MTI Freedom Micro Ii Hs Manuel utilisateur

Marque: MTI

Modèle: Freedom Micro Ii Hs

Taper: Manuel utilisateur

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

REMOVING SMARTCABLE

ATTACHING SMARTCABLE™

Plug SmartCable into the charge port of the device.

Twist the device and bracket off of the position.

The loose cable can be clipped into SpeedBracket™

for easy storage.

Insert SmartCable into the charge port on the puck.

The hooks on cable should click when fully seated.

Insert the crescent end of the

Freedom Micro II

tool

into the opening to the right of the LED. Twist the

Freedom Micro II tool

clockwise 45 degrees and hold

it in place.

Remove the SmartCable from the puck.

Phone should be turned ON, and unlocked

before inserting SmartCable™ while in

MTI Connect® mode.

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

RFID COMMANDS

Default Mode

Enter Standard Mode

Program User Card

Exit Programming Mode

Arm/Disarm Position

Set Lockdown/Unlock While Armed

AUTHORIZATION

VERSA KEY™VERSA KEY™

VERSA KEY™

Double Beep

Double Beep: Accepted

Four Fast Beeps: Rejected

Double Beep:

Accepted

Four Fast Beeps:

Rejected

Tap and Hold Access Card for 10

seconds. It will double beep immediately,

and double beep again after 10 seconds.

Position will automatically lock down

when armed, and unlock when disarmed

when in Lockdown mode.

Flash White every 8 seconds:

Disarmed

Solid White:

Armed

Solid White:

Armed - Locked

Auto time out if no user cards are

added, reverts to Default mode.

Flash White every 8 seconds:

Disarmed

Flash White Every 8

Seconds:

Disarmed - Automatically

unlocks

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

RFID MTI CONNECT PAIRING

Enter Network Mode

Default Mode

Enable Pairing Mode on MTI Connect Hub

System Status

Network

Power Reset

tat

m Sta

atu

Insert MTI Connect

IntelliKey™

for 10 seconds.

Position connects successfully

to mesh network:

Position fails to connect to mesh

network within 3 minutes:

VERSA KEY™

NETWORK PAIRING

Slow Beeps

Double Beep

Four Fast Reject Beeps

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

Visual Reference

System Status

Condition

Solid White

Puck is armed and docked.

Single white ﬂash every 5 seconds

Puck is armed and lifted.

Double white ﬂash every 8 seconds

Puck is docked, but not armed, puck is

connected to a mesh network.

Flashing Red and White with audible alarm

Alarm has been triggered. silence the alarm

and inspect the tether, puck trigger, and base

trigger.

Flashing Red and White with no audible

alarm

Puck is in silent alarm mode. The audible

alarm has exceeded 5 minutes and the

position is unable re-arm itself. inspect the

tether, puck trigger, and base trigger before

attempting to arm the puck.

Solid Yellow

Puck is armed, docked, but has lost it’s

network connection. Ensure the puck is

within range of the MTI Connect

Hub. Try

network pairing again.

*Only applicable when the puck is being

used with the MTI Wireless Network.

LED STATUS INDICATORS

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

Visual Reference

System Status

Condition

Flashing Yellow Every 5 Seconds

Puck is armed, lifted, puck is NOT connected

to a mesh network. Only applicable in

Network Mode.

Solid Blue

After tapping an authorization card: The

puck is in enrollment mode. Tap VersaKey™

to authorize them for use in standard mode.

Enrollment mode closes automatically in 3

minutes.

In normal use: Overcurrent in charging circuit

– most likely a problem in the SmartCable™.

Flashing Blue

Puck has entered network pairing mode.

Stops upon successful pairing, or after 90

seconds.

Single Red Flash

TO BE VERIFIED:

Only follows an attempt to

arm the puck. Occurs when the puck cannot

arm, for example, due to a released trigger

but the user attempts to arm the puck with

the app or key.

Multi-colored ﬂash

Puck has received an “identify” command

from a user of the MTI Connect

software.

Flashing Green

Puck is disarmed in factory default mode.

Complete the setup for Standard or Network

mode to use VersaKey™ or MTI Connect

Note: The puck may automatically arm while

in this default mode, as long as all triggers

are closed for 15 minutes. Once it arms, the

LED will turn solid white.

LED STATUS INDICATORS

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

PUCK DIMENSIONS

RISER DIMENSIONS

2.74”

2.05”

4.36”

4.38”

1.84”

1.85”

3.45”

60°

1.28”

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

RISER WITH ADAPTER DIMENSIONS

2.80”

Slot Adapter shown.

Through-hole adapter is

identical in size/ appearance

minus these tabs.

2.74”

1.89”

4.36”

4.38”

1.84”

3.45”

60°

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

BRACKET DIMENSIONS

1.11”

MAXIMUM: 180mm H x 90mm W

Accomodates Phones

7-9mm Thick

MINIMUM: 118mm H x 65mm W

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

FCC ID: 2AA2X-15000282

Model: ROUND FREEDOM MICRO II HS

FCC Statement

This device complies with Part 15 of the FCC Rules.

Caution: If any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

The grantee is not responsible for any changes or modiﬁcations not expressly approved by the party responsible for compliance. Such modiﬁcations could

void the user’s authority to operate the equipment.

The RF Exposure Compliance distance is 20 millimeters.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

ISED Certiﬁcation Number: 24439-15000282

Model: ROUND FREEDOM MICRO II HS

ISED Statement

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage

est susceptible de compromettre le fomctionnement du dispositif.

CAN ICES-3(B)/NMB-3(B)

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain

Canadian information on RF exposure and compliance.

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf,

utilisateurs peut obtenir l’information canadienne sur l’exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated

with a minimum distance of 20 millimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et

actionné avec une distance minimum de 20 millimètres entre le radiateur et votre corps.

Technical Data

Operating Temperature:

0°C to 40°C

Operating Frequency:

2405 MHz to 2480 MHz

Max Power:

Less than 4 dBm at 2.4 GHz

Operating Frequency:

125kHz