Breville the Hemisphere Control Manuel utilisateur

Marque: Breville

Modèle: the Hemisphere Control

Catégorie: Mélangeurs

Taper: Manuel utilisateur

the Hemisphere

™

Control

Instruction Book - BBL605

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL

INSTRUCTIONS BEFORE

USE AND SAVE FOR

FUTURE REFERENCE

• Remove any packaging

material and promotional

stickers before using the

Breville Hemisphere™

Control Blender for the ﬁrst

time.

• To eliminate a choking

hazard for young children,

remove and safely discard

the protective cover ﬁtted

to the power plug of this

appliance.

• Do not place the Breville

Hemisphere™ Control

Blender near the edge of a

counter-top or table during

operation. Ensure that the

surface is level, clean and

free of water, ﬂour, etc.

Vibration during operation

may cause the appliance to

move.

• Do not place the Breville

Hemisphere™ Control

Blender on or near a hot

gas or electric burner, or

where it could touch a

heated oven.

• Always ensure the Breville

Hemisphere™ Control

Blender is properly

assembled before use.

Refer to assembly and

operation instructions.

• Use only the blender jug

and lid supplied with the

Breville Hemisphere™

Control Blender.

• Always ensure the blender

lid is ﬁrmly positioned

on the blender jug before

operating.

• None of the recipes in

this instruction book are

considered a heavy load.

• Do not leave the Breville

Hemisphere™ Control

Blender unattended when

in use.

• Always ensure the Breville

Hemisphere™ Control

Blender is turned off by

pressing the ON | OFF

button on the control

panel. Then unplug

the cord. Make sure the

motor and blades have

completely stopped before

attempting to move the

appliance, or when the

Breville Hemisphere™

Control Blender is

not in use and before

disassembling, cleaning

and storing.

• If food becomes lodged

around the blending

blade, turn the Breville

Hemisphere™ Control

Blender off by pressing

the ON | OFF button on

the control panel. Then

unplug the cord. Make sure

the motor and blades have

completely stopped before

removing the jug from the

motor base. Use a spatula

to dislodge or stir the food

before continuing. Do not

use ﬁngers as the blades

are sharp.

• Keep hands, ﬁngers, hair,

and clothing as well as

spatulas and other utensils

away from the blender jug

during operation.

• Never place your ﬁngers,

hands or utensils inside

the blender jug without

unplugging the appliance

from the power outlet.

• Be careful when handling

the blending blade

assembly as the blades are

very sharp. Be careful when

emptying the blender

jug and during cleaning.

Mishandling of the blades

may cause injury.

• Do not remove the blender

jug from the motor base

while in operation.

• Do not use the Breville

Hemisphere™ Control

Blender for anything other

than food and/or beverage

preparation.

• The use of attachments,

including canning jars,

not recommended by the

manufacturer and may

cause risk of injury to

persons or damage to the

blender.

• Do not operate the Breville

Hemisphere™ Control

Blender without food or

liquid in the blender jug.

• CAUTION: Do not

process hot or boiling

liquids. Allow to cool

before placing into the

blender jug.

• Do not subject the blender

jug to extremes of hot or

cold, for example, placing a

cold jug in hot water or

vice versa.

• Keep the appliance clean.

Refer to care and cleaning

instructions in this manual.

WARNING

Please do not attempt

to use the blender

while the “OVERLOAD

PROTECTION” is ﬂashing.

• Once the icon stops

ﬂashing the blender has

now cooled down and

you will be able to use the

blender as per instructions.

At this point the blender

will be in standby mode

and you will only need to

press the function button

to start blending again.

However, if you have

turned the blender off you

will need to turn it back on

and only after the icon has

stopped ﬂashing return to

blending as usual.

• Flashing light indicates

ready to operate. Avoid

any contact with blades or

moveable parts.

WARNING

Do not operate the blender

continuously with heavy

load for more than

10 seconds.

IMPORTANT

SAFEGUARDS

FOR ALL

ELECTRICAL

APPLIANCES

• Fully unwind the cord

before use.

• To protect against electric

shock, do not immerse the

cord, plug or motor base in

water or any other liquid.

• Do not allow the cord to

hang over the edge of a

table or counter-top, touch

hot surfaces or become

knotted.

• Children should be

supervised to ensure that

they do not play with the

appliance.

• It is recommended to

regularly inspect the

appliance. Do not use

the appliance if the

power supply cord, plug

or appliance becomes

damaged in any way.

Return appliance to

nearest authorized Breville

Consumer Support for

repair or replacement.

• Any maintenance other

than cleaning should be

performed at an authorised

Breville Consumer

Support.

• This appliance is for

household use only. Do not

use in moving vehicles or

boats. Do not use outdoors.

Do not use this appliance

for anything other than its

intended use. Misuse may

cause injury.

• This appliance is equipped

with a power cord having

a grounding wire with

a grounding plug. The

appliance must be

grounded using a 3-hole

properly grounded outlet.

In the event of an electrical

short circuit, grounding

reduces the risk of

electrical shock.

• If the power outlet is

a standard 2-prong

wall outlet, it is your

personal responsibility

and obligation to have it

replaced with a properly

grounded 3-prong wall

outlet.

• Do not, under any

circumstances, cut or

remove the third (ground)

prong from the power cord

or use an adapter.

SHORT CORD

INSTRUCTIONS

Your Breville appliance

is ﬁtted with a short

power supply cord to

reduce personal injury or

property damage resulting

from pulling, tripping or

becoming entangled with a

longer cord.

If an extension cord is used,

(1) the marked electrical

rating of the cord set or

extension cord should

be at least as great as the

electrical rating of the

appliance, (2) the cord

should be arranged so

that it will not drape over

the countertop or table-

top where it can be pulled

on by children or tripped

over unintentionally and

(3) the extension cord

must include a 3-prong

grounding plug.

BREVILLE ASSIST

PLUG

Your Breville appliance

comes with a unique

Assist

Plug, conveniently

designed with a ﬁnger hole

to ease removal from the

power outlet. For safety

reasons it is recommended

you plug your Breville

appliance directly into its

own electrical outlet on a

dedicated circuit separate

from other appliances. If the

electric circuit is overloaded

with other appliances,

your appliance may not

function properly. Use in

conjunction with a power

strip or extension cord is

not recommended.

MADE WITH EASTMAN

TRITAN™ COPOLYESTER

Key beneﬁts of Eastman

Tritan™ copolyester

Your Breville Hemisphere™

Control Blender is made

with Eastman Tritan™

copolyester, which is a

tough, BPA-free polymer

used to make houseware

products that can stand

up to extreme use and

repeated dishwasher

cleaning. Products made

from Eastman Tritan™

copolyester are impact

resistant and shatter

resistant and stay clear and

durable even after hundreds

of cycles using common

dishwasher detergents.

Key attributes:

• Dishwasher durable

• Tough

• BPA free

• Temperature resistant

• Odor-, taste-, and

stain-resistant

• Sparkling clarity and gloss

CALIFORNIA

PROPOSITION 65:

(Applicable to California

residents only).

This product contains

chemicals known to the

State of California to cause

cancer, birth defects or other

reproductive harm.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

Components

A. Inner measuring lid

For adding ingredients while blending.

B. Large 48oz (1.5L) Eastman Tritan™

copolyester Jug

Unique dual ribs continually pass

ingredients onto the blades for well

blended results.

C. Die-cast metal base

For long lasting, professional performance.

D. Illuminated buttons

For clarity and ease of reading.

E. Electronic 5 speed control plus PULSE

Electronic controls ensure that the RPM

speed is maintained for consistent result

every time.

F. Breville Assist™ Lid

Unique ring pull design ensures the lid

is easy to remove yet sealed tight during

operation.

G. Stainless Steel ice-crushing blades

Extra wide stainless steel blades are

contoured to the base of the jug so there are

no food traps.

H. Hemisphere™ Blade and Bowl system

Revolutionary blade technology for

100% perfect blending and food

processing results.

I. Dishwasher Safe

The blender jug is ergonomically designed

for ease of cleaning and is dishwasher safe.

J. Pre-programmed ‘Ice Crush’ and

‘Smoothie’ settings

Automatically alter speeds to optimize

blending results, then turn off automatically.

K. LCD Display

Counts up on speed settings and down

for pre-programmed settings for complete

control when blending.

L. Surgical Grade Stainless Steel Blades

To ensure the blades stay sharp longer they

are made from surgical grade stainless steel.

The central blades are serrated for extra

cutting performance.

Functions

MANUAL SPEED SELECTION

ON | OFF

The ON | OFF button powers the unit into

READY mode.

CANCEL button

Cancels any function.

Electronic speed control

There are 5 electronic speed buttons from MIX

through to LIQUIFY.

MIX combines more delicate foods with a

folding motion, and is good for combining wet

and dry ingredients.

LIQUIFY is the fastest setting, and is ideal for

breaking down ingredients to make cocktails

and other ﬁnely blended mixtures.

PULSE

The momentary pulse button is ideal for

processing foods that need sudden bursts of

power. It also encourages ingredients to move

around the jug.

Count-up timer

The blender timer counts up in seconds as it

blends on one of the 5 electronic speeds from

MIX to LIQUIFY. When using the timer this

way, the blender will stop after 60 seconds, or

you can cancel blending manually.

PRESET PROGRAMS

Smoothie (60 seconds)

This program has been optimised to combine

and aerate frozen and liquid ingredients

together. The SMOOTHIE function has a

unique processing technique that blends

the denser ingredients at lower speed, then

increases in speed as ingredients thicken.

This will happen several times while blending

smoothies. The programming also circulates

the ingredients for maximum aeration and

creamy texture.

Pressing the button will activate the program –

press again to deactivate.

Ice crush (60 seconds)

Optimised to crush ice, and also ideal for

processing other foods that need sudden bursts

of power. This program has an intelligent

sensor to stop the motor when the ice is done.

Count-down timer

The blender timer counts down in seconds as

it blends in the SMOOTHIE or ICE CRUSH

programs.

AUTO CLEAN

Use to remove most of the ingredients off the

blender walls and blades. Add 2 cups warm

soapy water, and press the clean button.

For harder to clean, sticky or thick ingredients,

add ½ teaspoon of dish liquid detergent for

extra cleaning power. For best results, clean the

blender jug this way immediately after use.

NOTE

If the blender is running and a different button

is pressed, the speed will automatically switch

to that program without stopping.

BEFORE FIRST USE

Before using your Breville Hemisphere™

Control Blender for the ﬁrst time, remove any

packaging material and promotional labels.

Wash the lid, inner lid, blender jug (refer to

"Care & Cleaning) in warm, soapy water

with a soft cloth. Rinse and dry thoroughly.

Do not place parts in the dishwasher (with the

exception of the blender jug).

The blender jug may be washed in the

dishwasher. Ensure the lid has been removed

from the blender jug before placing into the

dishwasher. The motor base can be wiped with

a damp cloth. Dry thoroughly.

NOTE

The blending blades are extremely sharp.

Avoid any contact with ﬁngers and hands.

ASSEMBLING AND ATTACHING

THE BLENDER

Step 1

Place the motor base on a ﬂat, dry surface such

as a counter-top. Ensure that the motor base

is turned off at the ON | OFF button and the

power cord is unplugged.

Step 2

With the blender jug in the upright position

place it on the motor base. The handle of the

blender can be positioned to the left or right

hand side of the appliance.

Step 3

Add food or liquid into the blender jug

ensuring not to exceed the ‘MAX’ mark.

Place the blender lid ﬁrmly into position on

the top of the blender jug. Insert the clear inner

measuring lid into the blender lid and turn

clockwise to lock into position.

NOTE

The Breville Hemisphere™ Control Blender

features a Breville Assist™ Lid. This allows the

lid to ﬁt tightly onto the blender jug, avoiding

displacement during operation. The ring pull

design allows the user to easily remove the lid

with a simple leverage action.

Step 4

Plug power cord into a 110/120V power outlet

and turn on.

Step 5

Press the ON | OFF button on the far left of

the control panel to turn the blender on.

The ON | OFF button will illuminate and ﬂash.

The LCD timer screen will illuminate with

‘00’ displayed.

NOTE

• Flashing light indicates ready to operate.

Avoid any contact with moveable parts while

in operation.

• Do not ﬁll the blender jug above the ‘MAX’

line. When the blender jug is ﬁlled at or near

the ‘MAX’ line place one hand on the blender

lid to avoid displacement of the lid during

operation.

Step 6

Select the required speed (1 to 5) by pressing

the corresponding speed button. The blender

will start to operate and the selected speed

button will illuminate. The ON | OFF button

will illuminate and cease to ﬂash.

The CANCEL button will illuminate and ﬂash.

The LCD timer screen will start counting up

in one second increments until 60 seconds is

reached.

NOTE

Operate the blender only for the appropriate

amount of time required – do not over blend.

Step 7

When 60 seconds is reached, the blender

will automatically stop blending and the

selected speed button and CANCEL button

illumination will go out. The ON | OFF button

will illuminate and ﬂash. After a few seconds

the LCD timer screen will revert to ‘00’.

NOTE

• The Breville Hemisphere™ Control Blender

will automatically stop blending after

60 seconds. This is a safety feature and

restricts wear on the motor.

• To stop blending at any time, press the

CANCEL button or the selected speed

button. The ON | OFF button can also be

pressed, but this will also turn the appliance

off and all illuminations will go out.

• The speed can be changed at any time during

the blending process. Each time a new speed

is selected its button will illuminate and the

previous speed button illumination will go

out. The number of seconds on the LCD

timer screen will continue to count upwards

to 120 seconds unless interrupted.

Step 8

The Breville Hemisphere™ Control Blender

features two additional functions, ‘ICE CRUSH’

and ‘SMOOTHIE’. These two pre-programmed

cycles automatically adjust the blending time

and speeds to optimise blending results.

Select the required function by pressing the

corresponding function button. The blender

will start to operate and the selected function

button will illuminate. The ON | OFF button

will illuminate and stop ﬂashing. The CANCEL

button will illuminate and ﬂash. The LCD timer

screen will start counting down in one second

increments until ‘00’ is displayed.

FUNCTION PROGRAMMED TIME

Blend 60 seconds

Smoothie 60 seconds

Ice Crush 60 seconds

When ‘00’ seconds is reached, the blender will

automatically cease to operate and the function

button and CANCEL button illumination will

go out. The ON | OFF button will illuminate

and ﬂash.

To stop blending at any time, press the

CANCEL button or the selected function

button.

The ON | OFF button can also be pressed,

but this will also turn the appliance off and all

illuminations will go out.

The maximum amount of ice cubes the blender

can blend at any one time is 1 standard ice tray

or 250g.

WARNING

Never place anything other than food and

liquids in the blender while the motor is

running.

NOTE

The smoothie function has a unique

processing technique that blends the denser

ingredients at a lower speed, then increases as

ingredients thicken. This may happen several

times while blending smoothies.

Step 9

For ingredients that require short bursts of

power, select the PULSE function. The PULSE

button will illuminate and remain illuminated

while the button is depressed. When this

function is selected, the LCD timer screen

will illuminate and count upwards in one

second increments during pulsing. Press the

PULSE button in short bursts until blending is

complete.

NOTE

Use the PULSE button when the

food that is being processed is too thick or

coarse to circulate within the blender jug.

Step 10

At the end of use, always ensure the blender

is turned off by pressing the ON | OFF button

on the control panel. Then unplug the cord.

Ensure the motor and blades have completely

stopped before attempting to move the

appliance, or when the Breville Hemisphere™

Control Blender is not in use and before

disassembling, cleaning and storing.

NOTE

• During the blending process, ingredients

may stick to the sides of the blender jug.

To push the food back onto the blades, press

the ON | OFF button on the control panel to

turn blender off and remove the power cord.

Remove the lid and use a plastic spatula to

scrape down the sides of the jug. Replace the

lid before recommencing blending.

• If any moisture or liquid appears on top of

the motor base during blending, press the

ON | OFF button on the control panel, and

remove the power plug. Remove the blender

jug. Wipe the motor base immediately with a

dry cloth or paper towel to absorb the liquid.

Check the blender jug is correctly assembled.

• Never place anything other than food and

liquids in the blender while the motor is

running.

Hints & Tips

Do's

• If the volume (while blending) is below the

maximum line, the inner measuring cap can

be removed and oils/liquids can be added

while blender is in use.

• Run the blender only for the appropriate

amount of time required – do not over

blend ingredients.

• Use the PULSE button when food is too thick

or coarse to circulate within the blender jug.

• Do not exceed the maximum mark when

adding foods and liquids into the blender.

• Ingredients may stick to the sides of the

blender jug. To push food back onto the

blades, turn the blender off and unplug at the

wall. Use a plastic spatula to scrape down the

sides of the jug, and continue blending.

• If any moisture or liquid appears on top of

the motor base during blending, turn the

blender off and unplug at the wall. Remove

the blender jug, and wipe motor base

immediately with a dry cloth or

paper towel.

• To stop blending at any time or during

the SMOOTHIE program, press the

CANCEL button.

• When the blender has been running for

60 seconds, it will automatically turn off.

This is a safety feature to protect the motor.

• A speed or function can be selected at any

time, even while the blender is running.

Press the new speed or program, and the

blender will change operation immediately.

The motor will still automatically turn off at

120 seconds total time running time.

• The maximum amount of ice cubes that

the blender can process is 250g (approx.

1 standard ice tray).



Use the BLEND function for drink or

cocktail making, emulsions such as

mayonnaise, dressings, marinades and

foods that require mixing until just

combined, such as batters, also for pureeing

soups and aerating liquids.



Use a combination of the BLEND and

ICE CRUSH or PULSE functions to process

the foods being blended.



Use the SMOOTHIE function to blend

fruits, ice cream and yogurts into thick

smoothies, blended drinks, and milkshakes.



Use the ICE CRUSH or PULSE function

for foods that only require short bursts of

power.



Use the ICE CRUSH or PULSE function

with short bursts of power, when blending

drinks containing ice cubes or frozen fruit.



Ensure all foods are cut into cubes (approx.

1 square inch) where appropriate to achieve

an even result.



Do not put more than 2 cups of warm

ingredients into the blender jug before

blending commences. After the blending

process has begun and the blades are

turning you may slowly add another

1½ cups of ingredients through the

opening in the lid if desired.



Thick mixtures puree more efﬁciently if the

Breville Hemisphere™ Control Blender is

¼ to ½ full.



When using several ingredients, place

liquid ingredients in the blender jug

before solid ingredients, unless speciﬁed

in the recipe. When blending thick or dry

mixtures it may be necessary to stop the

Breville Hemisphere™ Control Blender and

scrape down the sides of the blender jug

with a plastic or rubber spatula, once or

twice during blending.

Don’ts



Do not overload the Breville Hemisphere™

Control Blender with more than the

speciﬁed quantity of ingredients as doing

so could cause the motor to stall. Turn

the blender off by pressing the ON | OFF

button on the control panel and unplug the

cord. Remove a portion of the mixture from

the blender jug before continuing.



Do not place hot or boiling ingredients into

the Breville Hemisphere™ Control Blender;

allow to cool before placing into the

blender jug.



Do not place the Breville Hemisphere™

Control Blender near the edge of a counter-

top or table during operation. Ensure that

the surface is level, clean and free of water,

ﬂour and other substances. Vibration

during operation may cause the appliance

to move.



Do not use metal utensils as they may

damage the blades or blender jug.



Do not operate a heavy mixture for more

than 10 seconds. For normal blending tasks,

for example, mayonnaise, dressings etc., do

not operate for longer than 60 seconds at

one time without turning off the Breville

Hemisphere™ Control Blender and stirring

the ingredients, and then continue blending.



Do not operate the Breville Hemisphere™

Control Blender without having the

blender lid in position. To add additional

ingredients while blending, remove the

inner lid and place ingredients through the

opening in the lid.



Do not place any objects, other than food

or liquid, into the Breville Hemisphere™

Control Blender while the motor is running.



Do not use the blender jug to store food.



The blender will not knead dough or

mash potatoes.



Do not remove the blender jug while

the Breville Hemisphere™ Control Blender

is operating. Always make sure the blender

is turned off by pressing the ON | OFF

button and unplug the power cord from the

power outlet.

Blending Chart

FOOD PREPARATION & USAGE

QUANTITY FUNCTIONS TIME

Raw vegetables Trim excess, cut into

1 inch pieces

Use: stufﬁng, ﬁlling, puree,

soup

2 cups/

200g

MIX/Speed 2 10–30 sec

Nuts Remove shells.

Use: cakes, toppings,

pastes

1½ cups/

200g

MIX/Speed 2 10–30 sec

Bread or

biscuit crumbs

Cut into 1 inch pieces,

break up cookies/crackers.

Use: cheesecake crust

1 cup/100g MIX/Speed 2 10–30 sec

Mayonnaise Mix the egg yolk and

vinegar. Add the oil.

Use: dressing

1½ cups/

125g

SNOW/Speed 1

BLEND/Speed 3

10 - 15 sec

60 sec

Whipped cream Add sugar or vanilla if

desired.

Use: topping

1¼ cups/

300ml

SNOW/Speed 1

PULSE

10 - 20 sec

1-2 times

Herbs and spices Chopped or halved.

Use: paste

1¼ cups/

1 cup

MIX/Speed 2 20–30 sec

Smoothie Milk, whole fresh fruits,

yogurt, ice cream.

Use: milkshakes, frappes

3½ cups/

Max 800ml

SMOOTHIE 60 sec

Fresh fruit Chopped or whole berries.

Use: dessert sauce

2 cups/

250g

BLEND/Speed 3 20–30 sec

Dried fruit Chopped dried fruit.

Use: fruit mince

2 cups/

300g

MIX/Speed 2 20 - 30 sec

Ice Crush.

Use: mixed drinks,

cocktails, slurpees

Max 1 tray/

250g

ICE CRUSH 60 sec

Carrot mixture Sliced carrots size not

more than 15mm.

Use: drinks

600g + water

900g

PULSE 30 sec

NOTE: This blending chart should be used as a guide only.

Troubleshooting

PROBLEM EASY SOLUTION

Motor doesn’t start or

blade doesn’t rotate

•

Check that the blender jug and lid are securely into position.

•

Check that the ON | OFF button and selected function or speed setting is

illuminated.

•

Check that the power plug is securely inserted into the power outlet.

Food is unevenly

chopped

•

Either too much food is being blended at one time or the pieces are too large.

Try cutting food into smaller pieces of even size and processing a smaller

amount per batch.

•

For best results, the food should be chopped into pieces no larger than 1 inch.

Food is chopped too

ﬁne or is watery

•

Try blending for shorter period of time. Use the PULSE function for

better control.

Food sticks to

blade and jug

•

The mixture may be too thick. Try adding more liquid and/or using a slower

speed for blending.

Blender overloaded

•

The Breville Hemisphere™ Control features a motor protection feature. If the

motor is being overloaded the motor will stop and the overload warning icon

on the LCD will start to ﬂash. Once the icon stops ﬂashing the blender has

now cooled down and you will be able to use the blender as per instructions.

At this point the blender will be in standby mode and you will only need to

press the function / button that you require to start blending again. However

if you have turned the blender off you will need to turn it back on and only if

the icon has stopped ﬂashing will the Blender commence blending as usual.

•

We recommend removing a portion of the mixture, cutting food into smaller

pieces or processing smaller amounts per batch.

Care & Cleaning

Jug And Lid

In order to keep your Jug clean and avoid food

drying on the blades and jug, follow the below

steps as soon as possible after use

• Rinse most of the ingredients off the jug

and lid.

• Add 2 cups of warm water and press the

AUTO CLEAN button. If thick or sticky

ingredients require extra cleaning power add

a few drops of dish liquid detergent.

• Rinse the jug and lid again and/or wash

separately in warm soapy water with a soft

cloth or bottle brush.

• It is most effective to clean the jug

immediately after use.

Motor base

To clean the motor base, wipe with a soft, damp

cloth then dry thoroughly. Wipe any excess

food particles from the power cord.

Cleaning agents

Do not use abrasive scouring pads or cleaners

on either the motor base or the jug, as they may

scratch the surface. Use only warm soapy water

with a soft cloth.

Dishwasher

The blender jug and lid can be washed in the

dishwasher on a standard wash cycle. Jug can

be placed on the bottom shelf, however the lid

and inner measuring cap should be washed on

the top shelf only.

Stubborn food stains and odours

Strong smelling foods such as garlic, ﬁsh and

some vegetables such as carrots may leave an

odour or stain on the blender jug and lid. To

remove, soak blender jug and lid for 5 minutes

in warm soapy water. Then wash with a mild

detergent and warm water, rinse well and dry

thoroughly. Store jug with the lid off.

Storage

Store your blender upright with the blender

jug assembled on the motor base, or beside it.

Do not place anything on top. To allow air to

circulate, keep the lid off.

the Hemisphere

™

Control

Manuel d'instructions - BBL605

BREVILLE VOUS

RECOMMANDE

LA SÉCURITÉ

AVANT TOUT

Chez Breville, la sécurité

occupe une place de choix.

Nous concevons et fabriquons

des produits de consommation

sans jamais perdre de vue la

sécurité de notre précieuse

clientèle. De plus, nous

vous demandons d'être très

vigilant lorsque vous utilisez

un appareil électrique et de

respecter les mesures de

sécurité décrites ci-dessous.

IMPORTANTES

MESURES DE

SÉCURITÉ

LISEZ TOUTES LES

INSTRUCTIONS AVANT

USAGE ET CONSERVEZ-

LES À TITRE DE

RÉFÉRENCE.

• Retirez tout matériel

d'emballage et étiquettes

promotionnelles avant

d'utiliser le mélangeur

Hemisphere

Control de

Breville pour la première

fois.

• Aﬁn d'éliminer les risques

de suffocation chez les

jeunes enfants, retirez

et jetez l'enveloppe

protectrice recouvrant la

ﬁche de l'appareil.

• Ne placez pas le

mélangeur Hemisphere

Control de Breville sur

le bord d'un comptoir

ou d'une table durant le

fonctionnement. Assurez-

vous que la surface de

travail est de niveau,

propre et exempte d'eau,

de farine ou toutes autres

substances. La vibration de

l'appareil qui fonctionne

peut le déplacer.

• Ne placez pas le

mélangeur Hemisphere

Control de Breville sur

ou près d'un élément

chauffant électrique ou

à gaz, ou là où il pourrait

toucher un four chaud.

• Assurez-vous de toujours

assembler correctement

votre mélangeur

Hemisphere

Control de

Breville avant l'utilisation.

Consultez les consignes

d'assemblage et de

fonctionnement contenues

dans ce manuel.

• Utilisez uniquement le

récipient et le couvercle

du mélangeur founis par

Breville.

• Assurez-vous toujours que

le couvercle est fermement

positionné sur le récipient

avant l'utilisation.

• Assurez-vous toujours

que le mélangeur

Hemisphere

Control

de Breville est éteint

en enfonçant la touche

MARCHE | ARRÊT

(ON | OFF) du panneau

de commande, puis

débranchez l'appareil.

Assurez-vous que le

moteur et les lames sont

complètement immobilisés

avant de tenter de déplacer

le Hemisphere

Control

de Breville, ou lorsqu'il

n'est pas en opération et

avant de le démonter, le

nettoyer et le ranger.

• Aucune des recettes

contenues dans ce manuel

n'est considérée comme

'lourde charge'.

• Ne laissez pas le

mélangeur Hemisphere

Control de Breville sans

surveillance lorsqu'il est en

marche.

• Si la nourriture se

loge autour des lames,

éteignez le mélangeur

Hemisphere

Control

La page charge ...

Breville the Hemisphere Control Manuel utilisateur

Marque: Breville

Modèle: the Hemisphere Control

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Breville the Hemisphere Control User manual

Breville the Hemisphere Control Manuel utilisateur

Breville the Hemisphere Control Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents