Flotec FPCC5030 Le manuel du propriétaire

Marque: Flotec

Modèle: FPCC5030

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

Pump Activity

Activité de pompe

Actividad de la bomba

System Alert

Alerte du système

Alerta del sistema

AC Power

Courant AC

Charging

Recharge

En carga

Battery Status

État de batterie

Estado de la batería

Alarm Silenced

Alarme arrêtée

Alarma apagada

Test System

Tester

Probar sistema

Silence Alarm

Arrêter l’alarme

Apagar alarma

Light

Lumière

Luz

Circuit Breaker

Disjoncteur

Disyuntor

Pump

Pompe

Bomba

Float Switch

Interrupteur à ﬂotteur

Interruptor del ﬂotador

Power

Courant

Encendido

Reset System

Réinitialise

Restrablecer sistema

OWNER’S MANUAL

Battery Backup System

NOTICE D’UTILISATION

Système de secours à batterie

MANUAL DEL USUARIO

Sistema de batería de respaldo

FPCC5030

Installation/Operation/Parts

For further operating, installation,

or maintenance assistance:

Call 800-365-6832

English ........................... Pages 2-16

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

(800) 365-6832

Français .................... Pages 17-31

Instalación/Operación/Piezas

Para mayor información sobre el

funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 800-365-6832

Español ..................... Paginas 32-46

Device ID Key

Safety 2

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation, operation, and maintenance of the product.

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for one of

the following signal words and be alert to the potential

for personal injury!

indicates a hazard which, if not avoided,

will result in death or serious injury.

indicates a hazard which, if not avoided,

can result in death or serious injury.

indicates a hazard which, if not avoided,

can or may result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Carefully read and follow all safety instructions in this

manual and on pumps.

Keep safety labels in good condition. Replace missing or

damaged safety labels.

Battery acid is corrosive. Do not spill on

skin, clothing, or battery charger. Wear eye and head

protection when working with battery. Connect and

disconnect DC output terminals only after removing the

charger from the AC outlet. Never allow the DC

terminals to touch each other.

Hazardous Voltage. Can cause severe or

fatal electrical shock. Do not plug in or unplug battery

charger while standing on a wet floor or in water. Be sure

one hand is free when plugging in or unplugging charger.

If basement floor is wet, disconnect power to basement

before walking on floor. If shut-off box is in basement,

call electric company or hydro authority to shut-off

service to house, or call your local fire department for

instructions. Remove pump and repair or re place. Failure

to follow this warning can result in fatal electrical shock.

Risk of flooding. Do not run pump dry. To

do so will damage seals and can cause leaking and

property damage.

Risk of electrical shock. Do not lift the

pump by the electrical cord; lift pump only by the

discharge pipe, lifting ring or handle on the pump. Lifting

by the cord can damage the cord.

California Proposition 65 Warning

This product and related accessories contain

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

Know the pump application, limitations, and potential

hazards.

1. Do not use in water with fish present. If any oil leaks

out of the motor it can kill fish.

NOTICE This unit is not designed as a waterfall or

fountain pump, or for applications involving salt

water or brine! Use with waterfalls, fountains, salt

water or brine will void warranty.

2. Disconnect power before servicing.

3. Drain all water from system before servicing.

4. Secure discharge line before starting pump. An

unsecured discharge line will whip, possibly causing

personal injury and/or property damage.

5. Check hoses for weak or worn condition before each

use, making certain that all connections are secure.

6. Periodically inspect sump, pump and system

components. Keep free of debris and foreign objects.

Perform routine maintenance as required.

7. Provide means of pressure relief for pumps whose

discharge line can be shut-off or obstructed. Release

all pressure within system before servicing any

component.

8. Personal Safety:

a. Wear safety glasses at all times when working

with pumps.

b. Keep work area clean, uncluttered and properly

lighted – replace all unused tools and equipment.

c. Keep visitors at a safe distance from work area.

d. Make workshop child-proof – with padlocks,

master switches, and by removing starter keys.

9. Follow local and/or national plumbing and electrical

codes when installing the system. A ground fault

circuit interrupter (GFCI) is recommended for use on

any electrical appliance submerged in water.

10. All wiring should be performed by a qualified

electrician.

11. This equipment is only for use on 115 volt

(single phase) and is equipped with an approved

3-conductor cord and 3-prong, grounding-type plug.

12. Where a 2-prong wall receptacle is encountered, it

must be replaced with properly grounded 3-prong

receptacle installed in accordance with codes and

ordinances that apply.

13. Make certain power source conforms to requirements

of your equipment.

14. Protect electrical cord from sharp objects, hot

surfaces, oil, and chemicals. Avoid kinking

cord. Replace or repair damaged or worn cords

immediately.

15. Do not touch an operating motor. Modern motors

can operate at high temperatures.

16. Pump clear water only with this pump.

17. Pump is permanently lubricated at the factory. Do

not try to lubricate it!

18. This pump is designed for use in a residential sump

only.

GENERAL INFORMATION

The Battery Backup Combo Kit is pre-plumbed up to

the hose and clamp assembly. The system includes the

primary sump pump (PSP), backup sump pump (BSP)

assembly, and vertical ﬂoat switch. The unit is equipped

with two check valves - one for the primary pump and

one for the backup pump.

The battery backup pump is not a substitute for your

primary sump pump. It is designed to temporarily backup

your primary sump pump during a power outage or other

problem which prevents normal operation of the primary

pump. Do not use this system to pump flammable liquids

or chemicals. Pump clear sump water only with this

pump. For residential use only.

Keep the battery charger dry and protected from damage.

This system is designed to work with either a sealed

lead-acid AGM battery or a flooded lead-acid battery.

Use of a true Gel Cell (often confused for AGM) or a

standard automotive battery with this charger is not

recommended. An automotive battery may require

charging after only 1-2 hours of continuous use, and the

repeated charging cycles may cause early plate failure in

the battery.

Specifications

Maximum vertical pumping distance is 15 feet (4.6M) for

Model FPCC5030.

Power supply required

Primary Sump Pump ............................115V, 60 HZ.

Backup Sump Pump ......................... 12V DC Battery

Liquid Temp. Range .......................32°F to 70°F(0°-21°C)

Individual Branch Circuit Required (min.) ......... 15 Amps

Discharge:

Hose & Clamp Assembly ............1-1/4”Slip / 1-1/2”Slip

Minimum pit diameter ............................................... 14”

Minimum depth ........................................................ 10”

NOTICE Do not reduce size of discharge pipe or hose

below 1-1/4” diameter. If discharge is too small, pump

will overheat and fail prematurely.

NOTICE If a Carbon Monoxide (CO) sensor is installed,

it must be at least 15 feet away from battery charger

in order to avoid nuisance CO alarms. Please refer

to your CO detector’s installation guidelines for more

information.

Performance - PSP

GPH (LPH) at total feet (m) of lift

Series HP

(1.5m)

(3m)

(4.6m)

(6.1m)

MAX.

LIFTr

Capacity Gallons(L)/Hour

Primary

(FPZS50V)

1/2

3660

(13855)

3000

(11356)

2160

(8176)

960

(3634)

22 ft

(6.7m)

Performance - BSP

GPH (LPH) at total feet (m) of lift

Series

(0)

(1.5m)

(3m)

(4.3m)

MAX.

LIFT

Capacity Gallons(L)/Hour

Backup

(PS17-2005)

2700

(10221)

2040

(7722)

1260

(4770)

360

(1363)

(4.6m)

Electrical & Switch Specifications

Series HP

Motor

Full Load

Amps

Branch

Circuit

Req.

(Amps)

Switch Setting in

inches (cm)

On Off

FPZS50V 1/2 4.1

7.5

19.1)

(7.6)

PS17-2005 - -

10.5

(26.7)

10.19

(25.9)

Required Battery Capacity:

For best results, use the following AGM Storage Batteries:

Part Amp-Hour

Gal/Charge

at 10’

Approx Run

Time

BAT40 40 4,800 5 Hours

BAT75 75 11,500 11.5 Hours

• Unit equipped with dual battery capability

• Maximum amp-hour: 120

• 38-120 Ampere-Hour Storage or Deep Cycle Battery

Safety • Specifications 3

Backup Assembly Installation

Attach backup pump assembly to primary pump. To do

so, un-screw bottom nut on check valve and remove

rubber seal. Place nut from check valve around discharge

PVC pipe on primary pump, then place rubber seal.

Attach backup pump assembly to the primary pump by

tightening nut to the rest of the check valve unit.

Adjust backup pump to sit at an angle (approx. 10°).

Float Switch Installation

Assemble float switch as shown.

Combo Unit Installation

Suggested Materials Needed:

Screwdriver, tape measure, hacksaw, cable ties

1. Drain the sump pit as far as possible without running

the pump dry. Do this by:

A. Piggyback switch: Unplug the pump and switch

from the outlet, then unplug the pump from the

piggyback switch. Reset the circuit breaker or

reinstall the fuse and plug the pump directly into

the outlet. The pump will start. Drain the pit and

unplug the pump. OR

b. No piggyback switch: Reset the circuit breaker

or reinstall the fuse and use a non-conducting

broom handle or stick to raise the float switch;

the pump should start. Drain the pit and then

release the switch.

When the pit has drained, turn off (open) the circuit

breaker or remove the fuse again to avoid electrical

shock while working on the installation.

Unplug existing sump pump and place power cord

and piggyback switch out of the way of work and

water.

2. Measure height of FPCC5030 Combo Kit from base

to top of hose clamp assembly. Subtract 1”.

Drop the tape measure into the bottom of sump pit

and mark the cut line on the discharge pipe (1” less

than total height of the Combo Kit).

3. Use hacksaw to cut horizontally along cut line com-

pletely through pipe.

NOTICE Depending on where your current check

valve is located, there may be excess water. Let the

water drain/drip into the sump pit.

4. Remove old sump from sump pit.

NOTICE Remove all sand, clay, and gravel before

installing.

5. Place Combo Kit into sump pit. Make sure vertical

ﬂoat switches can operate freely inside sump pit.

Pump Installation 4

4827 0916c

(10° angle)

6. Once the Combo Kit is ﬁrmly seated in the base of the

pit, connect the hose and clamp switch to the existing

discharge pipe and clamp it securely.

7. Secure power cord (PSP & BSP), piggyback switch,

and reed switch cord high up and around pipe with

a cable tie. Plug the primary pump into a standard

household 15 amp outlet.

NOTICE The circuit should be dedicated to the sump

pump exclusively.

Remember: Do not handle the pump while it is

plugged in; whether it is running or not.

8. Connect BBU. See “BBU Wiring and Setup”.

9. Once all wiring is complete, ﬁll your pit with water

and verify that the PSP removes the water and the

BBU doesn’t run. Then, unplug your PSP and reﬁll

your pit with water. Verify that the BBU removes the

water.

10. Make sure that the power is on to both pumps, and

your system is ready to use.

Operation

Risk of electric shock. Can shock, burn or kill. Do

not handle a pump or pump motor with wet hands or when

standing on wet or damp surface, or in water.

1. Shaft seal depends on water for lubrication. Do not

operate pump unless it is submerged in water as seal

may be damaged if allowed to run dry.

2. Motor is equipped with automatic reset thermal

protector. If temperature in motor should rise, switch

will cut off all power before damage can be done

to motor. When motor has cooled, switch will reset

automatically and restart motor. If protector trips

repeatedly, pump should be removed and checked.

Low voltage, long extension cords, clogged impeller,

very low head or lift, or a plugged or frozen discharge

pipe, etc., could cause cycling.

3. Pump will not remove all water. If operating a pump

manually and suddenly no water comes out of the

discharge hose, shut off the unit immediately. The unit

has broken prime due to a very low water level.

Risk of electric shock. Can shock, burn or kill.

Before attempting to check why unit has stopped

operating, disconnect power from unit.

4827 0916d

Installation • Operation 5

6615 0916d

6615 0916c

6831 0513C

BBU Wiring and Setup 6

1. Connect the positive (+) charger/controller lead

wire (red) to the positive (+) battery terminal (red).

Connect the negative (–) charger/controller lead

wire (black) to the negative (–) terminal (black) on

the battery. If you are using two batteries, use the

set of optional terminals and connect the second

battery. Use lead wires (not included) to connect

the positive (+) charger/controller terminal to the

positive (+) battery terminal and the negative (–)

charger/controller terminal to the negative (–) battery

terminal.

2. The backup pump leads are polarity sensitive;

connect the positive pump lead to the terminal

labeled Pump ‘+’ and the negative pump lead to the

terminal labeled Pump ‘–’.

NOTICE If the leads are reversed, the pump will run

backward and not pump water.

3. The float switch leads are not polarity sensitive;

connect the float switch leads to the ‘Float Switch’

tabs on the charger/controller.

4. Test the float and the pump by lifting and holding

the float. The system alert LED will blink while

the float is up. The ‘PUMP STATUS’ LED will light

continuously and the buzzer will beep steadily. The

pump should start after 3 seconds. If the pump does

not run, check all the connections and remake them

as necessary.

5. To stop the pump, lower the float; after 25 seconds

the pump should stop, the ‘PUMP STATUS’ LED

should flash, and the buzzer should beep.

6. With the pump operating, test the ‘SILENCE ALARM’

button; hold for one second; release. The ‘ALARM

SILENCED’ LED should illuminate and the buzzer

should stop sounding. To reset the buzzer (allow it to

sound) and extinguish the ‘ALARM SILENCED’ LED,

press the ‘SILENCE ALARM’ button again for one

second.

Depress the ‘TEST SYSTEM’ button; hold it for one

second; release. The ‘PUMP STATUS’ LED should stop

flashing.

BBU Wiring and Setup 7

NOTICE When the unit is first plugged in, or when it first receives power from the battery, the ‘BATTERY STATUS’ LED

will flash for 3 seconds.

NOTICE To activate any Control Button, press and hold it for 1 second.

LED Display and Control Buttons

NOTICE During normal operation, the flashing

‘PUMP STATUS’ LED indicates that the pump has

run in your absence.

1. Press and hold ‘TEST SYSTEM’ button. All LEDs will

light up, pump will run and buzzer will sound.

Release the button and LEDs should go off, pump

should stop, buzzer should stop.

2. The ‘BATTERY STATUS’ LED indicates the battery

capacity when the A.C. power is off.

A. Continuously ON - the battery voltage is above

10.9 Volts Direct Current (10.9VDC) and

capacity is above 20%.

B. Slow Beep/Slow LED Flash - the battery’s

capacity is between 0 and 20%.

C. Fast Beep/Fast LED Flash - the battery is severely

discharged. The battery will continue to charge

(as long as the 115V AC power to the charger is

on) at the rate of .5 AH until the battery’s charge

is above 20%.

When the first warning occurs (slow beep/slow

flash), you will have approximately 2 hours (or less)

of pump operation left. The actual time of operation

will depend on the condition of the battery and may

be as little as 15 minutes.

3. Connect the Power Supply cable (supplied) to the

Charger/Controller’s Power Input jack.

Battery Requirements 8

BATTERY REQUIREMENTS

Hazardous electric current. Can cause

severe burns and start a fire if the battery terminals are

short circuited. Install the battery in the battery case. To

prevent accidental shorting across battery terminals,

close and latch the battery case securely. Do not leave

the battery uncovered.

Do not allow children to play around the battery

backup system installation.

The performance of your backup sump pump depends on

the battery used with it for power. We recommend using

our BAT40 or BAT75. You can also use a group 24M or

27M Deep Cycle battery. They will provide acceptable

performance and will stand up well to long periods of

little or no use.

This system is designed to work with either a sealed

lead-acid AGM battery or a flooded lead-acid battery.

Use of a true Gell Cell (often confused for AGM) or a

standard automotive battery with this charger is not

recommended. An automotive battery may require

charging after only 1-2 hours of continuous use, and the

repeated charging cycles may cause early plate failure in

the battery.

Use only lead-acid batteries. This unit is not designed to

use with Li-Ion, NiMh, NiCAD, Liquid Polymer, etc.

Use only the recommended battery or one of the same

type and size so it will fit in the battery box (maximum

size: 13” long x 7” wide x 10” tall (330.2mm x 177.8mm

x 254mm) including terminals) and supply enough

voltage for full performance.

BATTERY MAINTENANCE

Severe burn hazard. An acid-filled standard

lead-acid battery contains sulfuric acid. Avoid contact with

skin, eyes or clothing.

NOTICE To protect the battery case from chipping and

gouging, do not let the battery sit on a concrete floor.

Install the battery on a shelf or protective pad (plywood,

2x4s, etc.). Always install the battery in a dry location

that is protected from flooding.

Pre-Qualification Test – 1 and 2

Charger is charging at a very low level to try to bring a

dead battery back to life. If the battery is taking too long,

try resetting the charger once or twice (push the ‘SYSTEM

TEST’ and ‘SILENCE ALARM’ buttons together to reset the

charger).

Special Features:

The charger is equipped with reverse battery, short

circuit, and “runaway charge” protection.

Possible Problems and Remedies

1. Wrong Battery Voltage

Reconnect charger to a 12 volt battery.

2. Reversed Battery Connections

Check all connections. The negative (black) on the

battery must connect to the negative (black) on

the charger, and the positive (red) on the battery

must connect to the positive (red) on the charger.

Reversing the battery connections will cause the

‘SYSTEM ALERT’ and ‘SILENCED AUDIBLE ALARM’

LEDs to flash.

3. Thermal Runaway Condition

“Thermal Runaway” is the technical term for the

condition of the battery when some (or all) of the

cells have deteriorated to the point that they won’t

take a charge. In this case, replace the battery.

4. Charge Time Monitor – 1 and 2

Battery took too long to complete its charge. The

“Charge Time Monitor” will shut down the charger

after 84 hours of continuous charging.

Possible causes are:

A) Pump ran for a long period of time during

charging, or

B) Battery is too large for the charger (including

several batteries connected in a parallel circuit).

Excessive Battery Drain

Pump may have run for a very long time, discharging the

battery. In this case:

1. If 115VAC power is OFF, the charger shuts down

until the power comes back on, but the pump will

run as long as the battery charge lasts. You may need

to replace the battery afterwards.

2. If 115VAC power is ON, the charger/controller

continues to try to charge the battery at a charging

rate of .5 AH until the battery charge is more

than 20%, at which point the charger will resume

charging at a rate of 2 AH.

3. If the pump is running and the AC power is on, you

may need to stop the pump to allow the battery to

charge.

Follow the battery manufacturer’s recommendations for

maintenance and safe use of the battery.

Charger/Controller LED Display 9

LED Operating Code Display

System Operating Condition

CHARGING

BATTERY STATUS

PUMP ACTIVITY

AC POWER

ALARM SILENCED

SYSTEM ALERT

Indicates 115V AC Power is connected / Unit online

NOTICE: All of the situations listed above indicate normal system operation; no action is required.

However, if the BBU pump is running or has run, check the primary pump and actively monitor the

charger status for battery life. Always reset the charger after the pump runs.

During normal system operation, the ‘SYSTEM ALERT’ LED blinks while the float switch is on,

indicating the pump should start within 3 seconds. The “AC POWER” LED is lighted

(solid or blinking) as long as the system is plugged in to an operating AC power circuit.

Indicates Pump is running (continuous LED)

Indicates Audible alarm is switched off

Indicates Battery is charging normally

Indicates Continuous LED: battery charge is above 20%,

system is maintaining charge

Indicates Slow flashing LED: battery charge is below 20%

6790 0313

LED is Flashing (Slow)

LED is OFF

LED is ON Continuously

= =

LED is Flashing (Fast)

Indicates Fast flashing LED: Pump has run

Indicates Fast flashing LED: Battery pre-qualification test is running

Indicates 115V AC Power is connected / Unit offline

NOTE: When the System Alert light IS NOT flashing, refer to Table II. When the System Alert light

IS flashing, refer to Table IV

TABLE II – Operating Code Displays (LEDs Lighted Continuously or Flashing)

TABLE III – LED Function Displays (LEDs Lighted Continuously)

Control LED: Continuous Illumination Indicates Normal Operation:

AC Power AC power is present. Unit is online.

Pump Status

The float switch has been activated. The LED remains on (flashing) after the pump

has stopped. Depress the ‘SYSTEM TEST’ button to reset it.

Silenced Audible Alarm Audible Alarm has been silenced. Press and release the ‘SILENCE ALARM’ button

to reset (activate) the audible alarm and turn OFF the LED.

Charging

Indicates that the battery is charging – see Table II, above.

Battery Status A. Continuous ON - the battery voltage is above 10.9 Volts DC and capacity is

above 20%.

B. Slow Beep/Slow LED Flash - the battery’s capacity is below 20%, and voltage is

between 8.2VDC and 10.9VDC.

C. Fast Beep/Fast LED Flash - the battery has been discharged to less than 8.2VDC.

System Alert Flashing (in unison with the buzzer) indicates that the charger has entered ‘Failure

Mode’. Press the ‘SYSTEM TEST’ and ‘SILENCE ALARM’ buttons to reset it.

NOTICE If the source of the failure is not corrected, the charger will reenter

“Failure Mode”. See Table IV for error code information.

Charger/Controller LED Display 10

NOTE: When the System Alert light IS NOT flashing, refer to Table II. When the System Alert light

IS flashing, refer to Table IV

TABLE IV – Error Code Displays (LEDs Flashing)

TABLE V – Control Button Functions

Control Button: Result of Pushing Button:

System Test Pump starts and all LEDs light up.

Will reset the ‘PUMP ACTIVITY’ LED.

When pushed with the ‘SILENCE ALARM’ button, the Charger/Controller microprocessor resets

and error code resets.

Silence Alarm Toggle; Prevents the audible alarm sounding. Press and release to reset.

Light Toggles the light on the Charger/Controller on and off.

System Reset Press and release ‘TEST SYSTEM’ and ‘SILENCE ALARM’ to reset system.

Battery Backup Internet Connection and

Alerts Conﬁguration

1. Complete the Battery Backup Registration, Internet

Connection and Alert Conﬁguration BEFORE con-

necting the battery and AC power supply to your

BBU.

NOTICE If you have already connected the battery

and AC power supply to the BBU before connecting

to to the internet, complete the device registration

process. Then disconnect the battery and remove the

AC power supply from the BBU panel and gateway

for 2 minutes in order to reset the panel. Resume

with Step 8.

2. Go to mylink2o.com and select “sign up” (or Login if

you have an existing account).

3. Follow the online instructions and enter the required

personal information to create a new user account.

4. Register your device using the Unique Device ID Key

included on the device and your manual cover.

5. The Alerts will use the e-mail(s) and phone number(s)

entered here.

6. Find an open network connection on your internet

router or other hardwired connection (like an internet

switch).

7. Rotate the Gateway antenna up on the gateway. Us-

ing the supplied 1 meter Ethernet cable (or a longer

cable if necessary) Connect the Gateway to the open

internet port.

NOTICE We recommend the use of an uninterrupted

power supply for your internet modem, home router

and the gateway power supply.

8. Connect the Gateway power supply to a 115 VAC

outlet, plug the cord into the back of the Gateway.

• The Gateway will blink red for a few seconds.

• When the LED becomes solid Green or solid

Green with an occasional blink – your Gateway

is communicating with the Link2O server. If not,

refer to Gateway Trouble in the manual.

9. Connect the red positive (+) charger/controller lead

wire to the positive (+) (red) battery terminal. Con-

nect the black negative (-)charger/controller lead wire

to the negative (-) (black) battery terminal.

10. Connect the Charger Power Supply cable (supplied)

to the Charger/Controller’s Power input jack. Plug

the other end into a 115 VAC outlet.

11. Check the AC power LED on the Controller – if it is

solid green the unit is communicating with the WEB

site.

12. Verify the system is operational by pressing the ‘TEST

SYSTEM’ button and observing the test sequence.

13. Test communication by clicking the “Test” icon on

the web page and verify the unit has run the test.

14. Using the drop down menu conﬁgure the desired

method of Alerts you want to receive (Text or E-mail).

15. Alerts can be tested by activating the pump with the

ﬂoat switch.

Link

™

Setup 11

Pump won’t run: Check all the wiring connections.

Check for a low or defective battery.

Check that the automatic switch is free to move up and down.

Press the circuit breaker reset button on the control panel.

Motor hums but pump won’t run: Check for low or defective battery.

Pump runs but pumps very little or no water: Make sure a check valve is installed and functioning between the

primary pump discharge and the Battery Backup wye.

Check for an obstruction in the discharge pipe.

The discharge pipe length and/or height exceeds the capacity of the

pump.

Check for a low or defective battery.

The Positive (+) and negative (–) pump wires are reversed.

Disconnect them and reconnect correctly.

Pump cycles too frequently: The check valve located between the discharge of the primary

pump and the Battery Backup wye is not installed or is not

working properly. Install an auxiliary check valve or replace the

existing check valve as required.

TROUBLESHOOTING - PRIMARY PUMP

Troubleshooting 12

Symptom Possible Cause(s) Corrective Action

Pump won’t

start or run.

Pump is not plugged in. Check and see if pump is plugged into a proper outlet.

Blown fuse. If blown, replace with fuse of proper size.

Low line voltage

If voltage under recommended minimum, check size of wiring from main

switch on property. If OK, contact power company or hydro authority.

Defective motor. Replace pump.

Defective float switch. Replace float switch.

Impeller

If impeller won’t turn, remove lower pump body and locate source of

binding.

Float obstructed Remove obstruction.

Pump starts

and stops too

often.

Backflow of water from piping Install or replace check-valve.

Faulty float switch Replace float switch.

Pump won’t

shut off

Defective float switch Replace float switch.

Restricted discharge (obstacle or ice in

piping)

Remove pump and clean pump and piping.

Float obstructed Remove obstruction.

Restricted intake screen Remove the pump and clean the intake screen and the impeller.

Pump

operates but

delivers little

or no water

Low line voltage

If voltage under recommended minimum, check size of wiring from main

switch on property. If OK, contact power company or hydro authority.

Something caught in impeller Remove the pump and clean out the impeller.

Worn or defective parts or plugged

impeller

Clean impeller if plugged; otherwise replace pump.

Check valve installed without vent

hole.

Drill a 1/16” - 1/8” (1.6mm-3.2mm) dia. hole between pump discharge &

check valve (1-2” above where the discharge pipe screws into the pump

discharge and below the waterline).

Restricted intake screen Remove the pump and clean out the intake screen.

Check valve is installed either

backward or upside down

Be sure check valve is installed correctly.

TROUBLESHOOTING - BACKUP PUMP

IF GATEWAY LED LIGHT IS NOT GREEN (GREEN, SLOW BLINK) FIRST TRY TO “POWER CYCLE” THE GATEWAY

(UNPLUG THE POWER CORD, WAIT 15+ SECONDS, THEN RE-APPLY POWER).

Gateway Status

Indicator (LED Color)

Deﬁnition Action Needed

Green Power on: gateway connected to servers. OK - Connection complete and operational

Green, quick blink Power on: data trafﬁc to servers. OK - Operating, data is moving between BBU and

Server

Green, slow blink

(1-2 blinks per second)

Power on: gateway connected to local router, but

not connected to Internet or servers.

System is online and scanning for destination/server

(add a network switch inline to help deﬁne unit).

Red Power on: gateway has no local connection to

router. The gateway does not "recognize/see" that it

is connected to the router.

Check Ethernet cable connections and/or quality or

cable. Try a different router port. Is the router turned

on.

Red, slow blink

(1-2 blinks per second)

Power on: gateway communicating with router, but

router cannot assign Dynamic Host Conﬁguration

Protocol (DHCP) or Domain Name System (DNS) to

gateway.

Router is not permitting the gateway to access the

internet (add a network switch inline to help deﬁne

unit).

Off Power off or product fault. Check power source, verify power adapter is

functioning. Defective gateway.

Troubleshooting 13

TROUBLESHOOTING - Link

O Gateway

Repair Parts - Primary Pump 14

**If motor fails, replace entire pump.

• Purchase locally

Ref Description Qty FPZS33V

1 Power Cord Assembly 1 PS117-54-TSU

2 2 3/4” x 1 1/2” PVC 1 •

3 Vertical Float Switch Assembly 1 FPS17-66

4 Screw #8-32 x 7/8” 4 •

5 Motor 1 **

6 Upper Volute 1 PS1-327

7 Screw #8-32 x 1/2” 5 •

8 Impeller 1 PS5-286

9 Lower Volute 1 PS1-326

10 Screw #8 x 5/8” coarse thread “Sheet/Metal Screw” 6 •

8 - Gateway kit

6786 0313b

Repair Parts - Battery Backup Unit 15

Key No. Part Description Part Number

1 DC Backup Pump PS17-2005*

2 Float Switch

Switch Bracket

PS17-2003

PS17-2004

3 Charger/Controller PS217-1522

4 Battery Case Base

Battery Case Cover

PS17-2044

PS17-2045

5 AC Adaptor PS17-2008

6 Cable Ties - 11” **

7 Backup Combo Plumbing Kit (with check valves) U137-693

8 Gateway Kit (includes Gateway, Power Supply, 1m RJ45 Cable) U117-1568

* If pump fails, replace entire system.

** Sold separately.

Part Description Part Number

AGM 75A-Hour BAT75

AGM 40A-Hour BAT40

Optional Battery Supplies

Not illustrated, sold separately

Warranty 16

Retain Original Receipt for Warranty Eligibility

Limited Warranty

This Limited Warranty is effective October 1, 2016 and replaces all undated warranties and warranties dated before

October 1, 2016.

FLOTEC warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects in material and

workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within twelve (12) months

from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at FLOTEC’s

option, subject to the terms and conditions set forth herein. Note that this limited warranty applies to manufacturing defects only

and not to ordinary wear and tear. All mechanical devices need periodic parts and service to perform well. This limited warranty

does not cover repair when normal use has exhausted the life of a part or the equipment.

The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibility

is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to repair or

replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed per purchase).

Purchaser pays all removal, installation, labor, shipping, and incidental charges.

For parts or troubleshooting assistance, DO NOT return product to your retail store - contact FLOTEC Customer Service at

800-365-6832.

Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet

where it was purchased immediately after the discovery of any alleged defect. FLOTEC will subsequently take corrective action

as promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after the warranty

expires. Warranty is not transferable and does not apply to products used in commercial/rentalapplications.

Sewage Pumps

DO NOT return a sewage pump (that has been installed) to your retail store. Contact FLOTEC Customer Service. Sewage pumps

that have seen service and been removed carry a contamination hazard with them.

If your sewage pump has failed:

• Wear rubber gloves when handling the pump;

• For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;

• Dispose of the pump according to local disposal ordinances.

Exceptions to the Twelve (12) Month Limited Warranty

Product Warranty Period

FP0F360AC, FP0FDC, FPDM21SA, FPDM21HC 90 days

FP0S1775A, FP0S1790PCA, FP0S2400A, FP0S2450A, FP0S4100X, FP2800DCC, FPCP-20ULST, FPPSS3000, FPSC2150A,

FPSC3150A, FPCI3350, FPCI5050 , FPDC30, FPCC5030

2 Years

4” Submersible Well Pumps, FP0S3200A, FP0S3250A, FP0S6000A, FPSC1725X, FPSC2200A, FPSC2250A, FPSE3601A,

FPPSS5000, FPSC3350A, FPZT7300, FPZT7350, FPZT7450, FPZT7550

3 Years

FP7100 Series Pressure Tanks, E100ELT, E3305TLT, E3375TLT, E5005TLT, E50TLT, E50VLT, E75STVT, E75VLT, FPSC3200A,

FPSC3250A, FPSC4550A, FPSE9000

5 Years

General Terms and Conditions; Limitation of Remedies

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not

apply to the following: (1) acts of God; (2) products which, in FLOTEC’s sole judgment, have been subject to negligence, abuse,

accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation, maintenance or storage; (4)

atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or other foreign materials in the system,

or operation at pressures in excess of recommended maximums.

This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective products.

FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED

WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION

PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an

implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights

and You may also have other rights which vary from state to state.

FLOTEC • 293 Wright Street • Delavan, WI USA 53115

Phone: 800-365-6832 • Fax: 800-526-3757 • www.flotecwater.com

Sécurité 17

Consignes de sécurité importantes

CONSERVER CES DIRECTIVES - Ce manuel contient

des directives importantes devant être respectées lors de

l'installation, de l'utilisation et de l'entretien de ce produit.

Il s'agit du symbole d'alerte à la sécurité. Ce symbole,

lorsqu'il se trouve sur votre pompe ou votre manuel, signale

qu'il faut chercher la présence de l'un de ces mots indicateurs

et être conscient des risques de blessure!

indique un risque qui, s'il n'est pas évité, causera

des blessures graves, voire la mort.

indique un risque qui, s'il n'est pas évité, peut

causer des blessures graves, voire la mort.

indique un risque qui, s'il n'est pas évité, peut

causer des blessures mineures, voire modérées.

AVIS vise des pratiques qui ne concernent pas les blessures.

Lire soigneusement et respecter toutes les consignes de

sécurité contenues dans ce manuel ou placées sur les pompes.

Faire en sorte que les étiquettes de sécurité demeurent en

bon état. Remplacer les étiquettes de sécurité manquantes ou

endommagées.

L'acide de batterie est une matière corrosive.

Ne pas mettre en contact avec la peau, les vêtements ou le

chargeur de batterie. Porter une protection oculaire et à la tête

lorsqu'il est nécessaire de manipuler des batteries. Brancher

et débrancher les bornes de sortie CC uniquement après avoir

débranché le chargeur de la prise CA. Ne jamais laisser les

bornes CC se toucher.

Tension dangereuse. Peut causer des chocs

électriques graves, voire mortels. Ne pas brancher ou

débrancher le chargeur de batterie lorsque vous vous tenez

sur une surface mouillée ou inondée. S'assurer qu'une main

demeure libre au moment de brancher ou de débrancher

le chargeur. Si le plancher du sous-sol est mouillé, couper

l'alimentation électrique vers le sous-sol avant de marcher sur

le plancher. Si la boîte d'arrêt est au sous-sol, communiquer

avec la compagnie d'électricité ou le service d'hydro pour

obtenir une interruption de service vers la maison; il est aussi

possible d'appeler le service local de lutte contre les incendies

pour obtenir des directives. Retirer la pompe et la faire réparer

ou la remplacer. Tout manquement à tenir compte de cet

avertissement peut entraîner un choc électrique mortel.

Risque d'inondation. Ne pas faire fonctionner

la pompe à sec. Ce faisait, les joints de la pompe seront

endommagés, créant potentiellement une fuite et des

dommages à la propriété.

Risque de choc électrique. Ne pas soulever

la pompe par son cordon électrique; plutôt, la soulever par

le tuyau de décharge, l'anneau de levage ou la poignée qui

se trouve dessus. Le cordon pourrait être endommagé s'il est

utilisé pour soulever la pompe.

Avertissement relatif à la Proposition 65 en California

Ce produit, de même que les accessoires qui

y sont associés, contient des produits chimiques considérés

cancérigènes ou pouvant causer des déficiences de naissance

ou autres problèmes reproductifs par l'état de la California.

1. Il est important de connaître les applications, les limites et

les risques inhérents de la pompe.

2. Ne pas utiliser en présence de poissons. Les poissons

pourraient être tués en cas de fuite d'huile du moteur.

AVIS Cette unité n'a pas été conçue pour être utilisée en

tant que pompe pour chute d'eau ou fontaine ni pour les

applications impliquant de l'eau salée ou de la saumure!

La garantie de la pompe sera annulée si elle est utilisée

avec des chutes d'eaux, des fontaines ou en eau salée ou

dans la saumure.

3. Débrancher la source d'alimentation avant de procéder à

des réparations.

4. Drainer toute l'eau qui se trouve dans le système avant de

procéder à des réparations.

5. Fixer la conduite de décharge avant de démarrer la pompe.

Une conduite de décharge qui n'est pas bien fixée peut

agir comme un fouet, ce qui est une source potentielle de

blessures ou de dommages.

6. Vérifier les flexibles pour détecter tout bris ou toute trace

d'usure avant chaque utilisation, tout en s'assurant que les

raccords sont bien en place.

7. Inspecter périodiquement le puisard, la pompe et les

composantes du système. S'assurer qu'il demeure libre

de tous débris et corps étrangers. Exécuter une procédure

d'entretien de routine au besoin.

8. Faire en sorte qu'il y ait un système d'évacuation de la

pression pour les pompes dont la conduite de décharge

est coupée ou obstruée. Libérer la pression accumulée

dans le système avant de procéder à tout service sur une

composante.

9. Sécurité personnelle:

a. Porter des lunettes de protection dès que des travaux

sont effectués sur des pompes.

b. Assurer que la zone de travail est propre, libre de tout

obstacle et bien éclairée - ranger tous les outils et les

équipements qui ne sont pas utilisés.

c. Faire en sorte que les visiteurs demeurent à une

distance sécuritaire de la zone de travail.

d. Créer un atelier à l'épreuve des enfants - par l'ajout de

cadenas, de commutateurs principaux et par le retrait

des clés du démarreur.

10. Suivre les consignes des codes de plomberie et d'électricité

locaux et nationaux au moment d'installer le système. Il

est recommandé d'utiliser un disjoncteur de fuite de terre

(GFCI) avec tout appareil électrique submergé dans l'eau.

11. Tout le câblage devrait être mis en place par un électricien

compétent.

12. Cet équipement est destiné à utilisation avec une source

d'alimentation de 115V (monophasique) uniquement;

ilest doté d'un cordon conducteur à 3 fils et d'une prise

à3 fiches avec mise à la terre.

13. Si la seule prise murale disponible est de type à 2 fiches,

il faut la remplacer par une prise de type à 3 fiches

correctement mise à la terre, conformément aux codes et

ordonnances applicables.

14. Vérifier que la source d'alimentation correspond aux

exigences de votre équipement.

15. Protéger le cordon électrique de tout objet tranchant; le

garder à l'égard des surfaces chaudes, de l'huile et des

produits chimiques. Éviter de tordre le cordon. Remplacer

ou réparer immédiatement un cordon s'il est endommagé

ou usé.

16. Ne pas toucher à un moteur en marche. Les moteurs

modernes peuvent fonctionner à des températures élevées.

17. Ne pomper que de l'eau propre avec cette pompe.

18. La pompe a été lubrifiée de manière permanente en usine.

Ne pas essayer de la lubrifier!

19. Cette pompe a été conçue pour être utilisée dans un

puisard résidentiel uniquement.

RENSEIGNEMENTS GÉNÉRAUX

La plomberie de la trousse combinée de secours à batterie est

mise en place en usine, jusqu'à l'ensemble de flexible et de

collier. Le système comprend la pompe de puisard principale

(PPP), l'ensemble de pompe de puisard de secours (PPS) et

l'interrupteur à flotteur vertical. L'unité est dotée de deux

clapets de non retour; un pour la pompe principale, l'autre

pour la pompe de secours.

La pompe de puisard à batterie de secours ne peut pas se

substituer à votre pompe principale. Elle a été conçue pour

agir en tant que support pour votre pompe principale en cas

de panne d'électricité ou de tout autre problème nuisant

au fonctionnement normal de la pompe primaire. Ne pas

utiliser ce système pour pomper des liquides inflammables

ou des produits chimiques. Ne se servir de cette pompe que

pour pomper de l'eau propre. Pour utilisation résidentielle

uniquement.

Assurer que le chargeur de batterie demeure au sec et bien

protégé contre tout dommage.

Ce système a été conçu pour fonctionner avec une batterie

AGM (plomb-gel et feutre) scellée ou une batterie plomb-

acide à électrolyte liquide. L'utilisation d'une vraie batterie à

électrolyte gélifié (souvent confondue pour une batterie AGM)

ou d'une batterie automobile standard n'est pas recommandée

avec ce chargeur. Il pourrait être nécessaire de laisser recharger

une batterie automobile après seulement 1 ou 2 heures

d'utilisation continue ; les cycles de chargement répétés

pourraient ruiner complètement les plaques de la batterie.

Spécifications

La distance de pompage verticale maximale de la pompe est de

4,6m (15pi), dans le cas du modèle FPCC5030.

Alimentation électrique requise

Pompe de puisard principale .......................... 115V, 60 HZ.

Pompe de puisard de secours .....................Batterie 12VCC

Plage de température des liquides ......... 0° à 21°C (32° à 70°F)

Circuit de division individuel requis (min.) .............. 15ampères

Décharge:

Ensemble de flexible .....................Manchon de 3,17/3,80cm

et de collier .............................................. (1-1/4po/1-1/2po)

Diamètre minimum du puits ......................... 35,56cm (14po)

Profondeur minimum ..................................... 25,40cm (10po)

AVIS: Ne pas réduire la taille du tuyau ou du flexible de

décharge à un diamètre inférieur à 3,17cm (1-1/4po). Si la

décharge est trop étroite, cela peut entraîner la surchauffe et

l'arrêt prématurés de la po mpe.

AVIS: si un détecteur de monoxyde de carbone (CO) est

installé, il doit se trouver à au moins 4,6m (15pi) du chargeur

de batterie, ce afin d'éviter l'occurrence de fausses alarmes. Se

reporter aux directives d'installation du détecteur de CO pour

en apprendre davantage.

Performance - PPP

L/h (Gal/h) à un soulèvement total de xx m (pi)

Série HP

1,5 m

(5)

3 m

(10)

4,6 m

(15)

6,1 m

(20)

SOULÈVE-

MENT

MAX

Capacité en L/h (Gal/h)

Principale

(FPZS50V)

1/2

13855

(3660)

11356

(3000)

8176

(2160)

3634

(960)

6,7m

(22pi)

Performance - PPS

L/h (Gal/h) à un soulèvement total de xx m (pi)

Série

(0)

1,5

(5)

(10)

4,3

(14)

SOULÈVE-

MENT

MAX

Capacité en L/h (Gal/h)

Secours

(PS17-2005)

10221

(2700)

7722

(2040)

4770

(1260)

1363

(360)

4,6

(15)

Spécifications électriques et spécifications

de l'interrupteur

Série HP

Puissance

à pleine

charge

du mo-

teur

Exigence

pour le

circuit de

division

(ampères)

Réglage de

l'interrupteur, en cm

(po)

Position

marche

Position

arrêt

FPZS50V 1/2 4,1

19,1

(7,5)

7,6

(3)

PS17-2005 - -

26,7

(10,5)

25,9

(10,19)

Capacité de batterie requise:

Pour obtenir de meilleurs résultats, se servir des batteries à

stockage AGM suivantes:

Pièce Amp-Heure

Gal/Charge

à 3m

(10pi)

Temps

de fonc-

tionnement

approx

BAT40 40 4 800 5heures

BAT75 75 11 500 11,5heures

• Unité pouvant être équipée d'une batterie double

• Amp-heure maximum: 120

• Batterie à stockage de 38-120ampères-heures ou à

décharge poussée

Sécurité • Spécifications 18

Installation de l'ensemble de secours

Relier l'ensemble de pompe de secours à la pompe principale.

Pour ce faire, il faut dévisser l'écrou inférieur du clapet de non

retour et retirer le joint de caoutchouc. Placer ensuite l'écrou

du clapet de non retour autour du tuyau de PVC de décharge

de la pompe principale et remettre le joint de caoutchouc.

Fixer l'ensemble de pompe de secours à la pompe principale

en resserrant l'écrou sur le reste de l'unité de clapet de non

retour.

Ajuster la pompe de secours pour qu'elle soit installée à un

angle (d'environ 10°).

Installation de l'interrupteur

à flotteur

Monter l'interrupteur à flotteur comme montré.

Installation de l'unité combinée

Matériaux requis suggérés:

Tournevis, ruban à mesurer, scie à métaux, attaches pour câble

1. Vider le puits de puisard aussi profondément que possible

sans que la pompe se mette à fonctionner à vide. Pour ce

faire:

a. Interrupteur de sortie conjointe: débrancher la pompe

et l'interrupteur de la prise puis débrancher la pompe

de l'interrupteur de sortie conjointe. Réinitialiser le

disjoncteur de circuit ou remettre le fusible en place

puis brancher la pompe directement dans la prise. La

pompe va démarrer. Vidanger le puits et débrancher la

pompe. OU

b. Sans interrupteur de sortie conjointe: réinitialiser le

disjoncteur de circuit ou remettre le fusible en place

et se servir d'un manche à balai ou d'un bâton pour

soulever l'interrupteur à flotteur, ce qui devrait faire

fonctionner la pompe. Vidanger le puits puis relâcher

l'interrupteur.

Une fois le puits vidangé, couper (ouvrir) le disjoncteur

de circuit ou enlever le fusible à nouveau pour éviter tout

choc électrique pendant l'installation.

Débrancher la pompe de puisard déjà en place et mettre le

cordon d'alimentation et l'interrupteur à l'écart de l'eau et

de l'espace de travail.

2. Mesurer la hauteur de la trousse combinée FPCC5030,

de la base jusqu'en haut de l'ensemble de flexible et

collier. Soustraire 2,54 cm (1 po). Laisser tomber le ruban

à mesurer jusqu'au fond du puisard et marquer la ligne de

coupe sur le tuyau de décharge 2,54cm - (1 po) de moins

que la hauteur totale de la trousse combinée.

3. Utiliser la scie à métaux pour faire une coupe horizontale

complète du tuyau, à la marque.

4827 0916c

AVIS : Selon la position actuelle du clapet de non retour, il

peut y avoir un excès d'eau. Laisser l'eau s'écouler dans le

trou du puisard.

4. Retirer la pompe de puisard qui était déjà en place dans le

puits.

AVIS : Retirer tout le sable, l'argile et le gravier qui se

trouver dans le puits avant de procéder à l'installation.

5. Mettre la trousse de combinaison dans le puits de puisard.

Vérifier que les interrupteurs à flotteur verticaux peuvent

être actionnés librement dans le puisard.

Installation de la pompe 19

(angle de 10°)

6. Une fois la trousse combinée bien placée au fond du

puisard, brancher le flexible et le collier de l’interrupteur au

tuyau de décharge déjà en place etbien fixer le tout.

4827 0916d

7. Bien fixer le cordon d’alimentation (de la PPP et de la

PPS), l’interrupteur enroulé et le cordon de l’interrupteur à

lames en hauteur et autour du tuyau à l’aide d’une attache

de câble. Brancher la pompe principale dans une prise

domestique normale de 15ampères.

AVIS : Le circuit utilisé devrait être exclusivement dédié au

fonctionnement de la pompe de puisard.

Rappel: ne pas manipuler la pompe pendant qu’elle est

branchée, qu’elle fonctionne ou non.

6615 0916c

8. Brancher le SSB. Se reporter à «Câblage et mise en place

du SSB».

9. Une fois le câblage en place, remplir le puits d'eau et

vérifier que la pompe de puisard principale fonctionne mais

que le SSB ne démarre pas. Ensuite, débrancher la pompe

de puisard principale et remplir le puits d'eau à nouveau.

Vérifier que le SSB parvient à éliminer l'eau.

6615 0916d

10. S'assurer que les deux pompes sont alimentées en

électricité; votre système est maintenant prêt à utiliser.

Fonctionnement

Risque de choc électrique. Possibilité de choc,

de brûlure et même de décès. Ne pas manipuler une pompe

ou le moteur de la pompe pendant que vous avez les mains

humides ou que vous vous tenez sur une surface humide ou

mouillée ou dans l'eau.

1. Le joint de l'arbre du moteur est lubrifié par l'eau. Ne pas

faire fonctionner la pompe lorsqu'elle ne se trouve pas

dans l'eau; cela pourrait endommager le joint si la pompe

fonctionne à sec.

2. Le moteur est doté d'un protecteur thermique à

réinitialisation automatique. En cas de hausse de la

température du moteur, l'interrupteur interrompra

toute arrivée de puissance avant que le moteur ne soit

endommagé. Une fois le moteur refroidi, l'interrupteur est

automatiquement réinitialisé et le moteur redémarre. Si le

dispositif de protection se déclenche à répétition, ilfaut

mettre la pompe hors service et la faire vérifier. Lescycles

de déclenchement peuvent être causés par une faible

tension, des rallonges trop longues, un agitateur obstrué,

une tête ou un soulèvement trop bas, un tuyau de décharge

bouché ou gelé, etc.

3. La pompe ne permettra pas de retirer toute l'eau. Si la

pompe est actionnée manuellement, il faut immédiatement

arrêter l'unité lorsque l'eau cesse de sortir du flexible de

décharge. L'unité a une amorce briséeà cause d'un niveau

d'eau très bas.

Risque de choc électrique. Possibilité de choc,

de brûlure et même de décès. Débrancher l'unité avant de

tenter de découvrir pourquoi elle ne fonctionne plus.

Installation • Fonctionnement 20

La page charge ...

Flotec FPCC5030 Le manuel du propriétaire

Marque: Flotec

Modèle: FPCC5030

Catégorie: Pompes à eau

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Flotec FPCC5030 Owner's manual
español: Flotec FPCC5030 El manual del propietario

Flotec FPCC5030 Le manuel du propriétaire

Flotec FPCC5030 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents