Paradigm Surround 1 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Owner’s Manual
PARADIGM
SURROUND 1
PARADIGM
SURROUND 3
RECYCLING AND REUSE GUIDELINES (Europe)
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we
would like to notify you that our speakers may contain regulated materials which, upon disposal, require special reuse and recycling
processing. For this reason Paradigm Electronics Inc. (the manufacturer of Paradigm speakers and Anthem electronic products) has
arranged with its distributors in European Union member nations to collect and recycle this product at no cost to you. To find your
local distributor please contact the dealer from whom you purchased this product or go to our website at www.paradigm.com.
Please note that only the product falls under the WEEE directive. When disposing of packaging and other shipping material we
encourage you to recycle through the normal channels.
To ensure proper installation and enjoy all of the exceptional sound
these speakers are designed to provide, please read this manual
and follow all instructions. If you have further questions contact your
Authorized Paradigm Dealer or visit the Q&A page on our website at
www.paradigm.com.
220118
Paradigm DOES NOT supply hardware for
mounting speakers to the wall. Use screws
which are appropriate for wall type and weight
of speakers.
If installing into drywall, install into 1/2˝ (13 mm)
or 5/8˝ (16 mm) drywall only. Screws must be long
enough to go through anchor bolts (not supplied).
NON-LIABILITY: We are aware that the wall mounting
assemblies sold separately, for use with Paradigm Surround
speakers could be used for purposes and in ways other
than those for which they were intended. The manufacturer,
distributor, retailer and their respective agents cannot
be held responsible or liable for injuries or property
damage direct, indirect, or consequential arising
from the use of or inability to use these products safely
and properly. Every effort has been made to provide accurate,
error-free installation instructions. Paradigm Electronics
Inc. disclaims liability for difficulties that may arise from
the misinterpretation of information contained in these
instructions.
IMPORTANT: Read before wall mounting your surround speakers.
IMPORTANT: Read before placing surround speakers on flat surface.
For stability, bumper pads (included) must be used
when placing surround/rear speakers on a flat
surface. Please see the section on “Placement:
Surround / Rear Speakers” for more info.
Thank you!
Thank you for choosing a Paradigm Surround speaker. You are about
to hear the difference that sonically accurate speakers make in your
audio/home theater system! They are the product of countless hours of
comprehensive research and development and will reward you with
truly exceptional sound for many years.
To ensure proper installation and enjoy all of the exceptional sound
these speakers are designed to provide, please read this manual
and follow all instructions. If you have further questions contact your
Authorized Paradigm Dealer or visit the Q&A page on our website at
www.paradigm.com.
paradigm.com
1
Applying Rubber Pads ................................................................... 2
Your New Speakers ....................................................................... 3
Preventing Speaker Damage ........................................................ 4
Room Acoustics ............................................................................ 6
Placement: Surround / Rear Speakers ........................................ 7
Wiring .............................................................................................. 8
Connection ..................................................................................... 9
Fine Tuning ................................................................................... 10
Troubleshooting Guide ............................................................... 11
Limited Warranty ......................................................................... 12
TABLE OF CONTENTS
2
APPLYING RUBBER PADS
Rubber pads are included in the hardware package with your
speaker. For stability, apply rubber pads as shown when placing
the surround on a flat surface.
Paradigm Surround 1
Paradigm Surround 3
paradigm.com
3
Break-In
Although Paradigm Surround speakers sound great “out of the carton,”
they will sound even better when broken in. Allow them to operate for
several hours before you listen critically.
High-frequency drivers use ferro-fluid that can thicken at temperatures
below 10° C (50° F). If your speakers have been transported or stored in
the cold, let them warm to room temperature before use.
Cleaning
Do not use a strong or abrasive cleaner on your speakers. Clean
them with a damp soft cloth, but do not get them wet. Do not place
wet objects, such as drinking glasses or potted plants, on top of the
speakers. If allowed to soak in, even a small amount of water may
permanently damage the speaker enclosure.
YOUR NEW SPEAKERS
4
To prevent damage to your speakers, please read the following
guidelines before making any connections.
Amplifier Distortion — The #1 Culprit!
Amplifier distortion is the principle cause of speaker damage. When
listening at higher volume levels, your amplifier may run out of clean
power and begin to produce a distorted signal if levels are increased any
further. This will damage any brand of speaker very quickly. (See your
Authorized Paradigm Dealer for amplifier recommendations).
More Powerful Amplifiers are Safer
When choosing an amplifier, always select an amplifier with a power
rating greater than that of the speaker. Using a 100W per channel
amplifier on a 50W speaker allows the amplifier adequate headroom in
order to provide a distortion free signal. Conversely, using a 40W per
channel amplifier on a 50W speaker limits the amplifier’s headroom. This
causes the amplifier to enter its distortion level much sooner, potentially
damaging the speaker.
Volume Control
Do not be fooled by the Volume Control of your receiver/preamplifier.
It only adjusts listening level it is not a “power-output” dial. The
amount of amplifier power actually used at a given Volume Control
setting depends solely on the nature of the music you are listening
to. At a given Volume Control setting a quiet section of music will use
less amplifier power than a loud section. With typical pop-rock, jazz or
large scale classical music the rated output power of many receivers/
amplifiers is often reached when the Volume Control is between the
“11” and “1” o’clock settings (with bass/treble and loudness controls
not used —otherwise rated power may be reached at even lower
Volume Control settings).
Remember, all amplifiers produce distortion when operated beyond
their rated output power. The resulting distortion will damage all
speakers! Exercise caution! If you listen at loud levels, be careful to
listen for the point of audible distortion—if the speakers begin to sound
distressed, turn the Volume Control down or your speakers and/or
amplifier(s) will be damaged! This type of damage constitutes abuse
and is not covered by the warranty. If louder volumes are desired,
obtain a more powerful amplifier.
PREVENTING SPEAKER DAMAGE
paradigm.com
5
There is a Limit!
Although more powerful amplifiers are safer, there is a point at which
you could have more power than the speaker can handle. At that point
you will overpower the speaker and damage it. Exercise caution! At loud
levels do not increase bass/treble controls from zero and ensure that
all loudness/contour/bass EQ buttons are off (otherwise rated output
power will be reached at lower volume control settings). If you listen at
loud levels, watch for excessive visible cone excursion (grille movement)
from the woofer—then turn the Volume Control down.
The Right Amount of Power
A power-range rating is given as a guide to indicate the approximate
minimum and maximum power input of your Paradigm speakers.
Amplifiers that exceed your speaker’s power-range rating are
recommended. Their greater power reserves provide better sound.
However, exercise caution! Use the speakers within their power-range
rating to prevent damage (keep listening levels below the point of
excessive woofer cone excursion).
6
Paradigm Surround speakers are designed to provide exceptional sound
in a wide variety of domestic settings. However, it is important to note
that listening room construction, dimensions and furnishings all play a
part in the quality of sound you will ultimately achieve. Your listening room
will impose its own character on the performance capabilities of any speaker
system. The extra care you take in correctly positioning the speakers
will result in greater listening enjoyment. Keep the following guidelines in
mind when deciding on the best speaker placement:
Mid and high frequencies are affected by the amount of soft furnishings
in your room curtains, carpets, sofas, wall coverings, etc. An
excess of such items can result in a somewhat dull sound. The
same room without any soft furnishings can produce an overall bright
sound. The typical quantity of soft furnishings found in most living
environments provides the right acoustic characteristics to allow the
speakers to sound balanced;
Concrete floors and walls tend to aggravate low-frequency standing
wave problems and are less preferred;
Rooms where height, width and length are similar should be
avoided as they can exhibit significant low-frequency standing wave
problems. This may result in reduced clarity. If no other room is possible,
experiment with speaker placement to minimize acoustic problems.
ROOM ACOUSTICS
paradigm.com
7
5.1 Surround Speaker Placement
SURROUND SPEAKER PLACEMENT
7.1 Surround Speaker Placement
90˚
135˚
150˚
90˚
110 ˚
135˚
150˚
110 ˚
90˚
135˚
min. 2 ft. min. 2 ft.
150˚
90˚
90˚ 90˚
110 ˚
135˚
150˚
110 ˚
110 ˚110 ˚
110 ˚
120˚
110 ˚
120˚
5.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
7.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
5.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
7.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
90˚
135˚
150˚
90˚
110 ˚
135˚
150˚
110 ˚
90˚
135˚
min. 2 ft. min. 2 ft.
150˚
90˚
90˚ 90˚
110 ˚
135˚
150˚
110 ˚
110 ˚110 ˚
110 ˚
120˚
110 ˚
120˚
5.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
7.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
5.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
7.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
PLACEMENT: Surround / Rear Speakers
8
WIRING
For optimum sound, the use of high quality speaker cable is essential.
The chart below identifies the minimum gauge requirements for various
lengths. See your Authorized Paradigm Dealer for recommendations.
MINIMUM GAUGE REQUIREMENTS
LENGTH DIAMETER GAUGE
Under 4.5 m (15 ft) 1.3 mm (0.05 in) 16 awg
Under 9 m (30 ft) 1.6 mm (0.06 in) 14 awg
Over 9 m (30 ft) 2.0 mm (0.08 in) 12 awg
Turn your amplifier(s) OFF before connecting your
speakers. This will avoid damage which could
result from accidental shorting of speaker cables.
paradigm.com
9
Your speakers’ binding posts can be used with banana, pin or spade
connectors, as well as with bare wire. Tighten the posts firmly by hand
but do not over tighten!
Correct polarity (or phase) is critical for proper soundstage imaging and
bass performance. Connect one speaker at a time to ensure proper
connection of every channel. The red (+) amplifier terminal must be
connected to the red (+) speaker terminal. The same applies to the black (–)
terminals. Make sure all wires are firmly fastened. Repeat this connection
procedure for each speaker in your system.
NOTE: If you hear a distinct lack of bass and a dislocated stereo image then
one or more of your speakers may be connected out of phase (polarity is
reversed). Re-check to ensure that each speakers’ cable is connected with
correct polarity: red (+) to red (+) and black (–) to black (–).
-+
CONNECTION
10
Once you have your speakers positioned in the room and have set
speaker
distances and calibrated speaker levels through your Audio/Video
Processor or A/V Receiver it’s time for a little fine tuning.
Since Paradigm speakers provide exceptional performance in a variety of
room settings, fine tuning is simply a matter of making slight adjustments
(if necessary) to their placement in the room.
To fine tune your surround/rear speakers, please follow the illustrations
in the “PLACEMENT: Surround/Rear Speakers” section.
FINE TUNING
paradigm.com
11
Make sure receiver, preamp or amplifier is
plugged in and turned on. Check power
outlet at the wall is working. Are headphones
plugged in, or is system on Mute? Re-check
all connections.
One or more speakers may be connected
out of phase (their polarity is reversed). Re-
check to ensure that each speaker’s cable is
connected with correct polarity: red (+) to red
(+) and black (-) to black (-).
Check your balance. Check that all power
cords are properly plugged in and functioning.
Swap a non-working speaker with one that
works to determine if the problem is with
the speaker or something else (i.e. wiring,
amplifier).
No Sound
Lack of
Bass or
Dislocated
Image
No Sound
from One
or More
Speakers
TROUBLESHOOTING
12
The Paradigm speakers covered in this manual are warranted to be
and remain free of manufacturing and/or material defects for a period of
five (5) years from the date of original purchase. Within the time period
specified, repair, replacement or adjustment of parts for manufacturing
and/or material defects will be free of charge to the original owner.
Thermal or mechanical abuse/misuse is not covered under the
Paradigm warranty.
Limitations:
Warranty begins on date of original retail purchase from an Authorized
Paradigm Dealer only. It is not transferable;
Warranty applies to product in normal home use only. If product is
subjected to any of the conditions outlined in the next section, warranty
is void;
Warranty does not apply if the product is used in professional or
commercial applications.
Warranty is Void if:
The product has been abused (intentionally or accidentally);
The product has been used in conjunction with unsuitable or faulty
equipment;
The product has been subjected to damaging signals, derangement
in transport, mechanical damage or any abnormal conditions;
The product (including cabinet) has been tampered with or damaged
by an unauthorized service facility;
The serial number has been removed or defaced.
LIMITED WARRANTY
paradigm.com
13
Owner Responsibilities:
Provide normal/reasonable operating care and maintenance;
Provide or pay for transportation charges for product to service facility;
Provide proof of purchase (your sales receipt given at time of purchase
from your Authorized Paradigm Dealer must be retained for proof-of-
purchase date).
Should servicing be required, contact your nearest Authorized Paradigm
Dealer, Paradigm Electronics Inc. or Import Distributor (outside the U.S.
and Canada) to arrange, bring in or ship prepaid, any defective unit. Visit
our website, www.paradigm.com for more information.
Paradigm Electronics Inc. reserves the right to improve the design of
any product without assuming any obligation to modify any product
previously manufactured.
This warranty is in lieu of all other warranties expressed or implied, of
merchantability, fitness for any particular purpose and may not be extended
or enlarged by anyone. In no event shall Paradigm Electronics Inc., their
agents or representatives be responsible for any incidental or consequential
damages. Some jurisdictions do not allow limitation of incidental or
consequential damages, so this exclusion may not apply to you.
Retain this manual and your sales receipt for proof of warranty term and
proof of purchase.
NOTES
Manuel d’utilisateur
PARADIGM
SURROUND 1
PARADIGM
SURROUND 3
DIRECTIVES EUROPEENNES SUR LE RECYCLAGE ET LE TRAITEMENT
DES DECHETS
Dans le respect de la directive WEEE (Waste Electrical & Electronic Equipment) mise en place par les institutions Européennes à
compter du 13 Août 2005, nous souhaitons vous informer que nos enceintes peut contenir des matières devant faire l’objet d’une
procédure de recyclage ou de traitement approprié des déchets. Dans cette optique, Paradigm Electronics Inc (fabricant des
enceintes Paradigm et des électroniques Anthem) avec ses Distributeurs agréés dans l’Union Européenne, ont mis en place une
procédure de collecte et de retraitement gratuite. Pour en savoir davantage sur cette procédure veuillez contacter votre revendeur,
ou notre Distributeur dans votre pays (vous en obtiendrez les coordonnées sur simple demande ou en consultant notre site internet
www.paradigm.com.
Notez que seul le produit fini est concerné par cette directive et ses obligations. S’agissant de son emballage et de ses accessoires de
transport nous vous recommandons de les recycler selon les procédures mises en place par votre commune ou votre département.
Pour une installation appropriée, et pour profiter d’un son exceptionnel,
veuillez lire le présent manuel et suivre toutes les instructions. Pour
toute autre question, contactez un revendeur Paradigm autorisé
ou consultez la page Questions-Réponses de notre site Web au
www.paradigm.com.
220118
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Paradigm Surround 1 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues