CMP DEL OZONE 25 Generator Le manuel du propriétaire

4-2162-01 Rev.J

ENGLISH ..............................1

CANADIEN FRANÇAIS ....15

ESPAÑOL ...........................31

®

DEL OZONE® 25/50/100

INSTALLATION INSTRUCTIONS & PRODUCT MANUAL

C-M-P.COM/DEL

®

IMPORTANT INFORMATION

READ AND FOLLOW ALL INSTRUCTIONS

• Read this manual completely before attempting installation. Failure to install in accordance

with the installation instructions could void warranty and result in injury or death.

• All permanent electrical connections should be made by a qualified electrician.

• A pressure wire connector, labeled “bonding lug”, is provided on the outside of the unit to

permit connection to a minimum No. 6 AWG (13.3 mm2) solid bonding conductor between

this point and any metal equipment, metal enclosures of electrical equipment, metal water

pipes, or conduit within 5 feet (1.5 meters) of the unit as needed to comply with local

requirements.

• If the DEL Ozone generator electrical connection is to be attached to the pool controls, be

sure the pool controls are protected by a Ground Fault Circuit Interrupter (G.F.C.I.). If the DEL

Ozone generator is connected to an independent electrical supply, then a G.F.C.I. must be

installed between the DEL Ozone generator and the electrical supply.

• Install at least 5 feet (1.5 meters) from wall of pool using nonmetallic tubing. Tubing is

supplied with the DEL Ozone generator. Never replace this tubing with metal tubing. Install

ozone generator no less than one (1) foot above maximum water level to prevent water from

contacting electrical equipment. Install in accordance with the installation instructions.

• Follow all applicable electrical codes.

• DANGER ELECTRIC SHOCK HAZARD: Be sure to turn power OFF and disconnect

from power source before any service work is performed. Failure to do so could result in

serious injury or death.

• The DEL Ozone® must be installed in an outdoor location, or indoors in a forced air

ventilated room, and installed so that the orientation is exactly as shown in Figure 1. Install

to provide water drainage of generator to protect electrical components.

• Mount the DEL Ozone® generator so that it is inaccessible to anyone in the pool. Never

attempt any servicing while unit is wet.

• WARNING Short-term inhalation of high concentrations of ozone and long term

inhalation of low concentrations of ozone can cause serious harmful physiological effects.

DO NOT inhale ozone gas produced by this device.

• DANGER For your safety, do not store or use gasoline, chemicals or other flammable

liquids or vapors near this or any other appliance.

• WARNING To reduce the risk of injury, do not permit children to use this product,

unless they are closely supervised at all times.

• WARNING If unit is not operated according to instructions, high dosages of harmful

substances may potentially be released.

• ENVIRONMENTAL NOTICE - Hg-Lamp CONTAINS MERCURY. Manage in accordance with

disposal laws. See: www.lamprecycle.org.

SAVE THESE INSTRUCTIONS!

1 Overview

1A. Description .......................................................................................................1

1B. Specications ..................................................................................................1

2 Installation

2A. Location ............................................................................................................1

2B. Wall Mounting ...............................................................................................2

2C. Plumbing .........................................................................................................3

2D. Electrical ...........................................................................................................6

3 Operation

3A. General .............................................................................................................7

3B. Initial System Start-Up .................................................................................7

3C. Normal Operation ........................................................................................7

3D. System Shut-Down ....................................................................................... 7

3E. Water Chemistry ........................................................................................... 7

4 Maintenance & Service

4A. System Electromechanical Overview ......................................................8

4B. System Maintenance ....................................................................................8

4C. Generator Servicing .....................................................................................9

4D. Contact Informartion ................................................................................. 10

4E. Ordering Information ................................................................................ 10

4F. Replacement Parts ...................................................................................... 10

5 Troubleshooting .................................................................................................11

Appendix A: Installation Plumbing ................................................................ 13

TABLE OF CONTENTS

ENGLISH

1

1A. Description

The DEL Ozone generators described in this manual are designed to

provide the benefits of ozonated water in an environmentally safe and

effective manner. The high quality, specially engineered components ensure

efficient ozone output and reliable performance.

As a result of proper use of the DEL Ozone generators, unpleasant effects of

traditional chemical use are virtually eliminated. The DEL Ozone generators

are safe and harmless to your equipment when installed properly.

1B. Specifications

Power Requirements:

Ozone 25 ..............................................................................120/240V, 0.10A, 50/60Hz

Ozone 50 .............................................................................120/240V, 0.24A, 50/60Hz

Ozone 100 ............................................................................. 120/240V, 0.31A, 50/60Hz

Location Requirements:

Mounting: Wall mount in a clean, protected area.

Ambient Temp.: 35°F - 120°F (2°C - 49°C)

2A. Location

The DEL Ozone units are designed for wall mounting. Mount generator in

a clean, protected area, either indoors or outdoors (preferably out of direct

sunlight). Locate generator out of reach of sprinklers or drainage spouts.

Allow sufficient access for maintenance, all tubing, and electrical wires.

Ozone generator should be installed at least (not less than) one foot above

the maximum water level.

1 OVERVIEW

ENGLISH

2

Ozone 100 Ozone 25 & 50

5.77”

3 x .25”

19.60”

2.68”

5.77”

Second

Cell Ozone

50 Only

2.68”

3 x .25”

12.40”

2B. Wall Mounting

1. Open the enclosure door and locate the three mounting holes on the

back wall of the enclosure. There will be two holes located near the top

on the left and right and one located in the center near the bottom.

Refer to Figure 1 for clarification.

2. Install screws (or other hardware appropriate for the mounting surface)

through the two mounting holes near the top of the enclosure. Install

the last screw through the mounting hole near the bottom of the

enclosure. Mounting hardware must be driven until the head fully

contacts the enclosure wall. Mounting hardware head must not be

smaller than 0.25 inches (6.3 mm) in diameter and the threads of the

hardware must be smaller than 0.25 inches (6.3 mm) in diameter.

2C. Plumbing

2 INSTALLATION

Figure 1: Mounting Hole Dimensions

ENGLISH

3

2 INSTALLATION

Figure 2: Injector Manifold Mounting Location

Chlorine

Feeder

Pump

from Pool Return

Filter Heater

Injector Manifold

DEL Ozone

Generator

Check

Valve OZONE

INJECTED

Ozone gas is introduced to the pool circulation line using a venturi injector.

Suction developed by the venturi allows the DEL Ozone generator to

operate safely under vacuum.

Note: Water must not travel back to the ozone generator. Mounting the

unit above the water line and scheduled check valve replacement will keep

water from entering the DEL Ozone generator.

2C-1. Plumbing the Injector Manifold

The injector manifold must be installed in the pool’s main return line after

all other pool equipment (pump, filter, heater, and cleaner). Figure 2 shows

the most basic installation. For installation with additional oxidizers and

pool cleaners, refer to Appendix A.

Note: The injector manifold should be installed above water level

whenever possible. If the injector manifold is installed below water level,

take proper precautions to prevent water from draining through the

injector and damaging the surrounding area. For example, use clamps

on all tube connections, run ozone tubing above water level and provide

adequate drainage around the pool equipment.

Locate an appropriate section of the return line and install the injector

ENGLISH

4

manifold with PVC cement. Be very careful to observe and follow the

correct water flow direction (as indicated by the arrow on the injector

manifold).

2C-2. Water Line Check Valve

If the pool equipment is mounted above the water line, a check valve must

be installed between the pump outlet and the injector manifold. This will

prevent the pump from draining and losing its prime (when not in use).

CMP HydroSeal™ check valve recommended.

2C-3. Pressure Test

If a pressure test is required, it should be performed prior to connecting the

ozone gas line. Install the 3/4” pipe cap provided onto the injector for the

pressure test.

Figure 3a: Flow Meter Assembly

Add an arrow that points to the join of the

green ozone tube to the assembly, and

entitle it "Flow Meter Assembly:

Flow Meter

Assembly

Injector

Assembly

Tube

Adaptor

2 INSTALLATION

ENGLISH

5

2 INSTALLATION

2C-4. Flow Test - Refer to Figure 3a.

1. Install tube adapter on injector. Use Teflon thread tape as needed.

2. Connect the flow meter assembly to the tube adapter.

3. Hold the flow meter assembly so that the clear plastic chamber is

vertical with the tubing on top.

4. Turn on the pool’s circulation system as this allows the injector assembly

to pull a vacuum. Under normal operation, the ball in the flow meter

assembly will be floating in between its Max and Min line. Under worst-

case system conditions the flowmeter ball should indicate at least a

small amount of air flow. Flow may be adjusted as described below.

Manually Adjustable Injector Manifold: Gas flow can be controlled by

adjusting the valve on the manifold. Close the valve to increase gas flow,

open the valve to decrease gas flow.

Self-Adjusting Injector Manifold: This manifold is equipped with a

spring loaded valve. It cannot be manually adjusted, but provides a wide

operating range. If more gas flow is necessary, verify that other valves in

the system are not inhibiting flow through the manifold. If you experience

complications see TROUBLESHOOTING.

Add down arrow here with

the supporting text "Flow of

Check Valve"

Add arrow pointing to

the green square

between the ozone

tubes that says "Check

Valve Assembly"

Check Valve

Flow of

Check Valve

Figure 3b: Ozone Tube Assembly

Ozone Tube

ENGLISH

6

2 INSTALLATION

2C-5. Ozone Tube Connection - Refer to Figure 3b.

After the system has been set for the correct flow rate, remove the flow

meter assembly and connect the ozone tube between the ozone outlet

barb on the DEL Ozone generator, and the tube adapter on the injector

assembly. Ensure that the check valve arrow is pointing toward the injector.

If equipment is above water level, cut off the excess tubing so that the line

from the injector to the DEL Ozone generator is as straight and free from

dips and loops as possible. If equipment is below the water level, run tubing

to a point above water level. Ensure that all tube connections are secured

with clamps.

2D. Electrical

2D-1. Main Power

This device is intended to be installed by a certified electrical technician, in

accordance with local electrical codes. Connect the DEL Ozone generator

to the pool timing clock so that the DEL Ozone generator operates

simultaneously with the pool pump. The DEL Ozone generator has three

available knockouts for a 1/2 inch conduit fitting, two on each side and

one on the back. Remove only the ideal knockout and install the proper

conduit fitting. Open the enclosure and locate the terminal block. Connect

Line 1, Line 2, and ground to the terminal block as indicated by the label

on the inside of the enclosure door. Refer to the IMPORTANT SAFETY

INSTRUCTIONS at the beginning of this manual for important wiring

information.

2D-2. Earth Grounding Lug

Using an 6 AWG (13.3 mm2) conductor, connect the grounding lug on the

bottom of the DEL Ozone generator to an appropriate earth contact.

3A. General

ENGLISH

7

To achieve optimal performance from the ozone system, the pool must be

as clean as possible to start with.

1. Backwash or clean filters one day before starting the ozone generator.

2. Superchlorinate pool water using a chlorine based shock treatment prior

to ozone system start-up.

3. Test pool chemistry and adjust pH between 7.4 and 7.6. Adjust total

alkalinity between 80 and 120 ppm.

4. Run pool filtration continuously for 24 hours prior to starting ozone

system.

3B. Initial System Start-Up

Upon completing all of the generator system connections and cleaning the

pool as outlined above, you are ready to start the ozone generator.

1. Check electrical connections.

2. Check for proper voltage.

3. Turn on pool circulation system.

3C. Normal Operation

Indicator Lights: When the pool’s circulation system starts, the DEL Ozone

generator will power up and the green indicator lights on the ozone cells

will illuminate. Open the enclosure door to verify that all indicator lights are

green.

3D. System Shut-Down

The following sequence of steps must be followed for servicing or for storage.

1. Disconnect the power to the ozone generator.

2. After the generator has been shut down, the pool water circulation

pump may be turned off.

3. If the system is to be shut down for an extended period, disconnect the

ozone tube from the unit.

3E. Water Chemistry

Regular chlorine or bromine testing should be performed as normal. Ozone

will be eliminating the majority of contaminants. Therefore, only a small

amount of chemicals will need to be added - just enough to maintain an

appropriate residual level of chlorine or bromine. Ozone is pH neutral thus

minimizing pH adjustments.

4A. System Electromechanical Overview- Ozone Module

3 OPERATION

ENGLISH

8

4 MAINTENANCE & SERVICE

The DEL Ozone generators are constructed with high voltage plasma gap

ozone modules. Each module has an indicator light that signals it’s working

properly. If the light goes out, replace the module.

4B. System Maintenance

4B-1. The green indicator lights on the ozone modules located inside the

enclosure indicate that the power supplies are operating properly. When

an indicator light goes out, replace the corresponding ozone module.

Regularly check inside the unit to verify all the ozone modules are working.

4B-2. Each ozone module should be replaced after 15,000 hours of

operation. Even if the green indicator light(s) are glowing, the ozone

module may be producing less ozone after this period of time due to

contamination within the plasma gap ozone chamber.

4B-3. Regularly reinstall and check the flowmeter for proper flow. Always

remove the flow meter after confirming proper flow. Inspect ozone tube for

cracks or wear and replace as necessary.

4B-4. Replace the ozone tube every year or sooner, if needed. If there

is evidence of water leaking past the check valve toward the DEL Ozone

generator, shut down the unit immediately and replace the ozone tube

and check valve. If water entered the DEL Ozone generator, allow the unit

to dry completely before restarting. Evidence of water in the DEL Ozone

generator may void the warranty.

WARNING Trace amounts of nitric acid may be present in the ozone

gas line. Wear proper safety equipment (gloves and eye protection)

and avoid direct contact with any condensation in the line.

4B-5. While operating, check to see if bubbles are entering the pool.

If an MDV is installed, check the MDV for bubbles.

ENGLISH

9

4C. Generator Servicing

4C-1. Opening the Unit

The DEL Ozone generator may be serviced on the wall without

disconnecting any of the plumbing or wiring. Simply remove the two screws

on the right side of the enclosure door to open the unit.

4C-2. Ozone Module Replacement

When the green indicator lights go out on the ozone modules, the

corresponding ozone module will need to be replaced.

4 MAINTENANCE & SERVICE

Grounding

Lugs Ozone Outlet Barb

Terminal Block

Ozone Module

Connector

Figure 4: DEL Ozone Overview

(Ozone 100 Shown)

Ozone Outlet

Manifold

Ozone Module

Light

ENGLISH

10

4 MAINTENANCE & SERVICE

To replace an Ozone Module:

1. Disconnect the manifold or tubing from the ozone module.

Note: For the Ozone 25 and Ozone 50, pull the tubing clamp back from

the ozone module barb connector, then pull the tubing from the barb.

2. Locate the ozone module power connector and disconnect it from the

wire harness.

3. Remove the ozone module mounting screws. The ozone module can

now be removed from the unit.

4. Install the new ozone module by reversing the steps.

4D. Contact Information

For technical assistance:

• Call: 1 (800) 733-9060

• Email: suppor[email protected]

• Or visit our website: www.c-m-p.com

4E. Ordering Information

To locate a dealer nearest you call 1 (800) 733-9060

or visit www.c-m-p.com.

Be prepared with the following information:

• Name

• Date Purchased

• Address

• Dealer Name

• Model #

4F. Replacement Parts List:

Ozone Module Kit ............................................................................... 9-1636-01

Each ozone module should be replaced after 15,000 hours of use.

Ozone Tube Assembly .......................................................................9-0770-01

The Ozone Tube Assembly (includes Ozone Tube and Check Valve) must be replaced

once a year.

Ozone Module Filter ..........................................................................9-0858-01

Replace once a year.

Note: The warranty is void if the parts listed above are not replaced at

recommended intervals.

ENGLISH

11

5. Troubleshooting

Knowledge of electrical applications is required for trouble shooting.

Contact a certified electrician if you are unsure of your ability to service

the equipment. Improper servicing will void generator warranty. If any

condition persists contact CMP technical support (see section 4D)

Symptom: Module Indicator Lights not lit when pool system is on.

1. No power to the ozone generator from the power source:

a. Check circuit breaker at the power distribution box.

b. Check for loose connections or wiring breaks from the power

distribution box to the generator.

c. The fuse in the unit has blown and needs to be replaced. The

fuse is a replaceable glass, .25” x 1.25”, 1 amp, slo-blo type.

2. G.F.C.I. has tripped.

a. Check power cord and reset G.F.C.I.

Symptom: Flowmeter not indicating flow.

1. Injector not supplying adequate suction.

a. Check pump, filters, and skimmers to ensure water is flowing

through injector.

b. Ensure that there is no debris clogged inside the injector.

2. Tubing is impaired.

a. Check for kinks or clogs.

b. Check for cracks or cuts.

c. Check connections.

d. Check that the check valve is installed with the arrow pointing

towards the injector.

e. Be sure that the check valve has not become fouled with debris.

Disconnect the ozone tube from the injector. With the pump

running, cover the end of the injector with your thumb, and feel

for suction. If there is sufficient suction without the check valve,

replace the check valve with a new one.

Symptom: Ozone tube becomes yellow/brown and brittle.

5 TROUBLESHOOTING

ENGLISH

12

The high concentration of ozone created by the DEL Ozone family

of ozone generators, as well as environmental conditions like UV

sunlight will tend to deteriorate the supplied ozone tube. This is

normal and acceptable, as long as the tubing doesn’t become

cracked and leak. Because of this, the ozone tube and check valve

should be replaced every year.

Symptom: Can’t get ball to stay in the center of flowmeter.

The flowmeter provided is a general tool to setup flow to the

ozone generator. Flow will vary depending on pressures across the

injector, and therefore can be affected by things such as filter or

strainer loading. The ozone generator’s efficiency is optimized near

the center of the flow meter. The DEL Ozone generator will still

perform well at flows above and below the recommended range.

However, the ball must be moving and not stuck on the bottom of

the flowmeter.

5 TROUBLESHOOTING

ENGLISH

13

4-1393-01_Rev.C

D

E

L

O

z

o

n

e

I

n

s

t

a

l

a

t

i

o

n

–

P

l

u

m

b

i

n

g

The DEL Ozone series generators work under vacuum. The injector manifold draws the ozone/air gas mixture out of the

ozone generator and mixes it into the water leaving behind some un-dissolved gas bubbles. These bubbles can affect

certain pool system components, so care must be taken when installing the ozone injector manifold.

The diagrams below cover common plumbing configurations. For other configurations or installation questions, please call

Technical Support at 1 (800) 733-9060, or e-mail: [email protected]

uP

P

o

l

C

l

e

a

n

e

r

s

: Always plumb the cleaner T-fitting before the DEL Ozone injector to prevent gas from affecting the

operation of the cleaner.

vS

S

a

l

t

C

h

l

o

r

i

n

a

t

o

r

:

A salt chlorinator may be plumbed on either side of the DEL Ozone injector.

w

C

h

l

o

r

i

n

e

T

a

b

/

M

i

n

e

r

a

l

E

r

o

s

i

o

n

F

e

d

e

r

:

Always plumb the DEL Ozone injector after any erosion feeder to avoid

gas accumulating in the feeder.

xI

I

n

-

F

l

o

r

C

l

e

a

n

i

n

g

S

y

s

t

e

m

:

The DEL Ozone Injector must be on a different pool return leg than any in-floor

cleaning system to avoid excess back pressure on the injector. This will also prevent gas intrusion and high oxidizer

levels in zone valve and cleaner heads.

yW

W

a

t

e

r

F

e

a

t

u

r

e

s

:

Avoid plumbing the injector manifold into any leg with excessive back pressure such as those

going to fountains, restrictive wall fittings, etc.

Heater

DEL

Ozone

Injector

Manifold

DEL Ozone

In-Floor

Cleaner



Pool

Sanitizer



To Spa

Sanitizer



Water

Features



Diagram 2: Pool/Spa Combo

Diagram 1: Pool Only

Actuator

Heater

Pool

Cleaner



DEL

Ozone

Injector

Manifold

DEL Ozone

Sanitizer



Pool

Sanitizer



Sanitizer



APPENDIX A

ENGLISH

14

NOTES

SAVE THESE INSTRUCTIONS

Record Information on this System Below & Keep for Your Records

Installer ______________________________________________________________

System Purchased From _____________________________________________

Installation Date _____________________________

Serial Number _______________________________

Model Number ______________________________

CMP Customer Service & Tech Support

Toll Free: 1-800-733-9060

FAX: 770-632-7115

suppor[email protected]

Warranty Questions

[email protected]

15

CANADIEN FRANÇAIS

Lisez et suivez toutes les instructions

• Lisez complètement ce manuel avant toute installation. Le fait de ne pas installer le produit en

conformité avec les instructions d’installation peut annuler la garantie et pourrait entraîner des

blessures ou la mort.

• Toutes les connexions électriques permanentes doivent être effectuées par un électricien qualifié.

• Un connecteur de fil à pression, étiqueté « cosse de connexion », est fourni sur l’extérieur de

l’appareil pour permettre de le relier à un conducteur de connexion solide No 6 AWG (13,3 mm2)

au minimum, entre ce point et tout équipement métallique, boîtiers métalliques d’équipement

électrique, tuyaux d’eau métalliques, ou conduit dans un rayon de 1,5 m (5 pi) de l’appareil comme

requis pour se conformer aux exigences locales.

• Si la connexion électrique du générateur DEL Ozone doit être attachée aux commandes de

la piscine, assurez-vous que les commandes de la piscine soient protégées par un disjoncteur

différentiel de fuite à la terre (DDFT). Si le générateur DEL Ozone est connecté à une alimentation

électrique indépendante, alors un DDFT doit être installé entre le générateur DEL Ozone et

l’alimentation électrique.

• Installer à au moins 1,5 m (5 pi) d’une paroi de piscine en utilisant du tubage non métallique. Le

tubage est fourni avec le générateur DEL Ozone. Ne jamais remplacer ce tubage par un tubage

métallique. Ne jamais installer le générateur d’ozone à moins de 0,30 m (1 pi) au-dessus du niveau

d’eau maximum afin d’empêcher l’eau d’entrer en contact avec l’équipement électrique. Installer

en conformité avec les instructions d’installation.

• Suivre les codes électriques applicables.

• Danger de choc électrique: Assurez-vous de couper l’alimentation et débrancher de la source

électrique avant que tout travail de service soit effectué. Le non-respect de cette consigne peut

engendrer des blessures graves ou entraîner la mort.

• Le DEL Ozone® doit être installé à l’extérieur, ou à l’intérieur dans une salle ventilée à air puisé,

et de façon à ce que l’orientation soit exactement comme dans la Figure 1. Installer pour fournir

une vidange d’eau afin de protéger les composants électriques.

• Monter le générateur DEL Ozone® afin qu’il ne soit accessible à personne qui se trouve dans la

piscine. Ne jamais essayer de maintenance lorsque l’appareil est mouillé.

• L’inhalation à court terme de concentrations élevées d’ozone et l’inhalation à long terme de

concentrations faibles d’ozone peuvent provoquer de graves effets physiologiques nocifs. NE

PAS inhaler le gaz d’ozone produit par cet appareil.

• Pour votre sécurité, ne pas entreposer ou utiliser de l’essence, des produits chimiques ou d’autres

liquides ou vapeur inflammables près de celui-ci ou de tout autre appareil ménager.

• Pour réduire le risque de blessures, ne pas permettre aux enfants d’utiliser ce produit, à moins

qu’ils soient étroitement surveillés durant toute l’utilisation.

• Si l’appareil n’est pas utilisé en conformité avec les instructions, des doses élevées de substances

toxiques peuvent potentiellement être libérées.

• AVIS ENVIRONNEMENTAL- L’ampoule Hg-CONTIENT DU MERCURE. Gérer en conformité avec

les lois sur l’élimination. Voir : www.lamprecycle.org.

CONSERVEZ CES INSTRUCTIONS!

INSTRUCTIONS IMPORTANTES

16

CANADIEN FRANÇAIS

TABLE DES MATIÈRES

1 Vue d’ ensemble

1A. Description .................................................................................................... 17

1B. Spécications ............................................................................................... 17

2 Installation

2A. Emplacement ............................................................................................... 17

2B. Montage au mur ......................................................................................... 18

2C. Plomberie ...................................................................................................... 19

2D. Électricité .......................................................................................................22

3 Functionnement

3A. Général ..........................................................................................................23

3B. Démarrage du système initial .................................................................23

3C. Fonctionnement normal ...........................................................................23

3D. Arrêt du système ........................................................................................23

3E. pH de l’eau....................................................................................................23

4 Entretien

4A. Vue d’ensemble électromécanique du système .............................. 24

4B. Entretien du système ................................................................................ 24

4C. Entretien du générateur ...........................................................................25

4D. Coordonnées ...............................................................................................26

4E. Informations sur les commandes ..........................................................26

4F. Liste standard des pièces de rechange ...............................................26

5 Dépannage ............................................................................................................ 27

17

CANADIEN FRANÇAIS

1A. Description

Les générateurs d’ozone DEL Ozone Series décrits dans ce manuel visent

à offrir les avantages d’eau ozonée de manière efficace et écologique. Les

composants de haute-qualité, fabriqués spécialement pour assurer une

production d’ozone efficace et une performance fiable.

Une utilisation correcte des générateurs d’ozone DEL Ozone, éliminent

virtuellement tout effet désagréable lié à l’utilisation traditionnelle de

produits chimiques. Les générateurs d’ozone DEL Ozone sont sans danger

pour votre équipement s’ils sont installés correctement.

1B. Spécifications

Exigences d’alimentation électrique:

Ozone 25 .....................................120/240V, 0.10A max, 50/60Hz

Ozone 50 .....................................120/240V, 0.24A max, 50/60Hz

Ozone 100 ....................................120/240V, 0.31A max, 50/60Hz

Exigences relatives à l’emplacement:

Montage: monter au mur dans une zone propre et protégée.

Température ambiante: entre 2°C et 49°C

2A. Emplacement

Les unités DEL Ozone sont conçues pour un montage au mur. Montez le

générateur dans une zone propre et protégée, à l’intérieur ou à l’extérieur (de

préférence à l’abri de la lumière directe du soleil). Placez le générateur hors de

la portée des arroseurs automatiques ou des évacuations d’eau. Permettez un

accès suffisant pour l’entretien des conduites et fils électriques. Le générateur

d’ozone doit être installé à au moins (minimum) 0,3 mètres au-dessus du

niveau maximum de l’eau.

1 VUE D’ENSEMBLE

La page charge ...

CMP DEL OZONE 25 Generator Le manuel du propriétaire

Ce manuel convient également à

CMP DEL OZONE 25 Generator Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents