Ariston ANDRIS RS 8U 1.4KW Manuel utilisateur

Marque: Ariston

Modèle: ANDRIS RS 8U 1.4KW

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Ce manuel convient également à

ANDRIS RS 2.5U 1.4KW

Mini-Tank Electric Water Heater

Calentadores eléctricos mini tanque

Mini-ballon électrique Chauffe-eau

This manual must only be used by a quali ed installer / service technician. Read all instructions in this

manual before installing. Perform steps in the given order. Failure to do so could result in substantial

property damage, severe personal injury, or death.

The manufacturer reserves the right to make product changes or updates without notice and will not be

held liable for typographical errors in literature.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead

by weight as required by the Safe Drinking Water Act, Section 1417, and are certi ed as such by IAPMO.

California Proposition 65 Warning: This product contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

$'9(57(1&,$

Este manual es para uso exclusivo de instaladores y técnicos de servicio cuali cados. Lea todas las instrucciones

proporcionadas en este manual antes de llevar a cabo la instalación. Realice los pasos en las secuencias indicadas.

De lo contrario, podrían producirse daños materiales signi cativos, lesiones graves o incluso la muerte.

AVIS2

El fabricante se reserva el derecho a realizar modi caciones o actualizaciones al producto sin necesidad

de previo aviso, y no puede considerarse responsable por errores tipográ cos en la documentación.

NOTA AL CONSUMIDOR: CONSERVE TODAS LAS INSTRUCCIONES PARA FUTURAS CONSULTAS.

Las super cies de estos productos que entran en contacto con agua potable contienen menos del

0,25% de plomo en peso, tal y como lo requiere la Ley de seguridad sobre el agua potable de los Estados

Unidos, sección 1417, y están certi cadas como tales por IAPMO.

Advertencia conforme a la Proposición 65 de California: Este producto contiene sustancias químicas que,

conforme al estado de California, producen cáncer, defectos de nacimiento u otros daños reproductivos.

AVERTISSEMENT

Ce manuel doit être utilisé uniquement par un installateur / technicien de maintenance quali é. Lire toutes les instructions

de ce manuel avant de procéder à l’installation. E ectuer les opérations dans l’ordre indiqué. Tout non-respect de cette

consigne peut entraîner des dégâts matériels considérables, des dommages corporels graves voire la mort.

AVIS

Le fabricant se réserve le droit d'apporter des modi cations ou des mises à jour sur le produit sans

préavis et pourra être tenu pour responsable des erreurs typographiques dans la documentation.

REMARQUE À L’ATTENTION DU CLIENT: VEUILLEZ CONSERVER TOUTES LES INSTRUCTIONS POUR Y FAIRE RÉFÉRENCE ULTÉRIEUREMENT.

Les surfaces de ces produits en contact avec de l'eau potable (consommable) contiennent moins de 0,25% de plomb

en poids, comme l'exige la Loi sur la salubrité de l'eau, Section 1417, et sont certi ées comme telles par l'IAPMO.

Avertissement Proposition 65 de la Californie: Ce produit contient des produits chimiques reconnus par l'État de

Californie pour provoquer des cancers et des malformations congénitales ou autres problèmes de reproduction.

The following de ned terms are used throughout this manual to bring attention to the presence of hazards of

various risk levels or to important product information.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury

or death.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in personal injury or

death.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor

personal injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not

avoided, may result in property damage.

NOTICE is used to address practices not related to personal injury.

Foreword

This manual is intended to be used in conjunction with other literature provided with the water heater. This

includes all related control information. It is important that this manual, all other documents included in this

system, and additional publications be reviewed in their entirety before beginning any work.

Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code

authorities, and utility companies which pertain to this type of water heating equipment.

Authority Having Jurisdiction (AHJ) – The AHJ may be a federal, state, local government, or individual such as a

 re chief,  re marshal, chief of a  re prevention bureau, labor department or health department, building o cial

or electrical inspector, or others having statutory authority. In some circumstances, the property owner or his/

her agent assumes the role, and at government installations, the commanding o cer or departmental o cial

may be the AHJ.

NOTE: The manufacturer reserves the right to modify product technical speci cations and components without

prior notice.

For the Installer

This water heater must be installed by quali ed and licensed personnel. The installer should be guided by the

instructions furnished with the water heater, and by local codes and utility company requirements.

Installations Must Comply With:

Local, state, provincial, and national codes, laws, regulations, and ordinances.

The latest version of the National Electrical Code, NFPA No. 70.

Table of Contents

Part 1 - General Safety Information 4

A. When Servicing the Water Heating System 5

B. Heater Water 5

C. Freeze Protection 5

D. Water Temperature Adjustment 6

Part 2 - Prepare the Water Heater 6

A. Model Overview 6

B. Locating the Water Heater 6

C. Water Chemistry Requirements 7

D. Technical Speci cations and Dimensions 9

Part 3 - Installation Instructions 9

A. Mounting the Water Heater 9

1. Wall Mounting 9

2. Floor Mounting 9

B. Plumbing 9

C. Thermal Expansion 10

D. Condensation 10

E. Temperature and Pressure Relief Valve 10

F. Scalding 11

G. Filling the Heater 12

Part 4 - Electrical Connection 12

Part 5 - Installation Checklist 13

Part 6 - Operation 13

A. Starting and Testing 13

B. Thermostat Adjustment 13

Part 7 - Maintenance 13

A. Removing the Cover 14

B. Draining the Heater 14

C. Removing the Heating Element 14

D. Inspecting the Anode Rod 14

E. Descaling the Heating Element 15

SPECIAL ATTENTION BOXES

Part 1 - General Safety Information

This water heater is approved for indoor installations only and is not intended for use as a pool heater. Heater

must have room for service: 24” front, 6” top, 1” left side, 3” right side, and 0” bottom are minimum recommended

service clearances. (A combustible door or removable panel is acceptable front clearance.) This water heater

has been approved for closet installation and installation on combustible  ooring. Do not install directly on

carpeting. Install the water heater in a location where temperature and pressure relief valve discharge or a leak

will not result in damage to the surrounding area. If such a location is not available, install an auxiliary catch pan.

NOTE: Obey all local codes. Obtain all applicable permits before installing the water heater.

NOTE: Install all system components and piping in such a manner that does not reduce the performance of any

 re rated assembly.

The manufacturer cannot be responsible for damages caused by improper installation or by failure to follow the

instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions to reduce the risk of  re, electric shock, or injury to

persons should be followed, including:

1. READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.

2. This water heater must be grounded. Connect only to a properly grounded outlet. See Part 4 – Heater Wiring,

this manual, for grounding details.

3. Install or locate this water heater only in accordance with the provided installation instructions.

4. Use this water heater only for its intended use as described in this manual.

5. Models 2.5 and 4 come equipped with a power cord. Do not use an extension cord set with this water heater.

If no receptacle is available adjacent to the water heater, contact a quali ed electrician to have one properly

installed. Model 8 must be hard-wired. See installation instructions for details.

6. As with any appliance, close supervision is necessary when used by children.

7. Do not operate this water heater if it has a damaged cord or plug, if it is not working properly, or if it has been

damaged or dropped.

8. This water heater should be serviced only by quali ed service personnel. Contact the water heater installer or

a quali ed service agency for examination, repair, or adjustment.

9. Failure to inspect the anode rod at least once a year could cause the tank to fail and leak. This condition is not

covered under the manufacturer’s warranty.

SAVE THESE INSTRUCTIONS

Installer - Read all instructions in this manual before installing. Perform steps in the given order.

User - This manual is for use only by a quali ed heating installer / service technician. Have this water heater

serviced / inspected annually by a quali ed service technician.

FAILURE TO ADHERE TO THE GUIDELINES ON THIS PAGE CAN RESULT IN SUBSTANTIAL PROPERTY

DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

NOTE: If the water heater is exposed to the following, do not operate. Immediately call a quali ed service

technician.

1. Fire

2. Damage

3. Water

Failure to follow this information could result in property damage, severe personal injury, or death.

Part 8 - Troubleshooting 15

A. Resetting the High Limit Switch 16

B. Checking Thermostat Operation 16

C. Changing the Heating Element 16

D. Changing the Thermostat 16

Part 9 - Replacement Parts 17

Mini Tank Electric Water Heater Limited Warranty 18

Customer Installation Record Form 20

High heat sources (sources generating heat 100

F / 37

C or greater, such as stove pipes, space heaters, etc.) may

damage plastic components of the water heater as well as plastic vent pipe materials. Such damages ARE NOT

covered by warranty. It is recommended to keep a minimum clearance of 8” from high heat sources. Observe

heat source manufacturer instructions, as well as local, state, provincial, and national codes, laws, regulations

and ordinances when installing this water heater and related components near high heat sources.

Hydrogen gas can be produced in a hot water system served by this heater that has not been used for a long

period of time (generally 2 weeks or more). Hydrogen gas is extremely  ammable. To reduce the risk of injury

under these conditions, it is recommended that the hot water faucet be opened for several minutes at the

kitchen sink before using any electrical appliance connected to the hot water system. If hydrogen gas is present,

there will probably be an unusual sound such as air escaping through the pipe as the water begins to  ow. There

should be no smoking or open  ame near the faucet at the time it is open. Failure to follow these instructions

will result in serious personal injury or death.

A. When Servicing the Water Heating System

To avoid electric shock, disconnect electrical supply before performing maintenance.

NOTE: When inquiring about service or troubleshooting, reference the model and serial numbers from the water

heater rating label.

To avoid severe burns, allow water heater and associated equipment to cool before servicing.

B. Heater Water

Do not use petroleum-based cleaning or sealing compounds in a water heating system. Gaskets and seals in the

system may be damaged. This can result in substantial property damage.

Do not use “homemade cures” or “patent medicines”. Damage to the water heater, substantial property damage,

and/or serious personal injury may result.

C. Freeze Protection

NOTE: Consider piping and installation when determining heater location.

Failure of the water heater due to freeze related damage IS NOT covered by product warranty.

NEVER use any toxic chemical, including automotive, standard glycol antifreeze, or ethylene glycol made for

hydronic (non-potable) systems. These chemicals can attack gaskets and seals in water systems, are poisonous

if consumed, and can cause personal injury or death.

UNCRATING THE WATER HEATER - Any claims for damage or shortage in shipment must be  led immediately

against the transportation company by the consignee.

Be sure to disconnect electrical power before performing service. Failure to do so could result in electrical shock,

property damage, serious personal injury, or death.

Tank failure due to neglecting the anode rod is not covered under warranty. See Maintenance, this manual.

DO NOT USE THIS WATER HEATER IF ANY PART HAS BEEN SUBMERGED IN WATER. Immediately call

a quali ed service technician. The water heater MUST BE replaced if it has been submerged. Attempting to

operate a water heater that has been submerged could create numerous harmful conditions, such as a potential

gas leakage causing a  re and/or explosion, or the release of mold, bacteria, or other harmful particulates into

the air. Operating a previously submerged water heater could result in property damage, severe personal injury,

or death.

NOTE: Water heater damage due to  ood or submersion is considered an Act of God, and IS NOT covered under

product warranty.

Do not use this water heater for anything other than its intended purpose (as described in this manual). Doing

so could result in property damage and WILL VOID product warranty.

D. Water Temperature Adjustment

The water heater thermostat has been pre-set at

the factory at a temperature equal to or below

125

F (51.7

C) according to UL certi cation. See

Figure 1. If the water heater is going to have a

set temperature above 120

F, it is recommended

to use an ASSE 1017 rated mixing valve to avoid

severe burns or death from scalding temperatures.

Figure 1 - Thermostat

Households with small children, disabled, or elderly persons

may require a 120

F or lower temperature setting to prevent

severe personal injury or death due to scalding.

Approximate Time / Temperature Relationships in

Scalds

120

F More than 5 minutes

125

F 1 1/2 to 2 minutes

130

F About 30 seconds

135

F About 10 seconds

140

F Less than 5 seconds

145

F Less than 3 seconds

150

F About 1 1/2 seconds

155

F About 1 second

Table 1 - Approx. Time / Temperature Relationships in Scalds

A. Model Overview

The following  gures detail speci c water heater model components. Some components may ship factory

installed. This depends on water heater model.

Part 2 - Prepare the Water Heater

Remove all sides of the shipping crate to allow the heater to be moved into its installation location.

COLD WEATHER HANDLING - If the water heater has been stored in a very cold location (BELOW 0

F) before

installation, handle with care until the components come to room temperature. Failure to do so could result in

damage to the water heater.

B. Locating the Water Heater

NOTE: After adjusting the water temperature at the thermostat, allow the water heater enough time to heat

the water to temperature. After the water heater has stopped heating, use a thermometer to measure the water

temperature at a hot water outlet in the structure.

This water heater is certi ed for indoor use only. DO NOT INSTALL OUTDOORS. Outdoor installations ARE NOT

covered by warranty. Failure to install the water heater indoors could result in property damage, severe personal

injury, or death.

All water heaters eventually leak. Locate the water heater where any leakage from the relief valve, related piping,

tank, or connections will not result in damage to surrounding areas or lower  oors of the building. Any water

heater should be installed in such a manner that if it should leak the resulting  ow of water will not cause

damage to the area in which it is installed. National Plumbing codes require a drain pan for any water heater

installation. Failure to install one is the sole responsibility of owner and/or installer. Reference UPC 2000 (Uniform

Plumbing Code) Section 510 - Protection from Damage or IPC 200 (International Plumbing code) Section 504 -

Safety Devices. Leakage damages ARE NOT covered by warranty.

In addition, water leak detection devices and automatic water shuto valves are readily available at plumbing

supply houses. IT IS HIGHLY RECOMMENDED BY THE MANUFACTURER TO INSTALL WATER LEAK DETECTION

DEVICES AND AUTOMATIC SHUTOFF VALVES IN ANY WATER HEATER INSTALLATION WHERE A LEAKAGE OF

WATER COULD RESULT IN PROPERTY DAMAGES.

1. Installation Area (Mechanical Room) Operating Conditions

• Ensure ambient temperatures are higher than 32

F / 0

C and lower than 104

F / 40

• Avoid continuously high levels of humidity

• Never close existing ventilation openings

NOTE: When installing in a zero clearance location, it may not be possible to read or view some product labeling.

It is recommended to make note of the water heater model and serial number.

2. Choose a location for the water heater as centralized to the piping and electrical system as possible. Also, locate

the water heater and domestic water piping where it will not be exposed to freezing temperatures. All piping

should be insulated. Additionally, place the water heater so that the drain, controls, and inlets/outlets are easily

accessible.

NOTE: To save on heating costs and improve energy e ciency keep the distance between the water heater and

 xtures to a minimum to reduce heat loss from excess piping and keep friction loss at a minimum. Ensure all

water heater piping is properly insulated to minimize heat loss.

NOTE: If you do not provide the minimum recommended service clearances it might not be possible to service

the water heater without removing it from the space.

NOTE: In the State of California, the water heater must be braced, anchored, or strapped to avoid moving during

an earthquake. Contact local utilities for code requirements in your area. Visit http://www.dsa.dgs.ca.gov or call

1-916-445-8100 and request instructions.

3. Check area around water heater. Remove any combustible materials, gasoline, and other  ammable liquids.

This water heater must not be located near  ammable liquids such as gasoline, butane, lique ed propane,

adhesives, solvents, paint thinners, etc., as the controls of this water heater could ignite these vapors and cause

an explosion resulting in property damage, severe personal injury, or death.

This water heater must be installed upright in the vertical position as described in this manual. DO NOT attempt

to install this water heater in any other orientation. Doing so will result in improper water heater operation and

property damage, and could result in serious personal injury or death.

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk. Ensure

that the installation location adheres to the information included in this manual. Failure to do so could result in

property damage, serious personal injury, or death.

4. If the water heater is to replace an existing water heater, check for and correct any existing system problems

such as:

• System leaks

• Location that could cause the system and water heater to freeze and leak

• Incorrectly-sized expansion tank

5. This water heater must be installed vertical on a level surface.

C. Water Chemistry Requirements

Chemical imbalance of the water supply may a ect e ciency and cause severe damage to the appliance and

associated equipment. Water quality must be professionally analyzed to determine whether it is necessary

to treat the water. Various solutions are available to adjust water quality. Adverse water quality will a ect the

reliability of the system. In addition, operating temperatures above 135

F will accelerate the build-up of lime

scale and possibly shorten appliance service life. Failure of an appliance due to lime scale build-up, low pH, or

other chemical imbalance IS NOT covered by the warranty.

NOTE: A combustible door or removable panel is acceptable front clearance.

The service life of the water heater’s exposed metallic surfaces, such as the junction box, is directly in uenced

by proximity to damp and salty marine environments. In such areas higher concentration levels of chlorides

from sea spray coupled with relative humidity can lead to degradation of water heater components and cause

premature water heater failure. Such failures ARE NOT covered by warranty.

Failure of the water heater or components due to incorrect operating conditions IS NOT covered by product

warranty.

The water must be potable, free of corrosive chemicals, sand, dirt, and other contaminates. It is up to the installer

to ensure the water does not contain corrosive chemicals or elements that can damage the heat exchanger.

Potable water is de ned as drinkable water supplied from utility or well water in compliance with EPA secondary

maximum contaminant levels (40 CFR Part 143.3). If the water contains contaminants higher than outlined by the

EPA, water treatment is recommended and additional, more frequent maintenance may be required.

If you suspect that your water is contaminated in any way, discontinue use of the appliance and contact an

authorized technician or licensed professional.

Failure of electric elements due to lime scale build-up on the heating surface, low pH, or other imbalance IS NOT

covered by the warranty.

Water pH between 6.5 and 8.5

• pH levels below 6.5 can cause an increase in the rate of corrosion. pH of 8.5 or higher can potentially cause

lime scale build-up

• Maintain water pH between 6.5 and 8.5. Check with litmus paper or have it chemically analyzed by a local

water treatment company.

• If the pH is not between 6.5 and 8.5, consult a local water treatment company for solutions.

Hardness between 4 grains (70 mg/L) and 20 grains (350mg/L):

• The appliance must not be supplied with water of hardness less than 4 grains (70 mg/L), nor with especially

hard water (greater than 20 grains (350mg/L)); we recommend installing a water softener, properly calibrated

and controlled - do not allow the residual hardness to fall below 9 grains (150mg/L).

Chloride concentration less than 100 ppm (mg/L)

• Do not  ll appliance or operate with water containing chlorides in excess of 100 ppm (mg/L).

• Using chlorinated fresh water should be acceptable as levels are typically less than 5 ppm (mg/L).

• Do not connect the appliance to directly heat swimming pool or spa water.

Total Dissolved Solids (TDS) less than 500 ppm (mg/L)

• Total dissolved solids are minerals, salts, metals, and charged particles that are dissolved in water.

• The greater the amounts of TDS present, the higher the corrosion potential due to increased conductivity

in the water.

• If using softened water to  ll the appliance, it is still possible to have high TDS. This water can be corrosive.

Consult local water treatment companies for other treatment solutions to reduce this a ect.

Water conductivity not higher than 1200 μS / cm

*NOTE: To promote appliance service life, it is strongly recommended to follow the maintenance procedures in

this manual.

Figure 2 - Installation Detail

VALVE

CHECK VALVE

EXPANSION TANK

HOT WATER OUTLET

CATCH PAN

UNION

COLD WATER INLET

TEMP/PRESSURE

SHUT-OFF VALVE

DRAIN

RELIEF VALVE

MIXING VALVE

DRAIN

BALL VALVE

AUTOMATIC WATER

WATER LEAK

DETECTION

SENSOR

LP-665-D

07/31/18

NOTES:

1. Minimum pipe size should

match connection size. Upsize

pipe accordingly if greater  ow

is required.

2. A thermal expansion tank

suitable for potable water must

be sized and installed within

this piping system between

the back ow preventer and the

cold water inlet.

3. All circulators should have an

integral  ow check.

4. Drains and check valve

between unit and storage tank

will assist in purging air from

system.

5. These drawings are meant

to demonstrate system piping

only. The installer is responsible

for all equipment and detailing

required by local codes. In

Massachusetts, you must install

a vacuum relief valve per 248

CMR.

6. Mixing valve application is

optional, but recommended to

help prevent scalding. See Part

3 for more information.

7. It is highly recommended by the manufacturer to install water leak detection devices and automatic shuto valves in

any water heater installation where a leakage of water could result in property damages.

Table 2 - Technical Speci cations - *Nipple Adaptors Included in the Box

D. Technical Speci cations and Dimensions

Technical Data Units 2.5 4 8

Tank Capacity Gallons 2.7 4.0 8.0

Dimensions Inches

1/4

”W x

1/4

”H x 10

3/4

”D

1/4

”W x

1/4

”H x 12

3/4

”D

1/2

”W x

1/2

”H x 15

1/4

”D

Weight (Empty) lbs 15.5 17.6 29.5

Maximum Water Pressure psi 150

Recovery Rate (90

F Rise) gal/h 6.8 6.8

Temperature Range

Fahrenheit 65 - 161 65 - 161

Water Connections NPT 1/2” NPT

3/4” NPT Nipple

Adapters Included*

Relief Valve Installed Installed

Included, not

Installed

Nominal Voltage (1 Phase) VAC 110 / 120 (all Models)

Nominal Current Amps 12.0

Power at 120 VAC Watts 1440

Electrical Connection Plug In Hard Wired

Figure 3 - Dimensional Drawing

Part 3 - Installation Instructions

A. Mounting the Water Heater

These water heaters are designed to be installed under the sink.

1. Wall Mounting

• Fasten the supplied mounting bracket to the wall.

• Hang the water heater on the bracket.

• Tug down on the water heater to ensure that both “ ngers” of the bracket are seated in the mounting slots.

2. Floor Mounting

The water heater can be installed on the  oor. Install the included adhesive rubber  oor mounting feet onto the

bottom of the water heater. See the rubber feet installation instructions included in the pack.

B. Plumbing

It is mandatory that all plumbing be done in accordance with federal, local, and state plumbing codes and

practices. Failure to properly install the water heater WILL VOID the warranty. It is also necessary to use both

thread tape and pipe dope on all mechanical plumbing connections.

Install unions on the hot and cold water connections to easily disconnect the water heater for servicing.

Use screws suitable for the wall material and the weight of the water heater. Failure to do so could result in

property damages and damage to the water heater. Such damages ARE NOT covered by product warranty.

Failure of electric elements due to lime scale build-up on the heating surface, low pH, or other imbalance IS NOT

covered by the warranty.

C. Thermal Expansion

A check valve may be installed in the cold water inlet line as a separate back ow preventer, or may be part of

a pressure reducing valve, water meter, or water softener. An “open water system” refers to a system without a

check valve. A “closed water system” refers to a system with a check valve installed in the cold water inlet line.

As water is heated, it expands in volume and increases pressure within the water system. This action is referred

to as “thermal expansion”. In an open water system, expanding water which exceeds the capacity of the system

 ows back into the city main where pressure is easily dissipated.

A closed water system prevents expanding water from  owing back to the city main. The resulting thermal

expansion can rapidly increase pressure in the water heater and system piping. This rapid pressure increase

can exceed the setting of the pressure relief valve, causing it to operate during each heating cycle, resulting

in discharge from the T&P. This rapid and repeated expansion and contraction of components in the system

can cause premature failure of system components, including the relief valve and possibly the water heater.

Replacing the relief valve will not correct thermal expansion.

There are two recommendations to prevent this from happening:

1. Install a potable diaphragm-type hot water expansion tank to o set thermal expansion. Expansion tanks

are designed with an air cushion built in that compresses as system pressure increases, thereby relieving the

overpressure condition and eliminating repeated operation of the relief valve. This expansion tank should be

installed in the cold water line between the water heater and check valve, and must be sized for the entire water

volume of the hot water system. The expansion tank must have a minimum capacity of 1.5 gallons for every 50

gallons of stored water.

2. Install a 125 PSI pressure relief valve in the cold water supply line. Make sure the discharge of this valve is

directed to an open drain and protected from freezing. Contact the local water supplier or plumbing inspector

for information on how to control this situation. Do not plug the temperature and pressure relief valve.

Other methods of controlling thermal expansion are available. Check with the local water utility to determine

if a check valve exists in the cold water inlet line. Contact your installing contractor, water supplier, or

plumbing inspector for additional information regarding thermal expansion.

D. Condensation

Condensation can form on the water heater when it is  rst  lled with water, and may also occur with a heavy

water draw and very cold inlet water temperature. This condition is not unusual and will disappear as the water

becomes heated. However, if the condensation should continue, examine the piping and  ttings for possible

leaks.

NOTE: Insulating both the cold water inlet and hot water outlet pipes will reduce the opportunity for condensation

on the water heater piping.

E. Temperature and Pressure Relief Valve

For protection against excessive pressures and temperatures in this water heater, install the supplied temperature

and pressure relief valve certi ed by a nationally recognized testing laboratory that maintains periodic inspection

of production listed equipment or materials, as meeting the requirements for Relief Valves and Automatic Gas

Shuto Devices for Hot Water Supply Systems, ANSI Z21.22B / CSA 4.4-M99. The supplied temperature and pressure

relief valve is marked with a maximum set pressure (150 psi) that does not exceed the marked maximum working

pressure of the water heater (150 psi). Install the T&P valve in the opening provided and marked for this purpose

on the water heater, and orient it or provide tubing so that any discharge from the valve will exit at least 6” above

the structural  oor. The relief line cannot be in contact with any live electrical parts. The discharge opening must

not be blocked or reduced in size under any circumstances.

National Plumbing codes require a drain pan for any water heater installation. Failure to install one is the sole

responsibility of owner and/or installer. Reference UPC 2000 (Uniform Plumbing Code) Section 510 - Protection

from Damage or IPC 200 (International Plumbing code) Section 504 - Safety Devices.

• Connect the cold water inlet pipe to the inlet tapping (marked with a blue ring).

• Ensure an isolation valve is installed on the cold water supply to the water heater.

• Connect the hot water outlet pipe to the outlet tapping (marked with a red ring).

Do not apply heat to the Hot or Cold water heater connections. If sweat connections are used, sweat tubing to

the adapter before  tting adapter to the water connections on the heater. Any heat applied to the water heater

connections will permanently damage the dip tube and/or heat traps. Damages due to improper installation

practices ARE NOT covered by warranty.

RE-INSPECTION OF T&P RELIEF VALVES: T&P valves must be inspected AT LEAST ONCE EVERY THREE

YEARS, and replaced if necessary, by a licensed plumbing contractor or quali ed service technician to ensure

that the product has not been a ected by corrosive water conditions and to ensure that the valve and discharge

line have not been altered or tampered with illegally. Certain naturally occuring conditions may corrode the

valve and its components over time, rendering the valve inoperative. Such conditions can only be detected if

the valve and its components are physically removed and inspected. Do not attempt to conduct an inspection

on your own. Contact your plumbing contractor for a re-inspection to assure continued safety.

FAILURE TO RE-INSPECT THE T&P VALVE AS DIRECTED COULD RESULT IN UNSAFE TEMPERATURE AND/

OR PRESSURE BUILD-UP WHICH CAN RESULT IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR

DEATH.

F. Scalding

This water heater can deliver scalding water. Be careful whenever

using hot water to avoid scalding injury. Certain appliances such as

dishwashers and automatic clothes washers may require increased

water temperatures. By setting the thermostat on this heater to obtain

the increased water temperature required by these appliances you

may create the potential for scald injury.

To protect against injury, install a mixing valve in the water system. This

valve will reduce point of use discharge temperatures by mixing cold

and hot water in branch supply lines. Such valves are available from

your local plumbing supplier.

Table 3 details the relationship of water temperature and time with

regard to scald injury and may be used as a guide in determining the

safest water temperature for your applications.

To avoid water damage or scalding due to relief valve operation:

• Discharge line must be connected to relief valve outlet and run to a safe place of disposal. Terminate the

discharge line in a manner that will prevent possibility of severe burns or property damage should the relief

valve discharge.

• Discharge line must be as short as possible and the same size as the valve discharge connection throughout

its entire length.

• Discharge line must pitch downward from the valve and terminate at least 6” above the  oor drain, making

discharge clearly visible.

• The discharge line shall terminate plain, not threaded, with a material serviceable for temperatures of 375

or greater.

• Do not pipe discharge to any location where freezing could occur.

• No valve may be installed between the relief valve and heater or in the discharge line. Do not plug or place

any obstruction in the discharge line.

• Test the operation of the relief valve after  lling and pressurizing the system by lifting the lever. Make sure

the valve discharges freely. If the valve fails to operate correctly, immediately replace with a new properly

rated relief valve.

• Test T&P valve at least once annually to ensure the waterway is clear. If valve does not operate, turn the

heater “o ” and call a plumber immediately.

• Take care whenever operating relief valve to avoid scalding injury or property damage.

FAILURE TO COMPLY WITH THE ABOVE GUIDELINES COULD RESULT IN FAILURE OF RELIEF VALVE OPERATION,

RESULTING IN POSSIBILITY OF SUBSTANTIAL PROPERTY DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

Do not thread a cap or plug into the relief valve or relief valve line under any circumstances! Explosion and

property damage, serious injury, or death may result.

An ASSE 1017 or ASSE 1070 temperature limiting or mixing valve is recommended in installations servicing

disabled or elderly persons, or children. Mixing valves do not eliminate the risk of scalding.

To avoid scalding:

• Set the water heater set point temperature as low as possible.

• Feel water before bathing or showering.

• If thermostatic valves are required, use devices speci cally designed for such purpose. Install these devices

in accordance with instructions provided by the manufacturer.

Failure to install a temperature limiting or mixing valve and follow these instructions could result in property

damage, severe personal injury, or death due to scalds.

G. Filling the Heater

• Make certain any drain valves in the system are completely closed.

• Open the shut-o valve in the cold water supply line.

• Open the hot water faucets to allow air to vent from the heater and piping.

• Allow su cient time for the heater to completely  ll with water.

• Check for leaks.

When  lling the water heater, open a hot water tap to release air in the tank and piping. The tank must be full of

water before the heater is turned on. Failure to ensure the water heater is full before turning it on could result

in damage to the water heater and other property damages. Such damages ARE NOT covered by water heater

warranty.

Part 4 - Electrical Connection

Tank must be full of water before the power is turned on. The heating element will be damaged if energized for

even a short time while tank is dry. Failures due to “dry- ring” ARE NOT covered by warranty.

The voltage requirement and dedicated wattage load for the heater is speci ed on the water heater rating label.

Consult your local power company to determine if your electrical service is adequate for the additional load of

the heater.

The 8 Model must be hard wired. The 8 Model needs to be wired with 12 GA wire to a 20 amp branch circuit. All

wiring must conform to local code and the National Electric Code, and should be done by a quali ed licensed

electrician or the local electric utility. See Figure 4, A and B.

• Unscrew the junction box cover and remove it.

• Insert 12 AWG wire through the conduit into the junction box and secure with conduit strain relief (not

supplied).

• Connect the wires and screw on the cover of the junction box.

• Make appropriate wiring connections to the water heater per the National Electric Code.

• The unit must be grounded with supplied grounding cable inside the junction box.

• Secure the junction box cover once wiring connections have been made.

When the 8 Model is not within sight of the electrical circuit breakers, a circuit breaker lockout or additional local

means of disconnection for all non-grounded conductors must be provided that is within sight of the appliance

(Ref. NEC 422.31).

Be sure to ground the water heater. Failure to do so could result in property damage, severe personal injury, or

death.

Figure 4 - 8 Model Wiring

Part 5 - Installation Checklist

Water Heater Location Yes No

Close to area of heated water demand

Indoors and protected from freezing temperatures

Area free of  ammable vapors

Provisions made to protect area from water damage

Su cient room to service heater

Relief Valve Ye s N o

Temperature and Pressure Relief Valve properly installed and discharge line run to open drain

Discharge line protected from freezing

Wiring Ye s N o

Power supply voltage agrees with water heater rating plate

Branch circuit wire and fusing or circuit breaker of proper size

Electrical connections tight and unit properly grounded

Water Supply Ye s N o

Water heater completely  lled with water BEFORE operating the unit

Air purged from water heater and piping

Water connections tight and free of leaks

Table 3 - Installation Checklist

Part 6 - Operation

Tank must be full of water before the power is turned on. The heating element will be damaged if energized for

even a short time while tank is dry. Failures due to “dry- ring” ARE NOT covered by warranty.

A. Starting and Testing

For models not  tted with a switch:

• Supply power to the water heater by plugging in the power cord (2.5 and 4 Models) or turning on the circuit

breaker (8 Model).

• If the light does not turn on, turn the control knob in a clockwise direction.

• The light will turn on until the water temperature has reached the thermostat temperature setting. The light

will come back on any time the water temperature inside the tank drops below the thermostat setting.

B. Thermostat Adjustment

The temperature of the hot water is adjusted by rotating the knob (M, see Figure 5) located on the front cover.

• Turn the knob clockwise to increase temperature.

• Turn the knob counterclockwise to decrease temperature.

Do not attempt to repair this water heater yourself. Call a quali ed service technician for assistance. Always

turn o the power supply to the heater prior to servicing or draining the heater. Failure to do so could result in

property damage, severe personal injury, or death.

Part 7 - Maintenance

For most of these maintenance operations, the water will have to be drained from the heater. For all of these

operations, the power cord should be disconnected (2.5 or 4 Models) or the power turned o at the circuit

breaker (8 Model), and the front cover removed.

A. Removing the Cover

• Pry o the round knob cover plate (Figure

5, M) with a small  at head screwdriver.

• Pry o the screw covers (Figure 5, V) with

a small  at head screwdriver.

• Remove the Phillips screws.

• The cover (Figure 5, C) can now be

removed by pulling out its left hand edge.

When reassembling, work in the opposite

way, being careful to insert the tongue of

the cover into the slot.

B. Draining the Heater

If the heater has been installed with  exible

hoses:

• Shut o the power supply.

• Turn the heater upside down over a sink

to drain the water out of it.

The water heater can also be emptied by:

Figure 5 - Water Heater Cover and Thermostat Detail

D. Inspecting the Anode Rod

The purpose of the anode rod (Figure 7, N)

is to protect the tank against corrosion. The

anode rod must be inspected once a year to

determine whether it requires replacement.

To access the anode rod, the heating element

must be removed. See Removing the Heating

Element above. Upon inspection, the anode

rod surface should appear smooth. If the rod

surface appears pitted, bumpy, rusty, or if the

rod is missing completely, then it must be

replaced.

Original anode rod sizes:

• 2.5 and 4 Models: length 6 1/2”, diameter

5/8”

C. Removing the Heating Element

• Shut o the power supply and drain the

water heater.

• Remove the front cover plate. Disconnect

terminals X, Y, and T. See Figure 6.

• Unscrew the four (4) heating element

retaining nuts (Figure 6, F).

• Remove the element (Figure 6, G).

Figure 6 - Open Heater Cover Detail

• Siphoning through the inlet side hose.

• Keep a hot water faucet open while

siphoning.

If the heater has been installed with rigid

piping:

• Siphon the water out through any lower

service valve on the inlet side.

• Keep a hot water faucet open while

siphoning the water out.

Figure 7 - Heating Element and Anode Rod Detail

• 8 Model: length 8 1/4”, diameter 5/8”

Certain installations may require more frequent replacement of the anode rod:

• Recirculation applications;

• Poor water quality;

• Galvanic / Electrolytic corrosion;

• High  ow applications

Rusty water is usually an indication that the anode rod requires replacement. If rusty water is present, examine the

anode rod immediately and replace as needed. In the event of poor water quality, consult a local water treatment

professional for water treatment options. Always ensure the water heater is grounded. Damage resulting from

poor water quality or failure to replace the anode rod is not covered under the manufacturer’s warranty. For

additional questions, please contact Technical Support.

To change the anode rod:

1. Turn of the power supply and drain the heater (see Draining the Heater).

2. Remove the heating element (see previous section).

3. Unscrew the anode rod from threaded connection.

4. Remove and replace the anode rod (Figure 7, N).

5. Reinstall the heating element.

6. Re ll tank with water and purge air before restoring power.

E. Descaling the Heating Element

Scale deposits can a ect the heating capability of the element. Heavy scale can even cause damage to the

element. The element can be descaled either chemically or manually.

• Soak the element in white vinegar or other food grade descaling solution approved for use in potable water

systems.

• Once descaled, rinse well with a fresh water / baking soda solution.

The element can also be descaled manually:

• After the element has dried, use a soft brush (non-metallic to prevent damaging th stainless steel sheath)

on the element.

• Brush the dried minerals o .

Replace the anode rod if it is noticeably deteriorated or considerably smaller than described in Inspecting the

Anode Rod.

Reinstall the element after descaling. Ensure the element gasket is installed and that the element is rewired

correctly.

Ensure the tank has been re lled with water before restoring power to the water heater. Failures due to “dry-

 ring” ARE NOT covered by warranty.

Table 4 - Troubleshooting

Part 8 - Troubleshooting

Problem Solution

Water

Does Not

Get Hot

Ensure the power supply is on and working

If light does not come on, check that the high limit reset button is pushed in. Follow steps to reset

the switch, this manual.

If the indicator light works properly but temperature does not get hot at the tap, test for a plumbing

crossover. Shut o the cold supply to the heater and open the hot water tap. There should be no

water  owing. Any continued  ow indicates a crossover which will a ect the temperature and

need to be corrected.

Call a quali ed service technician to test the resistance of the heating element (8-10 ohms). Heating

element should be replaced if readings are outside these values.

Light Not

If the light does not come on, but the water gets hot, check for faulty bulb.

Check that the high limit reset button is pushed in. Follow steps, this manual.

Brown

Water

Brown or rusty water indicates a “spent” anode rod and possible deterioration of the tank body.

Check anode rod. See instructions, this manual. Inspect the tank for leaks.

Water

Odor

Smelly water could be due to an unusual reaction between local water and the heater’s anode rod.

Check anode rod. See instructions, this manual. Failure to do so may result in damage to the tank

and leaks.

Leaks

Check water  ttings and T&P  tting on top of tank. Remove front cover and inspect heating

element gasket.

If tank is leaking, review warranty to see if heater is still within warranty period.

Figure 8 - High Limit Switch Reset Detail

If draining of the water heater is necessary, open the T&P valve or a hot water tap to prevent vacuum buildup

in the tank and piping.

The risk of scald injury increases as you increase water temperature. A lower setting is more economical and

reduces the risk of scalding. Use a water tempering or mixing valve and extreme caution when using hot water

to avoid scald injury. Consult codes for conformance. Failure to follow the instructions in this warning statement

could result in serious personal injury or death from scalds.

Be sure to disconnect electrical power before performing service. Failure to do so could result in electrical shock,

property damage, serious personal injury, or death.

A. Resetting the High Limit Switch

Occasionally, the high temperature limit shut o device may trip

the reset. This occurs when water temperature exceeds 190

F. The

shut-o device may also trigger due to a power outage or electrical

storm.

To reach the thermostat:

• Disconnect the power cord (or shut o the circuit breaker - 8

Model) and remove the front cover.

• Firmly press the reset button with the tip of a ball point pen or

similar object. See Figure 8, B.

A click indicates the reset was tripped.

• Reconnect the power.

• Check the operation of the thermostat. See the following section.

Call a technician if the high limit needs to be reset frequently.

B. Checking Thermostat Operation

To check thermostat operation:

• Turn the temperature dial from high to low. If the red light does not turn o on the low setting, turn o the

power supply and call a quali ed service technician to replace the thermostat.

• If the red light does go o , the thermostat is working properly.

• Turn the dial to the desired setting. NOTE: A lower setting is more economical and reduces the risk of

scalding.

• Replace the cover plate.

NOTE: After adjusting the water temperature at the thermostat, allow the water heater enough time to heat

the water to temperature. After the water heater has stopped heating, use a thermometer to measure the water

temperature at a hot water outlet in the structure.

C. Changing the Heating Element

• Turn o the power supply and drain the water heater (see procedure, this manual).

• Remove heating element (see procedure, this manual).

• Install new element with gasket, making sure the gasket and element are positioned correctly. Tighten the

retaining nuts and wire connections.

• Ensure the thermostat temperature sensor is inserted into the well located on the element assembly and

secured with a black rubber grommet.

• Re ll the tank with water before restoring power.

D. Changing the Thermostat

• Turn o the power supply.

• Disconnect the two (2) wire connectors on the thermostat.

• Loosen the two (2) brass screws on the right side of the thermostat and pull the wires out.

• Unscrew and remove the two (2) Phillips screws holding the thermostat onto the tank.

• Install the new thermostat and re-attach the wiring and screws.

• Ensure the thermostat temperature sensor is inserted into the well located on the element assembly and

secured with black rubber grommet.

Part 9 - Replacement Parts

Figure 9 - Replacement Parts

Table 5 - Replacement Part Numbers

Item # Description

Part #

Item # Description

Part #

Model Model

2.5 4 8 2.5 4 8

Screw M6x12

( ange  xing)

65114656 65114656 65114656 10

Wall Hanging

Bracket

570341 570341 570341

Screw M6x12

(element  xing)

993000 993000 993000 11 Screw cover 65118185 65118185 65118185

3 Flange 65115359 65115359 65115359 12 Knob 65118186 65118186 65118186

Faston

protection

65118180 65118180 65118180 13 Plastic cover 65118187 65118187 65118188

5 Heating element 65118181 65118182 65118182 14

Plastic

protection

65118189 65118189 65118190

Heating

element gasket

65116115 65116115 65116115 15

Thermostat

lever

570029 570029 570029

Magnesium

anode

65103768-01 65103768-01 65103768-01 16 Cable clip 65150321 65150321 65150321

8 Power cable 65118183 65118183 65118184 17

TBSB Wired

Thermostat

65118191 65118192 65118192

9 T&P Valve 3/4" 65150323 65150323 65150323 18

Support for TBSB

Thermostat

65115134 65115134 -----

Mini Tank Electric Water Heater Limited Warranty

The manufacturer warrants each small capacity point of use

electric water heater and its components to be free from defects

in materials and workmanship according to the following terms,

conditions, and time periods. UNLESS OTHERWISE NOTED THESE

WARRANTIES COMMENCE ON THE DATE OF INSTALLATION. This

limited warranty is only available to the original consumer

purchaser (hereinafter “Owner”) of the water heater, and is non-

transferable.

WARRANTY PERIODS

Mini Tank Electric

Water Heater

Parts Tank

Two (2) Years Six (6) Years

COVERAGE

A. During the  rst two (2) years after the original date of

installation the manufacturer warrants that it will repair

or replace, at its option, any defective or malfunctioning

component of the water heater. Replacement components will

be warranted for ninety (90) days.

B. Should a defect or malfunction result in a leakage of water

from the water heater within the  rst six (6) years after the

original date of installation due to defective material or

workmanship, malfunction, or failure to comply with the

above warranty, with such defect or malfunction having been

veri ed by an authorized representative of the manufacturer,

the manufacturer will repair or replace, at its option, the

defective or malfunctioning water heater. Replacements will

be of the nearest comparable model available at the time of

replacement. The replacement water heater will be warranted

for the unexpired portion of the applicable warranty period of

the original water heater.

C. In the event of a leakage of water of a replacement water

heater due to defective material or workmanship, malfunction,

or failure to comply with the above warranty, the manufacturer

reserves the right to refund to the Owner the published

wholesale price available at the date of manufacture of the

original water heater.

D. If government regulations, industry certi cation, or

similar standards require the replacement water heater or

component(s) to have features not found in the defective

water heater or component(s), the Owner will be charged the

di erence in price represented by those required features. If the

Owner pays the price di erence for those required features and/

or to upgrade the size and/or other features available on a new

replacement water heater or component(s), the Owner will also

receive a complete new limited warranty for that replacement

water heater or component(s).

E. If at the time of a request for service the Owner cannot provide

a copy of the original sales receipt or the warranty registration,

the warranty period for the water heater shall then be deemed

to have commenced on the date of manufacture of the water

heater and NOT the date of installation of the water heater, and

be covered by the unexpired portion of the warranty detailed

above.

F. This warranty extends only to water heaters utilized in

water heating applications that have been properly installed

by quali ed professionals based upon the manufacturer’s

installation instructions.

G. It is expressly agreed between the manufacturer and the

Owner that repair, replacement, or refund are the exclusive

remedies of the Owner.

OWNER RESPONSIBILITIES

The Owner or Quali ed Installer / Service Technician must:

1. Have a relief valve bearing the listing marks of the American

Society of Mechanical Engineers (ASME) installed with the water

heater assembly in accordance with federal, state, and local

codes.

2. Have a vacuum relief valve certi ed to ANSI Z21.22 - Relief

Valves for Hot Water Supply Systems - installed with the water

heater assembly in accordance with federal, state, and local

codes and in installations prone to vacuum related damages.

3. Maintain the water heater in accordance with the maintenance

procedure listed in the manufacturer’s provided instructions.

Preventive maintenance can help avoid any unnecessary

breakdown of the water heater and keep it running at optimum

e ciency.

4. Maintain all related system components in good operating

condition.

5. Use the water heater in an open system, or in a closed system

with a properly sized and installed thermal expansion tank.

6. Use the water heater at water pressures not exceeding the

working pressure shown on the rating plate.

7. Keep the water heater free of damaging scale deposits.

8. Make provisions so if the water heater or any component or

connection thereto should leak, the resulting  ow of water will

not cause damage to the area in which it is installed.

WARRANTY EXCLUSIONS

This limited warranty will not cover:

1. Any water heater purchased from an unauthorized dealer.

2. Any water heater not installed by a quali ed heating installer

/ service technician, or installations that do not conform to ANSI,

CSA, and/or UL standards, as well as any applicable national or

local building codes.

3. Service trips to teach the Owner how to install, use, maintain,

or to bring the water heater installation into compliance with

local building codes and regulations.

4. The workmanship of any installer. The manufacturer disclaims

and does not assume any liability of any nature caused by

improper installation, repair, or maintenance.

5. Electricity or fuel costs, or increased or unrealized savings for

same, for any reason whatsoever.

6. Any water damage arising, directly or indirectly, from any

defect in the water heater or component part(s) or from its use.

7. Any incidental, consequential, special, or contingent damages

or expenses arising, directly or indirectly, from any defect in the

water heater or the use of the water heater.

8. Failure to locate the water heater in an area where leakage

of the tank or water line connections and the relief valve will

not result in damage to the area adjacent to the water heater

or lower  oors of the structure, as well as failure to install the

water heater in or with a properly sized drain pan routed to an

approved drainage location.

9. Any failed components of the system not manufactured by

the manufacturer as part of the water heater.

10. Water heaters repaired or altered without the prior written

approval of the manufacturer.

11. Damages, malfunctions, or failures resulting from improper

installation, or failure to install the water heater in accordance

with applicable building codes/ordinances or good plumbing

and electrical trade practices; or failure to operate and maintain

the water heater in accordance with the manufacturer’s

provided instructions.

12. Damages, malfunctions, or failures resulting from failure

to operate the water heater at pressures not exceeding the

working pressure shown on the rating label.

13. Failure to operate the water heater in an open system, or

in a closed system with a properly sized and installed thermal

expansion tank.

14. Failure or performance problems caused by improper sizing

of the water heater, expansion device, piping, electric service

voltage, wiring or fusing.

15. Damages, malfunctions, or failures caused by lack of anode

rod maintenance.

16. Damages, malfunctions, or failures resulting from vacuum

conditions.

17. Damages, malfunctions, or failures caused by operating

the water heater with modi ed, altered, or unapproved

components, or any component / attachment not supplied by

the manufacturer.

18. Damages, malfunctions, or failures caused by abuse,

accident,  re,  ood, freeze, lightning, electrochemical reaction,

acts of God and the like.

19. Tank failures (leaks) caused by operating the water heater in

a corrosive or contaminated atmosphere.

20. Damages, malfunctions, or failures caused by operating the

water heater with an empty or partially empty tank (“dry  ring”),

or failures caused by operating the water heater when it is not

supplied with potable water, free to circulate at all times.

21. Failure of the heater due to the accumulation of solid

materials or lime deposits.

22. Any damage or failure resulting from improper water

chemistry, or heating anything other than potable water.

23. Production of noise, taste, odors, discoloration, or rusty

water.

24. Water heaters replaced for cosmetic reasons.

25. Components of the water heater that are not defective,

but must be replaced during the warranty period as a result of

reasonable wear and tear.

26. Components of the water heater that are subject

to warranties, if any, given by their manufacturers; the

manufacturer does not adopt these warranties.

27. Damages, malfunctions, or failures resulting from the use of

any attachment(s) not supplied by the manufacturer.

28. Water heaters installed outside the  fty states (and the

District of Columbia) of the United States of America and

Canada.

29. Water heaters moved from the original installation location.

30. Water heaters that have had their rating labels removed.

PROCEDURES FOR WARRANTY SERVICE REQUESTS

Any claim for warranty assistance must be made promptly.

Determine if the water heater is “in-warranty” (that is, within the

applicable warranty period) by reviewing a copy of the original

sales receipt or warranty registration. The Owner must present

a copy of the original sales receipt or warranty registration for a

warranty service request.

If the water heater is “in-warranty”, contact the retailer from

whom the water heater was purchased (or the installer) for

assistance. Be prepared to provide the retailer or installer with a

copy of the original receipt, complete model and serial numbers,

and the date of installation of the water heater, in addition to

explanation of the water heater problem.

Warranty coverage is subject to validation of “in-warranty”

coverage by the manufacturer claims department personnel.

All alleged defective or malfunctioning components must be

returned to the manufacturer via the local distribution channels

where original purchase was made. NOTE: Any components or

heaters returned to the manufacturer for warranty analysis

will become the property of the manufacturer and will not

be returned, even if credit is denied. If all warranty conditions

are satis ed, the manufacturer will provide replacement

components to the retailer.

For questions about the coverage of this warranty, please

contact the manufacturer at the following address or phone

number: HTP (an Ariston Thermo Group Company), 272

Duchaine Blvd, New Bedford, MA, 02745

Attention: Warranty Service Department, 1 (774) 271 3108

SERVICE, LABOR, AND SHIPPING COSTS

Except when speci cally prohibited by the applicable state law,

the Owner, and not the Manufacturer, shall be liable for and

shall pay for all charges for labor or other expenses incurred

in the removal, repair, or replacement of the appliance or any

component part(s) claimed to be defective or any expense

incurred to remedy any defect in the product. Such charges

include, but are not necessarily limited to:

1. All freight, shipping, handling, and delivery costs of

forwarding a new appliance or replacement part(s) to the

owner.

2. All costs necessary or incidental in removing the defective

appliance or component part(s) and installing a new appliance

or replacement part(s).

3. All administrative fees incurred by the Owner, as well as

material required to complete, and/or permits required for,

installation of a new appliance or replacement part(s), and

4. All costs necessary or incidental in returning the defective

water heater or component part(s) to a location designated by

the manufacturer.

LIMITATIONS OF YOUR WARRANTY AND REMEDIES

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN

AND ACCEPTED TO THE FURTHEST EXTENT UNDER APPLICABLE

LAW IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY,

RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER

OR NOT ARISING FROM THE MANUFACTURER’s NEGLIGENCE,

ACTUAL OR IMPUTED. THE REMEDIES OF THE OWNER SHALL

BE LIMITED TO THOSE PROVIDED HEREIN TO THE EXCLUSION

OF ANY OTHER REMEDIES INCLUDING WITHOUT LIMITATION,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SAID INCIDENTAL

AND CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED

TO, PROPERTY DAMAGE, LOST PROFIT OR DAMAGES ALLEGED TO

HAVE BEEN CAUSED BY ANY FAILURE OF THE MANUFACTURER

TO MEET ANY OBLIGATION UNDER THIS AGREEMENT INCLUDING

THE OBLIGATION TO REPAIR AND REPLACE SET FORTH ABOVE.

NO AGREEMENT VARYING OR EXTENDING THE FOREGOING

WARRANTIES, REMEDIES OR THIS LIMITATION WILL BE BINDING

UPON THE MANUFACTURER. UNLESS IN WRITING AND SIGNED

BY A DULY AUTHORIZED OFFICER OF THE MANUFACTURER. THE

WARRANTIES STATED HEREIN ARE NOT TRANSFERABLE AND

SHALL BE FOR THE BENEFIT OF THE OWNER ONLY.

NO OTHER WARRANTIES

This warranty gives the Owner speci c legal rights. The Owner may

also have other rights that vary from state to state. Some states do

not allow the exclusion or limitation of incidental or consequential

damages so this limitation or exclusion may not apply to the Owner.

These are the only written warranties applicable to the water heater

manufactured and sold by the manufacturer. The manufacturer

neither assumes nor authorizes anyone to assume for it any other

obligation or liability in connection with said water heaters.

The manufacturer reserves the right to change speci cations or

discontinue models without notice.

Customer Installation Record Form

The following form should be completed by the quali ed installer / service technician for you to keep as a

record of the installation in case of a warranty claim. After reading the important notes at the bottom of the

page, please also sign this document.

Customer’s Name

Date of Installation

Installation Address

Product Model / Serial

Number(s)

Comments

Installer’s Code / Name

Installers Phone Number

Signed by Installer

Signed by Customer

Installation Notes

IMPORTANT

Customer: Please only sign after the quali ed installer / service technician has fully reviewed the installation,

safety, proper operation, and maintenance of the system. If the system has any problems please call the quali ed

installer / service technician. If you are unable to make contact, please call your sales representative.

Distributor / Dealer: Please insert contact details.

La page charge ...

Ariston ANDRIS RS 8U 1.4KW Manuel utilisateur

Marque: Ariston

Modèle: ANDRIS RS 8U 1.4KW

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Ce manuel convient également à

ANDRIS RS 2.5U 1.4KW

Télécharger le PDF

rapport

dans d''autres langues

English: Ariston ANDRIS RS 8U 1.4KW User manual
español: Ariston ANDRIS RS 8U 1.4KW Manual de usuario

Ariston ANDRIS RS 8U 1.4KW Manuel utilisateur

Ce manuel convient également à

Ariston ANDRIS RS 8U 1.4KW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents