BALDR B0359WST2H2PR-V1 Manuel utilisateur

USER MANUAL MODEL:B0359WST2H2PR-V1

(US VERSION)

WIRELESS COLOR WEATHER STATION

WITH MOON PHASE

For the start-up of this device:

Main unit by Ac adaptor (included) and 1x CR2032 (included)

Sensor by 2 x AA batteries (not included)

We thank you for your purchase of Baldr wireless color weather

station with moon phase.It has been designed and constructed

using innovative components and techniques to enable the perfect

display. Please read the instructions carefully to become familiar

with the properties and functions before you use the unit.

1

EN

MAIN UNIT

2

OVERVIEW

13

14

15

16

17

18

1

12

2

10

6

7 11

9

8

5

4

3

19

20

21

1. Temperature and humidity

of Channel 1/2/3

2. Max/min record of Channel

1/2/3

3. Indoor temperature and

humidity

4. Max/min record of indoor

temperature and humidity

13. “ SET ” button

Switch C/F or enter into time

setting

14. “ MEM ” button

Check or clear Max/min

record

15.“ CH ” button

EN

3

1. The default year is 2020, if the weekday display is incorrect .

Please confirm year was set correctly. (for manual setting only)

2. The CR2032 cell battery is for memory function (included). Please

do not used as power supply. If you need to replace the cell battery,

please take out the part device as shown in the figure below, load

new battery matching the polarity(+and-).

5. Three comfort level

indication

6. Weather forecast

Weather forecast for next

12-24 hours

7. Barometric Pressure

Barometer display in mmHg,

inHg or hPa/mb

8. Calendar display

Weekdays in 7 languages

9. Current time

12/24 hour format selectable

10.Channel scan

11.Frost-point warning

12. “ ” button

Notes:

16. “ ▲” button

Indoor temperature/humidity

and barometric calibration or

Increase the data

17. “ ▼/RCC ” button

RCC function or decrease the

data

18. “ ” button

Check alarm time, turn on/off

alarm, enter into alarm setting

19. Stand bracket

20. Hanging Hole

21. Battery Compartment

Switch channel or clear sensors

data and re-registration

Pick out Positive

pole

EN

4

FEATURES

WARNING: THIS PRODUCT CONTAINS A BUTTON-CELL

BATTERY. IF SWALLOWED, IT COULD CAUSE SEVERE INJURY

OR DEATH IN JUST 2 HOURS.SEEK MEDICAL ATTENTION

IMMEDIATELY IF INGESTED.

OUTDOOR SENSOR

1. Signal light 2. Hanging hole

3. Battery compartment 4. Channel 1-2-3 switch

•Clear color LCD display

•WWVB atomic time

•Weather forecast for next 12-24 hours with barometer

•Measures in/out humidity and temperature ( / )

•Up to 3 RF channels for outdoor sensors (only one sensor included)

• Max/min record of temperature & humidity

12

3

4

EN

5

PACKAGE CONTENT

GETTING START

MAIN UNIT INSTALLATION

BALDR recommends high quality alkaline or lithium batteries

for the best product performance. Heavy duty or rechargeable

batteries are not recommended.

•Comfort level indication

•Indoor temperature range: 14 ~122 (-10 ~50 )

•Outdoor temperature range:-40 ~140 (-40 ~60 )

•In/outdoor humidity range: 1%-99%

•Calendar, alarm and snooze function

•Time display in 12/24H

•Calendar function with Month/Date or Date/Month display format

selectable

•White backlight with dimmer

Following contents are included in the package:

1 x Weather Station Main Unit

1 x Remote Sensor

1 x AC Adaptor

1 x CR2032 Cell Battery

1 x User Manual

Remove the cell battery’s Insulating strip, then plug the adaptor to a

powered outlet.

SENSOR INSTALLATION

1. Remove the battery compartment cover;

2. Insert 2 x AA batteries in each sensor matching the polarity (+and-);

3. Replace the battery cover.

EN

6

After power on, It will start receiving outdoor sensor’ signal for 3

minutes. If signal received within 3 minutes or receiving window ends,

it will enter into DCF signal receiving window.

SENSOR SETUP

RF Signal Receiving

1. After RF signal receiving, it will start searching radio signal for 7

minutes with the antenna symbol “ ” displaying on screen.

Meanwhile, the backlight brightness will automatically adjust to 5%

(default brightness: 100%).

DCF Signal Receiving

MAIN UNIT SETUP

When power on or reset, LCD will full display for 3 seconds

with “BI” sound. Then display Indoor temperature and

humidity, barometric pressure with 100% backlight brightness.

● Switch the Channel 1-2-3 of the senor to any channel you want.

For example, you can set to Channel 1 for the sensor. But please

ensure the main unit are set to the same channel before

synchronization. (Special note: Press “CH” button on the main unit

to set the channel.The setting order is CH1--CH2--CH3--Channel

scan (from CH1 to CH2 to CH3,10 seconds intervals),you must

select the same number choices for both the sensor and the main

unit in order for the units to synchronize).

● Power the main unit prior to load the batteries of sensor.

Note: 1. Main unit will auto receive outdoor signal after power on, the

receiving status will last for max 3 minutes. The receiving

antenna signal will flash. If no signal received in 3 minutes,

it will stop receiving outdoor signal.

2. If the main unit is out of 3 minutes’ signal receiving window,

you can press and hold the “ CH ” button to enter signal

receiving again.

EN

7

1. After signal received, if there is no need for other settings, you can

just finish reading here. If there is other setting requirements.

Please check the following steps. Or if there is no signal received,

you can follow bellow steps for manual setting.

2. Press and hold “ SET ” button to enter into setting, press “ SET ”

button to skip setting steps or go to the next setting option.

*Tips: press and hold “▲” or “ ▼/RCC ” button will quickly

change the value by 8 steps.

3. Press “ SET ” to select the RCC. Default setting : ON. Press “▲” or

“ ▼/RCC ” button to select OFF or ON.

4. Press “ SET ” to select Time Zone. Default setting : -5(EST). Press

“▲” or “ ▼/RCC ” button to select time zone: AST(-4),EST(-5),CST

(-6),MST(-7),PST(-8),AKT(-9),HAT(-10) optional.

Manual Settings

2. Once signal received, the main unit will display the received time/

month/date/weekday with symbol “ ” displaying on screen.

3. Daily RCC signal receiving: there are regular radio signal receiving

at UTC 7:00AM,8:00AM, 9:00AM, 10:00AM, 11:00AM each day. It

starts receiving signal at UTC 7:00AM everyday. For each day,

once signal received at any one receiving time, it will stop receiving

signal that day.

4. Manual receiving: press and hold “ ▼/RCC ” button to enter RCC

signal receiving.

5. During receiving, press “ ▼/RCC ” button to exit RCC receiving.

*RCC symbol display:

a. When receiving signal , RCC icon will be flashing by“1HZ”.

b. When signal successfully received, LCD will display complete

RCC icon and exit RCC receiving.

c. If no signal is received, the RCC icon will disappear.

Time

Zone

AST

Atlantic

EST

Eastern

CST

Central

MST

Mountain

PST

Pacific

AKT

Alaskan

HAT

Hawaiian

EN

8

5. Press “ SET ” to select DST ON/OFF. Default setting : ON. Press

“▲” or “ ▼/RCC ” button to select DST ON if you do observe

Daylight Saving Time.

6. Press “ SET ” to select 12/24H Time Format. Default setting :12 H.

Press the “▲” or “ ▼/RCC ” button to select 12H or 24H.

7. Press “ SET ” to select Hours. Press “▲” or “ ▼/RCC ” button to

adjust the value.

8. Press “ SET ” to select Minutes. Press “▲” or “ ▼/RCC ” button to

adjust the value.

9. Press “ SET ” to select Year. Press “▲” or “ ▼/RCC ” button to

adjust the value.

10. Press “ SET ” to select Month&Date display format. Default

setting : M/D. Press the “▲” or “ ▼/RCC ” button to select M/D or

D/M format. (M: Month ,D: Date)

11. Press “ SET ” to select the Month. Press “▲” or “ ▼/RCC ” button

to adjust the value.

12. Press “ SET ” to select the Date. Press “▲” or “ ▼/RCC ” button

to adjust the value.

13. Press “ SET ” to select Weekday Language. Default setting :ENG.

Press the “▲” or “ ▼/RCC ” button to select languages: GER/

ENG/FRE/SPA/ITA/DUT/DAN optional .(German/English/French/

Spanish/Italian/Dutch/Danish)

14. Press “ SET ” to select Beep ON/OFF .Default setting :ON. Press

the “▲” or “ ▼/RCC ” button to select ON/OFF.

15. Press “ SET ” to select the Barometric Unit. Default setting : inHg.

Press “▲” or “ ▼/RCC ” button to select unit: mmHg, inHg or hPa/

mb optional.

DST symbol display:

a. Select “DST ALWAYS” ,means DST function is always on all

the year round.

b. Select “DST ”,means DST function will be on during daylight

saving time.

c. Select “DST OFF”, means DST function is off.

EN

1. Press and hold “ ” button to enter into alarm time and snooze

setting.

2. Press “▲” or “ ▼/RCC ” button to adjust data; press and hold “▲”

or “ ▼/RCC ” button will quickly change the value by 8 steps.

3. The setting order is: Hour → Minute→Snooze Interval time → Exit.

4. Snooze interval time : 5~60 minutes can be set, Default setting :

5 minutes.

ALARM FUNCTION

Alarm Time & Snooze Setting

9

1. When in time display mode, press “ ” button to check alarm time.

Press “ ” button twice to turn ON/OFF alarm by the ON/OFF of

symbol .

2. When in alarm time display mode, press “ ” button to turn on/off

the alarm by the ON/OFF of symbol .

Alarm ON/OFF Setting

1. When the alarm is ringing, press any other button except top button

to stop the alarm. And the alarm will restart next day.

2. Or when alarm is ringing, press the top button to activate snooze

function. The alarm will ring again in snooze interval time as you

SNOOZE FUNCTION

5. During setting, touch top button to save and exit setting.

6. During setting, if no operation for 20 seconds, it will automatically

save and exit setting.

7. The alarm is default ON after setting the alarm time. Alarm symbol

will display on screen.

16. Press “ SET ” to confirm and exit.

17. During setting, touch top button to save and exit setting.

18. During setting, if no operation for 20 seconds, it will automatically

save and exit setting.

EN

10

OPERATION GUIDELINES

1. After power on ,the indoor temperature will display automatically, it

will update reading each 30 seconds and start to receive outdoor

signal which lasts for max 3 minutes.

2. Indoor temperature display range:14 ~ 122 (-10 ~ 50.0 ); for

temperature lower than 14 ,the reading will be :“LL.L”; for

temperature higher than 122 ,the reading will be :“HH.H”.

3. Outdoor temperature display range :-40 ~140 (-40 ~60 ); for

temperature lower than -40 ,the reading will be :“LL.L”; for

temperature higher than 140 ,the reading will be :“HH.H”.

4. Arrow indication for temperature changes:

TEMPERATURE

1. Press “MEM” button to check maximum temperature and humidity,

the value will display for 5 seconds.

2. Press “MEM” button second time to check the minimum

temperature and humidity, the value will display for 5 seconds.

3. Press “MEM” button third time will return to standard mode.

MAX AND MIN RECORD

set before. And the “ ” symbol will be flashing on screen to

indicate the snooze mode. Press any other button except top

button to exit the snooze mode. And the alarm will restart next day.

3. When alarm rings, the ascending “Bibi” alarm sound will last for 2

minutes if no operation.

4. Press and hold “MEM” button will clear the max and min record

and reactivate the memory.

5. During setting, if no operation for 5 seconds, it will automatically

save and exit setting.

6. Normally, the Max and Min record will update every 24 hours at

0:00.

EN

will display when temperature changes less than 1.8 within one

hour or compared with last reading;

will display when the reading increase by 1.8 within one hour or

compared with last reading.

will display when the reading decrease by 1.8 within one hour or

compared with last reading.

5. Accuracy: For temperature between 32 ~122 ,the accuracy is

±1.8 ,if out of this range the accuracy will be ±3.6 ;

Temperature resolution is 0.1 (0.1 ).

6. Press “SET ” button to switch from Celsius degree to Fahrenheit

degree.

1. After power on ,the indoor humidity will display automatically, it will

update reading each 30 seconds and start to receive outdoor

signal which lasts for max 3 minutes.

2. Humidity display range: 1%-99%;for humidity lower than 1%,the

reading will be “1%”;for humidity higher than 99%,the reading will

be “ 99%”.

3. Accuracy: when the temperature is between 68 ~ 78.8 (20 ~

26 ) and the humidity is between 40-80%,the accuracy is ±5%,if

out of this range the accuracy will be ±8%.

4. Arrow indication for humidity changes:

will display when humidity changes less than 5% RH within one

hour or compared with last reading.

will display when the reading increase by 5% RH within one hour

or compared with last reading.

will display when the reading decrease by 5% RH within one hour

or compared with last reading.

5. Humidity resolution:1% .

HUMIDITY

11

EN

12

1. Barometer range: 25.1-31inHg (646-798mmHg, 850-1050 hPa/mb).

2. Arrow indication for barometric pressure changes:

will display when pressure changes less than 2 hPa within three

hour or compared with last reading;

will display when the pressure increase by 2 hPa within three hour

or compared with last reading.

will display when the pressure decrease by 2 hPa within three hour

or compared with last reading.

3. Press and hold “SET ” button to switch barometric unit ( please

refer to Manual Settings Point 15) .

BAROMETRIC PRESSURE

WEATHER FORECAST

COMFORT LEVEL INDICATOR

● The weather forecast icon will show after power on. There are 5

kinds of weather modes: Sunny, Sunny To Cloudy, Cloudy, Rainy,

Snow. The weather icon displays are based on the hourly

calculation of indoor/outdoor temperature & humidity and barometer

data. The forecast is for next 12 hours with 70%-75% accuracy.

Display

Humidity DRY 1%- 39% COMFORT 40%-70% WET 71%-99%

Sunny Sunny To Cloudy Cloudy Rainy Snow

EN

13

1. When in time display mode, press and hold “▲” button to enter

Calibration mode.

2. Press and release the “SET” button to confirm and move to the

next setting: Indoor Temperature →Indoor Humidity→ Barometer

→Exit.

3. Press “▲ ” or “ ▼/RCC ” button to adjust the value.

4. Indoor temperature calibration range : ±5 ;

Indoor humidity calibration range: ± 10 %RH;

Barometer calibration range: ±10 hPa.

5. During setting,you can press “MEM” button to clear all correction

values.

FROST-POINT ALERT

MOON PHASE

CALIBRATION

Baldr weather stations were calibrated precisely at our

manufacturing facility, but if you want the data of this product

to be consistent with the reading of the equipment you are

more trusted or more used to, you can manually calibrate the

indoor temperature, humidity and barometer values.

• When current outdoor channel’s temperature is in the range of 32

~37.22 (0 ~ 2.9 ),the alert symbol “ ” will be flashing until

the temperature reading is higher than 37.22 ; the symbol will

keep displaying on screen if temperature is lower than 32 .

New Moon Waxing Crescent First Quarter Waxing Gibbous

Full Moon Waning Gibbous Last Quarter Waning Crescent

EN

14

ADJUSTABLE BACKLIGHT

● After powering on, touch “ ” button to adjust the brightness

of the backlight.

● Backlight brightness can be selected from 5%,60%,100% and off.

6. During setting, touch top button to save and exit setting. If no

operation for 20 seconds, it will automatically save and exit setting.

LOW BATTERY INDICATORS

● About Outdoor Sensor: When battery indicator shows next to the

outdoor temperature, replace batteries in your outdoor sensor.

● About Cell Battery in Main Unit: The CR2032 cell battery is only for

memorizing the setting during sudden power outage. When battery

indicator shows next to your Indoor Temperature, replace battery.

No outdoor sensor

reception

1. Reload the batteries of both outdoor sensor and

main unit. Please refer to the SENSOR SETUP

section.

2. Relocate the main unit and/or the outdoor sensor.

TROUBLE SHOOTING

Problem

Outdoor reading is

flashing or showing

dashes

Flashing of the outdoor reading is generally an

indication of wireless interference.

1. Bring both the sensor and display indoors, side

by side and remove batteries from each.

2. Make sure the 1-2-3 switch on both units match.

3. Reload batteries in outdoor sensor.

4. Reload batteries in main unit.

5. Let both units sit within a couple feet of each

other for a few minutes to gain a strong

connection before taking sensor to outdoor area.

Possible Solution

EN

15

PLACEMENT INSTRUCTION

BALDR sensors are sensitive to surrounding environmental

conditions. Proper placement of both the main unit and

outdoor sensor are critical to the accuracy and performance

of this product.

Main Unit Placement

Place main unit in a dry area free of dirt and dust. To help ensure an

accurate indoor temperature measurement, be sure to place the Main

unit away from heat sources or vents.

If your BALDR product does not operate properly after trying the

troubleshooting steps, please contact the seller on your order page or

shoot an email to: [email protected].

Inaccurate

temperature/

humidity

The units must be within 328ft(100m) of each

other.

3. Make sure both units are placed at least 3 ft (0.9

m) away from electronics that may interfere

with the wireless communication (such as TVs,

microwaves, computers, etc).

4. Use standard alkaline batteries. Do not use

heavy duty or rechargeable batteries. NOTE: It

may take a few minutes for main unit and sensor

to synchronize after batteries are reloaded.

Make sure both the main unit and sensor are placed

out of direct sunlight and away from any heat

sources or vents.

“HH.H/LL.L” display

in indoor and/or

outdoor

temperature

If the temperature is higher than the detection range,

“HH.H” will display on screen for indication; if lower

than the detection range, “LL.L” will display on

screen for indication.

EN

16

PRECAUTIONS

Outdoor Sensor Placement

Sensor must be placed outside to observe outdoor conditions.

Sensor is water resistant for water splashes and is designed for

general outdoor use, however, to extend its life place the sensor in an

area protected from direct weather elements. The best location is 4 to

8 feet (1.2 to 2.4 meters) above the ground with permanent shade and

plenty of fresh air to circulate around the sensor.

Important Placement Guidelines

● The distance between main unit and transmitter should be at least

5~6.5 feet (1.5~2 meters) away from any interfering sources such

as computer monitors or TV sets.

● To maximize wireless range, place units away from large metallic

items, thick walls, metal surfaces, or other objects that may limit

wireless communication.

● Please do not use other electrical products such as headphones or

speakers operating on the same signal frequency.

● Neighbors using electrical devices operating on the same signal

frequency can also cause interference.

● Do not clean any part of the product with benzene, thinner or other

solvent chemicals. When necessary, clean it with a soft cloth.

● Never immerse the product in water. This can cause electrical shock

and damage the product.

● Do not subject the product to extreme force, shock, or fluctuations in

temperature or humidity.

● Do not tamper With the internal components.

● Do not mix new and old batteries or batteries of different types.

● Do not mix alkaline, standard or rechargeable batteries with this

product.

Remove the batteries if storing this product for a long period of time.

EN

17

Warranty

BALDR provides a 1-year limited warranty on this product against

manufacturing defects in materials and workmanship.

Warranty service can only be performed by our authorized service

center. The original dated bill of sale must be presented upon request

as proof of purchase to us, or our authorized service center.

The warranty covers all defects in material and workmanship with the

following specified exceptions:(1) damage caused by accident,

unreasonable use or neglect (including the lack or reasonable and

necessary maintenance); (2) damage occurring during shipment

(claims must be presented to the carrier); (3) damage to, or

deterioration of any accessory or decorative surface;(4) damage

resulting from failure to follow instructions contained in your owner’s

manual.

This warranty covers only actual defects within the product itself, and

does not cover the cost of installation or removal from a fixed

installation, normal set-up or adjustments, claims based on

misrepresentation by the seller or performance variations resulting

from installation-related circumstances.

To receive warranty service, the purchaser must contact with BALDR

nominated service center for the problem determination and service

procedure.

Thank you for your choice of BALDR products!

● Do not dispose of this product as unsorted municipal waste.

Collection of such waste separately for special treatment is

necessary.

EN

18

MANUEL D'UTILISATION MODÈLE:

B0359WST2H2PR-V1 (VERSION US)

STATION MÉTÉO COULEUR SANS FIL AVEC

PHASE DE LUNE

Pour la mise en service de cet appareil :

Unité principale par adaptateur CA (inclus) et 1x CR2032 (inclus)

Capteur par 2 x piles AA (non incluses)

Nous vous remercions pour votre achat de la station météo couleur

sans fil Baldr avec phase de lune.Elle a été conçue et construite en

utilisant des composants et des techniques innovants pour permettre

un affichage parfait. Veuillez lire attentivement les instructions afin

de vous familiariser avec les propriétés et les fonctions avant

d'utiliser l'appareil.

FR

19

UNITÉ PRINCIPALE

VUE D'ENSEMBLE

13

14

15

16

17

18

1

12

2

10

6

7 11

9

8

5

4

3

19

20

21

1. Température et humidité du

canal 1/2/3

2. Enregistrement max/min du

canal 1/2/3

3. Température et humidité

intérieures

4. Enregistrement max/min de

la température et de

l'humidité intérieures

14. Bouton "MEM"

Vérifier ou effacer

l'enregistrement Max/min

15. Bouton "CH"

13. Bouton "SET"

Changer de C/F ou entrer

dans la mise à l'heure

FR

20

1. L'année par défaut est 2020, si l'affichage du jour de la semaine

est incorrect. (uniquement pour le réglage manuel)

2. La pile CR2032 pour la fonction mémoire (incluse), ne doit pas être

utilisée comme source d'alimentation. Si vous devez remplacer la

pile, veuillez retirer la pièce de l'appareil comme indiqué sur la

figure ci-dessous, puis chargez une nouvelle pile correspondant à

celle de polarity +and-).

5. Indication des trois niveaux

de confor

6. Prévisions météorologiques

Prévisions météorologiques

pour les prochaines 12-24

heures

7. Pression barométrique

Affichage du baromètre en

mmHg,inHg ou hPa/mb

8. Affichage du calendrier

Les jours de la semaine en

7 langues

9. heure actuelle

Format 12/24 heures

sélectionnable

10. balayage des chaînes

11. alerte au gel

12. “ ” button

17. Bouton “ ▼/RCC ”

de fonction RCC ou diminuer

les données

18. Bouton “ ”

Vérifier l'heure de l'alarme,

activer/désactiver l'alarme,

entrer dans le réglage de

l'alarme

19. Support

20. Trou de suspension

21. Compartiment des piles

Notes :

Température / humidité

intérieure et étalonnage

barométrique ou augmenter

les données

Effacer les données des

capteurs et réenregistrer

16. Bouton “ ▲”

FR

La page charge ...

BALDR B0359WST2H2PR-V1 Manuel utilisateur

BALDR B0359WST2H2PR-V1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents