Danby DDW2404EBSS Le manuel du propriétaire

Marque: Danby

Modèle: DDW2404EBSS

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

DDW2404EBSS

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

2018.02.08

DISHWASHER

Owner’s Manual............................1 - 14

LAVE-VAISSELLE

Manuel du propriétaire................15 - 28

LAVAPLATOS

Manual del propietario................29 - 42

MODEL • MODÈLE • MODELO

DDW2404EBSS

Welcome

Welcome to the Danby family. We are proud of our quality products and we believe in

dependable service. We suggest that you read this owner’s manual before plugging in your new

appliance as it contains important operation information, safety information, troubleshooting and

maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance

call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

You must provide the original purchase receipt to validate your warranty and receive service.

Model Number: _________________________________________________

Serial Number: _________________________________________________

Date of Purchase: _______________________________________________

Need Help?

Before you call for service, here are a few things you can do to help us serve you better.

Read this owner’s manual:

It contains instructions to help you use and maintain your appliance properly.

If you receive a damaged appliance:

Immediately contact the retailer or builder that sold you the appliance.

Save time and money:

Check the troubleshooting section at the end of this manual before calling. This section

will help you solve common problems that may occur.

1-800-26- Danby

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

SAFETY REQUIREMENTS

• Children should be supervised to ensure that

they do not play with the appliance.

• Do not stand, sit or lean on the door or dish

rack. Do not place heavy items on the door

when it is open.

• Do not touch the heating element during or

immediately after use.

• Do not operate the appliance unless all

enclosure panels are properly installed.

• Open door carefully during operation, water

may leak. Proceed with caution as water may be

hot.

• Do not wash plastic items unless they are

marked dishwasher safe.

• Use only detergent and rinse additives that are

designed for an automatic dishwasher.

• Never use soap, laundry detergent or hand

washing detergent in the dishwasher.

• Keep detergent and rinse aid out of the reach of

children.

• Check that the detergent dispenser is empty after

completion of the wash cycle.

• Dishwasher detergents are strongly alkaline and

can be extremely dangerous if swallowed. Avoid

contact with the skin and eyes.

• Remove the door of the appliance when

removing from service or discarding.

• The hot water supply line pressure must be

between 0.04 - 1 MPa.

• The water supply inlet temperature should be

between 48 - 65°C (120 - 149°F).

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electrical shock by providing an escape wire for the

electrical current.

This appliance is equipped with a cord that has a

grounding wire and grounding plug. The power

cord must be plugged into an outlet that is properly

grounded. If the outlet is a 2-prong wall outlet, it

is your responsibility to have it replaced with a

properly grounded 3-prong wall outlet. The serial

rating plate indicates the voltage and frequency the

appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁ ed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

DO NOT USE AN EXTENSION CORD

Do not connect your appliance to extension cords

or together with another appliance in the same wall

outlet. Do not splice the power cord. Do not under

any circumstances cut or remove the third ground

prong from the power cord.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁ ed person in order to avoid hazard.

Ensure that component parts are replaced with like

components and that servicing is done by factory

authorized service personnel to minimize the risk of

possible ignition due to incorrect parts or improper

service.

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

INSTALLATION INSTRUCTIONS

ACCESSORIES

1. ST3.5*9 screws for the installation brace (x2)

2. ST3.9*13 screws for the kick plate (x2)

3. ST4*14 screws for the installation brace (x2)

4. Condensation strip

5. Installation brace (x2)

6. Adjustment caps (x2)

7. Kick plate

8. Cable tie to secure the drain hose

ENCLOSURE

The installation location must have a solid ﬂ oor

that is able to support the appliance when it is fully

loaded and ﬁ lled with water. The location must be

within 3 meters of a sink with easy access to the

water supply, the drain and an electrical outlet. The

location must have enough space in front of it for

the door to open to 90° so that the dishwasher can

be loaded.

The installation enclosure should have the following

dimensions: 23.6 inches (60 cm) wide by 32.5

inches (82.5 cm) tall by 22.8 inches (58 cm) deep.

There should be less than 5 mm between the top of

the dishwasher and the cabinet and the dishwasher

door should align with the cabinet face.

If necessary, cut holes in the surrounding cabinetry

to provide access the water and power connections.

WATER CONNECTION INSTRUCTIONS

The hot water supply line pressure must be between

0.04 - 1 MPa.

The water supply inlet temperature should be

between 48 - 65°C (120 - 149°F). Ensure that the

water temperature does not exceed 65°C (149°F) to

avoid damage to dishes.

Ensure that the circuit breaker and the water supply

valve are turned off before connecting the hot water

supply line to the dishwasher.

The power cable will connect to the junction box on

the front right side of the appliance. The hot water

supply line will connect to the water port on the

front left side of the appliance.

Note: It is recommended to only use soft water in

the appliance to achieve the best washing results.

90 r

23.6 inches

(60 cm)

90 r

32.5 inches

(82.5 cm)

22.8 inches

(58 cm)

Power cable

Hot water

supply line

135 - 185 mm

(5 1/3 - 7 1/3”)

INSTALLATION INSTRUCTIONS

Connecting the hot water line

Run the hot water line through the channel on the

bottom left side of the appliance. Make sure the hot

water line is not twisted and then connect it to the

back of the appliance using an elbow joint. Use

Teﬂ on tape or sealing compound on the connection

to avoid leaks.

Do not over tighten the 90° elbow. This can damage

the water inlet and cause a leak.

Connecting the drain line

The drain hose will connect to the drain pump on

the bottom of the appliance. Run the drain line in

the same channel on the bottom of the appliance

as the hot water line. Ensure there is nothing inside

the drain hose and that it does not tear during the

installation process.

There are a number of different ways to connect

the drain hose depending on the conﬁ guration of

the sink. Review the different ways of connecting

the drain system and choose a method that best

suits the application. Local codes may require the

installation of an air gap kit. Check with a qualiﬁ ed

plumber if there is any doubt.

1. Air gap

2. Air gap with garbage disposal

3. No air gap

4. No air gap with garbage disposal

Use a rubber connector to connect drain hoses and

hose clamps on all connection points.

Secure the drain hose to the sink wall using cable

ties or other fastening materials. If not fastened, the

drain hose may bend causing drainage problems.

The drain hose internal diameter is 0.8 inches (21

mm).

The top of the drain hose must be less than 39

inches (100 cm) from the ﬂ oor.

If the drain hose is not looped up the water may

siphon out during a wash cycle.

Any bends in the drain hose must be supported so

that the hose will not kink or bend.

INSTALLATION INSTRUCTIONS

WIRING CONNECTION INSTRUCTIONS

Before connecting the power cable to the

dishwasher, make sure the circuit breaker is off.

In the junction box located at the front bottom right

of the dishwasher, ﬁ nd the three power wires from

the dishwasher including the grounding line.

Pass the power cable through the strain relief, and

then into the junction box.

Connect the black wire of the dishwasher to the

black wire of the power cable by inserting both into

a wire nut and then rotating the wire connector.

Connect the white wire to the white wire and the

green to the green in the same manner.

Recheck each wire to ensure it is connected correctly

and securely.

Each colored wire should be connected to the

corresponding wire of the same color.

White should be connected to white, black to black,

and green to green.

Replace the junction box cover on the dishwasher.

Recheck each wire to ensure it is connected

correctly and securely. Each coloured wire should

be connected to the corresponding wire of the same

colour.

WARNING ELECTRICAL SHOCK HAZARD

To avoid electrical shock, do not work on an

energized circuit. Doing so could result in serious

injury or death. To avoid a ﬁ re hazard, make sure

electrical work is properly installed. Only qualiﬁ ed

electricians should perform electrical work.

1. Junction box

2. Power cable

3. Black to black

4. White to white

5. Green to green (ground to ground)

6. Strain relief

INSTALLATION INSTRUCTIONS

CONDENSATION STRIP

Attach the condensation strip under the work

surface of the cabinet. Ensure that the strip is ﬂ ush

with the edge of the work surface.

LEVELING INSTRUCTIONS

Ensure that the appliance is level before placing it

into the enclosure. The rear foot can be adjusted

from the front of the dishwasher by turning. Use

a ﬂ at screwdriver to adjust the front feet until the

appliance is level.

INSTALLATION BRACES

The appliance must be secured in place with the

installation braces. There are two different ways to

use the braces.

A. Normal work surface

Put the installation hook into the slot of the side

plane and secure it to the work surface with the

wood screws.

B. Marble or granite counter top

Fix the side with the screw. Place the screw covers

over the internal screws to protect them from water.

TOE KICK INSTALLATION

Install the toe kick on the bottom of the appliance.

OPERATING INSTRUCTIONS

3 4

6 7 8

CONTROL PANEL

1. Power button: Use to turn the appliance on or off.

2. Handle

3. Programs: The light will illuminate to show which program has been selected.

A: Heavy wash

B: Normal wash

C: ECO wash

D: Glass wash

E: Rapid wash

F: Rinse

4. Features: The light will illuminate to show which features have been selected.

G: High temp wash - water temperature will be maintained at 60°C (140°F)

H: Heated dry - the heater will operate during the drying cycle

I: Sanitize - water temperature will be maintained at 69°C (156°F)

J: Rinse aid indicator light - light will illuminate when the rinse aid dispenser is empty

K: Cycle end indicator light - light will illuminate when the program is ﬁ nished

L: Faucet warning indicator light - light will illuminate when the appliance is not receiving enough

water; turn on the nearby water faucet to correct the water ﬂ ow

5. Display screen: Shows the remaining running time in the current program.

6. Program button: Press to select the desired program.

7. Features button: Press to select the desired features.

8. Timed delay button: Press to set the desired time delay.

9. Start/Cancel button: Press to start the desired program. Press to cancel a program which it is in

operation.

OPERATING INSTRUCTIONS

SMART WASH SYSTEM

This appliance is equipped with a Smart Wash

System. When a partial load of lightly soiled dishes

is placed in the appliance, a wash cycle similar to a

short wash will automatically be performed.

When a full load of heavily soiled dishes is

placed in the appliance, a heavy wash cycle will

automatically be performed.

When a cycle is running, the remaining time could

suddenly increase or drop several minutes. This

indicates that the Smart Wash System has checked

the soil level and determined in additional water ﬁ lls

are needed or if water ﬁ lls can be deleted.

Program Cycle Description Cycle Breakdown Running Time Water Use

Heavy For heavily soiled loads such

as pots and pans

Pre-Wash

Wash (60°C)

Rinse (65°C)

Rinse (with sani 69°C)

Drying

155 minutes 21.5 litres

(5.7 gallons)

Normal For normally soiled loads;

standard daily cycle

Pre-Wash

Wash (50-55°C)

Rinse (58-60°C)

Rinse (with sani 69°C)

Drying

100~130 minutes 10.5~21.5 litres

(2.8~5.7 gallons)

ECO Energy conserving cycle for

lightly soiled loads

Pre-Wash

Wash (45-50°C)

Rinse (50-55°C)

Rinse (with sani 69°C)

Drying

115 minutes 18 litres

(4.8 gallons)

Glass For lightly soiled glassware Pre-Wash

Wash (48-50°C)

Rinse (50-55°C)

Drying

105 minutes 18 litres

(4.8 gallons)

Rapid A fast cycle for lightly soiled

loads

Pre-wash

Wash (50°C)

Rinse (50°C)

60 minutes 14 litres

(3.7 gallons)

Rinse Rinse cycle only Pre-Wash

Wash

20 minutes 7.5 litres

(2 gallons)

WASH CYCLE TABLE Press the program button to select the desired wash program.

Note: Cycle times are approximate and will vary based on the options selected.

CHILD LOCK FUNCTION

Press and hold the features button and the time

delay button for three seconds to engage the child

lock function. The display screen will show a lock

icon and the buttons on the control panel will not

respond. Press and hold the features button and the

time delay button for three seconds to disengage the

child lock function.

OPERATING INSTRUCTIONS

LOADING THE DISHWASHER

• Scrape all dishes to remove any large food

residue before placing in this appliance.

• Only place dishes in this appliance that are

marked as dishwasher safe.

• Use a mild detergent.

Items that should not be placed in a dishwasher

• Cutlery with wooden, bone china or mother-of-

pearl handles.

• Plastic items that are not heat resistant.

• Items that have been repaired with glue that is

not heat resistant.

• Pewter, copper or steel items.

• Wooden platters.

• Items made from synthetic ﬁ bers.

• Items with glazed patterns may fade if machine

washed frequently.

Tips for efﬁ cient loading

• Load hollow items such as cups, glasses or

pans with the opening downward so that water

cannot collect in the container.

• Items must not lie inside one another or cover

one another.

• To avoid damage to glasses, they should not

touch.

• Sharp items of cutlery such as carving knives

should be loaded horizontally in the basket to

avoid injury when unloading.

• Do not overload the appliance.

LOADING THE CUTLERY BASKET

Cutlery should be placed in the cutlery basket with

the handles facing down. Ensure that cutlery items

do not nest inside of one another as this can affect

cleaning performance.

Sharp or pointed items should be placed in the

cutlery basket with points facing down to avoid

injury when unloading.

Do not place excessively small items into the

dishwasher as they could fall through the basket

and impact the operation of the appliance.

LOADING THE UPPER BASKET

The upper basket is designed for cups, glasses,

small plates, bowls and plastic items that are

marked dishwasher safe.

Make sure the loaded dishes do not interfere with

the rotation of the spray arm located on the bottom

of the upper basket.

LOADING THE LOWER BASKET

The lower basket is designed for dinner dishes, soup

bowls, plates, pots, lids, casserole dishes and plates.

Load large items such as pans and pots should be

loaded with their open sides facing downwards.

DETERGENT DISPENSER

The detergent dispenser must be ﬁ lled before the

start of each wash cycle. Add the detergent just

before starting the wash cycle. Adding the detergent

to the appliance too soon can cause it to become

damp and it may not dissolve properly.

1. If the detergent dispenser is closed, press the

latch to open it.

2. Add the recommended amount of detergent to

the main detergent component.

3. Close the ﬂ ap by sliding it to the left and

pressing down.

RINSE AID DISPENSER

Rinse aid can be used to prevent water droplets or

streaks from forming on dishes. The rinse aid will be

released automatically during the ﬁ nal rinse. This

appliance is designed to use liquid rinse aid only.

Do not use a powdered rinse aid as it will clog the

reservoir opening. Do not put any other substance

in the rinse aid dispenser as this can damage the

appliance.

1. Open the rinse aid dispenser by lifting the lid.

2. Use the viewing port when ﬁ lling the rinse aid

reservoir. Do not ﬁ ll the reservoir above the full

level indicator.

3. If the display screen shows “LSb”, the rinse aid

dispenser is empty.

4. Close the rinse aid cap by pressing down.

OPERATING INSTRUCTIONS

STARTING A WASH CYCLE

1. Load the dishwasher as per the loading

instructions.

2. Add detergent and rinse aid as required.

3. Close the dishwasher door and press the power

button to turn on the appliance.

4. Press the Program button repeatedly to choose

the desired wash program. The programs will

cycle in the following order: Heavy -> Normal

-> ECO -> Glass -> Rapid -> Rinse

5. Press the Options button to select the desired

options.

6. Run the hot water faucet nearest the appliance

until the water is hot and then turn it off.

7. Press the Start/Pause button to begin the cycle.

Note: When a wash program is ﬁ nished the

appliance will buzz 8 times and END will appear

on the display screen.

ADDING A FORGOTTEN DISH

A forgotten dish can be added to a running cycle

any time before the detergent dispenser has

opened. If the detergent has already been released

into the appliance, it is recommended not to add

more dishes as they will not receive adequate

cleaning.

To add a dish:

1. Open door slightly and wait a few seconds

until the wash action stops before completely

opening.

2. Add the forgotten item.

3. Close the door and press the start button to

restart the cycle.

Caution: Wait until wash action completely stops

before opening the door. Hot water may splash out

of the dishwasher and can cause injury.

OPERATING INSTRUCTIONS

CLEANING

• After every wash, leave the door slightly open so

that moisture and odors are not trapped inside

the appliance.

• Only use a soft cloth and mild detergent to

clean the appliance. Never use solvents or

abrasive cleaning agents as this can damage the

appliance.

• To remove water spots from the interior of the

appliance, use a soft cloth dampened with a

small amount of vinegar.

• If the appliance will not be used for a long

period of time, it is recommended to run a

normal wash cycle with the dishwasher empty

and then leave the door open until the interior

of the appliance is completely dry. This will help

the door seals last longer and will help prevent

odors from forming inside the appliance.

• Clean the door seals with a damp sponge

regularly to prevent odors from food particles

that can become trapped in the door seal.

CARE & MAINTENANCE

FILTER SYSTEM

The ﬁ lter system removes food particles from

the wash water and traps them. It is highly

recommended to empty and clean the ﬁ lters after

every wash cycle.

To clean the ﬁ lter system:

1. Turn off the dishwasher. Turn the ﬁ lter and lift

upwards to remove the ﬁ lter system from the

appliance.

2. Rotate the ﬁ lter insert counterclockwise to

unfasten and then detach the ﬁ lter insert.

3. Rinse and clean the ﬁ lters with water and

replace them inside the appliance.

CARE & MAINTENANCE

SPRAY ARM

The spray arm can be removed from the appliance

by pulling gently upwards. Rinse the spray arm with

warm water to remove any debris that can clog the

nozzles. Replace the spray arm in the appliance by

pushing downward until it clicks into place. Ensure

that the spray arm movement is not impeded before

running another cycle.

ERROR CODES

E1: Water intake is restricted or water pressure is

too low.

E3: Malfunction of heating element

E4: Water overﬂ ow

If the appliance displays any error code, a power

reset may resolve the issue. Unplug the appliance,

wait approximately 5 minutes and then plug the unit

back in.

PROBLEM POSSIBLE CAUSE

No power • A fuse may be blown or the circuit breaker tripped

• Power surge

• Plug not fully inserted into the wall outlet

• Door not closed correctly

Water not drained from dishwasher • Kink in drain hose

• Filter clogged

• Drain pump malfunction

Detergent left in the dispenser • Dishes blocking dispenser from fully opening; unit may be

over loaded

Suds left in the appliance • Too much detergent or wrong kind of detergent

• Too much rinse aid

White ﬁ lm or cloudiness on dishes or

interior tub

• Hard water minerals

• Too much detergent

• Not enough rinse aid

Noise inside the tub while running • The spray arm is hitting an item in the basket

• An item has fallen out of the basket and is on the bottom of

the wash tub

Dishes are not clean • Dishes were loaded incorrectly

• The wash program was not powerful enough

• Not enough detergent

• Items are blocking the spray arm; unit may be over loaded

• Filter clogged

Dishes are not drying • Dishes were loaded incorrectly

• Too many dishes were loaded

• Not enough rinse aid

• Dishes removed too quickly

Danby Consumer Care: 1-800-263-2629

Hours of operation:

Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time

Friday 8:30 am - 4:00 pm Eastern Standard Time

Information in this manual is subject to change without notice.

TROUBLESHOOTING

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an authorized service

depot. Any appliance requiring service outside the limited boundaries of “In Home Service”, will be the consumer’s

responsibility to transport at their own expense to the original point of purchase or a service depot for repair. If the

appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center, it must

be delivered to the nearest authorized Danby Service Depot by the purchaser.

Transportation charges to and from the service location are not protected by this warranty and are the

responsibility of the purchaser.

During the ﬁrst twelve (12) months, any functional parts of this product found to be defective, will be repaired or

replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

First 12 months

To obtain service

Boundaries of

in-home service

LIMITED “IN HOME” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

In Home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

Bienvenue

Bienvenue à la famille Danby. Nous sommes ﬁ ers de la qualité de nos produits et nous croyons

en le service ﬁ able. Nous vous suggérons de lire ce manual d’utilisation avant de brancher

votre nouvel appareil car il contient des informations inportantes sur l’utilisation, la sécurité, le

dépannage et la maintenance, aﬁ n d’assurer la ﬁ abilité et la longévité de votre appareil.

Visitez www.Danby.com pour accéder aux outils d’autoservice, aux FAQ et bien plus encore. Pour

obtenir de l’aide supplémentaire, composez 1-800-263-2629.

Notez les informations ci-dessous; Vous aurez besoin de cette information pour obtenir un

service sous garantie.

Vous devez fournir le reçu d’achat original pour valider votre garantie et recevoir le service.

Numéro de modèle: _____________________________________________

Numéro de serie: _______________________________________________

Date d’achat: __________________________________________________

Besoin d’assistance?

Avant d’appeler pour service, voici quelques choses que vous pouvez faire pour nous

aider à mieux vous servir.

Lire ce manuel du propriétaire:

Il contient des instructions pour vous aider à utiliser et à maintenir votre appareil

correctement.

Si vous recevez un appareil endommagé:

Contactez immédiatement le revendeur ou l’entrepreneur qui vous a vendu l’appareil.

Gagnez du temps et de l’argent:

Avant d’appeler pour service, consultez la section de dépannage à la ﬁ n de ce manuel.

Cette section vous aidera à résoudre les problèmes courants pouvant survenir.

1-800-26- Danby

(1-800-263-2629)

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

GARDER CES INSTRUCTIONS!

EXIGENCES DE SÉCURITÉ

• Les enfants devraient être surveillés pour

s’assurer qu’ils ne jouent pas avec l’appareil.

• Ne pas tenir debout, assis ou appuyer sur

la porte ou le porte-vaisselle. Ne placez pas

d’objets lourds sur la porte lorsqu’il est ouvert.

• Ne pas toucher l’élément chauffant pendant ou

immédiatement après l’utilisation.

• Ne faites pas fonctionner l’appareil à moins

que tous les panneaux de l’enceinte ne soient

correctement installés.

• Ouvrez la porte avec précaution pendant le

fonctionnement, l’eau peut fuir. Procéder avec

prudence car l’eau peut être chaude.

• Ne pas laver les articles en plastique à moins

qu’ils soient marqués comme étant au lave-

vaisselle.

• Utilisez uniquement des additifs de détergence

et de rinçage conçus pour un lave-vaisselle

automatique.

• N’utilisez jamais de savon, détergent à lessive

ou détergent à la main dans le lave-vaisselle.

• Garder le détergent et le rinçage hors de la

portée des enfants.

• Vériﬁ ez que le distributeur de détergent est vide

après la ﬁ n du cycle de lavage.

• Les détergents de la lave-vaisselle sont fortement

alcalins et peuvent être extrêmement dangereux

en cas d’ingestion. Eviter le contact avec la peau

et les yeux.

• Retirez la porte de l’appareil en cas de

démontage ou de rejet.

• La pression maximale d’eau d’entrée autorisée

est de 0.04 - 1 Mpa.

• La température d’entrée d’alimentation en

eau doit être comprise entre 48 - 65°C (120 -

149°F).

INSTRUCTIONS DE MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas de

courtcircuit, la mise à la terre réduit les risques de

décharge électrique en fournissant un échappatoire

au courant électrique.

Cet appareil est équipé d’un cordon doté d’un

ﬁ l de mise à la terre et d’une prise de mise à la

terre. Le cordon d’alimentation doit être branché

sur une prise correctement mise à la terre. Si la

sortie est une prise murale à 2 broches, il est de

votre responsabilité de la remplacer par une prise

murale à 3 broches correctement mise à la terre. La

plaque signalétique en série indique la tension et la

fréquence auxquelles l’appareil est conçu.

AVERTISSEMENT - Une utilisation incorrecte de la

ﬁ che de mise à la terre peut entraîner un risque de

choc électrique. Consultez un électricien qualiﬁ é

ou un agent de service si les instructions de mise

à la terre ne sont pas complètement comprises, ou

s’il existe un doute quant à savoir si l’appareil est

correctement mis à la terre.

N’UTILISER JAMAIS DE FIL DE RALLONGE

Ne connectez pas votre appareil aux rallonges ou

avec un autre appareil dans la même prise murale.

Ne pas épisser le cordon d’alimentation. Ne coupez

ou retirez en aucun cas la troisième broche du

cordon d’alimentation.

Si le cordon d’alimentation est endommagé, il doit

être remplacé par le fabricant, son agent de service

ou une personne qualiﬁ ée similaire aﬁ n d’éviter tout

risque.

Assurez-vous que les composants sont remplacés

par des composants similaires et que l’entretien est

effectué par le personnel de maintenance autorisé

en usine pour minimiser le risque d’allumage

en raison de pièces incorrectes ou d’un service

incorrect.

Cet appareil n’est pas destiné à être utilisé par

des personnes (y compris des enfants) dont les

capacités physiques, sensorielles ou mentales

peuvent être différentes ou réduites, ou qui ont de

l’expérience ou des connaissances, à moins que

ces personnes ne soient surveillées ou formées

pour faire fonctionner l’appareil par une personne

responsable de leur sécurité.

INSTRUCTIONS D’INSTALLATION

ACCESSOIRES

1. Vis ST3.5*9 pour le support d’installation (x2)

2. Vis ST3.9*13 pour la plaque de protection (x2)

3. Vis ST4*14 pour l’accolade d’installation (x2)

4. Bande de condensation

5. Support d’installation (x2)

6. Bouchons de réglage (x2)

7. Plaque de protection

8. Serre-câble pour ﬁ xer le tuyau de vidange

ENCLOSURE

L’emplacement d’installation doit avoir un sol

solide capable de supporter l’appareil lorsqu’il

est complètement chargé et rempli d’eau.

L’emplacement doit être à moins de 3 mètres d’un

évier avec un accès facile à l’alimentation en eau,

au drain et à une prise électrique. L’emplacement

doit avoir sufﬁ samment d’espace devant pour que

la porte s’ouvre à 90° aﬁ n que le lave-vaisselle

puisse être chargé.

L’enceinte d’installation doit avoir les dimensions

suivantes: 23,6 pouces (60 cm) de largeur sur 32,5

pouces (82,5 cm) de hauteur sur 22,8 pouces (58

cm) de profondeur. Il doit y avoir moins de 5 mm

entre le haut du lave-vaisselle et le meuble et la

porte du lave-vaisselle doit être alignée avec la face

du meuble.

Si nécessaire, découpez des trous dans les armoires

environnantes pour accéder aux connexions d’eau

et d’alimentation.

INSTRUCTIONS DE RACCORDEMENT À L’EAU

La pression de la conduite d’alimentation en eau

chaude doit être comprise entre 0,04 et 1 MPa.

La température d’entrée d’alimentation en eau

doit être comprise entre 48 et 65°C (120 et

149°F). Assurez-vous que la température de

l’eau ne dépasse pas 65°C (149°F) pour éviter

d’endommager la vaisselle.

Assurez-vous que le disjoncteur et la vanne

d’alimentation en eau sont éteints avant de

raccorder la conduite d’alimentation en eau chaude

au lave-vaisselle.

Le câble d’alimentation se connecte à la boîte

de jonction sur le côté avant droit de l’appareil.

La conduite d’alimentation en eau chaude se

raccordera à l’oriﬁ ce d’eau sur le côté avant

gauche de l’appareil.

Remarque: Il est recommandé de n’utiliser que

de l’eau douce dans l’appareil pour obtenir les

meilleurs résultats de lavage.

90 r

23.6 inches

(60 cm)

90 r

32.5 inches

(82.5 cm)

22.8 inches

(58 cm)

Câble

d'alimentation

Ligne d'alimentation

en eau chaude

135 - 185 mm

(5 1/3 - 7 1/3”)

INSTRUCTIONS D’INSTALLATION

Connexion de la ligne d’eau chaude

Faites passer la ligne d’eau chaude dans le canal

sur le côté inférieur gauche de l’appareil. Assurez-

vous que la ligne d’eau chaude n’est pas tordue,

puis connectez-la à l’arrière de l’appareil en

utilisant un coude. Utilisez du ruban téﬂ on ou un

produit d’étanchéité sur la connexion pour éviter les

fuites.

Ne pas trop serrer le coude à 90°. Cela peut

endommager l’entrée d’eau et provoquer une fuite.

Connexion de la ligne de vidange

Le tuyau de vidange se raccordera à la pompe de

vidange située au bas de l’appareil. Exécutez la

ligne de vidange dans le même canal sur le fond de

l’appareil que la ligne d’eau chaude. Assurez-vous

qu’il n’y a rien à l’intérieur du tuyau de vidange

et qu’il ne se déchire pas pendant le processus

d’installation.

Il existe plusieurs façons de raccorder le tuyau

d’évacuation en fonction de la conﬁ guration de

l’évier. Passez en revue les différentes façons

de relier le système de vidange et choisissez la

méthode qui convient le mieux à l’application. Les

codes locaux peuvent nécessiter l’installation d’un

kit d’entrefer. Vériﬁ ez auprès d’un plombier qualiﬁ é

s’il y a un doute.

1. Espace d’air

2. Espace d’air avec élimination des déchets

3. Pas d’espace d’air

4. Pas d’espace d’air avec élimination des déchets

Utilisez un connecteur en caoutchouc pour

connecter les tuyaux de vidange et les colliers de

serrage sur tous les points de connexion.

Fixez le tuyau de vidange au mur de l’évier

en utilisant des colliers de serrage ou d’autres

matériaux de ﬁ xation. S’il n’est pas ﬁ xé, le tuyau de

vidange risque de se plier, entraînant des problèmes

de drainage.

Le diamètre interne du tuyau de vidange est de 21

mm (0,8 pouce).

Le haut du tuyau de vidange doit être à moins de

100 cm (39 pouces) du sol.

Si le tuyau de vidange n’est pas enroulé, l’eau peut

siphonner pendant un cycle de lavage.

Les coudes du tuyau de vidange doivent être

soutenus de sorte que le tuyau ne plie pas ou ne plie

pas.

INSTRUCTIONS D’INSTALLATION

INSTRUCTIONS DE CONNEXION DE CÂBLAGE

Avant de connecter le câble d’alimentation au lave-

vaisselle, assurez-vous que le disjoncteur est éteint.

Dans la boîte de jonction située à l’avant en bas

à droite du lave-vaisselle, trouvez les trois ﬁ ls

d’alimentation du lave-vaisselle, y compris la ligne

de mise à la terre.

Faites passer le câble d’alimentation à travers le

réducteur de tension, puis dans la boîte de jonction.

Connectez le ﬁ l noir du lave-vaisselle au ﬁ l noir du

câble d’alimentation en insérant les deux dans un

écrou de ﬁ l, puis en tournant le connecteur de ﬁ l.

Connectez le ﬁ l blanc au ﬁ l blanc et le vert au vert

de la même manière.

Revériﬁ ez chaque ﬁ l pour vous assurer qu’il est

connecté correctement et solidement.

Chaque ﬁ l coloré doit être connecté au ﬁ l

correspondant de la même couleur.

Le blanc doit être connecté au blanc, noir au noir et

vert au vert.

Replacez le couvercle de la boîte de jonction sur le

lave-vaisselle.

Revériﬁ ez chaque ﬁ l pour vous assurer qu’il est

connecté correctement et solidement. Chaque ﬁ l

coloré doit être connecté au ﬁ l correspondant de la

même couleur.

AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE

Pour éviter les chocs électriques, ne travaillez pas

sur un circuit sous tension. Cela pourrait entraîner

des blessures graves ou la mort. Pour éviter les

risques d’incendie, assurez-vous que les travaux

électriques sont correctement installés. Seuls les

électriciens qualiﬁ és doivent effectuer des travaux

électriques.

1. Boîte de dérivation

2. Câble d’alimentation

3. Noir à noir

4. Blanc à blanc

5. Vert à vert (terre à terre)

6. Soulagement des contraintes

La page est en cours de chargement...

Danby DDW2404EBSS Le manuel du propriétaire

Marque: Danby

Modèle: DDW2404EBSS

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

DDW2404EBSS

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DDW2404EBSS Owner's manual
español: Danby DDW2404EBSS El manual del propietario

Danby DDW2404EBSS Le manuel du propriétaire

Ce manuel convient également à

Danby DDW2404EBSS Le manuel du propriétaire

dans d''autres langues

Documents connexes