Ohaus SJX1502N/E Guide de démarrage rapide

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com i Scout

TM

SJX Balances

UNPACKING

Carefully remove your Scout balance and each of its components from the package.

Store the packaging material to ensure safe storage and future transport.

Included Components:

 Balance

 Pan

 Quick Start Guide

 Calibration Mass (only for SJX/E models with 64g capacity)

 Warranty Card

 Scoop (only for models with 64g capacity)

 AC Adapter & Plug

 Capacity label set (SJX323N/E and SJX1502N/E only)

SELECTING THE LOCATION

Place on a firm, steady surface with sufficient space. Avoid excessive air currents,

vibrations, heat sources, or rapid temperature changes.

PREPARATION FOR USE

Step-1

Release the red Transportation Lock on subplatform of the balance

Non SJXN/E models:

Turn the pointer 90 counter-clockwise.

SJXN/E models:

Turn the pointer 90 clockwise, then

remove the shipping lock by pulling it

out before installing the pan.

Store the shipping lock properly for

future transport. To reinstall it, follow

the removal process in reverse order.

Pointer pulled out:

Unlocked

Position

Locked

Position

Locked

Position

Unlocked

Position

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances ii Corporation www.ohaus.com

Step-2

Install the Pan

For SJX/E:

Rectangular pan: Place diagonally on

sub-platform and rotate counter-

clockwise until it locks.

Round pan: Set straight down on

subplatform.

For SJX: Install the stainless steel pan

directly on the subplatform.

Step-3

Attach Capacity Label

For SJX323N/E and SJX1502N/E:

Attach the capacity label above the

screen at the position as demonstrated

in the graphic, and align the edges with

the dotted lines.

Step-4

Connect Power

Connect the AC Adapter to the balance

input jack.

Battery Installation

Install the Four “AA” (LR6) batteries

(not included) with polarity as shown in

the battery compartment.

Step-5

Level the balance

Level the balance before using by

adjusting the feet until the air bubble is

centered

AC Adapter Jack

Battery

Compartment

For SJX/E

For SJX323N/E

and SJX1502N/E

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com iii Scout

TM

SJX Balances

SAFETY PRECAUTIONS

CAUTION: Read all safety warnings before installing, making connections, or

servicing this equipment. Failure to comply with these warnings could result in

personal injury and/or property damage. Retain all instructions for future reference.

 Verify that the local AC power supply voltage is within the input voltage

range printed on the AC adapter’s ratings label.

 Only connect the AC adapter to a compatible grounded socket.

 Position the instrument such that the AC adapter can be easily

disconnected from the socket.

 Position the power cord so that it does not pose a potential obstacle or

tripping hazard.

 Operate the equipment only under ambient conditions specified in the user

instructions.

 This equipment is intended for indoor use and should only be operated in

dry locations.

 Do not operate the equipment in hazardous or explosive environments.

 Disconnect the equipment from mains power before cleaning or servicing.

 Service should only be performed by authorized personnel.

Intended Use

This instrument is intended for use in laboratories, schools, businesses and light

industry. It must only be used for measuring the parameters described in these

operating instructions. Any other type of use and operation beyond the limits of

technical specifications, without written consent from OHAUS, is considered as not

intended. This instrument complies with current industry standards and the

recognized safety regulations; however, it can constitute a hazard in use. If the

instrument is not used according to these operating instructions, the intended

protection provided by the instrument may be impaired.

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances iv Corporation www.ohaus.com

CONTROLS



Button Functions

Button

Short

Press

Zero/On

Turns the balance

on;

If balance is On,

sets Zero

Print

Initiates print

Function

Initiates an

application mode

Tare

Long

Press

Extended

Press

Off

Turns the balance

Off

None

Units

Changes the

weighing unit

None

Mode

Changes the

application mode

None

Menu

Enters the user

menu

View the preset

Tare value

Short

Press

(Menu

Function)

Yes

Accepts the current

setting

No

Advances to the

next menu or

setting

Back

Moves to previous

menu item

Exit

Exits the user menu

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com v Scout

TM

SJX Balances

CALIBRATION

When the balance is operated for the first time, a calibration is recommended to

ensure accurate weighing results.



External Span Calibration

With balance turned on:

Step-1

Press and hold Menu until [mMeNU] (Menu) is displayed.

Step-2

Release the button, the display will show [C.A.L].

Step-3

Press Yes to accept. [SpaN] will then be shown.

Step-4

Press Yes to begin the span calibration. [--C--] will blink and the

Zero reading is stored automatically.

Step-5

The specified mass blinks on the display.

Place the specified span calibration mass on the pan or press

No to select an alternate weight.

[--C--] will blink while the reading is stored.

The display will show [done] if the calibration was successful. The

balance returns to the previous application mode and is ready for

use.



Internal Calibration (not available for SJX/E models)

With balance turned on:

Step-1

Press and hold Menu until [mMeNU] (Menu) is displayed.

Step-2

Release the button, the display will show [C.A.L].

Step-3

Press Yes to accept. [In.CAL] will then be shown.

Step-4

Press Yes to begin the Internal calibration. Zero reading is

stored automatically.

Step-5

Pull the InCal handle while the

display show [PULL].

Step-6

Push the InCal handle while the

display show [PUSH].

Step-7

Repeat the step-5, and step-6 one

more time.

Step-8

The display will show [done] if the calibration was successful.

The balance returns to the previous application mode and is

ready for use.

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances vi Corporation www.ohaus.com

OPERATION & APPLICATIONS

The balance can be configured to operate in one or more Application modes.

Press and hold Mode key to select your Application mode.

The Scout SJX balance incorporates the following Applications:

[wWeIGH]

[Count]

[Percnt]

[CHeCK]

[total]

[SPEC.Gr]

[Hold]

Weighing

Parts

Counting

Percent

Weighing

Check

Weighing

Totalization

Density

Determination

Display

Hold



Weighing

Step-1

Press the Zero/On button to turn the balance on.

Step-2

Select Weighing (default application) by pressing & holding

Mode key.

Step-3

Press Tare or Zero if necessary to begin.

Step-4

Place objects on the pan to display the weight. When stable, the

* appears on the display. The display then shows the resulting

weight of the sample.

MENU STRUCTURE

Sub-Menus

C.a.l**

S.E.t.U.P

M.o.d.E

U.n.i.t**

E.n.d

User Menu Items:

In.CAL*

CAL.Adj*

-100

..

0

..

100

Span

Lin

Reset

Yes/No

Auxiliary

Graduation**

On/Off

Filter

Low/Med/High

AZT

0.5/1/3/Off

StableRange

0.5/1/2//5

Backlight

Off/On/Auto

Auto Tare

Off/On/On-acc

Auto Off

Off/1/5/10

Reset

Yes/No

Weighing

On/Off

Counting

On/Off

Percent

On/Off

Check

On/Off

Totalize

On/Off

Density

On/Off

Hold

Disp/Peak/Off

Reset

g

kg

ct

oz

ozt

dwt

lb

grn

hkt

sgt

twt

t

tola/tical

End

Note: Bold fonts are default settings in the menus.

* These sub-menus are not available in SJX/E models.

** Available Settings may vary by local regulations.

No/Back

Long press –

Enter menu

Short press -

Accept

Short press –

Go Next/Prev.

menu

Yes

Exit

Short press –

Exit menu

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com vii Scout

TM

SJX Balances

ADDITIONAL FEATURES



Connecting the Interface

Use an optional interface connectivity

kit to connect the balance either to a

computer, printer or OHAUS auxiliary

display.

Below Interface kit accessories are

available:

RS232, USB Host, USB Device,

Ethernet, Bluetooth

*

.

Interface connection on the rear of the

balance:

* Interface kits may vary according to local regulations



Weigh Below Hook

The weigh below hook on SJX/E models is located at the reverse

side of the battery cover as shown below (on SJX models it is located in

the weigh below protective cover). To use this feature, remove the red

protective cover underneath for the weigh below opening.

MAINTENANCE

Cleaning

WARNING: Electric Shock Hazard. Disconnect the equipment from the

power supply before cleaning.

The housing may be cleaned with a cloth dampened with a mild detergent if necessary.

Attention: Do not use solvents, chemicals, alcohol, ammonia or abrasives to

clean the housing or control panel.

Interface connection

AC Adapter Jack

Security slot

Weigh below protective cover

Weigh below

hook

(SJX/E)

0

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances viii Corporation www.ohaus.com

Troubleshooting

The following table lists common problems and possible causes and remedies.

If the problem persists, contact OHAUS or your authorized dealer.

Symptom

Possible Cause

Cannot turn on

No power to balance

Poor accuracy

Improper calibration

Unstable environment

Cannot calibrate

Security switch in locked position

Err 8.1

Weight exceeds power on zero range.

Err 8.2

Weight below power on zero range.

Err 8.3

Over load (weight exceeds rated capacity)

Err 8.4

Under load (pan removed)

Err 8.5

Tare out of range

Err 8.6

Displayed value exceeds 999999 (possible in Totalization

mode)

Err 8.7

Unknown internal weight position

ref.err

Parts counting or percentage error – sample weight <1d.

Balance shows error then exits parts counting or goes to

[Clr.APU].

Lo.ref

Percent Reference weight or APW is too low for accurate

results

CAL E

Fail to do calibration.

USB.Err

Cannot find menu or app file in U-disk.

Service Information

If the troubleshooting section does not resolve or describe your problem, contact

your authorized OHAUS service agent. For service assistance or technical support

in the United States call toll-free 1-800-672-7722 ext. 7852 between 8:00 AM and

5:00 PM EST. An OHAUS product service specialist will be available to provide

assistance. Outside the USA, please visit our web site, www.ohaus.com to locate

the OHAUS office nearest you.

Accessories

DESCRIPTION

Item Number

DESCRIPTION

Item Number

RS232 kit

30268982

Stacking Kit, x1

30268988

USB Host kit

30268983

Specific Gravity kit

30269020

USB Device Kit

30268984

Auxiliary Display Kit

30269019

Bluetooth Kit*

30268985

Carrying Case

30269021

Ethernet Kit

30268986

In-Use Cover

30269022

Stacking Kit, x6

30268987

Printers and Cables

Contact

OHAUS

Note: * Bluetooth kit is only available in certain regions according to the local

regulations.

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com ix Scout

TM

SJX Balances

LEGAL FOR TRADE (SJX...N/E models only)

When the balance is used in trade or a legally controlled application it must be set

up, verified and sealed in accordance with local weights and measures regulations.

It is the responsibility of the purchaser to ensure that all pertinent legal requirements

are met. As the requirements vary by jurisdiction, the purchaser is advised to

contact their local weights and measures office for instructions about putting the

balance into service.

Settings

Before verification and sealing, perform the following steps:

1. Verify that the menu settings meet the local weights and measures

regulations.

2. Units menu should be reviewed. Verify the units turned On are

permitted by the local weights and measures regulations.

3. Perform a calibration.

4. Set the position of the Security Switch to the locked position.

Verification

A weights and measures official must perform the verification procedure. Contact

the local weights and measures office for more information.

Sealing

After the Balance has been verified, it must be sealed by the weights and measures

official to prevent undetected access to the legally controlled settings. Before

sealing the device, ensure that the security switch is in the Locked position.

If using a wire seal, pass the sealing wire through the holes in the security switch

and Bottom Housing as shown.

If using a paper seal, place the seal over the security switch and Bottom Housing as

shown.

Unlocked

Locked with Paper Seal

Locked with Wire Seal

TECHNICAL DATA

Equipment Ratings:

Altitude: Up to 2000 m

Indoor use only

Operating temperature range: +5 °C to +40 °C

Specified temperature range: Refer to tables below

Relative humidity: 10% to 80% at 31°C , decreasing linearly to 50% at 40°C, non-

condensing

Power: AC power adaptor input 100-240V 50/60 Hz and output 5 V DC 1 A (For

use with certified or approved power supply, which must have a SELV and limited

energy circuit output.), or 4 AA batteries

Main supply voltage fluctuations: up to ± 10% of the nominal voltage

Pollution degree: 2

Installation category: II

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances x Corporation www.ohaus.com

General Models

Model

SJX323

/

SJX622

SJX1502

SJX323/E

SJX322/E

SJX622/E

SJX1502/E

Capacity

320 ct (64 g)

320 g

620 g

1500 g

Readability

0.005 ct (0.001 g)

0.01 g

Repeatability (Std. Dev.)

0.002 g

0.01 g

0.02 g

Linearity

0.003 g

0.01 g

0.02 g

0.03 g

Span Calibration Mass*

50 g

200 g

300 g

1.5 kg

Linearity Calibration Mass

30, 60 g

200, 300 g

300, 600 g

1 kg, 1.5 kg

Capacity x Readability (kg)

/

1.5 x 0.00001

Capacity x Readability (ct)

320 x 0.005

1600 x 0.05

3100 x 0.05

7500 x 0.05

Capacity x Readability (oz)

2.25750 x 0.00005

11.2880 x 0.0005

21.8700 x 0.0005

52.9110 x 0.0005

Capacity x Readability (ozt)

2.05765 x 0.00005

10.2880 x 0.0005

19.9335 x 0.0005

48.2260 x 0.0005

Capacity x Readability (dwt)

41.153 x 0.001

205.76 x 0.01

398.67 x 0.01

964.52 x 0.01

Capacity x Readability (lb)

/

1.36690 x 0.00005

3.30690 x 0.00005

Capacity x Readability (grn)

987.66 x 0.02

4938.4 x 0.2

9568.0 x 0.2

23148.4 x 0.2

Stabilization Time (s)

1.5

1

1.5

Construction

ABS plastic housing with 304 stainless steel (SST) pan

Draftshield

Yes

No

Calibration

SJX/E: User-selectable external span or linearity calibration

SJX: Manual Internal Calibration / User-selectable external span or linearity calibration

Tare Range

Full Capacity by subtraction

Weighing Units**

g, kg, ct, oz, ozt, dwt, lb, grn, hkt, sgt, twt, tical, tola

Application Modes**

Weighing, Parts Counting, Percent Weighing, Check Weighing, Totalization, Density

Determination, Display Hold

Typical Battery Life

80 hours

Specified Temperature

Range

10° C (50° F) to 40° C (104° F)

Storage Conditions

-20° C (-4° F) to 55° C (131° F) at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth*** (all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

20 mm digits / 0.78 in

Pan Size (W x D)

Ø 93 mm / 3.7 in

Ø 120 mm / 4.7 in

170 x 140 mm / 6.7

x 5.5 in

Scale Dimensions - SJX/E

(W x D x H)

202 x 222 x 103 mm /

8 x 8.7 x 4.1 in

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Scale Dimensions - SJX

(W x D x H)

202 x 230 x 114 mm

202 x 230 x 68 mm

Shipping Dimensions -

SJX/E (W x D x H)

300 x 250 x 129mm /

11.8 x 9.8 x 5.1 in

300 x 250 x 86 mm / 11.8 x 9.8 x 3.4 in

Shipping Dimensions - SJX

(W x D x H)

300 x 250 x 129mm

Net Weight (SJX/E)

1 kg / 2.2 lb

Net Weight (SJX)

1.1 kg

1.6 kg

Shipping Weight (SJX/E)

1.5 kg / 3.3 lb

Shipping Weight (SJX)

1.7 kg

2.2 kg

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com xi Scout

TM

SJX Balances

Model

/

SJX6201

/

SJX621/E

SJX3201/E

SJX6201/E

SJX8200/E

Capacity

620 g

3200 g

6200 g

8200 g

Readability

0.1 g

1 g

Repeatability (Std. Dev.)

0.1 g

1 g

Linearity

0.1 g

0.2 g

1 g

Span Calibration Mass*

300 g

3 kg

5 kg

8 kg

Linearity Calibration Mass

300, 600 g

1.5 kg, 3 kg

3 kg, 6 kg

4 kg, 8 kg

Capacity x Readability (kg)

/

3.2 x 0.0001

6.2 x 0.0001

8.2 x 0.001

Capacity x Readability (ct)

3100 x 0.5

16000 x 0.5

31000 x 0.5

41000 x 5

Capacity x Readability (oz)

21.870 x 0.005

112.880 x 0.005

218.700 x 0.005

289.25 x 0.05

Capacity x Readability (ozt)

19.930 x 0.005

102.880 x 0.005

199.335 x 0.005

263.60 x 0.05

Capacity x Readability (dwt)

398.7 x 0.1

2057.6 x 0.1

3986.7 x 0.1

5270 x 1

Capacity x Readability (lb)

1.3670 x 0.0005

7.0550 x 0.0005

13.6685 x 0.0005

18.080 x 0.005

Capacity x Readability (grn)

9570 x 2

49380 x 2

95680 x 2

126540 x 20

Stabilization Time (s)

1

Construction

ABS plastic housing with 304 stainless steel (SST) pan

Draftshield

No

Calibration

SJX/E: User-selectable external span or linearity calibration

SJX: Manual Internal Calibration / User-selectable external span or linearity calibration

Tare Range

Full Capacity by subtraction

Weighing Units**

g, kg, ct, oz, ozt, dwt, lb, grn, hkt, sgt, twt, tical, tola

Application Modes**

Weighing, Parts Counting, Percent Weighing, Check Weighing, Totalization, Density

Determination, Display Hold

Typical Battery Life

120 hours

80 hours

120 hours

Specified Temperature

Range

10° C (50° F) to 40° C (104° F)

Storage Conditions

-20° C (-4° F) to 55° C (131° F) at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth*** (all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

20 mm digits / 0.78 in

Pan Size (W x D)

170 x 140 mm / 6.7 x 5.5 in

Scale Dimensions - SJX/E

(W x D x H)

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Scale Dimensions - SJX

(W x D x H)

202 x 230 x 68 mm

Shipping Dimensions -

SJX/E

(W x D x H)

300 x 250 x 86 mm / 11.8 x 9.8 x 3.4 in

Shipping Dimensions - SJX

(W x D x H)

300 x 250 x 129mm

Net Weight (SJX/E)

1 kg / 2.2 lb

Net Weight (SJX)

1.6 kg

Shipping Weight (SJX/E)

1.5 kg / 3.3 lb

Shipping Weight (SJX)

2.2 kg

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances xii Corporation www.ohaus.com

NTEP and Measurement Canada Approved models

Model

SJX323N/E

SJX622N/E

SJX1502N/E

SJX6201N/E

Capacity

320 ct (64 g)

620 g

1500 g

6200 g

Readability

0.01 ct (0.001 g)

or 0.1 ct (0.01 g)

0.1 g

0.01 g or 0.1 g

1 g

Verification Interval e

0.1 ct (0.01 g)

0.1 g

1 g

Class

II

III

II

III

Span Calibration Mass*

50 g

300 g

1.5 kg

5 kg

Linearity Calibration Mass

30, 60 g

300, 600 g

1 kg, 1.5 kg

3 kg, 6 kg

Capacity x Readability (kg)

/

1.5 x 0.00001 or

1.5 x 0.0001

6.2 x 0.001

Capacity x Readability (ct)

320 x 0.01 or 320

x 0.1

3100 x 0.5

7500 x 0.5

31000 x 5

Capacity x Readability (oz)

2.2575 x 0.0005

21.870 x 0.005

52.910 x 0.005

218.70 x 0.05

Capacity x Readability (ozt)

2.0575 x 0.0005

19.935 x 0.005

48.225 x 0.005

199.35 x 0.05

Capacity x Readability (dwt)

41.153 x 0.001 or

41.15 x 0.01

398.7 x 0.1

964.52 x 0.01 or

964.5 x 0.1

3987 x 1

Capacity x Readability (lb)

/

1.3670 x 0.0005

3.3070 x 0.0005

13.670 x 0.005

Capacity x Readability (grn)

987.6 x 0.2

9568 x 2

23148 x 2

95680 x 20

Stabilization Time (s)

1.5

1

1.5

1

Construction

ABS housing & Stainless steel pan

Draftshield

Yes

No

Calibration

User-selectable external span or linearity calibration

Tare Range

Full Capacity by subtraction

Weighing Units**

g, kg, ct, oz, ozt, dwt, lb, grn

Application Modes**

Weighing, Parts Counting, Percent Weighing, Check Weighing, Totalization, Density

Determination, Display Hold

Typical Battery Life

80 hours

Specified Temperature

Range

Class II: 10° C (50° F) to 30° C (86° F)

Class III: 10° C (50° F) to 40° C (104° F)

Storage Conditions

-20° C (-4° F) to 55° C (131° F) at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth*** (all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

0.78 in / 20 mm digits

Pan Size (W x D)

Ø 93 mm / 3.7 in

Ø 120 mm / 4.7 in

170 x 140 mm / 6.7 x 5.5 in

Scale Dimensions

(W x D x H)

202 x 222 x 103

mm /

8 x 8.7 x 4.1 in

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Shipping Dimensions

(W x D x H)

300 x 250 x

129mm / 11.8 x

9.8 x 5.1 in

300 x 250 x 86 mm / 11.8 x 9.8 x 3.4 in

Net Weight

2.2 lb / 1 kg

Shipping Weight

3.3 lb / 1.5 kg

Quick Start Guide Scout

TM

SJX Balances

Ohaus Corporation www.ohaus.com xiii Scout

TM

SJX Balances

COMPLIANCE

Compliance to the following standards is indicated by the corresponding mark on

the product.

Mark

Standard

This product complies with the EU Directives 2011/65/EU (RoHS),

2014/30/EU (EMC), 2014/35/EU (LVD) and 2014/31/EU (NAWI). The

EU Declaration of Conformity is available online at

www.ohaus.com/ce.

This product complies with the EU Directive 2012/19/EU (WEEE) and

2006/66/EC (Batteries). Please dispose of this product in accordance

with local regulations at the collecting point specified for electrical and

electronic equipment. For disposal instructions in Europe, refer to

www.ohaus.com/weee.

AS/NZS 61000.6.1, AS/NZS 61000.6.3

CAN/CSA-C22.2 No. 61010-1

UL Std. No. 61010-1

FCC Compliance Statement:

Note:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

ISED Canada Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Scout

TM

SJX Balances Quick Start Guide

Scout

TM

SJX Balances xiv Corporation www.ohaus.com

INSTRUCTION MANUAL

For more detailed information about the balance,

please refer to the product instruction manual. The

instruction manual can be obtained either by

scanning the QR code or by going to the Scout SJX

product page to download it.

Go to www.ohaus.com to register your product's

warranty.

Product Page:

http://www.ohaus.com

QR Code:

Guía de inicio rápido Balanzas Scout

TM

SJX

Ohaus Corporation www.ohaus.com i Balanzas Scout

TM

SJX

DESEMBALAJE

Retire cuidadosamente del embalaje la balanza Scout y cada uno de sus

componentes. Guarde el material de embalaje en un lugar seguro para transportar

la balanza posteriormente.

Componentes incluidos:

 Balanza

 Masa de calibración (solo para modelos SJX/E de 64 g

de capacidad)

 Guía de inicio rápido

 Cuchara (solo para modelos de 64 g de capacidad)

 Tarjeta de garantía

 Adaptador de CA y enchufe

 Plato

 Conjunto de etiquetas de capacidad (solo SJX323N / E

y SJX1502N / E)

SELECCIÓN DEL LUGAR DE INSTALACIÓN

Coloque la balanza sobre una superficie firme y con suficiente espacio. Evite el

exceso de corrientes de aire, vibraciones, fuentes de calor o cambios bruscos de

temperatura.

PREPARACIÓN PARA EL USO

Paso 1

Libere el bloqueo de transporte de color rojo ubicado en la sub-

plataforma de la balanza

Modelos no SJXN/E:

Gire el puntero 90 en sentido antihorari.

Modelos SJXN/E:

Gire el puntero 90 en sentido horari.

Eliminado el bloqueo de transporte

tirando de él antes de instalar la bandeja.

Almacenar el bloqueo de transporte

adecuada para el transporte futuro. Para

volver a instalarlo, siga el proceso de

extracción en orden inverso.

Puntero sacó:

Posición de

bloqueo

Posición de

desbloqueo

Posición de

bloqueo

Posición de

desbloqueo

Balanzas Scout

TM

SJX Guía de inicio rápido

Balanzas Scout

TM

SJX ii Ohaus Corporation www.ohaus.com

Paso 2

Instale el plato

Para el modelo SJX/E:

Plato rectangular: Coloque el plato

diagonalmente sobre la sub-plataforma y

gire en sentido antihorario hasta que

encaje.

Plato redondo: Colóquelo derecho hacia

abajo sobre la sub-plataforma.

Para el modelo SJX: Instale el plato de

acero inoxidable directamente sobre la

sub plataforma.

Paso 3

Adjuntar etiqueta de capacidad

Para SJX323N / E y SJX1502N / E:

Pegue la etiqueta de capacidad sobre el

pantalla en la posición como se demostró

en el gráfico y alinee los bordes con

Las líneas punteadas.

Para SJX323N / E y SJX1502N / E

Paso 4

Conecte la alimentación

Conecte el adaptador de CA al conector

de entrada de la balanza.

Instalación de las baterías

Instale las cuatro baterías "AA" (LR6, no

incluidas) con la polaridad que se indica

en el compartimento de baterías.

Paso 5

Nivele la balanza

Nivele la balanza antes del uso ajustando

las patas hasta que la burbuja de aire

esté centrada

Conector de entrada de

adaptador de CA

Compartimento

de baterías

Para el modelo

SJX/E

Guía de inicio rápido Balanzas Scout

TM

SJX

Ohaus Corporation www.ohaus.com iii Balanzas Scout

TM

SJX

PRECAUCIONES DE SEGURIDAD

PRECAUCIÓN: Lea todas las advertencias de seguridad antes de instalar, hacer

conexiones o efectuar reparaciones en este equipo. El incumplimiento de estas

advertencias puede causar lesiones personales y/o daños a la propiedad. Conserve

todas las instrucciones para referencia futura.

 Compruebe que el voltaje de la alimentación de CA local esté dentro del rango de

entrada impreso en la etiqueta de especificaciones del adaptador de CA.

 Solo conecte el adaptador de CA a una toma compatible con conexión de tierra.

 Posicione el instrumento de tal forma que el adaptador de CA se pueda

desconectar fácilmente de la toma de alimentación.

 Posicione el cable de alimentación de manera que no obstaculice el tránsito de

las personas o cree un peligro de tropiezos.

 Utilice el equipo solo bajo las condiciones ambientales especificadas en las

instrucciones del usuario.

 Este equipo está diseñado para uso en interiores y solo debe utilizarse en lugares

secos

 No opere el equipo en entornos peligrosos o explosivos.

 Desconecte el equipo de la red eléctrica antes de realizar una limpieza o un

mantenimiento.

 La reparación del equipo solo debe ser realizada por personal autorizado.

Uso previsto

Este instrumento está diseñado para su uso en laboratorios, escuelas, empresas e

industria ligera. Solo debe usarse para medir los parámetros descritos en estas

instrucciones de funcionamiento. Cualquier otro tipo de uso y operación más allá de

los límites de las especificaciones técnicas, sin el consentimiento por escrito de

OHAUS, se considera no previsto.

Este instrumento cumple con los estándares actuales de la industria y las normas

de seguridad reconocidas; sin embargo, puede constituir un peligro en uso.

Si el instrumento no se utiliza de acuerdo con estas instrucciones de

funcionamiento, la protección prevista proporcionado por el instrumento puede

verse afectado.

Balanzas Scout

TM

SJX Guía de inicio rápido

Balanzas Scout

TM

SJX iv Ohaus Corporation www.ohaus.com

CONTROLES



Funciones de los botones

Botón

Pulsación

breve

Zero/On

Enciende la

balanza;

Si la balanza está

encendida, ajusta

el cero

Print

Inicia la impresió n

Function

Inicia un modo de

aplicació n

Tare

Tara

Pulsación

larga

Pulsación

extendida

Off

Apaga la balanza

Ninguna

Units

Cambia la unidad

de pesaje

Ninguna

Mode

Cambia el modo de

aplicació n

Ninguna

Menu

Entra al menú de

usuario

Ver el valor de tara

predeterminado

Pulsación

breve

Menú

Funció n

Yes

Acepta el valor

actual

No

Avanza al siguiente

menú o ajuste

Back

Va al elemento de

menú anterior

Exit

Sale del menú de

usuario

Guía de inicio rápido Balanzas Scout

TM

SJX

Ohaus Corporation www.ohaus.com v Balanzas Scout

TM

SJX

CALIBRACIÓN

Cuando la balanza se opera por primera vez, se recomienda una calibración para

garantizar la precisión de los resultados de pesaje.



Calibración externa de rango

Con la balanza encendida:

Paso 1

Presione y mantenga presionado Menu hasta que aparezca

[mMeNU] (Menu).

Paso 2

Suelte el botón, la pantalla mostrará [C.A.L].

Paso 3

Pulse Yes para aceptar. [SpaN] se mostrará a continuación.

Paso 4

Pulse Yes para comenzar la calibración de rango. Mostrará

[--C--], la lectura de cero se guarda automáticamente.

Paso 5

Coloque la masa especificada de calibración de rango en el plato.

Pulse No para seleccionar un peso alternativo.

Se mostrará [--C--] mientras la lectura se guarda.

La pantalla mostrará [done] si la calibración se ha realizado con

éxito. La balanza vuelve al modo de aplicación anterior y está lista

para su uso.



Calibración interna (no disponible en los modelos SJX/E)

Con la balanza encendida:

Paso 1

Presione y mantenga presionado Menu hasta que aparezca

[mMeNU] (Menu).

Paso 2

Suelte el botón, la pantalla mostrará [C.A.L].

Paso 3

Pulse Yes para aceptar. [In.CAL] se mostrará a continuación.

Paso 4

Pulse Yes para comenzar la calibración de rango. La lectura de

cero se guarda automáticamente.

Paso 5

Tire de la manija InCal mientras la

pantalla muestra [PULL].

Paso 6

Empuje la manija InCal mientras la

pantalla muestra [PUSH].

Paso 7

Repita los pasos 5 y 6 una vez más.

Paso 8

La pantalla mostrará [done] si la calibración se ha realizado con

éxito. La balanza vuelve al modo de aplicación anterior y está lista

para su uso.

Balanzas Scout

TM

SJX Guía de inicio rápido

Balanzas Scout

TM

SJX vi Ohaus Corporation www.ohaus.com

OPERACIÓN Y APLICACIONES

La balanza puede configurarse para operar en uno o más modos de aplicación.

Presione y mantenga presionada la tecla Mode para seleccionar el modo de

aplicación. La balanza Scout SJX incorpora las siguientes aplicaciones:

[wWeIGH]

[Count]

[Percnt]

[CHeCK]

[total]

[SPEC.Gr]

[Hold]

Pesaje

Recuento de

piezas

Pesaje en

porcentaje

Pesaje de

comprobación

Totalización

Determinación

de densidad

Retención

de valor

en display



Pesaje

Paso 1

Pulse el botón Zero/On para encender la balanza.

Paso 2

Seleccione la aplicación de pesaje (aplicación predeterminada)

pulsando y manteniendo presionada la tecla Mode.

Paso 3

Si fuera necesario, pulse Tare o Zero para comenzar.

Paso 4

Coloque objetos sobre el plato para ver el peso. Cuando la medición

está estable, aparece * en la pantalla. La pantalla muestra a

continuación el peso resultante de la muestra.

ESTRUCTURA DEL MENÚ

Elementos de

menú de usuario:

C.a.l**

S.E.t.U.P

M.o.d.E

U.n.i.t**

E.n.d

User Menu Items:

In.CAL*

CAL.Adj*

-100

..

0

..

100

Span

Lin

Reset

Yes/No

Auxiliar

Graduación**

On/Off

Filter

Low/Med/High

AZT

0.5/1/3/Off

StableRange

0.5/1/2//5

Backlight

Off/On/Auto

Auto Tare

Off/On/On-acc

Auto Off

Off/1/5/10

Reset

Yes/No

Weighing

On/Off

Counting

On/Off

Percent

On/Off

Check

On/Off

Totalize

On/Off

Density

On/Off

Hold

Disp/Peak/Off

Reset

g

kg

ct

oz

ozt

dwt

lb

grn

hkt

sgt

twt

t

tola/tical

End

Nota: Las letras en negrita son los valores predeterminados en los menús.

* Estos sub-menús no están disponibles en los modelos SJX/E.

** Las Configuraciónes disponibles pueden variar de acuerdo con los reglamentos

locales.

Pulsación larga:

Entrar a menú

Pulsación breve:

Aceptar

Pulsación breve:

Ir al menú

Next/Prev.

Pulsación breve:

Salir del menú

No/Back

Yes

Exit

La page charge ...

Ohaus SJX1502N/E Guide de démarrage rapide

Ce manuel convient également à

Ohaus SJX1502N/E Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents