Aosom 370-165V80GN Assembly Instructions

ASSEMBLY INSTRUCTION

IN221000459V03_US_CA

370-165V80

CHILDREN’S

ELECTRONIC MOTORCYCLE

• Suitable for 3+ Years

• Maximum user weight: 30 kg

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

Read and understand this entire manual before using!

Please keep this manual for future reference as it contains important

information. Before ﬁrst time use, charge the battery for at least 4-6

hours, but no more than 10hours.

WARNING: Must be assembled by an adult.

EN

On the purchase of your new Ride-On.

This ride-on car will provide your child with many miles of riding of enjoyment. To help

assure you and your rider a safe ride we ask you to please read this manual carefully, and

keep it for future reference.

Follow the recommendations in this manual, they are designed to improve the safety and

operation of your ride-on car and its rider.

Suitable age:

Charge time:

Load capacity:

Size of car:

About Your New Vehicle

3+ Years

8-12 hours

Under 30 kg

1065×515×680MM

Specification

●Non-rechargeable batteries are not to be recharged.

●If removable rechargeable batteries are used, the are only to be charged under adult

supervision.

●Remove rechargeable batteries from the product before charging.

●Do not mix old and new batteries. Do not mix different types of batteries: alkaline, standard

(carbon-zinc) or rechargeable (nickel-cadmium).

●Insert batteries as indicated inside the battery compartment, anode to anode, cathode to

cathode.

●Remove batteries during long periods of non-use. Always remove exhausted batteries from the

product. Battery leakage and corrosion can damage this product. Dispose of batteries safely.

●Never short circuit the battery terminals.

BATTERY INFORMATION

Battery

Charger

input

Motor

Speed

12V4.5AH X1

12V500mA

12V390-16000

3.8-5.8 km/h

Depend on local voltage

1

Parts List 2

Assembly tools required (not included):

Screwdriver

16

Front fender

pre-installed

6 pcs pre-installed

pre-installed

14

9

1

2

7

6

12

8

15

15 6

11

13

8

6

63

4

10

5

6

10

16

Parts Diagram 3

8

WARNING:

• CHOKING HAZARD! Not suitable for children under 36 months.

• Must be assembled by an adult.

PREVENT INJURIES AND DEATHS:

• NEVER LEAVE CHILD UNATTENDED. ADULT DIRECT SUPERVISION IS REQUIRED. Always keep child

in view when child is in vehicle.

Rules for Safe Riding

• To reduce the risk of injury, adult supervision is required. Never use in roadways, near

motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of

water, always wear shoes, and never allow more than 1 rider.

• Use the toy only on flat surfaces. Such as inside your house, garden or playground.

• Never use in the dark. A child could encounter unexpected obstacles and have an accident.

Operate the vehicle only in the daytime or a well-lit area.

• It is prohibited to change the circuit or add other electric parts

• Inspect wires and connections of the vehicle periodically.

• Do not let any child touch the wheels or be near them when the car is moving .

• This toy should be used with caution since skill is required to avoid falls or collisions

causing injury to the user or third parties.

• Protective equipment should be worn.

• Never use in roadways, near cars, or on near steep inclines or steps, swimming pools or

other bodies of water.

• Always wear shoes, always sit on the seat.

• Not to be used in traffic.

• This toy is unsuitable for children under 36 months due to its maximum speed; Maximum

user weight is 30 kg.

• This toy has no brake.

Safety 4

2

3

1

Attach the Rear Shock Absorber

1. Rotate the rear wheel frame until the bolt of the rear shock absorber is inserted into

the hole on the rear wheel frame.

2. Turn the vehicle body on its side. Slide a Ø8 washer onto the front axle.

3. Tighten a lock nut to the end of the bolt with a spanner.

5

Rear bottom View

4

1

23

5

Attach the Side Wheels & Front Fender

1. Fit the side wheel to the vehicle

body.

2. Slide a Ø10 washer onto the rear

axle.

3. Tighten a lock nut to the end of the

rear axle with a spanner.

Repeat for the other side.

4. Fit the front fender to the front

fork.

5. Insert and tighten two Ø4x12

screws with a screwdriver.

6

21

45

3

Attach the Front Wheel 7

Remove the lock nuts and front axle from the front fork.

1-2. Slide a Ø8 washer to one end of the front axle. Tighten a lock nut to the end of the

front axle with a spanner.

3. Insert the front axle through the hole on one side of the front fork, then through the

hole in the center of the front wheel, and continue to push the front axle through the

hole on the other side of the fork.

4. Slide a Ø8 washer to the front axle.

5. Use a spanner to tighten the lock nut into the front axle. Tip: Use two spanners to

tighten the lock nuts on both sides of the front axle at the same time, but do not

overtighten them, to ensure that the front wheel can rotate freely.

1

3

4

2

5

Attach the Handle bar - 1 8

1. Fit the front fork assembly to the vehicle

body.

2. Align the holes on each side of front fork

with the holes on the vehicle body. Insert

the M8x150 bolt into the hole op top of

the front fork, through the holes on

vehicle body, and out through the hole on

the bottom of the front fender

3. Left up the front fork and tighten a

locknut to the end of the M8x150 bolt with a spanner from the bottom side.

4. Fit the handle to the the front fork.

5. Tighten two lock nuts with a spanner to secure the handle bar to the front fork.

Front bottom View

3

4

1

2

5

6

Attach the Handle bar - 2 9

1-2. Fit the handle bar cover to the front fork. Insert two Ø4x12 screws and tighten with

a screwdriver. And repeat for other handel bar cover.

3. Pass the wire connector on the right handle bar through the cable tie on the front

fork.

4. Plug the wire connector on the handlebar into the connector on the vechiel body.

5-6. Tighten the cable tie, then cut off the excess part of the cable tie with scissors.

1

2

3

Connect the Power Supply 10

1. Remove the seat.

2. Plug the red connector on the vehicle body into the red connector on the battery.

3. Replce the seat.

Top View

2

1

3

4

5

Use Your New Vehicle

1. Power button: Turn the product on and off.

2. Forward button: ● To move the product forward, press the button down.

● To brake or slow down, release pressure from the button.

3. High speed button: Operate the product to move forward in high speed.

4. Low speed button: Operate the product to move forward in low speed.

11

5. Power Indicator

Check the power level of your battery:

All three lights means the battery is 100% (fully) charged.

Two lights means the battery is 66% (mostly) charged.

One light means the battery is 33% charged. We recommend recharging your battery

for 8-12 hours.

No lights means the battery needs charging. Fully charge your battery for 8-12 hours.

Hint: For the most accurate reading, do not operate the vehicle and ensure the

vehicle is stop.

●●○

●○○

○○○

●●●

Charging

1. Plug the charger port into the input socket. (above the right foot pedal)

2. Plug the charger plug into a wall outlet. The battery will begin charging.

WARNING!

ONLY AN ADULT CAN CHARGE AND RECHARGE THE BATTERY!

WARNING!

This product with Charging Protection: when charging, all functions will be cut off! Only an

adult can charge and recharge the battery!

• The POWER SWITCH must be turned in OFF position when charging.

• Before the first use, you should charge the battery for 4-6 hours. Do not recharge the

battery for more than 10 hours to avoid overheating the charger.

• When the vehicle begins to run slowly, recharge the battery.

• After each use or once a month minimum recharge time as 8 to 12 hours, less than 20

hours at most.

• Use the only rechargeable battery and charger supplied with your vehicle. NEVER

substitute the battery or the charger with another brand. Using another battery or

charger may cause a fire or explosion.

- Only use the battery specified by the manufacturer

- Only use the charger specified by the manufacturer.

• Do not use the battery or charger for any other product.

12

Troubleshooting Guide 13

.

Problem Possible Cause Solution

Vehicle does not run

very long

Vehicle runs sluggishly

Vehicle needs a push

to go forward

Difficult shifting from

forward to reverse or

vice-versa

Loud grinding or clicking

noises coming from

motor or gear box

Battery low on power

Thermal fuse has tripped

Battery connector or wires

are loose

Battery is dead

Electrical system is damaged

Motor is damaged

Battery is under charged

Battery is old

Vehicle is overload

Vehicle is being used in harsh

conditions

Poor contact of wires or

Connectors

“Dead Spot” on motor

Motor or gears are damaged

Battery low on power

Recharge battery.

Reset fuse, see <Fuse>

Check that the battery connectors are firmly plugged

into each other. If wires are loose around the motor

contact your distributor please.

Check that the battery connectors are firmly plugged

into each other. If wires are loose around the motor,

contact your distributor please.

A dead spot means the electric power is not being

delivered to the terminal connection and the vehicle

needs repair. Contact your distributor please.

Attempting to shift while the

vehicle is motion

Completely stop the vehicle and shift, see <Use Your

New Vehicle>

Check that the battery connectors are firmly plugged

into each other when recharging

Replace battery, contact your distributor please.

Reduce weight on vehicle.

Avoid using vehicle in harsh conditions ,see <Safety>.

Recharge battery, contact your distributor please.

Contact your distributor please.

Battery will not

recharge

Charger feels warm

when recharging

Battery connector or adapter

connector is loose

Charger not plugged in

Charger is not working

This is normal and not a

cause for concern

Check that the battery connectors are firmly plugged

into each other.

Check that the battery charger is plugged into a

working wall outlet.

Completely read through this manual and the troubleshooting guide table before calling. If you

still need help resolving the problem Contact your distributor please.

Maintaining

• It is parents' responsibility to check main parts of the toy before using,

must regularly examine for potential hazard, such as the battery,

charge,cable or cord, plug, screws are fastening enclosure of other parts

and that in the event of such damage, the toy must not be used until that

damage had been properly removed.

• Make sure the plastic parts of the vehicle are not cracked or broken.

• Occasionally use a lightweight oil to lubricate moving parts such as

wheels.

• Park the vehicle indoors or cover it with a tarp to protect it from wet

weather.

• Keep the vehicle away from sources of heat, such as stoves and heaters.

Plastic parts may melt.

• Recharge the battery after each use. Only an adult can handle the battery.

Recharge the battery at least once a month when the vehicle Raider is not

being used.

• Do not wash the vehicle with a hose. Do not wash the vehicle with soap

and water. Do not drive the vehicle in rainy or snowy weather. Water will

damage the motor, electric system and battery.

• Clean the vehicle with a soft, dry cloth. To restore shine to plastic parts,

use a non-wax furniture polish. Do not use car wax. Do not use abrasive

cleaners.

• Do not drive the vehicle in loose dirt, sand or fine gravel which could

damage the moving parts, motors or the electric system.

• When not using, all the electrical source should be turn off. Turn off the

power switch and disconnect the battery connection.

14

Fuse

Our products are suitable for ASTM F963; GB6675; EN71 and EN62115 standard.

Disposal Of Battery

● Your sealed lead-acid battery must be recycled or disposed of in an environ-

mentally sound manner.

● Do not dispose of your lead-acid battery in a fire. The battery may explode or

leak.

● Do not dispose of a lead-acid battery in your regular, household trash. The

incineration, land filling or mixing of sealed lead-acid batteries with household

trash is prohibited by law.

The battery features a thermal fuse with a rest fuse that will automatically trip and cut all

power to the vehicle if the motor, electric system or battery is overloaded. The fuse will

reset and power will be restored after the unit is turned OFF for 20 seconds and then turned

ON again. If the thermal fuse trips repeatedly during normal use, the vehicle may need

repair. Contact your distributor please.

To avoid losing power, follow these guidelines:

● Do not overload the vehicle.

● Do not tow anything behind the vehicle.

● Do not drive up steep slopes.

● Do not drive into fixed objects, which may cause the wheels to spin, causing the motor to

overheat.

● Do not drive in very hot weather, components may overheat.

● Do not allow water or other liquids to come in contact with the battery or other electric

components.

● Do not tamper with the electric system. Doing so may create a short, causing the fuse to

trip.

15

MOTO ÉLECTRONIQUE

POUR ENFANTS

* Destiné aux enfants de plus de 3 ans

* Poids maximum de l'utilisateur : 30 kg

Lisez et comprenez l'intégralité de ce manuel avant de l'utiliser !

Veuillez conserver ce manuel pour vous y référer ultérieurement car il

contient des informations importantes.

Avant la première utilisation, chargez la batterie pendant au moins 4 à

6 heures, mais pas plus de 10 heures.

AVERTISSEMENT:L'assemblage doit être réalisé par un adulte.

FR

Âge approprié:

Temps de charge:

Capacité de charge:

Taille de la voiture:

À propos de votre nouveau véhicule

3 ans+

8-12 heures

moins de 30 kg

1065×515×680MM

À l'achat de votre nouveau véhicule.

Ce véhicule procurera à votre enfant de nombreux kilomètres de plaisir.

Pour vous assurer une conduite sûre, ainsi qu’à votre enfant, nous vous

prions de lire attentivement ce manuel et de le conserver pour référence

ultérieure.

Suivez les recommandations de ce manuel, elles sont conçues pour

assurer la sécurité et le fonctionnement de votre voiture et de son

conducteur.

SPÉCIFICATIONS:

●Les piles non rechargeables ne doivent pas être rechargées.

●Si des piles rechargeables amovibles sont utilisées, elles ne doivent être

rechargées que sous la surveillance d'un adulte.

●Retirez les piles rechargeables du produit avant de les recharger.

●Ne pas mélanger des piles anciennes et des piles neuves. Ne pas mélanger

différents types de piles : alcalines, standard (carbone-zinc) ou rechargeables

(nickel-cadmium).

●Insérez les piles comme indiqué à l'intérieur du compartiment à piles, anode

vers anode, cathode vers cathode.

●Enlevez les piles lorsque vous n'utilisez pas l'appareil pendant une longue

période. Retirez toujours les piles épuisées du produit. Les fuites et la corrosion

des piles peuvent endommager ce produit. Mettez les piles au rebut en toute

sécurité.

●Ne jamais court-circuiter les bornes de la batterie.

INDICATIONS RELATIVES AUX PILES

batterie

Entrée du

chargeur

Moteur

Vitesse:

12V4.5AH X1

12V390-16000

3.8-5.8 km/h

12V500mA

Dépend de la tension locale

1

Liste des pièces 2

Outils d’assemblage requis: (non inclus):

Tournevis

Corps du véhicule

Roue avant

Fourche avant

Barre du guidon

Couvercle du guidon

Contre-écrou Ø8

6 pcs préinstallés

Axe avant

Rondelle Ø8

préinstallés

Chargeur

Vis Ø4x12

Boulon M8x150

préinstallés

Roue latérale

Siège

préinstallés

Clef à molette

Rondelle Ø10

16

Garde-boue avant

préinstallés

NO. DÉNOMINATION QTÉ (PCS) REMARQUE

14

9

1

2

7

6

12

8

15

15 6

11

13

8

6

63

4

10

5

6

10

16

Schéma des pièces 3

8

La page est en cours de chargement...

Aosom 370-165V80GN Assembly Instructions

Ce manuel convient également à

Aosom 370-165V80GN Assembly Instructions

dans d''autres langues

Documents connexes

Autres documents