NEC Computer Monitor 42XM5 Manuel utilisateur

PlasmaSync Plasma Monitor

NEC Corporation of America

User’s Manual

Manuel d’utilisation

Manual del Usuario

Manual de Usuário

User’s Manual

PlasmaSync

™

42XM5

PX-42XM5A

PlasmaSync

™

50XM6

PX-50XM6A

PlasmaSync

™

60XM5

PX-60XM5A

ENGLISH

User’s Manual

(Enhanced split screen Model)

En-2

Precautions

Please read this manual carefully before using your plasma monitor and

keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER. NO USER-SERVICEABLE

PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any

kind of contact with any part inside of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included.

Therefore, it should be read carefully in order to avoid

any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S

POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR

OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY

INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE

ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide

long, trouble-free service. No maintenance other than cleaning

is required. Please see the section “Plasma monitor cleaning

procedure”.

The plasma display panel consists of fine picture

elements (cells) with more than 99.99 percent active cells. There

may be some cells that do not produce light or remain lit.

For operating safety and to avoid damage to the unit, read

carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat build-

up. Do not cover rear vents or install the unit in a closed cabinet or

shelves.

If you install the unit in an enclosure, make sure there is adequate

space at the top of the unit to allow hot air to rise and escape. If the

monitor becomes too hot, the overheat protector will be activated and

the monitor will be turned off. If this happens, turn off the power to the

monitor and unplug the power cord. If the room where the monitor is

installed is particularly hot, move the monitor to a cooler location, and

wait for 60 minutes to cool the monitor. If the problem persists, contact

your dealer for service.

2. Do not use this unit’s polarized plug with extension cords or outlets

unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the

power cord.

5. Unplug the power cord during electrical storms or if the unit will

not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage

components inside. If the unit is damaged in this way the warranty will

be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. The manufacturer is not

liable for any bodily harm or damage caused if unqualified persons

attempt service or open the back cover. Refer all service to authorized

Service Centers.

8. This equipment shall be connected to a MAIN outlet with a protective

earth-ground connection.

9. The outlet shall be installed near the equipment and shall be easily

accessible.

To avoid damage and prolong operating life:

1. Use only with 100 V to 240 V 50 Hz/60 Hz AC power supply. Continued

operation at line voltages greater than 100 V to 240 V AC will shorten

the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Set the unit away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In

case of accident, unplug the power cord and have it serviced by an

authorized Service Center.

5. Do not hit or scratch the panel surface as this causes flaws on the surface

of the screen.

6. For correct installation and mounting it is strongly recommended to

use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a CRT monitor,

for example) light output will gradually decrease over the life of a Plasma

Display Panel.

8. To avoid sulfurization it is strongly recommended not to place the unit

in a dressing room in a public bath or hot spring bath.

9. Do not use in a moving vehicle, as the unit could drop or topple over

and cause injuries.

10. Do not place the unit on its side, upside-down or with the screen facing

up or down, to avoid combustion or electric shock.

11. To prevent a fire hazard, do not place near an open flame (such as a

lighted candle).

Plasma monitor cleaning procedure:

1. Use a soft dry cloth to clean the front panel and bezel area. Never use

solvents such as alcohol or thinner to clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush

nozzle attachment.

3. To ensure proper ventilation, cleaning of the ventilation areas must be

carried out monthly. More frequent cleaning may be necessary

depending on the environment in which the plasma monitor is installed.

Recommendations to avoid or minimize image retention:

Like all phosphor-based display devices and all other gas plasma displays,

plasma monitors can be susceptible to image retention under certain

circumstances. Certain operating conditions, such as the continuous

display of a static image over a prolonged period of time, can result in

image retention if proper precautions are not taken. To protect your

investment in this plasma monitor, please adhere to the following

guidelines and recommendations for minimizing the occurrence of image

retention:

* Always enable and use your computer’s screen saver function

during use with a computer input source.

* Display a moving image whenever possible.

* Change the position of the menu display from time to time.

* Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the

following measures to reduce the likelihood of image retention:

* Lower the Brightness and Contrast levels as much as possible without

impairing image readability.

* Display an image with many colors and color gradations (i.e.

photographic or photo-realistic images).

* Create image content with minimal contrast between light and dark

areas, for example white characters on black backgrounds. Use

complementary or pastel color whenever possible.

* Avoid displaying images with few colors and distinct, sharply defined

borders between colors.

Plasma monitor driving sound

The panel of the Plasma monitor is composed of extremely fine pixels and

these pixels emit light according to received video signals. This principle

may cause you to hear a buzz or electrical hum coming from the Plasma

monitor. Also note that the rotation speed of the cooling fan motor increases

when the ambient temperature of the Plasma monitor becomes high. You

may hear the sound of the motor at that time.

Note:

The following items are not coverd by the warranty.

• Image retention

• Panel generated sound, examples: Fan motor noise, and electrical

circuit humming /glass panel buzzing.

Contact your dealer for other recommended procedures that will best

suit your particular application needs.

Important Information

En-3

Warning

Not for use in a computer room as defined in the

Standard for the Protection of Electronic Computer/

Data Processing Equipment ANSI/NFPA 75.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

This Class B digital apparatus complies with

Canadian ICES-003.

CAUTION

When disposing of used batteries, please comply

with governmental regulations or environmental

public instruction’s rules that apply in your country/

area.

Disposing of your used

product

EU-wide legislation as implemented in

each Member State requires that used electrical

and electronic products carrying the mark (left)

must be disposed of separately from normal

household waste. This includes plasma monitors

and their electrical accessories. When you dispose

of such products, please follow the guidance of

your local authority and/or ask the shop where you

purchased the product.

After collecting the used products, they are reused

and recycled in a proper way. This effort will help

us reduce the wastes as well as the negative

impact to the human health and the environment

at the minimum level.

The mark on the electrical and electronic products

only applies to the current European Union

Member States.

core

Remote cable (not supplied)

To plasma monitor

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding)

pin. This plug only fits a grounding-type power

outlet. If you are unable to insert the plug into an

outlet, contact a licensed electrician to replace the

outlet with a properly grounded one. Do not defeat

the safety purpose of the grounding plug.

Operating Environment

Operating environment temperature and humidity:

0 °C to +40 °C (+32 °F to +104 °F); less than 80

%RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area,

or in locations exposed to high humidity or direct

sunlight (or strong artificial light)

NOTE:

When you use the power cable (supplied), use the supplied

ferrite cores. Set the ferrite cores (supplied) on both ends

of the power cable (supplied), and then use the bands

(supplied) to fasten the ferrite cores (supplied) to the power

cable (supplied). If you do not this, this monitor will not

conform to mandatory FCC standards.

Po

w

e

r

cable

(

su

pp

lie

d

)

core

ba

n

d

ba

n

d

NOTE:

When you use a remote cable (not supplied), use the

supplied ferrite core. Wind the remote cable (not supplied)

around the ferrite core (supplied) once, and then fasten

the catch. If you do not this, this monitor will not conform

to mandatory FCC standards.

NOTE:

When you use an RGB cable (not supplied), use an RGB

cable including the ferrite core (not supplied) on both ends

of the cable. If you do not this, this monitor will not

conform to mandatory FCC standards.

CAUTION

When changing batteries, use only conventional

non-rechageable alkaline or manganese batteries

(2).

Risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries according

to the institutions.

En-4

Contents

Important Information .................................. En-2

Contents ...................................................... En-4

Contents of the Package ........................................En-4

Options .............................................................. En-4

Installation .................................................. En-5

Ventilation Requirements for enclosure mounting ...... En-5

Creating a video wall ........................................... En-6

Cable Management..............................................En-6

Caution when placing the plasma monitor in portrait mode .....

En-7

Using the remote control ....................................... En-7

Battery Installation and Replacement .......................... En-7

Using the wired remote control mode ......................... En-7

Operating Range ......................................................... En-7

Part Names and Function .............................. En-8

Front View .......................................................... En-8

Rear View/ Terminal Board ...................................En-9

Remote Control .................................................. En-12

Basic Operations ......................................... En-13

POWER ............................................................ En-13

To turn the unit ON and OFF: ................................... En-13

VOLUME .......................................................... En-13

To adjust the sound volume: ...................................... En-13

MUTE ............................................................... En-13

To mute the audio: .................................................... En-13

DISPLAY ............................................................ En-13

To check the settings: ................................................ En-13

DIGITAL ZOOM ................................................. En-13

AUTO ADJUST .................................................. En-13

To adjust the size or quality of the picture automatically: ...

En-13

OFF TIMER ........................................................ En-13

To set the off timer: ................................................... En-13

To check the remaining time: .................................... En-13

To cancel the off timer: ............................................. En-13

WIDE Operations ......................................... En-14

Wide Screen Operation (manual) ........................ En-14

When viewing videos or digital video discs .............. En-14

Wide Screen Operation with Computer Signals ..... En-15

When “PICTURE SIZE” is set to “OFF” .................. En-15

SPLIT SCREEN Operations ............................. En-16

Showing a couple of pictures on the screen at the same time ..

En-16

Operations in the Side-by-side mode ......................... En-16

Operations in the Picture-in-picture mode ................. En-17

Selecting the input signals to be displayed ................ En-17

Zooming in on a specific input .................................. En-17

Adjusting the OSM controls ...................................... En-17

OSM (On Screen Menu) Controls ................... En-18

Menu Operations ............................................... En-18

Menu Tree ......................................................... En-19

Picture Settings Menu.......................................... En-21

Adjusting the picture ................................................. En-21

Setting the picture mode according to the brightness

of the room ............................................................. En-21

Reducing noise in the picture .................................... En-21

Setting the color temperature .................................... En-21

Adjusting the color to the desired level ..................... En-22

Changing the Gamma Curve ..................................... En-22

Making the Low Tone adjustments ........................... En-22

Adjusting the colors .................................................. En-22

Audio Settings Menu .......................................... En-23

Adjusting the treble, bass and left/right balance and

audio input select .................................................... En-23

Setting the allocation of the audio connectors ........... En-23

Image Adjust Settings Menu ................................ En-23

Adjusting the Position, Size, Fine Picture,

Picture Adj and Underscan ..................................... En-23

Option1 Settings Menu ....................................... En-24

Setting the on-screen menu ....................................... En-24

Setting the BNC input connector type ....................... En-24

Checking the signal being transmitted to RGB1 terminal ...

En-24

Setting a computer image to the correct RGB select screen ....

En-24

Setting high definition images to the suitable screen size ...

En-25

Setting the Input Skip ................................................ En-25

Resetting to the default values ................................... En-25

Option2 Settings Menu ....................................... En-26

Setting the power management for computer images ....

En-26

POWER/STANDBY indicator .................................. En-26

Setting the picture to suit the movie .......................... En-26

Reducing image retention ......................................... En-26

Setting the gray level for the sides of the screen ........ En-28

Setting the screen size for S1/S2 video input ............. En-29

Setting the picture size for RGB input signals ........... En-29

Setting the signal and black level for DVI signal ...... En-29

Setting the Protocol set ............................................. En-29

Setting CloseCaption ................................................ En-30

Setting the contrast of CloseCaption ......................... En-30

Option3 Settings Menu ....................................... En-30

Using the timer ......................................................... En-30

Setting the power on mode ........................................ En-32

Enabling/disabling the front panel controls ............... En-32

Enabling/disabling remote control wireless

transmission ........................................................... En-33

Loop Out setting ....................................................... En-33

REMOTE ID setting ................................................. En-33

ID number setting ..................................................... En-33

Video Wall setting ..................................................... En-34

Option4 Settings Menu ....................................... En-36

Removing the sub screen area when there is no input

signal detected for the sub picture .......................... En-36

Displaying the entire image during DIGITAL ZOOM

operations ............................................................... En-36

Displaying still images in the sub screen ................... En-36

Switching the input source quickly ........................... En-37

Displaying the information as a text .......................... En-37

Advanced OSM Settings Menu ............................ En-38

Setting the menu mode .............................................. En-38

Language Settings Menu ..................................... En-38

Setting the language for the menus ........................... En-38

Color System Settings Menu ................................ En-38

Setting the video signal format .................................. En-38

Source Information Menu .................................... En-38

Checking the frequencies, polarities of input signals, and

resolution ............................................................... En-38

External Control ......................................... En-39

Application ....................................................... En-39

Connections ...................................................... En-39

Type of connector: D-Sub 9-pin male ....................... En-39

Communication Parameters ................................. En-39

External Control Codes (Reference) ...................... En-39

Pin Assignments ......................................... En-39

mini D-Sub 15-pin connector (Analog) ................. En-39

DVI-D 24-pin connector (Digital) .......................... En-39

1/8 Stereo Mini Jack (not supplied) for

REMOTE IN/OUT ........................................... En-40

Connection with STB .................................... En-40

Troubleshooting.......................................... En-41

Table of Signals Supported .......................... En-42

Specifications ............................................. En-46

Limited Warranty

Plasma Monitors ................. En-49

Contents of the Package

䡺 Plasma monitor (⳯1)

䡺 Power cord (⳯1, 3 m/9.8 feet)

䡺 Remote control (⳯1)

䡺 AAA Batteries (⳯2, Manganese battery for remote

control)

䡺 Manuals (Start up Guide and CD-ROM)

䡺 Ferrite cores for power cord (⳯2), bands for power

cord (⳯2)

䡺 Ferrite core for remote cable (⳯2)

䡺 Cable clampers (⳯3), beads bands (⳯3)

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop Stand

• Attachable speakers

En-5

50 mm (2")

Wall

50 mm (2")

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall

mount unit, Stand, etc.)

• For correct installation and mounting it is strongly recommended to use a trained, authorized

dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury

to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only a mounting kit or stand recommended by the manufacturer and listed as an accessory.

Drawing B

Drawing A

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between surrounding

objects as shown on the diagram when installing.

Installation

CAUTION

• Install the device following the installation manual of the optional accessory.

• Install the device in a stable and level environment that is strong enough to support the weight.

• Use the specified clasps for installing.

• After installation, take appropriate measures to prevent the plasma from tipping over or falling.

• Make sure to move or install the device with more than one person(s).

En-6

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an

extraordinary load.

2. LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3. LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1 m to 2 m (3.3 feet to 6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially

available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024⳯768, 60 Hz

signal.

• A distribution amplifier is particularly recommended when creating a 3⳯3 (or greater) video wall.

• When looping from plasma to plasma, a 1 m to 2 m (3.3 feet to 6.6 feet) 15 pin male D-Sub - 5BNC conversion

cable is required.

Creating a video wall

With built-in matrix display capability, you can create a (2⳯2, 3⳯3, 4⳯4, 5⳯5, 5⳯1, 1⳯5) video wall.

• Connect signal cables and remote cables as shown below.

Video signal RGB/DVD/HD signal

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/ HD

1

R

1

3

2

(

MONO

)

L

YCb/PbCr/Pr

RGB

2

/ DVD

2

/ HD

2

RGB

1

VDHD

DVI

(

Digital RGB

)

R

L

AUDIO

2

(

MONO

)

R

L

AUDIO

3

(

MONO

)

R/Cr/Pr G/Y B/Cb/Pb

RGB

3

IN OUT

REMOTE

EXTERNAL CONTROL

IN

OUT

Remote

control

Remote

control

BNC connector

RCA phono plug

OUT

VIDEO Signal

IN

VIDEO Signal

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/

HD

1

R

1

3

2

(

MONO

)

L

Y Cb/Pb Cr/Pr

RGB

2

/

DVD

2

/

HD

2

RGB

1

VDHD

DVI

(

Digital RGB

)

R

L

AUDIO

2

(

MONO

)

R

L

AUDIO

3

(

MONO

)

R/Cr/Pr G/Y B/Cb/ Pb

RGB

3

IN OUT

REMOTE

EXTERNAL CONTROL

BNC connector

RGB signal/

DVD/HD signal

IN

OUT

IN

OUT

Remote

control

RGB signal/

DVD/HD signal

Remote

control

Cable Management

Using the cable clampers and beads bands provided with the plasma display; Bundle the signal and audio cables at the

back of the unit to connect to the display.

42XM5 50XM6 60XM5

Back of the unit

mounting holes

Back of the unit

mounting holes

Back of the unit

mounting holes

To attach

Insert q into a mounting hole, then

snap w into the back of q to fix the

clamper.

Clampers are designed to be difficult

to undo once in place. Please attach

carefully. Cables can be routed to the

right or left.

To detach

Using pliers, twist the clamper 90° and

pull it outward. In some cases the

clamper may have deteriorated over

time and may get damaged when

removed.

Bunch separated cables together and

secure them with the provided beads

bands.

Do not allow excessive stress to be

placed on the ends of cables.

En-7

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

-

RIGHT/

+

/EXIT

VOLUME

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

-

RIGHT/

+

/EXIT

VOLUME

Top side

Bottom side

90°

: RGB

: AUTO

: 1080B

: OFF

1024ⴒ768

EXIT

SEL.

RETURN

MENU/ENTER

OK

OPTION1

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

Caution when placing the plasma monitor in portrait mode

• Use the optional mount. Contact your store to purchase before installing.

• Rotate 90° clockwise as seen from the front when installing.

• After installing, make sure the NEC logo is located at the

left hand side of the screen when facing the plasma from

the front.

• Be sure to set “OSM ANGLE” to “V” when using.

* Failure to heed the above cautions may lead to malfunction.

Using the remote control

Battery Installation and Replacement

Designated batteries:

Please use size AAA (R03) or AAA (LR03).

Insert the 2 “AAA” batteries, making sure to set them in

with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the and

indication inside the case.

3.Replace the cover.

* The 1/8 Stereo Mini cable must be purchased separately.

IN

OUT

4

REMOTE

EXTERNAL CONTROL

Remote Control

Cable*

To Remote Jack

Operating Range

* Use the remote control within a distance of about 7 m/ 23

ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately

30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct

sunlight or strong artificial light, or if there is an obstacle

between the sensor and the remote control.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote

jack and the “REMOTE IN” terminal on the monitor.

When the cable is connected, the mode automatically

switches to wired remote control. When the wired remote

control mode is used, the remote control can be operated

even if no batteries are loaded.

Approx.

7 m/23 ft

CAUTION

• Use only the specified batteries.

• Make sure to insert the batteries correctly according

to the indications of and .

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote

control gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use

different types together.

• Do not take apart the batteries, heat them, or throw

them into a fire.

• When using the remote control in the wireless

condition, be sure to unplug the remote cable from

the REMOTE IN terminal on the monitor.

En-8

q Power

Turns the monitor’s power on and off.

w Remote sensor window

Receives the signals from the remote control.

e POWER/STANDBY indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

r INPUT SELECT / EXIT

Switches the input.

Functions as the EXIT buttons in the On-Screen Menu

(OSM) mode.

Front View

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

-

RIGHT/

+

/EXIT

VOLUME

MENU/ ENTER

INPUT SELECT

DOWN UP LEFT/

-

RIGHT/

+

/ EXIT

VOLUME

4

5

6

7

1

3

2

t LEFT/– and RIGHT/+

Functions as the CURSOR (



/



) buttons and used

to adjust the picture parameters in the On-Screen Menu

(OSM) mode.

y VOLUME DOWN and UP

Adjusts the volume.

Functions as the CURSOR (▲/▼) buttons in the On-

Screen Menu (OSM) mode.

u MENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays

the main menu.

WARNING

The Power on/off switch does not completely

disconnect power from the display.

Part Names and Function

En-9

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

(positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the

EXT SPEAKER terminal on

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

J REMOTE IN

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

L Handles

Use when installing or carrying the plasma monitor.

Rear View/ Terminal Board

42XM5

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/ HD

1

R

1

3

2

(

MONO

)

L

Y Cb/ Pb Cr /Pr

RGB

2

/ DVD

2

/ HD

2

RGB

1

VDHD

DVI

(

Digital RGB

)

R

L

AUDIO

2

(

MONO

)

R

L

AUDIO

3

(

MONO

)

R/Cr/Pr G/Y B/C b/Pb

RGB

3

IN OUT

REMOTE

EXTERNAL CONTROL

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/ HD

1

YL/R L/RCb/Pb Cr/Pr

RGB

2

/ DVD

2

/ HD

2

RGB

1

VD L/RHD

DVI

AUDIO

2

AUDIO

3

R/Cr/Pr G/Y B/Cb/Pb

RGB

3

EXTERNAL CONTROL

IN OUT

REMOTE

BA

L

D

CE F GHIJK

En-10

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

(positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the

EXT SPEAKER terminal on

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

J REMOTE IN

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

L Handles

Use when installing or carrying the plasma monitor.

Rear View/ Terminal Board

50XM6

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/

HD

1

R

1

3

2

(

MONO

)

L

Y Cb/Pb Cr/Pr

RGB

2

/

DVD

2

/

HD

2

RGB

1

VDHD

DVI

(

Digital RGB

)

R

L

AUDIO

2

(

MONO

)

R

L

AUDIO

3

(

MONO

)

R/Cr/Pr G/Y B/C b/Pb

RGB

3

IN OUT

REMOTE

EXTERNAL CONTROL

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/

HD

1

YL/R L/RCb/Pb Cr/Pr

RGB

2

/

DVD

2

/

HD

2

RGB

1

VD L/RHD

DVI

AUDIO

2

AUDIO

3

R/Cr/Pr G/Y B/Cb/Pb

RGB

3 EXTERNAL CONTROL

IN OUT

REMOTE

BA

L

D

CE F GHIJK

En-11

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/ HD

1

R

1

3

2

(

MONO

)

L

Y Cb/Pb Cr/Pr

RGB

2

/ DVD

2

/ HD

2

RGB

1

VDHD

DVI

(

Digital RGB

)

R

L

AUDIO

2

(

MONO

)

R

L

AUDIO

3

(

MONO

)

R/Cr/Pr G/Y B/C b/Pb

RGB

3

IN OUT

REMOTE

EXTERNAL CONTROL

VIDEO

(IN/OUT)

AUDIO

1

DVD

1

/ HD

1

YL/R L/RCb/Pb Cr/Pr

RGB

2

/ DVD

2

/ HD

2

RGB

1

VD L/RHD

DVI

AUDIO

2

AUDIO

3

R/Cr/Pr G/Y B/Cb/Pb

RGB

3

EXTERNAL CONTROL

IN OUT

REMOTE

BA

L

D

CE F GHIJK

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

(positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the

EXT SPEAKER terminal on

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

J REMOTE IN

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

L Handles

Use when installing or carrying the plasma monitor.

Rear View/ Terminal Board

60XM5

En-12

q POWER ON/STANDBY

Switches the power on/standby.

(This does not operate when the POWER/STANDBY

indicator of the plasma is off.)

w RGB/PC

Press this button to select RGB/PC as the source.

RGB/PC can also be selected using the INPUT

SELECT button on the monitor.

e DVD / HD

Press this button to select DVD/HD as the source.

DVD/HD can also be selected using the INPUT

SELECT button on the monitor.

r VIDEO

Press this button to select VIDEO as the source.

VIDEO can also be selected using the INPUT SELECT

button on the monitor.

t MENU/ENTER

Press this button to access the OSM controls.

Press this button during the display of the main menu

to go to the sub menu.

y CURSOR (▲ / ▼ /



/



)

Use these buttons to select items or settings and to

adjust settings or switch the display patterns.

u EXIT

Press this button to exit the OSM controls in the main

menu. Press this button during the display of the sub

menu to return to the previous menu.

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

!0 VOLUME (+ /–)

Adjusts the audio volume.

!1 MUTE

Mutes the audio.

!2 WIDE

Press this button to select and switch the screen sizes.

WIDE button is not active for all signals.

!3 DISPLAY

Displays the source settings on the screen.

!4 OFF TIMER

Activates the off timer for the unit.

!5 SIDE BY SIDE

Press this button to show a couple of pictures in the

side-by-side mode.

!6 PICTURE IN PICTURE

Press this button to show a couple of pictures in the

picture-in-picture mode.

!7 SINGLE

Cancels the split screen mode.

!8 SELECT/FREEZE

Press this button to select the active picture in a split

screen mode.

When the PIC FREEZE function is operating, this button

can be used to display still images on the sub screen.

!9 AUTO ADJUST

Press this button to adjust Fine Picture, Picture ADJ,

Position, and Contrast automatically. Press this button

in video mode and the Auto Adjust switches to ZOOM

mode automatically when a letter box image is

displayed.

@0 ID SELECT

Set the ID number in the remote control. The remote

control can then be used only for a display with the

same ID number. When several displays are used

together they can be controlled individually.

@1 CLEAR/SEAMLESS SW

Clears the number set by the ID SELECT button.

When the SEAMLESS SW function is operating, this

button can be used to switch the input source quickly.

@2 Remote control signal transmitter

Transmits the remote control signals.

@3 Remote Jack

Insert the plug of the remote cable (The 1/8 Stereo

Mini cable) here when using the supplied remote

control in the wired condition.

Remote Control

→ VIDEO1 → VIDEO2 → VIDEO3

En-13

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set.

3. Press the POWER ON button (on the remote control) to

turn on the unit.

The monitor’s POWER/STANDBY indicator will light

up (green) when the unit is on.

4.

Press the POWER STANDBY button (on the remote control)

or the Power button (on the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set (only when turning off the

unit with the remote control).

VOLUME

To adjust the sound volume:

1. Press and hold the VOLUME button (on the remote

control or the unit) to increase to the desired level.

2. Press and hold the VOLUME

button (on the remote

control or the unit) to decrease to the desired level.

MUTE

To mute the audio:

Press the MUTE button on the remote control to mute the

audio; press again to restore.

DISPLAY

To check the settings:

1. Press the DISPLAY button to display the display mode.

2. If the button is not pressed for approximately three seconds,

the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges

the picture.

1. (Be sure ZOOM NAV is off.)

Press the POINTER button to display the pointer. (

)

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying glass.

(

)

A press of the ZOOM- button will reduce the picture

and return it to its original size.

To change the picture position:

Select the position with the ▲▼





buttons.

2. Press the POINTER button to delete the pointer.

AUTO ADJUST

To adjust the size or quality of the picture

automatically:

Press the AUTO ADJUST button.

Information

 AUTO ADJUST ON setting

When RGB (still picture) input is selected:

Fine Picture, Picture ADJ, Position, and Contrast will

be adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr

(component) input is selected:

The screen size switches to ZOOM mode automatically

when a letter box image is displayed.

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30, 60,

90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30

minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

OFF TIMER 30

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

2. The remaining time is displayed, then turns off after a few

seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

OFF TIMER 28

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

OFF TIMER 0

Note:

After the power is turned off with the off timer ...

A slight current is still supplied to the monitor. When you

are leaving the room or do not plan to use the system for a

long period of time, turn off the power to the monitor.

En-14

Wide Screen Operation

(manual)

With this function, you can select one of seven screen sizes.

When viewing videos or digital video discs

1. Press the WIDE button on the remote control.

2. Within 3 seconds ...

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN

When a 720P or 1080I signal is input:

FULL ↔ 2.35:1

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3)

The normal size screen is displayed.

* The picture has the same size as video pictures with a 4 : 3

aspect ratio.

FULL size screen

The image is expanded in the horizontal direction.

* Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and

displayed on the entire screen with correct linearity.

(Normal images are expanded in the horizontal direction.)

STADIUM size screen

The picture is expanded in the horizontal and vertical

directions at different ratios.

* Use this for watching normal video programs (4:3) with a

wide screen.

ZOOM size screen

The picture is expanded in the horizontal and vertical

direction, maintaining the original proportions.

* Use this for theater size (wide) movies, etc.

2.35:1 size screen

The squeezed film image is expanded to fulfill the entire

screen at a ratio of 2.35:1. Black bands do not appear at

the top and bottom but information is lost on the left and

right margins.

• This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB

(525P or 625P signal from a scan converter).

* If black bands appear on the top and bottom in the full size

screen, select the 2.35:1 size screen to fill the screen and

avoid image retention.

14:9 size screen

The image is displayed at a 14:9 aspect ratio.

* This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P) or RGB (525P or 625P

signal from a scan converter).

UNDERSCAN size screen

Set “UNDERSCAN” to “ON” in the “IMAGE ADJUST”.

Typical televisions crop the image (i.e., overscan). In order

to restore the entire image, select UNDERSCAN.

* Picture noise or black border may appear near the edge of

screen depending on the connected component.

* The continuous display in this screen size over a prolonged

period of time may result in image retention.

* When Macrovision signal is input, the brightness may

change.

Note:

Do not allow 4:3 content to be displayed for extended

periods of time without using gray bars. This can cause

image retention.

WIDE Operations

Information is lost on both sides.

Original image



Overscan

Underscan

En-15

FULL size screen

The image is expanded in the horizontal and vertical

direction.

ZOOM size screen

When wide signals are input.

TRUE

The image is true resolution.

FULL

Information

 Supported resolution

See page En-42 for details on the display output of the

various VESA signal standards supported by the

monitor.

 “PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size

of RGB-input pictures will be TRUE in place of

NORMAL.

 When 852 (848) dot  480 line wide VGA*

signals with a vertical frequency of 60 Hz and

horizontal frequency of 31.7 (31.0) kHz are

input

Select an appropriate setting for RGB SELECT mode

referring to the“Table of Signals Supported” on page

En-42.

* “VGA”, “SVGA” and “SXGA” are registered

trademarks of IBM, Inc. of the United States.

Note:

Do not allow 4:3 content to be displayed for extended

periods of time without using gray bars. This can cause

image retention.

Wide Screen Operation with

Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image

to fill the entire screen.

1. Press the WIDE button on the remote control.

2. Within 3 seconds ...

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → FULL → ZOOM

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal direction.

ZOOM size screen

When wide signals are input.

FULL size screen

When “PICTURE SIZE” is set to “OFF”

* This cannot be set in some models. “TRUE” size will not

be displayed in such cases.

The screen size switches as follows:

→ TRUE → FULL → ZOOM

TRUE size screen (VGA, SVGA 4:3)

The image is true resolution.

En-16

Showing a couple of pictures on the

screen at the same time

* There may be some RGB-input signals that may not be

displayed as not all signals are supported.

1. Press the button to select a screen mode from among single

mode, side-by-side, and picture-in-picture.

Note:

Picture A and B on the above screen are not always of the

same height.

Operations in the Side-by-side mode

To change the picture size, press the cursor





or



button.

To swap the picture on the right and the left, press the

cursor



button.

VIDEO1 RGB1

AB

VIDEO1RGB1

BA

To make the desired picture active, press the SELECT/

FREEZE button.

VIDEO1 RGB1

AB

VIDEO1 RGB1

AB

SELECT/FREEZE

button

Information

Split screen operations may not function depending on

the combination of input signals. In the table below,

“” means Yes, “” means No.

 Split screen operations may not function

depending on the frequency of the RGB

signals.



button

SPLIT SCREEN Operations

VIDEO1

Sub

screen

Main screen

RGB1

A

VIDEO1

VIDEO1 RGB1

AB

SIDE BY SIDE

button

PICTURE IN PICTURE

button

SINGLE

button

PICTURE IN

PICTURE

button

SINGLE

button

SIDE BY SIDE

button

VIDEO1

VIDEO2

VIDEO3

DVD/HD1

DVD/HD2

RGB1

RGB2

RGB3

VIDEO1





VIDEO2





VIDEO3





DVD/HD1







DVD/HD2











RGB1







RGB2











Pictures

displayed on

the left/sub

screen

(Select2)

Pictures displayed on the right/main screen (Select1)

RGB3





VIDEO1 RGB2

A

B

VIDEO1 RGB2

AB

VIDEO1 RGB2

B

A

VIDEO1 RGB2

A

B

VIDEO1 RGB2

AB

VIDEO1 RGB2

B

A

Side-by-Side2-R

Side-by-Side1 Side-by-Side2-L

Side-by-Side4-R

Side-by-Side3 Side-by-Side4-L



button



button



button



button



button



button



button



button



button



button



button



button



button



button



button

En-17

Operations in the Picture-in-picture mode

To move the position of the sub screen, press the cursor



or



button.

To change the size of the sub screen, press the



button.

VIDEO1 RGB1

A

B

VIDEO1 RGB1

A

B

VIDEO1 RGB1

A

B

VIDEO1 RGB1

A

B

 button

To make the desired picture active, press the SELECT/

FREEZE button.

Selecting the input signals to be displayed

1. Press the SELECT/FREEZE button to make the desired

picture active.

2. Press the RGB/PC, VIDEO, or DVD/HD button.

Each press of the button changes the selection of the input

signal.

The INPUT SELECT button on the monitor can also be

used to change the selection.

Zooming in on a specific input

1. Press the SELECT/FREEZE button to make the desired

picture active.

2. Use the POINTER button and the ZOOM/ button to

enlage the picture.

For details, see “DIGITAL ZOOM” on page En-13.

Adjusting the OSM controls

1. Press the SELECT/FREEZE button to make the desired

picture active.

2. Press the MENU/ENTER button to display the MAIN

MENU.

3. Adjust the setting to your preference.

For details, see “OSM (On Screen Menu) Controls” on

page En-18.

Note:

During enhanced split screen, some functions of OSM

controls are not available.

SELECT/

FREEZE

button

VIDEO1 RGB2

A

B

VIDEO1 RGB2

A

B

RGB2

A

B

VIDEO1

A

B

VIDEO1

RGB2

Bottom Left Bottom Right



button



button



button



button

Top Right



button



button



button



button

Top Left

VIDEO1 RGB1

A

B

VIDEO1 RGB1

A

B

En-18

Menu Operations

The OSM window is displayed with respect to the

screen as shown on the diagram.

* Depending on the screen’s mode, the OSM may be

displayed differently.

In the explanation, the OSM section is shown close up.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

ADVANCED OSM

EXIT

MENU/ENTER

OK

EXIT

The following describes how to use the menus and the

selected items.

1. Press the MENU/ENTER button on the remote control to

display the MAIN MENU.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

ADVANCED OSM

EXIT

MENU/ENTER

OK

EXIT

SEL.

MAIN MENU 2 / 2

COLOR SYSTEM

SOURCE INFORMATION

EXIT

MENU/ENTER

OK

EXIT

2. Press the cursor buttons ▲ ▼ on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/ENTER button on the remote control to

select a sub menu or item.

SEL. ADJ. RETURN

PICTURE 1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NR

: OFF

: 52

: 32

: 16

: 32

GR

EXIT

4. Adjust the level or change the setting of the selected item

by using the cursor buttons





on the remote control.

5. The adjustments or settings are then stored in memory.

The change is stored until another change is made.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the EXIT button on the remote control to return to the

main menu.

* When adjusting using the bar at the bottom of the screen,

press the



or



button within 5 seconds. If not, the

current setting is stored and the previous screen appears.

Note:

The main menu disappears by pressing the EXIT

button.

Information

 Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main

menu (1/2), full menu items will be shown.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

OPTION2

OPTION3

OPTION4

ADVANCED OSM

EXIT

MENU/ENTER

OK

EXIT

* The actual screen may be different from the ones in

this manual.

OSM (On Screen Menu) Controls

En-19

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

PICTURE CONTRAST ←→ 0←52→72 YES YES En-21

BRIGHTNESS ←→ 0←32→64 YES YES En-21

SHARPNESS ←→ 0←16→32 YES YES En-21

COLOR ←→ 0←32→64 YES YES En-21

TINT R←→G 0←32→64 YES YES En-21

PICTURE MODE BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT YES YES En-21

NR OFF/NR-1/NR-2/NR-3 YES YES En-21

COLOR TEMP. LOW/MID LOW/MID/HIGH YES YES En-21

WHITE BALANCE GAIN RED ←→  0←40→70 YES NO En-22

GAIN GREEN ←→ 0←40→70 YES NO En-22

GAIN BLUE ←→ 0←40→70 YES NO En-22

BIAS RED ←→ 0←40→70 YES NO En-22

BIAS GREEN ←→ 0←40→70 YES NO En-22

BIAS BLUE ←→ 0←40→70 YES NO En-22

RESET OFF←→ON YES NO En-22

GAMMA 1←→2←

…

→4 YES NO En-22

LOW TONE *

4

MODE1←→MODE2 YES NO En-22

COLOR TUNE RED Y←→M0←32→64 YES NO En-22

GREEN C←→Y0←32→64 YES NO En-22

BLUE M←→C0←32→64 YES NO En-22

YELLOW G←→R0←32→64 YES NO En-22

MAGENTA R←→B0←32→64 YES NO En-22

CYAN B←→G0←32→64 YES NO En-22

RESET OFF←→ON YES NO En-22

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

AUDIO BASS ←→ 0←13→26 YES YES En-23

TREBLE ←→ 0←13→26 YES YES En-23

BALANCE L←→R -22←0→+22 YES YES En-23

AUDIO INPUT1 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

AUDIO INPUT2 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

AUDIO INPUT3 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

IMAGE ADJUST ASPECT MODE NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE*

3

— YES En-23

V-POSITION ←→ -64←0→+64 YES YES En-23

H-POSITION ←→ -128←0→+127 YES YES En-23

V-HEIGHT ←→ 0←→64 YES YES En-23

H-WIDTH ←→ 0←→64 YES YES En-23

AUTO PICTURE OFF←→ON*

2

NO YES En-23

FINE PICTURE*

1

←→*

2

0←→64 YES YES En-23

PICTURE ADJ.*

1

←→*

2

0←→64 YES YES En-23

UNDERSCAN OFF←→ON YES NO En-23

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION1 OSM DISPLAY OSM OFF←→ON YES YES En-24

OSM ADJ. 1←

…

→6 YES YES En-24

OSM ANGLE H←→V YES YES En-24

OSM ORBITER OFF←→ON YES YES En-24

OSM CONTRAST LOW←→NORMAL YES YES En-24

BNC INPUT RGB←→COMP. YES YES En-24

D-SUB INPUT RGB — YES En-24

RGB SELECT AUTO YES YES En-24

HD SELECT 1080B/1035I/1080A NO YES En-25

INPUT SKIP OFF←→ON YES YES En-25

ALL RESET OFF←→ON — YES En-25

:Shaded areas indicate the default value.

←→

: Press the



or



button to adjust.

:Menu items in a ruled box are available when the ADVANCED OSM is set to ON.

Menu Tree

La page charge ...

NEC Computer Monitor 42XM5 Manuel utilisateur

Ce manuel convient également à

NEC Computer Monitor 42XM5 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents