BST FIRST-SA15DSP2 Le manuel du propriétaire

Catégorie
Subwoofers
Taper
Le manuel du propriétaire
FIRST
SERIES
U s e r ’ s G u i d e
F I R S T-S P 0 8
F I R S T-S P 1 0
F I R S T-S P 1 2
F I R S T-S P 1 5
F I R S T-S P 2 1 5
F I R S T-S P 1 2 S
F I R S T-S P 1 5 S
F I R S T-S P 1 8 S
F I R S T-S A 1 0 D S P 2
F I R S T-S A 1 2 D S P 2
F I R S T-S A 1 5 D S P 2
F I R S T-S A 2 1 5 D S P 2
F I R S T-S A 1 2 S D S P 2
F I R S T-S A 1 5 S D S P 2
F I R S T-S A 1 8 S D S P 2
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 1
FIRST-Serie s
E N G LI SH
Thank you for having chosen our speaker system. For your own safety, please read this user manual
carefully before installing the device.
SAFETY INTRODUCTION:
Ÿ If the device has been exposed to temperature changes due to environmental changes, do not switch it
on immediately. The arising condensation could damage the device. Leave the device switched off until
it has reached room temperature.
Ÿ It is essential that the device is earthed. A qualied person must carry out the electric connection.
Ÿ Make sure that the available voltage is not higher than stated at the end of this manual.
Ÿ Make sure the power cord is never crimped or damaged. If it is damaged, ask your dealer or authorized
agent to replace the power cord.
Ÿ Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power cord by plug. Never pull out the plug by tugging the power cord.
Ÿ DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
CAUTION:
1. Please be aware that damages caused by manual modications to the device are not subject to
warranty. Keep away from children and non-professionals.
2. The light doesnt include any spare parts for repair, please check if all the parts are well installed and
screws are fitted tightly before operating. Do not use the light when the cover is open.
GENERAL GUIDELINES:
Ÿ This device is only allowed to be operated with an alternating current of max. 110-240VAC/50-60Hz and
was designed for indoor use only.
Ÿ Operate the device only after having familiarized yourself with its functions. Do not permit operation by
person not qualied for operating the device. Most damages are the result of unprofessional operation.
Ÿ Please use the original packaging if the device is to be transported.
Ÿ For safety reasons, please be aware that all modications on the device are forbidden. Furthermore,
any other operation may lead to short-circuit, burns, electric shock, crash, etc. If this device will be
operated in any way dierent to the one described in this manual, the product may suer damages and
the guarantee becomes void.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 2
S P E CI FI C AT IO N S - PA SS I V E
FI R S T- S e r i e s
ITEM NO
FIRST-SP08
FIRST-SP10
FIRST-SP12
FIRST-SP15
FIRST-SP215
TYPE
8'' 2-way full range
speaker, passive
10'' 2-way full range
speaker, passive
12'' 2-way full range
speaker, passive
15'' 2-way full range
speaker, passive
Dual 15'' 2-way full
range speaker,
passive
Freq.Response
(-10dB)
65Hz-20KHz
55Hz-20KHz
50Hz-20KHz
45Hz-20KHz
45Hz-20KHz
Sensitity
(1W@1M)
96dB
97dB
98dB
99dB
101dB
Power Handling
(RMS)
150 watts
200 watts
250 watts
300 watts
600 watts
Nominal
Impedence
8 ohms
8 ohms
8 ohms
8 ohms
4 ohms
Driver
LF 8'' woofer, 2'' VC,
30 OZ
LF 10'' woofer, 2''
VC, 30 OZ
LF 12'' woofer, 2.5''
VC, 50 OZ
LF 15'' woofer, 3''
VC, 60 OZ
LF 15'' woofer, 3''
VC, 60 OZ
HF 1'' compression
driver
HF 1.35''
compression driver
HF 1.35''
compression driver
HF 1.75''
compression driver
HF 1.75''
compression driver
Grille
Steel grille with
acoustic fabric
Steel grille with
acoustic fabric
Steel grille with
acoustic fabric
Steel grille with
acoustic fabric
Steel grille with
acoustic fabric
Enclosure
15mm Plywood
15mm Plywood
15mm Plywood
15mm Plywood
15mm Plywood
Appearance Finish
Texture Painting
Texture Painting
Texture Painting
Texture Painting
Texture Painting
Dimensions
(W x H x D)
300x330x490mm
350x380x585mm
410x430x670mm
475x500x750mm
485x530x1180mm
Net Weight
9.70kg
13.60kg
18.50kg
23.50kg
37.20kg
ITEM NO
FIRST-SP12S
FIRST-SP15S
FIRST-SP18S
TYPE
12'' Bass reflex subwoofer,
passive
15'' Bass reflex subwoofer,
passive
18'' Bass reflex subwoofer,
passive
Freq.Response (-10dB)
40Hz-160Hz
35Hz-160Hz
30Hz-160Hz
Sensitity (1W@1M)
100dB
102dB
102dB
Power Handling (RMS)
400 watts
500 watts
600 watts
Nominal Impedence
8 ohms
8 ohms
8 ohms
Driver
LF 12'' subwoofer, 3'' VC, 80
OZ
LF 15'' subwoofer, 4'' VC, 125
OZ
LF 18'' subwoofer, 4'' VC, 125
OZ
Grille
Steel grille with acoustic fabric
Steel grille with acoustic fabric
Steel grille with acoustic fabric
Enclosure
15mm Plywood
15mm Plywood
18mm Plywood
Appearance Finish
Texture Painting
Texture Painting
Texture Painting
Dimensions (W x H x D)
420x510x520mm
490x600x610mm
580x700x715mm
Net Weight
21.50kg
31.50kg
44.50kg
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 3
S P E CI FI C AT IO N S - A C T IV E F U LL R A N GE
FI R S T- S e r i e s
ITEM NO
FIRST-SA10DSP2
FIRST-SA12DSP2
FIRST-SA15DSP2
FIRST-SA215DSP2
TYPE
10'' 2-way full range
speaker, active
12'' 2-way full range
speaker, active
15'' 2-way full range
speaker, active
Dual 15'' 2-way full
range speaker, active
Freq.Response
(-10dB)
55Hz-20KHz
50Hz-20KHz
45Hz-20KHz
45Hz-20KHz
Sensitity (1W@1M)
97dB
98dB
99dB
101dB
Power Handling (RMS)
200 watts
250 watts
300 watts
600 watts
Nominal Impedence
4 ohms
4 ohms
4 ohms
4 ohms
Driver
LF 10'' woofer, 2'' VC, 30
OZ
LF 12'' woofer, 2.5'' VC,
50 OZ
LF 15'' woofer, 3'' VC, 60
OZ
LF 15'' woofer, 3'' VC, 60
OZ
HF 1.35'' compression
driver
HF 1.35'' compression
driver
HF 1.75'' compression
driver
HF 1.75'' compression
driver
Grille
Steel grille with acoustic
fabric
Steel grille with acoustic
fabric
Steel grille with acoustic
fabric
Steel grille with acoustic
fabric
Enclosure
15mm Plywood
15mm Plywood
15mm Plywood
15mm Plywood
Appearance Finish
Texture Painting
Texture Painting
Texture Painting
Texture Painting
Dimensions
(W x H x D)
350x380x585mm
410x430x670mm
475x500x750mm
485x530x1180mm
Net Weight
14.50kg
20.00kg
25.00kg
39.00kg
TYPE
Two-way BI-Amp
Two-way BI-Amp
Two-way BI-Amp
Amp type
Class D
LF Class-D, HF Class AB
LF Class-D, HF Class
AB
Output power
LF175W+HF75W
LF300W+HF60W
LF500W+HF80W
DSP
48Bit, 96kHz samplying
freqency
48Bit, 96kHz samplying freqency
48Bit, 96kHz samplying
freqency
DSP display screen
/
Yes
Yes
Modes
PA, Monitor, Sub,
Speech
Live, Music, Speech, DJ
Live, Music, Speech, DJ
Bluetooth module
Yes
Yes
Yes
Connectors
Combo Line/Mic in, RCA
in, Bluetooth in, XLR Mix
out
2xCombo Line/Mic in, Bluetooth in, XLR Mix out
2xCombo Line/Mic in,
Bluetooth in, XLR Mix
out
Controls
Two input volume
controls, master volume
control
Two input volume controls, master volume
control/DSP functions selector
Two input volume
controls, master volume
control/DSP functions
selector
Front LED Switch
On/off front LED switch
On/off front LED switch
On/off front LED switch
Indicators
BT Status, Limit, Signal,
Power, DSP 4 Modes
Limit, Signal, Power
Limit, Signal, Power
Protection
Over temp, over load,
DC protect, over
voltage, low voltage, soft
start
Over temp, over load, DC protect, over voltage,
low voltage, soft start
Over temp, over load,
DC protect, over
voltage, low voltage, soft
start
Cooling
Convection
Convection
Convection
Power Supply
230AC 50Hz
230AC 50Hz
230AC 50Hz
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 4
S P E CI FI C AT IO N S - A C T IV E S U BWO O F ER
FI R S T- S e r i e s
ITEM NO
FIRST-SA12SDSP2
FIRST-SA15SDSP2
FIRST-SA18SDSP2
TYPE
12'' Bass reflex subwoofer,
active
15'' Bass reflex subwoofer,
active
18'' Bass reflex subwoofer,
active
Freq.Response (-10dB)
40Hz-160Hz
35Hz-160Hz
30Hz-160Hz
Sensitity (1W@1M)
100dB
102dB
102dB
Power Handling (RMS)
400 watts
500 watts
600 watts
Nominal Impedence
4 ohms
4 ohms
4 ohms
Driver
LF 12'' subwoofer, 3'' VC, 80
OZ
LF 15'' subwoofer, 4'' VC, 125
OZ
LF 18'' subwoofer, 4'' VC, 125
OZ
Grille
Steel grille with acoustic fabric
Steel grille with acoustic fabric
Steel grille with acoustic fabric
Enclosure
15mm Plywood
15mm Plywood
18mm Plywood
Appearance Finish
Texture Painting
Texture Painting
Texture Painting
Dimensions (W x H x D)
420x510x520mm
490x600x610mm
580x700x715mm
Net Weight
23.50kg
33.50kg
46.50kg
TYPE
Active Sub Amp
Active Sub Amp
Active Sub Amp
Amp type
Class D
Class D
Class D
Output power
400W
500W
600W
DSP
48Bit, 96kHz samplying
freqency
48Bit, 96kHz samplying
freqency
48Bit, 96kHz samplying
freqency
DSP display screen
Yes
Yes
Yes
Modes
Live, Music, DJ1, DJ2
Live, Music, DJ1, DJ2
Live, Music, DJ1, Dj2
Bluetooth module
Yes
Yes
Yes
Connectors
2xCombo Line/Mic in,
Bluetooth in, 2xXLR Mix out
2xCombo Line/Mic in,
Bluetooth in, 2xXLR Mix out
2xCombo Line/Mic in,
Bluetooth in, 2xXLR Mix out
Controls
Master volume control/DSP
functions selector
Master volume control/DSP
functions selector
Master volume control/DSP
functions selector
Front LED Switch
On/off front LED switch
On/off front LED switch
On/off front LED switch
Indicators
Limit, Signal, Power
Limit, Signal, Power
Limit, Signal, Power
Protection
Over temp, over load, DC
protect, over voltage, low
voltage, soft start
Over temp, over load, DC
protect, over voltage, low
voltage, soft start
Over temp, over load, DC
protect, over voltage, low
voltage, soft start
Cooling
Convection
Convection
Convection
Power Supply
230AC 50Hz
230AC 50Hz
230AC 50Hz
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 5
A M P LI FI E R I NP UT C O N FIG U R ATI O N
FI R S T- S e r i e s
Full-Range Models
Subwoofer Models
1 3
4
5
6
7
12
11
8
9
10
1 2
3
4
5
6
7
8
9
10
14
13
15
16
1
3
4
5
6
7
8
9
10
1211
1
3
4
5
6
7
8
9
10
12
11
FIRST-SA10DSP2
FIRST-SA12DSP2
FIRST-SA12SDSP2
FIRST-SA15SDSP2
FIRST-SA18SDSP2
FIRST-SA15DSP2
FIRST-SA215DSP2
1. LINE / MIC IN
Balanced input for the connection of signal sources like mixing
consoles, instruments, or microphones. Connections can be
established using 1/4 inch TRS or XLR connectors.
Volume control for adjusting the individual inputs’ level. The 12 o'clock
position is unity gain (no gain or attenuation), the range to the left of
zero(0) is for adjusting line level sources, and the range to the right of
zero(0) is for adjusting microphone levels. LINE and mic input level
control is available for both INPUT 1 and INPUT 2.
2. AUX/BT Input
A CD, IPhone and Bluetooth signal for AUX/BT in or Input 2 channel
input.
3. MIX OUT
XLR output sends the mix of both input signals to another loudspeaker
or subwoofer. INPUT LEVEL controls the signal level to OUTPUT. The
MASTER VOL or DSP control setting do not aect OUTPUT.
4.LIMIT(Automatioc amplitude limiter):
Automatic amplitude “LIMIT” LED; when the audio signal reaches the
dangerous threshold for the transducers, this circuit will automatically
intervenes by reducing the amount of signal in order to protect the
speaker, avoide losing roue and despicking distortion as well; the
activation of these protections is recognized via the “CUP” Leds
Lighting up.
5.SIGNAL
LED signal to indicate the input signal to “IN XLR SOCKET. Adjusts the
volume of the main mix.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 6
A M P LI FI E R I NP UT C O N FIG U R ATI O N
FI R S T- S e r i e s
6.POWER
LED signal to indicate the switching on of the system.
7. FRONT LED
Turn on/off front logo LED.
8. POWER SWITCH
This power switch turns on the system. Remember to adjust the volume level to the lowest setting before turn on the
power switch.
9. AC INPUT CONNECTOR
Connect the included power cord to the AC input connector before push on the power switch.
10. Fuse
Only replace the fuse when the device is disconnected from mains. Only use fuses of the same rating and power. The
correct fuse value is specied on the rear panel.
11. LCD
DSP control and monitoring interface.
12. MASTER VOLUME
Adjusts the sound level.
DSP: Scroll through the menu and select the available choices. Push the MASTER VOL knob to enter the DSP menu.
13. SPEAKER MODE:
PA: This is the default setting for the loudspeakers. Use this setting when your loudspeaker is being used either on a
speaker stand and facing towards your audience.
DJ: Use this setting when you loudspeaker is being used for DJ only or play DJ music application and is facting
towards the audience.
Monitor: Use this setting when your loudspeaker is being used as a stage monitor facing towards you.
Speech: Use this setting when your loudspeaker is being used for Speech only or Spoken Word only applications and
is facing towards the audience.
14. BLUETOOTH:
To repair the speaker to your Bluetooth device:
A: With the loudspeaker powered on, press the pair button for two seconds, the Bluetooth on. The paired LED will
ash.
B: From you Bluetooth device's settings page, enable Bluetooth and select MIX-01 as the device. When paired
successfully, the paired LED is light solid.
C: Turn your Bluetooth device's volume to its lowest setting.
D: On your Bluetooth device, play music. Then we recommend setting the Bluetooth device's volume at its maximum.
E: Once your device's is paired to the speaker, the speaker will remember the device's.To reconnect it, go to your
device's Bluetooth settings page and select “Connect" to re-establish the connection.
F: When the device's connected Bluetooth is playing, press the Pair button for fast play and pause operation, when
you press the pair button for 2 seconds, the devices is disconnected, and the Bluetooth power o.
15.BLUETOOTH VOLUME
Turn this knob to adjust the input volume of you paired Bluetooth device.
16.MIX OUT SELECTOR
When disengaged(Ch1), the MIX OUT level will be unaected by the IPNUT VOLUME controls.
When engaged(MIX), the MIX OUT level can be adjusted by the INPUT VOLUME controls.
An integrated DSP controls menu allows the user to select multiple DSP system setting on the loudspeaker.
To access the DSP controls menu, do the following;
1. Push the Master Vol Knob, the DSP Control menu appears.
2. Using the Master Vol Knob, scroll through the menu items.
3. Push the Master Vol Knob to select the menu item you want to modify. the focus moves to the parameters on the
right side of the DSP menu.
4. Using the Master Vol knob, scroll through the parameters.
5. Push the Master Vol Knob to conrm the selected parameter.
The setting is saved. The focus returns to the menu items on the left side of the DSPmenu.
6. Repeat steps 2 through 5 to modify additional DSP and system setting.
7. Select EXIT to return to the home screen.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 7
D S P CO N T ROL
FI R S T- S e r i e s
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 8
D S P CO N T ROL OF F UL L RA NG E
FI R S T- S e r i e s
Mode
LIVE (default)
MUSIC
SPEECH
DJ
LOACTION
TRIPOD (default)
MONITOR
WALL
SUPEND
SUB
OFF(default)
80Hz
100Hz
120Hz
150Hz
TREBLE
0dB (default)
-12dB+12dB
MID
0dB (default)
-12dB+12dB
BASS
0dB (default)
-12dB+12dB
DELAY
0-116m
BTH VOL
OFF (default)
Bluetooth Connected
LCD DIM
ON (default)
OFF
BRIGHT
5 (default)
1-10 adjust
RESET
NO (default)
ARE YOU SURE?
YES OR NO
INFO
Brand Product Name
Firmware Version
EXIT
The full-range loudspeaker DSP control menu selections are available for the 12" and 15'' loudspeakers.
* Notice !
The display returns to the home screen after twenty second of inactivity.
Mode Menu
The Mode menu is used to congure the type of sound the loudspeaker delivers.
Available options for this selection are : LIVE, MUSIC, SPEECH and DJ.
Ÿ LIVE - is used for live sound applications (Default).
Ÿ MUSIC - is used for recorded music playback.
Ÿ SPEECH - is used for spoken word applications.
Ÿ DJ - is used for recorded electronic music playback.
LOCATION Menu
Ÿ The Location menu is used to optimize the loudspeaker for dierent boundaries
Ÿ Available options for this selection are: TRIPOD, MONITOR, WALL, and SUSPEND.
Ÿ TRIPOD - is used when the loudspeaker is placed on a tripod stand or placed on a pole.(Default)
Ÿ MONITOR - is used when the loudspeaker is placed on the angled monitor panel in monitor position. This setting
compensates for the amount of low frequency boost created by placing the speaker close to the floor.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 9
D S P CO N T ROL OF F UL L RA NG E
FI R S T- S e r i e s
Ÿ WALL - is used when the loudspeaker is mounted to the wall using the mounting bracket. This setting compensates
for the amount of low frequency boost created by placing the loudspeaker close to the wall. If used on a column, it is
recommended to use the SUSPENDmode.
Ÿ SUSPEND - is used when the loudspeaker is suspended in a 3-point suspension by eye bolts.
SUB Menu
The Sub menu is used to select a high pass frequency for use with a subwoofer or a matched subwoofer. Available
options for this selection are: OFF, 80Hz, 100Hz, 120Hz, 150Hz, 15"/18". The high passes are 24dB / octave
Linkwitz/Riley crossovers. The 80 Hz, 100 Hz, 120 Hz, and 150 Hz choices are generic high pass settings for use with
other subwoofers. The 15 Sub/18 Sub settings are specically optimized for subwoofers by including delay for best
summation. The default is OFF.
TREBLE Menu
The Treble menu is used to adjust the high frequency performance of the loudspeaker for dierent applications or
personal preference. The parameter controls a high shelving filter that is centered on 6 kHz. The range is-12 dB to+ 6
dB. The default is zero (0).
MID Menu
The Mid menu is used to adjust the midrange frequency performance of the loudspeaker for dierent applications or
personal preference. The parameter controls a parametric EQ that is centered on 1.2 kHz. The range is -12dB to
+6dB. The default is zero (0).
BASS Menu
The Bass menu is used to adjust the low frequency performance of the loudspeaker for dierent applications or
personal preference. The parameter controls a parametric EQ filter that is centered on 80 Hz. The default is zero (0).
DELAY Menu
The DELAY menu is used to adjust the delay time, The range is 0-30ms.
BTH VOL Menu
The bluetooth menu on the DSP is used to match and connect with the bluetooth on the mobile devices. Inter the menu
and adjust the Volume to the range of 0-16,at the same time make the bluetooth in the searching condition., and the
bluetooth symbol flashing on the LCD. Then open the bluetooth on the moble device to match with the bluetooth in the
loudspeaker. The bluetooth symbol stop flashing when the bluetooth match success. At this time you can play music
on the speaker via mobile devices, and the range of 0-16 is to control the loudspeaker bluetooth volume. the
loudspeaker bluetooth closed when adjust to 0.
LCD DIM Menu
The LCD Dim menu is used to dim the display when the display is idle for twenty second. Available options for this
selection are: ON or OFF. The default is ON.
BRIGHT Menu
The Bright menu is used to determine the brightness of the LCD. The range is 1 to 10. The default is 5.
CONTRAST Menu
The Contrast menu is used to determine the contrast on the LCD. The range is 1 to 10. The default is 5.
RESET Menu
The Reset menu is used to reset the loudspeaker to original factory settings. Available options for this selection are:
NO or YES. The default selection is NO. To reset the system to original factory settings, do the following:
1. From the DSP menu, select RESET.
The reset Conrm Reset message appears
2. Select YES.
The loudspeaker restarts and resets the system to the original factor settings.
INFO Menu
The Information menu is used to display the Brand, product name and firmware version.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 10
D S P CO N T ROL OF S UB W O OF ER
FI R S T- S e r i e s
The subwoofer DSP control menu selections are available for the 12", 15'' and 18'’ subwoofers.
* Notice !
The display returns to the home screen after twenty second of inactivity.
Mode Menu
The Mode menu is used to congure the type of sound the subwoofer delivers.
Available options for this selection are: MUSIC, LIVE, and CLUB.
Ÿ LIVE - is used for recorded music playback and EDM applications. (Default)
Ÿ MUSIC - is used for live sound applications.
Ÿ DJ1- is used for recorded electronic music playback.
Ÿ DJ2 - is used for recorded electronic music playback.
LOW PASS Menu
The LOW PASS menu is used to select low pass frequency for proper summation with a full-range loudspeaker.
Available options for this selection are: 80Hz, 100Hz, 120Hz, 150Hz, 12", 15". The low passes are 24dB / octave
Linkwitz / Riley slopes. The 80Hz, 100Hz, 120Hz, and 150 Hz selections are generic low pass settings for use with
other full-range loudspeaker systems. 12", 15" settings are specically optimized for full-range loudspeakers for best
summation. The default is OFF.
POLARITY Menu
The POLARITY Menu is used to adjust the loudspeaker polarity. The default is Polarity+.
LCD DIM Menu
The LCD Dim menu is used to dim the display when the display is idle for twenty second. Available options for this
selection are: ON or OFF. The default is ON.
BRIGHT Menu
The Bright menu is used to determine the brightness of the LCD. The range is 1 to 10. The default is 5.
CONTRAST Menu
The Contrast menu is used to determine the contrast on the LCD. The range is 1 to 10. The default is 5.
Mode
LIVE(default)
MUSIC
Dj1
Dj2
Low Pass
OFF(default)
80Hz
100Hz
120Hz
150Hz
12"
15"
DELAY
OFF(default)
0-30ms
POLARITY
POL+(default)
POL
LCD DIM
ON(default)
OFF
BRIGHT
5(default)
1-10 adjust
RESET
ON(default)
ARE YOU SURE?
YES OR NO
INFO
Brand Prouduct Name
Firmware Version
EXIT
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 11
D S P CO N T ROL OF S UB W O OF ER
FI R S T- S e r i e s
RESET Menu
The Reset menu is used to reset the loudspeaker to original factory settings. Available options for this selection are:
NO or YES. The default selection is NO.
To reset the system to original factory settings, do the following:
1. From the DSP menu, select RESET.
The reset Conrm Reset message appears
2. Select YES.
The loudspeaker restarts and resets the system to the original factor settings.
INFO Menu
The Information menu is used to display the Brand, product name and firmware version.
Daisy chaining full-range systems
Using full-range systems as monitors
Mode:
Speech
Location:
Tripod
Sub:
O
Mode:
Live
Location:
Monitor
Sub:
O
CD/DVD Stereo congurations
Stacking full-range systems with subwoofers
Mode:
Music
Location:
Tripod
Sub:
O
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 12
A P P LI CAT I O N EX A M PLE
FI R S T- S e r i e s
18'' SUB
15''
Live
Tripod
18' SUB
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 13
FI R S T- S e r i e s
FR A NC AI S
Nous vous remercions pour lachat de ce système de sonorisation. Pour votre sécurité, lisez
attentivement ce manuel avant dinstaller lappareil.
CONSIGNES DE SECURITE ET DUTILISATION :
Ÿ Si lappareil a été exposé à des changements de température, ne le mettez pas immédiatement sous
tension. La condensation qui peut se produire, risque dendommager les circuits. Attendez que
lappareil ait atteint la température ambiante avant de le mettre sous tension.
Ÿ L’appareil fait partie de la classe de protection I. Il est donc primordial quil soit relié à la terre.
Ÿ Assurez-vous que la tension secteur ne dépasse pas celle indiquée à la fin de ce mode demploi.
Ÿ Assurez-vous que le cordon dalimentation nest pas écrasé ou endommagé. Dans ce cas, demandez à
votre revendeur ou un technicien de remplacer le cordon.
Ÿ Débranchez toujours lappareil du secteur lorsquil nest pas utilisé ou avant de le nettoyer. Ne tirez que
sur la fiche, jamais sur le cordon.
Ÿ Lorsque le cordon d'alimentation ou un coupleur d'appareil est utilisé comme dispositif de déconnexion,
ce dispositif doit rester facilement accessible Si un interrupteur omnipolaire est utilisé comme dispositif
de déconnexion, l'emplacement sur l'appareil et la fonction de l'interrupteur doit être décrite, et le
commutateur doit rester facilement accessible
ATTENTION:
1. Les dommages résultant du non-respect des instructions ou de la modication de lappareil ne sont pas
couverts par la garantie. Tenir loin des enfants et des personnes non-qualiées.
2. L’appareil ne contient aucune pièce remplaçable. Vériez si toutes les pièces sont bien installées et
que les vis sont bien serrées avant la mise en service. Ne pas utiliser lappareil lorsque le boîtier est
ouvert.
REGLES GENERALES:
Ÿ Cet appareil doit être alimenté uniquement en courant alternatif de 230VAC/50Hz et utilisé uniquement
à lintérieur.
Ÿ Utilisez cet appareil uniquement si vous vous êtes familiarisés avec ses fonctions. Ne pas autoriser une
personne inexpérimentée dutiliser cet appareil. La plupart des dommages résultent dune mauvaise
utilisation.
Ÿ Conservez lemballage dorigine pour tout transport.
Pour des raisons de sécurité, il est interdit de modier cet appareil de quelque sorte que ce soit. Toute
manipulation non décrite dans ce manuel peut conduire à des courts-circuits, un choc électrique, une
chute, etc. et invaliderait la garantie.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 14
FI R S T- S e r i e s
C A R AC TE R I STI Q U ES E N C EI NT E S PAS S I VE S
REF.
FIRST-SP08
FIRST-SP10
FIRST-SP12
FIRST-SP15
FIRST-SP215
TYPE
Enceinte passive
large bande à 2
voies 8'' /20cm
Enceinte passive
large bande à 2
voies 10'' /25cm
Enceinte passive
large bande à 2
voies 12'' /30cm
Enceinte passive
large bande à 2
voies 15'' /38cm
Enceinte passive
large bande à 2
voies double 15''
/38cm
Bande passante
(-10dB)
65Hz-20KHz
55Hz-20KHz
50Hz-20KHz
45Hz-20KHz
45Hz-20KHz
Sensibilité
(1W@1M)
96dB
97dB
98dB
99dB
101dB
Puissance (RMS)
150 watts
200 watts
250 watts
300 watts
600 watts
Impédance nom.
8 ohms
8 ohms
8 ohms
8 ohms
4 ohms
Driver
LF 8'' boomer, 2''
VC, 30 OZ
LF 10'' boomer, 2''
VC, 30 OZ
LF 12'' boomer,
2.5'' VC, 50 OZ
LF 15'' boomer, 3''
VC, 60 OZ
LF 15'' boomer, 3''
VC, 60 OZ
HF 1'' moteur à
compression
HF 1.35'' moteur à
compression
HF 1.35'' moteur à
compression
HF 1.75'' moteur à
compression
HF 1.75'' moteur à
compression
Grille
Grille acier avec
tissu acoustique
Grille acier avec
tissu acoustique
Grille acier avec
tissu acoustique
Grille acier avec
tissu acoustique
Grille acier avec
tissu acoustique
Caisson
15mm Multiplex
15mm Multiplex
15mm Multiplex
15mm Multiplex
15mm Multiplex
Finition
Peinture à texture
Peinture à texture
Peinture à texture
Peinture à texture
Peinture à texture
Dimensions
(W x H x D)
300x330x490mm
350x380x585mm
410x430x670mm
475x500x750mm
485x530x1180mm
Poids net
9.70kg
13.60kg
18.50kg
23.50kg
37.20kg
REF.
FIRST-SP12S
FIRST-SP15S
FIRST-SP18S
TYPE
12'' Bass reex subwoofer,
passif
15'' Bass reex subwoofer,
passif
18'' Bass reex subwoofer,
passif
Bande passante (-10dB)
40Hz-160Hz
35Hz-160Hz
30Hz-160Hz
Sensibilité (1W@1M)
100dB
102dB
102dB
Puissance (RMS)
400 watts
500 watts
600 watts
Impédance nom.
8 ohms
8 ohms
8 ohms
Driver
LF 12'' subwoofer, 3'' VC, 80
OZ
LF 15'' subwoofer, 4'' VC,
125 OZ
LF 18'' subwoofer, 4'' VC,
125 OZ
Grille
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Caisson
15mm Multiplex
15mm Multiplex
18mm Multiplex
Finition
Peinture à texture
Peinture à texture
Peinture à texture
Dimensions (W x H x D)
420x510x520mm
490x600x610mm
580x700x715mm
Poids net
21.50kg
31.50kg
44.50kg
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 15
FI R S T- S e r i e s
C A R AC TE R I STI Q U ES – ACT I V ES L A R GE B AN D E
REF
FIRST-SA10DSP2
FIRST-SA12DSP2
FIRST-SA15DSP2
FIRST-SA215DSP2
TYPE
10'' Enceinte 2 voies
large bande, active
12'' Enceinte 2 voies
large bande, active
15'' Enceinte 2 voies
large bande, active
Double15'' Enceinte 2
voies large bande,
active
Bande passante
(-10dB)
55Hz-20KHz
50Hz-20KHz
45Hz-20KHz
45Hz-20KHz
Sensibilité (1W@1M)
97dB
98dB
99dB
101dB
Puissance (RMS)
200 watts
250 watts
300 watts
600 watts
Impédance nom.
4 ohms
4 ohms
4 ohms
4 ohms
Driver
LF 10'' boomer, 2'' VC,
30 OZ
LF 12'' boomer, 2.5''
VC, 50 OZ
LF 15'' boomer, 3'' VC,
60 OZ
LF 15'' boomer, 3'' VC,
60 OZ
HF 1.35'' moteur à
compression
HF 1.35'' moteur à
compression
HF 1.75'' moteur à
compression
HF 1.75'' moteur à
compression
Grille
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Caisson
15mm Multiplex
15mm Multiplex
15mm Multiplex
15mm Multiplex
Finition
Peinture à texture
Peinture à texture
Peinture à texture
Peinture à texture
Dimensions
(W x H x D)
350x380x585mm
410x430x670mm
475x500x750mm
485x530x1180mm
Poids net
14.50kg
20.00kg
25.00kg
39.00kg
TYPE
Bi-amplié, 2 voies
Bi-amplié, 2 voies
Bi-amplié, 2 voies
Amplicateur
Classe D
LF Classe-D, HF Classe AB
LF Classe-D, HF
Classe AB
Puissance de sortie
LF175W+HF75W
LF300W+HF60W
LF500W+HF80W
DSP
Fréq. échantillonnage
24Bit, 96kHz
Fréq. échantillonnage 24Bit, 96kHz
Fréq. échantillonnage
24Bit, 96kHz
Acheur DSP
/
Oui
Oui
Modes
PA, Monitor, Sub,
Speech
Live, Music, Speech, DJ
Live, Music, Speech,
DJ
Module Bluetooth
Oui
Oui
Oui
Connecteurs
Combo Line/Mic in,
RCA in, Bluetooth in,
XLR Mix out
2xCombo Line/Mic in, Bluetooth in, XLR Mix
out
2xCombo Line/Mic in,
Bluetooth in, XLR Mix
out
Contrôles
2 contrôles de volume
dentrée, contrôle de
volume général
2 contrôles de volume dentrée, contrôle de
volume général/Sélecteur de fonction DSP
2 contrôles de volume
dentrée, contrôle de
volume
général/Sélecteur de
fonction DSP
Eclairage logo
façade
M/A
M/A
M/A
Indicateurs
BT Status, Limit,
Signal, Power, DSP 4
Modes
Limit, Signal, Power
Limit, Signal, Power
Protection
Surchaue,
surcharge, DC,
surtension, basse
tension, soft start
Surchaue, surcharge, DC, surtension, basse
tension, soft start
Surchaue,
surcharge, DC,
surtension, basse
tension, soft start
Refroidissement
Convection
Convection
Convection
Alimentation
220-240Vac 50Hz
220-240Vac 50Hz
220-240Vac 50Hz
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 16
FI R S T- S e r i e s
C A R AC TE R I STI Q U ES – S U B WO OF E R A C T IF
REF
FIRST-SA12SDSP2
FIRST-SA15SDSP2
FIRST-SA18SDSP2
TYPE
12'' Bass reex subwoofer,
actif
15'' Bass reex subwoofer,
actif
18'' Bass reex subwoofer,
actif
Bande passante (-10dB)
40Hz-160Hz
35Hz-160Hz
30Hz-160Hz
Sensibilité (1W@1M)
100dB
102dB
102dB
Puissance (RMS)
400 watts
500 watts
600 watts
Impédance nom.
4 ohms
4 ohms
4 ohms
Driver
LF 12'' subwoofer, 3'' VC, 80
OZ
LF 15'' subwoofer, 4'' VC,
125 OZ
LF 18'' subwoofer, 4'' VC,
125 OZ
Grille
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Grille acier avec tissu
acoustique
Caisson
15mm Multiplex
15mm Multiplex
18mm Multiplex
Finition
Peinture texturée
Peinture texturée
Peinture texturée
Dimensions (W x H x D)
420x510x520mm
490x600x610mm
580x700x715mm
Poids net
23.50kg
33.50kg
46.50kg
TYPE
Active Sub Amp
Active Sub Amp
Active Sub Amp
Amplicateur
Classe D
Classe D
Classe D
Puissance de sortie
400W
500W
600W
DSP
Fréq. échantillonnage 24Bit,
96kHz
Fréq. échantillonnage 24Bit,
96kHz
Fréq. échantillonnage 24Bit,
96kHz
DSP display
Oui
Oui
Oui
Modes
Live, Music, DJ1, DJ2
Live, Music, DJ1, DJ2
Live, Music, DJ1, DJ2
Module Bluetooth
Oui
Oui
Oui
Connecteurs
2x Combo Line/Mic in, XLR
Mix out
2x Combo Line/Mic in, XLR
Mix out
2x Combo Line/Mic in, XLR
Mix out
Contrôles
Contrôle de volume
général/Sélecteur de
fonction DSP
Contrôle de volume
général/Sélecteur de
fonction DSP
Contrôle de volume
général/Sélecteur de
fonction DSP
Eclairage logo façade
M/A
M/A
M/A
Indicateurs
Limit, Signal, Power
Limit, Signal, Power
Limit, Signal, Power
Protection
Surchaue, surcharge, DC,
surtension, basse tension,
soft start
Surchaue, surcharge, DC,
surtension, basse tension,
soft start
Surchaue, surcharge, DC,
surtension, basse tension,
soft start
Refroidissement
Convection
Convection
Convection
Alimentation
220-240Vac 50Hz
220-240Vac 50Hz
220-240Vac 50Hz
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 17
FI R S T- S e r i e s
E N T RE ES
Modèles Large bande
Subwoofer Models
1 3
4
5
6
7
12
11
8
9
10
1 2
3
4
5
6
7
8
9
10
14
13
15
16
1
3
4
5
6
7
8
9
10
1211
1
3
4
5
6
7
8
9
10
12
11
FIRST-SA10DSP2
FIRST-SA12DSP2
FIRST-SA12SDSP2
FIRST-SA15SDSP2
FIRST-SA18SDSP2
FIRST-SA15DSP2
FIRST-SA215DSP2
1. ENTRÉE LIGNE / MICRO
Entrée symétrique pour le branchement de sources de signaux tels que tables de
mixage, instrument ou microphones. Les branchements se font par des connecteurs
Jack stéréo 6,35mm ou XLR.
Contrôle de volume pour ajuster les diérents niveaux dentrée. La position centrale est
neutre (pas datténuation, pas damplication). La zone à gauche de zéro règle les
sources dentrée de niveau ligne et la zone à droite les niveaux des microphones. Ces
réglages existent pour lentrée 1 et lentrée 2.
2. Entrée AUX/BT
Branchez un lecteur CD, un IPhone ou un signal Bluetooth sur lentrée AUX/BT du canal
2.
3. MIX OUT
Cette sortie XLR envoie le mélange des deux signaux dentrée vers une autre enceinte
ou un subwoofer. INPUT LEVEL ajuste le niveau du signal dentrée qui est envoyé vers
la sortie OUTPUT. Les réglages MASTER VOL ou DSP naectent pas la sortie OUTPUT.
4. LIMIT (Limitateur automatique damplitude):
Lorsque le signal audio atteint le seuil dangereux pour les transducteurs, ce circuit
interviendra automatiquement en réduisant le signal pour protéger le haut-parleur et
empêcher la distorsion du son.
L’activation de ces dispositifs de protection est matérialisée par les LED de protection
qui sallument.
5. SIGNAL
La LED Signal matérialise le signal dentrée à la fiche dentrée XLR. Le volume est
déterminé par le contrôle de volume général.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 18
FI R S T- S e r i e s
C O N FI GU R AT IO N D E S ENT R E ES D E L A MPL I F IC AT E UR
6. POWER
Ce voyant indique que le système est sous tension.
7. FRONT LED
Allume/éteint léclairage du logo en façade.
8. INTERRUPTEUR M/A
Noubliez pas de mettre le volume au minimum avant de mettre le système sous tension
9. ENTRÉE DALIMENTATION SECTEUR
Branchez le cordon secteur sur cette Fiche avant de mettre le système sous tension.
10. Fusible
Ne remplacez le fusible que lorsque lappareil est débranché du secteur. Utilisez uniquement des fusibles ayant la
même puissance et ampérage. La valeur du fusible est indiquée à larrière
11. LCD
Contrôle DSM et écran de contrôle.
12. VOLUME GENERAL
Règle le volume général
DSP: Naviguez dans le menu et faites une sélection parmi les choix proposés. Appuyez sur le bouton MASTER VOL
pour accéder au menu DPS.
13. MODES DE FONCTIONNEMENT DU SYSTEME:
PA: Cest le réglage par défaut. Il convient lorsque lenceinte est posée sur un support et fait face au public.
DJ: Ce réglage convient lorsque lenceinte est utilisée uniquement pour un DJ ou travaille avec une application de
lecture DJ et est dirigée vers le public.
Monitor: Utilisez ce réglage lorsque lenceinte est utilisée comme retour de scène et dirigée vers vous.
Speech: Utilisez ce réglage si lenceinte nest utilisée que pour des discours et dirigée vers le public.
14. BLUETOOTH:
Appairage de lenceinte avec un appareil Bluetooth :
A: Lorsque lenceinte est sous tension, appuyez pendant 2 secondes sur le bouton PAIR pour activer la fonction
Bluetooth. La ED dappairage clignote.
B: Activez la recherche Bluetooth sur votre appareil et sélectionnez BST-FIRST. Si les deux appareils sont
synchronisés, la LED dappairage reste allumée.
C: Réglez le volume de votre appareil Bluetooth au plus bas.
D: Passez un morceau de musique sur votre appareil Bluetooth et réglez le volume de votre appareil Bluetooth au
maximum.
E: Lorsque votre appareil est synchronisé avec lenceinte, lenceinte reconnaîtra lappareil. Pour le reconnecter, aller
sur la page Bluetooth de votre appareil et cliquez sur « Connecter » pour rétablir la connexion.
F: Pendant la lecture de lappareil Bluetooth, appuyez sur la touche PAIR pour basculer entre lecture et pause. Si
vous appuyez sur la touche PAIR pendant 2 secondes, lappareil se déconnecte et le Bluetooth séteint.
15.VOLUME BLUETOOTH
Tournez ce bouton pour régler le volume dentrée de votre appareil Bluetooth appairé.
16.SELECTEUR MIX OUT
En position haute (Ch1), le niveau MIX OUT ne sera pas aecté par les contrôles de volume dentrée.
En position basse (MIX), le niveau MIX OUT est réglable par les contrôles de volume dentrée.
©Copyright LOTRONIC 2018
www.bst-dj.com
Page 19
FI R S T- S e r i e s
C O N TR OL E D S P
Un menu DSP intégré permet à lutilisateur de sélectionner de nombreuses fonctions.
Pour accéder au menu de contrôle DSP, procédez de la manière suivante :
1. Appuyez sur le bouton Master Vol pour acher le menu DSP.
2. Naviguez dans les fonctions au moyen du bouton Master Vol.
3. Appuyez sur le bouton Master Vol pour sélectionner la fonction que vous souhaitez modier. Le curseur met en
surbrillance les paramètres sur le côté droit du menu DSP.
4. Naviguez dans les fonctions au moyen du bouton Master Vol.
5. Appuyez sur le bouton Master Vol pour conrmer les paramètres sélectionnés.
Le réglage est sauvegardé. Le curseur revient sur les fonctions sur la gauche du menu DSP.
6. Répétez les étapes 2 à 5 pour changer dautres paramètres du DSP et du système.
7. Sélectionnez EXIT pour revenir à lécran daccueil.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

BST FIRST-SA15DSP2 Le manuel du propriétaire

Catégorie
Subwoofers
Taper
Le manuel du propriétaire