Campbell Hausfeld XT001000 Manuel utilisateur

3/8 inch Impact Wrench

Operating Instructions

Model: XT001000

IN745000 6/17

A Marmon/Berkshire Hathaway Company

EN

REGISTER YOUR PRODUCT ONLINE NOW! www.campbellhausfeld.com/reg

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS • DO NOT DISCARD

Please read and save these instructions. Read carefully before

attempting to assemble, install, operate or maintain the product

described.

Protect yourself and others by observing all safety information. Failure

to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Model #: ________________________________

Serial #: ________________________________

Purchase Date: __________________________

For parts, product & service information

visit www.campbellhausfeld.com

Campbell Hausfeld

100 Production Drive

Harrison, Ohio 45030

1

BEFORE YOU BEGIN

Description

This is the right tool for the job when you need a smaller impact wrench

that doesn’t compromise on power. The balanced twin-hammer mechanism

reduces vibration making this wrench more comfortable to use. And the small

size gives you the support you need in tight spaces to get the job done.

Campbell Hausfeld

®

makes it easier for you to finish your projects like a pro.

The company’s history of creating quality products began in 1836, when

it manufactured horse-drawn wagons and agricultural equipment. Today,

Campbell Hausfeld offers a complete line of air compressors, air tools and

accessories, inflators, nailers and staplers, spray guns, pressure washers, and

more. Finish your projects faster and easier with Campbell Hausfeld – The Air

Power Expert.

UNPACKING

After unpacking the unit, inspect carefully for any damage that may have

occurred during transit. Check for loose, missing or damaged parts. Check

to be sure all supplied accessories are enclosed with the unit. In case of

questions, damaged or missing parts, please visit www.campbellhausfeld.com

for customer assistance.

Do not operate unit if damaged during shipping,

handling or use. Damage may result in bursting and

cause injury or property damage.

Other Parts (Not Provided)

You will need the following items and/or accessories to properly set-up and

optimally use your GSD impact wrench:

• 1/4 inch Plug NPT (M)

o For less stress on your air hose and you, try a flex plug.

• 3/8 inch (ID) Air Hose

• 1/4 inch Coupler NPT (F)

o Eliminate coupler confusion with a universal coupler style.

o Quick-connect couplers quickly, easily join hoses to tools.

o If you don’t use a flex plug, consider a swivel coupler to prevent

hose kinks and reduce stress on your air hose.

• 8 Gallon air compressor or larger

• Impact drive sockets

• PTFE tape for all fitting connections

• Adjustable wrench for tightening fitting connections

See www.campbellhausfeld.com for additional information on accessories to

support your air tools and pneumatic system.

2

BEST PRACTICES

u For best output, maintain pressure at the tool of 90 PSI.

u The longer your air hose the greater the pressure drop from compressor to tool.

If you are using a hose longer than 50 feet, consider upgrading to a 1/2 inch ID air

hose to ensure proper tool pressure.

u Failure to lubricate and maintain your air tools properly will dramatically shorten

their life. Use oil every time you use your air tool to lubricate, clean and inhibit rust

in one step. Campbell Hausfeld sells air tool oil under part number ST1270.

SPECIFICATIONS

XT001000

Maximum PSI 90

CFM under load 100% duty 3.4 CFM @ 90 PSI

CFM no load 100% duty 5.6 CFM @ 90 PSI

SCFM under load 100% duty 24.8 SCFM @ 90 PSI

SCFM no load 100% duty 40.1 SCFM @ 90 PSI

Air Compressor Recommendation 8 gallon

Max Torque 160 Ft. Lbs.

Working Torque 0 - 130 Ft. Lbs.

Rated RPM (free speed) 12,000

Impact Speed (IPM) 1,300

Variable Speed Yes

Reverse 1

Forward 3

Impact Mechanism Type Twin Hammer

Bolt Capacity 1/2 inch

Air Inlet 1/4 inch NPT (F)

Minimum Hose Size 3/8 inch

Anvil 3/8 inch

Housing Material Composite

Tool Weight 2.8 Lbs.

Tool Length 6-1/2 inches

Tool Height 6-5/8 inches

Tool Width 2-1/2 inches

3

GETTING TO KNOW YOUR UNIT

SET UP INSTRUCTIONS

BEST PRACTICES

u The air compressor used with your impact wrench must be able to maintain a

minimum of 90 PSI when the tool is being used. An inadequate air supply can

cause a loss of power and inconsistent tool output/performance.

u A pressure regulator—used at the tool--is helpful to control the operating pressure

of the tool and maintain 90 PSI.

u Use an oiler to provide oil circulation through the tool and a filter to remove liquid

and solid impurities which can rust or “gum up” internal parts of the tool.

u To disconnect a coupler/plug from a system set-up: push the coupler and plug

together before pulling the coupler sleeve back and separating the coupler and

plug.

u Use only sockets specifically rated as “impact” drive sockets. Non-impact drive

sockets—if used with air tools—can shatter causing serious personal injury.

Plug

Quick

Coupler

Air Hose

* Items shown in Set Up Instructions are not included with this tool.

Air Inlet

Exhaust Port

Anvil

Trigger

Forward-Reverse

Dial/Air-flow

Regulator

4

LUBRICATION

To protect your tool, lubricate the motor every time--before and after--you

use this tool. You cannot oil the motor too often or put too much oil in the

air inlet.

1. Disconnect the impact wrench from air supply.

2. Turn the tool upside down.

3. While pulling the trigger, pour approximately a teaspoon of air tool

oil in the air inlet. Campbell Hausfeld makes air tool oil under model

number ST1270.

4. Turn the forward and reverse knob in both directions to ensure that oil

gets in all passages.

5. Connect the tool to the air supply and cover the exhaust port with a

towel. Run the impact wrench in both the forward and reverse directions

for about 10 seconds. Oil will spray from the exhaust port when the tool

is triggered.

6. Continue to run until no oil is discharged.

7. Wipe all residual oil from tool before use.

OPERATING INSTRUCTIONS

AIR-FLOW/SPEED ADJUSTMENT

The air-flow regulator controls how much air

enters the motor which defines the motor speed/

power. This impact wrench has 4 power/speed

settings—3 forward and 1 reverse. Use the knob

on the rear of the tool to select the desired setting

before operating the tool.

To change power/speed setting, turn the knob to

align with the dot size (largest dot = maximum

power). Do not change power settings while the

tool is running as this causes unnecessary stress on internal parts.

To remove nuts or bolts, set the air-flow regulator to reverse by turning

the knob to the left (counter clockwise), aligning with the single large dot.

Attach the appropriate sized IMPACT socket. Place socket over bolt and pull

trigger until bolt has been removed.

To install a nut or bolt, set the air-flow regulator to the appropriate forward

setting. Attach the IMPACT socket and place over the nut or bolt. Pull the

trigger and hold impact wrench over screw until nut or bolt has been seated.

Use a torque wrench to attain the proper torque manually. Do not over

tighten.

BEST PRACTICES

u To prevent cross-threading, start your nuts/bolts by hand--try to get a few

rotations--before continuing the job with your pneumatic tool.

u The impact wrench should never be used to set torque. Use a torque wrench to

attain the proper torque manually. Do not over tighten.

5

STORAGE

Lubricate your impact wrench before storing. Follow the air motor lubrication

instructions with an exception to step #5. Only run the impact wrench for

2-3 seconds (instead of 10 seconds) because more oil needs to remain in the

impact wrench when storing. Store your tool in a cool dry place.

TECHNICAL SERVICE

For information regarding the operation or repair of this product, please visit

www.campbellhausfeld.com.

SAFETY INSTRUCTIONS

This manual contains information that is very important to know and

understand. This information is provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help recognize this information, observe the

symbols found on page 8. The Safety Symbols throughout this manual are to

alert you to important safety hazards and precautions.

The DANGER, WARNING, CAUTION, and NOTICE notifications

and instructions in this manual cannot cover all possible condi-

tions and situations that may occur. It must be understood by

the operator that caution is a factor which cannot be built into

this product, but must be supplied by the operator.

With any piece of equipment, new or used, the most important part of its

operation is SAFETY!

Campbell Hausfeld encourages you to familiarize yourself with your new

equipment and stresses safe operation.

The next few pages of this manual are a summary of the main safety aspects

associated with this unit. Be sure to read and understand completely before

operating the machine.

The symbols used throughout the operation and maintenance sections of

this manual call attention to safety procedures.

Important Safety Information

Please read and save these instructions. Read carefully before attempting to

assemble, install, operate or maintain the product described. Protect yourself

and others by observing all safety information. Failure to comply with

instructions could result in personal injury and/or property damage! Retain

instructions for future reference.

This manual contains important safety, operational and maintenance

information. If you have any questions, please visit

www.campbellhausfeld.com for customer assistance.

6

SAFETY INSTRUCTIONS (CONTINUED)

California Proposition 65

This product can expose you to chemicals including

lead, which are known to the State of California

to cause cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

Illinois Lead Poisoning Prevention Act

Contains lead. May be harmful if eaten or chewed.

Complies with Federal Standards.

General Safety

This product is a part of a high pressure system and the following safety

precautions must be followed at all times along with any other existing safety

rules.

1. Read all manuals included with this product carefully. Be thoroughly

familiar with the controls and the proper use of the equipment.

2. Only persons well acquainted with these rules of safe operation should

be allowed to use the air tool.

Do not exceed maximum operating pressure of the

air tool (90 PSI). The air tool could explode and result

in death or serious personal injury.

3. Do not exceed any pressure rating of any component in the system.

4. Disconnect the air tool from air supply before changing tools or

attachments, servicing and during non-operation.

Safety glasses and ear protection must be worn

during operation.

5. Do not wear loose fitting clothing, scarves, or neck ties. Loose clothing

may become caught in moving parts and result in serious personal injury.

6. Do not wear jewelry when operating any tool. Jewelry may become

caught in moving parts and result in serious personal injury.

7. Do not depress trigger when connecting the air supply hose.

8. Always use attachments designed for use with air powered tools. Do not

use damaged or worn attachments.

Do not use hand tool sockets. Use impact quality

sockets only. Hand tool sockets are “glass-hard” and

will shatter and can cause serious personal injury if used with air tools.

9. Never trigger the tool when not applied to a work object. Attachments

must be securely attached. Loose attachments can cause serious injury.

10. Protect air lines from damage or puncture.

11. Never point an air tool at oneself or any other person. Serious injury

could occur.

MANUAL

7

12. Check air hoses for weak or worn condition before each use. Make sure

all connections are secure.

Never carry a tool by the hose or pull the hose to

move the tool or a compressor. Keep hoses away

from heat, oil and sharp edges. Replace any hose that is damaged, weak or

worn.

Release all pressure from the system before

attempting to install, service, relocate or perform

any maintenance.

13. Keep all nuts, bolts and screws tight and ensure equipment is in safe

working condition.

14. Do not put hands near or under moving parts.

Do not misuse this product. Excessive exposure to

vibration, work in awkward positions, and repetitive

work motions can cause injury to hands and arms. Stop using any tool if

discomfort, numbness, tingling, or pain occur, and consult a physician.

This impact wrench requires lubrication BEFORE the

initial use and BEFORE and AFTER each additional

use.

Disconnect the impact wrench from the air supply

before lubricating.

After an air tool has been lubricated, oil will

discharge through the exhaust port during the first

few seconds of operation. Thus, THE EXHAUST PORT MUST BE COVERED

WITH A TOWEL before applying air pressure. FAILURE TO COVER THE

EXHAUST PORT CAN RESULT IN SERIOUS INJURY.

When reassembling be careful not to overtighten.

Bolts may fail or cause a hazardous condition. Be

sure to set the regulator to the minimum setting then use a torque wrench

to set torque.

8

SAFETY INSTRUCTIONS (CONTINUED)

Safety Glossary

This manual contains information that is very important to know and

understand. This information is provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help recognize this information, observe the

following symbols.

Danger indicates an imminently hazardous situation

which, if not avoided, WILL result in death or serious

injury.

Warning indicates a potentially hazardous situation

which, if not avoided, COULD result in death or

serious injury.

Caution indicates a potentially hazardous situation

which, if not avoided, MAY result in minor or

moderate injury.

Notice indicates important information, that if not

followed, may cause damage to equipment.

IMPORTANT or NOTE: Information that requires special attention.

Safety Symbols

The following Safety Symbols appear throughout this manual to alert you to

important safety hazards and precautions.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

MANUAL

Wear Eye

and Mask

Protection

Read Manual

First

Risk of

Explosion

Wear Eye

and Hearing

Protection

Risk of

Pressure

9

NOTES:

10

GENERAL TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Tool runs slowly or will

not operate

1. Grit or gum in tool 1. Flush the tool with Campbell

Hausfeld air tool oil, gum solvent, or

an equal mixture of SAE 10 motor

oil and kerosene. Lubricate the

tool after cleaning with Campbell

Hausfeld (or comparable) air tool oil.

2. No oil in tool 2. Lubricate the tool according to

the lubrication instructions in this

manual.

3. Low air pressure 3. a. Adjust the regulator on the tool

to a higher setting.

b. Adjust the compressor regulator

to 90 PSI while the tool is running

free.

4. Air hose leaks 4. Tighten and seal hose fittings, if leaks

are found.

5. Pressure drops 5. a. Be sure the hose is the proper

size. Long hoses or tools using

large volumes of air may require

a hose with an I.D. of 1/2 inch or

larger depending on the total

length of the hose.

b. Do not use a multiple number of

hoses connected together with

quick connect fittings. This causes

additional pressure drops and

reduces the tool power. Directly

connect the hoses together.

Moisture blowing out

of tool

1. Water in tank 1. Drain tank. (See air compressor

manual). Oil tool and run until no

water is evident. Oil tool again and

run 1-2 seconds.

2. Water in the air lines/hoses 2. a. Install a water separator/filter.

NOTE: Separators only work

properly when the air passing

through the separator is cool.

Locate the separator/filter as far

as possible from the compressor.

b. Install an air dryer.

11

IMPACT MECHANISM TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Impacts slowly or will

not impact

1. Lack of lubrication 1. Lubricate the air motor. (See

Lubrication section of this manual).

2. Tool regulator set in wrong

position

2. a. Adjust the regulator on the tool

to the appropriate setting.

b. Regulator should be turned

so the indicator points to the

appropriate dot on the tool.

3. In-line regulator or

compressor regulator set too

low

3. Adjust regulators in the air system.

Impacts rapidly but

will not remove bolts

Worn impact mechanism Replace tool.

Does not impact Broken impact mechanism Replace tool.

Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it

for safekeeping.

LIMITED WARRANTY

1. DURATION: From the date of purchase by the original purchaser as follows: Two (2) Years.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld, a Marmon/Berkshire Hathaway

Company, 100 Production Drive, Harrison, Ohio, 45030. Visit www.campbellhausfeld.com.

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of

resale) of the Campbell Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld air tool.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which

occur within the duration of the warranty period with the exceptions below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR

PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION.

If this product is used for commercial, industrial or rental purposes, the warranty will apply for

ninety (90) days from the date of purchase. Some States do not allow limitation on how long an

implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY

RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD

PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate

products in accordance with instructions provided in the owner’s manual(s) supplied with

product. Accident, purchaser’s abuse, neglect or failure to operate products in accordance with

instructions shall also include the removal or alteration of any safety devices. If such safety

devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s

option, products or components which are defective, have malfunctioned and/or failed to conform

within the duration of the specific warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Visit www.campbellhausfeld.com to obtain your warranty service options. Freight costs must be

borne by the purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the

owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair

or replacement will be scheduled and serviced according to the normal work flow at the servicing

location, and depending on the availability of replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal

rights. You may also have other rights which vary from state to state or country to country.

12

Clé à chocs 9,53 mm (3/8 po)

Instructions d’Utilisation

Modèle: XT001000

IN745000 6/17

A Marmon/Berkshire Hathaway Company

FR

ENREGISTREZ VOTRE PRODUIT EN LIGNE MAINTENANT !

www.campbellhausfeld.com/reg

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS

CONSERVER CES INSTRUCTIONS • NE PAS JETER

Lire et conserver ces instructions. Il faut les lire attentivement avant

de commencer à assembler, installer, faire fonctionner ou entretenir

l’appareil décrit.

Pour se protéger et protéger autrui, observer toutes les informations sur

la sécurité. Négliger d’appliquer ces instructions peut causer

des blessures et/ou des dommages matériels! Conserver ces instructions

pour consultation ultérieure.

RAPPEL: Conservez votre preuve d’achat datée aux ﬁns de garantie!

Attachez-le à ce manuel ou classez-le pour le garder en sécurité.

N° de modèle : _____________________________

N° de série : _______________________________

Date d’achat : _____________________________

Pour de l’information sur les pièces,

produits et services veuillez visiter

www.campbellhausfeld.com

Campbell Hausfeld

100 Production Drive

Harrison, Ohio 45030

Fr1

AVANT DE COMMENCER

Description

Il s’agit de l’outil convenant au travail lorsqu’il vous faut une clé à chocs

de plus petite dimension, sans compromettre la puissance. Le mécanisme

à doubles marteaux réduit les vibrations, ce qui la rend plus confortable

à utiliser. Sa petite taille vous offre le support dont vous avez besoin pour

travailler dans les espaces restreints.

CampbellHausfeld

®

vous facilite le travail afin de terminer vos projets en pro.

L’histoire de l’entreprise est parsemée de produits de qualités depuis 1836,

alors que furent fabriqués les wagons tirés par les chevaux et les équipements

agraires. Aujourd’hui, Campbell Hausfeld offre une gamme complète de

compresseurs, outils et d’accessoires pneumatiques, pompes de gonflage,

de cloueurs, agrafeuses, pistolets pulvérisateurs, laveuses à pression, et plus.

Terminez vos projets plus rapidement et plus facilement grâce à Campbell

Hausfeld – l’expert de la puissance de l’air.

DÉBALLAGE

Dès que l’appareil est déballé, l’inspecter attentivement pour tout signe

de dommages en transit. Vérifier s’il y a des pièces desserrées, manquantes

ou endommagées. Vérifier pour s’assurer que tous les accessoires fournis

sont inclus avec l’appareil. Pour toutes questions, pièces endommagées ou

manquantes, veuillez visiter www.campbellhausfeld.com pour l’assistance à la

clientèle.

Ne pas utiliser un modèle qui a été endommagé

pendant le transport, la manipulation ou l’utilisation.

Le dommage peut résulter en explosion et peut causer des blessures ou

dégâts matériels.

Autres pièces (non fournies)

Il vous faudra les éléments et/ou accessoires suivants pour correctement

mettre en marche et utiliser de manière optimale votre clé à chocs GSD:

• Connecteur 6,4 mm (1/4 po) NTP (M)

o Pour une réduction du stress pour vous et votre tuyau, essayez un

connecteur flexible.

• Tuyau à air 9,5 mm (3/8 po) (DIA. INT.)

• Raccord 6,4 mm (1/4 po) NPT (F)

o Élimine la confusion par l’utilisation d’un raccord de style universel.

o Les coupleurs à attache rapide raccordent rapidement et facilement

les tuyaux aux outils.

o Si vous n’utilisez pas un connecteur flexible, un raccord pivotant

pourrait être utilisé afin d’éviter l’entortillement et réduire le stress

imposé à votre tuyau d’air.

• Compresseur d’air 30,28L (8gal) ou plus.

• Douilles à chocs

• Ruban PTFE pour tous les joints des raccords

• Clé ajustable pour serrer les joints des raccords

Voir au www.campbellhausfeld.com pour d’autres informations sur les

accessoires accompagnant vos outils et votre système pneumatique.

Fr2

MEILLEURES PRATIQUES

u Pour une meilleure puissance, maintenez la pression à l’outil de 621 kPa.

u Plus votre tuyau à air est long, plus la pression diminuera entre le compresseur et

l’outil. Si vous utilisez un tuyau à air dépassant 15,2m (50 pi), on devrait plutôt

utiliser un tuyau à air de 12,7 mm (1/2 po) de dia. int. pour assurer une pression

appropriée à l’outil.

u À défaut de lubrifier et de correctement entretenir vos outils pneumatiques

diminuera drastiquement leur durée de vie. Utilisez de l’huile chaque fois que

vous utilisez votre outil pour le lubrifier, le nettoyer et éviter la rouille, en une

seule étape. Campbell Hausfeld offre une huile à outils pneumatiques sous le

numéro de pièceST1270.

CARACTÉRISTIQUES TECHNIQUES

XT001000

kPa maximum 621

pi³/min (l/min) en charge de service à 100% 96,3 l/min @ 621 kPa

pi³/min (l/min) sans charge de service à 100% 158,6 l/min @ 621 kPa

pi³/min standard (l/min) en charge de service à 100% 702,3 l/min @ 621 kPa

pi³/min standard (l/min) sans charge de service à 100% 1135,5 l/min @ 621 kPa

Recommandation pour le compresseur d’air 30,28 L

Couple maximal 160pi-lb

Couple résistant 0 - 130pi-lb

Classification RPM (vitesse à vide) 12,000

Vitesse d’impact (BPM) 1,300

Vitesse variable Oui

Vers l’arrière 1

Vers l’avant 3

Type de mécanisme de choc Double marteau

Capacité de boulonnage 1/2 po (12,7 mm)

Arrivée d’air 6,4 mm (1/4 po) NPT (F)

Taille minimum du tuyau 9,5 mm (3/8 po)

Enclume 9,5 mm (3/8 po)

Matériau du logement Composite

Poids de l’outil 1,27 kg

Longueur du tuyau 16,51 cm

Hauteur de l’outil 16,83 cm

Largeur du tuyau 6,35 cm

Fr3

APPRENEZ À CONNAÎTRE VOTRE UNITÉ

INSTRUCTIONS DE MISE EN MARCHE

MEILLEURES PRATIQUES

u Le compresseur d’air utilisé avec votre clé à chocs doit être capable de maintenir

au moins 621 kPa lorsque l’outil est en fonction. Un approvisionnement d’air

inadéquat peut causer une perte de puissance et une performance inconstante de

l’outil.

u Un régulateur de pression – utilisé sur l’outil – est utile pour contrôler la pression

de fonctionnement de l’outil et maintenir 621 kPa.

u Utilisez un huileur pour offrir une circulation de l’huile dans l’outil et un filtre pour

retirer les impuretés liquides et solides pouvant causer la rouille ou de l’encrassage.

u Pour débrancher un raccord/embout d’un système: poussez le raccord et l'embout

ensemble avant de tirer le manchon du raccord vers l’arrière et en séparant le

coupleur et l'embout.

u N’utilisez que des douilles spécifiquement classifiées comme des douilles à chocs.

Si des douilles ordinaires étaient utilisées avec des outils pneumatiques, elles

pourraient se fissurer et causer de graves blessures corporelles.

* Les éléments montrés aux Instructions de mise en marche ne sont pas inclus avec cet outil.

Arrivée d’air

Sortie de

l’échappement

Enclume

Détente

Cadran avant-

arrière/régulateur

de débit d’air

Bouchon

Raccord

Rapide

Tuyau À Air

Fr4

LUBRIFICATION

Pour protéger votre outil, lubrifiez le moteur chaque fois –avant et après–

l’avoir utilisé. Vous ne pouvez huiler le moteur trop fréquemment ou placer

trop d’huile dans l’arrivée d’air.

1. Débranchez la clé à chocs de l’alimentation d’air.

2. Tournez l’outil à l’envers.

3. En tirant sur la détente, versez environ une cuillerée à thé d’huile

à outils pneumatiques dans l’arrivée d’air. Campbell Hausfeld offre

une huile à outils pneumatiques sous le numéro de modèle ST1270.

4. Tournez le bouton d’avance/recul dans les deux directions afin d’assurer

que l’huile pénètre dans tous les passages.

5. Connectez l’outil à l’alimentation d’air et couvrez la sortie de

l’échappement avec une serviette. Faites fonctionner la clé à chocs dans

les deux sens pendant environ 10secondes chaque fois. L’huile sera

pulvérisée par la sortie de l’échappement lorsque l’outil sera mis en

marche.

6. Continuez tant qu’il y aura de l’huile.

7. Essuyez toute huile résiduelle de l’outil avant de l’utiliser.

MODE D’EMPLOI

AJUSTEMENT DU DÉBIT D’AIR/VITESSE

Le régulateur de débit d’air contrôle la quantité

d’air qui entre dans le moteur, définissant ainsi sa

vitesse/puissance. Cette clé à chocs a 4réglages

de puissance/vitesse – 3 vers l’avant et 1 vers

l’arrière. Utilisez le bouton à l’arrière de l’outil afin

de sélectionner le réglage désiré avant de faire

fonctionner l’outil.

Pour changer de puissance/vitesse, tournez le

bouton pour l’aligner avec la taille de point (gros

point = puissance maximale). Ne changez pas les réglages de puissance

lorsque l’outil est en fonction, ce qui imposerait un stress inutile aux pièces

internes.

Pour retirer les écrous ou les boulons, réglez le régulateur du débit d’air à

l’inverse en tournant le bouton vers la gauche (sens horaire), l’alignant avec

le plus gros point. Attachez la douille à CHOCS de la taille appropriée. Placez

la douille sur le boulon et actionnez la détente jusqu’à ce que le boulon ait

été retiré.

Pour mettre un écrou ou un boulon en place, réglez le régulateur du débit

d’air au réglage avant approprié. Attachez la douille à CHOCS et placez-la

sur l’écrou ou le boulon. Actionnez la détente et maintenez la clé à chocs sur

la vis jusqu’à ce que l’écrou ou le boulon soit bien en place. Utilisez une clé

dynamométrique pour atteindre manuellement le couple approprié. Ne pas

trop serrer.

MEILLEURES PRATIQUES

u Pour éviter l’arrachement des filets, commencez à visser à la main de quelques tours

votre écrou/boulon, avant de continuer le travail avec votre outil pneumatique.

u

La clé à chocs ne devrait jamais être utilisée pour régler le couple. Utilisez une clé

dynamométrique pour atteindre manuellement le couple approprié. Ne pas trop serrer.

La page charge ...

Campbell Hausfeld XT001000 Manuel utilisateur

Ce manuel convient également à

Campbell Hausfeld XT001000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents