Esoteric K-01 Le manuel du propriétaire

Marque: Esoteric

Modèle: K-01

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Ce manuel convient également à

K-03

D01126221E

01/ K

Super Audio CD/CD Player

OWNER’S MANUAL .................... 4

MODE D’EMPLOI ...................... 28

MANUAL DEL USUARIO ........... 52

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A

SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN

REPAIRED.

< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

< Do not expose this apparatus to drips or splashes.

< Do not place any objects filled with liquids, such as vases, on the

apparatus.

< Do not install this apparatus in a confined space such as a book

case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

< The apparatus should be located close enough to the AC outlet so

that you can easily reach the power cord plug at any time.

< The mains plug is used as the disconnect device, the disconnect

device shall remain readily operable.

< Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a product

must be plugged into an AC outlet that has a protective grounding

connection.

< If the product uses batteries (including a battery pack or installed

batteries), they should not be exposed to sunshine, fire or

excessive heat.

< CAUTION for products that use replaceable lithium batteries: there

is danger of explosion if a battery is replaced with an incorrect type

of battery. Replace only with the same or equivalent type.

< Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

“DSD” is a registered trademark.

“Super Audio CD” is a registered trademark.

This product incorporates copy protection technology that is protected by

U.S. patents and other intellectual property rights of Rovi Corporation. The

use of Rovi Corporation's copy protection technology in the product must be

authorized by Rovi Corporation.

Reverse engineering and disassembly are prohibited.

Microsoft, Windows XP, Windows Vista and Windows 7 are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or

other countries.

Apple, Macintosh and Mac OS X are trademarks of Apple Inc., registered in the

U.S. and other countries.

MEXCEL is a registered trademark of Mitsubishi Cable Industries, Ltd. in Japan

and other countries.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S. and

other countries.

Other company names and product names in this document are the

trademarks or registered trademarks of their respective owners.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

For U.S.A.

Laser :

Type : SLD6163RL-G

Manufacturer : SONY CORPORATION

Laser output : Less than 1mW on the objective lens

Wavelength : 785±15 nm (CD)

655±10 nm (Super Audio CD)

China RoHS

< The information in the following table is only applicable to products for sale in the People’s Republic of China.

< The products sold in the European area are manufactured in accordance with the European RoHS Directive.

Contents

Thank you for choosing Esoteric. Read this manual carefully to

get the best performance from this unit.

Before Use ....................................................5

Discs .........................................................6

Remote Control Unit ..........................................7

Connections ..................................................8

Identifying the Parts (Main Unit) ..............................10

Identifying the Parts (Front Panel Display) ..................... 11

Identifying the Parts (Remote Control Unit) ...................12

Playback .....................................................14

Programmed Playback .......................................16

Repeat playback .............................................17

Changing the Display Mode ..................................17

D/A Converter Mode ........................................18

Connecting with a Computer ................................18

Changing Settings ...........................................20

Setting Items ................................................20

Display Dimming ............................................23

Volume Control .............................................24

Restoring Factory Default Settings ............................24

Troubleshooting .............................................25

Specifications ................................................26

Rear Panel Layout ............................................27

English

Before Use

Read this before attempting any operations.

What’s in the box

Confirm the supplied standard accessories.

Remote control unit (RC-1156) x 1

Batteries (AA) x 2

Power cord set x 1

Felt pads x 3

< To protect the supporting furniture surface, you may stick these

felt pads to the bottom of the metal feet (see below).

Owner’s manual (this document) x 1

< Keep this manual in a safe place for future reference.

Warranty card x 1

Placement of the unit

< High-quality hardened tool steel is used for the pin-point feet,

securely attached to the bottom of the unit. Although the outer

feet may appear loose, the weight of the unit causes them to

become firm and secure. The design effectively damps and reduces

vibration.

To protect the supporting furniture surface, you may stick the felt

pads supplied with the unit to the bottom of the metal feet.

Bottom plate

of the unit

Pin-point foot

Steel

foot

Cover foot Cover foot retaining screws

< Place the unit in a stable location near the audio system that you

will use.

< Choose the installation location of your unit carefully. Avoid placing

it in direct sunlight or close to a source of heat. Also avoid locations

subject to vibrations and excessive dust, heat, cold or moisture.

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

Make sure there is at least 8"/20cm of space above and at least

2"/5cm of space on each side of the unit. Do not place anything

on top of the unit.

< Do not place the unit on an amplifier or receiver or any other

device that generates heat.

< When the unit is turned on, switching on the TV may cause lines

to appear on the TV screen, depending on the condition of the

electric waves of the TV broadcast. This is not malfunction in the

unit or the TV. If you see such lines, keep this unit well away from

the TV set.

CAUTION

< Do not move the unit during playback.

During playback, the disc rotates at high speed. Do not lift or

move the unit during playback. Doing so may damage the disc

or the unit.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Do not open the cabinet as this might result in damage to the

circuitry or cause electric shock. If a foreign object should get into

the unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank on the cord.

< Always remove the disc before relocating or moving this unit.

Moving the unit with a disc inside could cause malfunction.

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth or

use diluted mild liquid soap. Allow the surface of the unit to dry

completely before using.

For safety, disconnect the power cord from the socket before

cleaning.

< Never spray liquid directly on this unit.

< Do not use thinner, benzene or alcohol as they could damage the

surface of the unit.

< Avoid allowing rubber or plastic materials to touch this product for

long periods of time, because they could damage the cabinet.

Beware of condensation

When the unit is moved from a cold to a warm place, or used after a

sudden temperature change, there is a danger of condensation on

the lens of CD/SACD player; vapor in the air could condense on the

internal mechanism, making correct operation impossible. To prevent

this, or if this occurs, leave the unit turned on for one or two hours.

Then the unit will stabilize at the temperature of its surroundings.

Discs

Discs that can be played on this unit

CDs that bear the “COMPACT disc DIGITAL AUDIO” logo.

< 12cm (4.7") or 8cm (3.15") discs

< Linear PCM digital audio

Audio CDs are divided into tracks.

Super Audio CDs that bear the “Super Audio CD” logo.

< Single layer, dual layer or hybrid layer

< 12cm (4.7") discs

< Digital audio (DSD)

Super Audio CDs are divided into tracks.

CD-R and CD-RW discs that have been correctly recorded

in the audio CD format (CD-DA) and finalized.

This unit can play these types of discs without an adapter. It cannot

play any other type of disc.

Playback of any other type of disc could cause loud noise and

damage to speakers as well as harm hearing. Never play back any

other type of disc.

< The logo should be on the disc label or the CD jacket.

< DVDs, Video CDs, DVD-ROMs, CD-ROMs and similar types of discs

cannot be played on this unit.

< Copy-protected discs and other discs that do not conform to the

CD standard might not play correctly in this player. If you use such

discs in this unit, TEAC CORPORATION and its subsidiaries will not

be responsible for any consequences or guarantee the quality of

reproduction. If you experience problems with such non-standard

discs, you should contact their issuers.

< Discs created by a CD recorder must be finalized before use with

this unit. If you are uncertain about the handling of a CD-R or

CD-RW disc, please contact the seller of the disc directly.

Depending on disc quality and recording conditions, playback of

some discs might not be possible. Please see the manual for the

device that you used to create the disc.

CAUTION

< Do not play any disc that is warped, deformed or damaged.

Playing such discs could cause irreparable harm to the playing

mechanisms.

< Printable CD-R and CD-RW discs are not recommended because

their label sides could be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do not

use any protective coating sprays.

< Never use a stabilizer. Using commercially available CD stabilizers

with this unit will damage the mechanisms and cause them to

malfunction.

< Do not use irregularly-shaped discs (octagonal, heart-shaped,

business card size, etc.). CDs with these shapes could damage the

unit.

Handling precautions

< Always insert the disc into the disc tray with the label side up. Only

one side of a Compact Disc can be played or used for recording.

< To remove a disc from its storage case, press down on the center

of the case and lift the disc out, holding it carefully by the edges.

How to remove the disc How to hold the disc

Storage precautions

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high-temperature

and humidity for extended periods. Long exposure to high

temperatures will warp discs.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they

are not stored in locations where they will be exposed to direct

sunlight. They should also be kept away from sources of heat, such

as radiators and heat-generating electrical devices.

Maintenance

< If a disc becomes dirty, wipe its surface radially from the center

hole outward towards the outer edge with a soft, dry cloth.

< Never clean discs using chemicals such as record sprays, antistatic

sprays and fluids, benzene and thinner. Such chemicals will do

irreparable damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a disc, read the

precautions supplied with the disc or contact the disc manufacturer.

English

Remote Control Unit

The included remote control allows this unit to be operated from a

distance.

Point the remote control unit at the main unit’s remote sensor

within 23feet/7m of the main unit.

Remote sensor

23 feet/7m

< Depending on the angle, reception might be difficult. Use the

remote control from directly in front of the unit as much as

possible.

< Even if the remote control unit is used within its effective range,

operation by remote control might be impossible if there are any

obstacles between the unit and the remote control.

< If direct sunlight or strong artificial illumination shines on the

remote sensor, the remote control might not function.

< If the remote control unit is operated near other devices that

generate infrared rays, or if other remote controls that use infrared

rays are operated near the unit, this unit might operate incorrectly.

The other devices might also operate incorrectly.

Battery Installation

Use a Philips screwdriver to remove the cover from the bottom of

the remote control, and pull out the battery case. Insert two AA

batteries in the correct +/_ orientations, reinsert the case and

close the cover.

Battery Replacement

If the operating range required between the remote control unit and

main unit decreases, the batteries are exhausted. In this case replace

the batteries with new ones.

For more information about collection of batteries, please contact

your local municipality, your waste disposal service or the point of sale

where you purchased the items.

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading

to fire, injury or the staining of nearby things. Please read and

observe the following precautions carefully.

< Be sure to insert the batteries with correct positive (+) and

negative (_) orientations.

< Use batteries of the same type. Never use different types of

batteries together.

< Both rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

< If the remote control will not be used for a long time (more than a

month), remove the batteries to prevent them from leaking.

< If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

< Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

< Do not heat or disassemble batteries. Never throw batteries into

fire or water.

< Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

< Never recharge a battery unless it is confirmed to be a

rechargeable type.

Connect one of

these cables.

The polarity of XLR terminal

can be set to pin # 2 HOT or

pin # 3 HOT (page 22).

Digital output can be set to

on or o (page 22).

Stereo amplier

Wall socket

LLRR

Computer

LINE IN

WORD SYNC OUT

Master clock

generator

(G-01,G-02, etc.)

DIGITAL OUT

(COAXIAL)

DIGITAL IN

(COAXIAL)

Digital device

DIGITAL OUT

(OPTICAL)

Digital device

or computer with

S/PDIF digital audio

outputs

Amplier or digital audio

device (CD recorder, MD

deck, etc.)

XLR cable

RCA audio cable

USB cable

RCA digital coaxial cable

BNC coaxial cable

Optical digital cable

Supplied power cord

Connections

After all connections are complete, connect the power cord’s plug to the AC wall socket.

< Read the instructions of each device that you intend to use with this unit.

< Be sure to connect each plug securely. To avoid hum and noise, do not bundle the connection cords.

English

Analog audio output terminals

Use either the XLR or RCA terminals for 2-channel analog stereo

output.

Use commercially available XLR or RCA audio cables.

XLR: Use balanced XLR audio cables

RCA: Use RCA audio cables

Connect the R terminal on this unit to the right (R) terminal of the

amplifier and the L terminal on this unit to the left (L) terminal of

the amplifier.

< Analog audio output can be set to on or off and the polarity

of the XLR terminal can be set to pin # 2 HOT or pin # 3 HOT

(page22).

< You can set the XLR output gain separately (page22). If the sound

is distorted when set to “+6dB”, change the setting to “0dB”.

USB input terminal

Inputs digital audio from a personal computer.

Connect to the USB port of a personal computer using a

commercially available USB cable.

< Before connecting to a computer, read the instructions on

pages18 – 19.

Digital audio input terminals

Inputs digital audio.

Connect to the digital output terminals of digital devices

or to PC cards with S/PDIF digital audio outputs using a

commercially available cable.

COAXIAL: Use RCA digital audio cables

OPTICAL: Use optical digital audio cables (TOS Link)

Digital audio output terminal

This terminal outputs digital audio signals from a currently

playing CD or a device that is connected to the digital audio

input terminals of this unit.

Connect to the digital input terminals of amplifiers

or digital audio devices such as CD recorders, using a

commercially available RCA digital audio coaxial cable.

< This terminal cannot output digital audio from Super Audio CDs.

< Digital output can be set to “OFF”, “CD” or “THRU” (page22).

< When recording on a connected device, you cannot record

digitally from copy-protected digital audio sources. You can

record these signals as analog audio.

WORD SYNC connector

This allows the use of an externally-generated word clock

connection.

Connect to a WORD SYNC OUT terminal of an external

word clock generator or other equipment that has a word

clock output using a commercially available BNC coaxial

cable.

SIGNAL GND terminal

Connection of this terminal with the ground terminal of another

chassis may improve sound quality.

< Note that this is NOT an electrical safety ground (earth).

Power cord

Connect the power cord to the power cord receptacle.

After all other connections are complete, connect the

power cord's plug to the AC wall socket.

Do not use any power cord other than an authentic Esoteric

product. Doing so could cause fire or electric shock.

Unplug the power cord when you are not going to use the

unit for several weeks.

At Esoteric, we use Esoteric MEXCEL stressfree cables for

reference.

For detailed information, access the following website.

http://www.esoteric.jp/products/esoteric/accessory/indexe.html

Identifying the Parts (Main Unit)

POWER

Press this button to turn the unit on and off.

The blue indicator lights when the unit is turned on.

WORD indicator

Shows word synchronization status.

Blinks when a word clock signal is received.

Lights continuously when a word clock signal is locked.

MODE (source select)

When playback is stopped, each time the MODE button is

pressed, the source changes as follows:

CD/SACD

AX (COAXIAL) in

OPT (

OPTICAL) in

USB in

When an external input is selected, the unit can be used as a D/A

converter (page18).

Press and hold this button for more than 2seconds to enter the

setup mode (page20).

Remote control sensor

Receives signals from the remote control unit. Point the remote

control unit at this sensor when operating the remote control.

Disc tray

C D E J KF GB H IA

Display

OPEN/CLOSE

Press this button to open or close the disc tray.

STOP

Press this button to stop playback.

If you are playing a SACD that allows selectable layer playback,

when playback is stopped, press and hold this button for more

than 2seconds to change the play area of the SACD disc.

In setup mode, press this button to exit setup mode.

PLAY

Press this button to start playback.

The indicator ring lights during playback.

PAUSE

Press this button to pause playback.

The indicator ring blinks during pause mode.

Skip (.//)

Press these buttons to skip forward and backward.

During playback, press and hold these buttons for more than

1second to scan forward and backward.

Repeated pressing and holding of these buttons changes the

scanning speed (page15).

In setup mode, press these buttons to change adjustable settings

(page20).

English

Identifying the Parts (Front Panel Display)

Disc type indicators

Show the type of disc currently loaded; CD or SACD.

< The corresponding indicators also light when DVD video, DVD audio

or Video CD discs are loaded, although playback of these types of

discs is not possible with this unit. This unit can play back Super Audio

CD and CD only.

REPEAT indicator

Lights when repeat play mode is selected.

SETUP indicator

Lights in the setup mode.

Message area

Shows times, status messages, etc.

DOWN MIX indicator

Lights to show that a multi-channel audio source has been down

mixed to 2 channels.

Channel indicators

Lights “L” and “R” during playback of 2-channel stereo sound.

Lights the channels currently in use, during playback of multi-channel

sound.

Identifying the Parts (Remote Control Unit)

To simplify explanations, instructions in this manual might refer to the main unit or

remote control unit only. In such cases, the same controls on the remote control and main

unit will operate similarly.

English

DIMMER

Press this button to select one of four brightness levels for the

display and indicator lamps.

SETUP

This button will not work on the K-01/K-03, However, this can be

used for setup functions with Esoteric amplifiers.

OPEN/CLOSE (L)

Press this button to open and close the disc tray.

CLEAR

If you accidentally press the “+10” button, press this to cancel the

input value.

DISPLAY

During playback or pause mode, press this button to change the

display (page17).

REPEAT

In CD/SACD mode, press this button to change the repeat mode

(page17).

GROUP/TITLE ( )

The group/ title function cannot be used with this unit.

However, if this button is pressed when playback is stopped, the

source can be selected from CD/SACD and external input. When

external input is selected, the unit will be used as a D/A converter

(page18).

TRACK/CHAP/Skip (.//)

Press these buttons to skip forward and backward.

In setup mode, press these buttons to change a setting (page20).

PAUSE (J)

Press this button to pause playback.

MUTING

In the setup menu, when the attenuator function is set to “ON”,

pressing this button temporarily mutes the sound (page21).

This button may also be used for the mute function of Esoteric

amplifiers.

ON/LIGHT

When this button is pressed, the white buttons on the remote

control unit will light for a few seconds.

STANDBY

This button will not work with the K-01/K-03. Please ignore this

button.

Number buttons

Use these buttons to enter the track number for playback.

PLAY AREA

When a hybrid Super Audio CD is loaded and the disc is not

being played, press this button to change the play area of the

disc (page15).

2CH/MULTI

This button will not work with the K-01/K-03. Please ignore this

button.

AUDIO

Use this button to program tracks for playback (page16).

SCAN (m/,)

Press these buttons to scan forward and backward during

playback.

Repeatedly pressing these buttons changes the scanning speed.

STOP (H)

Press this button to stop playback.

PLAY (y)

Press this button to start playback.

VOLUME (+/

)

In the setup menu, when the attenuator function is set to “ON”,

these buttons control the output volume (page21).

These buttons can also be used to control the volume of

compatible Esoteric amplifiers.

INPUT

This button will not work with the K-01/K-03. However, it can be

used for switch the input source selection of compatible Esoteric

amplifiers.

1 3 54

Press the STANDBY/ON button to turn the unit on.

The indicator ring lights in blue.

< When an external input (COAX in, OPT in, USB in) is selected,

pressing the MODE button returns you to the SACD/CD mode.

Press the OPEN/CLOSE button to open the disc tray.

The tray opens toward you.

Set a disc with the printed label face up.

< Make sure the disc is clean, free from scratches, is not sticky, does

not have any “after market enhancements,” and is centered in the

tray. These precautions will help you to avoid any malfunction or

jamming of the tray or damage to the disc.

Press the OPEN/CLOSE button again to close the tray.

The tray will close.

Be careful not to let your fingers be pinched by the tray.

< Loading a disc takes a few seconds. Wait until the disc type

indicator, total number of tracks and total playing time of the

disc are displayed.

Playback

Press the PLAY button to start playback.

Playback starts from the first track on the disc.

During playback, the indicator ring of the PLAY button lights in

blue.

Suspending playback temporarily

(Pause mode)

Press the PAUSE button to pause playback.

The indicator ring of the PLAY button blinks.

Press the PLAY button or the PAUSE button to restart playback.

Stopping playback

During playback, press the STOP button to stop playback.

Opening and closing the disc tray

Press the OPEN/CLOSE button to open the tray.

Press the OPEN/CLOSE button again to close the tray.

< When the OPEN/CLOSE button is pressed during playback, it will

take a few seconds before the disc is unloaded and the tray opens.

English

Searching for a part of a track

During playback press the SCAN (m/,) buttons on the

remote control unit to scan backwards and forwards. Press the

PLAY (G) button to restart playback at normal speed at the desired

location.

< When using the front panel controls of the player, press and hold

the Skip (.//) buttons repeatedly.

Each time the SCAN (.//) buttons are briefly pressed, the

scanning speed changes as follows:

123 Normal playback

FastSlow

< The blinking speed of “<” or “>” on the display shows the current

scanning speed.

Skipping playback

Press the Skip (.//) buttons repeatedly until the desired

track is found.

The selected track will be played from the beginning.

< If the . button is pressed once during playback, the track being

played will be played again from the beginning. To return to the

beginning of the previous track, press the . button repeatedly.

However, If it is pressed within one second from the start of the

track, playback returns to the start of the previous track.

< If tracks are skipped when playback is paused or stopped, playback

is paused at the start of the selected track. Press the PLAY (G)

button to start playback of the selected track.

Selecting the playback area (SACD)

Other than regular Super Audio CDs that contain 2-channel stereo,

there are some types of Super Audio CDs that have multi-channel

stereo, such as hybrid discs (two-layer discs) that contain Super Audio

CD and regular CD (PCM), data.

If you have a disc with selectable playback layers, and if you want to

change the playback option, follow these directions.

Hold down

more than 2 sec.

Press the STOP button on the front panel for more than

2seconds to change the playback area of a Super Audio CD when

playback is stopped.

< As an example, this option allows you to select the CD/PCM layer,

or SACD (DSD), layer of a hybrid Super Audio CD.

< Pressing the PLAY AREA button on the remote control unit can also

change the playback area.

Direct playback

When stopped or during playback, press the Number buttons

to directly select a track.

Playback starts from the selected track.

Examples:

To playback track 5

To playback track 23

To playback track 30

< If you accidentally press the “+10” button, press the CLEAR button

to cancel the input value.

When the selection of track numbers is completed, press

the PLAY (G) button to start programed playback.

< When you program tracks during playback, programed playback

will start automatically and you don't have to press the PLAY (G)

button.

Clearing the last track from the list

Press the CLEAR button to clear the last track from the list.

Adding tracks to the list

Use the number buttons to add a track to the list.

Clearing the whole program

Press the AUDIO button to clear the program.

Pressing the OPEN/CLOSE button or the POWER button also clears

the program.

Up to 30 tracks can be programmed in the desired order.

Press the AUDIO button (during playback or in stop

mode).

< When you press the AUDIO button during playback, the current

track is added as the first program number to the program.

Select the track number that you want to add using the

number buttons.

Examples:

To playback track 5

o playback track 23

o playback track 30

< Press the CLEAR button to cancel the last input value.

Example:

Programmed track

number

Programme

number

Repeat step

to program more tracks.

Programmed Playback

English

During playback, press the REPEAT button to change the repeat

mode.

Each time the REPEAT button is pressed, the repeat setting changes

as follows:

REPEAT TRK (Track repeat)

The track being played will be played

repeatedly.

If you select another track, the selected

track will be played repeatedly.

All the tracks on the disc will be played

repeatedly.

REPEAT DSC (Disc repeat)

REPEAT OFF

< When the playback stops, the repeat mode is canceled.

Repeat playback Changing the Display Mode

Press the DISPLAY button to change the display.

Each time the DISPLAY button is pressed, the display changes as

follows:

During playback

Examples:

Elapsed time

of current track

Currently playing

track number

Remaining time of current track

Total elapsed time of disc

Total remaining time of disc

When playback is stopped

Example:

Total tracks Total playing time

D/A Converter Mode

This unit can be used as a multi-chip 32 bit, dual mono, D/A converter.

When playback is stopped, press the MODE button to change

the input source.

Each time the MODE button is pressed, the input source changes

as follows:

CD/SACD

AX (COAXIAL) in

OPT (

OPTICAL) in

USB in

< You can also change the input source by pressing the GROUP/

TITLE ( ) buttons on the remote control unit.

< When an external input (“COAX in”, “OPT in” or “USB in”) is selected,

the input source name and its sampling frequency are displayed.

When there is no input signal or the input signal cannot be

locked, the input name blinks and the sampling frequency is not

displayed.

< When the input digital signal is not audio data or the format of the

audio signal is not compatible with this unit, such as Dolby Digital,

dts, AAC, etc., the sampling frequency is displayed as “---”.

If this happens, set the digital OUT setting of the connected device

to PCM audio output.

< When an external input (“COAX in”, “OPT in” or “USB in”) is selected,

only the OPEN/CLOSE button can be used for CD/SACD operation.

Connecting with a Computer

You can connect this unit’s USB port with a computer using a USB

cable and play back music files stored on the computer using the

unit’s D/A converter. This unit can be connected by USB and used with

a computer running Windows XP, Windows Vista, Windows 7, Mac OS

X 10.6.4 or later. Use with a computer running a different operating

system cannot be guaranteed.

< Depending on the computer’s hardware and software

configuration, the unit might not function even when used with

one of the operating systems listed above.

Using HIGH SPEED 1 or HIGH SPEED 2 mode

When this unit is connected to a computer via USB, you can select

one of three modes. See pages 20 – 23 for details about setting

the mode.

To use HIGH SPEED 1 or HIGH SPEED 2 mode, you must install

dedicated driver software into your computer, before connecting

the unit.

If you connect the unit with the computer before installing the

driver, it will not function properly. Moreover, when using Windows

XP, the computer could become remarkably slower and require

restarting in some cases.

Website address for downloading the dedicated driver

software

http://www.esoteric.jp/products/esoteric/usb/usb_driver_e.html

Install the dedicated driver software after downloading the file

from the website above.

Connection modes

NORMAL mode

Set the unit to USB>NOR (page22).

Connect to the computer using USB FULL SPEED mode.

The sampling frequencies that can be transmitted are 32 kHz, 44.1

kHz, 48 kHz, 88.2 kHz and 96 kHz.

There is no need to install driver software to use this mode when

connecting the unit with a computer. The standard USB audio

driver included with the computer operating system can be used

for connection.

< The first time you connect this unit to a computer running

Windows OS, the computer will detect the unit’s USB port and

install the driver automatically. Follow the instructions given by the

operating system, and launch your audio file playback software

after completing the installation.

If the connection has been made properly, “ESOTERIC USB AUDIO”

will be selectable as an audio output destination.

HIGH SPEED 1 mode

Set the unit to USB>HS_1 (page22).

Connect to the computer using USB HIGH SPEED mode.

Sampling frequencies that can be transmitted are 32 kHz, 44.1 kHz,

48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz.

English

You must install the dedicated driver software before connecting

the unit to the computer (see left column).

Download this driver software from our website.

If the connection has been made properly, “ESOTERIC USB HS

AUDIO” will be selectable as an audio output destination.

HIGH SPEED 2 mode

Set the unit to USB>HS_2 (page22).

Connect to the computer using USB HIGH SPEED asynchronous

mode.

Sampling frequencies that can be transmitted are 32 kHz, 44.1 kHz,

48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz.

You must install the dedicated driver software before connecting

the unit to the computer (see left column).

Download this driver software from our website.

If the connection has been made properly, “ESOTERIC USB HS

ASYNC AUDIO” will be selectable as an audio output destination.

In asynchronous mode, jitter that occurs during transfer

is suppressed because the clock signal of this unit is used for

playback of the audio data transmitted from the computer.

< If skipping or periodic noise occurs during playback when the unit

is connected to a computer using HIGH SPEED 2 mode, set the unit

to HIGH SPEED 1 mode instead.

Connecting with a computer

< To use HIGH SPEED 1 or HIGH SPEED 2 mode, you must install

dedicated driver software before connecting the unit (page18).

Connect the unit to the computer using a USB cable.

< Use a cable with a connector that fits the USB port on the unit

and is rated at USB 2.0 speeds or above.

Turn the computer power ON.

Confirm that the operating system has started properly.

Press the POWER button to turn the unit power ON.

Press the MODE button repeatedly to select “USB in”.

Start playback of the music file on the computer.

Even better sound quality can be achieved by setting the

volume on the computer to maximum and using the amplifier

connected to this unit to adjust the volume. Set the volume of

the amplifier to the minimum at the beginning of playback and

gradually raise the level.

< The computer and this unit cannot be used to control each other.

< This unit cannot transmit music files to the computer by USB.

< When playing back a music file using the USB connection, do not

attempt any of the following operations. Doing so could cause

the computer to behave irregularly. Always stop music playback

software on your computer before doing any of the following:

Disconnecting the USB cable

Turning the unit’s power OFF

Changing the input source

< When playing back a music file using the USB connection,

computer operation sounds will also be played through this unit.

To avoid this, make appropriate settings on the computer.

< If you connect this unit with the computer or you set this unit’s

input to “USB” after starting music playback software, music files

might not play back properly. If this occurs, restart the music

playback software or reboot the computer.

Press and hold the MODE button for more than 2seconds

to enter the setup mode.

Press the MODE button repeatedly to select an item.

Each time the MODE button is pressed, the item changes as

follows:

DF>

UPC

ONV>

A_OUT>

XLR>

USB>

D_OUT>

ATT>

FLaOFF>

WORD>

< Depending on the selected input source or current operation,

some menu items are not available.

< If no button is pressed for more than 10seconds, setup mode

will be canceled and the unit returns to the previous display.

< In setup mode, if you press and hold the MODE button for more

than 2seconds or press the STOP button, setup mode will be

canceled and the unit returns to the previous display.

Press the Skip (.//) buttons to change the setting.

Repeat steps

and

as required.

Press the MODE button for more than 2seconds to exit the

setup mode.

< You can also exit the setup mode by pressing the STOP button.

< Memorized settings are stored even after the power cord has

been disconnected.

Changing Settings

Setting the upconversion rate

used by the upconverter

Display: UPCONV>***

< This can be set for each input separately.

< During SACD playback, the DSD signal is transmitted directly to the

D/A converter.

ORG (original)

The input signal is transmitted directly to the D/A converter

without conversion.

2Fs

32 kHz, 44.1 kHz and 48 kHz sources are upconverted to double

values of 64 kHz, 88.2 kHz and 96 kHz and then transmitted to the

D/A converter.

4Fs

32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz sources are

upconverted to double or quadruple values of 128 kHz, 176.4 kHz

or 192 kHz and then transmitted to the D/A converter.

DSD

The signal is converted to DSD digital format, and then transmitted

to the D/A converter.

Setting Items (1)

La page charge ...

Esoteric K-01 Le manuel du propriétaire

Marque: Esoteric

Modèle: K-01

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Ce manuel convient également à

K-03

Télécharger le PDF

rapport

dans d''autres langues

English: Esoteric K-01 Owner's manual
español: Esoteric K-01 El manual del propietario

Esoteric K-01 Le manuel du propriétaire

Ce manuel convient également à

Esoteric K-01 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents