Ideal 61-637 Manuel utilisateur

Instrucciones en español adentro / Instructions en français à l’intérieur

61-637 Single Range

24 to 600V AC NCVT with Flashlight

61-627 Single Range

50 to 600V AC NCVT

Operation and Safety Manual

IDEAL

®

Test and Measurement

Notes

Table of Contents

3

Introduction ...................................................................... 4

Contacting IDEAL INDUSTRIES, INC ......................................... 4

Safety Information .............................................................. 5

Warnings ...................................................................................................5-6

Cautions .......................................................................................................6

Symbols ....................................................................................................... 7

Operation..................................................................... 8-14

Identification and description of operating controls and functions ............8-9

Operating Features ..................................................................................... 10

Tester Operation ......................................................................................... 11

Checking for The Presence of AC Voltage .................................................. 12

61-637 NCV Sensing Indications Table ......................................................13

61-627 NCV Sensing Indications Table ......................................................13

Functions Operation Table .......................................................................... 13

Functions Indication Table .........................................................................14

Electrical Specifications ............................................................................. 14

Environmental Specifications ................................................14

Mechanical Specifications ...................................................15

EMC / EMI .......................................................................15

FCC ............................................................................15

Safety ............................................................................15

Maintenance and Service ....................................................16

Disposal and Warranty ........................................................17

Introduction

The IDEAL 61-637 and 61-627 Single Range Non-Contact Voltage Testers

automatically detect and indicate the presence of voltage within specified ranges.

The 61-637 detects voltage within a range of 24-600V AC and the 61-627 detects

voltage within a range of 50-600V AC. Both testers provide non-contact detection

of voltage through an antenna enclosed in plastic at the tip of the tester which

senses the presence of the electromagnetic field present around live conductors.

The 61-637 has a flash light that works independently of the testing function and is

activated by an independent On/Off button.

Contacting IDEAL INDUSTRIES, INC.

To contact IDEAL INDUSTRIES, INC., call one of the following telephone numbers:

IDEAL Industries USA Customer Service

• Phone Number: 800-435-0705

• Email: [email protected]

IDEAL Industries Canada Customer Service

• Phone Number: 905-683-3400

• Email: [email protected]

IDEAL Industries EMEA

• Phone Number: +44 (0)1925 444 446

• Email: eur[email protected]

IDEAL Industries Australia

• Phone Number: +61 3 9562 0175

• Email: [email protected]

Or visit the IDEAL Electrical Website at www.idealind.com

To register your product, find manuals, watch videos, simply scan this QR code.

4

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E. Read and fully understand the

instruction manual prior to using this product. Failure to comply can result in

serious injury or death.

To contact IDEAL INDUSTRIES, INC., call one of the following telephone numbers:

IDEAL Industries USA Customer Service

• Phone Number: 800-435-0705

• Email: [email protected]

IDEAL Industries Canada Customer Service

• Phone Number: 905-683-3400

• Email: [email protected]

IDEAL Industries EMEA

• Phone Number: +44 (0)1925 444 446

• Email: eur[email protected]

IDEAL Industries Australia

• Phone Number: +61 3 9562 0175

• Email: [email protected]

Or visit the IDEAL Electrical Website at www.idealind.com

To register your product, find manuals, watch videos, simply scan this QR code.

Warning - Identifies conditions and actions that could result in

possible death or serious injury if the hazard is realized.

Caution - Identifies conditions and actions that could result in tester dam-

age, equipment under test damage or data loss if the hazard is realized.

WARNING

Safety Information

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E and follow the guidelines below and

the instructions in this manual when operating the tester. Failure to comply can

result in serious injury or death.

• Choking Hazard, Small Parts. Keep Away from Children Sharp Objects

Hazard, This is not a toy. It is not for use or play by children. Keep

Away from Children. Failure to do so can result in serious injury.

• Only experienced or technically competent consumers should use this

equipment. When in doubt, call an experienced electrician to make any and

all necessary repairs or installations. At all times, perform any necessary

work on a de-energized circuit that has had its circuit breaker turned off and

has been locked out.

• Use the Tester only as specified in this manual or protection provided by the

Tester can be compromised.

• Before using the Tester, visually inspect it to ensure the case or tip are not

cracked and the battery cap is securely in place. Do not use if the Tester

appears damaged.

• When using the tester, keep fingers behind the tactile barrier at the base of

the tester. (see #4 on page 9)

• This Tester is intended for use by qualified electricians and competent

consumers. Follow NFPA 70E Standards for Electrical Safety when using

this Tester.

• Do not use without the batteries correctly in place and the slide on battery

cover secured.

• Do not use Tester if it operates incorrectly as protection may be

compromised. When in doubt, have the Tester serviced.

5

• Have the Tester serviced only by qualified service personnel.

• Do not use the Tester around explosive gas, dust, or vapor, or during electrical

storms, or in wet environments.

• Do not apply more than the rated voltage, as marked on the Tester. Observe

CAT Rating of Tester when in use.

• To avoid false readings that can lead to electrical shock and injury, replace the

batteries as soon as the low battery indication appears.

• Voltages exceeding 30VAC or 60VDC pose a shock hazard so use caution.

• Do not work alone so that assistance can be rendered in an emergency.

• Use extreme caution when working around bare conductors or bus bars.

Contact with the conductor could result in electric shock.

• Adhere to local and national safety codes. Individual protective equipment

must be used to prevent shock and arc blast injury where hazardous live

conductors are exposed.

• Cancer and Reproductive Harm - www.P65Warnings.ca.gov

6

CAUTION

WARNING

Arc Flash and Shock Hazard, Proper PPE Required. Follow all safety procedures,

wear proper PPE in accordance to NFPA 70E and follow the guidelines below and

the instructions in this manual when operating the tester. Failure to comply can

result in serious injury or death.

Tester damage can occur if the following guidelines are not adhered to.

• Use the proper settings and voltage ratings for the measurement application.

• Clean the case and accessories with a damp cloth and mild detergents only.

Do not use abrasives or solvents. Make sure the tester is completely dry

before use.

• Not intended for insertion into electrical outlet slots.

• Do not apply excessive side or torsional loading to the sensing tip as

damage may occur.

SYMBOL DESCRIPTION

Arc Flash and Shock Hazard

Shock Hazard

Warning or Caution

Choking Hazard

AC (Alternating Current)

Earth Ground

CAT III

IEC Measurement Category III

CAT III has protection against transients in equipment in fixed-

equipment installations such as distribution panels feeders,

and short branch circuits. Also included are lighting systems in

larger buildings.

CAT IV

IEC Measurement Category IV

CAT IV has protection against transients from the primary

supply level such as a Meter or overhead or underground utility

service.

V

Voltage AC

Double Insulation

Do not dispose of this product as unsorted municipal waste.

It must be properly disposed of in accordance with local

regulations. Please see www.epa.gov or www.erecycle.org for

additional information.

Conforms to applicable North American Safety Standards

Conforms to applicable Australian Safety Standards

Conforms to European Directives

Symbols & Descriptions

NOTE: Tester must be used within the designated CAT Rating.

7

Identification and Description of Operating

Functions for the 61-637 Single Range 24

to 600V AC NCVT w/ Flashlight and 61-627

Single Range 50 to 600V AC NCVT:

1. Power On/Off button

2. Audible Notification On/Off button (61-637 Only)

3. Flashlight On/Off button (61-637 Only)

4. Tactile Barrier

5. Non-Contact Voltage Sensing Tip

6. Flashlight (61-637 Only)

7. Pocket Clip

8. Battery Cover Locking Point

9. Battery Cover Release Point

10. Lanyard Tie Off Point

11. Battery Cover

8

Operation

1. Power On/Off button

2. Audible Notification On/Off button (61-637 Only)

3. Flashlight On/Off button (61-637 Only)

4. Tactile Barrier

5. Non-Contact Voltage Sensing Tip

6. Flashlight (61-637 Only)

7. Pocket Clip

8. Battery Cover Locking Point

9. Battery Cover Release Point

10. Lanyard Tie Off Point

11. Battery Cover

9

1

3

4

5

6

7

2

8

10

9

11

10

Operating Features

Audible Notification Disable (61-637 Only)

The tester can be operated with a visual only indication of voltage when working in

noise sensitive/noise restricted areas. With the tester On, press the Speaker button

for less than 1s. The tester will beep once to indicate the audible warning is muted

and only a visual indication will be provided. To restore the audible warning, press

the speaker button for less than 1s. The tester will beep twice to indicate the audible

warning is active and both a visual and audible indication will be provided. The

tester is set to Audible Notification On as the default setting.

Flashlight (61-637 Only)

An LED Flashlight in the tip operates independently of the tester functions and can

be used to illuminate the work area. Press the Flashlight Button to turn it On/Off.

The tester is set to Flashlight Off. The Flashlight will Auto Power Off after 5 minutes

of no voltage detection. Further voltage detection will reset the APO function to 5

minutes again.

Note: Use of the flashlight will decrease battery life.

Auto Power Off

After 10 minutes of inactivity (no button pressed and no signals detected), the

tester will emit one long beep (~0.5s) and then shut off. Note: if the flashlight is on,

it will be also shut off.

Low Battery Indication

If battery voltage is less than around 2.4V, the green led in the tip will flash 3 times

and the buzzer will send out one long beep, then turn off the device.

Turning The Tester On

Press the Power On/Off button for less than 1s to turn the tester On. The tester

will beep twice, and will light a steady Green LED in the tip of the tester to indicate

Power On.

Turning The Tester Off

Press the Power On/Off button for more than 1s to turn the tester Off. Listen for a

long steady beep (~.5s) and watch for LED in the tip to turn off. The tester is now

deactivated and is not operational.

11

Tester Operation

Steady Green LED in the tip

indicates power-on

Checking for The Presence of AC Voltage

Prior to use, test on known live circuit to verify tester functionality. Place tip of the

tester near an AC voltage source and refer to the NCV Sensing Indications Table for

tester indication during operation.

Flashing Red LED in the tip and

intermittent beeping indicate

voltage is present. (See NCV

Sensing Indications table for

indications associated with each

range and mode setting)

12

While the NCV is a helpful function, it is ALWAYS RECOMMENDED that the

operator verify that any electrical conductor is completely deenergized and that

no voltage is present by measuring for voltage AND CONFIRMING THAT NO

VOLTAGE IS PRESENT and that all applicable PPE and lock out tag out procedures

be followed before attempting any work on ANY electrical distribution system.

Voltages with frequencies higher than 60Hz or electrostatic charges may also be

detected by the NCV sensing antenna. Due to the variability of designs across

device manufactures the 61-627 and 61-637 may not detect the presence of voltage

in Tamper Resistant Outlets.

NCV

Indications

Ranges (V AC)

Mode

18-25V 26-34V 35-45V 46-54V 55-600V

Normal Mode

(24-600V AC)

Red

Flashing

Light in Tip

and beeps

@ 2Hz

Red

Flashing

Light in

Tip and

beeps

from 2Hz

to 4Hz

Red

Flashing

Light in Tip

and beeps

@ 4Hz

Red

Flashing

Light in Tip

and beeps

from 4Hz

to 12 Hz

Red Flashing

Light in Tip

and beeps

@ 12Hz

Audible

Notification

Disabled

(24-600V AC)

Red

Flashing

Light in Tip

@ 2Hz, No

beeps

Red

Flashing

Light in

Tip from

2Hz to

4Hz, No

beeps

Red

Flashing

Light in Tip

@ 4Hz, No

beeps

Red

Flashing

Light in Tip

from 4Hz

to 12Hz,

No beeps

Red Flashing

Light in Tip

@ 12Hz, No

beeps

Indication Response Default Function Operation

On Off Meter On GREEN LED Push Button

Audible

(61-637 Only)

Beeps On Push Button

Flashlight

(61-637 Only)

Flashlight On Off Push Button

Functions Operation Table

13

61-637 NCV Sensing Indications Table

NCV

Indications

Ranges (V AC)

Mode

50-600V AC

Normal Mode

(50-600V AC)

Red Flashing Light in Tip and beeps @ 12Hz

61-627 NCV Sensing Indications Table

Note: Indications above may be subject to variability caused by humidity, insulation

thickness, distance, and other factors.

Note: Indications above may be subject to variability caused by humidity, insulation

thickness, distance, and other factors.

Functions Indication Table

Function Description

Power On Steady Greenlight in Tip,

2 Short Beeps

Power Off No Light, Long Beep

Tester Auto Power Off Green Light Flashes, 1 Beep

Audible OFF

(61-637 Only)

One Beep

Audible ON

(61-637 Only)

Two Beeps

Flashlight Button

(61-637 Only)

Flashlight On or Off

Electrical Specifications

Function Range

AC Voltage Sensing 61-637 24V AC to 600V AC

AC Voltage Sensing 61-627 50V AC to 600V AC

Frequency 50Hz or 60Hz AC

14

Environmental Specifications

Operating Temperature: 32ºF to 104ºF (0ºC to 40ºC) (<80%RH)

Operating Altitude:

6500 ft (2000 m)

Storage Temperature:

14ºF to 122ºF (-10ºC to 50ºC) (<80%RH)

Intended for indoor use.

Functions Indication Table

Function Description

Power On Steady Greenlight in Tip,

2 Short Beeps

Power Off No Light, Long Beep

Tester Auto Power Off Green Light Flashes, 1 Beep

Audible OFF

(61-637 Only)

One Beep

Audible ON

(61-637 Only)

Two Beeps

Flashlight Button

(61-637 Only)

Flashlight On or Off

Electrical Specifications

Function Range

AC Voltage Sensing 61-637 24V AC to 600V AC

AC Voltage Sensing 61-627 50V AC to 600V AC

Frequency 50Hz or 60Hz AC

Environmental Specifications

Operating Temperature: 32ºF to 104ºF (0ºC to 40ºC) (<80%RH)

Operating Altitude:

6500 ft (2000 m)

Storage Temperature:

14ºF to 122ºF (-10ºC to 50ºC) (<80%RH)

15

Mechanical Specifications

Dimensions: (L x W x H) 6.0 in. x 1.0 in. x 1.1 in.

(154 mm x 26 mm x 29 mm)

Weight: 0.13 LBS (0.06 KG)

Power Source: (2) 1.5V AAA Batteries

Flashlight:

(61-637)

>500LUX @ 4 in

EMC/EMI

CISPR 22 3rd Edition. Class B Limits.

EN 55032

CISPR 32

CISPR 11

FCC 15. 107 with reference to Section 15.109 (g).

ICES-003

EN 61326-2-2 Sec 6.4.2.101

USA (FCC)

47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.

Safety

Complies with the following:

IEC 61010-1, Edition 3 (2010-06) +AMD1 (2016-12)

ANSI/UL/IEC EN 61010-1, Edition 3 (2016-04-29)

CSA-C22.2 No. 61010-1-12 Edition 3 (2019-07-19)

IEC 60529

Overvoltage CAT IV 600V.

Any voltages exceeding the defined maximum voltage measurement categories

described above are outside the normal use of the equipment and protection cannot

be guaranteed.

Pollution Degree Class 2

16

Tester Inspection

Before using the Tester, visually inspect it to ensure the case or tip are not cracked

and the battery cover is securely locked in place. Do not use if the Tester appears

damaged.

Battery Inspection/Replacement

Maintenance and Storage

When not in use, turn the meter off. If the tester will not be used

for more than a month remove the batteries for storage. Clean the

case with a damp cloth and mild detergent. Do not use abrasives or

solvents. If the meter is exposed to water ensure the tester is

completely dry before use. Do not expose to chemicals or solvents.

Service and Replacement Parts

This unit has no user-serviceable parts.

Maintenance and Service

In order to preserve, protect and improve the quality of the environment, protect

human health and utilize natural resources prudently and rationally, the user should

return unserviceable product to relevant facilities in accordance with statutory

regulations. The crossed-out wheeled bin indicates the product needs to be

disposed separately and not as municipal waste.

Do not dispose of this product as unsorted municipal waste. It must be properly

disposed of in accordance with local regulations. Please see www.epa.gov or www.

erecycle.org for additional information.

The user is legally obliged to return used batteries and accumulators. Disposing

used batteries in household waste is prohibited! Batteries/accumulators containing

hazardous substances are marked with the crossed-out wheeled bin. The symbol

indicates that the product is forbidden to be disposed via domestic refuse. The

chemical symbols for the respective hazardous substances are Cd = Cadmium,

Hg = Mercury, Pb = Lead.

You can return used batteries/accumulators free of charge to any collecting point

of your local authority, our stores, or where batteries/accumulators are sold.

Consequently, you must comply with your legal obligations and contribute to

environmental protection.

Disposal of Waste, Electrical & Electronic Equipment

TWO YEAR LIMITED WARRANTY

This tester is warranted to the original purchaser against defects in material and

workmanship for a period of two (2) years from date of purchase. With proof of

purchase from an authorized IDEAL distributor, a defective tester will be repaired or

replaced with the same product or a functionally equivalent product, at the option

of IDEAL INDUSTRIES, INC. during the warranty period, subject to verification

of the defect or malfunction. Warranty does not cover consumables such as

fuses, batteries, and excludes defects caused by leakage from batteries, abuse,

mishandling, dropping, ordinary wear and tear, misuse, neglect, unauthorized

repair, improper use, alterations, accidents or any causes beyond IDEAL’s

reasonable control. Consequential or incidental damages are not recoverable under

this warranty. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you.

This LIMITED WARRANTY gives you specific legal rights, which vary from state to

state. This warranty constitutes the sole and exclusive remedy of the purchaser and

the exclusive liability of IDEAL, and is in lieu of any and all other warranties, and

expressly disclaims all other warranties, implied, or statutory as to merchantability,

fitness for purpose sold, description, quality productiveness, or any other matter.

No agent, distributor or other supplier has the authority to modify or amend this

warranty or make other representations or warranties other than those contained

in this warranty without express written authorization from IDEAL. For warranty

service, call IDEAL customer service at 1-800-435-0705.

Made in China.

17

Disposal of Used Batteries/Accumulators

IDEAL INDUSTRIES, INC. Sycamore, IL 60178, U.S.A. 800-435-0705 www.Idealind.com ND 9111-1

Scan the barcode on the right to see the new IDEAL T&M Product Line

Instrucciones en español adentro / Instructions en français à l’intérieur

61-637 Rango Singular

24 a 600V CA NCVT con Linterna

61-627 Rango Singular

50 a 600V CA NCVT

Manual de Operación y Seguridad

IDEAL

®

Prueba y Medición

Notas

La page charge ...

Ideal 61-637 Manuel utilisateur

Ce manuel convient également à

Ideal 61-637 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents