Genie GCL-J&H 1/2HP Guide d'installation

Standard Duty Operator

GCL-J

&

H

™

JACKSHAFT/HOIST

PROPER APPLICATION

ALL TYPES

Jackshaft/Hoist

Hood Mount or

Wall Mount

Door Type Operator Type HP/Max Door Weight HP/Max Door Weight

(Sectional) (Rolling Steel)

1/2HP = 1120 lbs

3/4HP = 1370 lbs

1HP = 1620 lbs

1/2HP = 998 lbs

3/4HP = 1220 lbs

1HP = 1440 lbs

NOT FOR RESIDENTIAL USE

This Installation Manual provides the information required to install, troubleshoot and

maintain the GCL-J&H

™

Commercial / Industrial Door Operator.

111845.502351 04-14

MultiVolt®

EZ Limit®

TensiBelt®

THIS PAGE LEFT BLANK

TOC

............... . . . . . .

............... . . . . .

Table of Contents

Section 1 How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1

Section 2 Safety Information & Instructions . . . . . . . . . . . . . . . . 2.1-2.2

Section

3

Critical

Installation

Information . . . . . . . . . . . . . . . . . . . 3.1-3.5

Section 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1-4.8

Rolling Steel Front of Hood...................... . . 4.1-4.2

Sectional Chain Couple . . . . . . . . .................. . .

Rolling Steel Door Chart................ . . .... . . . . . . . . . 3.3

Sectional Door Chart. ........................... . . . . . . . 3.4

Chain Hoist and Keeper ........................... . . . .

Clutch Adjustment............................ . . . . . . . .

Section 5 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1-5.14

Safety Information/ Line Votage Wiring . . . . . . . . . . . . . 5.1-5.2

Low Voltage Control Wiring....................... . . . . . 5.3

External Wire Diagram ........................... . . . . . . 5.4

Wall Control ............................. . . . . . . . . . . . . . . 5.5

Interlock Switches (Rolling Steel) . . . . 5.6

Interlock Switches (Sectional) . . . . 5.7

Photocell Wiring............................... .

. . . . . . . 5.8

Sensing Edge Wiring . .......................... . .

5.9-5.10

External Radio ............................. . . . . . . . . . . 5.11

Motor Connection/Safety Information.......... . 5.12-5.14

Section 6 Operator Setup Procedures . . . . . . . . . . . . . . . . . . . . . . . . 6.1-6.10

Setting Close Direction............................ . . . . . . . . 6.2

Setting Braking Rate ............................ . . . . . . . . . . 6.3

Setting Travel Limits............................ . . . . . . . . . .

............................ . . . . ... . . .

6.4

Setting Limit Overrun ............................ . . . . . . . . . 6.5

Monitored Reversing Devices................... . . ...... . 6.10

Setting Open & Close Modes ........................... . . . 6.6

(Optional) Transmitter Programming .................. . . .

. 6.7

Setting Mid-Stop Limit ........................... . . . . . . . . . 6.8

Resetting the MRT. . 6.9

Section 7 Special Operational Features. . . . . . . . . . . . . . . . . . . . . 7.1-7.2

Operator Cycle Count .......................... . . . . . . . 7.1

GDO & Display Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1

Operator Type .............................. . . . . . . . . . . 7.2

Section 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1-8.5

Display Operation.............................. . . . . . . . 8.1

Error Codes .............................. . . . . . . . . . 8.1-8.2

Run Codes .............................. . . . . . . . . . . 8.2-8.3

LED Indicators ............................. . . . . . . . . . . . 8.4

Safe-T-Beam® Self-Diagnostic Troubleshooting Chart . . 8.5

Section 9 Service & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1

Section 10 Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1-10.13

Appendix A ............................. . . . . . . . . 10.1-10.9

Operator Parts Breakdown-Hoist. . . . . . . . . . . . . . . . . .10.1

Base Electric

Section 11 Warranty . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . .11.1

Operator Parts Breakdown Jackshaft . . . . . . . . . . . . . .10.2

Operator Parts Breakdown Hoist/Jackshaft Combo

. .10.3

4.4-4.6

4.8

4.7

Box Parts Breakdown . ............ . . .10.8

Electric Box Layout ....................... . . . . . . . .10.9

Appendix B ............................... . . . . . . . . 10.10

Screw Terminal Assignments ................. . 10.10

Appendix C .......................... . . . . . . . . .10.11-10.13

Run Codes .............................. . . . . . . . . 10.11

Error Codes....................... . . . . . . . . 10.12-10.13

Shaft Parts Breakdown Hoist. . . . . . . . . . . . . . . .... . . .10.5

Shaft Parts Breakdown Jackshaft . . . . . . . . . . . . . . . . . .10.6

Shaft Parts Breakdown Hoist/Jackshaft Combo. . . . .10.7

Rolling Steel Wall Mount............................. . . 4.3

04-14

Alternate Motor Options . . . . . . . . . . . . . . . . . . . . . . . . .

. .10.4

Section 1: How to use this manual

The 11 sections of this Installation Manual provide the information required to install, troubleshoot and maintain this commercial/industrial

door operator.

Section 2

Section 3

Sections 4-6

FOR ASSISTANCE CALL 1-800-843-4084.

Sections 7-8

Sections 9-11

1.1

04-14

Failure to correctly perform all steps in sections 4-6 can result in serious injury or death.

WARNING

AVERTISSEMENT

Ne pas effectuer correctement toutes les étapes dans les sections 4-6 peut entraîner des

blessures graves voire la mort.

2.1

Section 2: Safety Information & Instructions

www.geniecompany.com 01-14

WARNING

Commercial/Industrial Sectional and Rolling Steel Doors are large, heavy objects that move with the help of springs

under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause

injuries, your safety and the safety of others depend on you reading the information in this manual. If you have any

questions or do not under stand the information presented, call your nearest service representative. For the number

of your local Genie® Dealer, call 800-OK-GENIE, and for Genie® Factory Technical Advice, call 800-843-4084.

In this Manual, the words Danger, Warning, and Caution are used to stress important safety information. The word:

DANGER

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

IMPORTANT

READ PRIOR TO ANY DOOR OPERATION

POTENTIAL HAZARD EFFECT PREVENTION

Do Not operate unless the doorway is in sight and free of

obstructions. Keep people clear of opening while door is moving.

Do Not allow children to play with the door operator.

Do Not change operator control to momentary contact unless an

external reversing means is installed.

Do Not operate a door that jams or one that has a broken spring.

Could result in

Serious Injury

or Death

Turn off electrical power before removing operator cover.

When replacing the cover, make sure wires are not pinched or near

moving parts.

Operator must be electrically grounded.

Do Not try to remove, repair or adjust springs or anything to which

door spring parts are fastened, such as, wood block, steel bracket,

cable or any other structure or like item.

Repairs and adjustments must be made by a trained service

representative using proper tools and instructions.

HIGH SPRING TENSION

WARNING

MOVING DOOR

1. Read manual and warnings carefully.

2. Keep the door in good working condition.

Periodically lubricate all moving parts of door.

3. If door has a sensing edge, check

operations monthly. Make any necessary

repairs to keep it functional.

4. AT LEAST twice a year, manually operate

door. The Door should open and close freely.

If it does not, the door must be taken out of

service and a traine

d service representative

must correct the condition causing

the malfunction.

5. The Operator Motor is protected against

overheating by an internal t

hermal protector.

If the operator ceases to function because

motor protector has tripped, a trained service

technician may need to correct the condition

which caused the overheating. When motor

has cooled, thermal protector will

automatically

reset and normal operation can

be resumed.

6. In case of power failure, the door can be

operated manually by pulling the release

cable to disconnect the operator drive system.

7. Keep instructions in a prominent location

near the pushbutton.

Could result in

Serious Injury

or Death

WARNING

Could result in

Serious Injury

or Death

WARNING

ELECTRICAL SHOCK

2.2

Section 2: Safety Information & Instructions

www.geniecompany.com 04-14

AVERTISSEMENT

Les portes de garage commerciales/industrielles à sections et en acier roulantes sont de gros objets lourds qui fonctionnent à l’aide de ressorts soumis à une haute tension et

de moteurs électriques. Dans la mesure où les objets en mouvement, les ressorts sous tension et les moteurs électriques peuvent entraîner des blessures, votre sécurité et celle

des autres exigent que vous preniez connaissance des informations stipulées dans ce manuel. Si vous avez des questions ou si vous ne comprenez pas les informations

ci-incluses, veuillez contacter le représentant de service le plus près. Pour obtenir le numéro du revendeur Genie® local, appelez le +1 (800)-OK-GENIE, et pour obtenir

des conseils techniques de l'usine Genie®, appelez le +1 (800)-843-4084.

Dans ce manuel, les mots Danger, Avertissement, et Attention sont utilisés pour faire ressortir d’importantes informations relatives à la sécurité. Le mot :

DANGER

signale une situation dangereuse imminente qui si elle n'est pas évitée, risque d'entraîner des blessures graves, voire mortelles.

Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants éléments à prendre en considération.

DANGER POTENTIEL

EFFET

PRÉVENTION

Utiliser uniquement si la porte est en vue et libre de tout obstacle. Ne laisser personne

se tenir dans l’ouverture de la porte pendant qu’elle est en mouvement.

Ne pas permettre aux enfants de jouer avec l’opérateur de la porte.

Ne pas modifier la commande de l'opérateur à contact momentané à moins qu'un moyen

d'inversion externe soit installé.

Ne pas faire fonctionner une porte qui bloque ou dont le ressort est cassé.

Pourrait entraîner

des blessures

graves voire la mort

AVERTISSEMENT

Pourrait entraîner

des blessures

graves voire la mort

CHOC ÉLECTRIQUE

TENSION ÉLEVÉE DU RESSORT

PORTE EN MOUVEMENT

ATTENTION

signale une situation potentiellement dangereuse qui, si elle n'est pas évitée, risque d'entraîner des blessures ou des dommages matériels.

AVERTISSEMENT

signale une situation potentiellement dangereuse qui, si elle n'est pas évitée, risque d'entraîner la mort ou des blessures graves.

Pourrait entraîner

des blessures

graves voire la mort

Couper le courant avant d’enlever le couvercle de l'opérateur.

Lorsque le couvercle doit être remplacé, s’assurer que les fils ne sont ni

coincés ni près des pièces mobiles.

L’opérateur doit être correctement mis à la terre.

Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou toute autre pièce à laquelle le

ressort de la porte est attaché, y compris blocs de bois, supports en acier, câbles ou autres

articles semblables.

Les réparations et les réglages doivent être effectués par technicien qualifié qui se sert

d’outils appropriés et qui respecte les instructions.

AVERTISSEMENT

3.1

www.geniecompany.com 04-14

Job

Site Issues to Consider/Concerns

The following list of items should be considered prior to selecting an operator for a given job site.

1-Available power supply.

2-Type of door.

3-Potential operator mounting obstructions. Items to consider include, but are not limited to: side room, room above door shaft,

room below door shaft, available mounting

surface integrity, power supply location, and convenient chain hoist and release cable positioning.

4-Size of door for appropriate

operator torque and door travel speed selection.

ssenitsud ,ssenpmad dna noitacol rotarepo edulcni redisnoc ot smetI .tnemnorivne gnitnuom rotarepO-5

and corrosiveness of the location.

6-Door activation needs/requirements. Examples include 3

button control stations, 1 button control stations, radio controls, pull

cords,

loop detectors, photoelectric controls,

key switches, etc. See “Entrapment Protection” section below.

7-Interlock switches are required under certain conditions for

6-5.7..5 egap eeS .skcol rood dna srood ssap htiw srood

rof deriuqer( smaeb llecotohp

ro/dna segde gnisrever era selpmaxE .tnempiuqe yrosseccA-8

.cte ,sthgil gninraw ,syaler lortnoc yrailixua,),tcatnoc yratnemom sa etarepo ot tes srood

Section

3:

Critical

Installation

Information

ENTRAPMENT PROTECTION

The installation of a fail safe external reversing device (such as a monitored reversing edge or photocell system, etc.) is required on all momentary contact electronically

operated commercial doors. If such a reversing device is not installed, the operator will revert to a constant contact control switch for operation (Closing only).

The Reversing Devices currently UL Approved are:

MillerEdge ME and MT series monitored edge sensors used in combination with Timer-Close Module P/N OPABTCGX.S

MillerEdge ME and MT series monitored edge sensors used in combination with MillerEdge Interface Module OPAKMEIGX.S. (Direct connect through STB inputs.)

4)

Residential Safe-T-Beam® Monitored Photocells - P/N 37220R (GSTB-BX) & 38176R.S (includes extension brackets).

5)

Series II Commercial Safe-T-Beam® Monitored Photocells - P/N OPAKPE.S and OPAKPEN4GX.S (NEMA 4).

1)

2)

6) Monitored Retro-Reflective Photoeye - P/N OPGAKRPEN4X.S

MillerEdge Wireless monitored edge sensor OPAKMMWE.S.

3)

WARNING:

DO NOT apply line voltage until instructed to do so.

AVERTISSEMENT:

NE PAS mettre sous tension tant que l'instruction n'est pas donnée de le faire.

3.2

www.geniecompany.com 04-14

Section

3: Critical Installation Information

CAUTION:

Check working condition of door before installing the operator. Door must be free from sticking and binding.

If equipped, deactivate any door locking device(s). Door repairs and adjustments, including cables and spring assemblies MUST

be made by a trained service representative using proper tools and instructions.

ATTENTION:

Vérifiez l'état de fonctionnement de la porte avant d'installer l'opérateur.

La porte doit pouvoir bouger librement et ne pas coincer. Désactivez tous les dispositifs de verrouillage de la porte (si équipés).

Les réparations et les réglages de porte, plus particulièrement pour les câbles et les ressorts DOIVENT être effectués par un

technicien qualifié qui se sert d’outils appropriés et qui respecte les instructions.

Mult

— Offers all (available) voltage combinations in both single, and 3-phase units.

E

TensiBelt

®

Z Limit

®

— F

— Employs a self-adjustment feature for tensioning.

eatures patent pending electro-mechanical design that sets limits through the control panel that are maintainable even through a power outage.

New Features:

MultiVolt

®

ENTRAPMENT

PROTECTION

The operator can be used with the following UL Approved entrapment devices in compliance with UL325 requirements active starting August 29, 2010.

UNTIL ONE OF THESE MONITORED EXTERNAL ENTRAPMENT DEVICES IS INSTALLED, THE OPERATOR WILL NOT ALLOW MOMENTARY CONTACT OPERATION IN THE CLOSE DIRECTION.

Section

3: Critical Installation Information

3.3

Model HP

FireStar® 3” SLAT

INSULATED

SHEET DOOR

16GA. 18GA. 20GA. 22GA. 24GA. 26GA. 18GA. 20GA. 22GA.

ALUM. STL/SST 20GA. 22GA.

350 240 N/A

N/A

STEEL, NON-INSULATED STEEL, INSULATED

UL

L is ted

FireStar® 2” SLATGRILLESCOUNTER DOOR

ALUM. STL/SST

126 126

Rolling Steel Door Chart (sq. ft.)

Note: Total door weight and not square footage is the critical factor in selecting the proper operator. These Sq.Ft. measurements are based on square doors, e.g. 16' x 16'.

Unbalanced Fire Shutters have a maximum square footage of 52 for 22GA. steel and 42 for 20GA. steel.

GCL-J&H™ 1/2 YES

GCL-J&H™ 3/4 YES

GCL-J&H™ 1 YES

www.geniecompany.com 04-14

297 333 333 416 476 476 238 238 274

450 310 N/A

126 126

359 419 419 552 618 N/A 276 276 309

610 450 N/A

126 126

388 461 461 606 621 N/A 297 297 382

16GA. 18GA. 20GA. 22GA.

N/A N/A N/A

20GA. 22GA. 26GA.

N/A N/A 256

N/A N/A N/A

Miller Edge ME & MT series monitored edge sensors used in

combination with OPABTCGX.S Timer-Close Module or MillerEdge

Interface Module OPAKMEIGX.S. Miller Edge Wireless monitored edge sensor OPAKMMWE.S

ANY WIDTH

Residential Safe-T-Beams® P/N 37220R (GSTB-BX) and 38176R.S (includes ext. brkt’s)

Commercial Photoeye Kit P/N OPAKPE.S and OPAKPEN4GX.S (NEMA 4)

LISTED DEVICES

ALLOWABLE DOOR WIDTH

30 FEET

35 FEET

Monitored Retro-Refective Photoeye Kit P/N OPGAKRPEN4X.S

Type

Mounting

Max.

Door

Weight

(Lbs)

16GA.

Flush

Steel

16GA.

Flush

Steel

Insulated

20GA.

Ribbed

Steel

20GA.

Ribbed

Steel

Insulated

24GA.

Ribbed

Steel

24GA.

Ribbed

Steel

Insulated

Nominal

24GA.

Ribbed

Steel

Nominal

24GA.

Ribbed Steel

Insulated

PU/FIP

Insulated

PU/FIP

1.38"

1/8" Glass

1.38"

Glass

1.38"

Insulated

PU/FIP

2"

Insulated

PU/FIP

2"

20GA.

Yes TSC 1120 256 220 370 256 440 340 320 320 256 360 400 300 400 380 360 240

TSC 1370 330 256 440 310 530 400 320 320 256 450 450 370 460 440 400 330

TSC 1620 380 280 500 370 570 410 320 320 256 480 480 420 500 480 400 400

Yes

S=Jackshaft,SideMount

C=Jackshaft,CenterMount

UL L is tedHPModel

T=Trolley

Aluminum

Door S eries ->

Section 3: Critical Installation Information

3.4

Note: Total door weight, and not the square footage, is the critical factor in selecting the proper operator.

Square footage measurements are based on "square doors." (Example=16' x 16')

NOTE: Doors that require special windloading and wide doors, normally require increased strutting (reinforcement). Strutting doors can significantly increase door

weight beyond weight shown. Consult Customer Service for the impact of wind load andstrutting on square foot limits.

NOTE: "PU-FIP" stands for "polyurethane, foamed-in-place." If no notation is present, insulation is "polystyrene, layed-in-place."

Sectional Door Chart (sq. ft.)

GCL-J&H™ 1/2

GCL-J&H™ 3/4

GCL-J&H™ 1

www.geniecompany.com 04-14

216 216 ins. 220 220 ins. 2415 2415 ins. 2411 2411 ins. 125 150 200 200-20 5150 5200 451 452

CommercialSteelInsulated&Non-Insulated Thermospan Thermomark

Exterior

Insulated

PU/FIP

Raised

Panel

1.38"

Insulated 1/4" or 1/2"

PU/FIP

Raised

Panel

2"

3.5

www.geniecompany.com 04-14

IMPORTANT

INSTALLATION INSTRUCTIONS

WARNING-

To reduce the risk of severe

injury or death:

READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

Install only on a properly operating and balanced door. A door that is

operating improperly could cause severe injury. Have qualified service

personnel make repairs to cables, spring assemblies and other

hardware before installing the operator.

Remove all pull ropes and remove, or make inoperative, all locks

(unless mechanically and/or electronically interlocked to the power

unit) that are connected to the door before installing the operator.

Install the door operator at least 8 feet above the floor if the operator

has exposed moving parts.

Do not connect the door operator to the power source until

instructed to do so.

Locate the control station: (a) within sight of the door, (b) a minimum

of 5 feet above the floor so that small children cannot reach it, and

(c) away from all moving parts of the door.

Install the Entrapment Warning Placard next to the control station

and in a prominent location.

For products having a manual release, instruct the end user on the

operation of the manual release.

IMPORTANT

INSTRUCTIONS D’INSTALLATION

AVERTISSEMENT-

Pour réduire les risques de

blessures graves ou de mort :

1)

LIRE ET RESPECTER TOUTES LES INSTRUCTIONS D'INSTALLATION.

2)

Installez uniquement sur une porte fonctionnant correctement et bien

équilibrée. Une porte qui fonctionne mal peut provoquer des blessures

graves. Demandez à un technicien qualifié d'effectuer les réparations

des câbles, des ressorts et de toute autre quincaillerie avant de

procéder à l'installation de l'opérateur.

Retirez toutes les cordes de traction ainsi que tous les verrous ou

rendez-les inopérants (à moins qu'ils ne soient mécaniquement et/ou

électroniquement interverrouillés à l'unité motrices) qui sont connectés

à la porte avant de procéderà l'installation de l'opérateur.

Installez l'opérateur de la porte à 2,4 m minimum au-dessus du sol

lorsque des pièces mobiles de l'opérateur sont exposées.

Ne pas raccorder l'opérateur de la porte à la source d’alimentation

avant que l'instruction ne soit donnée de le faire.

Installez la station de commande : (a) en vue de la porte, (b) à 1,5 m

minimum au-dessus du sol pour que les jeunes enfants ne puissent

pas l'atteindre, et (c) à l'écart de toutes les pièces mobiles de la porte.

Installez le poster d'avertissement de pincement à côté de la station de

commande à un endroit bien en vue.

Pour les produits ayant un déclenchement manuel, indiquez à l'utilisateur

comment déclencher manuellement.

3)

4)

5)

6)

7)

8)

1)

2)

3)

4)

5)

6)

7)

8)

Section 3: Critical Installation Information

www.geniecompany.com 01-14 4.1

The Rolling Steel Door Operator can be assembled for right-hand or

left-hand (Each model can also be

Section 4: Installation

Rolling Steel Doors

Front of Hood Installation

1) Remove wall mount brackets from operator. Attach rolling steel mounting

brackets to the operator using the fasteners provided.

Figure 1.

Figure 1

NOTE:

On Jackshaft units, release cable must be installed on operator

before unit is installed.

mounting Front of Hood.

wall mounted.) Typical mounting arrangements are shown.

2) Attach Operator to Powerhead Support bracket using the fasteners

provided. Figure 2.

5/16-18 X 3/4 CARRIAGE BOLT

& 5/16-18 FLANGE NUT

(QTY 6 EACH)

ROLLING STEEL

MOUNTING BRACKETS

Figure 2

5/16-18 X 1-1/4

CARRIAGE BOLT

(QTY 4 EACH)

USE THIS SET

OF HOLES

5/16-18 FLANGE NUT

(QTY 4 EACH)

USE THIS SET

OF HOLES

POWER HEAD SUPPORT

BRACKET

www.geniecompany.com 01-14 4.2

Front of Hood Installation (continued)

1) Install 12T #50 sprocket on operator output shaft.

2) Align keyways and insert ket into sprocket. Do not tighten set

screw at this time.

5) Assemble #50 chain using master link.

6) Align the door sprocket and operator output sprocket and

wrap #50 roller chain around both. Lock sprockets in place

by tightening their set screws.

7) Tension the drive chain using the slots in the powerhead

support bracket.

8) Tighten all mounting bracket hardware.

Figure 3

Chain Installation

(Figure 3)

#50 Drive Chain

3) Install #50 sprocket on door shaft.

4) Align keyways and insert ket into sprocket. Do not tighten set

screw at this time.

www.geniecompany.com 01-14 4.3

Rolling Steel Doors

Wall Mount Installation

Figure 4.

1) Install 12T #50 sprocket on operator output shaft.

2) Align keyways and insert key into sprocket. Do not tighten set

screw at this time.

5) Assemble #50 chain using master link.

6) Align the door sprocket and operator output sprocket and

wrap #50 roller chain around both. Lock sprockets in place

by tightening their set screws.

7) Raise or lower operator to remove slack from the chain.

Ensure operator output shaft is parallel with door shaft.

8) Secure Operator to the wall using lock down holes. Lock down

holes must be used to ensure proper chain tension.

Figure 4

LOCK DOWN HOLES

LOCK DOWN

HOLES

NOTE: Operator must be

securely fastened to the wall

using lock down holes to

ensure proper chain tension.

If using slotted mounting

holes to mount the unit, you

must use at least (2) lock

down holes in opposite

corners to firmly mount

the unit to the wall.

OPERATOR

MOUNTING

BRACKETS

NOTE: Door shaft

and operator output

shaft must be parallel

3) Install #50 sprocket on door shaft.

4) Align keyways and insert key into sprocket. Do not tighten set

screw at this time.

NOTE: On Jackshafts units, release cable must be installed on operator

before unit is installed.

The Operator can be assembled for right or left hand

mounting above or below the door shaft and is available with or

without hoist.

If you will be using the Tension Plate Kit shown on page 4.6, slide the

bearing plates on the operator output shaft. Assembly of the kit will be

done after the drive chain is installed.

1) Install #50 sprocket on operator output shaft.

2) Align keyways and insert key into sprocket. Do not tighten set

screws at this time.

4)

Align keyways and insert key into sprocket. Do not tighten set

screws at this time.

3)

Install #50 sprocket on door shaft.

INSTALLATION TIP:

While sprocket set screws are loose, if possible, manually operate

door to help align chain. A properly tensioned drive chain should deflect

no more than 1/2” when thumb pressure is applied mid-way between the

2 sprockets. While there is no hard and fast rule governing chain tension,

it must be tight enough to prevent clicking, popping and jumping the

teeth of the sprocket. The 1/2” guideline will insure sufficient tension.

Figure

5

4.4

www.geniecompany.com 01-14

Chain Couple Installation Figure 5.

Sectional Doors

LOCK DOWN HOLES

LOCK DOWN

HOLES

OPERATOR

MOUNTING

BRACKETS

5) Assemble #50 chain using master link.

6) Align the door sprocket and operator output sprocket and

wrap #50 roller chain around both. Lock sprockets in place

by tightening their set screws.

7) Raise or lower operator to remove slack from the chain.

Ensure operator output shaft is parallel with door shaft.

8) Secure Operator to the wall using lock down holes. Lock down

holes must be used to ensure proper chain tension.

NOTE: Operator must be

securely fastened to the wall

using lock down holes to

ensure proper chain tension.

If using slotted mounting

holes to mount the unit, you

must use at least (2) lock

down holes in opposite

corners to firmly mount

the unit to the wall.

NOTE: Door shaft

and operator output

shaft must be parallel

12”-15”

CENTER

DISTANCE

OPERATOR

OUTPUT SHAFT

DOOR

SHAFT

NOTE: On Jackshafts units, release cable must be installed on operator

before unit is installed.

For Hollow Counterbalance Door Shaft:

1) Use non-threaded hole in door shaft sprocket as a guide and

drill a 3/8” diameter hole through one side of the door shaft.

Fig. 6A.

2) Insert clevis pin through sprocket and shaft to hold sprocket

in position.

3) Drill through opposite side of shaft to obtain proper hole

alignment. Fig. 6B.

4) Insert clevis pin through both holes and secure with cotter pin.

Fig. 6C.

For Solid Counterbalance Door Shaft

:

1) Insert key into door shaft keyway.

2) Slide sprocket into place and secure with set screws.

To Complete the Installation:

If needed, realign operator sprocket with door sprocket. If you have

excessive door shaft movement, an optional chain tension plate is

available. Fig. 7, pg 4.6.

Chain Couple (continued)

SPROCKET HUB

DRILL HOLE

IN THIS SIDE

OF SHAFT

DRILL HOLE IN

OPPOSITE SIDE

OF SHAFT

DOOR SHAFT

(TUBE)

DOOR SHAFT

(TUBE)

CLEVIS PIN

COTTER PIN

DOOR SHAFT

(TUBE)

Figure 6A

Figure 6B

Figure 6C

4.5

www.geniecompany.com 01-14

Kit available separately, P/N 111005.0001.S for 1" door shaft. 111005.0002.S for 1

1

/4" door shaft.

Installation of optional chain spreader bracket: Fig 7A & 7B

1) Place drive chain sprocket and bearing plate assembly on door

shaft as shown.

2) Place bearing plate assembly and sprocket on operator shaft

as shown.

3) Install door and operator sprockets and chain assembly as

described in preceding instructions. See page 4.4.

4) Install bolts and nuts through plates. Do not tighten.

5) Tension chain by raising or lowering the operator as needed.

Tighten operator mounting bolts.

6) Align sprockets to achieve a 90° angle between the chain and

the shafts. Tighten all set screws.

7) Tighten Tension Plate bolts.

Chain Couple (continued)

(Tension Plate Kit)

DOOR SHAFT

SPROCKET

DOOR SHAFT

CHAIN

TENSION

PLATE

OPERATOR

OUTPUT

SHAFT

KEY

SET SCREW

OPERATOR

SHAFT

SPROCKET

COTTER PIN

CLEVIS PIN

HOLLOW COUNTERBALANCE

DOOR SHAFT

Figure 7B

OPERATOR

SHAFT

DOOR

SHAFT

90°

Figure 7A

DOOR SHAFT

SPROCKET

DOOR SHAFT

KEY

SET SCREW

CHAIN

SET SCREW

CHAIN

TENSION

PLATE

OPERATOR

OUTPUT

SHAFT

KEY

SET SCREW

OPERATOR

SHAFT

SPROCKET

SOLID COUNTERBALANCE

DOOR SHAFT

4.6

www.geniecompany.com 01-14

4.7

www.geniecompany.com 01-14

1) Route the hand chain through the chain guide, around the

pocket wheel and back through the chain guide. Fig. 8.

2) Connect the hand chain ends together as shown in Fig 9.

by twisting open the last link on one end of the chain, and

slipping the last link on the opposite end onto the open link.

3) Twist open link closed again.

4) Mount chain keeper to wall in line with chain approximately

4 feet from floor.

5) Loop chain around keeper as shown. Fig. 10. Optional Padlock

not provided.

6) Install hoist cable.

• With operator installed motor DOWN, attach hoist cable to

cam arm hole closest to mounting plate. Fig. 11.

• With operator installed motor UP, attach hoist cable to cam

arm hole closest to electric box. Fig. 11.

Hand Chain and Keeper

Figure 9

Figure 10

NOTE: To insure smooth operation, make sure there is no twist in the

hand chain before connecting the link ends together.

MOUNTED

MOTOR UP

MOUNTED

MOTOR DOWN

ATTACH

HOIST

CABLE

HERE

Figure 11

ATTACH

HOIST

CABLE

HERE

Figure 8

4.8

The Operators have a friction style clutch that can be adjusted.

NOTE: The clutch is intended to provide protection for the door, the

operator and associated equipment. It is not intended for entrapment

protection.

To Adjust the Clutch

1) Decrease the compression on the clutch until the operator will

not lift the door.

• Turning the adjustment castle nut counter-clockwise will

decrease compression and clockwise will increase compression.

2) Gradually increase compression until the operator will perform a

complete open and close cycle without clutch slippage.

3) Insert a cotter pin through the adjustment castle nut and bend a

leg of the cotter pin to hold it in place.

NOTE: Periodically check the system for proper clutch action. If clutch

starts to slip after working properly for some time , check manual

operation of door BEFORE adjusting clutch. The door may not be

operating freely or the counterbalance spring may need adjusting. Repairs

and adjustments must be performed by a trained service representative

using

proper tools and instructions.

Clutch Adjustment Fig. 12

CLUTCH PULLEY

WASHER

COTTER PIN

ADJUSTING NUT

CLUTCH

PAD

CLUTCH

PLATE

SPRING

www.geniecompany.com

Figure 12

01-14

5.1

Section 5: Wiring

www.geniecompany.com 04-14

WARNING

• DO NOT apply power to operator until instructed to do so.

•

It is strongly recommended, and may be required by law

in some areas, that line voltage wiring be performed by

a qualified electrician.

• Be sure that electrical power has been disconnected from

the input power wires being connected to the operator

prior to handling these wires. An appropriate lock-out/

tag-out procedure is recommended.

•

Line voltage wiring must meet all local building codes.

•

Make sure operator voltage, phase and frequency nameplate

ratings are identical to the job site line voltage ratings.

•

Input power wiring must be properly sized for the operators

amperage rating located on the nameplate.

•

To reduce the risk of electric shock, make sure the chassis of

this unit is properly grounded.

AVERTISSEMENT

• NE PAS mettre sous tension tant que l'instruction n'est

pas donnée de le faire.

•

Il est fortement recommandé voire même exigé par la loi dans

certaines régions, de contacter un électricien qualifié pour

l'acheminement du fil électrique.

• Assurez-vous que l'alimentation électrique a été déconnectée

des câbles d'alimentation d'entrée connectés à l'opérateur

avant de manipuler ces câbles. Une procédure de verrouillage/

étiquetage appropriée est recommandée.

•

Le câblage au secteur doit satisfaire à tous les codes de

construction locaux.

•

Assurez-vous que les valeurs nominales de la plaque

signalétique pour tension, phase et fréquence de l'opérateur

correspondent à celles des tensions de l'alimentation sur site.

•

La capacité d'entrée doit correspondre à la valeur nominale de

l'ampérage des opérateurs indiquée sur la plaque signalétique.

•

Pour réduire le risque de choc électrique, assurez-vous que le

châssis de l'unité est correctement mis à la terre.

La page charge ...

Genie GCL-J&H 1/2HP Guide d'installation

Ce manuel convient également à

Genie GCL-J&H 1/2HP Guide d'installation

dans d''autres langues

Documents connexes