Schumacher TY25865 John Deere 6V/12V Automatic Battery Charger with Engine Start JD-5050A Le manuel du propriétaire

2/10/50 Amp 6V/12V

Fully Automatic Battery

Charger With Engine

Start

OPERATOR’S MANUAL

TY25865 Battery Charger

OMTY25888 Issue 16Sep04 (ENGLISH/FRENCH)

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents are

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

If this product contains a gasoline engine:

WARNING

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth

defects or other reproductive harm.

The State of California requires the above two warnings.

John Deere Merchandise Division 00-99-000457/904

Litho in U.S.A.

Introduction

OUOD006,0000033 –19–29JUN04–1/2

Foreword

THANK YOU for purchasing a John Deere product.

READ THIS MANUAL carefully to learn how to operate

and service your battery charger correctly. Failure to

do so could result in personal injury or equipment

damage. This manual and safety signs on your battery

charger may also be available in other languages.

(See your John Deere dealer to order.)

THIS MANUAL SHOULD BE CONSIDERED a

permanent part of your battery charger and should

remain with the charger when you sell it.

MEASUREMENTS in this manual are given in both

metric and customary U.S. unit equivalents. Use only

correct replacement parts and fasteners.

WRITE PRODUCT INFORMATION in the Specification

section. Accurately record all the numbers to help in

tracing the battery charger should it be stolen. Your

distributor also needs these numbers when you order

parts. File the product information in a secure place.

WARRANTY is provided as part of John Deere’s

support program for customers who operate and

maintain their equipment as described in this manual.

The warranty is explained in the Warranty section at

the end of this manual.

OUOD006,0000033 –19–29JUN04–2/2

TYB4786 –UN–07SEP04

TY25865 Battery Charger

This warranty provides you the assurance that John

Deere will back its products where defects appear within

the warranty period. In some circumstances, John Deere

also provides field improvements, often without charge to

the customer, even if the product is out of warranty.

Should the equipment be abused, or modified to change

its performance beyond the original factory specifications,

the warranty will become void and field improvements

may be denied.

091604

PN=2

Contents

Page

Safety ................................05-1

Controls and Operation

Preparing Battery ........................10-1

Positioning Battery Charger ................10-2

Understanding Automatic Charging ..........10-3

Checking Battery State-of-Charge ...........10-4

Identifying Battery Reserve Capacity

(RC) Rating...........................10-4

Estimating Battery Recharge Time ...........10-5

Activating and Charging a Dry Battery ........10-6

Using DC Amps Meter During Charging .......10-7

Charging Battery Installed in Vehicle .........10-7

Charging Battery Outside of Vehicle.........10-10

Starting Engine.........................10-13

Troubleshooting

Troubleshooting Battery Charger ............15-1

Storage

Storing Battery Charger ...................20-1

Specifications

Battery Charger Specifications ..............25-1

Record Product Information ................25-1

Warranty

Warranty...............................30-1

All information, illustrations and specifications in this manual are based on

the latest information available at the time of publication. The right is

reserved to make changes at any time without notice.

COPYRIGHT

©

2004

DEERE & COMPANY

Moline, Illinois

A John Deere ILLUSTRUCTION

®

Manual

i

091604

PN=1

Contents

ii

091604

PN=2

Safety

DX,ALERT –19–29SEP98–1/1

Recognize Safety Information

T81389 –UN–07DEC88

This is a safety-alert symbol. When you see this symbol

on your machine or in this manual, be alert to the

potential for personal injury.

Follow recommended precautions and safe operating

practices.

DX,SIGNAL –19–03MAR93–1/1

Understand Signal Words

TS187 –19–30SEP88

A signal word—DANGER, WARNING, or CAUTION—is

used with the safety-alert symbol. DANGER identifies the

most serious hazards.

DANGER or WARNING safety signs are located near

specific hazards. General precautions are listed on

CAUTION safety signs. CAUTION also calls attention to

safety messages in this manual.

DX,READ –19–03MAR93–1/1

Follow Safety Instructions

TS201 –UN–23AUG88

Carefully read all safety messages in this manual and on

your machine safety signs. Keep safety signs in good

condition. Replace missing or damaged safety signs. Be

sure new equipment components and repair parts include

the current safety signs. Replacement safety signs are

available from your John Deere dealer.

Learn how to operate the machine and how to use

controls properly. Do not let anyone operate without

instruction.

Keep your machine in proper working condition.

Unauthorized modifications to the machine may impair the

function and/or safety and affect machine life.

If you do not understand any part of this manual and need

assistance, contact your John Deere dealer.

05-1

091604

PN=5

Safety

DX,SPARKS –19–03MAR93–1/1

Prevent Battery Explosions

TS204 –UN–23AUG88

Keep sparks, lighted matches, and open flame away from

the top of battery. Battery gas can explode.

Never check battery charge by placing a metal object

across the posts. Use a voltmeter or hydrometer.

Do not charge a frozen battery; it may explode. Warm

battery to 16°C (60°F).

DX,POISON –19–21APR93–1/1

Prevent Acid Burns

TS203 –UN–23AUG88

Sulfuric acid in battery electrolyte is poisonous. It is strong

enough to burn skin, eat holes in clothing, and cause

blindness if splashed into eyes.

Avoid the hazard by:

1. Filling batteries in a well-ventilated area.

2. Wearing eye protection and rubber gloves.

3. Avoiding breathing fumes when electrolyte is added.

4. Avoiding spilling or dripping electrolyte.

5. Use proper jump start procedure.

If you spill acid on yourself:

1. Flush your skin with water.

2. Apply baking soda or lime to help neutralize the acid.

3. Flush your eyes with water for 15—30 minutes. Get

medical attention immediately.

If acid is swallowed:

1. Do not induce vomiting.

2. Drink large amounts of water or milk, but do not

exceed2L(2quarts).

3. Get medical attention immediately.

05-2

091604

PN=6

Safety

DX,WEAR2 –19–03MAR93–1/1

Wear Protective Clothing

TS206 –UN–23AUG88

Wear close fitting clothing and safety equipment

appropriate to the job.

Operating equipment safely requires the full attention of

the operator. Do not wear radio or music headphones

while operating machine.

DX,MSDS,NA –19–03MAR93–1/1

Handle Chemical Products Safely

TS1132 –UN–26NOV90

Direct exposure to hazardous chemicals can cause

serious injury. Potentially hazardous chemicals used with

John Deere equipment include such items as lubricants,

coolants, paints, and adhesives.

A Material Safety Data Sheet (MSDS) provides specific

details on chemical products: physical and health hazards,

safety procedures, and emergency response techniques.

Check the MSDS before you start any job using a

hazardous chemical. That way you will know exactly what

the risks are and how to do the job safely. Then follow

procedures and recommended equipment.

(See your John Deere dealer for MSDS’s on chemical

products used with John Deere equipment.)

05-3

091604

PN=7

Safety

DX,DRAIN –19–03MAR93–1/1

Dispose of Waste Properly

TS1133 –UN–26NOV90

Recycle Waste

Improperly disposing of waste can threaten the

environment and ecology. Potentially harmful waste used

with John Deere equipment include such items as oil, fuel,

coolant, brake fluid, filters, and batteries.

Use leakproof containers when draining fluids. Do not use

food or beverage containers that may mislead someone

into drinking from them.

Do not pour waste onto the ground, down a drain, or into

any water source.

Air conditioning refrigerants escaping into the air can

damage the Earth’s atmosphere. Government regulations

may require a certified air conditioning service center to

recover and recycle used air conditioning refrigerants.

Inquire on the proper way to recycle or dispose of waste

from your local environmental or recycling center, or from

your John Deere dealer.

05-4

091604

PN=8

Safety

OUOD006,0000016 –19–16JUN04–1/1

IMPORTANT SAFETY INSTRUCTIONS- SAVE THESE INSTRUCTIONS

CAUTION: RISK OF EXPLOSIVE GASES.

Working in the vicinity of lead-acid batteries

is dangerous. Batteries generate explosive

gases during normal battery operation. Read

this manual and follow the instructions

exactly EACH TIME you use this battery

charger.

To reduce risk of battery explosion, follow

these instructions and the instructions

published by battery manufacturer. Review

the cautionary markings on the battery,

battery charger, and engine compartment.

WARNING: Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known by the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

1. SAVE THESE INSTRUCTIONS. This manual

contains important safety and operating instructions

for your battery charger. Read and understand this

manual before using the battery charger.

2. To reduce risk of electric shock, do not operate

battery charger when unit is exposed to water. Do

not expose battery charger to rain or snow.

3. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a

risk of fire, electric shock or injury to persons.

4. To reduce the risk of damage to electric plug and

cord, pull by plug rather than cord when

disconnecting battery charger.

5. Use of an extension cord is not recommended. Use

of an improper extension cord could result in fire or

electric shock. If an extension cord must be used,

make sure:

a. the pins on plug of extension cord are the same

number, size, and shape as those on plug of

charger,

b. the extension cord is properly wired and in good

electrical condition, and

c. the wire size is large enough for the length of

cord for the ampere rating of this battery charger

as specified below.

Length of Cord (Ft.) 25 50 100 150

AWG Size of Cord 18 18 16 14

6. Never alter AC cord or grounding plug provided. If

temporary adapter must be used to plug battery

charger into a two pole outlet, connect the

grounding hardware on the adapter to a properly

grounded outlet using the center screw of the outlet

plate. Be sure the center screw of the outlet plate is

grounded. Use of adapter plug NOT ALLOWED in

Canada.

7. Locate battery power cord so it cannot be stepped

on, tripped over, or subjected to damage or stress.

Do not operate battery charger with damaged cord

or plug. Replace cord or plug immediately.

8. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged

in any way. Take it to a qualified service technician.

9. Do not disassemble battery charger. Take charger

to a qualified service technician when service or

repair is necessary. Incorrect assembly may result

in electric shock or fire.

10. To reduce risk of electric shock, unplug battery

charger from outlet before attempting any

maintenance or cleaning.

05-5

091604

PN=9

Safety

OURGP12,000010C –19–02JUN04–1/1

Personal Precautions

1. Wear complete eye protection and clothing

protection. Avoid touching eyes when working near

batteries.

2. Have plenty of fresh water and soap nearby, in

case battery acid contacts skin, clothing, or eyes.

3. Someone should be within range of your voice or

close enough to come to your aid when you work

near a lead-acid battery.

4. Avoid touching eyes while working with battery. If

acid enters eye, immediately flood eye with running

cold water for 15—30 minutes and get medical

attention immediately. If battery acid contacts skin

or clothing, wash immediately with soap and water.

5. Batteries generate explosive gases! NEVER smoke

or allow a spark or flame in the vicinity of battery or

engine. Always operate battery charger in an open,

well ventilated area.

6. Do not drop a metal tool onto the battery. It might

spark or short-circuit the battery or other electrical

part that may cause an explosion.

7. Remove personal metal items such as rings,

bracelets, necklaces, and watches when working

near a lead-acid battery.

8. Use the battery charger for charging LEAD-ACID

batteries only. The charger is not intended to supply

power to a low voltage electrical system other than

in a starter-motor application. Do not use the

battery charger for charging dry-cell batteries that

are commonly used with home appliances. These

batteries may burst and cause injury to persons or

damage to property.

9. NEVER charge a frozen battery.

10. Never allow battery acid to drip on charger when

reading specific gravity or filling battery.

11. Never set battery on top of battery charger.

12. Neutralize acid spills thoroughly with baking soda

before attempting to clean up.

OURGP12,000010E –19–02JUN04–1/1

Battery Charger Connection Precautions

CAUTION: Connect and disconnect DC

clamps only after removing AC cord from

electrical outlet.

Never allow battery charger clamps to touch

each other.

Do not connect both battery charger clamps

directly to the battery.

1. Locate battery charger as far from battery as cables

permit.

2. When connecting battery charger, attach one clamp

to battery and the other clamp to a grounding point

away from the battery.

3. Read the Controls and Operation section before

connecting the battery charger.

4. When connecting each clamp, rock or twist the

clamp back and forth several times to make a good

connection. Do not twist or rock the first clamp after

the second clamp has been connected.

05-6

091604

PN=10

Safety

OUOD006,0000034 –19–29JUN04–1/1

Safety Sign

TYB4787 –UN–08SEP04

Safety Decal Location

TYB4787A –UN–07SEP04

Safety Decal

NOTE: Safety decal (A) is located on back of battery

charger.

05-7

091604

PN=11

Controls and Operation

OUOD006,000000E –19–15JUN04–1/1

Preparing Battery

CAUTION: A marine (boat) battery must be

removed and charged on shore. To charge it

onboard requires equipment specially

designed for marine use.

1. Make sure battery is a 6 volt or 12 volt lead-acid

battery.

2. Make sure all vehicle accessories are off.

3. If battery must be removed from vehicle to charge,

always remove grounded terminal from battery first.

4. Make sure area around battery is well ventilated.

Gases can be forcefully blown away using a piece

of cardboard or other nonmetallic material as a fan.

5. Study battery manufacturer’s specific precautions,

such as removing or not removing cell caps while

charging, and recommended rates of charge.

6. For batteries with removable vent caps, add distilled

water to each cell until battery acid reaches level

specified by battery manufacturer. Do not overfill.

7. Clean battery terminals.

10-1

091604

PN=12

Controls and Operation

OURGP11,00001A5 –19–27MAY04–1/1

Positioning Battery Charger

TS204 –UN–23AUG88

Risk of Battery Explosion

CAUTION: Risk of explosion. Battery gases

produced during charging can explode.

Ventilate area. Keep sparks and flames away.

1. Position the battery charger in a clean, dry, well

ventilated place as far from the battery as cables

permit.

2. Never place the battery charger directly above battery

being charged. Gases from battery will corrode and

damage charger.

3. Never allow battery acid to drip on battery charger

when reading gravity or filling battery.

4. Do not operate battery charger in a closed area, or

restrict ventilation in any way.

5. Do not set battery on top of battery charger or battery

charger on top of battery.

6. Position battery charger at least 46 cm (18 inches)

above floor.

10-2

091604

PN=13

Controls and Operation

OURGP12,0000053 –19–13AUG04–1/1

Understanding Automatic Charging

NOTE: Automatic charging applies to 6 volt and 12

volt batteries.

In automatic charge mode, the battery charger will

monitor battery charge voltage and stop charging when

full charge voltage is sensed. If the battery voltage

drops below full charge, then the charger will start

again. The charger does not select charge rate. High

charge rates may damage smaller batteries.

Low charge rates will produce the most complete

recharge, but will take longer than high charge rates.

Higher charge rates will recharge the battery faster,

but there is a risk of battery damage due to

overcharge.

A charge current that is 3% of the battery’s CCA rating

is a good starting charge rate. For example, a battery

with a 500 CCA rating would have a charge rate of 15

amps (500 amps x 3% = 15 amps).

A charge current that is 1% of the battery’s CCA rating

will not produce overcharge, and the battery can be

charged for extended time periods without damage.

For example, a battery with a 950 CCA rating could

have a charge rate of approximately 10 amps (950 x

1% = 9.5 amps) for extended periods without risk of

overcharge.

The charge current that a battery will accept is

dependent on the charge rate setting and the battery’s

state of charge and history.

A battery that has been recently and rapidly

discharged (lights left on overnight) will readily accept

recharge and will exhibit high recharge currents that

decline steadily as the battery recharges.

A battery that has been slowly discharged over a long

time period (slow discharge over a number of months,

also known as sulfated), will not initially accept high

charge currents. Even at high charge rate settings, the

charge currents will start low and then increase to a

peak before tapering off as the battery recharges.

10-3

091604

PN=14

Controls and Operation

OUOD006,0000057 –19–17AUG04–1/1

Checking Battery State-of-Charge

TYK275 –UN–08OCT96

Checking State-of-Charge

A—Hydrometer

Use a voltmeter or hydrometer (A) to determine state-of

charge. Refer to chart to obtain percent of charge.

Voltmeter Reading Hydrometer Battery Test

Reading Reading

12 Volt Battery* Specific Gravity Percent of Charge

12.4 or greater 1.265 100%

12.39 to 12.25 1.225 75%

12.24 to 12.10 1.190 50%

12.09 to 11.96 1.155 25%

11.95 to 0 1.120 0%

* 6 volt battery voltmeter readings are one-half of 12 volt

battery readings shown.

CAUTION: Do NOT attempt to charge a frozen

battery.

NOTE: Any battery 25% charged or less may readily

freeze and should be charged at once.

OUOD006,0000059 –19–18AUG04–1/1

Identifying Battery Reserve Capacity (RC) Rating

Typical Group Sizes Auto, LGC, etc. 3ET, 47, 48, 49 31, 30H 1, 2 5D, 4 4D, 3EH, 8D

Reserve Capacity 80 or less 81-125 126-180 181-260 261 or more

Rating

Time needed to completely recharge a battery

depends on the battery’s electrical capacity and

present state of charge. Battery electrical reserve (RC

rating) is given in minutes, and is needed when

estimating recharge time.

Most batteries have a label attached showing the

battery’s type and/or reserve capacity rating. If this

information is not found on the battery, use the above

chart to determine reserve capacity (RC) rating.

10-4

091604

PN=15

Controls and Operation

OUOD006,000005A –19–18AUG04–1/1

Estimating Battery Recharge Time

TYB4797 –19–18AUG04

Estimating Recharge Time

1. Use table to determine time needed to completely

recharge battery based on battery type, present state

of charge, and charging rate (amps).

2. If recharge time cannot be estimated from the table,

calculate recharge time using the following formula:

Recharge capacity (minutes) x 0.6 x 1.25 ÷ charge rate

(amps) = approximate hours needed to recharge a

totally discharged battery.

EXAMPLE:

80 x 0.6 x 1.25 ÷ 10 = 6 hours

NOTE: Example uses an 80 minute reserve capacity

battery and 10 amp charge rate.

When battery is not totally discharged, adjust charge

time estimate using % DISCHARGED figure for

calculation.

EXAMPLE:

6 hours x 0.75 = 4.5 hours

NOTE: Example shows adjusted time when battery is

25% charged (75% discharged). If battery was

75% charged, discharged figure of 0.25 would be

used in adjusted calculation to arrive at 1.5 hours.

10-5

091604

PN=16

Controls and Operation

OUOD006,0000058 –19–17AUG04–1/1

Activating and Charging a Dry Battery

Listed below are six steps to activate a dry-charged

battery.

1. Remember Safety. Always wear protective

glasses, gloves, and clothing when handling

batteries and sulfuric acid electrolyte.

2. Prepare the Battery. Remove vents and date code

punch outs. If the battery or electrolyte is below

60°F, activation will be slower.

3. Add Electrolyte. Fill each cell with electrolyte until

the level just touches the bottom of the “split vent”

at the bottom of the vent well. Do not over fill by

covering the split. If the split is covered, the gases

created during charging will not escape properly,

and will cause increased splashing and acid loss.

Under filling can reduce the performance and life of

the battery.

4. Let the Battery Absorb the Acid. It takes time for

the battery plates and separators to absorb the

acid. A 15 to 30 minute stand time before charging

is recommended. Gentle rocking of the battery will

help dislodge trapped air bubbles.

5. Charge the Battery. Charge the activated battery

to ensure that it starts its life at 100%

state-of-charge. Activated batteries should be

charged at no more than 1% of CCA for 30

minutes, and up to 6 hours in cases of extremely

high humidity storage. For example, a 625 CCA

battery should be charged at 6 amps. Reduce the

charging rate if excessive gassing occurs.

Charging is recommended when:

a. The voltage of the activated battery is below

12.4 volts, even after 15 minutes stand time.

b. The battery will not be installed within the next

30 days.

c. The outside temperature is below 32°F.

d. The battery has been in storage for more than

two years.

6. Top off the Electrolyte Level. Add electrolyte as

required to bring the level back up to the bottom of

the split vent in the bottom of the vent well. The

acid level may have dropped due to absorption into

the plates and separators. Replace the service

vents.

Service hints for longer battery life:

• Add only pure drinking water or distilled water to the

battery after it is placed in service.

• Disconnect the ground cable when the vehicle is

stored for more than three months. Cleaning the

battery top, adding water, and charging the battery

before vehicle storage will reduce discharge and

sulfation battery failures.

• Specific gravity is the best indicator of battery

state-of charge.

10-6

091604

PN=17

Controls and Operation

OURGP12,0000052 –19–12AUG04–1/1

Using DC Amps Meter During Charging

TYB4796 –UN–31AUG04

DC Amps Meter

A—Green LED

The DC Amps Meter indicates amount of amperes being

drawn by the battery. When initially charging a battery at

the 10 amp charging rate, the reading will be high, with

the needle near 10 amps. As the battery charges, the

needle will begin to fall. When the battery is fully charged,

the needle will point to 0 and the “FULL CHARGE” green

LED (A) will glow.

The “CHARGE %” scale simplifies reading the battery

state of charge. It is scaled for use with the 10 amp

charge rate. Percent of charge is based on current drawn

by the battery. Accuracy will vary with battery size and

type.

For the 2 amp charge rate, use the small red triangle for

reference. When initially charging at the 2 amp rate, the

needle will begin at the right side of the triangle, and will

fall to the left side, pointing to 0 when the battery is fully

charged.

OUOD006,0000035 –19–29JUN04–1/4

Charging Battery Installed in Vehicle

CAUTION: Risk of explosion. Battery gases

produced during charging can explode.

Ventilate area. Keep sparks and flames

away.

Stay clear of fan blades, belts, pulleys, and

other parts that can cause injury.

NEVER charge a frozen battery.

A marine (boat) battery must be removed

and charged on shore. To charge it onboard

requires equipment specially designed for

marine use.

WARNING: Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known by the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

IMPORTANT: DO NOT plug battery charger into

power receptacle or set any charger

controls until ALL connections have

been made.

Turn all vehicle switches OFF

(ignition, lights, radio, etc.) before

connecting battery charger.

1. Position AC and DC cords to reduce risk of damage

by hood, door, or moving engine parts.

2. Determine which battery terminal is the POSITIVE

terminal. (The Positive terminal may be identified

with a POS, P, or +, and usually has a larger

diameter than the Negative terminal (NEG, N, —).

3. Determine which battery terminal is grounded

(connected) to the chassis.

10-7

091604

PN=18

Continued on next page

Controls and Operation

OUOD006,0000035 –19–29JUN04–2/4

TYB4726 –UN–25JUN04

Negative Ground Connections

A—Positive (Red) Clamp

4. Connect one clamp of the battery charger to the

UNGROUNDED battery terminal using (a) or (b) below:

a. Negative-Grounded Vehicles: Connect Positive

(red) clamp (A) of battery charger to Positive

(Ungrounded) battery terminal.

b. Positive-Grounded Vehicles: Connect Negative

(black) clamp of battery charger to Negative

(Ungrounded) battery terminal.

NOTE: Rock or twist clamp back and forth several times

to make a good connection.

IMPORTANT: Do not connect ground clamp to the

carburetor, fuel lines, or sheet metal

body parts.

5. Connect remaining battery charger clamp to a

heavy-gauge metal part of vehicle chassis or engine

block, as far from battery as possible.

6. Plug battery charger AC power cord into 120-volt AC

receptacle.

Continued on next page

10-8

091604

PN=19

Controls and Operation

OUOD006,0000035 –19–29JUN04–3/4

TYB4788 –UN–07SEP04

TY25865 Control Panel

B—Battery Type Selector Switch

C—Charge Rate Selector Switch

D—DC Amps Meter

7. Select 6 volts or 12 volts to match battery type with

battery type selector switch (B).

8. Select charging amps with charge rate selector switch

(C) as follows:

• 2 amps (2A)- for small batteries commonly used in

garden tractors, snow mobiles, and motorcycles. Not

for use as trickle charger or for larger batteries.

• 10 amps (10A)- for automotive, marine, and deep

cycle batteries. Not for industrial applications.

9. Observe DC Amps meter (D) to determine charging

progress after charging has begun. (See “Using DC

Amps Meter During Charging” near beginning of this

section.)

Refer to following Charge Rate Table for approximate

charging time for charge rate selected

NOTE: When charging is completed, the needle will point

to 0, the “FULL CHARGE” green LED will glow,

and battery charger will turn off. Battery charger

turns back on if battery voltage falls below 6.5/13

volts on 6V/12V batteries respectively.

CHARGE RATE/CHARGE TIME

BATTERY SIZE/RATING

(HOURS)*

2 AMP 10 AMP

SMALL 6-12 AH 2 - 4 NR

BATTERIES 12-32 AH 4 - 10 NR

200-315 CCA 40-60 RC 11 - 14 2 - 2-7/8

315-550 CCA 60-85 RC 14 - 18 2-7/8 - 3-3/4

550-1000 18 - 35 3-3/4 - 7

85-190 RC

CCA

80 RC 18 3-1/2

MARINE/ 140 RC 27 5-1/2

DEEP CYCLE 160 RC 30 6

180 RC 33 7

* - Based on battery at 50% charge.

AH - Amp Hours

NR - Not Recommended

CCA - Cold Cranking Amps

RC - Reserve Capacity

10-9

091604

PN=20

Continued on next page

La page charge ...

Schumacher TY25865 John Deere 6V/12V Automatic Battery Charger with Engine Start JD-5050A Le manuel du propriétaire

Schumacher TY25865 John Deere 6V/12V Automatic Battery Charger with Engine Start JD-5050A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents