Sony DSR-40 Manuel utilisateur

Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur

Ce manuel convient également à

1999 by Sony Corporation
DSR-40/40P
3-865-349-15(1)
Digital
Videocassette
Recorder
Operating Instructions page 2
GB
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
Mode d’emploi page 2
FR
Avant la mise en service de cet appareil, prière de lire
attentivement ce mode d’emploi que l’on conservera
pour toute référence ultérieure.
GB
FR
DSR-40/40P
2
GB
For DSR-40
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
Note
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Precautions
Safety
• Operate the unit only on 120 V AC, 60 Hz .
• If anything falls into the cabinet, unplug the unit and have it
checked by qualified personnel before operating it any
further.
• Unplug the unit from the wall outlet if you do not intend to
use it for an extended period of time. To disconnect the
cord, pull it out by the plug, never by the cord.
Installing
• Allow adequate air circulation to prevent internal heat
buildup.
• Do not place the unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that may block the
ventilation slots.
• Do not install the unit near heat sources such as radiators
or air ducts, or in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.
• Do not install the unit in an inclined position. It is designed
to be operated in a horizontal position only.
• The unit is not designed for portable use. Install it properly
on a flat stable place. Placing it on its side or on a surface
slanted more than 30 degrees may cause damage.
• Keep the unit and cassettes away from equipment with
strong magnets, such as microwave ovens or large
loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm location,
moisture may condense inside the VCR and cause damage
to the video head and tape. When you first install the unit,
or when you move it from a cold to a warm location, wait for
about one hour before operating the unit.
Information
Compatible color systems
The DSR-40 is designed to record and play back using the
NTSC color system. Recording of video sources based on
other color systems cannot be guaranteed.
Caution
Television programs, films, video tapes and other materials
may be copyrighted. Unauthorized recording of such material
may be contrary to the provisions of the copyright laws. Also,
use of this recorder with cable television transmission may
require authorization from the cable television transmission
and/or program owner.
Owners record
The model number is located at the rear and front of the unit
and the serial number on the top. Record the serial number in
the space provided below. Refer to these numbers whenever
you call upon your Sony dealer regarding this product.
Model No. DSR-40 Serial No. ______________________
3
GB
For the customers in the U.S.A.
Declaration of Conformity
Trade Name: SONY
Model No.: DSR-40
Responsible Party: Sony Electronics Inc.
Address: 1 Sony Drive, Park Ridge,
NJ, 07656 USA
Telephone No.: 201-930-6970
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
For DSR-40P
WARNING
To prevent fire or shock hazard, do not expose the unit to
rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Precautions
Safety
• This unit operates on 220 – 240 V AC, 50 Hz. Check that
the unit’s operating voltage is identical with your local power
supply.
• If anything falls into the cabinet, unplug the unit and have it
checked by qualified personnel before operating it any
further.
• The unit is not disconnected from the mains as long as it is
connected to the mains outlet, even if the unit itself has
been turned off.
• Unplug the unit from the wall outlet if you do not intend to
use it for an extended period of time. To disconnect the
cord, pull it out by the plug, never by the cord.
Installing
• This unit is equipped with a fan at the rear. Do not insert
objects nor touch the fan during operation.
• To prevent internal heat buildup, install the unit at least
5 cm away from the wall, and dust the unit periodically.
• Do not place the unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that may block the
ventilation slots.
• Do not install the unit near heat sources such as radiators
or air ducts, or in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.
• The unit is not designed for portable use. Install it properly
on a flat stable place. Placing it on its side or on a surface
slanted more than 30 degrees may cause damage.
• Keep the unit and cassettes away from equipment with
strong magnets, such as microwave ovens or large
loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm location,
moisture may condense inside the VCR and cause damage
to the video head and tape. When you first install the unit,
or when you move it from a cold to a warm location, wait for
one to two hours before operating the unit.
Caution
Television programmes, films, video tapes and other
materials may be copyrighted. Unauthorised recording of
such material may be contrary to the provisions of the
copyright laws. Also, use of this recorder with cable television
transmission may require authorisation from the cable
television transmitter and/or programme owner.
Compatible colour systems
The DSR-40P is designed to record and play back using the
PAL colour system. Recording of video sources based on
other colour systems cannot be guaranteed.
For the customers in Europe
This product with the CE marking complies with both the
EMC Directive (89/336/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment, ex.
TV studio).
For the customers in the Netherlands
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd. Wanneer deze leeg
zijn, moet u ze niet weggooien
maar inleveren als KCA.
4
GB
Table of Contents
Table of Contents
Chapter 1
Overview
Features .............................................................................6
Notes on Video Cassettes .................................................... 8
Notes on Recording / Playing.............................................. 9
Location and Function of Parts .....................................10
Front Panel ........................................................................ 10
Rear Panel ......................................................................... 14
Chapter 2
Playback and
Recording
Playback...........................................................................16
Connections for Playback.................................................. 16
Settings for Playback......................................................... 18
Playback Procedure ........................................................... 19
Playback Functions ........................................................... 20
Recording ........................................................................23
Connections for Recording................................................ 23
Settings for Recording....................................................... 25
Recording Procedure ......................................................... 27
Chapter 3
Using the Unit as a
Player in an
Editing System
Notes on Usage in the Editing System .........................30
Connections for a Digital Non-linear Editing................32
Connections for a Cut Editing System..........................33
Connections for an A/B Roll Editing System ...............35
Adjusting an Edit Timing ................................................40
Adjusting the Sync and Subcarrier Phases..................44
Adjusting Signals............................................................47
Chapter 4
Using the Unit as a
Recorder in an
Editing System
Using the Unit as a Recorder
with FXE-100/100P/120/120P.................................49
Table of Contents 5
GB
GB
Chapter 5
Menu Settings
Changing Menu Settings ................................................51
Changing the SET UP MENU Settings............................. 51
Menu Contents .................................................................. 51
Recommended settings in the SET UP menu.................... 54
Chapter 6
Maintenance and
Troubleshooting
Alarm Messages..............................................................55
Troubleshooting ..............................................................56
Notes on Use ...................................................................57
Appendix
Specifications..................................................................60
Compatibility of DVCAM and DV Format ......................62
Glossary...........................................................................64
Index.................................................................................66
Features
Chapter 1 Overview
6
GB
Chapter 1 Overview
Features
The DSR-40/40P is a
1
/4-inch digital videocassette
recorder that uses the DVCAM digital recording
format. This system achieves stable, superb picture
quality by digitally processing video signals that are
separated into color difference signals and luminance
signals (component video).
When connected to Sony Edit Station™, the unit
serves as part of powerful non-linear editing system
1)
.
The unit is equipped with a full-fledged analog
interface to support hybrid systems that combine
conventional analog equipment with digital equipment.
The DSR-40/40P’s main features are described below.
DVCAM Format
DVCAM is based on the consumer DV format, which
uses the 4:1:1 component digital format (DSR-40) or
the 4:2:0 format (DSR-40P), and provides a
1
/4-inch
digital recording format for professional use.
High picture quality, high stability
Video signals are separated into color difference
signals and luminance signals, which are encoded and
compressed to one-fifth size before being recorded to
ensure stable and superb picture quality.
Because the recording is digital, multi-generation
dubbing can be performed with virtually no
deterioration of quality.
Wide track pitch
The recording track pitch is 15 µm, fully 50 percent
wider than the DV format’s 10-µm track pitch. Thanks
to this feature, the DVCAM format sufficiently meets
the reliability and precision requirements of
professional editing.
High-quality PCM digital audio
PCM recording makes for a wide dynamic range and a
high signal-to-noise ratio, thereby enhancing sound
quality.
There are two recording modes: 2-channel mode
(48-kHz sampling and 16-bits linear code), which
offers sound quality equivalent to the DAT (Digital
Audio Tape) format, or 4-channel mode (32-kHz
sampling and 12-bits nonlinear code).
Playback compatibility with DV format
A DV cassette recorded on a DV-format VCR can be
played back on this unit. (Cassettes recorded in LP
mode cannot be played back.)
Choice of two cassette sizes
The unit can use both standard-size and mini-size
DVCAM cassettes.
According to cassette size, it automatically changes
the position of the reel drive plate.
The maximum recording/playback times are
184 minutes for standard size cassettes and 40
minutes for mini-size cassettes.
Facilities for High-efficiency
Editing
The unit provides an abundance of functions that
enhance editing efficiency and precision.
Remote control
The unit can be operated by remote control from an
editing controller that supports the RS-422A interface
or from a SIRCS
2)
-system remote control unit such as
the optional DSRM-10, or DSRM-20.
1) Non-linear editing
This is an editing method that uses video and audio
signals that have been digitally encoded and recorded on
a hard disk as digital data. When compared with
conventional (linear) editing methods, non-linear editing
offers vastly improved efficiency in editing operations,
such as by eliminating tape transport time.
........................................................................................................................................................................................................
2) SIRCS (Sony Integrated Remote Control System)
A command protocol to remote control Sony
professional videocassette recorders/players.
Chapter 1 Overview
Chapter 1 Overview 7
GB
Chapter 1 Overview
High-speed search function
If you use the optional remote control unit, the unit has
a picture search function that allows you to view color
picture at playback speeds up to 14 times normal speed
(DSR-40) or 17 times normal speed (DSR-40P) in
forward and reverse directions.
When remote-controlling this unit in shuttle mode
from an editing controller or a remote controller, you
can search at any speed in the range 0 (still) to 14
times normal (DSR-40) or 17 times normal (DSR-40P)
in both directions. You can also search frame-by-
frame in jog mode.
You can also hear playback audio.
Jog audio function
If you use the optional remote control unit, audio can
be monitored at various playback speeds when in jog
mode. The audio signals are once stored in memory
and then played back at the same rate as the search
speed. This allows you to use audio playback to find
the desired edit points.
Other Features
Analog output interfaces
The unit comes with analog output interfaces enabling
it to be connected to analog video and audio
equipment.
Analog video: Include composite video, component
video (Y/R–Y/B–Y), and S-video outputs.
Analog audio: The XLR-type (3-pin) analog audio
outputs are provided.
Power-on playback function (in repeat
playback mode)
You can start playback immediately when the unit
turns on.
Compact size
The unit achieves compact size suitable for using on a
demonstration or a bridal. The unit is also equipped
with basic functions that are needed for videocassette
recorders and players used in professional digital video
editing systems.
Menu system for functionality and
operation settings
The unit provides a menu system to make its various
functions easier to use and set up its operation
conditions.
Superimposition function
Time code, operation mode indications, menus, alarm
messages, and other text data can be superimposed and
output in analog composite video signals.
Easy maintenance function
The unit’s digital hours meter functions include two
kinds of tally operations for head drum usage hours,
and tape threading/unthreading times. The tally results
can be viewed on the video monitor.
Features
Chapter 1 Overview
8
GB
Chapter 1 Overview
DVCAM cassette Mini DVCAM
cassette
Write protected
Write enabled
Notes on Video Cassettes
Usable cassettes
Use Standard-DVCAM cassettes or Mini-DVCAM cassettes with this
VCR. PDV-184ME can record programs for 184 minutes and PDVM-
40ME can record for 40 minutes.
You can get the highest quality pictures with this digital videocassette
recorder using DVCAM cassettes. You may not be able to get as good
quality with other cassettes. We recommend using DVCAM cassettes so
that you can record your one-time events in highest quality.
Cassette memory
Cassette memory is an optional feature that is mounted on some Standard
DVCAM cassettes and Mini DVCAM cassettes. When you record a
program, the recording date and time, and the programs’ position on the
tape are stored in the cassette memory so that you can quickly locate the
program later on.
indicates that you can use the cassettes 16 Kbits
of data can be stored on. On this VCR, you can use the cassettes up to
16 Kbits of data can be mounted on.
To save a recording
To prevent accidental erasure of a recording, slide in the safety switch on
the cassette so that the red portion becomes visible. To record on a tape,
slide out the switch so that the red portion is hidden.
Note
, , and are trademarks.
Chapter 1 Overview
Chapter 1 Overview 9
GB
Reel
Paper clip, etc.
Checking the tape for slack
Using a paper clip or a similar object, turn the reel gently in the direction
shown by the arrow. If the reel does not move, there is no slack. Insert the
cassette into the cassette compartment, and after about 10 seconds take it
out.
Notes on Recording / Playing
Copyright precautions
On recording
You cannot record any software having copyright protection signals on this
VCR. If you start recording protected video and audio signals, a warning
message appears on the monitor screen and the VCR stops recording.
On playback
When you play back software having copyright protection signals on this
VCR, you may not be able to copy it onto other equipment.
Limitations caused by the difference in format
This VCR can record, play back and edit the tapes recorded in DVCAM
format. It can also play back the tapes recorded in DV format (SP mode).
However, due to the difference in format, you may not be able to record or
edit some tapes affected by recording conditions of the tape (e.g., A tape
originally recorded in DV format is dubbed in DVCAM format). For
details, refer to “Compatibility of DVCAM and DV format” on page 62.
No compensation for contents of the recording
Contents of the recording cannot be compensated for if recording or
playback is not made due to a malfunction of the VCR, video tape, etc.
Note
You cannot play back a DVCAM tape recorded in other color systems on
this VCR.
Location and Function of Parts
Chapter 1 Overview
10
GB
Chapter 1 Overview
DUP
INPUT
SELECT
TC
TAPE
REMAIN
COUNTER
COUNTER
SELECT
CH-1/2
CH-3/4
MIX
AUDIO
MONITOR
REPEAT
REC
OFF
TIMER
REMOTE
LOCAL
MENU
SET
7 EJECT button
6 COUNTER RESET
button
2 Tape transport
control section
(see page 12)
3 Inside of the door
(see page 13)
Location and Function of Parts
Front Panel
1 Cassette compartment
Accepts standard-size or mini-size DVCAM digital
videocassettes. When using a mini-size cassette, insert
it into the center of the compartment.
For details of usable cassettes, see page 8.
2 ON/STANDBY switch and ON/STANDBY lamp
Press this switch to turn on the power, and the ON/
STANDBY lamp lights in green. Press it again to turn
to standby mode, and the lamp lights in red.
Note
When the REMOTE/LOCAL switch is set to
REMOTE, you cannot turn the unit to standby mode.
3 PHONES jack (stereo minijack)
Connect stereo headphones for headphone monitoring
during recording or playback.
The audio signal you want to monitor can be selected
with the AUDIO MONITOR selector inside of the
door (3).
4 PHONE LEVEL control knob
Controls the volume of the headphones connected to
the PHONES jack.
5 AUDIO INPUT LEVEL control knobs
When recording, you can use these knobs to set audio
input levels for CH-1 (channel 1) and CH-2 (channel
2), respectively.
6 COUNTER RESET button
Press this button to reset the tape counter in the display
window to “0:00:00 (0
H00M00S)”. This button does not
work when displaying the time code or the remaining
time.
7 EJECT button
Press this button to eject a cassette.
1 Cassette compartment
5 AUDIO INPUT LEVEL control knobs
2 ON/STANDBY switch
and ON/STANDBY lamp
1 Display section
(see page 11)
3 PHONES jack
4 PHONE LEVEL control knob
Chapter 1 Overview
Chapter 1 Overview 11
GB
1 Audio level meter
2 Time counter display
3 Video input signals
indicators
4 NS AUDIO indicator
5 Audio mode indicators
6 TIMER indicator
1 Display section
1 Audio level meter
Indicates the recording level during recording or EE
mode, and the playback level during playback. When
the audio level exceeds 0 dB, the red indicator lights.
Note
If you play back the tape whose audio was only
recorded on channel 2, the audio level meter for CH2/4
may not function.
2 Time counter display
Indicates the following:
Time data: count value of the time counter, time code
and remaining time.
Alarm messages (see page 55).
Messages for self-diagnosis function (see page 59).
Notes
For DSR-40P: Time code is set to the non drop frame
mode only.
Time code is indicated as follows:
Drop frame: “00:00.00:00” (DSR-40 only)
Non drop frame: “00:00:00:00”
3 Video input signals indicators
Indicates the currently selected video input signals.
INPUT VIDEO, INPUT S VIDEO, or INPUT DV
lights.
4 NS (Non Standard) AUDIO indicator
Lights when the VCR plays back a tape whose audio
recording was made in the unlock mode, or when unlock
mode signals are input through the DV jack.
For details of unlock mode, see page 62.
5 Audio mode indicators
Indicates the audio mode during playback or recording
or while in EE mode.
During playback it indicates the audio mode in which
the tape was recorded.
During recording or while in EE mode, it indicates
the currently selected audio recording mode. You can
select audio recording mode by setting “AUDIO
MODE” menu (see page 53).
Fs32k: Lights when playing the tapes recorded in
4-channel mode, or recording a tape in 4-channel
mode.
Fs48k: Lights when playing the tapes recorded in
2-channel mode, or recording a tape in 2-channel
mode.
Note
When recording in 4-channel mode on this VCR, audio
signals are recorded only in channels 1/2.
6 TIMER indicator
Lights when setting the TIMER switch to REPEAT.
7 DVCAM indicator
Lights except playing back the DV-formatted tapes.
8 Cassette indicator
Lights when inserting a digital video cassette available
for this VCR. It flashes when ejecting a cassette.
9 Mini indicator
Lights when inserting mini-size digital video cassette.
CH 1/3 CH 2/4
24
12
6
0
Mini
HOURS MINUTES SECONDS FRAMES
TIMER INPUT DV
S VIDEO
NS AUDIO
Fs32k Fs48k
9 Mini indicator
8 Cassette indicator
7 DVCAM indicator
Location and Function of Parts
Chapter 1 Overview
12
GB
Chapter 1 Overview
4 PAUSE button
1 Tape Transport indicators
2 DUP button
3 REC button
5 F FWD button
6 PLAY button
7 REW button
8 STOP button
2 Tape transport control section
1 Tape Transport indicators
2 DUP (duplicate) button
Use this button to make a work tape having the same
time codes as the source tape.
For details on duplication, see page 28.
3 REC (record) button
When you press the PLAY button while holding down
this button, the indicator lights and recording begins.
To set the VCR to recording pause mode, press the
PAUSE button while holding down this button.
4 PAUSE button
When you press this button, the indicator lights, and
the VCR is set to pause mode.
5 F FWD (fast forward) button
When you press this button, the indicator lights and the
tape is fast forwarded. During fast forward, the picture
does not appear on the monitor (you can see the
picture of the EE mode during fast forward).
To search forward, hold this button down during fast
forward.
6 PLAY button
When you press this button, the indicator lights and
playback begins.
If you press this button while holding down the REW
button during stop, the tape is rewound to its beginning
and starts playing automatically (during rewind, the
REW indicator lights and the PLAY indicator flashes).
7 REW (rewind) button
When you press this button, the indicator lights and the
tape starts rewinding. During rewind, the picture does
not appear on the monitor (you can see the picture of
the EE mode during rewind).
To search backward, hold this button down during
rewind.
If you press the PLAY button while holding down this
button during stop, the tape is rewound to its beginning
and starts playing automatically (during rewind, the
REW indicator lights and the PLAY indicator flashes).
8 STOP button
Press this button to stop the current tape transport
operation.
STOP REW PLAY F FWD PAUSE REC
DUP
DUP
Note
When the tape reaches to its beginning or its end by
rewinding or fast-forwarding, the unit turns to
playback pause mode. Then, the playback pause mode
is released after the time which is set at “STILL
TIMER” menu (See page 52).
Chapter 1 Overview
Chapter 1 Overview 13
GB
9 Arrow (˘ ) buttons
3 Inside of the door
1 INPUT SELECT button
Selects input signals. Each press of this button cycles
through three video signal selection options: video, S-
video, and DV input. When you select one of these
options, the corresponding indicator in the display
lights up.
2 CL (Clear) button
Press this button to make the unit to the state of
reconnecting the AC power cord. When you press this
button, the setting in the menu is not initialized.
3 COUNTER SELECT selector
Select the type of time data in the time counter display.
TC: Time code
COUNTER: Count value of the time counter
TAPE REMAIN: Remaining time
4 AUDIO MONITOR selector
Use to select the audio track you want to hear when
playing back a tape recorded in 4-channel mode
(Fs32k).
CH-1/2: Channels 1/2 only
MIX: Channels 1/2 and channels 3/4 (mix)
CH-3/4: Channels 3/4 only
5 TIMER switch
Use to select Auto Repeat using an external AC timer
(not supplied).
REPEAT: When the power is supplied to this VCR,
a tape rewinds to its beginning automatically and
playback starts. The VCR repeats the playback
from the beginning to the first index (if there is no
index on the tape, to the unrecorded portion; if no
unrecorded portion, to the tape end). Auto repeat
also functions if you set this switch to REPEAT
during playback.
OFF: Auto Repeat is released.
6 REMOTE/LOCAL switch
Selects whether the unit is operated from its front
panel or from external (remote) equipment.
REMOTE : The unit is operated from an editing
controller connected to the REMOTE connector.
Available tape transport buttons (on the front
panel or optional remote control unit) are set in
the menu.
LOCAL : The unit is operated from its front panel,
or from a SIRCS-system remote control unit
connected to the CONTROL S jack.
INPUT
SELECT
TC
CL
TAPE
REMAIN
COUNTER
COUNTER
SELECT
CH-1/2
CH-3/4
MIX
AUDIO
MONITOR
REPEAT
OFF
TIMER
REMOTE
LOCAL
MENU
SET
1 INPUT SELECT button
2 CL button
3 COUNTER SELECT selector
4 AUDIO MONITOR selector
5 TIMER switch
6 REMOTE/LOCAL switch
7 MENU button
8 SET button
Location and Function of Parts
Chapter 1 Overview
14
GB
Chapter 1 Overview
7 MENU button
Press this button to display the menu on the monitor
screen. Press it again to return from the menu display
to the usual display.
Note
If you set the REMOTE/LOCAL switch to REMOTE
while the menu display is on the monitor, it returns to
the usual display.
On how to use the menu, see Chapter 5 “Menu Settings”.
8 SET button
Press this button to save selected menu items to the
unit’s memory.
9 Arrow (J j) buttons
Use these buttons to move around the menu items.
Rear Panel
INPUT OUTPUT
REF.VIDEO INPUT
MONITOR
CH-1
CH-2
CH-1/3
VIDEO
Y
AUDIO CH-1/3 AUDIO CH-2/4
R-Y B-Y
CH-2/4
CONTROL S
DV
IN/OUT
REMOTE
RS-422A
AUDIO
VIDEO
S VIDEO
AC IN
1 INPUT connectors
2 MONITOR connectors
3 OUTPUT connectors
4 REF. VIDEO INPUT connector
5 CONTROL S jack
6 REMOTE connector
7 DV jack
8 AC IN connector
1 INPUT connectors
Input video and audio signals. To connect a VCR
equipped with the S-video output jack, use the
S VIDEO jack on this VCR.
2 MONITOR connectors
Output video and audio signals for monitoring.
3 OUTPUT connectors
Output video and audio signals. To connect a VCR
equipped with the S-video input jack, use the S
VIDEO jack on this VCR. To connect a VCR
equipped with the component input connectors, use the
Y, R–Y, B–Y connectors on this VCR.
Chapter 1 Overview
Chapter 1 Overview 15
GB
Note on EE mode
When the S-video, video, or DV signal is input, this
VCR cannot output component signals. You can only
output the component signal during normal playback.
4 REF. VIDEO INPUT connector (BNC-type)
Input a reference video (black burst) signal.
5 CONTROL S jack
When controlling this VCR from an optional remote
control unit such as the DSRM-10/20 (not supplied),
connect the unit to this jack.
Note
SIRCS-system has the same function as
CONTROL S-system.
6 REMOTE connector (D-sub 9-pin)
Connect an editing controller with the RS-422A
interface for remote-control of this VCR.
7 DV jack
The DV jack is i.LINK compatible. Use when the
equipment connected to the VCR has a DV jack.
If you connect the VCR and the other equipment using
DV jacks, you can minimize deterioration of picture
quality during dubbing, or capturing still pictures by
digital processing. For details, refer to the instruction
manual of the equipment you use.
Note
is a trademark of Sony Corporation and indicates
that this product is in agreement with IEEE1394-1995
specifications and their revisions.
8 AC IN connector
Connect to an AC power outlet using the supplied
power cord.
Playback
Chapter 2 Playback and Recording
16
GB
Chapter 2 Playback and Recording
This section describes the necessary connections, settings and operations
to perform playback on this unit. The same settings and operations apply
whether you are using the unit as part of an editing system, for dubbing, or
as a stand-alone videocassette player.
Connections for Playback
To digital video equipment with the DV jack
The video and audio signals are sent with hardly any degradation, enabling
high-quality recording. The signal flow is automatically detected so you
need not make separate connections for input and output.
Notes
The external lock function of this unit only supports the standard sync
signals. With the DV connection, select the DV input with the INPUT
SELECT button on this VCR to prevent malfunction resulting from
noise, etc.
Set DV EE OUT in the menu to OFF (see page 52).
With the DV connection, the sound is recorded in the same audio
recording mode as that of the source tape.
With the DV connection, tape information (recording date, camcorder
data, etc.) recorded on the source tape is transmitted from this VCR
(player).
Playback
Recorder
This VCR (Player)
Monitor
to the DV
jack
DV
IN/OUT
L: Signal flow
i.LINK cable (DV connecting cable)
(not supplied)
Chapter 2 Playback and Recording
Chapter 2 Playback and Recording 17
GB
To video equipment without the DV jack
Notes
When you connect output jacks of the recorder to input jacks of this
VCR, select the input correctly to prevent a humming noise.
Distorted signals (e.g., when played back at a speed other than normal)
will not be recorded properly.
The indications (Time code, alarm messages, and menu, etc.) displayed
on the monitor screen are output only via the MONITOR connector.
If the DV input is selected, you cannot perform the playback
synchronized with the video reference (black burst) signal.
Chapter 2 Playback and Recording
Monitor
This VCR (Player)
Recorder
75 coaxial cable (not supplied)
S-video cable (not supplied)
XLR cable (not supplied)
Video cable (3BNCy3BNC) (not supplied)
to the S-video
input jack
to the video
input jack
to the audio
input jacks
INPUT OUTPUT
REF.VIDEO INPUT
MONITOR
CH-1
CH-2
CH-1/3
VIDEO
Y
AUDIO CH-1/3 AUDIO CH-2/4
R-Y B-Y
CH-2/4
AUDIO
VIDEO
S VIDEO
INPUT OUTPUT
REF.VIDEO INPUT
MONITOR
CH-1
CH-2
CH-1/3
VIDEO
Y
AUDIO CH-1/3 AUDIO CH-2/4
R-Y B-Y
CH-2/4
AUDIO
VIDEO
S VIDEO
L: Signal flow
to the video
input jacks
Playback
Chapter 2 Playback and Recording
18
GB
Chapter 2 Playback and Recording
Settings for Playback
Preparation on the player (this VCR)
1 Power on the video monitor, then set the monitor’s input according to
the input signals from the recorder.
2 Set up the recorder.
For details, see Preparation on the recorder below.
3 Power on this unit by pressing the ON/STANDBY switch.
The ON/STANDBY lamp lights in green.
4 When you play back a tape recorded in 4-channel mode (Fs 32k), set
the AUDIO MONITOR selector to MIX (see page 13). Then select the
precise balance between the tracks with the AUDIO MIX BALANCE
in the menu (see page 53).
Notes
With the DV connection, the playback VCR’s AUDIO MONITOR
(sound selection) and AUDIO MIX BALANCE (audio balance
adjustment) do not function on the source audio output through the DV
jack.
You cannot change the input signal selection during playback or playback
pause mode.
Preparation on the recorder
Insert a tape for recording.
Select the video and audio input signals to be recorded.
Note
Editing is not possible with a tape that is copyright protected.
Chapter 2 Playback and Recording
Chapter 2 Playback and Recording 19
GB
Standard size
Playback Procedure
Notes
When controlling this unit from an editing controller connected to the
REMOTE connector, set the REMOTE/LOCAL switch to REMOTE.
When not, set it to LOCAL.
Do not insert the cassette forcibly. The VCR may be damaged.
1 After checking the tape for slack, hold the cassette so that the tape
window is facing upward, then insert it into this unit as illustrated
below.
For details on checking the tape for slack, see page 9.
The cassette is automatically drawn into the unit.
2 Press PLAY.
This starts the playback operation.
Tape window facing upward
Mini size
Insert the mini-size cassette into
the center of the cassette
compartment.
Playback
Chapter 2 Playback and Recording
20
GB
Chapter 2 Playback and Recording
Playback Functions
You can enjoy various playback functions using the optional remote
control unit.
For details, refer to the operating instructions supplied with the remote control
unit.
Playing at various speeds (JOG)
You can play at various speeds, or frame by frame.
Searching (SHUTTLE)
You can easily locate the desired scene, and you can quickly and
accurately determine edit points.
Searching using the index function (DSRM-20 only)
Three kinds of search are available on this VCR:
Searching for the beginnings of recordings: Index search
Searching for a point on the tape where the recorded date changes:
Date search
Searching for scenes recorded in the photo mode with a digital
camcorder: Photo search
Note
When S-video or video input is selected and no signal is input in search
mode, the search screen becomes noisy. In such cases, input the signal or
select DV input.
For a description of search operations via external equipment, see the
equipments operating instructions.
Displaying tape information (DSRM-20 only)
If you record on a tape using a Sony digital camcorder DSR-200/200P/
200A/200AP/PD100/PD100P, camcorder data (the shutter speed, program
AE mode, white balance, iris and gain) can be recorded on the tape. You
can check these data during playback on this VCR.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132

Sony DSR-40 Manuel utilisateur

Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues