Develco Motion Sensor Manuel utilisateur

Marque: Develco

Modèle: Motion Sensor

Catégorie: Cheminées

Taper: Manuel utilisateur

eng a.

c. g.

MOUNTING FLAT ON CEILING OR WALL

1. Open the casing, and use the sensor part

with oval holes to mark the screw holes on

the ceiling or the wall.

2. Mount the sensor on the wall or the ceiling

by installing one screw from the bag

marked “A” through each oval hole. Using

screws for mounting is the most secure

mounting option, as it prevents sudden,

unwanted removal.

• Place the sensor indoors at a temperature

between 0-50°C.

• Its angle of detection from above, the sides,

and below must be 45°.

• Place the Motion Sensor Mini in a location

with a clear view of the monitored area and

the windows.

• The distance from the sensor to a replace

or a stove must be at least four meters.

• The Motion Sensor Mini must be reachable

for battery testing and maintenance.

• Place the sensor free of curtains and other

obstacles.

• Avoid placing the Motion Sensor Mini close

to a heating/cooling source.

• Avoid placing the Motion Sensor Mini in

direct sunlight or bright light.

Product description

The compact Motion Sensor Mini allows you to

detect if somebody is in the room or not. With

the Motion Sensor Mini, you can set the light

to turn on and o as people come and go. The

motion sensor is PIR based and is able to sense

movement up to 9 meters from the sensor.

Motion Sensor Mini

Version 3.5

INSTALLATION MANUAL Placement

CORNER OR CEILING MOUNTING WITH

CORNER BRACKET

1. If you have a sensor with a corner bracket

included, you can mount the sensor with

this bracket in a corner or on the ceiling.

2. Use the corner bracket to mark the screw

holes on the two walls in the corner of the

room or on the ceiling.

3. Use the two screws in the bag marked “A”

to install the bracket in the marked place.

Using screws for mounting is the most

secure mounting option, as it prevents

unwanted removal, e.g. by intruders.

Alternatively, you can use the two small,

round pieces of double adhesive tape to

mount the bracket in the corner (do not

mount it on the ceiling with tape). Make sure

to press rmly on the bracket with the tape

to make it stick, and then attach the sensor

to the bracket.

Mounting

There are several mounting options for the

Motion Sensor Mini. You can mount it at on

a ceiling or wall, using the screws, adhesive

tape, or magnet. If you have a sensor with a

corner bracket included, you can mount the

bracket in corners or on the ceiling, using

screws or adhesive tape. Afterwards, you can

attach the sensor to the bracket by using the

magnet inside the device or the screws. If you

have a stand included, you can also place the

sensor on the stand.

When mounting with a corner bracket, you have

two options for mounting the sensor on the

bracket: either with the magnet or screws.

MOUNTING THE SENSOR ON THE CORNER

BRACKET WITH THE SCREWS

If you are using the sensor for security purposes,

we recommend using screws to mount the

sensor on the bracket for a more secure

fastening.

1. Open the casing of the sensor.

MOUNTING WITH MAGNET

If your sensor includes a corner bracket, you

can mount the sensor at on the wall or ceiling,

using the magnet from the bracket.

1. Unscrew the small magnet from the bracket.

2. Screw the magnet on a ceiling or a wall.

MOUNTING THE SENSOR ON THE CORNER

BRACKET WITH THE MAGNET

1. Open the casing of the sensor.

2. Insert batteries.

3. Close the casing of the sensor.

4. Attach the sensor to the corner bracket,

which includes a magnet.

3. Attach the sensor to the magnet.

Precautions

• When mounting with tape, make sure the

surfaces are clean and dry.

• When mounting with tape, the room

temperature should ideally be between 21°

C and 38° C and minimum 16° C.

• Avoid mounting with tape on rough, porous

or bered materials such as wood or

cement, as they reduce the tape bond.

2. Place the part with oval holes against the

already mounted bracket.

Alternatively, you can use the large, round

piece of double adhesive tape to mount

the sensor. Make sure to press rmly on the

sensor with the tape to make it stick, since

it is pressure-activated tape.

3. Insert batteries and make sure that the

battery polarity is correct (+/-).

4. Close the casing of the sensor.

Disclaimers

CAUTION:

• Choking hazard! Keep away from children.

Contains small parts.

• Please follow the guidelines thoroughly.

The Motion Sensor Mini is a preventive,

informing device, not a guarantee or

insurance that sucient warning or

protection will be provided, or that no

property damage, theft, injury, or any similar

situation will take place. Develco Products

cannot be held responsible in case any of

the above-mentioned situations occur.

Develco Products assumes no responsibility for

any errors, which may appear in this manual.

Furthermore, Develco Products reserves the

right to alter the hardware, software, and/

or specications detailed herein at any time

without notice, and Develco Products does

not make any commitment to update the

information contained herein. All the trademarks

listed herein are owned by their respective

owners.

Other certications

Zigbee Home Automation 1.2 certied.

Disposal

Dispose the product and battery properly at the

end of their lives. This is electronic waste, which

should be recycled.

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED)

2014/53/EU

• RoHS Directive 2015/863/EU amending

2011/65/EU

• REACH 1907/2006/EU + 2016/1688

IC statement

Distributed by Develco Products A/S

Tangen 6

8200 Aarhus N

Denmark

www.develcoproducts.com

ISED statement

Innovation, Science and Economic

Development Canada ICES-003 Compliance

Label: CAN ICES-3 (B)/NMB-3(B).

ISED statement

The device will blink twice every minute when

the battery is low.

Battery replacement

Resetting

Resetting is needed if you want to connect your

Motion Sensor Mini to another gateway, or if you

need to perform a factory reset to eliminate

abnormal behaviour.

4. While you are holding the button down, the

LED rst ashes once, then two times in a

row, and nally numerous times in a row.

5. Release the button while the LED is ashing

numerous times in a row.

6. After you release the button, the LED shows

one long ash, and the reset is completed.

Connecting

1. When batteries are inserted, the Motion

Sensor Mini will automatically start searching

(up to 15 minutes) for a Zigbee network to

join.

2. Make sure that the Zigbee network is open

for joining devices and will accept the Motion

Sensor Mini.

3. While the sensor is searching for a Zigbee

network to join, the LED ashes red.

Modes

SEARCHING GATEWAY MODE

Red LED light is ashing every second (up to 15

minutes).

LOW BATTERY MODE

The device will ash red twice every minute

when the battery is low.

STAND

1. If you have a sensor with

a plastic stand included,

you can insert the stand

in the opening on the

back of the sensor as

shown on the drawing.

2. Place the standing sensor

on the shelf or on a desk.

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular, its

compliance with the harmonized standards and

specications.

Fault nding

• In case of a bad or weak signal, change

the location of the Motion Sensor Mini.

Otherwise, you can relocate your gateway

or strengthen the signal with a smart plug.

• If the search for a gateway has timed out, a

short press on the button will restart it.

FCC statement

Changes or modications to the equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation.

STEPS FOR RESETTING

1. Detach the sensor from the bracket and/or

open the casing.

2. Check that the batteries are inserted

correctly.

3. Press and hold the round menu button

inside the device.

4. When the sensor is connected to a network, it

will stop ashing.

3. Take two screws from the bag marked “B”.

Mount one screw through each oval hole

and into two holes on the corner bracket.

4. Insert batteries and make sure that the

battery polarity is correct (+/-).

5. Close the casing of the sensor.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged to

try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The antenna used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located or

operating in conjunction with any other antenna

or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference, and

2. This device must accept any interference

received, including interference that may

cause undesired operation.

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20 cm between the radiator and your

body.

CAUTION:

• Do not attempt to recharge or open the

batteries.

• Risk of explosion if batteries are replaced by

an incorrect type.

• Dispose of a battery into re or a hot oven, or

mechanically crushing or cutting of a battery

can result in an explosion

• Leaving a battery in an extremely high

temperature surrounding environment can

result in an explosion or the leakage of

ammable liquid or gas.

• A battery subjected to extremely low air

pressure may result in an explosion or the

leakage of ammable liquid or gas

• Maximum operation temperature is 50°C /

122°F

• If you experience leakage from the batteries,

immediately wash your hands and/or any

aected area of your body thoroughly!

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components

1. To replace the battery, detach the Motion

Sensor Mini from the bracket and/or open

the casing.

2. Replace the battery respecting the polarities.

3. Close the casing of the sensor. inside.

ALARM TESTING MODE

The motion sensor will automatically ash

green every time movement is detected by the

Intruder Alarm System (IAS), no matter if the

alarm system is activated or deactivated. The

green ashes can help you determine if the

placement of the sensor is suitable for alarm

purposes.

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

Cet équipement est conforme aux limites

d’exposition aux radiations IC CNR-102 établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une

distance minimale de 20 cm entre le radiateur

et votre corps.

Develco Motion Sensor Manuel utilisateur

Marque: Develco

Modèle: Motion Sensor

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Develco Motion Sensor User manual

Develco Motion Sensor Manuel utilisateur

Develco Motion Sensor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents