LCD Entertainment Ready
Installation Instructions
CORPORATE HEADQUARTERS
10601 West Belmont Avenue
Franklin Park, Illinois 60131 • U.S.A.
847.288.3300 • FAX: 847.288.3703
800.735.3867 (Toll-free within U.S.A., Canada)
INTERNATIONAL OFFICES
M051-00K71-A002
07/07
1
LIFE FITNESS ASIA PACIFIC LTD
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
FAX: (+852) 2575.6001
LIFE FITNESS ATLANTIC BV
LIFE FITNESS BENELUX
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180.646.666
FAX: (+31) 180.646.699
LIFE FITNESS BENELUX NV
Parc Industriel de Petit-Rechain
4800 Verviers
BELGIUM
Telephone: (+32) 87.300.942
FAX: (+32) 87.300.943
LIFE FITNESS DO BRAZIL
Av. Dr. Dib Sauaia Neto 1478
Alphaville, Barueri, SP
06465-140
BRAZIL
Telephone (+55) 11.4193.8282
FAX: (+55) 11.4193.8283
LIFE FITNESS AUSTRIA
Vertriebs GmbH
Hintschiggasse 1
1100 Vienna
AUSTRIA
Telephone: (+43) 1.61 57 198
FAX: (+43) 1.61 57 198.20
LIFE FITNESS IBERIA
Pol. Ind. Molí dels Frares. c/C, nº 12
08620 Sant Vicenç dels Horts (Barcelona)
España
Telephone: (+34) 93.672.4660
FAX: (+34) 93.672.4670
LIFE FITNESS EUROPE GMBH
Siemensstrasse 3
85716 Unterschleissheim
GERMANY
Telephone: (+49) 89.31 77 51.0
FAX: (+49) 89.31 77 51.99
LIFE FITNESS ITALIA S.R.L.
Via San Pieretto
37010 AFFI (Verona)
ITALY
Telephone: (+39) 045.7238204
FAX: (+39) 045.7238197
LIFE FITNESS LATIN AMERICA
and CARIBBEAN
10601 West Belmont Avenue
Franklin Park, Illinois 60131
U.S.A.
Telephone: (+1) 847.288.3300
FAX:(+1) 847.288.3762
LIFE FITNESS UK LTD
Queen Adelaide
Ely, Cambs CB7 4UB
UNITED KINGDOM
Telephone: (+44) 1.353.666 017
FAX: (+44) 1.353.666 018
LIFE FITNESS JAPAN
Nippon Brunswick Bldg., #8F
5-27-7 Sendagaya
Shibuya-Ku, Tokyo
Japan 151-0051
Telephone: (+81) 3.3359.4309
FAX: (+81) 3.3359.4307
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference with radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antennas.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications to this equipment could void the
product warranty.
Mise en garde : tout changement ou toute modification de ce matériel peut annuler la garantie
du produit.
Any service, other than cleaning or user maintenance, must be performed by an authorized service representative.
There are no user serviceable parts.
2
TABLE OF CONTENTS
3
Section Description Page
1. Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Models New 95Ti Treadmill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Models 95Li Summit Trainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Models 95Ci, 93C, 90C Upright Exercise Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Models 95Ri, 93R, 90R Recumbent Exercise Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Models 95Si, 93S, 90S Stairclimbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Models 95Xi, 93X, 90X Cross-Trainers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Models 91Ti, 90T Treadmills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Models 97Ti, 95Ti, 93T Treadmills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3. Console Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
© 2007 Life Fitness, a division of Brunswick Corporation. All rights reserved.
• DANGER: To reduce the risk of electrical shock, always unplug this Life Fitness product before cleaning or
attempting any maintenance activity.
• WARNING:To reduce the risk of burns, fire, electric shock, or injury, it is imperative to connect each prod-
uct to a properly grounded electrical outlet.
• WARNING:To prevent injury, this product must be securely attached in accordance with the installation
instructions.
• Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it has been dropped,
damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services as out-
lined in Service Contacts at the end of this manual.
• Position this product so that the AC power cord plug is accessible to the user.
• Keep the power cord away from heated surfaces. Do not pull the equipment by the power cord or use the cord as a
handle.
• If the electrical supply cord is damaged, it must be replaced by the manufacturer, an authorized service agent, or a
similarly qualified person to avoid a hazard.
• Do not use this product in areas where aerosol spray products are being used or where
oxygen is being administered. Such substances create the danger of combustion and
explosion.
• Always follow the product instructions for proper operation.
• Never insert objects into any opening of the Life Fitness product. If an object should drop inside, unplug this Life
Fitness product and carefully retrieve it while the unit is not in use. If the object cannot be reached, contact Life
Fitness Customer Support Services.
• Do not use this product outdoors, near swimming pools or in areas of high humidity. Do not expose this product to
dripping or splashing liquids .If the product should be exposed to liquid, contact Life Fitness Customer Support
Services.
• Never operate a Life Fitness product with the air openings blocked. Keep air openings free of lint, hair, or any
obstructing material.
• Use this product only for its intended use as described in this manual. Do not use attachments that have not been
recommended by the manufacturer.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
IMPORTANT SAFETY INSTRUCTIONS
4
• DANGER:Pour réduire les risques de décharge électrique, toujours débrancher cet appareil Life Fitness
avant le nettoyage ou toute mesure d'entretien.
•
AVERTISSEMENT: Pour réduire les risques de brûlures, d'incendies, de décharges électriques ou de
blessures, chaque appareil doit absolument être branché sur une prise électrique correctement mise à la terre.
•
AVERTISSEMENTPour prévenir les blessures, ce produit doit être solidement fixé, conformément
aux instructions d'installation.
• Ne jamais faire fonctionner un produit Life Fitness dont la fiche ou le cordon d'alimentation est endommagé, ni
aucun appareil qui serait tombé ou aurait été endommagé ou même partiellement plongé dans l'eau. Si cela se pro-
duit, communiquer avec le service à la clientèle de Life Fitness de la manière indiquée à la rubrique Coordonnées
des réparateurs agréés à la fin du présent guide.
• Placer l'appareil de façon à ce que l'utilisateur ait accès à la fiche du cordon d'alimentation.
• Tenir le cordon d'alimentation à l'écart de toute surface chauffée. Ne pas tirer l'appareil par le cordon d'alimentation;
ne pas utiliser le cordon comme poignée.
• Si le cordon d'alimentation électrique est endommagé, il doit être remplacé par le fabricant, par un réparateur agréé
ou par une personne qualifiée afin d'éviter tout danger.
• Ne pas utiliser ce produit dans des salles où des vaporisateurs aérosols sont employés ou bien où de l'oxygène est
administré. Ces substances créent des risques de combustion et d'explosion.
• Toujours suivre les instructions sur le produit pour s'assurer de son fonctionnement adéquat.
• Ne jamais insérer aucun objet dans les ouvertures du produit Life Fitness. Si un objet tombe à l'intérieur du produit
Life Fitness, le débrancher et extraire l'objet soigneusement pendant que l'appareil est débranché. S'il est impossi-
ble d'atteindre l'objet, communiquer avec le service à la clientèle de Life Fitness.
• Ne pas utiliser ce produit à l'extérieur, près d'une piscine ou dans des endroits très humides. Ne pas exposer ce pro-
duit à des liquides qui s'égouttent ni à des éclaboussures. Si le produit est en contact avec des liquides, communi-
quer avec le service à la clientèle de Life Fitness.
• Ne jamais faire fonctionner d'appareil Life Fitness dont les orifices d'aération seraient bloqués. Les garder exempts
de peluches, de cheveux ou de toute obstruction.
• Utiliser ce produit uniquement pour les fins auxquelles il est destiné et de la manière décrite dans le présent
manuel. Ne pas utiliser d'accessoires qui ne sont pas recommandés par le fabricant.
CONSERVER CES INSTRUCTIONS POUR TOUT USAGE ULTÉRIEUR.
5
CONSIGNES DE SECURITE IMPORTANTES
Note to the CATV Installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the ground-
ing system of the building as close to the point of cable entry as practical.
Antenna Grounding According to the NEC
Antenna Grounding According to the National Electrical Code, ANSI/NFPA 70.
1. Antenna lead in wire
2. Antenna discharge unit (NEC Section 810-20)
3. Grounding conductors (NEC Section 810-21)
4. Ground clamp
5. Power service grounding electrode system (NEC Article 250, Part H)
6. Ground clamp
7. Electric service equipment
REMOTE CONTROL CONFIGURATION
TOOLS REQUIRED: Metric Allen Set
Mount the PIVOT DISC (A) and FRONT BRACKET (B) to the back of the REMOTE CONTROL (C) using
one SCREW (D). Leave the SCREW loose at this time.
Select a user accessible location to mount the REMOTE CONTROL. Position the remote with
bracket at the desired location. Pivot the remote as necessary for optimal user access.
NOTE: If the desired location is such that the BRACKET will not work for mounting,
remove the FRONT BRACKET and reinstall the PIVOT DISC. The remote can now
be installed using the two CABLE TIES (E) or FASTENER DISCS provided with the
REMOTE. Be sure the PIVOT DISC is oriented to accomodate the mounting sur-
face.
Tighten the screw to secure the PIVOT DISC and FRONT BRACKET to the
remote.
Reposition the REMOTE with BRACKET in the desired location and secure the
REMOTE to the equipment using the REAR BRACKET (F) and two SCREWS (G).
Tighten the SCREWS securely.
NOTE: Two differing length of SCREWS (G) are included to accomodate various mounting thicknesses.
NOTE: The REMOTE CABLE (H) can be routed through any of two cable routing channels in the back of the REMOTE or around the
PIVOT DISC.
Recommended Remote Locations:
Product Location Attachment Method
95/97Ti Treadmill Ergobar - far right side Bracket direct to tube
90/91Ti Treadmill Ergobar - far right side Bracket direct to tube
90/93/95Xi Cross-Trainer Aft of water bottle tray - centered Controller mounts to unique bracket
on monocolumn
91X Cross-Trainer Bullhorn near weld to console support tube Bracket direct to tube
- near LEFT side
95Li Summit Trainer Handrail crossbar - near right of water tray Bracket direct to tube
90/93/95Si Stairclimber Handrail crossbar - near left of Polar cover Bracket direct to tube
90/93/95Ci Upright Bike Modified Polar cover w/ holes for Controller mounts to modified Polar
cable ties - centered cover via cable ties
90/93/95Ri Recumbent Bike Front bullhorn handle - right side Bracket direct to tube
INSTALLATION
6
MODELS NEW 95TI TREADMILLS
TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench
PARTS
NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet
1. Turn off the treadmill and unplug it from the power outlet.
2. Remove the six SCREWS securing the MOTOR COVER. Remove the MOTOR COVER and set it
and the screws aside.
3. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener
strip to the bottom of the POWER BLOCK (1). Interlock the remaining FASTENER STRIP to the
installed FASTENER STRIP. Remove the remaining protective liner from FASTENER STRIP and
secure the POWER BLOCK to the FRAME as shown.
4. Plug the POWER CORDS (2) leading from the MOTOR COMPARTMENT and LEFT UPRIGHT
into their respective ends of the POWER BLOCK (1). Feed excess cable into the LEFT UPRIGHT.
5. Re-install the MOTOR COVER using the six previously removed SCREWS.
6. Attach the LOWER MOUNTING BRACKET (3) to the MAIN BRACKET (4) as shown using four
SCREWS (5) and WASHERS (6) each. Tighten the SCREWS securely. (8-10 ft. lbs.)
7. Slide the new BRACKET COVER (7) over the top end of the MAIN BRACKET (4) and down to
meet the LOWER MOUNTING BRACKET (3) as shown.
8. Attach the TV BRACKET (with bent tab) (8) to the MAIN BRACKET (4) as shown using four
SCREWS (5) and WASHERS (6). Tighten the SCREWS securely. (8-10 ft. lbs.)
9. Remove the two SCREWS (9) securing the REAR CONSOLE COVER (10) to the FRAME.
Remove the REAR CONSOLE COVER. Remove the TOP INSERT (11) from the REAR CON-
SOLE COVER and discard. Set the REAR CONSOLE COVER aside.
Achieve Console Units Only:
10. Remove the two SCREWS (--) securing the BOTTOM INSERT (--) and remove the insert. Do not
discard the SCREWS.
11. Locate the REMOTE CONTROL (--) and REMOTE BRACKET (--). Feed the REMOTE CABLE (--
) through the large access hole in the REMOTE BRACKET (--). With the REMOTE CONTROL (-
-) and REMOTE BRACKET (--) oriented as shown, secure them together using one SCREW.
Tighten the SCREW securely.
12. Carefully feed the REMOTE CABLE (--) through the opening in the bottom of the CONSOLE (--
) and through the back of the CONSOLE. Position the REMOTE BRACKET (--) into position
replacing the BOTTOM INSERT (--). Secure the REMOTE BRACKET using the previously
removed SCREWS.
13. Carefully pull the MEDIA CABLE BUNDLE (12) (POWER, COAXIAL, I-R CONTROL
(remote cable on achieve consoles), S-VIDEO) from inside the CONSOLE BRIDGE
(13). Un-bundle and straighten the MEDIA CABLES.
Install the COAXIAL EXTENSION COUPLER and COAXIAL EXTENSION
CABLE.
14. Connect the I-R CONTROL (A) and S-VIDEO (B) CABLES to the back
of the DISPLAY CONSOLE (C).
15. Tape the ends of the all CABLES (POWER, COAXIAL, I-R CONTROL
(remote cable on achieve consoles), S-VIDEO) together.
16. Holding the MAIN BRACKET ASSEMBLY (4) close to the CONSOLE
BRIDGE (13) as shown. With the holes facing upward, feed the taped end of
the MEDIA CABLES (12) through the bottom of the MAIN BRACKET ASSEM-
BLY and out of the UPPER HOLE as shown. Carefully pull excess MEDIA
CABLE through the MAIN BRACKET ASSEMBLY.
17. Slide one GROMMET (14) over the taped end of the MEDIA CABLES (12).
Install the GROMMET into the top access hole.
18. Tilt the MAIN BRACKET ASSEMBLY (4) upward and align the
LOWER MOUNTING BRACKET (3) holes with those in
the CONSOLE BRACKET POSTS. Secure the MAIN
BRACKET ASSEMBLY using four SCREWS (5)
and WASHERS (6). Tighten the SCREWS
securely. (8-10 ft. lbs.)
CAUTION: Raise the BRACKET COVER (7) to meet the
exiting MEDIA CABLES before mounting the MAIN BRACKET
ASSEMBLY.
7
19. With the remaining TV BRACKET (15) oriented as shown, install it to the back of
the TV (16) using four SCREWS (17) and WASHERS (6). Tighten the SCREWS
securely. (8-10 ft. lbs.)
NOTE: Be sure the side holes of the TV BRACKET are oriented as shown.
20. Position the TV BRACKETS (8 & 15) together as shown below and secure
them together using one BOLT (18), WASHER (19) and NUT (20). Leave
the BOLT and NUT loose at this time.
NOTE: Be sure the PIVOT POST of the TV BRACKET (15)
engages onto TV BRACKET (8).
21. Remove the tape from the end of the MEDIA CABLES
(POWER, COAXIAL, I-R CONTROL (remote cable on achieve con-
soles), S-VIDEO)
. Connect all cables to their corresponding
jacks located on the back of the TV (16) (See end of instruc-
tion manual for TV connection details). Feed any excess
MEDIA CABLE into the MAIN BRACKET (4).
22. Install the top MAIN BRACKET CAP (21) to the top of the MAIN BRACKET ASSEMBLY (4).
23. Replace the REAR CONSOLE COVER (10) and secure it using the previously removed two SCREWS (9). Tighten
the SCREWS securely. (8-10 ft. lbs.). Do not over-tighten the SCREWS.
24. Slide the BRACKET COVER (7) down to meet the REAR CONSOLE COVER (10). Snap the BRACKET COVER
into the REAR CONSOLE COVER.
25. Align the LOWEST SIDE HOLES on the TV BRACKETS (8 & 15). Secure the TV BRACKET into proper position
using one SCREW (22) on each side.
NOTE: Life Fitness recommends aligning and securing the TV at the lowest side holes (D) as shown.
26. Plug in the treadmill and power on the treadmill and TV. Refer to the Owners Manual for proper TV setup.
INSTALLATION
8
MODELS NEW 95X CROSS-TRAINERS
TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench
PARTS
NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet
1. Remove the protective liner from one of the provided FASTENER STRIPS.
Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock
the remaining FASTENER STRIP to the installed FASTENER STRIP.
Remove the remaining protective liner from FASTENER STRIP and secure
the POWER BLOCK to the underside of the CENTER FRAME as shown.
Connect the screw-type connector of the POWER CORD (--) to the underside
receptacle. Bundle excess POWER CORD and store under the unit. Connect
the COAXIAL CABLE (r) to the broadcast supply receptacle in similar fashion.
2. Connect the POWER SUPPLY CORD to the POWER ADAPTER (o).
3. Attach the TV BRACKET (with bent tab) (--) to the MAIN BRACKET (--) as shown
using four SCREWS (--) and WASHERS (--). Tighten the SCREWS securely. (8-10 ft.
lbs.)
4. Remove the six SCREWS (--) securing the REAR CON-
SOLE COVER (10) to the FRAME. Remove the REAR
CONSOLE COVER.
Remove the four SCREWS securing the INSERT (--) as
shown. Set the REAR CONSOLE COVER aside.
5. Carefully pull the MEDIA CABLE BUNDLE (--) (POWER
and COAXIAL) from inside the CONSOLE BRIDGE (--). Un-
bundle and straighten the MEDIA CABLES.
Install the COAXIAL EXTENSION COUPLER and COAXIAL
EXTENSION CABLE.
Achieve Console Units Only:
6. Remove the two SCREWS (--) securing the BOTTOM
INSERT (--) and remove the insert. Do not discard the
SCREWS.
7. Locate the REMOTE CONTROL (--) and REMOTE BRACKET (--). Feed the REMOTE
CABLE (--) through the large access hole in the REMOTE BRACKET (--). With the REMOTE
CONTROL (--) and REMOTE BRACKET (--) oriented as shown, secure them together
using one SCREW. Tighten the SCREW securely.
8. Carefully feed the REMOTE CABLE (--) through the opening in the bottom of the
CONSOLE (--) and through the back of the CONSOLE. Position the REMOTE
BRACKET (--) into position replacing the BOTTOM INSERT (--). Secure the
REMOTE BRACKET using the previously removed SCREWS.
9
8
6
5
4
9. Tilt the DISPLAY CONSOLE (--) forward and connect the I-R
CONTROL (A) and S-VIDEO (--) CABLES to the back of the DIS-
PLAY CONSOLE.
10. Tape the ends of the all CABLES (POWER, COAXIAL, I-R
CONTROL, S-VIDEO) together.
11. Feed the taped end of the MEDIA CABLES (--) through the large
hole in the back of the CONSOLE BRACKET (--). Carefully pull
excess MEDIA CABLE through the CONSOLE BRACKET .
12. Slide one GROMMET (--) over the taped end of the MEDIA
CABLES (--).
13. Holding the MAIN BRACKET ASSEMBLY (--) close to the CONSOLE
BRIDGE (--) as shown. With the holes facing upward, feed the taped
end of the MEDIA CABLES (--) through the BOTTOM LARGE HOLE of
the MAIN BRACKET ASSEMBLY and out of the UPPER HOLE as shown.
Carefully pull excess MEDIA CABLE through the MAIN BRACKET ASSEMBLY.
14. Slide the remaining GROMMET (--) over the taped end of the MEDIA CABLES (--).
Install the GROMMETS into the ACCESS HOLES.
15. Secure the MAIN BRACKET ASSEMBLY using four SCREWS (--) and WASHERS (--)
as shown. Tighten the SCREWS securely. (8-10 ft. lbs.)
16. Install the MAIN BRACKET CAPS (--) to the top and bottom of the MAIN BRACKET
ASSEMBLY (--).
17. With the remaining TV BRACKET (--) oriented as shown, install it to the back of
the TV (--) using four SCREWS (--) and WASHERS (--). Tighten the SCREWS
securely. (8-10 ft. lbs.)
NOTE: Be sure the side holes of the TV BRACKET are oriented as
shown.
18. Position the TV BRACKETS (-- & --) together as shown below and
secure them together using one BOLT (--), WASHER (--) and NUT
(--). Leave the BOLT and NUT loose at this time.
NOTE: Be sure the PIVOT POST of the TV BRACKET (--)
engages onto TV BRACKET (--).
19. Remove the tape from the end of the MEDIA CABLES (POWER,
COAXIAL, I-R CONTROL, S-VIDEO). Connect all cables to their
corresponding jacks located on the back of the TV (--) (See end of
instruction manual for TV connection details). Feed any excess
MEDIA CABLE into the MAIN BRACKET (--).
20. Tilt the DOSPLAY CONSOLE back into place. Replace the REAR
CONSOLE COVER (--) and secure it using the previously
removed six SCREWS (--). Tighten the SCREWS securely. (8-
10 ft. lbs.). Do not over-tighten the SCREWS.
21. Align the LOWEST SIDE HOLES on the TV BRACKETS (--
& --). Secure the TV BRACKET into proper position using
one SCREW (--) on each side.
NOTE: Life Fitness recommends aligning and securing
the TV at the lowest side holes ???? (--) as shown.
22. Plug in and power on the TV. Refer to the Owners
Manual for proper TV setup.
INSTALLATION
10
MODELS NEW 95C UPRIGHT LIFECYCLE
®
EXERCISE BIKES
TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench
PARTS
NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet
1. Remove the protective liner from one of the provided FASTENER
STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (--
). Interlock the remaining FASTENER STRIP to the installed FASTENER
STRIP. Remove the remaining protective liner from FASTENER STRIP
and secure the POWER BLOCK to the underside of the CENTER
FRAME as shown.
Connect the screw-type connector of the POWER CORD (--) to the
underside receptacle. Bundle excess POWER CORD and store under
the unit. Connect the COAXIAL CABLE (r) to the broadcast supply
receptacle in similar fashion.
2. Connect the POWER SUPPLY CORD to the POWER ADAPTER (o).
3. Attach the TV BRACKET (with bent tab) (--) to the MAIN BRACKET (--)
as shown using four SCREWS (--) and WASHERS (--). Tighten the
SCREWS securely. (8-10 ft. lbs.)
4. Remove the six SCREWS (--) securing the REAR CONSOLE COVER (10)
to the FRAME. Remove the REAR CONSOLE COVER.
Remove the four SCREWS securing the INSERT (--) as shown.
Set the REAR CONSOLE COVER aside.
5. Carefully pull the MEDIA CABLE BUNDLE (--) (POWER and
COAXIAL) from inside the CONSOLE BRIDGE (--). Un-bundle
and straighten the MEDIA CABLES.
Install the COAXIAL EXTENSION COUPLER and COAXIAL
EXTENSION CABLE.
Achieve Console Units Only:
6. Remove the two SCREWS (--) securing the BOTTOM INSERT (--
) and remove the insert. Do not discard the SCREWS.
7. Locate the REMOTE CONTROL (--) and REMOTE BRACKET (--). Feed the REMOTE
CABLE (--) through the large access hole in the REMOTE BRACKET (--). With the
REMOTE CONTROL (--) and REMOTE BRACKET (--) oriented as shown, secure them
together using one SCREW. Tighten the SCREW securely.
8. Carefully feed the REMOTE CABLE (--) through the opening in the bottom of the
CONSOLE (--) and through the back of the CONSOLE. Position the REMOTE
BRACKET (--) into position replacing the BOTTOM INSERT (--). Secure
the REMOTE BRACKET using the previously removed SCREWS.
11
J
J
J
J J
8
6
5
4
A
A
A
A
A
A
9. Tilt the DISPLAY CONSOLE (--) forward and connect
the I-R CONTROL (A) and S-VIDEO (--) CABLES to
the back of the DISPLAY CONSOLE.
10. Tape the ends of the all CABLES (POWER,
COAXIAL, I-R CONTROL, S-VIDEO) together.
11. Feed the taped end of the MEDIA CABLES (--)
through the large hole in the back of the CONSOLE
BRACKET (--). Carefully pull excess MEDIA CABLE
through the CONSOLE BRACKET .
12. Slide one GROMMET (--) over the taped end of the
MEDIA CABLES (--).
13. Holding the MAIN BRACKET ASSEMBLY (--) close to the
CONSOLE BRIDGE (--) as shown. With the holes facing
upward, feed the taped end of the MEDIA CABLES (--)
through the BOTTOM LARGE HOLE of the MAIN BRACK-
ET ASSEMBLY and out of the UPPER HOLE as shown.
Carefully pull excess MEDIA CABLE through the MAIN
BRACKET ASSEMBLY.
14. Slide the remaining GROMMET (--) over the taped end of the MEDIA CABLES (--). Install the
GROMMETS into the ACCESS HOLES.
15. Secure the MAIN BRACKET ASSEMBLY using four SCREWS (--) and WASHERS (--) as
shown. Tighten the SCREWS securely. (8-10 ft. lbs.)
16. Install the MAIN BRACKET CAPS (--) to the top and bottom of the MAIN BRACKET
ASSEMBLY (--).
17. With the remaining TV BRACKET (--) oriented as shown, install it to the back of the
TV (--) using four SCREWS (--) and WASHERS (--). Tighten the SCREWS
securely. (8-10 ft. lbs.)
NOTE: Be sure the side holes of the TV BRACKET are oriented as
shown.
18. Position the TV BRACKETS (-- & --) together as shown below and
secure them together using one BOLT (--), WASHER (--) and NUT (--).
Leave the BOLT and NUT loose at this time.
NOTE: Be sure the PIVOT POST of the TV BRACKET (--) engages onto
TV BRACKET (--).
19. Remove the tape from the end of the MEDIA CABLES (POWER,
COAXIAL, I-R CONTROL, S-VIDEO). Connect all cables to their corre-
sponding jacks located on the back of the TV (--) (See end of instruction man-
ual for TV connection details). Feed any excess MEDIA CABLE into the MAIN
BRACKET (--).
20. Tilt the DOSPLAY CONSOLE back into place. Replace the REAR CONSOLE
COVER (--) and secure it using the previously removed six SCREWS (--).
Tighten the SCREWS securely. (8-10 ft. lbs.). Do not over-tighten the
SCREWS.
21. Align the LOWEST SIDE HOLES on the TV BRACKETS (-- & --).
Secure the TV BRACKET into proper position using one SCREW (--
) on each side.
NOTE: Life Fitness recommends aligning and securing the TV
at the lowest side holes ???? (--) as shown.
22. Plug in and power on the TV. Refer to the Owners
Manual for proper TV setup.
INSTALLATION
12
A
AAA
A A
A
A
A
A
A
A
A
A
A
17
6
15
16
22
4
16
8
D
13
MODELS NEW 95R RECUMBENT LIFECYCLE
®
EXERCISE BIKES
TOOLS REQUIRED: Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench
PARTS
NOT USED FROM KIT: (1) Main Bracket Cap, (1) Grommet
1. Remove the protective liner from one of the provided FASTENER STRIPS.
Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock
the remaining FASTENER STRIP to the installed FASTENER STRIP. Remove
the remaining protective liner from FASTENER STRIP and secure the
POWER BLOCK to the underside of the CENTER FRAME as shown.
Connect the screw-type connector of the POWER CORD (--) to the underside
receptacle. Bundle excess POWER CORD and store under the unit. Connect
the COAXIAL CABLE (r) to the broadcast supply receptacle in similar fashion.
2. Connect the POWER SUPPLY CORD to the POWER
ADAPTER (o).
3. Attach the TV BRACKET (with bent tab) (--) to the MAIN
BRACKET (--) as shown using four SCREWS (--) and
WASHERS (--). Tighten the SCREWS securely. (8-10 ft.
lbs.)
4. Remove the six SCREWS (--) securing the REAR CON-
SOLE COVER (10) to the FRAME. Remove the REAR CON-
SOLE COVER.
Remove the four SCREWS securing the INSERT (--) as shown.
Set the REAR CONSOLE COVER aside.
5. Carefully pull the MEDIA CABLE BUNDLE (--) (POWER and
COAXIAL) from inside the CONSOLE BRIDGE (--). Un-bundle
and straighten the MEDIA CABLES.
Install the COAXIAL EXTENSION COUPLER and COAXIAL
EXTENSION CABLE.
Achieve Console Units Only:
6. Remove the two SCREWS (--) securing the BOTTOM INSERT (--) and remove the insert.
Do not discard the SCREWS.
7. Locate the REMOTE CONTROL (--) and REMOTE BRACKET (--). Feed the REMOTE
CABLE (--) through the large access hole in the REMOTE BRACKET (--). With the
REMOTE CONTROL (--) and REMOTE BRACKET (--) oriented as shown, secure them
together using one SCREW. Tighten the SCREW securely.
8. Carefully feed the REMOTE CABLE (--) through the opening in the bottom of
the CONSOLE (--) and through the back of the CONSOLE. Position the
REMOTE BRACKET (--) into position replacing the BOTTOM INSERT
(--). Secure the REMOTE BRACKET using the previously removed
SCREWS.
J
J
J
J
J
8
6
5
4
A
A
A
A
A
A
INSTALLATION
14
9. Tilt the DISPLAY CONSOLE (--) forward and connect the I-R CON-
TROL (A) and S-VIDEO (--) CABLES to the back of the DIS-
PLAY CONSOLE.
10. Tape the ends of the all CABLES (POWER, COAXIAL, I-R
CONTROL, S-VIDEO) together.
11. Feed the taped end of the MEDIA CABLES (--) through the
large hole in the back of the CONSOLE BRACKET (--).
Carefully pull excess MEDIA CABLE through the CONSOLE
BRACKET .
12. Slide one GROMMET (--) over the taped end of the MEDIA
CABLES (--).
13. Holding the MAIN BRACKET ASSEMBLY (--) close to the CON-
SOLE BRIDGE (--) as shown. With the holes facing upward,
feed the taped end of the MEDIA CABLES (--) through the BOT-
TOM LARGE HOLE of the MAIN BRACKET ASSEMBLY and out
of the UPPER HOLE as shown. Carefully pull excess MEDIA
CABLE through the MAIN BRACKET ASSEMBLY.
14. Slide the remaining GROMMET (--) over the taped end of the MEDIA
CABLES (--). Install the GROMMETS into the ACCESS HOLES.
15. Secure the MAIN BRACKET ASSEMBLY using four SCREWS (--) and WASHERS (--) as
shown. Tighten the SCREWS securely. (8-10 ft. lbs.)
16. Install the MAIN BRACKET CAPS (--) to the top and bottom of the MAIN BRACKET
ASSEMBLY (--).
17. With the remaining TV BRACKET (--) oriented as shown, install it to the back of the
TV (--) using four SCREWS (--) and WASHERS (--). Tighten the SCREWS
securely. (8-10 ft. lbs.)
NOTE: Be sure the side holes of the TV BRACKET are oriented as
shown.
18. Position the TV BRACKETS (-- & --) together as shown below and
secure them together using one BOLT (--), WASHER (--) and NUT (--
). Leave the BOLT and NUT loose at this time.
NOTE: Be sure the PIVOT POST of the TV BRACKET (--) engages
onto TV BRACKET (--).
19. Remove the tape from the end of the MEDIA CABLES (POWER, COAXIAL, I-R
CONTROL, S-VIDEO). Connect all cables to their corresponding jacks located on
the back of the TV (--) (See end of instruction manual for TV connection details).
Feed any excess MEDIA CABLE into the MAIN BRACKET (--).
20. Tilt the DOSPLAY CONSOLE back into place. Replace the
REAR CONSOLE COVER (--) and secure it using the previ-
ously removed six SCREWS (--). Tighten the SCREWS
securely. (8-10 ft. lbs.). Do not over-tighten the SCREWS.
21. Align the LOWEST SIDE HOLES on the TV BRACKETS
(-- & --). Secure the TV BRACKET into proper position
using one SCREW (--) on each side.
NOTE: Life Fitness recommends aligning and securing
the TV at the lowest side holes ???? (--) as shown.
22. Plug in and power on the TV. Refer to the Owners Manual for
proper TV setup.
A
A
A
A
AA
A
A
A
A
A
A
A
A
A
17
6
15
16
22
4
16
8
D
15
MODELS 95LI SUMMIT TRAINER
TOOLS REQUIRED: Metric Hex Key Set, Side Cutters, T-45 Torx Wrench
1. Remove the CONSOLE SUPPORT TOP CAP (a).
2. Remove the two SCREWS (b) securing the CONSOLE SUPPORT COVER (c). Remove
the CONSOLE SUPPORT COVER and set it and the SCREWS aside.
3. Remove the four SCREWS (d) securing the DISPLAY CONSOLE (e). Set
the SCREWS aside. Tilt the CONSOLE forward and disconnect all
cables. Set the CONSOLE aside.
4. Locate the REMOTE CONTROL (f). Configure the MOUNTING
BRACKET (g) for a vertical installation. Secure the REMOTE CON-
TROL to the top of the HANDRAIL (h) and just left of the RIGHT
BULLHORN (j) as shown. Tighten the BRACKET MOUNTING
SCREWS securely.
5. Route the REMOTE CABLE (k) below the HANDRAIL (h) , around the
MONOCOLUMN (m) and up through the CONSOLE SUPPORT (n) along-
side the POWER CORD and COAXIAL CABLE.
6. Locate the TV MOUNTING BRACKET (o). With the mounting holes in
the tube facing downward, slide the tube portion of the MOUNTING
BRACKET into the top of the CONSOLE SUPPORT (n). Align the
inserts in the tube with the mouting holes on the underside of the
CONSOLE SUPPORT. Secure the MOUNTING BRACKET using two
SCREWS (p). Tighten the SCREWS securely.
CAUTION: Do not pinch and cables when inserting the MOUNTING BRACKET
into the CONSOLE SUPPORT.
7. Re-install the DISPLAY CONSOLE (e) using the four previously removed SCREWS (d). Tighten the SCREWS to 6-8
in-lbs. Do not overtighten the SCREWS.
CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE to the CONSOLE SUPPORT.
8. Attach the ADAPTER BRACKET (q) to the ENTERTAINMENT CONSOLE (r) using four SCREWS (s). Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE (t) using four SCREWS (u) and
WASHERS (v). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
9. Connect the COAXIAL CABLE, POWER CORD and REMOTE CABLE (k) to the rear of the ENTERTAINMENT
CONSOLE (r) as shown under Console Cable Connections at the end of this manual.
10. CABLE TIE (w) any excess cable together behind the ENTERTAINMENT CONSOLE (r) and position the cables
between the MOUNTING BRACKET (o) and the DISPLAY CONSOLE (e).
11. Re-install the CONSOLE SUPPORT COVER (c) and secure it using the two previously removed SCREWS (b).
12. Locate the NEW TOP CAP (x). Place the NEW TOP CAP into position at the top
of the CONSOLE SUPPORT COVER (c). Be sure the TOP CAP snaps securely
in place.
13. Secure the POWER ADAPTER (y) to the FRONT STABILIZER (z) using
two CABLE TIES (w) as shown. Be sure the CABLE TIES are pulled
tight and trim the excess CABLE TIES. Connect the screw-type con-
nector of the POWER CORD (aa) to the frontside receptacle. Bundle
excess POWER CORD and store under the unit. Connect the COAXIAL
CABLE (bb) to the broadcast supply cable in similar fashion.
14. Connect the POWER SUPPLY CORD to the POWER ADAPTER (y).
INSTALLATION
16
MODELS 95CI, 93C, 90C UPRIGHT LIFECYCLE
®
EXERCISE BIKES
TOOLS REQUIRED: Metric Hex Key Set, Side Cutters
NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as
described in the Assembly Instructions.
1. Locate the SPACER (a). With the SPACER oriented as shown,
feed all the CONSOLE CONNECTORS, POWER CORD, and
COAXIAL CABLE through the large center hole in the SPACER.
Slide the SPACER onto the CONSOLE MOUNTING PLATE ()
making sure the top of the SPACER hooks over the top of the
CONSOLE MOUNTING PLATE. Align the mounting holes of
the SPACER and CONSOLE MOUNTING PLATE. Run the
POWER CORD, and COAXIAL CABLE through the channel
at the top of the SPACER.
2. Locate the MOUNTING BRACKET (b). With the MOUNTING
BRACKET oriented as shown, feed all the CONSOLE CONNEC-
TORS through the large center hole in the MOUNTING BRACKET. Align
the LOCATING TABS (c) of the MOUNTING BRACKET with the tab slots and position the MOUNTING BRACKET
into the center channel of the SPACER. Slide the MOUNTING BRACKET upward until it locks solidly in the SPAC-
ER. Secure the MOUNTING BRACKET to the SPACER using two FLAT HEAD SCREWS (d). Tighten the SCREWS
securely.
3. Locate the REMOTE CONTROL (e). Remove the two HORIZONTAL CABLE TIES (C-H) for a VERTICAL (C-V)
installation.
4. Remove the four SCREWS (2) securing the TOP POLAR COVER (5) to the BOTTOM POLAR COVER (6) and
remove the TOP POLAR COVER. Carefully pull the lead end of each CABLE TIE (C-V) until the receptor end meets
the bottom of the REMOTE CONTROL (e).
5. Locate the provided new TOP POLAR COVER (f) with mount-
ing slots. Feed both lead ends of the CABLE TIES (C-V)
throught the bottom mounting slots of the TOP POLAR COVER
as shown. Loop the lead ends of the CABLE TIES upward
through the top mounting slots. Feed the CABLE TIES through
until the bottom of the REMOTE CONTROL (e) contacts the TOP
POLAR COVER.
6. Feed the lead ends of the CABLE TIES (C-V) through the recep-
tor ends and slowly pull them tight, alternating between the two
CABLE TIES. The remote control should now be snug against the TOP
POLAR COVER (f). Trim the excess length of CABLE TIES.
7. Install the new TOP POLAR COVER (f) to the BOTTOM POLAR COVER (5) using the
four previously removed SCREWS (2).
8. Loop the REMOTE CABLE (g) under the HANDLEBARS (11) and secure it to the top of
the CONSOLE EXTENSION TUBE (h) using one CABLE TIE (j) at the location shown.
9. Install the DISPLAY CONSOLE (4) and ACCESSORY TRAY (3) as instructed in the
Assembly Instructions using the four new 1-1/2" SCREWS () supplied. Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE (4) to the
CONSOLE MOUNTING PLATE (D).
17
10. Attach the ADAPTER BRACKET (AA) to the ENTERTAINMENT
CONSOLE (k) to the using four SCREWS (BB). Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
Attach the ENTERTAINMENT CONSOLE to the UPPER
MOUNTING PLATE (m) using four SCREWS (n) and WASHERS
(o). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the
SCREWS.
11. Connect the COAXIAL CABLE, POWER CORD and REMOTE
CABLE (g) to the rear of the ENTERTAINMENT CONSOLE (k) as
shown under Console Cable Connections at the end of this manual.
12. CABLE TIE (j) any excess cable together behind the ENTERTAINMENT
CONSOLE (k) and position the cables between the MOUNTING BRACKET (b) and the
DISPLAY CONSOLE (4).
13. Secure the POWER ADAPTER (p) to the FRONT STABILIZER (q)
using two CABLE TIES (j) as shown. Be sure the CABLE TIES are
pulled tight and trim the excess CABLE TIES. Connect the screw-type
connector of the POWER CORD (r) to the underside receptacle.
Bundle excess power cord and store under the unit. Connect the COAXI-
AL CABLE (s) to the broadcast supply receptacle in similar fashion.
14. Connect the POWER SUPPLY CORD to the POWER ADAPTER (p).
15. Continue with the remainder of assembly as instructed in the
Assembly Instructions. Plug the POWER SUPPLY CORD into
an electrical outlet upon completion.
INSTALLATION
18
MODELS 95RI, 93R, 90R RECUMBENT LIFECYCLE
®
EXERCISE BIKES
TOOLS REQUIRED: Metric Hex Key Set, Side Cutters
NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the Assembly
Instructions.
1. Locate the SPACER (a). With the SPACER oriented as shown, feed all the
CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE
through the large center hole in the SPACER. Slide the SPACER onto the
CONSOLE MOUNTING PLATE (b) making sure the top of the SPACER
hooks over the top of the CONSOLE MOUNTING PLATE. Align the
mounting holes of the SPACER and CONSOLE MOUNTING PLATE.
Run the POWER CORD, and COAXIAL CABLE through the channel
at the top of the SPACER.
2. Locate the MOUNTING BRACKET (c). With the MOUNTING BRACKET
oriented as shown, feed all the CONSOLE CONNECTORS through the large
center hole in the MOUNTING BRACKET. Align the LOCATING TABS (d) of the MOUNTING BRACKET with the tab
slots and position the MOUNTING BRACKET into the center channel of the SPACER. Slide the MOUNTING
BRACKET upward until it locks solidly in the SPACER. Secure the MOUNTING BRACKET to the SPACER using
two FLAT HEAD SCREWS (e). Tighten the SCREWS securely.
3. Locate the REMOTE CONTROL (f). Configure the REMOTE CONTROL for a VERTICAL
(C-V) installation. Secure the REMOTE CONTROL to the top of the HANDLEBAR (g) as
shown. Be sure the CABLE TIES (C-V) are pulled tight and trim the excess CABLE
TIES.
4. Loop the REMOTE CABLE (h) under the HANDLEBAR (g) and secure it to the HAN-
DLEBAR using three CABLE TIES (j) at the locations shown.
5. Install the DISPLAY CONSOLE (7) as instructed in the Assembly Instructions using the four
new 1-1/2" SCREWS supplied. Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the
SCREWS.
CAUTION: Do not pinch any wires when assembling the DISPLAY CONSOLE (7) to the CONSOLE MOUNTING
PLATE (b).
6. Attach the ADAPTER BRACKET (AA) to the ENTERTAINMENT
CONSOLE (k) to the using four SCREWS (BB). Tighten the
SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.
Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNT-
ING PLATE (m) using four SCREWS (n) and WASHERS (o).
Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the
SCREWS.
7. Connect the COAXIAL CABLE, POWER CORD and REMOTE
CABLE (h) to the rear of the ENTERTAINMENT CONSOLE (k) as
shown under Console Cable Connections at the end of this manual.
8. CABLE TIE (j) any excess cable together behind the ENTERTAINMENT
CONSOLE (k) and position the cables between the MOUNTING BRACKET
(c) and the DISPLAY CONSOLE (7).
9. Secure the POWER ADAPTER (p) to the FRONT STABILIZER (q) using two CABLE TIES
(j) as shown. Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES.
Connect the screw-type connector of the POWER CORD (r) to the underside receptacle.
Bundle excess power cord and store under the unit. Connect the COAXIAL CABLE (s) to
the broadcast supply receptacle in similar fashion.
10. Connect the POWER SUPPLY CORD to the POWER ADAPTER (p).
11. Continue with the remainder of assembly as instructed in the Assembly Instructions.
Plug the POWER SUPPLY CORD into an electrical outlet upon completion.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
dans d''autres langues
- English: Life Fitness 90R User manual
Documents connexes
-
Life Fitness T30 Manuel utilisateur
-
-
-
-
-
Life Fitness Fitness Equipment 95XE Manuel utilisateur
-
-
-
Autres documents
-
Landice 90 Series L10 Guide d'installation
-
SportsArt T676 Le manuel du propriétaire
-
NAD M17 Manuel utilisateur
-
-
-
-
Miller JF885933 Le manuel du propriétaire
-
-
Lifefitness SMARTconnect RF Module Manuel utilisateur
-
Cisco MV93X-HW Guide d'installation