette or smoke.

Fresh Start™ Fuel Cap

Adding fuel preserver helps keep fuel fresh and carburetors

clean for easier starting, all season long. This new fuel cap

automatically drips concentrated fuel preserver into your fuel

tank.

1. Place cartridge into fuel cap.

2. Push to “snap” cartridge into place.

3. Remove tab to expose membrane.

IMPORTANT: DO NOT remove the silver foil seal on the

opposite side of the cartridge.

4. Reinstall fuel cap on fuel tank.

5. Periodically check the cartridge to ensure there is still

fuel stabilizer inside. If it is empty, remove cartridge and

replace.

High-altitude use

At higher altitudes (over 5,000 feet), 85 octane/85 AKI

(89 RON) gasoline is recommended. High-altitude use may

require a carburetor jet kit to improve performance and

decrease fuel consumption. See any Sears or qualified dealer

for more information.

DANGER

Contents are harmful or fatal if swallowed. Avoid

contact to eyes, skin or clothing. DO NOT take

internally. Avoid breathing the mist or vapor.

Overexposure to eyes or skin can cause irritation.

Keep stabilizer out of the reach of children.

Fuel stabilizer is a hazardous chemical.**

• If SWALLOWED, call physician immediately.

• In the case of an emergency, contact a physician immediately

and call 1-800-424-9300 for material safety information.

**Fuel stabilizer contains: 2,6-di-tret-butylphenol (128-39-2) and aliphatic petroleum

distillate (64742-47-8).

HOW TO USE YOUR GENERATOR

If you have any problems operating your generator after

reading the manual, please call the generator helpline at

1-800-222-3136.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on the

AC output receptacles. The system ground is connected to

the AC neutral wire (the neutral is bonded to the generator

frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction.

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there may

be additional regulations which must be observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician. The

connection must isolate the generator power from utility

power, and must comply with all applicable laws and

electrical codes.

Generator Location

Generator Clearance

Place generator outdoors in an area that will not accumulate

deadly exhaust gas. DO NOT place generator where exhaust

gas could accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is kept

away from any windows, doors, ventilation intakes or other

openings that can allow exhaust gas to collect in a confined

area. Prevailing winds and air currents should be taken into

consideration when positioning generator.

OPERATION

Exhaust Port

Typical Generator Shown

WARNING

Generator produces powerful voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground circuit fault interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (1.5 m) clearance on all sides of generator

including overhead.

WARNING

Running engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open, including the generator

compartment of a recreational vehicle (RV).

To Start The Engine

Disconnect all electrical loads from the generator. NEVER

start or stop engine with electrical devices plugged in and

turned ON. Follow start instruction steps in numerical order:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn red fuel valve to “On” position.

3. Place choke lever in “Choke” position.

4. Set On/Off switch to “On” position.

5. Grasp recoil handle and pull slowly until slight resistance

is felt. Then pull rapidly to start engine.

IMPORTANT: If engine floods, place choke lever in “Run”

position and crank until engine starts.

6. Move choke lever to “Run” position a short distance at a

time over several seconds in warm weather or minutes

in cold weather. Let engine run smoothly before each

change. Operate with choke in “Run” position.

NOTE: If engine starts after 3 pulls but fails to run, or if unit

shuts down during operation, make sure unit is on a level

surface and check for proper oil level in crankcase. This unit

may be equipped with a low oil protection device. If so, oil

must be at proper level for engine to start.

Connecting Electrical Loads

• Let the engine stabilize and warm up for a few minutes

after starting.

• DO NOT connect 240 Volt loads to 120 Volt receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• Plug in and turn on the desired 120 Volt AC, single phase,

60 Hertz electrical loads.

• DO NOT OVERLOAD THE GENERATOR. See “Don’t

Overload Generator”.

Stopping the Engine

1. Turn off and unplug all electrical loads from unit. NEVER

start or stop engine with electrical devices plugged in

and turned on.

2. Let engine run at no-load for two minutes to stabilize

unit’s internal temperatures.

3. Move On/Off switch to “Off” position.

4. Move fuel valve to “Off” position.

On/Off Switch is shown

in On position

“Off”

Position

“On”

Position

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

generator including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

NOTICE

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected to it.

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

WARNING

Backfire, fire or engine damage could occur.

• DO NOT stop engine by moving choke lever to “Choke”

position.

CORD SETS AND RECEPTACLES

Use only high quality, well-insulated, grounded extension

cords with the generator’s 120 Volt electrical receptacles.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use them.

Extension cord sets used should be rated for 125 Volt AC

loads at 20 Amps or greater for most electrical devices.

Some devices, however, may not require this type of

extension cord. Check the operator’s manuals of those

devices for the manufacturer’s recommendations.

Keep extension cords as short as possible, preferably less

than 15 feet long, to prevent voltage drop and possible

overheating of wires.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater). You can use the same 4–wire cord if you plan to

run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single phase

loads requiring up to 5,600 watts of power (5.6 kW) at

23.3 Amps for 240 Volts or two independent 120 Volt loads

at 23.3 Amps each. The outlet is protected by a double pole

rocker switch circuit breaker.

120 Volt AC, 20 Amp, Duplex Receptacles

Each duplex receptacle is protected against overload by a

double pole rocker switch circuit breaker.

Use each receptacle to operate 120 Volt AC, single–phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW) at

20 Amps of current. Use cord sets that are rated for 125 Volt

AC loads at 20 Amps (or greater). Inspect cord sets before

each use.

GENERATOR ADAPTER CORD SET

The generator comes with a 25’ generator adapter cord set

designed to provide two sets of 120 Volt, 20 Amp outlets

from one 120 Volt, 20 Amp duplex receptacle.

The maximum load on each outlet is 20 Amps. The maximum

total load on both black wire outlets or white stripe wire outlets

is 20 Amps. If an extension cord is used with adapter cord set,

be sure extension cord is rated for 125V at 20 Amps.

NOTE: Follow all safety precautions when connecting any

extension cord or device to the generator.

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

NOTICE

Receptacles may be marked with rating value greater than

generator output capacity.

• NEVER attempt to power a device requiring more amperage

than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

WARNING

Overloaded electrical cords can overheat, arc, and

burn resulting in death, bodily injury, and/or

property damage.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

DON’T OVERLOAD GENERATOR

Capacity

You must make sure your generator can supply enough rated

(running) and surge (starting) watts for the items you will

power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is the

amount of power your generator must produce to keep

your items running.

3. Estimate how many surge (starting) watts you will need.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

NOTE: The rated (running) watts cannot exceed 5600. Also,

given the 5600 watt rated limit, additional surge (starting)

watts cannot exceed 8600.

Power Management

To prolong the life of your generator and attached devices, it

is important to take care when adding electrical loads to your

generator. There should be nothing connected to the

generator outlets before starting it's engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity, as

described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated

(Running) Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200

1800

Refrigerator

800

1600

Deep Freezer

500

Television

500

Light (75 Watts)

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

Coffee Maker

1500

Electric Stove - Single Element

1500

Hot Plate

2500

Family Room

DVD/CD Player

100

VCR

100

Stereo Receiver

450

Color Television - 27”

500

Personal Computer w/17”

monitor

800

Other

Security System

180

AM/FM Clock Radio

300

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40

Gallon

4000

DIY/Job Site

Quartz Halogen Work Light

1000

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

ENGINE TECHNICAL INFORMATION

This is a single cylinder, overhead valve(OHV), air cooled

engine. It is a low emissions engine.

In the State of California, Model Series 200000 engines are

certified by the California Air Resources Board to meet

emissions standards for 250 hours. Such certification does

not grant the purchaser, owner or operator of this engine any

additional warranties with respect to the performance or

operational life of this engine. The engine is warranted solely

according to the product and emissions warranties stated

elsewhere in this manual.

Power Ratings

* The gross power rating for individual gas engine models is

labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been

obtained and corrected in accordance with SAE J1995

(Revision 2002-05). Actual gross engine power will be lower

and is affected by, among other things, ambient operating

conditions and engine-to-engine variability. Given both the

wide array of products on which engines are placed and the

variety of environmental issues applicable to operating the

equipment, the gas engine will not develop the rated gross

power when used in a given piece of power equipment

(actual "on-site" or net horsepower). This difference is due to

a variety of factors including, but not limited to, accessories

(air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating

conditions (temperature, humidity, altitude), and engine-to-

engine variability. Due to manufacturing and capacity

limitations, Briggs & Stratton may substitute an engine of

higher rated power for this Series engine.

PRODUCT SPECIFICATIONS

Generator Specifications

Starting Wattage . . . . . . . . . . . . . . . . . . . . 8600 Watts (8.6 kW)

Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . 5600 Watts (5.6 kW)

AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240 Volts

AC Current

at 240 Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.3 Amps

at 120 Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46.6 Amps

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz at 3600 rpm

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Phase

Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 U.S. gallons

Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 lbs.

Engine Specifications

Gross* Horsepower . . . . . . . . . . . . . . . . . . . . . 10 at 3600 rpm

Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12 in. (79 mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.44 in. (62 mm)

Displacement . . . . . . . . . . . . . . . . . . . . . . . . 18.64 in. (305 cc)

Spark Plug

Type: . . . . . . . . . . . . Briggs & Stratton

491055S or 5066D

Set Gap To: . . . . . . . . . . . . . . . . . . . . 0.030 inch (0.76 mm)

Armature Air Gap: . . . . . . . . . . 0.008-0.012 in. (0.20-0.30 mm)

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . . . 0.004-0.006 in. (0.10-0.15 mm)

Exhaust . . . . . . . . . . . . . . . . . . 0.004-0.006 in. (0.10-0.15 mm)

Oil Capacity . . . . . . . . . . . . . . . . . . . .28 Ounces (0.8 Liters)

NOTE: For practical operation, the generator load should not

exceed 85% of rated wattage. Engine gross horsepower will

decrease 3-1/2% for each 1,000 feet (300 meters) above sea

level and 1% for each 10° F (5.6° C) above 77° F (25° C). It

should operate satisfactorily at an angle up to 15°.

SPECIFICATIONS

MAINTENANCE SCHEDULE

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

MAINTENANCE

Change oil after the first (5) operating hours and every 50 hours or every year, whichever occurs first, thereafter.

Change sooner when operating under dirty or dusty conditions.

Replace more often under dirty or dusty conditions.

GENERAL RECOMMENDATIONS

Regular maintenance will improve the performance and

extend the life of the generator. See any Sears or other

qualified dealer for service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain

generator as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least once

each season. Follow the requirements in the “Maintenance

Schedule” chart above.

NOTE: Once a year you should clean or replace the spark

plug and replace the air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

EMISSIONS CONTROL

Maintenance, replacement or repair of the emissions control

devices and systems may be performed by any non-road

engine repair establishment or individual.

GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and

dry. Operate and store the unit in a clean dry environment

where it will not be exposed to excessive dust, dirt, moisture

or any corrosive vapors. Cooling air slots in the generator

must not become clogged with snow, leaves, or any other

foreign material.

Check the cleanliness of the generator frequently and clean

when dust, dirt, oil, moisture or other foreign substances are

visible on its exterior surface.

NOTE: DO NOT use a garden hose to clean generator. Water

can enter the engine fuel system and cause problems. In

addition, if water enters the generator through cooling air

slots, some of the water will be retained in voids and cracks

of the rotor and stator winding insulation. Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Generator Cleaning

Daily or before use, clean accumulated debris from

generator. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the generator.

These openings must be kept clean and unobstructed.

Generator parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

MAINTENANCE SCHEDULE OPERATING INTERVALS

SERVICE DATES

FILL IN DATES AS YOU COMPLETE

REGULAR SERVICE

MAINTENANCE TASK

Before

Each Use

Every 25 Hours or

Yearly

Every 50 Hours or

Yearly

Every 100 Hours

or Yearly

Check oil level

Clean debris

Change engine oil

Service air cleaner

Service spark plug

Service spark arrester

Clean cooling system

Check valve clearance

Prepare for storage If unit is to remain idle for longer than 30 days.

NOTICE

Improper treatment of generator can damage it and

shorten its life.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

StatStation™

The StatStation™ displays the nominal load on generator

based on output frequency. It also has a built in maintenance

reminder.

Wattage Monitor

The LED display will indicate 0-95% nominal load.The display

will flash at 90% nominal load and above. If above 95%

nominal load the display will flash “OL” (meaning ‘overload’).

When load returns to within normal range, the display will

automatically resume nominal load indication. See the table

below for operation functions.

Maintenance Reminder

The LED will display certain codes to alert you to check oil,

change oil, check or replace air filter and check or replace

spark plug. The following codes will display:

“C1” Check oil at 8 hour increments

“C2” Change oil at 50 hour increments

“C3” Check or replace air filter at 25 hour increments

“C4” Check or replace spark plug at 100 hour increments

Pushing “Reset” will set the indicated code timer to zero.

If nominal load and maintenance codes appear

simultaneously, the LED shall display, alternately, the

nominal load and code as follows:

The code will display for 3 seconds, then 1/2 second off. The

load will display for 6 seconds and then 1/2 second off.

ENGINE MAINTENANCE

Oil

Oil Recommendations

NOTE: Use a high quality detergent oil classified “For Service

SF, SG, SH, SJ” or higher. DO NOT use special additives.

1. Choose a viscosity according to the table below:

NOTE: Synthetic oil meeting ILSAC GF-2, API certification

mark and API service symbol with “SJ/CF ENERGY

CONSERVING” or higher, is an acceptable oil at all

temperatures. Use of synthetic oil does not alter required oil

change intervals.

SAE 30: 40°F and higher (5°C and higher) is good for all

purpose use above 40°F, use below 40°F will cause hard

starting.

10W-30: 0 to 100°F (-18 to 38°C) is better for varying

temperature conditions. This viscosity improves cold weather

starting, but may increase oil consumption above 80°F

(27°C).

*Check oil level frequently at higher temperatures.

Synthetic 5W-30: -20 to 120°F (-30 to 40 °C) provides the

best protection at all temperatures as well as improved

starting with less oil consumption.

5W-30: 40°F and below (5°C and below) is recommended for

winter use and works best in cold conditions.

Frequency Range LED Display

62.5-62.0 0

61.9-61.5 0

61.4-61.0 10

60.9-60.5 20

60.4-60.0 40

59.9-59.5 60

59.4-59.0 70

58.9-58.5 80

58.4-58.0 Flash 90

57.9-57.5 Flash 95

57.4-57.0 Flash OL

57.0 and below Flash OL

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Checking Oil Level

Oil level should be checked prior to each use or at least every

5 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Clean area around oil fill and remove oil fill cap.

3. Verify oil is at the point of overflowing at oil fill opening.

4. Replace and tighten oil fill cap.

Adding Engine Oil

1. Make sure generator is on a level surface.

2. Check oil level as described in “Checking Oil Level”.

3. If needed, slowly pour oil into oil fill opening to the point

of overflowing at oil fill.

4. Replace and tighten oil fill cap.

Service Air Cleaner

Your engine will not run properly and may be damaged if you

run it with a dirty air cleaner.

Replace the air cleaner every 25 hours of operation or once

each year, whichever comes first. Replace more often if

operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screws and remove air cleaner cover. Remove

paper filter.

2. Install clean (or new) air cleaner assembly inside cover.

Dispose of old filter properly.

3. Assemble air cleaner cover onto base and tighten

screws.

NOTE: You can purchase new air cleaner elements by calling

1-800-4-MY-HOME (469-4663).

Changing Engine Oil

Change the oil after the first 5 hours of operation. Change oil

every 50 hours thereafter. If you are using your generator

under extremely dirty or dusty conditions, or in extremely hot

weather, change the oil more often.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change the oil while the engine is still warm from running, as

follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

3. Clean area around oil drain plug. The oil drain plug is

located at base of engine, opposite carburetor.

4. Remove oil drain plug and drain oil completely into a

suitable container.

5. Reinstall oil drain plug and tighten securely. Remove oil

fill cap.

6. Slowly pour recommended oil (about 28 oz.) into oil fill

opening to the point of overflowing at oil fill cap.

7. Reinstall oil fill cap. Finger tighten cap securely.

8. Wipe up any spilled oil.

9. Reconnect spark plug wire to spark plug.

Clean/Replace Spark Plug

Change the spark plug every 100 hours of operation or once

each year, whichever comes first. This will help your engine

to start easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use a recommended replacement

plug.

4. Check electrode gap with wire feeler gauge and set spark

plug gap to 0.030 inch (0.76mm) if necessary.

5. Install spark plug and tighten firmly.

NOTE: You can purchase a new spark plug by calling

1-800-4-MY-HOME (469-4663).

Cartridge

Screw

Cover

Base

CAUTION

Avoid prolonged or repeated skin contact with used motor

oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Clean Spark Arrester Screen

The engine exhaust muffler has a spark arrester screen.

Inspect and clean the screen every 100 hours of operation or

once each year, whichever comes first.

NOTE: You can purchase a new spark arrester screen by

calling 1-800-4-MY-HOME (469-4663).

If you use your generator on any forest-covered, brush-

covered, or grass-covered unimproved land, it must have a

spark arrester. The spark arrester must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrester as follows:

1. To remove muffler heat shield from muffler, remove four

screws that connect guard to muffler bracket.

2. Remove four screws that attach spark arrester screen.

3. Inspect screen and replace if torn, perforated or

otherwise damaged. DO NOT use a defective screen. If

screen is not damaged, clean it with commercial solvent.

4. Reattach screen and muffler guard.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason, we recommend you have a Sears or other

qualified service dealer clean the cooling system per

recommended intervals (see “Maintenance Schedule” on

page 15). Equally important is to keep top of engine free

from debris. See “Generator Cleaning”.

Check Valve Clearance

Regular valve clearance check and adjustment will improve

performance and extend engine life. This procedure cannot

be done without partial engine disassembly and the use of

special tools. For this reason we recommend that you have a

Sears or other qualified service dealer check and adjust valve

clearance at recommended intervals.

Carburetor Adjustment

The carburetor on this engine is low emission. It is equipped

with a non-adjustable idle mixture valve and governed idle, if

equipped. Governed idle and top speed have been set at the

factory. If adjustment is required, see a Sears or other

qualified service dealer.

Muffler

Spark Arrester

Screen

Heat Shield

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

CAUTION

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

STORAGE

GENERAL

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot be

done and you must store the unit for more than 30 days, use

the following information as a guide to prepare it for storage.

Long Term Storage Instructions

It is important to prevent gum deposits from forming in

essential fuel system parts, such as the carburetor, fuel filter,

fuel hose or tank during storage. Also, alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract moisture,

which leads to separation and formation of acids during

storage. Acidic fuel can damage the fuel system of an engine

while in storage.

Protect Fuel System

Fuel Preserver:

Fill the fuel tank with fresh fuel allowing at least 1.5" of tank

space for fuel expansion as shown on page 8, when using a

fuel preserver cartridge with the fresh start fuel cap. If only

partially filled, air in the tank will promote fuel deterioration

during storage. Engine and fuel can be stored up to 6 months

with fuel preserver.

• Check level of fuel preserver cartridge. Fuel preserver is

dark in color.

• If cartridge is almost empty or empty, replace with a new

fuel preserver cartridge following the instructions in

“Fresh Start™ Fuel Cap” on page 9.

If fuel preserver is not used, remove all fuel from tank and

run engine until it stops from lack of fuel.

Change Oil

While engine is still warm, drain oil from crankcase. Refill

with recommended grade. See “Changing Oil” on page 17.

Oil Cylinder Bore

• Remove spark plug and pour about 1 ounce (30ml) of

clean engine oil into the cylinder.

• Install spark plug and crank slowly to distribute oil.

Generator

1. Clean generator as outlined in “Generator Cleaning”.

2. Check that cooling air slots and openings on generator

are open and unobstructed.

Other Storage Tips

1. DO NOT store fuel from one season to another unless it

has been treated as described in “Protect Fuel System”.

2. Replace fuel can if it starts to rust. Contaminated fuel

will cause engine problems.

3. If possible, store unit indoors and cover it to give

protection from dust and dirt.

4. Cover unit with a suitable protective cover that does not

retain moisture.

5. Store generator in clean, dry area.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WHEN DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Drain fuel tank outdoors.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• DO NOT light a cigarette or smoke.

WARNING

Unintentional sparking can result in fire or

electric shock.

• NEVER crank engine with spark plug removed.

WARNING

Storage covers can be flammable.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

TROUBLESHOOTING

Problem Cause Correction

Engine is running, but no AC output is

available.

1. Circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord

set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Sears or other qualified

service dealer.

3. Check and repair.

4. Connect another device that is in

good condition.

Engine runs good at no-load but "bogs

down" when loads are connected.

1. Short circuit in a connected load.

2. Engine speed is too slow.

3. Generator is overloaded.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. Contact Sears or other qualified

service dealer.

3. See "Don't Overload Generator".

4. Contact Sears or other qualified

service dealer.

Engine will not start; or starts and runs

rough.

1. Rocker Switch set to "Off".

2. Fuel Valve is in "Off" position.

3. Dirty air cleaner.

4. Out of fuel.

5. Stale fuel.

6. Spark plug wire not connected to

spark plug.

7. Bad spark plug.

8. Water in fuel.

9. Flooded.

10. Excessively rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Set switch to "On".

2. Turn fuel valve to "Open" position.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Drain gas tank and carburetor; fill

with fresh fuel.

6. Connect wire to spark plug.

7. Replace spark plug.

8. Drain fuel tank and carburetor; fill

with fresh fuel.

9. Wait 5 minutes and re-crank engine.

10. Contact Sears or other qualified

service dealer.

11. Contact Sears or other qualified

service dealer.

12. Contact Sears or other qualified

service dealer.

Engine shuts down when running.

Out of fuel. Fill fuel tank.

Engine lacks power.

1. Load is too high.

2. Dirty air filter.

1. See "Don't Overload Generator".

2. Replace air filter.

Engine "hunts" (speed constantly

fluctuates) or falters.

Carburetor is running too rich or too

lean.

Contact Sears or other qualified service

dealer.

La page charge ...

Simplicity 030243-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030243-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 030243-0 User manual

Simplicity 030243-0 Manuel utilisateur

Simplicity 030243-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents