Powermate PFTT142 Manuel utilisateur

Marque: Powermate

Modèle: PFTT142

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Ce manuel convient également à

SFTT142

07/11/2018 Printed in China A203399

Look inside for:

Page

Safety Definitions ...............................2-3

Important Safety Information ......................3-5

Product Specifications ............................6

Parts & Features ................................6

Safety Decals ...................................7

Assembly .....................................8-10

Engine Preparation...............................11

Operation ....................................12-15

Maintenance..................................16-18

Technical Service .............................. 18

Troubleshooting ............................... 19

Warranty...................................... 20

Operator’s Manual

FRONT TINE

ROTARY TILLER

KEEP THIS MANUAL FOR FUTURE REFERENCE

Record the following for future reference:

Mfg. Date Code:___________

Date of Purchase:_____________ Attach a copy of your sales receipt.

Consumer Toll Free Number: 1-800-737-2112

Refer to the website for electronic manual and parts book.

www.powermateoutdoor.com

IMPORTANT:

Thank you for purchasing this Powermate® Tiller.

This manual provides complete instructions for safely operating and maintaining your Tiller. Read and save these instructions. Refer

to this manual each time before using your Tiller.

CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash hands after use. Keep out of reach of

children.

This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or

other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Model No. PFTT142.1

If you have a question or problem...

CALL TOLL FREE: 1-800-737-2112

WARNING

Important Safety Information

Safety Definitions

• Save these instructions

Look for this symbol to point out important safety precautions. It means: Attention! Become Alert!

Your Safety Is Involved.

Read operator’s manual before operating this machine. Failure to follow directions could result in

serious injury.

Thrown objects. Remove all rocks, stones, and foreign objects which could be thrown by machine.

Do not use if children or bystanders are present.

Rotating tines can cause serious injury. Keep hands, feet, and clothing away.

Wear eye protection complying with ANSI Z87.1 and hearing protection.

Disconnect spark plug wire when not in use or before servicing, cleaning, or performing maintenance on the unit.

Engine exhaust contains carbon monoxide, an odorless and deadly gas. NEVER run unit indoors or in a poorly

ventilated area.

Do NOT touch hot muffler or cylinder. These parts are extremely hot from operation and may remain hot for a short time

after operation.

To reduce risk of fire, clean spilled gas and oil and keep unit free from debris. Gasoline is extremely flammable. Allow

machine to cool before refueling.

Control and Operating Symbols

The following symbols are used on the product and in this manual to alert the operator of potential safety hazards. Read them

carefully, and understand their meaning.

Safety Alert Symbols

Safety Warning Symbols

The following symbols may be found on your tiller. Carefully read and understand their meaning.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor/moderate injury.

NOTICE

Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

Oil Fill Location: Do Not Overfill. Add engine oil and check quantity at this location

CLUTCH

CONTROL

DISENGAGE

ENGAGE

Clutch Lever: Lifting the lever engages the tines.

Do not use gasoline containing more than 10% ethanol.

Push primer 3 times before starting a cold engine. Important: For starting a hot engine, push only once.

Responsibility of Operator

1. Carefully read and follow these safety instructions. Failure to do so can result in serious injury.

Know your product. Read and understand this manual before use. Compare the illustrations to unit. Learn location

and function of all controls. Thoroughly understanding the unit before use will result in the best performance and safety.

3. Follow all instructions when assembling the unit. If the unit was purchased in assembled condition, the operator must

check the unit carefully to make sure it was assembled according the instructions in the manual before use.

4. Regularly inspect the tiller. Make sure parts are not bent, damaged, or loose.

5. Use this equipment for its intended purpose only.

6. Operate the unit only with guards, shields, and other safety items in place and working correctly.

7. Service the unit only with authorized or approved replacement parts.

8. Complete all unit maintenance and adjustments according to the instructions in this manual.

WARNING

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm.

WARNING

To prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug

wire and put wire where it cannot contact the spark plug.

Preparation Safety

WARNING

• Read, understand, and follow all instructions on the machine and in this manual. Be thoroughly familiar with the

controls and the proper use of the tiller before starting. Know how to stop the engine quickly.

• Familiarize yourself with all the safety and operating decals on this equipment.

• Thoroughly inspect the area where the tiller is to be used and remove all foreign objects. Your equipment can propel

small objects at high speed causing personal injury or property damage. Stay away from breakable objects, such as

house windows, auto glass, greenhouses, etc.

• Check that all nuts and bolts are tight and equipment is in good condition before each use.

Operation Safety

• Never allow children or young teenagers to operate the tiller.

WARNING

• Keep area of operation clear of all bystanders, particularly small children and pets.

• Only allow responsible individuals, who are familiar with the instructions, to operate the tiller.

• Do not operate the tiller while under the influence of alcohol, drugs, or other medication which can cause drowsiness

or affect your ability to operate this machine safely.

• Do not use this machine if you are mentally or physically unable to operate the machine safely.

• Always wear ANSI compliant safety goggles or safety glasses with side shields when operating tiller to protect your

eyes from foreign objects, which can be thrown from the unit.

• Wear appropriate clothing such as a long sleeved shirt or jacket. Also wear long trousers or slacks. Do NOT wear

shorts. Do NOT wear loose clothing, which could get caught in this equipment.

Important Safety Information

• Save all instructions

Important Safety Information

Safety Definitions

• Save these instructions

Ignition Switch: Move switch position to start/stop engine.

Place free hand on handle bar before pulling recoil starter handle with other hand.

Control and Operating Symbols (Continued)

Important Safety Information (Continued)

• Save all instructions

Important Safety Information

Operation Safety

• Always wear work gloves and sturdy footwear such as leather work shoes or short boots. These will protect ankles

and shins from small sticks, splinters, and other flying debris, and improve traction.

• It is advisable to wear protective headgear to protect against being struck by small flying particles, or being struck by

low hanging branches, twigs, or other objects, which may be unnoticed by the operator.

WARNING

• Do not put hands or feet near or under rotating parts.

• Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards

or traffic.

• Exercise caution to avoid slipping or falling. Always be sure of your footing; keep a firm hold on the handle and walk;

never run. Never operate the tiller at high transport speeds on slippery surfaces.

• Never operate the tiller without good visibility or light.

DANGER

• Do not run the engine indoors or inside a closed area. The exhaust fumes are dangerous, containing CARBON

MONOXIDE, an ODORLESS AND DEADLY GAS.

• Never leave the tiller unattended when the engine is running. Stop the engine and make sure all moving parts have

stopped. Remove the wire from the spark plug.

• Watch for holes, ruts, bumps, or other rough ground. Tall grass can hide obstacles.

• Always look behind and down and use caution when using reverse or pulling the tiller towards you.

• Never attempt to start the tiller unless both wheels are in the locked position. This acts as a brake for the tiller.

Always start the tiller on the level surface.

WARNING

• Disengage clutch lever and stop engine before leaving the tiller in operating position. Wait until the tines come to a

complete stop before removing debris or making any adjustments to the tiller.

• Do not attempt to till hard soil, till too deep or till at too fast a rate that can overload the tiller.

• If the tiller should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and prevent it from

touching the spark plug. Check immediately for the cause. Vibration is generally a warning of trouble.

• When transporting the unit, rotate the wheel assembly forward under the engine and move by pulling the unit

rearward. This will keep the transport wheels locked into position.

Fuel Safety

WARNING

• Gasoline is extremely flammable, and gasoline vapors can explode if ignited. Handle with care.

• Use an approved container.

• Check fuel supply before each use, allowing space for expansion as the heat of the engine and/or sun can cause fuel

to expand.

• Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool a minimum of 2 minutes

before refueling.

• Do not smoke while refueling.

• After refueling, replace fuel tank cap securely and wipe up spilled fuel.

• Never store fuel or tiller with fuel in the tank inside a building where fumes may reach an open flame.

• Never fill gasoline containers or the tiller fuel tank inside of a vehicle or in a truck bed. Accidental electrical static dis

charge can ignite fuel vapors which could result in serious injury or death.

Storage Safety

•

Always refer to the operator’s manual instructions for important details if the tiller is to be stored for an extended period.

• Never store the tiller with fuel in the fuel tank inside a building where ignition sources are present such as water

heaters, space heaters, clothes dryers, etc.

• To reduce fire hazard, keep tiller free of grass, leaves, or other debris build-up.

• Allow the engine to cool before storing in any enclosure.

Important Safety Information (Continued)

• Save all instructions

Important Safety Information

Repair, Maintenance, and Adjustment Safety

• After striking a foreign object, stop the engine. Remove the wire from the spark plug and keep the wire away from the

plug to prevent accidental starting. Thoroughly inspect the tiller for any damage. If damaged, have the equipment

repaired by a trained technician before restarting and operating.

WARNING

• Stop the engine before cleaning, repairing, or inspecting the unit. Make sure all moving parts have stopped. Let the

engine cool, disconnect the spark plug wire and move it away from the spark plug.

• Never attempt to make any adjustments while the engine is running except when specifically recommended by the

manufacturer.

• Keep the tiller in safe working condition. Check all fasteners at frequent intervals for proper tightness.

• When servicing or repairing the tiller, do not tip the machine over or up unless specifically instructed to do so in this

manual. Service and repair procedures can be done with the tiller in an upright position. Some procedures will be

easier if the machine is lifted on a raised platform or working surface.

• Use only original equipment or authorized replacement parts.

• Never tamper with safety devices. Check their proper operation regularly.

• Do not change the engine governor setting or over-speed engine.

• Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine debris filter mounted and clean.

Children Safety

WARNING

• Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the

tiller and the tilling activity.

• Keep children out of the tilling area and under the watchful care of a responsible adult.

• Never assume that children will remain where you last saw them.

• Be alert and turn tiller off if children enter the area.

• Before and while moving backwards, look behind and down for small children.

• Never allow children to operate the tiller.

• Use extra care when operating near blind corners, shrubs, trees, or other objects that may obstruct vision.

Product Specifications

• Save all instructions

Parts & Features

Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 lb (40 kg)

Tilling Width . . . . . . . . . . . . . . . . . . . . up to 21 in (53.3 cm)

Tilling Depths . . . . . . . . . . . . . . . . . . . . . . up to 8” (20.3 cm)

Tine Diameter . . . . . . . . . . . . . . . . . . . . . . . .11 in (27.9 cm)

Gasoline Type .......Regular Unleaded/87 Octane (min.)

Gasoline Capacity . . . . . . . . . . . . . . . . . . . . 1.0 US qt. (1 L)

Engine Oil Type (API SG-SL) . . . . . . . . . . . . . . . . . . . . . . . .

10W-30 is recommended for all service temperatures.

See page (11) for additional information.

Engine Oil Capacity . . . . . . . . . . . . . 15-1/2 US oz (450 ml)

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . .OHV 4-stroke

1. Tines

2. Swing Plate

3. Wheels

4. Muffler

5. Air Filter

6. Recoil Starter Handle

7. Spark Plug / Spark Plug Wire

8. Drag Bar

9. Primer Bulb

10. Fuel Tank Cap

11. Oil Dipstick

12. Clutch Lever

13. Tine Shield

14. Outside Tine Shield

15. Wheel Height Adjust Link

Engine Displacement . . . . . . . . . . . . . . . . . . . . . . . . . 150cc

Engine Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3400 rpm

Torque Rating .... 5.75 ft-lbs gross torque per SAE J1940

Intake Valve Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.006-0.008 in. (0.15-0.20 mm)

Exhaust Valve Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.006-0.008 in. (0.15-0.20 mm)

Spark Plug Gap ..........0.024 - 0.031 in. (0.6 - 0.8mm)

Spark Plug Type ..............Torch K7RTC (Champion

C7YCC)

Wheel Size . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5” (16.5 cm)

Refer to engine manual for detailed engine specs.

Figure 1

Safety Decals

• Save all instructions

This tiller has been designed and manufactured to provide

you with the safety and reliability you would expect from an

industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions it

contains will provide you with the necessary basic knowledge

to operate this equipment safely and effectively, we have

placed several safety labels on the tiller to remind you of this

important information while you are operating the unit.

These important safety labels are illustrated and are shown

here to help familiarize you with the location and content to

the safety messages you will see as you perform normal tilling

operations. Please review these labels now. If you have any

questions regarding their meaning or how to comply with these

instructions, reread the complete safety instruction text on the

preceding pages, or contact your local dealer.

Should any of the safety labels become unreadable be-

cause of being worn, faded, or otherwise damaged during

the use of your tiller, please contact your local authorized

dealer to order replacement labels.

The safety labels are easily applied, and will act as a con-

stant visual reminder to you and others who may use the

equipment. Following the safety instructions is necessary

for safe, effective operation of your tiller.

• Gasoline is flammable. Allow engine to cool at least 2 minutes

before refueling.

• Operation of this equipment may create sparks that can start

fires around dry vegetation. A spark arrestor may be required.

The operator should contact local fire agencies for laws or

regulations relating to fire prevention requirements.

The tiller comes assembled except for a few parts. The

following instructions will help you complete the tiller assembly.

Attach the wheel assembly to the frame

1. Install the wheel assembly to the frame by removing

a hairpin cotter and at washer from one end of pivot

rod. Remove rod from frame. Align pivot holes in

wheel assembly to pivot holes in frame. Install pivot rod

and secure by reinstalling at washer and hairpin.

(See Figure 2)

Assembly

• Save all instructions

If you need assistance or find any parts missing,

CALL TOLL FREE: 1-800-737-2112.

Read and follow the assembly instructions. Do not discard

any parts or materials until the unit is assembled.

References to the right or left side of the tiller are from the

viewpoint of the operator’s position behind the tiller.

WARNING

Do not operate tiller if it is damaged or not completely and

correctly assembled.

WARNING

Before doing any assembly or maintenance to the unit,

remove the wire from the spark plug.

WARNING

Always wear ANSI compliant safety glasses with side

shields while assembling the tiller.

The following components will be found in the carton.

Quantities shown in ( ).

1. (1) Tiller

2. (1) Upper Handle Assembly

3. (1) Lower Handle

4. (4) Tines

5. (1) Wheel Assembly

6. (1) Drag bar

7. (2) Outside Tine Shields

8. (1) Tiller Operator’s Manual

9. (1) Engine Manual

10. (1) Bottle of Engine Oil

11. (1) Parts bag containing the following

a. (4) M10 x 25 mm bolts, flat washers and lock washers

for assembling lower handle.

b. (4) M8 x 25 mm saddle bolts and flat washers for as-

sembling upper handle to lower handle.

c. (4) Handle knobs, for upper handle to lower handle.

d. (2) Lynch pins for assembling outer tines.

e. (2) M10 x 50 mm bolts, (4) flat washers and (2) M10

locknuts for assembling inner tines.

f. (1) Pin, flat washer and hairpin cotter for drag bar.

g. (6) M6 x 16 bolts, lock nuts, and flat washers for install-

ing outside tine shields.

h. (1) Rope guide with nylock nut.

i. (1) Cable Ties.

1. Remove all parts and packaging components.

2. Use a utility knife to cut all 4 vertical edges and lay the

side panels flat around the tiller.

3. Remove any remaining packaging.

How to Remove Tiller from Carton

Assembly Instructions

Figure 2

Assembly Instructions (Continued)

Assembly (Continued)

• Save all instructions

Install the tines (See Figure 3)

1. Slide the tines onto the tine axle. Install the internal tines

first. Sharp edge of the front and top tines should face

down and forward to till the ground. Insert the

M10 x 50 bolt with lock nut provided to secure the

inside tines. Use one flat washer under the head of the

bolt and one under the locknut. Tighten securely.

2. For wide 21” tilling, install the outside tines in the way

that the long half of the tine tube faces towards the

inside tines. For narrow 16” tilling, install the outside

tines in a way that the short half tine tube faces towards

the inside tines.

3. Insert the Lynch pins to secure the outside tines. Install

Lynch pins so the direction of the pin is from front-

to-back and the wire loop pivots over the top of the axle.

Secure by expanding the wire loop so it extends over

and captures the end of the pin. (Fig 3)

Install the drag bar

1. Insert the drag bar into the bottom of the wheel bracket

assembly. (See Figure 4)

2. Insert the pin through the bracket and the middle

hole of drag bar and secure with flat washer and

hairpin cotter. (See Figure 4B)

Install lower handle (See Figure 5)

1. Orient lower handle with upper square holes as shown.

Align lower handle holes with respective holes in the

frame and loosely install two M10 x 25 mm bolts, lock

washers and flat washers on each side.

2. Using a wrench, tighten bolts securely on each side.

3. Remove hairpin cotter and washer from clevis pin in

lower handle. Install link using the upper hole to clevis

pin and reinstall washer and hairpin cotter. Repeat

on opposite side.

Sharp edge of tine should face down to the ground.

Figure 4

Figure 4B

Figure 5

Figure 3

Assembly (Continued)

• Save all instructions

Attach upper handle (See Figure 6,7)

1. Slide the upper handle down over the lower handle and

align the holes. Orient upper handle so clutch lever is

below handle.

2. Insert the saddle bolts into the holes as shown and

secure with at washers and handle knobs.

3. Tighten the handle knobs securely.

4. Using one cable tie, secure the control cable to

the handle as shown.

Install the outside tine shields (See Figure 8)

1. Each outside tine shield can be installed on either side

of the main tine shield.

2. Place the outside tine shield underneath the main tine

shield and align the holes.

3. Secure each outside tine shield to the main tine shield

with (3) M6 x 16 bolts washers and lock nuts.

Install the rope guide (See Figure 9)

1. Install the rope guide into the right hand section of

the upper handle as shown. Install locknut and tighten

securely. Pull engine rope and route through

the guide.

Figure 7

Figure 8

Figure 9

Figure 6

Saddle

Bolts

Handle

Knobs

Engine Preparation

• Save all instructions

Engine Oil

Engine shipped without oil. Failure to add oil will result in

serious engine damage.

A bottle of engine oil is included with your tiller. Refer

to the chart on the right for alternative oil types to use at

different temperatures. Always use a high quality detergent

oil classified “For Service, SG, SH, SJ” or higher. Do not

use special additives.

CAUTION

Always use recommended oil type. Using dirty oil or

incorrect oil type such as 2-stroke engine oil will damage

the engine.

NOTE: Engine Oil Capacity is 450 ml (15 1/2 US oz).

How to check oil level and fill to proper level

WARNING

Before checking oil, make sure engine is off, and spark

plug wire has been disconnected from spark plug.

1. Place the tiller on a level surface and make sure the

drag bar is set.

(See Figure 10)

2. Remove the oil ll cap/dipstick and wipe with clean cloth.

3. Insert dipstick into ll spout but do NOT screw in.

Remove dipstick and check oil level.

4. When oil level is full, the oil will be at upper limit on dip

stick. If oil level is near or below the lower limit, oil must

be added. (See Figure 11)

5. Add oil slowly until the oil level reaches the upper limit

of the dipstick. Use a funnel or nozzle to reduce spillage.

NOTICE

Frequently check oil level while filling. DO NOT OVERFILL.

DO NOT UNDERFILL. Running engine at improper oil

level may seriously damage engine.

6. Replace and tighten dipstick.

7. Clean up any spilled oil.

NOTE: The transmission case comes from the factory with

the proper amount and type of lubricant.

SAE

TEMP

100° F

40° C

-20

-20-30 -10

2010

60 80

Ambient Service Temperature

SAE 10W-30

SAE 30

NOTICE

*10W-30

Oil Fill Cap/Dipstick

Fuel Tank Cap

Figure 10

Oil Fill Cap/

Dipstick

Upper Limit

Lower Limit

Figure 11

Drag bar

Operation

• Save all instructions

Pre-Start Inspection

1. Make sure all safety guards are in place and all nuts and

bolts are secure.

2. Check oil level in engine crankcase. See your engine

manual for procedure and specications.

3. Inspect air cleaner for cleanliness. See your engine

manual for procedure.

4. Check the fuel supply. Fill the fuel tank no closer than 1

inch from top of tank to provide space for expansion.

Use fresh unleaded gasoline with an octane rating of 87

or higher. Do not use gasoline containing more than 10%

ethanol. Use of non-ethanol fuel is best. We recommend

the continuous use of a fuel additive /stabilizer to

counteract the effects of ethanol. These additives also

prolong the shelf life of gasoline. See your engine

manual for additional fuel recommendations.

5. Be sure spark plug wire is attached and spark plug is

tightened securely.

6. Examine underneath and around engine for signs of oil

or fuel leaks.

7. Inspect fuel hoses for tightness and fuel seepage.

8. Look for signs of engine damage.

9. Remove excessive debris from mufer area and

recoil starter.

10. Remove any debris from tines and tine shafts.

11. Move the tiller to the area of operation.

12. Check position of wheels swing plate should be in the

tilling mode position.

13. Check drag bar position.

Start the Engine

1. Press ON/OFF switch to ON position. (See Figure 12)

2. Push primer bulb 3 times. Wait 2 seconds between

each push.

3. Place left hand on upper handle. (See Figure 13)

4. Grasp starter handle and pull out slowly, until you feel

tension in the starter rope. (See Figure 13)

5. Pull rope with a rapid full arm stroke until engine starts.

6. Do not allow the starter rope to snap back. Let the

starter rope slowly rewind.

IMPORTANT: Engine is shipped from factory without oil. You

must add engine oil before starting engine.

CAUTION

Please do not start your tiller until you have read the

manual that came with your engine, and the sections in

this manual title controls, adjustments and safety. If you

have read these, follow the steps below to start your tiller.

Always perform this pre-start checklist before starting the

engine.

WARNING

Gasoline is highly ammable and must be handled with

care. Never ll the tank when the engine is hot or running.

Always move outdoors to ll tank.

WARNING

Always keep hands and feet clear of rotating machine

parts.

Figure 12

Figure 13

Operation (Continued)

• Save all instructions

Stop the Engine

1. Press ON/OFF switch to OFF position.

Operating Speed

This tiller is equipped with a fixed throttle that is set for optimum tilling performance.

Shutting Down

To stop the engine at any time, release the clutch lever and press ON/OFF switch to OFF position. To stop tines at any

time, release clutch lever.

Transport Mode and Tilling Mode

Transport mode

Fold the wheel under the engine for convenient transport.

When transporting the unit, rotate the wheel assembly

forward under the engine and move by pulling the unit

rearward. This will keep the transport wheels locked into

position. (Fig 15)

NOTE: The drag bar must be in the middle or bottom hole

for transporting.

Tilling mode

Unfold the wheel back for tilling operation. (Fig 16)

Figure 14

Figure 15

Figure 16

Clutch Lever

Operation (Continued)

• Save all instructions

NOTICE

When tilling, always pull lever completely to the handle.

Failure to do so may result in excessive drive belt wear and

premature drive belt failure.

CAUTION

This information is provided here only to introduce the

controls. Do not start the engine at this time. Starting and

operating instructions are given on page 11. Please read

this section and all operating and safety instructions before

starting your tiller.

WARNING

Do not x the clutch lever in drive position by any other

means than manually using your hand. DO NOT tie or oth-

erwise secure the lever in drive position.

NOTE: To stop the tines at any time release the clutch lever.

Clutch Lever

Engage tines by pulling the clutch lever to the handle.

Releasing the lever stops the tines and brings the tiller to a

complete stop. (See Figure 17)

Figure 17

Lever Engaged

Tilling

1. Adjust the drag bar to desired tilling depth.

WARNING

Lower the drag bar one hole at a time testing tiller

operation after each adjustment. Lowering drag bar down

too low can result in loss of control of tiller.

2. Use the upper hole in the adjustable wheel link for

shallow to medium tilling depths. Use the lower hole in

the adjustable links for deep tilling.

3. Pulling the clutch lever to the handle will engage the tines.

WARNING

Temperature of mufer and nearby areas may exceed

150˚F. Avoid these areas.

Engine, transmission and surrounding parts become

extremely hot during normal use and CAN cause

serious burn injuries if touched before the engine has cooled.

Allow engine to cool completely before touching these

surfaces.

To stop tines at any time, release CLUTCH LEVER to

neutral position. Always release CLUTCH LEVER to neutral

position AND STOP THE ENGINE before adjusting the depth of

the drag bar.

If you do not know how to do these things, read the con-

trols, adjustments and safety sections before proceeding

DANGER

IMPORTANT: Practice operating the controls and tiller with tines

out of ground before beginning to till. It is important that you

know how to use the tiller properly, keep control at all times,

stop the tines, and stop the engine if necessary. If you do not

know how to do these things, read the controls, adjustments

and safety sections before proceeding.

Adjustments

Engine should be off before adjusting any controls.

Drag Bar (See Figure 2)

Tilling depth is controlled by the height of the drag bar. To

adjust tilling depth:

1. Remove pin.

2. Adjust the drag bar to position tines at chosen tilling depth.

3. Align hole in drag bar with hole in swing plate bracket and

replace pin.

Drag Bar Up = Shallower tilling.

Place the pin in the bottom hole of the drag bar for

shallowest tilling.

Drag Bar Down = Deeper tilling.

Place the pin in the top hole of the drag bar for deepest tilling.

NOTE: The drag bar must be in the middle or bottom hole for

transporting.

Operation (Continued)

• Save all instructions

Tilling Tips

• Tilling depth will vary with ground conditions.

• When beginning to till in unbroken ground or in extremely

hard soil, set the pin in the highest hole of the drag bar

(follow instructions under Tilling section). This will allow

for shallow tilling. With the drag stake in this position,

make several light passes over the area to be tilled. Reset

for deeper depths with successive passes.

• If tiller jumps or skids uncontrollably, lower the drag

stake by placing the pin in a higher hole. This will allow

for shallower tilling. Hold firmly to the handlebars to

control sudden lurches.

• If weeds, tall grasses, vines, or other materials clog or

jam the tines, reverse the tiller to unwind vegetation.

Cultivating Tips

If you plan to use your tiller for cultivating:

• Plant rows on 20" - 22" centers for ease of turning.

• Set the drag bar with the pin in one of the higher holes.

This will allow for shallow cultivation necessary to turn

over weeds, and break up and aerate the soil.

WARNING

Do not adjust tilling depth unless clutch lever is released and engine

is turned off.

Wheel adjust links (See Figure 18 & 18B)

Use the upper hole in the adjustable wheel links for shallow to medium

tilling depths. Use the lower hole in the adjustable links for deep tilling.

WARNING

Immediately release the clutch lever if the tines jam or you

strike a foreign object. With clutch lever in neutral position,

stop the engine. Disengage the spark plug wire. When

tines have stopped, remove foreign objects and check for

damage.

WARNING

Caution must be taken in selecting tilling depth. If you attempt to

till too deeply for soil conditions, that is, with the drag bar in too

high a position, loss of control could result.

When removing material from the tines, stop engine and

remove spark plug wire rst.

Figure 18

Figure 18B

Maintenance

• Save all instructions

Maintenance Schedule

WARNING

Before performing any maintenance, turn engine off and remove the wire from the spark plug to prevent accidental starting

and serious injury.

IMPORTANT: The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the tiller as instructed in this manual, and only use genuine replacement

parts. The following table lists required periodic maintenance.

PERIODIC MAINTENANCE SCHEDULE TABLE

CAUTION

IMPORTANT NOTES about Maintenance schedule

1. Re-check tightness of all fasteners after first 2 hours of initial use

2. Change engine oil after first 5-8 hours of initial use

3. Change oil every 25 hours

4. Clean air filter every 10 hours if operating under dusty conditions.

WARNING

Use only GENUINE replacement parts. Other parts may damage the unit or result in injury.

Service Records-

Fill in dates as you complete regular

service

Before

Each Use

After

Every

10 Hours

of Use

After

Every

25 Hours

Use

After Every

50 Hours of

Use

After

Every

100 Hour

of Use

Before

Each

Season

Before

Storage

See

Note

Below

Check Engine Oil Level,

Fill to Proper Level

√ √

Clean Debris From Unit √ √ √

Lubricate All Pivot Points √ √ √

Check Fasteners for Tightness √ √

Check Drive Belts

Replace if Necessary

√ √

Check Tines for Wear or Damage

Replace if Necessary

√ √

Check Fuel Line

Replace if Necessary

√ √

Lubricate Wheel Axles √ √ √

Check Spark Plug

Replace if Necessary

√ √

Change Engine Oil √ √ √ √

2,3

Clean Air Filter

Replace if Necessary

√ √

Replace Spark Plug √ √

Clean Combustion Deposits from

Cylinder, Piston, and Valves

√

Maintenance (Continued)

• Save all instructions

Servicing the Tiller

The following information will help you make the necessary

checks and perform the procedures required to follow the

normal care recommendations made for your tiller unit. If

you prefer, your local authorized dealer can make these

checks and perform the required procedures for you.

WARNING

To prevent accidental starting:

Engine must be turned off and cool, and spark plug wire

must be removed and secured from spark plug before

checking and adjusting engine or equipment.

Change belts

1. Turn off engine. Engine must be cool completely before

proceeding.

Engine Maintenance

Engine maintenance

Refer to the engine manual included in your parts packet

for information on engine maintenance. Your engine

manual provides detailed information and a maintenance

schedule for performing the following tasks:

1. Check oil level before each use or after every 8 hours

of operation.

2. Change oil after first 5-8 hours of operation. Change oil

while engine is warm. Refill with new oil of

recommended grade.

3. Check spark plug yearly or every 25 hours of operation.

4. Service air cleaner.

5. Keep engine and parts clean.

6. Check engine and equipment often for loose nuts and

bolts, keep these items tightened.

2. Remove spark plug wire and secure from spark plug.

3. Remove the front belt cover.

• Remove the belt from the engine pulley:

- Remove the four engine plate-to-frame bolts.

- Slightly lift the engine and engine plate as an

assembly.

- Slide the belt free of the engine pulley.

- Remove the belt from the front pulley.

• Install new belt:

- Place belt around transmission pulley in groove.

- Place belt onto engine pulley in groove.

- Place backside of belt around idler pulley and belt

guides.

- Reinstall and tighten four engine plate bolts.

- Slowly pull engine rope and observe belt

movement to verify correct routing of belt.

- Reinstall front belt cover.

4. Attach spark plug wire.

5. Follow Operating Instructions- start the engine and

operate the clutch lever.

WARNING

The tines should not rotate with the engine running and the

drive lever not engaged.

Maintenance

wire

tab

Check or fill engine crankcase

IMPORTANT: Engine is shipped from factory without oil. You

must add engine oil before starting engine.

1. Add oil according to engine manual. Do not overfill.

Use a clean, high quality detergent oil. Do not mix oil

with gasoline. Oil level must be full. Check the oil level

by removing oil fill plug.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

Lubrication

Proper lubrication of moving mechanical parts is critical for

proper care and maintenance. Oil the moving parts at 10

hour intervals using 30 weight oil.

Clean tine axle shaft

1. Turn off engine. Engine must be cool.

2. Remove spark plug wire and secure from spark plug.

3. Tip the tiller backward. Block the tiller in position so that

it rests on the upper handle and the tines are exposed.

4. Remove all vegetation, string, wire, and other material

that may have accumulated on the axle between the

inside set of tines and the seal cover on the

transmission housing.

5. Tip the tiller back to a level position.

6. Replace spark plug wire.

How to Prepare for Storage

WARNING

Never store the tiller indoors with fuel in the fuel tank.

Never store in an enclosed, poorly ventilated area where

fumes could reach an open ame, a spark or a pilot light as

on a furnace, water heater or clothes dryer. Allow engine to

cool before storing unit.

WARNING

Do not remove gasoline while inside a building, near a re,

or while you smoke. Gasoline fumes can cause an explo-

sion or a re.

NOTE: A yearly checkup or tune-up at an authorized service

center will make sure that the tiller will provide maximum

performance for the next season.

When the tiller is put in storage for thirty days or more, the

following steps should be followed to make sure the tiller is in

good condition the next season. To prevent fuel gum deposits

and corrosion in the unit’s carburetor and fuel system, it is

highly recommended to use a fuel additive/stabilizer formulated

for ethanol fuels. Follow the stabilizer manufacturer’s

instructions. Run the engine for at least 5 minutes after adding

stabilizer.

1. Let the engine run until it is out of gasoline. Remove

carburetor screw from bowl and drain fuel. Tilt unit

slightly to remove all fuel. Replace screw. (Figure 19)

2. Change the oil by following instructions under “How to

Change the Oil.”

3. Remove the spark plug from the cylinder. Pour one

ounce (1 oz liq. US / 30 ml) of oil into the cylinder.

Slowly pull the recoil-start handle so that the oil will

protect the cylinder. Install a new spark plug in the

cylinder. Pull starter handle slowly a few times to

Maintenance (Continued)

• Save all instructions

You may have further questions about assembling, operating, or maintaining this TILLER. If so, you can contact our

Technical Service Department at 1-800-737-2112 (English only).

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

6700 Wildlife Way

Long Grove, IL 60047

Technical Service

When contacting the Technical Service Department, have ready:

• Your Name

• Your Address

• Date Code on Product

• Your Phone Number

If you need assistance or have any questions, CALL

TOLL FREE: 1-800-737-2112.

distribute oil. Pull recoil handle slowly until resistance is

felt. This will close the cylinder valves.

WARNING

DO NOT attach spark plug wire to spark plug when

storing unit.

4. Clean tiller. Remove all dirt, leaves, debris, grease, etc.

from the tiller - including cylinder cooling fans, recoil

starter cover holes, under fuel tank, and under mufer.

5. Check the tiller for worn or damaged parts. Have

damaged parts replaced if necessary.

6. Tighten any loose hardware.

7. Apply lubrication as directed in Maintenance section.

8. Put the unit in a building that has good ventilation.

9. Cover the tiller with a breathing material.

Figure 19

Remove carburetor screw from

bowl and drain fuel. Replace screw.

PROBLEM POSSIBLE CAUSE(S) SOLUTION(S)

Engine difficult to start 1. Out of fuel

2. Engine Switch Off

3. Engine is not primed

4. Spark plug wire disconnected

5. Fouled spark plug

6. Dirty Carburetor

7. Clogged air filter

8. Contaminated Fuel

1. Add fresh fuel

2. Turn engine switch on

3. Push primer 3 times.

4. Attach spark plug wire to spark plug

5. Remove spark plug. Inspect. Replace if

necessary

6. Take unit to an authorized service center

for Carburetor cleaning

7. Remove and clean air filter

8. Drain fuel tank. Clean fuel tank. Fill with

fresh fuel

Engine Problems

Engine smokes excessively

Engine runs very “rough”

Engine runs erratically

Engine cannot maintain full speed

1. No Engine Oil

2. Engine oil not at proper level

3. Fouled spark plug

4. Clogged air filter

5. Contaminated Fuel

6. Carburetor out of adjustment

1. Add engine oil

2. Check engine oil. Add or drain engine oil if

necessary

3. Remove spark plug. Inspect. Replace if

necessary

4. Remove and clean air filter

5. Drain fuel tank. Clean fuel tank. Fill with

fresh fuel

6. Take unit to an authorized service center

for Carburetor adjustment

Excessive vibration / noise 1. Loose parts

2. Engine problems (above)

1. Tighten all fasteners

2. Refer to engine solutions (above)

Tines will not rotate 1. Debris interfering with tines

2. Tines loose

3. Damaged drive belts

1. Remove debris from around tines

2. Replace tine bolts and nuts

3. Replace drive belts

Tines continue to rotate when

lever is not engaged

1. Damaged drive belts 1. Replace drive belts

Engine will not stop Faulty switch Replace switch

Tines will not cut properly 1. Damaged or worn tines

2. Tines assembled incorrectly

1. Replace tines

2. Refer to “Install the Tines” Section

Frequent engine stalling 1. Excessive tilling speed / depth

2. Engine problems (above)

1. Till at a moderate pace. Make multiple

passes.

2. Refer to engine solutions (above)

Troubleshooting

• Save all instructions

Warranty

• Save all instructions

Always specify model number when contacting the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied. MAT Engine Technologies, LLC warrants this Tiller and any parts thereof,

to be free from defects in material and workmanship for two years (90 days for commercial use) from the date of first purchase from

an authorized dealer, provided that the product has been properly maintained and operated in accordance with all applicable instruc-

tions. This warranty is extended only to the original retail purchaser. The bill of sales or proof of purchase must be presented at the time

a claim is made under this warranty. This warranty does not cover industrial or rental usage, nor does it apply to parts that are not in

original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack of proper

maintenance, tampering, or alteration. Exceptions to the standard warranty period would be normal wear items such as cutting blades,

string heads, earth auger blades, air filter, and spark plugs which are only covered for 60 days against defects in material or workman-

ship. Travel, handling, transportation, and incidental costs associated with warranty repairs are not reimbursable under this warranty

and are the responsibility of the owner. To the full extent allowed by the law of the jurisdiction that governs the sale of the product, this

express warranty excludes any and all other expressed warranties and limits the duration of any and all implied warranties, including

warranties of merchantability and fitness for a particular purpose to two years from the date of first purchase, and MAT Engine Technol-

ogies, LLC’s liability is hereby limited to the purchase price of the product and MAT Engine Technologies, LLC shall not be liable for any

other damages whatsoever including indirect, incidental, or consequential damages. Some states do not allow limitation of how long an

implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation of damages may not

apply to you. This warranty provides the original purchaser with specific rights.

For information regarding those rights, please consult the applicable state laws.

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

6700 Wildlife Way

Long Grove, IL

60047

Powermate® ROTARY TILLER Limited Warranty

If you have any questions regarding your warranty coverage, you

should contact METL customer service:

If you need assistance or have any questions, CALL

TOLL FREE: 1-800–737-2112

The Engine Emissions Control System Warranty is provided by the engine manufacturer, included with this product and administered by

MAT Engine Technologies, LLC.

La page charge ...

Powermate PFTT142 Manuel utilisateur

Marque: Powermate

Modèle: PFTT142

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Ce manuel convient également à

SFTT142

Télécharger le PDF

rapport

dans d''autres langues

English: Powermate PFTT142 User manual
español: Powermate PFTT142 Manual de usuario

Powermate PFTT142 Manuel utilisateur

Ce manuel convient également à

Powermate PFTT142 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents