Korg K49 Manuel utilisateur

Owner’s Manual

Manuel d’utilisation

Bedienungsanleitung

Table of Contents

Precautions............................................................................ 3

Introduction ........................................................................... 4

Main Features...........................................................................................4

Controllers and their Functions ................................................................4

Setup ...................................................................................... 7

Installing the MIDI driver and softwares ...................................................7

Making connections and turning on the power.........................................8

About the K-Series and the driver ports .................................................10

About K-Series’ MIDI OUT connector.....................................................10

Restoring the factory preset programs ...................................................11

Operation ............................................................................. 12

Keyboard ................................................................................................12

ClickPoint................................................................................................12

KNOB1 and KNOB2 ...............................................................................12

SW1 and SW2........................................................................................13

OCTAVE SHIFT UP / OCTAVE SHIFT DOWN .......................................13

PITCH wheel ..........................................................................................13

MOD wheel.............................................................................................14

SLIDER ..................................................................................................14

PEDAL....................................................................................................14

Using the K61P’s Internal Sounds..................................... 15

Selecting a sound...................................................................................15

Effects.....................................................................................................15

Setting mode ..........................................................................................16

Program change enable/disable.............................................................20

Troubleshooting .................................................................. 22

Specifications...................................................................... 23

3

Owner’s Manual

Precautions

Location

Using the unit in the following locations can result

in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

• Close to magnetic fields

Power supply

Please connect the designated AC adapter to an

AC outlet of the correct voltage. Do not connect it

to an AC outlet of voltage other than that for which

your unit is intended.

Interference with other electrical devices

Radios and televisions placed nearby may experi-

ence reception interference. Operate this unit at a

suitable distance from radios and televisions.

Handling

To avoid breakage, do not apply excessive force

to the switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean,

dry cloth. Do not use liquid cleaners such as ben-

zene or thinner, or cleaning compounds or flam-

mable polishes.

Keep this manual

After reading this manual, please keep it for later

reference.

Keeping foreign matter out of your

equipment

Never set any container with liquid in it near this

equipment. If liquid gets into the equipment, it could

cause a breakdown, fire, or electrical shock.

Be careful not to let metal objects get into the

equipment. If something does slip into the equip-

ment, unplug the AC adapter from the wall outlet.

Then contact your nearest Korg dealer or the store

where the equipment was purchased.

THE FCC REGULATION WARNING (for

U.S.A.)

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential instal-

lation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communica-

tions. However, there is no guarantee that inter-

ference will not occur in a particular installation. If

this equipment does cause harmful interference

to radio or television reception, which can be de-

termined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equip-

ment and receiver.

• Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/

TV technician for help.

Unauthorized changes or modification to this sys-

tem can void the user’s authority to operate this

equipment.

CE mark for European Harmonized

Standards

CE mark which is attached to our company’s prod-

ucts of AC mains operated apparatus until De-

cember 31, 1996 means it conforms to EMC Di-

rective (89/336/EEC) and CE mark Directive (93/

68/EEC).

And, CE mark which is attached after January 1,

1997 means it conforms to EMC Directive (89/336/

EEC), CE mark Directive (93/68/EEC) and Low

Voltage Directive (73/23/EEC).

Also, CE mark which is attached to our company’s

products of Battery operated apparatus means it

conforms to EMC Directive (89/336/EEC) and CE

mark Directive (93/68/EEC).

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured according

to strict specifications and voltage requirements

that are applicable in the country in which it is in-

tended that this product should be used. If you

have purchased this product via the internet,

through mail order, and/or via a telephone sale,

you must verify that this product is intended to be

used in the country in which you reside.

WARNING: Use of this product in any country

other than that for which it is intended could be

dangerous and could invalidate the manufacturer’s

or distributor’s warranty.

Please also retain your receipt as proof of pur-

chase otherwise your product may be disqualified

from the manufacturer’s or distributor’s warranty.

Company names, product names, and names of

formats etc. are the trademarks or registered trade-

marks of their respective owners.

* Company names, product names, and names

of formats etc. are the trademarks or regis-

tered trademarks of their respective owners.

4

Introduction

Thank you for purchasing this K-Series USB/MIDI Studio Controller. For trouble-free

enjoyment of this controller, please read this manual carefully and use the product

only as directed. Keep this manual in a safe place where you can easily refer to it in the

future. This manual applies to the K25, K49, and K61. There is a special section that

covers the additional features of the K61P.

Main Features

❏ Equipped with a variety of expressive and powerful controllers.

❏ ClickPoint provides two simultaneous controllers (X and Y), and also serves as a

mouse for your software applications.

❏ Korg’s M1 Le software synthesizer is included with your K-Series controller, so you

can enjoy playing and creating high quality sounds immediately.

❏ The K61P contains an internal sound engine (borrowed form Korg’s digital piano

series) capable of producing 24 high fidelity sounds - including piano, electric pi-

ano, organs and more.

Controllers and their Functions

1

2

3

4

5

6

7

8

K61P

Controller

5

Owner’s Manual

1. Keyboard

The keyboard features full-size, velocity-sensing keys.

2. ClickPoint

Two modes allow the ClickPoint controller to behave as an X - Y realtime controller,

or as a clickable cursor/mouse when working with Softsynths or DAW software

running on a computer.

3. KNOB1 / KNOB2

With MIDI control assignment, KNOB1/KNOB2 can be used to operate connected

external MIDI equipment and software synthesizer such as DAW running on PC.

4. SW1 / SW2

These two assignable switches can be assigned independently to any MIDI control

change number, allowing you to control other MIDI devices or music software pro-

grams. They can also be used as Up 1 and Down 1 buttons when selecting pro-

grams (Program Change).

5. OCTAVE SHIFT UP / OCTAVE SHIFT DOWN

The octave buttons shift the pitch up and down in units of one octave.

6. PITCH wheel

The Pitch Bend Wheel provides a smooth, continuous up or down change in pitch,

that can be controlled in realtime.

7. MOD wheel

The Modulation Wheel can be assigned to any MIDI control change number, al-

lowing you to control other MIDI devices or music software programs.

8. SLIDER

The Slider can be assigned to any MIDI control change number, allowing you to

control other MIDI devices or music software programs, and is especially handy for

functions such as volume and expression.

Sound Generator(K61P)

1

2 34

5

1. VOLUME knob

This knob controls the volume of the internal sound engine. This sound is sent

from the OUTPUT jacks (L/MONO,R) and the HEADPHONE jack.

2. BANK button

The 24 internal sounds are arranged in three banks, each containing eight sounds.

This button selects the current bank.

6

3. PROGRAM buttons

Use one of these buttons to select a sound from within the current bank.

4. REVERB button

This button is used to select the depth of the reverb effect, and to turn it on and off.

5. CHORUS button

This button is used to select the depth of the chorus effect, and to turn it on and off.

Rear panel

1

2

3 4 5 6 7

Illustration shows the rear panel of K61P.

1. OUTPUT jacks (K61P only)

These are the output jacks of internal sound engine. These can be connected to an

amplifier, audio monitoring system, or to an audio recording device.

2. HEADPHONES jack (K61P only)

This jack is provided so that you can listen to the internal sound engine through a

set of stereo headphone (standard plug).

3. PEDAL jack

An optional momentary pedal (such as the Korg PS-2 pedal switch) can be con-

nected to the pedal jack. The K-Series will automatically detect the polarity of the

pedal when the power is turned on.

4. MIDI OUT connector

The MIDI out jack provides direct control of other MIDI equipped sound modules or

audio devices. (P.10 “About the K-Series’ MIDI OUT connector”)

5. USB connector

The USB connector allows your K-Series controller to communicate directly with

your computer.

6. Power switch

This switch turns the K-Series on by selecting either DC(Adapter) or USB

power.When not in use, this switch places the K-Series in the standby mode. (p.8

“Making connections and turning on the power”)

7. Power supply connector

Connect the optional AC adapter here. For ultimate convenience, the K-Series

controllers can be powered directly from the USB bus - in most cases. In situations

using an unpowered USB hub, or when controlling a MIDI module, you may wish to

use an AC adapter.

7

Owner’s Manual

Setup

Installing the MIDI driver and softwares

Contents of the CD-ROM

The included CD-ROM contains the follwing.

❏ K-Series editor

❏ KORG M1 Le software synthesizer

❏ KORG USB-MIDI driver for Windows XP

❏ Installation guide

❏ K-Series editor owner’s manual

❏ M1 Le software synthesizer owner’s manual

❏ Software license

Operating requirements

■ Mac OS X users

Computer

Apple Macintosh computer with a USB port that satisfies the operating require-

ments of Mac OS X

Supported operating systems

Mac OS X ver.10.3 or later

■ Windows XP users

Computer

A computer with a USB port, that satisfies the operating requirements of Microsoft

Windows XP (USB chipset made by Intel Corporation is recommended)

Supported operating systems

Microsoft Windows XP Home Edition/Professional Service pack 1 or later

Install

On the CD-ROM included with your K-Series controller, please refer to the installation

instructions regarding the installation of the KORG USB-MIDI Driver for Windows XP,

the K-Series Editor, and the M1 Le software synthesizer.

Please read before use

❏ Copyright to all software pertaining to this product is the property of Korg Corpora-

tion.

❏

A license agreement for the software pertaining to this product is included separately.

You must read this license agreement before you install the software. Your installation

of the software will be taken to indicate your acceptance of the agreement.

❏ Apple, Macintosh and Mac OS are registered trademarks of Apple Computer, Inc.

❏ Windows XP is a registered trademark of Microsoft Corporation in the U.S. and

other countries.

❏ All other product and company names are trademarks or registered trademarks of

their respective holders.

8

Making connections and turning on the power

Be sure all your equipment is turned off BEFORE you begin hooking everything up. You

must excercise caution, otherwise you may damage your speaker system or cause

other malfunctions.

Connections using USB

1 Use a USB cable to connect the K-Series to the USB connector of your computer.

2 If you want to use a pedal, connect it to the PEDAL jack.

The K-Series will detect the polarity of the pedal when the power is turned on.

Therefore, if a pedal is connected, do not hold it down while you turn the power on.

3 To turn on the power, set the K-Series’ power switch to the USB position.

Pedal switch

PEDAL jack

Power switch position

USB cable

Computer

USB connector

4 When you are ready to turn off the power, set the power switch to STANDBY.

If you’re using a USB connection, you generally don’t need to use an AC adapter.

However if your computer is low-powered, or if you are using a hub that is only bus-

powered (rather than self-powered), sufficient power may not be supplied to the K-

Series. In this case, use the optional AC adapter and set the power switch to the

DC position.

When USB is connected, MIDI OUT jack does not send out MIDI messages from

the K-Series’ keyboard and controller.

Connections using MIDI

1 Connect the plug of the optional AC adapter to the K-Series’ power connector, and

plug the adapter into an AC outlet.

2 Use a MIDI cable to connect the K-Series to your external MIDI sound module.

3 If you want to use an optional pedal, connect it to the pedal jack.

The K-Series will detect the polarity of the pedal when the power is turned on.

Therefore, if a pedal is connected, do not hold it down while you turn the power on.

9

Owner’s Manual

4 Set the power switch to the DC position. The power LED will light. When the power

is turned on, the most recently saved settings will be recalled automatically.

5 Turn on any external MIDI sound modules connected to your K-Series controller.

MIDI IN

MIDI OUT

Pedal switch

MIDI cable

External MIDI sound module

PEDAL jack

Power switch position

Plug the AC

adaptor into

an AC outlet

Power supply connector

6 When you are ready to turn off the power, turn off any external MIDI sound mod-

ules first, and then set the K-Series power switch to STANDBY.

Using the internal sound engine [K61P only]

1 Connect the plug of the optional AC adapter to the K-Series power connector, and

plug the adapter into an AC outlet.

2 Using standard instrument cables with 1/4” plugs, connect the output jacks on the

K61P to the inputs of your audio monitor system or audio recorder. When connect-

ing only one output, use the L/MONO jack only.

Use the volume knob to adjust the level of the OUTPUT jacks.

3 Set the power switch to the DC position. The power LED will light.

4 Turn on your connected audio monitoring system.

Headphone

Amplified speakers

HEADPHONES jack

OUTPUT jack

INPUT

10

About the K-Series and the driver ports

From the computer’s point-of-view, the K-Series provides 1 USB-MIDI port and 2 USB-

MIDI out ports.

Keyboard/Slider/

Pitch,Mod wheel/

SW1/SW2/Pedal/

ClickPoint/

Dump data

The driver of the application

on a computer

K-series

MIDI OUT device

MIDI IN device

MIDI OUT

KBD/KNOB

SOUND/CTRL *1

MIDI OUT juck

Dump data

Sound generator *2

*1 K25/49/61 is CTRL

*2 K61P only

MIDI IN device

KBD / KNOB

This is used to receive MIDI messages from the keyboard and the various controllers

on the K-Series. When operating a computer application from the K-Series, select this

port as the application’s MIDI input. KBD/KNOB is also used to receive scene data.

Select this port as the K-Series Editor’s MIDI input.

MIDI OUT device

MIDI OUT

MIDI OUT transmits software MIDI OUT messages to K-Series' MIDI OUT jack, i.e

transmits MIDI messages from a computer application to external MIDI equipment. When

the K-Series is used as a USB-MIDI controller, select this port for computer application’s

MIDI output.

SOUND / CTRL (CTRL if K25/K49/K61)

SOUND/CTRL is used to receive scene data from the computer. Select this port as the

K-Series Editor’s MIDI input. In addition, this port is used to play notes on internal

sound engine of the K61P.

About K-Series’ MIDI OUT connector

When USB is not connected

Sends MIDI messages from K-Series’ keyboard and controller.

When USB is connected

Sends MIDI messages from computer’s MIDI OUT port. It will not send MIDI messages

from K-Series’ keyboard and controller.

11

Owner’s Manual

Restoring the factory preset programs

To restore the K-Series to the original factory settings, hold down SW1 and SW2 while

turning on the power.

The controllers setting when factory is shipped

Controller Function

SW1 / SW2 Program change (-1/+1)

KNOB1 CC#074 (Cutoff)

KNOB2 CC#079 (EG Intensity)

SLIDER CC#007 (Volume)

PITCH wheel Fixed (Pitch Bend)

MOD wheel CC#001 (Modulation)

PEDAL CC#064 (Damper)

ClickPoint Mouse mode

* The parameters shown inside the brackets relate to the M1 Le.

12

Operation

The K-Series editor software (included on the CD-ROM) is used to assign the control-

ler settings and certain parameter values.

MIDI messages are sent using MIDI channel.

Keyboard

Note messages are sent from the keyboard.

Three velocity curves (and a constant 127 velocity) allow the keyboard response to be

tailored to the performer’s playing style.

The keyboard may be transposed by semitones into any musical key.

ClickPoint

MIDI control changes can be assigned individually to the “X” direction (left/right) and

the “Y” direction (up/down) to simultaneously control two parameters. In addition, the

ClickPoint can be used as a computer mouse.

The assignable values are “No Assign/Control Change/Mouse”.

No Assign

No MIDI information is sent from this controller.

Control Change [0...127]

Moving the ClickPoint controller will change the value of the parameters assigned to

the X and Y axis

The ClickPoint controller will return to the center position when it’s released. To lock the

X and Y parameters at their current values, press down (Z axis) on the center switch of

the ClickPoint. Press it again to unlock the X and Y values.

Mouse Mode

When set to “Mouse” mode, the ClickPoint can be operates as a mouse and will control

the cursor on computer screen. The ClickPoint switch functions as the mouse.

The Mouse Mode is only operative when the connected to a computer via USB.

KNOB1 and KNOB2

By assigning MIDI control changes, these knobs can be used to operate external MIDI

equipment and control musical software applications. Each knob can be assigned indi-

vidually.

The assignable values are “No Assign/Control Change”.

No Assign

No MIDI information is sent from this controller.

Control Change [0...127]

Turning the knob will change the value of the assigned parameter.

13

Owner’s Manual

SW1 and SW2

These two switches can be assigned individually to send a specific value to a specific

MIDI control change parameter. In fact, both an “on” and “off” value can be set. The

switch type can be set to Momentary or Toggle.

The assignable values on SW1 and SW2 are “No Assign/Program Change/Control

Change”.

No Assign

No MIDI information is sent from this controller.

Program Change

Every time [SW1] is pressed, the program change number is decreased by 1.

Every time [SW2] is pressed, the program change number is increased by 1.

In addition, a program change message of “0” is sent if [SW1] are [SW2] are pressed

simultaneously.

Control Change [0...127]

SW1 and SW2 can be assigned MIDI control change parameters; Toggle or Momen-

tary mode; plus an On Value and a Release Value.

In “Toggle” mode, each time a switch is pressed, a MIDI control message is sent; each

press will alternate between the On Value and the Release Value.

In “Momentary” mode, the On Value MIDI control message is sent when the switch is

pressed down, and a Off Value MIDI control message is sent when the switch is re-

leased.

OCTAVE SHIFT UP / OCTAVE SHIFT DOWN

These buttons can shift pitch of the keyboard in one octave units.

The octave shift range is different depending on the keyboard length.

K-Series’ type Octave ranges

K25 -4...+4

K49 -4...+4

K61/K61P -3...+3

Key lights(status) Octave setting

Dark ±0 octave

Green +1 / -1octave

Orange +2 / -2octave

Red +3 / -3octave

Red Flashing +4 / -4octave(K25/K49 only)

PITCH wheel

Use the Pitch Bend Wheel to send MIDI pitch bend messages.

14

MOD wheel

By assigning a MIDI control change number, the Modulation Wheel can be used to

operate external MIDI equipment and control musical software applications.

The assignable values are “No Assign/Control Change/After touch”.

No Assign

No MIDI information is sent from this controller.

Control Change [0...127]

Use the Mod Wheel to smoothly change the value of the assigned MIDI control change

parameter.

After Touch

Use the Mod Wheel to send channel AFTERTOUCH messages.

SLIDER

By assigning a MIDI control change number, the Modulation Wheel can be used to

operate external MIDI equipment and control musical software applications.

The assignable values are “No Assign/Control Change”.

No Assign

No MIDI information is sent from this controller.

Control Change [0...127]

Use the slider to smoothly change the value of the assigned MIDI control change pa-

rameter.

PEDAL

An optional pedal switch can be assigned to send a specific value to a specific MIDI

control change parameter. In fact, both an “on” and “off” value can be set. The switch

type can be set to Momentary or Toggle.

The assignable values are “No Assign/Control Change”.

No Assign

No MIDI information is sent from this controller.

Control Change [0...127]

The pedal is assigned to MIDI controls with Toggle/Momentary mode selection, On

Value and Off Value.

In “Toggle” mode every time press the pedal, MIDI control message with parameter On

Value and Off Value will be sent in turn.

In “Momentary” mode every time press the pedal, MIDI control message with param-

eter On Value will be sent when press down and MIDI control message with parameter

Off Value will be sent when releas up.

15

Owner’s Manual

Using the K61P’s Internal Sounds

Selecting a sound

The 24 Internal sounds of the K61P are organized into three banks each containing

eight sounds. To select a particular sound, you need to select a program button and a

bank. For example, to select the Clavi sound, press the sixth program button from the

left (the key will light). Then press the bank button to select BANK2.

1 Press the program key corresponding to the sound you want to select.

2 Press the bank button to select one of the three banks.

Every time the bank key is pressed, the selected bank will switch from BANK1,

BANK2 or BANK3. The selected bank will be shown by the bank lights.

For example, to select the Clavi sound, press the sixth program key from the left to

turn on the key light. Then press the bank key to select BANK2.

[PROGRAM] key

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Bank2

E. Piano 1

E. Piano 2

Soft E.P.

Vintage E.P.

E.P. Pad

Clavi

Vibraphone

Choir

Bank3

Jazz Organ 1

Jazz Organ 2

Jazz Organ 3

Church Organ 1

Church Organ 2

Church Organ 3

Strings

Slow Strings

Osc#

2

1

2

1

2

Osc#

1

2

1

Osc#

2

3

1

2

Bank1

Grand Piano 1

Grand Piano 2

Standard Piano

Bright Piano

Honky Tonk Piano

Mellow Piano

Harpsichord 1

Harpsichord 2

Sound List

* [PROGRAM] key is BANK1’s label.

* Indicates the number of oscillators used to produce the voice.

Effects

Reverb

Reverb adds a concert hall ambience by simulating the echoes and sound reflection of

such an environment.

1 Press the [REVERB] button to select one of the three reverb depths. The selected

setting will be shown by the color of the [REVERB] button.

[REVERB] button lights Reverb depth

Dark Off

Green Light

Orange Standerd

Red Deep

16

Chorus

Chorus adds a sense of depth and motion to the sound

1 Press the [CHORUS] button to select the depth of the chorus effect. The selected

setting will be shown by the color of the [CHORUS] button.

[CHORUS] key Chorus depth

Dark Off

Green Light

Orange Standerd

Red Deep

Setting mode

The Setting mode is used to access and change the settings of other features on the

K61P. To enter the Setting mode, hold down the Bank button. The BANK lights and the

8 program button lights will turn off. Now you can use the 8 program buttons to select

the function you want to change. The selected program button light will flash. Then

press the note on the keyboard to set the value.

When you are done, press the [BANK] button to exit the Setting mode.

The eight items available in the Setting mode are shown below:

[PROGRAM] keys

[PIANO 1]

[PIANO 2]

[PIANO 3]

[PIANO 4]

[PIANO 5]

[PIANO 6]

[HARPSI 1]

[HARPSI 2]

Contents

Velocity Curve Setting

Transposing the Keyboard

Adjusting the Pitch

Selecting a Temperament

Changing the Global MIDI Channel Setting

The Local Control On/Off Setting

Enabling or Disabling Program Changes

Enabling or Disabling Volume Message Filter

Function

Velocity curve

Transpose

Pitch

Temperament

Global MIDI channel

Local control

Program Change Setting

Volume message filter

*

[PROGRAM] key is BANK 1’s lablel.

Velocity curve

There are 3 velocity curves and a constant (127) velocity setting. You can select any

one of them to match your performance or playing style.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 1 [PIANO 1/E.P. 1/ORGAN 1] button (the button will flash).

3 To select the curve, press C4 for (soft), C#4 (standard), D4 (hard),or D#4 (const).

C8C7C6C5C4C3C2C1

17

Owner’s Manual

4 Press the [BANK] button to exit the Setting mode.

Gentle

Soft ( )

Strong

Loud ( )

Light

Heavy

Normal

Key Force

Output

Level

Note Touch, control change setting

C4 Light (less force is required to play loudly)

C#4 Standard(general piano intensity)

D4 Heavy (gently struck notes are played softer)

D#4 CONST(all notes play with a velocity of 127)

Velocity Curve setting is used by controller and

sound generator.

Transpose

By transposing the keyboard, you can play a song in a different musical key without

changing your fingering.

Transpose is set in semitone, ranges within ±1 octave(-12...12).

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 2 [PIANO 2/E.P. 2/ORGAN 2] button (the button will flash).

Press one of the notes between C3...C5 to select the transpose setting.

C8C7C6C5C4C3C2C1

-12

+120

3 Press note C4 to cancel the transpose function.

4 Press the [BANK] button to exit the Setting mode.

Transpose setting is used by controller and sound generator.

Pitch

The overall pitch, or tuning, of the K61P’s internal sound engine can be adjusted to

match other instruments or recordings.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 3 [PIANO 3/E.P. 3 ORGAN 3] button (the button will flash).

3 Press note C4 to increase the pitch; every time C4 is pressed, the pitch increases

about 0.5Hz

Press note B3 to decrease the pitch; every time B3 is pressed, the pitch decreases

about 0.5Hz

C8C7C6C5C4C3C2C1

Press note B3 and C4 together to restore standard pitch A4=440Hz.

18

4 Press the [BANK] button to exit the Setting mode.

The pitch setting reverts to standard A4=440Hz if the power is cut off

Temperament

Temperaments are different tuning systems, mainly used in the baroque and classical

periods. In addition to the standard equal tuning, the K61P provides historical Kirnberger

and Werckmeister temperaments.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 4 [PIANO 4/E.P. 4/ORGAN 4] button (the button will flash).

3 To select a temperament, press C4 for Kirnberger, C#4 for Weckmeister, or D4 for

Equal tuning.

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

Note

C4

C#4

D4

Temperament

Werckmeister: Uses the Werckmeister scale proposed in

the late Baroque period by organist and musicologist Andreas

Werckmeister, with the intention of enabling relatively

unrestricted play in multiple keys.

Kirnberger: Uses the Kirnberger scale proposed in the

Johann Philip Kirnberger in the early 18th century. This

temperament is mainly used for tuning harpsichords.

Equal temperament: The temperament used on almost all

modern keyboard instruments. This temperament uses equal

semitone increments, so that scales sound identical in all keys.

The termperament setting is set to equal temperament if power cut off.

A Note About “Stretch Tuning”

Stretch tuning is used to obtain a more natural sound. Low diapason notes use a lower

pitch setting, and high diapason notes use a higher pitch setting. This is the most often

used method when tuning an acoustic piano. There are 6 instrument sounds in the

K61P that use stretch tuning:

[PROGRAM] keys BANK 1

[PIANO1] Grand Piano 1

[PIANO2] Grand Piano 2

[PIANO3] Standard Piano

[PIANO4] Bright Piano

[PIANO5] Honky Tonk Piano

[PIANO6] Mellow Piano

19

Owner’s Manual

MIDI channel setting

You can set the K61P to the same MIDI channel as the connected MIDI equipment.

MIDI channel is 1-16.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 5 [PIANO 5/E.P. 5/ORGAN 5] button (the button will flash).

3 Press one of the notes between C4~D#5.

The MIDI channel assignments are as the followings.

C4 = 1ch, C#4=2ch, D4=3ch…D#5= 16ch

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

MIDI channel setting is used by controller and sound generator.

The Local control on/off setting

The Local setting separates the K61P’s keyboard from the internal sound engine. When

local is on, the keyboard will play the internal sound engine, as well as any other

connected devices. When using the K61P with a sequencer, you would normally set

the local control to off, to prevent messages being sent to the computer from triggering

notes a second time. This setting will depend on the “echo back” setting of the se-

quencer.

Generally, set local on, and the K61P will play sounds from the internal engine when

notes are played on the keyboard.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 6 [PIANO 6/CLAVE/ORGAN 6] button (the button will flash).

3 Press note C4(On) or C#4(Off) to select the setting.

C8C7C6C5C4C3C2C1

4 Press the [BANK] button to exit the Setting mode.

20

The local control setting

Keyboard/Each controllers

Computer

K61P

KBD/KNOB

SOUND/CTRL

Tone generator

Local control on

Computer

KBD/KNOB

SOUND/CTRL

Local control off

Keyboard/Each controllers

K61P

Tone generator

The local on/off setting is set to local on if power cut off.

Program change enable/disable

Every time you select one of the K61P’s internal sounds, a MIDI program change

message is also sent to any connected MIDI equipment. This feature allows you to

prevent program change messages from being sent to your other MIDI devices.

1 Hold down [BANK] button until the K-Series enters the Setting mode.

2 Press the Program 7 [HARPSI 1/VIBE/STRINGS 1] button (the button will flash).

C8C7C6C5C4C3C2C1

3 Press note C4(enable) or C#4(disable) to select the setting.

4 Press the [BANK] button to exit the Setting mode.

La page charge ...

Korg K49 Manuel utilisateur

Korg K49 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents