Amprobe IR-750-EUR Manuel utilisateur

IR-750

IR-750-EUR

50:1 Infrared

Thermometer

Users Manual

IR-750

IR-750-EUR

50:1 Infrared Thermometer with memory

Users Manual

4/2017, 4279850 D

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for one year from the date of

purchase, unless local laws require otherwise. This warranty does not cover fuses, disposable batteries or damage

from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling.

Resellers are not authorized to extend any other warranty on Amprobe’s behalf. To obtain service during the

warranty period, return the product with proof of purchase to an authorized Amprobe Test Tools Service Center

or to an Amprobe dealer or distributor. See Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY.

ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR STATUTORY - INCLUDING IMPLIED WARRANTIES OF

FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL

NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING

FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or for calibration should be accompanied by the

following: your name, company’s name, address, telephone number, and proof of purchase. Additionally, please

include a brief description of the problem or the service requested and include the test leads with the meter.

Non-warranty repair or replacement charges should be remitted in the form of a check, a money order, credit

card with expiration date, or a purchase order made payable to Amprobe.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During the warranty

period any defective test tool can be returned to your Amprobe distributor for an exchange for the same or

like product. Please check the “Where to Buy” section on www.amprobe.com for a list of distributors near you.

Additionally, in the United States and Canada In-Warranty repair and replacement units can also be sent to a

Amprobe® Test Tools Service Center.

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be sent to a Amprobe Service Center. Call

Amprobe or inquire at your point of purchase for current repair and replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe distributor for a nominal charge. Please check

the “Where to Buy” section on www.amprobe.com for a list of distributors near you.

European Correspondence Address*

Amprobe® Test Tools Europe

Beha-Amprobe GmbH

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

www.amprobe.eu

*(Correspondence only – no repair or replacement available from this address. European customers please

contact your distributor.)

1

IR-750 / IR-750-EUR 50:1 Infrared Thermometer with memory

CONTENTS

SYMBOLS ...................................................................................................................................................................... 3

SAFETY INFORMATION ................................................................................................................................................ 3

UNPACKING AND INSPECTION .................................................................................................................................... 4

FEATURES ...................................................................................................................................................................... 4

HOW THE THERMOMETERS WORK ............................................................................................................................ 4

OPERATING THE THERMOMETER ................................................................................................................................ 4

Temperature Measurement .................................................................................................................................... 4

Locating a Hot or Cold Spot ................................................................................................................................... 8

Distance and Spot Size ............................................................................................................................................ 8

Field of View.............................................................................................................................................................8

Emissivity .................................................................................................................................................................. 9

Reminders ................................................................................................................................................................ 9

TYPICAL MEASUREMENTS .......................................................................................................................................... 10

OPERATING IR-750 / IR-750-EUR SOFTWARE ............................................................................................................. 13

DETAILED SPECIFICATIONS ......................................................................................................................................... 17

MAINTENANCE ............................................................................................................................................................. 18

TROUBLE SHOOTING .................................................................................................................................................... 19

BATTERY REPLACEMENT .............................................................................................................................................19

2

IR-750 / IR-750-EUR 50:1 Infrared Thermometer with memory

1

Laser aperture

2

Trigger

3

Battery cover

4

Display

5

USB connector

6

K-type thermocouple connector

7

Power adaptor connector (for optional accessory)

8

Laser “ON” symbol

9

Display backlight

10

Measurement lock (continuous measurement)

11

Temperature unit (Celsius / Fahrenheit)

12

8 seconds auto display hold

13

Making measurement (pulling the trigger)

14

Built in memory up to 99 points

15

Programmable high and low alarm

16

Low battery indicator

17

Primary display

18

Secondary display

19

Emissivity (adjustable from 0.10 to 1.00)

20

MAX, MIN, DIF, AVG temperature values

HAL, LAL temperature setting

DATA point selection

T-C K-type thermocouple measurement

1

5

6

7

4

89

2 3

17

12

1613

10

11

15

18

19

14

20

3

SYMBOLS



Caution! Refer to the explanation in this Manual.

Warning! Laser light. Do not stare into laser beam.

°C

Celsius.

°F

Fahrenheit.

Battery indication.



Complies with European Directives.



Do not dispose of this product as unsorted municipal waste.

Contact a qualified recycler.

SAFETY INFORMATION

The instrument complies with:

EN 61010-1 General Safety

EN 60825-1 Laser Safety

EN 61326-1 Electromagnetic Emissions and Susceptibility



Warning

• Do not stare into laser beam.

• Do not point laser directly at eye or indirectly off reflective surfaces.

• For use by competent persons only.

• Replace the batteries as soon as the low-battery indicator appears.

• Do not use the thermometer if it operates abnormally.

• Do not operate the thermometer around explosive gas, vapor, or dust.

• To avoid a burn hazard or fire, know that reflective objects may be much hotter than the indicated

temperature reading.

• Do not leave the thermometer on or near objects of high temperature.

• If the thermometer is used in a manner not specified by this manual, the protection provided by the

thermometer may be impaired or may result in hazardous laser radiation exposure.



Cautions

To avoid damaging the thermometer under measurement, protect them from the following:

• EMF (electro-magnetic fields) from arc welders, induction heaters

• Static electricity

• Thermal shock (caused by large or abrupt ambient temperature changes — allow 30 minutes for instrument to

stabilize before use)

• Do not leave the thermometer on or near objects of high temperature

4

UNPACKING AND INSPECTION

Your shipping carton should include:

1 Thermometer (IR-750 / IR-750-EUR)

1 USB cable

1 K-type thermocouple probe

1 Carrying case

1 Hard carrying case

1 9V battery (installed)

1 Users manual

If any of the items are damaged or missing, return the complete package to the place of purchase for an

exchange.

FEATURES

The Amprobe IR-750 / IR-750-EUR, a precision performance 50:1 spot to distance ratio infrared thermometer,

offers unparalleled accuracy and response time with a temperature measurement range of -58°F to 2822°F

or -50°C to 1550°C. The IR-750 / IR-750-EUR is perfect for demanding quality and process control applications

with extremely high accuracy and distance to spot ratio. The IR-750 / IR-750-EUR also features 99 data points

recognition, thermocouple inputs, and USB download for advanced HVAC/R, electrical, industrial maintenance,

automotive as well as quality control and fire prevention applications.

• 50:1 Distance to Spot ratio

• Temperature range of 0°F to -58°F to 2822°F or -50°C to 1550°C

• Precision accuracy and rapid response time

• Laser pointer, backlit dual LCD Display

• Auto display hold and MAX/MIN memory

• Adjustable emissivity for measuring a variety of materials

• 99 Memory locations and PC download cable included

HOW THE THERMOMETERS WORK

Infrared thermometers measure the surface temperature of an object. The thermometer’s optics sense emitted,

reflected, and transmitted energy, which is collected and focused onto a detector. The unit’s electronics translate

the signal into a temperature reading which the unit displays .

OPERATING THE THERMOMETER

Temperature Measurement

The thermometer will turn on when you pull the trigger and also features an auto-off function that

automatically powers down the thermometer after 8 seconds of inactivity.

To measure temperature, point the thermometer at an object and pull the trigger. You can use the laser pointer

to help aim the thermometer. Pull and hold the trigger when measuring the target surface. When release the

trigger, the display will hold the reading for 8 seconds. Be sure to consider distance-to-spot size ratio and field of

view. The laser is used for aiming only and is not related to temperature measurement.

5

Rotary Switch Positions

Button Description

YELLOW

button

Press YELLOW button to toggle between MAX, MIN, DIF, AVG, HAL, LAL, DATA and

T-C options. When the Thermometer goes into sleep mode, press MODE to turn the

thermometer ON again and it displays the last measurement result.

SET

Press to enter set-up mode stepping through Emissivity, Trigger Lock and Switching °C/°F

set-up.

Details refer to the below Emissivity, Trigger Lock and °C / °F set-up.

Press

to turn the display backlight ON or OFF.

Selectable two level of display backlight to adapt different lighting conditions.

Press to turn the laser light ON or OFF.

symbol on the display Indicates laser light is ON.

/

When the thermometer enters the setup up mode (SET), press or to select a set-up

option (Emissivity, Trigger lock, Switching °C / °F).

When the thermometer enters HAL, LAL and DATA mode, press

or to select a set-up

option (Emissivity, Trigger lock, Switching °C / °F).

Laser



Caution

To avoid injury, do not point the laser directly at eye or indirectly off reflective surfaces.

The thermometer is equipped with a laser used for aiming purposes only. The laser turns off when the trigger

is released.

To enable or disable the laser:

1. Press

button to enable or disable the laser. Symbol appears on the display when laser is enabled.

Emissivity set-up

1. Press SET button to select Emissivity set-up, icon is blinking on the display

2. Press

to increase the value by 0.01. Press and hold for quick setting. The maximum value is 1.00.

3. Press

to decrease the value by 0.01. Press and hold for quick setting. The minimum value is 0.01.

4. Press MODE button to complete the setting and exit Emissivity set-up, or press SET button to complete the setting

and continue setting for Trigger Lock.

Note: Default emissivity is 0.95.

6

Table of Surface Emissivity

Measure Surface Switch Setting

METALS

Aluminum

Oxidized 0.2 – 0.4

Alloy A3003

Oxidized 0.3

Roughened 0.1 – 0.3

Brass

Burnished 0.3

Oxidized 0.5

Cooper

Oxidized 0.4 – 0.8

Electrical Terminal Blocks 0.6

Haynes

Alloy 0.3 – 0.8

Inconel

Oxidized 0.7 – 0.95

Sandblasted 0.3 – 0.6

Electoropolished 0.15

Iron

Oxidized 0.5 – 0.9

Rusted 0.5 – 0.7

Iron Cast

Oxidized 0.6 – 0.95

Unoxidized 0.2

Molten 0.2 – 0.3

Iron Wrought

Dull 0.9

Lead

Rough 0.4

Oxidized 0.2 – 0.6

Molydbenum

Oxidized 0.2 – 0.6

Nickel

Oxidized 0.2 – 0.5

Platinum

Black 0.9

Steel

Cold-Rolled 0.7 – 0.9

Ground Sheet 0.4 – 0.6

Polished Sheet 0.1

Zinc

Oxidized 0.1

Measure Surface Switch Setting

NON-METALS

Asbestos 0.95

Asphalt 0.95

Basalt 0.7

Carbon

Unoxidized 0.8 – 0.9

Graphite 0.7 – 0.8

Carborundum 0.9

Ceramic 0.95

Clay 0.95

Concrete 0.95

Cloth 0.95

Glass

Plate 0.85

Gravel 0.95

Gypsum 0.8 – 0.95

Ice 0.98

Limestone 0.98

Paper (any colour) 0.95

Plastic

Opaque 0.95

Soil 0.9 – 0.98

Water 0.93

Wood, (natural) 0.9 – 0.95

7

Trigger Lock

The thermometer trigger can be locked on for continuous measurement.

To lock the trigger:

1. Press SET button to select Trigger Lock set-up, icon

is blinking on the display

2. Press

or to select ON or OFF.

3. Press YELLOW button to complete the setting and exit Trigger Lock set-up, or press SET button to complete the

setting and continue setting for °C / °F.

°C / °F Set-up

1. Press SET button to select °C / °F set-up, icon °C or °F is blinking on the display

2. Press

or to select °C or °F.

3. Press YELLOW button to complete the setting and exit °C / °F set-up.

MAX, MIN, DIF, AVG

The thermometer can measure maximum (MAX), minimum (MIN), differential (DIF) or average (AVG)

temperatures each time a reading is taken. These values are available for infrared measurements.

1. Press YELLOW button until MIN or MAX or AVG or DIF appears on the display

2. Pull and hold the trigger while aiming at the target surface.

3. The value will show on secondary display.

High Alarm (HAL) and Low Alarm (LAL)

The thermometer has a programmable high and low alarm to designate high or low readings depending on

the thresholds entered. When the alarm level is reached, an alarm will sound. This feature is not available when

measuring by thermocouple.

To set either the high or low alarm:

1. Press YELLOW button to select HAL or LAL option.

2. Press

or to adjust the threshold value.

3. Press SET button to complete the setting. Symbol

or

will appear on the display.

To turn off the high or low alarm:

1. Press YELLOW button to select HAL or LAL option.

2. Press SET button. Disappearance of Symbol

or

on the display indicates high or low alarm is off.

DATA Memory

The thermometer has 99 points data storage and the stored data can be downloaded via IR-750 / IR-750-EUR

software. To save the data:

1. Press YELLOW button to select DATA option.

2. Press

or to select data record number

3. Pull and hold the trigger while aiming at the target surface, press DATA button to save the measurement value.

To erase the saved data, when the thermometer is in standby mode (screen is off), press and hold “DATA” and

“

” button while pulling the trigger until a beep occurs. The data records on screen displays “ – – – – “, all

saved data is cleared.

K-Type Thermocouple Measurement



To avoid electrical shock or personal injury, do not connect the thermocouple contact probe to live

electrical circuits.

The thermometer comes with a bead K-type thermocouple probe.

K-type thermocouple is connected to the thermometer via TC-K input connector located on right side of

the thermometer. The probe can be used simultaneously while the thermometer is taking non-contact

measurements.

1. Press YELLOW button to enter T-C mode. The display shows OL before the measurement is made.

2. Connect the K-type thermocouple to the thermometer via TC-K input connector located on right side of

the thermometer. Press the trigger to start measuring. Secondary display shows the measurement reading.

3. Release the trigger, the reading is kept on display (display hold: 8 seconds)

8

Locating a Hot or Cold Spot

To find a hot or cold spot, aim the thermometer outside the target area. Then, slowly scan across the area with

an up and down motion until you located the hot or cold spot.

Distance and Spot Size

As the distance (D) from the target being measured increases, the spot size (S) of the area measured by the

instrument becomes larger. The spot size indicates 90% encircled energy.

Field of View

Make sure that the target is larger than the spot size. The smaller the target, the closer you should be to it.

9

Emissivity

Emissivity describes the energy-emitting characteristics of materials. Most organic materials and painted or oxidized

surfaces have an emissivity of about 0.95.

If possible, to compensate for inaccurate readings that may result from measuring shiny metal surfaces, cover

the surface to be measured with masking tape or flat black paint (<150°C / 302°F ) and use the high emissivity

setting. Allow time for the tape or paint to reach the same temperatures as the surface beneath it. Measure the

temperature of the tape or painted surface.

If you cannot use paint or use tape, then you could improve the accuracy of your measurements with the

emissivity selector. Even with emissivity selector, it can be difficult to get a completely accurate infrared

measurement of a target with a shiny or metallic surface.

The thermometer allows you to adjust the emissivity for the type of surface you’re trying to measure the

temperature of. Use a different setting for your application by referring to the Table of Surface Emissivity.

Reminders

1. Changes of surrounding ambient temperature can result in inaccurate reading, allow time for the

instrument to adopt the change of ambient temperature before use. Specified accuracy applies after 30

minutes when the instrument changes to a different temperature environment an inaccurate.

2. The instrument cannot measure through transparent surfaces such as glass. It will measure the surface

temperature of the glass instead.

10

3. See Table of Surface Emissivity for use in measuring shiny or polished metal surfaces (stainless steel,

aluminum, etc.).

4. Steam, dust, smoke, etc., can prevent accurate measurement by obstructing the instrument’s optics.

TYPICAL MEASUREMENTS

This section describes a variety of measurements often performed by technicians.

Reminder:

• User could select to turn on or off the backlight and laser whenever you are making readings with the

thermometer.

• Relatively high emissivity normally means emissivity setting of about 0.95.

• Relatively low emissivity normally means emissivity setting of about 0.30.

• When user cannot identify the emissivity of the object to be measured, user could cover the surface to be

measured (temperature >150°C) with black electric tape (emissivity of about 0.95). Allow time for the tape

to reach the same temperature as the object to be measured. Measure and record the temperature of the

tape.

Aim the thermometer to the object to be measured, adjust the emissivity setting to make it as the same temperature

as the tape. At this time, the thermometer emissivity setting is close to the emissivity of the object to be measured,

measurement can be taken.

Testing Contactors (Starters)

1. Press SET to select emissivity. Press / to select relatively low emissivity for bright contacts, or 0.7 mid

level for darkened contacts.

2. Press YELLOW button to select MAX.

3. Measure line and load side of one pole without releasing trigger.

4. A temperature difference between the line and load sides of a pole indicate increased resistance of one

point and a contactor may be failing.

Testing Enclosed Relays

1. Press SET and then press / to set emissivity to relatively low for un-insulated connectors or relatively

high for plastic encased relays or for Bakelite enclosed relays or insulated connectors.

2. Press YELLOW button to select MAX.

3. Start to scan.

4. Measure the relay casing, looking for hot spots.

5. Measure electrical connections on relay terminals looking for hot spots.

11

Testing Fuses and Buss Connections

1. Press SET and then press / to set emissivity to relatively high for paper covered fuse body or

insulated connections.

2. Press YELLOW button to select MAX.

3. Scan the paper covered length of fuse.

4. Without releasing the trigger, scan each fuse. Unequal temperatures between fuses may indicate voltage or

amperage imbalance.

5. Press SET and then press / to set emissivity to relatively low, for metal fuses and caps and insulated

buss connections.

6. Press MODE to select MAX.

7. Scan each end cap on each fuse.

Note: Unequal temperatures or a high temperature indicates loose or corroded connection through the fuse

buss spring clip

Testing Electrical Connections

1. Press SET and then press / to set emissivity to relatively low for

un-insulated connectors or buss connections or relatively high for insulated connections.

Note: Conductors are typically smaller than the thermometer’s spot size.

If the spot size is bigger than the connector, the temperature reading is the average within the spot.

2. Scan the conductor, moving toward direction of electrical connector (quick connector, wire nut, buss

connection, etc.).

Scanning Walls for Air Leaks or Insulation Deficiencies

1. Turn off heating, cooling, and blower.

2. Press SET to select emissivity. Press

/ to select emissivity relatively high for painted surfaces or

window surfaces.

3. Press YELLOW button to select MIN when opposite side of wall is at lower temperature and or select MAX

when opposite side of wall is at higher temperature.

4. Measure an interior partition wall surface temperature.

5. Do not release the trigger. Record this temperature as your baseline (or benchmark) for a “perfectly”

insulated wall.

6. Face the wall to be scanned. Stand 1.5m away to scan a 4cm spot on the wall.

7. Scan horizontal rows of wall from top to bottom, or horizontal rows of ceiling from wall to wall. Look for

greatest deviations from baseline temperature to identify problems. This completes the insulation test scan.

Turn on the blower (no heat, no cooling) and retest. If test results with the blower on are different than results

with the blower off, this may indicate air leaks in conditioned envelope walls. The air leaks are caused by duct

leaks that create a pressure differential across the conditioned space envelope.

Testing Bearings



Warning

To avoid injury when testing bearings:

1. Do not wear loose clothing, jewelry, or anything around neck when working around moving parts such as

motors, belts, blower, and fans.

2. Make sure an electrical disconnect is within reach and operating correctly and freely.

3. Do not work alone.

Note: It works best to compare two similar motors operating similar loads

12

1. Press SET and then press

/ to select relatively high emissivity.

2. Press SELECT to select MAX.

3. Enable motor and allow it to reach steady state operating temperatures.

4. Disable the motor if possible.

5. Measure the two motor bearing temperatures.

6. Compare the two motor bearing temperatures. Unequal temperatures or a high temperature can indicate

a lubrication or other bearing problem that is resulting from excess friction.

7. Repeat the sequence for the blower bearings.

Testing Belts and Sheaves

1. Press SET and then press / to select relatively high emissivity.

2. Press SELECT to select MAX.

3. Enable the motor and allow it to reach a steady state operating temperatures.

4. Aim the thermometer at the surface to be measured.

5. Start recording temperature.

6. Slowly move the thermometer up the belt toward second sheave.

• If belt is slipping, sheave temperature will be high from friction.

• If belt is slipping, belt temperature will remain high between sheaves.

• If belt is not slipping, belt temperature will reduce between sheaves.

• If inner surfaces of sheaves are not a true “V” shape, this indicates belt slippage and will continue to

operate at elevated temperatures until sheave is replaced.

• Sheaves must be properly aligned (include “pitch & yaw”) for belt and sheaves to operate at

appropriate temperatures. A straight edge or taut string, can be used to check alignments.

• Motor sheave should operate at a temperature consistent with blower sheaves.

• If motor sheave is at a higher temperature at motor shaft than at outer circumference, belt is probably

not slipping.

• If outer circumference of sheave is at higher temperature than sheave at motor shaft, then belt is probably

slipping and sheaves may be misaligned.

Checking Hydronic Radiant Heat Applications

1. Press SET and then press / to select relatively high emissivity.

2. Press YELLOW button to select MAX.

3. To locate radiant heat tubes in floor, temporarily elevate the loop temperature to create hotter spots for

identifying tubing runs.

4. Before releasing trigger, press YELLOW button to toggle between MIN, MAX, DIF floor temperatures and

record the temperature for future comparison and trending under similar conditions.

Measuring Grill, Register, or Diffuser Discharge Temperature

1. Press SET and then press / to select relatively high emissivity.

2. Aim the thermometer at the discharge air grille, register, or diffuser.

3. Measure discharge temperature.

4. Release trigger to freeze the temperature reading for 8 seconds and record this temperature.

5. Grille, register, or diffuser temperature should be equivalent to discharge temperature at the air handler.

13

Checking for Blockage in Air-To-Air Evaporator or Condensers

1. Remove panels to gain access to coil return bends or hairpins.

2. Press SET and then press

/ to select relatively high emissivity for copper tube.

3. Start the refrigeration system.

4. Aim the thermometer at coil turn bends/hairpins.

5. Start recording temperature.

6. Take temperature of each return bend/hairpin.

• All evaporator return bends/hairpins should be at or slightly above evaporator saturation temperature from the

pressure/temperature chart.

• All condenser return bend/hairpins should be at or slightly less than condenser saturation temperature.

• If a group of return bends/hairpins do not conform to expected temperatures, that indicates a blocked

or restricted distributor or distributor tube.

OPERATING IR-750 / IR-750-EUR SOFTWARE

System Prerequisites

Recommended configuration

Processor Pentium® 4 or higher with support of all customary operating systems

Operating system Microsoft Windows® 2000 / XP / Vista / Win7

Memory 512 MB RAM or higher

Monitor VGA (1024 x 768)

Drive CD-ROM

Input device Mouse or compatible

Interface USB for data transmission

Install IR-750 / IR-750-EUR Software

• Insert the provided CD disk into CD-ROM drive.

• Double-click “IR-750_VX.XX.exe” (X can be 0 to 9 or blank,

indicating the software version)

• The pop-up windows will guide you through the program setup process.

Connecting USB cable to IR-750 / IR-750-EUR Thermometer

14

Main Screen

1

command enables you to create New, Save file and set the numbers of measurement (1000, 5000,

10000, 50000, 100000 or limitless).

2

command enables you to view the software operation instructions.

3

Blinking indicates IR-750 / IR-750-EUR is connected to the software

4

Main display screen of measurement

5

Secondary display screen for measurement data

6

Measurement data in graph

Using Program

button enables you to connect to IR-750 / IR-750-EUR thermometer and start measurement. “USB

Connect” blinking indicates that the IR-750 / IR-750-EUR Thermometer is successfully connected to the

PC and that the thermometer will automatically start taking measurements. The primary display screen shows

current measurement temperatures and the secondary display screen shows all measurement data.

Download Data enables you to download temperature measurements saved in IR-750 / IR-750-EUR Thermometer.

Tick “Download Data” and then click “USB Connect”; the saved data will automatically upload to your PC and

display on secondary display.

Exit and close the program

1

Print data

2

Save data (*.txt, *.xls, *.xml)

3

Open files (*.txt, *.xls, *.xml)

4

Deleting current data and create a new data.

1

2

3

4

5

6

1

2

3

4

15

Repeat: Tick to display every measurement with the interval you set. Un-tick “Repeat”, the secondary display will

only show measurement results that are different from the last measured temperature. The graph display will

show complete measurement results in the graphics despite whether “Repeat” is ticked or un-ticked.

Sampling Interval allows you to set the sampling intervals of measurement ( 1 to 9999 seconds).

Note: When measurement data reaching to 10000 sets (measurement number), a warning message will pop up

and stop measurements. Save or clear the measurement data before continuing next measurements.

1

Last page

5

First page

2

Save graph in current page as *.bmp

3

Current page

7

Set numbers of measurement data on graph display

4

Test data can be saved as *.txt, *.xls, *.xml by clicking button. When opening data report, make sure

selecting font format as Amprobe-A1 or Amprobe-A2 in “Unit” column in order to display correct temperature

unit °C or °F.

1

2

3

4

5

6

7

16

Zoom In Selected Graph

To enlarge the particular part of the graph, use the mouse pointer to select area from upper-left point to lower-right

point.

You can use button to save the selected enlarged graph.

To resume to its original full view, use the mouse pointer to select any area on the graph from lower-right point

to upper-left point.

La page charge ...

Amprobe IR-750-EUR Manuel utilisateur

Ce manuel convient également à

Amprobe IR-750-EUR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents