Black & Decker Powerful Solutions KS1301 Manuel utilisateur

Marque: Black & Decker

Modèle: Powerful Solutions KS1301

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

KS1300

KS1301

www.blackanddecker.ae

ENGLISH

30 29 10

25 27 28

ENGLISH

Intended use

Your Black & Decker saw has been designed for

sawing wood and wood products. This tool is

intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and

all instructions. Failure to follow the

warnings and instructions listed below may

result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in all of the warnings

listed below refers to your mains operated

(corded) power tool or battery operated

(cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c. Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

e. When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b. Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes,

hard hat, or hearing protection used for

appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

ENGLISH

d. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power

tool may result in personal injury.

e. Do not overreach. Keep proper footing and

balance at all times. This enables better

control of the power tool in unexpected

situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes,

jewellery or long hair can be caught in

moving parts.

g. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b. Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

c. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk

of starting the power tool accidentally.

d. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁed

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional power tool safety

warnings

Warning! Additional safety warnings for

saws

a. Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are

holding the saw, they cannot be cut by the

blade.

b. Do not reach underneath the workpiece. The

guard cannot protect you from the blade

below the workpiece.

ENGLISH

c. Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the

blade teeth should be visible below the

workpiece.

d. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the

work properly to minimize body exposure,

blade binding, or loss of control.

e. Hold power tool by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Contact with a "live"

wire will also make exposed metal parts of

the power tool "live" and shock the operator.

f. When ripping always use a rip fence or

straight edge guide. This improves the

accuracy of cut and reduces the chance of

blade binding.

g. Always use blades with correct size and

shape (diamond versus round) of arbour

holes. Blades that do not match the

mounting hardware of the saw will run

eccentrically, causing loss of control.

h. Never use damaged or incorrect blade

washers or bolt. The blade washers and bolt

were specially designed for your saw, for

optimum performance and safety of

operation.

Further safety instructions for

all saws

Causes and operator prevention of kickback:

• Kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the

workpiece toward the operator.

• When the blade is pinched or bound tightly by

the kerf closing down, the blade stalls and the

motor reaction drives the unit rapidly back

toward the operator.

• If the blade becomes twisted or misaligned in

the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood

causing the blade to climb out of the kerf and

jump back toward the operator.

Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a. Maintain a ﬁrm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but

kickback forces can be controlled by the

operator, if proper precautions are taken.

b. When the blade is binding, or when

interrupting a cut for any reason, release the

trigger and hold the saw motionless in the

material until the blade comes to a complete

stop. Never attempt to remove the saw from

the work or pull the saw backward while the

blade is in motion or kickback may occur.

Investigate and take corrective actions to

eliminate the cause of blade binding.

c. When restarting a saw in the workpiece,

centre the saw blade in the kerf and check

that saw teeth are not engaged into the

material. If saw blade is binding, it may walk

up or kickback from the workpiece as the saw

is restarted.

d. Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both

sides, near the line of cut and near the edge

of the panel.

ENGLISH

e. Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

f. Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

g. Use extra caution when making a "plunge

cut" into existing walls or other blind areas.

The protruding blade may cut objects that

can cause kickback.

Safety instructions for circular saws with outer or

inner pendulum guards and with tow guard

a. Check lower guard for proper closing before

each use. Do not operate the saw if lower

guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and

make sure it moves freely and does not

touch the blade or any other part, in all

angles and depths of cut.

b. Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. Lower guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c. Lower guard should be retracted manually

only for special cuts such as "plunge cuts"

and "compound cuts". Raise lower guard by

retracting handle and as soon as blade

enters the material, the lower guard must be

released. For all other sawing, the lower

guard should operate automatically.

d. Always observe that the lower guard is

covering the blade before placing saw down

on bench or ﬂoor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of

the time it takes for the blade to stop after

switch is released.

Additional safety instructions

for all saws with riving knife

a. Use the appropriate riving knife for the blade

being used. For the riving knife to work, it

must be thicker than the body of the blade but

thinner than the tooth set of the blade.

b. Adjust the riving knife as described in this

instruction manual. Incorrect spacing,

positioning and alignment can make the riving

knife ineffective in preventing kickback.

c. Always use the riving knife except when

plunge cutting. Riving knife must be replaced

after plunge cutting. Riving knife causes

interference during plunge cutting and can

create kickback.

d. For the riving knife to work, it must be

engaged in the workpiece. The riving knife is

ineffective in preventing kickback during short

cuts.

e. Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing

rate of a guard.

Residual risks

The following risks are inherent to the use of

saws:

• Injuries caused by touching the rotating parts.

ENGLISH

Even with the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be

avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the

uncovered parts of the rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ﬁngers when opening

the guards.

- Health hazards caused by breathing dust

developed when sawing wood, especially

oak, beech and MDF.

Saw blades

• Do not use blades of larger or smaller

diameter than recommended. For the proper

blade rating refer to the technical data. Use

only the blades speciﬁed in this manual,

complying with EN 847-1.

• Warning! Never use abrasive wheels.

Safety of others

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

Vibration

The declared vibration emission values stated in

the technical data and the declaration of

conformity have been measured in accordance

with a standard test method provided by EN

60745 and may be used for comparing one tool

with another. The declared vibration emission

value may also be used in a preliminary

assessment of exposure.

Warning! The vibration emission value during

actual use of the power tool can differ from the

declared value depending on the ways in which

the tool is used. The vibration level may increase

above the level stated.

When assessing vibration exposure to determine

safety measures required by 2002/44/EC to

protect persons regularly using power tools in

employment, an estimation of vibration exposure

should consider, the actual conditions of use and

the way the tool is used, including taking account

of all parts of the operating cycle such as the

times when the tool is switched off and when it is

running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury,

the user must read the instruction

manual.

Electrical safety

This tool is double insulated; therefore

no earth wire is required. Always check

that the power supply corresponds to

the voltage on the rating plate.

• If the supply cord is damaged, it must be

replaced by the manufacturer or an

authorised Black & Decker Service Centre in

order to avoid a hazard.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Spindle lock button

ENGLISH

6. Shoe

7. Saw blade

8. Saw blade guard

9. Riving knife

10. Saw dust outlet

Assembly

Warning! Before attempting any of the following

operations, make sure that the tool is switched

off and unplugged and that the saw blade has

stopped.

Removing and ﬁtting a saw

blade (ﬁg. A)

Removing

•

Keep the spindle lock button (5) depressed

and rotate the blade until the spindle lock

engages.

• Loosen and remove the blade retaining

screw (11) by turning it counterclockwise

using the spanner (12) supplied.

• Remove the outer washer (13).

• Remove the saw blade (7).

Fitting

•

Place the saw blade onto the inner ﬂange

(14), making sure that the arrow on the blade

points in the same direction as the arrow on

the tool.

• Fit the outer washer (13) on the spindle, with

the raised part pointing away from the saw

blade.

• Insert the blade retaining screw (11) into the

hole.

• Keep the spindle lock button (5) depressed.

• Securely tighten the blade retaining screw by

turning it clockwise using the spanner (12)

supplied.

• Adjust the riving knife as described below.

Adjusting the riving knife (ﬁg. B)

The riving knife prevents the saw blade from

jamming during rip sawing operations. The riving

knife must be adjusted after replacing the saw

blade.

• Loosen the screws (15), using the spanner

(12), while holding the riving knife in position.

• Position the riving knife (9) as shown.

• The distance between the toothed rim and the

riving knife should be 2 - 3 mm.

• The height difference between the toothed

rim and the lower end of the riving knife

should be 2 - 3 mm.

• Tighten the screws.

Fitting and removing the parallel

fence (ﬁg. C)

• The parallel fence is used to saw in a straight

line parellel to the edge of the workpiece.

Fitting

•

Loosen the locking knob (16).

• Insert the parallel fence (17) through the

openings (18).

• Slide the parallel fence into the desired

position.

• Tighten the locking knob.

Removing

•

Loosen the locking knob.

• Pull the parallel fence off the tool.

ENGLISH

Use

Warning! Let the tool work at its own pace. Do

not overload.

This tool can be used in the right hand or the left

hand.

Adjusting the sawing angle

(ﬁg. D)

The default angle between the saw blade and

the shoe is 90°.

• Use a square to check that the angle

between the saw blade and the shoe is 90°.

If the angle does not measure 90° adjust as

follows:

• Loosen the locking knob (19) to unlock the

saw shoe.

• Loosen the locknut (20) on the adjusting

screw (21).

• Screw the adjusting screw in or out to

achieve a 90° angle.

• Retighten the locknut.

• Tighten the locking knob to lock the saw

shoe in place.

Adjusting the depth of cut

(ﬁg. E)

The depth of cut should be set according to the

thickness of the workpiece. It should exceed the

thickness by approx. 2 mm.

• Loosen the knob (22) to unlock the saw

shoe.

• Move the saw shoe (6) into the desired

position. The corresponding depth of cut can

be read from the scale (23).

• Tighten the knob to lock the saw shoe in

place.

Adjusting the bevel angle (ﬁg. F)

This tool can be set to bevel angles between 0°

and 45°.

• Loosen the locking knob (19) to unlock the

saw shoe.

• Move the saw shoe (8) into the desired

position. The corresponding bevel angle can

be read from the scale (24).

• Tighten the locking knob to lock the saw shoe

in place.

Switching on and off

• To switch the tool on, move the lock-off button

(2) into the unlock position and squeeze the

on/off switch (1).

• To switch the tool off, release the on/off

switch.

Sawing

Always hold the tool with both hands.

• Let the blade run freely for a few seconds

before starting the cut.

• Apply only a gentle pressure to the tool while

performing the cut.

• Work with the shoe pressed against the

workpiece.

Hints for optimum use

• As some splintering along the line of cut on

the top side of the workpiece cannot be

avoided, cut on the side where splintering is

acceptable.

• Where splintering is to be minimised, e.g.

when cutting laminates, clamp a piece of

plywood onto the top of the workpiece.

ENGLISH

Using the sight guide (ﬁg. G)

The tool is equipped with a sight guide for

straight cutting (25) and for 45° bevel cutting

(26).

• Adjust the sight guide as described below.

• Align the left edge of the guides (25) or (26)

with the cutting line (27).

• Keep the sight guide aligned with the cutting

line while sawing.

• Work with the shoe pressed against the

workpiece.

Adjusting the sight guide

• Make a test cut halfway through a piece of

scrap wood.

• Withdraw the saw so the cutting line (27)

becomes visible.

• While keeping the saw in this position,

loosen the sight guide on the saw shoe as

shown.

• Align the 0° mark (25) on the sight guide with

the cutting line (27). When adjusting for 45°

bevel cuts, align the 45° mark (26) on the

sight guide with the cutting line.

• Secure the sight guide using the screw (28).

Dust extraction (ﬁg. H)

An adaptor is required to connect a vacuum

cleaner or dust extractor to the tool.

• Insert the dust extraction adaptor (29) into

the saw dust outlet (10).

• Connect the vacuum cleaner hose (30) to the

adaptor.

Maintenance

Your Black & Decker corded/cordless

appliance/tool has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper tool care and regular

cleaning.

Warning! Before performing any maintenance

on corded/cordless power tools:

• Switch off and unplug the appliance/tool.

• Or switch off and remove the battery from the

appliance/tool if the appliance/tool has a

separate battery pack.

• Or run the battery down completely if it is

integral and then switch off.

• Unplug the charger before cleaning it. Your

charger does not require any maintenance

apart from regular cleaning.

• Regularly clean the ventilation slots in your

appliance/tool/charger using a soft brush or

dry cloth.

• Regularly clean the motor housing using a

damp cloth. Do not use any abrasive or

solvent-based cleaner.

• Regularly open the chuck and tap it to

remove any dust from the interior (when

ﬁtted).

Mains Plug Replacement

If a new mains plug needs to be ﬁtted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal of

the new plug.

• Connect the blue lead to the neutral terminal.

• If the product is class l (earthed), connect the

green / yellow lead to the earth terminal.

ENGLISH

Warning! If your product is class ll double

insulated (only 2 wires in the cord set), no

connection is to be made to the earth terminal.

Follow the ﬁtting instructions supplied with good

quality plugs.

Any replacement fuse must be of the same

rating as the original fuse supplied with the

product.

Technical Data

KS1300 KS1301

TYPE 1 TYPE 1

Input voltage VAC 220-240 220-240

Power input W 1,300 1,300

No-load speed min

-1

5,000 5,000

Max. depth of cut mm 65 65

Depth of cut at 45°

bevel mm 50 50

Blade diameter mm 190 190

Blade bore mm 16 16

Blade tip width mm 2.3 2.3

Weight kg 5 5

ENGLISH

Protecting the environment

Separate collection. This product must not

be disposed of with normal household

waste.

Should you ﬁnd one day that your Black &

Decker product needs replacement, or if it is of

no further use to you, do not dispose of it with

other household waste. Make this product

available for separate collection.

• Black & Decker provides a facility for

recycling Black & Decker products once they

have reached the end of their working life.

This service is provided free of charge. To

take advantage of this service please return

your product to any authorised repair agent

who will collect them on our behalf.

• You can check the location of your nearest

authorised repair agent by contacting your

local Black & Decker ofﬁce at the address

indicated in this manual. Alternatively, a list of

authorized Black & Decker repair agents and

full details of our after-sales service and

contact are available on the Internet at:

www.2helpU.com.

Warranty

If a Black & Decker product becomes defective

due to a material or manufacturing defect , within

12 months from the date of purchase, Black &

Decker guarantees to replace defective parts or

replace such products to ensure minimum

inconvenience to the customer unless:

• The product has been subjected to misuse or

neglect.

• The product has sustained damage through

foreign objects, substances or accidents.

• Repairs have been attempted by persons

other than authorised repair agents or Black

& Decker service staff.

To claim on the warranty, you will need to submit

proof of purchase to the seller or an authorised

repair agent. You can check the location of your

nearest authorised repair agent by contacting

your local Black & Decker ofﬁce at the address

indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full

details of our after-sales service and contacts are

available on the Internet at: www.2helpU.com.

Please visit our website www.blackanddecker.ae

to register your new Black & Decker product and

to be kept up to date on new products and

special offers. Further information on the Black &

Decker brand and our range of products is

available at www.blackanddecker.ae.

ARABIC

30 29 10

25 27 28

ARABIC

ΩGóîà°S’G ¢VôZ

äÉéàæeh Ö°ûÿG öûæd ôµjO ófBG ∑ÓH QÉ°ûæe º«ª°üJ ”

á£°SGƒH ¬eGóîà°S’ ºª°üe RÉ¡÷G Gòg ¿CÉH

Éª∏Y ,ÜÉ°ûNC’G

.§≤a ∂∏¡à°ùŸG

áeÓ°ùdG äGOÉ°TQEG

äGOÉ°TQEGh äGôjò– áaÉc IAGôb »¨Ñæj !ôjò–

äGôjòëàdG áaÉc ´ÉÑJEG ΩóY ÖÑ°ùàj ó≤a .áeÓ°ùdG

áeó°U çhóM ‘ √ÉfOCG IQƒcòŸG äGOÉ°TQE’Gh

AÉ«°TC’G √òg ™«ªL hCG IÒ£N áHÉ°UEG hCG ≥jôM hCG á«FÉHô¡c

É©e

´ƒLô∏d äGOÉ°TQE’Gh äGôjòëàdG áaÉµH ®ÉØàM’G ≈Lôj

ÓÑ≤à°ùe É¡«dEG

áaÉc ‘ OQGƒdG "»FÉHô¡c RÉ¡L" í∏£°üŸG Ò°ûj

…òdG »FÉHô¡µdG RÉ¡÷G ¤EG √ÉfOCG IQƒcòŸG äGôjòëàdG

»FÉHô¡µdG RÉ¡÷G hCG (É

.(É

ΩÉcôdÉH á¶àµŸG hCG áª∏¶ŸG ≥WÉæŸG ÖÑ°ùàJ PEG ,G

ó«L

.çOGƒ◊G ´ƒbh ‘

á∏HÉb AGƒLCG ‘ á«FÉHô¡µdG Iõ¡LC’G π«¨°ûàH º≤J ’ .Ü

hCG äGRÉZ hCG πFGƒ°S OƒLh ‘ É¡∏«¨°ûJ πãe ;QÉéØfÓd

á«FÉHô¡µdG Iõ¡LC’G ¿C’

.áæNOC’G

Iô£«°ù∏d ∂fGó≤a ‘ AÉ¡dE’G ÖÑ°ùàj ó≤a ,»FÉHô¡µdG

.RÉ¡÷G ≈∏Y

á«FÉHô¡µdG áeÓ°ùdG .2

™e á≤aGƒàe »FÉHô¡µdG RÉ¡÷G ¢ùHGƒb ¿ƒµJ ¿CG Öéj .CG

≤∏£e ÖæŒ .»FÉHô¡µdG QÉ«àdG òNCÉe

™e ä’ƒﬁ ¢ùHGƒb ájCG Ωóîà°ùJ ’h ,á≤jôW ájCÉH

π«∏≤J ¤EG …ODƒj á≤aGƒàŸG »FÉHô¡µdG QÉ«àdG òNBÉeh

Ö«HÉfC’G πãe á°VQDƒŸG í£°SCÓd ∂ª°ùL á°ùeÓe ÖæŒ .Ü

OGOõJ å«M ,äÉLÓãdGh óbGƒŸGh áÄaóàdG Iõ¡L

CGh

∂ª°ùL ¿Éc GPEG á«FÉHô¡c áeó°üH ∂àHÉ°UEG ôWÉﬂ

.É

°VQDƒe

¤EG »FÉHô¡µdG RÉ¡÷G πNGO AÉŸG ∫ƒNO …ODƒj ±ƒ°ùa

.á«FÉHô¡c áeó°üH áHÉ°UE’G ôWÉﬂ IOÉjR

.ÅWÉN πµ°ûH »FÉHô¡µdG QÉ«àdG ∂∏°S ΩGóîà°SG ΩóY Öéj .O

RÉ¡÷G πª◊ »FÉHô¡µdG QÉ«àdG ∂∏°S É

≤∏£e Ωóîà°ùJ ’

Éªc .»FÉHô¡µdG QÉ«àdG øY ¬∏°üa hCG ¬Ñë°S hCG »FÉHô¡µdG

IQGô◊G øY

Éª∏Y .ácôëàŸG AGõLC’G hCG IOÉ◊G ±Gƒ◊G hCG âjõdG hCG

ôWÉﬂ øe ójõJ áµHÉ°ûàŸG hCG áØdÉàdG ∑Ó°SC’G ¿CÉH

.á«FÉHô¡c áeó°üH áHÉ°UE’G

Öéj ,êQÉÿG ‘ »FÉHô¡µdG RÉ¡÷G π«¨°ûJ óæY .`g

,»LQÉÿG ΩGóîà°SÓd Ö°SÉæŸG π«°UƒàdG ∂∏°S ΩGóîà°SG

Ö°SÉæŸG »FÉHô¡µdG QÉ«àdG ∂∏°S ΩGóîà°SG ¿C’

Gô¶f

.á«FÉHô¡c

Öéj ,ÖWQ ¿Éµe ‘ »FÉHô¡µdG RÉ¡÷G π«¨°ûJ ºà– GPEG .h

¿C’

Gô¶f ,»≤ÑàŸG QÉ«àdG øe ájÉbh RÉ¡L ΩGóîà°SG

øe π∏≤j »≤ÑàŸG QÉ«àdG øe ájÉbh RÉ¡L ΩGóîà°SG

.á«FÉHô¡c áeó°üH áHÉ°UE’G ôWÉﬂ

á«°üî°ûdG áeÓ°ùdG .3

GQòM øc .CG

»FÉHô¡µdG RÉ¡÷G Ωóîà°ùJ ’ .»FÉHô¡µdG RÉ¡÷G π«¨°ûJ

µ¡æe âæc GPEG

AÉæKCG á∏Ø¨dG øe á¶◊ ÖÑ°ùàJ ó≤a ,ájhOC’G hCG á«dƒëµdG

á«°üî°T áHÉ°UEG çhóM ‘ á«FÉHô¡µdG Iõ¡LC’G π«¨°ûJ

.á¨dÉH

¥Gh É

äÉHÉ°UEG çhóM ôWÉﬂ øe π∏≤j ,™ª°ùdG ájÉbh äGhOCGh

.á«°üî°T

¿hO ∫ƒë∏d áeRÓdG äÉWÉ«àM’G áaÉc PÉîJG Öéj .ê

óY ™°Vh ‘ ìÉàØŸG ¿CG ócCÉJ .ó°üb ¿hO RÉ¡÷G π«¨°ûJ

hCG/h »FÉHô¡µdG QÉ«àdG Qó°üÃ π«°UƒàdG πÑb π«¨°ûàdG

πªM ¿

CG PEG .¬∏ªM hCG RÉ¡÷G ™aQ hCG ,äÉjQÉ£ÑdG Ö«côJ

hCG ìÉàØª∏d á°ùeÓe ™HÉ°UC’Gh á«FÉHô¡µdG Iõ¡LC’G

™°Vh ‘ ìÉàØŸGh ábÉ£dÉH á«FÉHô¡µdG Iõ¡LC’G ójhõJ

.çOGƒM ´ƒbh ¤EG …ODƒj π«¨°ûàdG

ARABIC

áHÉ°UEG çhóM ‘ »FÉHô¡µdG RÉ¡÷G øe QGhódG Aõ÷ÉH

.á«°üî°T

Öéj Éªc ,•ôØe πµ°ûH RÉ¡÷G øe ÜGÎb’G ΩóY Öéj .`g

RÉ¡÷G ≈∏Y ó«L πµ°ûH Iô£«°ùdG ∂d í«àj ∂dP

¢ùHÓŸG AGóJQG ΩóYh ,áÑ°SÉæŸG ¢ùHÓŸG AGóJQG Öéj .h

¢ùHÓŸG ¿C’ ,ácôëàŸG AGõLC’G øY G

ó«©H ∂jRÉØbh

.ácôëàŸG AGõLC’G

hCG QÉÑ¨dG êGôîà°S’ äGhOCÉH

GOhõe RÉ¡÷G ¿Éc GPEG .R

QÉÑ¨dG ™«ªŒ äGhOCG ΩGóîà°SG ¿CG Éªc .Ö°SÉæe πµ°ûH

.QÉÑ¨dÉH á£ÑJôŸG ôWÉîŸG øe π∏≤j

ÒZ ¢VôZ ‘ »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ΩóY Öéj .CG

»FÉHô¡µdG RÉ¡÷G Ωóîà°SG Öéj πH ,¬d ¢ü°üﬂ

»FÉHô¡µdG RÉ¡÷G ¿C’ ,√ójôJ …òdG ¢Vô¨dÉH ¢UÉÿG

‘ ºµëàdG ™£à°ùJ ⁄

GPEG »FÉHô¡µdG RÉ¡÷G Ωóîà°ùJ ’ Ü

…CG ¿C’ ,ìÉàØŸG á£°SGƒH ¬∏«¨°ûJ ±É≤jEGh ¬∏«¨°ûJ

ìÉàØŸG ΩGóîà°SÉH ¬«a ºµëàdG øµÁ ’ »FÉHô¡c RÉ¡L

.¬MÓ°UEG Öéjh ôWÉîŸÉH

ÉaƒØﬁ ¿ƒµj

QÉ«àdG Qó°üe øY »FÉHô¡µdG RÉ¡÷G ¢ùHÉb π°üa Öéj .ê

Iõ¡LC’G ‘ äÉ≤ë∏e ájCG Ö«côJ hCG äGÒ«¨J

á«FÉbƒdG áeÓ°ùdG äGAGôLEG ¿C’ ,É¡æjõîJ hCG á«FÉHô¡µdG

»FÉHô¡µdG RÉ¡÷G π«¨°ûJ AóH ôWÉﬂ øe π∏≤J √òg

.ó°üb ¿hO ICÉéa

ÒZ ¢UÉî°TCÓd íª°ùJ ’h ∫ÉØWC’G ∫hÉæàe øY

ÉeóæY

Gô£N πµ°ûJ á«FÉHô¡µdG Iõ¡LC’Éa ,»FÉHô¡µdG

.ÚHQóe ÒZ ¢UÉî°TCG É¡eóîà°ùj

¢üëaG .á«FÉHô¡µdG Iõ¡LCÓd ájQhO áfÉ«°U AGôLEG Öéj .`g

AGõLC’G øe √ƒ∏N øe ócCÉàdGh ácôëàŸG AGõLC’G ácôM

.¬∏«¨°ûJ IAÉØc ≈∏Y ôKDƒj ób ôNBG A»°T …CG øeh IQƒ°ùµŸG

RÉ¡÷G ìÓ°UEG Öéj ,∞∏J …CG ±É°ûàcG ” GPEGh

Éª∏Y ,¬eGóîà°SG πÑb »FÉHô¡µdG

.á«FÉHô¡µdG Iõ¡LC’G áfÉ«°U Aƒ°S ÖÑ°ùH ™≤J

¿C’ ,áØ«¶fh

IOÉM ™£≤dG äGhOCG ≈∏Y ®ÉØ◊G »¨Ñæj .h

Ö°SÉæŸG πµ°ûdÉH É¡«∏Y ®ÉØ◊G ºàj »àdG ™£≤dG äGhOCG

.ºµëàdG ‘ π¡°SCGh

¬FGõLCGh ¬JÉ≤ë∏eh »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG Öéj .R

±hôX òNCG ™e ,äGOÉ°TQE’G √ò¡d É

≤ah ∂dP ¤EG Éeh

äÉ«∏ªY πLCG øe »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ÖÑ°ùàj

çhóM ‘ É¡∏LCG øe ºª°üŸG ¢VGôZC’G iƒ°S π«¨°ûJ

.ôWÉﬂ

áfÉ«°üdG .5

á£°SGƒH »FÉHô¡µdG RÉ¡÷G ìÓ°UEGh áfÉ«°U Öéj .CG

∂dP ¿C’ ,á≤HÉ£e QÉ«Z ™£b ΩGóîà°SÉH πgDƒe ¢üî°T

.»FÉHô¡µdG RÉ¡÷G áeÓ°S øª°†j

RÉ¡÷G ¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò–

»FÉHô¡µdG

¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò– !ôjò–

.Ò°TÉæŸG ´GƒfCG ™«ªL

hCG ,QÉ°ûæª∏d ‘É°VE’G ¢†Ñ≤ŸG ≈∏Y iôNC’G ∑ój

Éà∏µH QÉ°ûæŸG ∑É°ùeEG ádÉM ‘ ¬fC’ ,∑ôëŸG ¥hóæ°U

ARABIC

¬fCÉH

óY .ê

πØ°SCG IôØ°ûdG ø°S øe øµ‡ AõL πbCG ô¡¶j ¿CG Öéj

.πª©dG á©£b

Ωƒ≤J á©£b …CG

É≤∏£e ∂bÉ°S ≈∏Y hCG ∂jój ‘ πª– ’ .O

äGP ∑É°ùeEG äGhOCG á£°SGƒH »FÉHô¡µdG RÉ¡÷G ∂°ùeG .`g

¬«a …öùj ∂∏°S ™£b …ODƒj óbh ,¬H ¢UÉÿG »FÉHô¡µdG

.á«FÉHô¡c áeó°üd Ωóîà°ùŸG

¬«LƒJ π«dO hCG öûf õLÉM

ÉehO Ωóîà°SG ,öûædG óæY .h

¢Uôa øe π∏≤jh ™£≤dG ábO øe ójõj ∂dP ¿C’ ,º«≤à°ùe

.IôØ°ûdG πbô©J

ÉeEG) ∫Éµ°TC’Gh ΩÉéMC’G äGP äGôØ°ûdG

ÉehO Ωóîà°SG .R

¿C’ ,áÑ°SÉæŸG ´hò÷G äÉëàah (ájôFGódG hCG á«ªéædG

ób QÉ°ûæŸG ‘ Ö«cÎdG ™£b ºFÓJ ’ »àdG äGôØ°ûdG

.ºµëàdG ¿Gó≤a ¤EG …ODƒJh …ôFGO ÒZ πµ°ûH QhóJ

áØdÉJ äGôØ°T ÒeÉ°ùe hCG äÉµ∏a …CG

É≤∏£e Ωóîà°ùJ ’ .ì

ÒeÉ°ùe hCG äÉµ∏a ΩGóîà°SG Öéj πH ,áÑ°SÉæe ÒZ hCG

…òdG QÉ°ûæŸG ´ƒæd

É°ü«°üN áªª°üŸG äGôØ°ûdG

äÉLQO ≈°übCGh πãeC’G AGOC’G ≈∏Y ∫ƒ°üë∏d ¬eóîà°ùJ

.π«¨°ûàdG óæY ¿ÉeC’G

™«ªL ¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGOÉ°TQEG

Ò°TÉæŸG ´GƒfCG

•

√ÉŒÉH ¬YÉaófGh QÉ°ûæŸG ≈∏Y Iô£«°ùdG ¿Gó≤a

.Ωóîà°ùŸG

•

.Ωóîà°ùŸG ƒëf áYöùH

,≥°ûdG ‘ ÅWÉN √ÉŒG ‘ äQÉ°S hCG IôØ°ûdG äƒàdG GPEGh

•

øe »Ø∏ÿG ±ô£dG ‘ IOƒLƒŸG ¿Éæ°SC’G Ωƒ≤J ó≤a

√ÉŒÉH ÉgõØbh öûædG ≥°T øe IôØ°ûdG OGóJQG ‘

.Ωóîà°ùŸG

áª«∏°ùdG π«¨°ûàdG äGOÉ°TQEG hCG äGAGôLEG ´ÉÑJG ΩóY hCG/h

ƒg Éªc áÑ°SÉæŸG äÉWÉ«àM’G PÉîJÉH É¡ÑæŒ øµÁh

.√ÉfOCG í°Vƒe

ÚYGQòdG AÉ≤HEGh Iƒ≤H øjó«dG Éà∏µH QÉ°ûæŸG ∑É°ùeEG Öéj .CG

¢ù«dh IôØ°ûdG »ÑfÉL ióMEG ≈∏Y ±ƒbƒdG Öéj

É¡«∏Y Iô£«°ùdG Ωóîà°ùª∏d øµÁ ¬fCG ’EG ,∞∏î∏d QÉ°ûæŸG

.áÑ°SÉæŸG äÉWÉ«àM’G äòîJG Ée GPEG

‘ ácôM ÓH QÉ°ûæŸG ≈∏Y ≥HGh π«¨°ûàdG QR ∑ôJG ,¿Éc

’ .

É≤∏£e ∫hÉ–

.áØ«æY äGOGóJQG çó– ób ’EGh ,IôØ°ûdG ¿GQhO AÉæKCG

ÒZ QÉ°ûæŸG ¿Éæ°SCG ¿CG ócCÉJh ≥°ûdG ∞°üàæe ‘ QÉ°ûæŸG

.ìƒ∏dG áaÉM øe Üô≤dÉHh

La page charge ...

Black & Decker Powerful Solutions KS1301 Manuel utilisateur

Marque: Black & Decker

Modèle: Powerful Solutions KS1301

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Black & Decker Powerful Solutions KS1301 User manual

Black & Decker Powerful Solutions KS1301 Manuel utilisateur

Ce manuel convient également à

Black & Decker Powerful Solutions KS1301 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents