AFG 18.1AXT Le manuel du propriétaire

ELLIPTICAL OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DE L’EXERCISEUR ELLIPTIQUE

MANUAL DEL PROPIETARIO DE LA MÁQUINA ELÍPTICA

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.

Lire le GUIDE D’UTILISATION DE L’EXERCISEUR ELLIPTIQUE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.

Lea la GUÍA DEL USUARIO DE LA MÁQUINA ELÍPTICA antes de usar este MANUAL DEL PROPIETARIO.

18.1AXT

181AXT_OM_Rev1_6.indd 1 7/22/11 2:28 PM

2 3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following: Read all instructions

before using this elliptical. It is the responsibility of the owner to ensure that all users of this elliptical are adequately informed of

all warnings and precautions. If you have any questions after reading this manual, contact Customer Tech Support at the number

listed on the back panel.

This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional setting.

Failure to comply will void the warranty.

3 ENGLISH

44 FRANÇAIS

86 ESPAÑOL

181AXT_OM_Rev1_6.indd 2-3 7/22/11 2:28 PM

4 5

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the elliptical from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking

off parts.

DANGER

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop

exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace. Do not sprint above 80 RPMs on this machine.

• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting the machine.

• Do not turn pedal arms by hand.

• Make sure handlebars are secure before each use.

• Keep the topside of the foot support clean and dry.

• Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on the

mounting or dismounting side to its lowest position and bring the machine to a complete stop.

• Do not wear clothes that might catch on any part of the elliptical.

• Always wear athletic shoes while using this equipment.

• Do not jump on the elliptical.

• At no time should more than one person be on the elliptical while in operation.

• This elliptical should not be used by persons weighing more than the specified user capacity in the OWNER’S MANUAL

WARRANTY SECTION. Failure to comply will void the warranty.

• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional setting.

Failure to comply will void the warranty.

• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,

bathrooms, car ports or outdoors. Failure to comply will void the warranty.

• To prevent electrical shock, never drop or insert any object into any opening.

• Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Use the elliptical only as described in the elliptical guide and owner’s manual.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth

only; never use solvents. (See MAINTENANCE)

• The elliptical should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or

taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• At NO time should pets or children under the age of 13 be closer to the elliptical than 10 feet.

• At NO time should children under the age of 13 use the elliptical.

• Children ove

r the age of 13 or disabled persons should not use the elliptical without adult supervision.

• Never operate the elliptical if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or

immersed in water. Return the elliptical to a service center for examination and repair.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized

service technician

It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed to colder

temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room temperature before

first time use. Failure to do so may cause premature electronic failure.

WARNING

181AXT_OM_Rev1_6.indd 4-5 7/22/11 2:28 PM

6 7

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly

instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the

elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to

the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your elliptical’s serial number located on a white barcode sticker

on the front stabilizer tube and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

WARNING

SERIAL NUMBER:

EP

MODEL NAME: AFG 18.1AXT ELLIPTICAL

SERIAL NUMBER LOCATION

GROUNDING INSTRUCTIONS

If your elliptical has power incline with a 3-prong plug, you must follow these grounding instructions.

This product must be grounded. If a elliptical should malfunction or break down, grounding provides a path of least resistance

for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with local codes and ordinances.

Connect this exercise product to a properly grounded outlet only.

Never operate product with a damaged cord or plug even if it is working

properly. Never operate any product if it appears damaged, or has been

immersed in water. Contact Customer Tech Support for replacement or repair.

3-POLE

GROUNDED

OUTLET

GROUNDING PIN

WARNING

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified

electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided

with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make

sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this

product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and

observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one

circuit. This elliptical should be used with a minimum 15-amp circuit.

181AXT_OM_Rev1_6.indd 6-7 7/22/11 2:28 PM

8 9

WARNING

CONSULT A PHYSICIAN PRIOR TO USING ANY

EXERCISE EQUIPMENT. POSSIBILITY OF

SERIOUS INJURY IF EQUIPMENT IS USED

IMPROPERLY. READ INSTRUCTION MANUAL

BEFORE USING. KEEP CHILDREN OFF AND

AWAY FROM THIS EQUIPMENT. FOR

CONSUMER USE ONLY.

AVERTISSEMENT

CONSULTER UN MÉDECIN AVANT D’UTILISER

TOUT ÉQUIPEMENT D’EXERCICE. TOUTE

UTILISATION INCORRECTE PEUT OCCASIONNER

DE GRAVES BLESSURES. LIRE LE MANUEL DU

PROPRIÉTAIRE AVANT DE SE SERVIR DE

L’APPAREIL. TENIR LES ENFANTS À DISTANCE DE

L’APPAREIL. À L’USAGE DU CLIENT SEULEMENT.

CONSULTE A UN MÉDICO ANTES DE USAR CUALQUIER

EQUIPO DE ACONDICIONAMIENTO FÍSICO. EXISTE LA

POSIBILIDAD DE SUFRIR LESIONES GRAVES SI EL

EQUIPO SE USA INCORRECTAMENTE. LEER EL

MANUAL DEL PROPIETARIO ANTES DE USAR EL

EQUIPO. NO DEJE QUE LOS NIÑOS SE ACERQUEN A

ESTE EQUIPO. ESTE EQUIPO ES SÓLO PARA EL USO

DEL CONSUMIDOR.

ADVERTENCIA

CAUTION ATTENTION PRECAUCIÓN

KEEP HANDS AND FEET

AWAY FROM THIS AREA.

GARDER LES MAINS ET LES

PIEDS LOIN DE CETTE REGION.

MANTENGA LAS MANOS Y LOS

PIES LEJOS DE ESTA ÁREA.

FOOT PADS

SWING ARM

TOP HAND RAIL

BASE RAIL

SPEAKERS

WATER BOTTLE HOLDER

UPPER HANDLEBAR

PULSE GRIPS

CONSOLE

STABILIZER TUBE

POWER CORD SOCKET

LINK ARM

MAIN FRAME

USB PORT

IPOD/MP3 PLAYER POCKET

CONSOLE MAST

CONSOLE CONTROLS AND DISPLAY WINDOWS

PEDAL ARM

LOWER HANDLEBAR

REAR UPRIGHT

TOOLS INCLUDED:

F Phillips Screwdriver

F 6mm L Wrench

F 5mm L Wrench

F 5mm T Wrench

F 13/15mm Flat Wrench

PARTS INCLUDED:

F 1 Console

F 1 Console Mast

F 1 Water Bottle Holder

F 1 Main Frame

F 1 Front Stabilizer Tube

F 1 Base Rail

F 2 Footpads

F 1 Audio Adaptor Cable

F 3 iPod® Dock Inserts

F 2 Crank Caps

F 2 Upper Hadlebars

F 2 Lower Handlebars

F 2 Swing Arms

F 2 Link Arms

F 2 Pedal Arms

F 2 Rear Uprights

F 2 Top Hand Rails

F 1 AC Adaptor Cable

F 1 Universal MP3 Player Dock Insert

F 1 Polar

®

Chest Strap

UNPACKING

Unpack the product where you will be using it. Place the elliptical carton on a level

flat surface. It is recommended that you place a protective covering on your floor.

Never open box when it is on its side.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place

and partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any

grease, such as lithium bike grease is recommended.

If you have questions or if

there are any missing parts,

contact Customer Tech

Support. Contact information

is located on the back panel

of this manual.

NEED HELP?

PRE ASSEMBLY

181AXT_OM_Rev1_6.indd 8-9 7/22/11 2:28 PM

10 11

ASSEMBLY STEP 1

A Open HARDWARE FOR STEP 1.

B Attach the FRONT STABILIZER TUBE to

the MAIN FRAME using 4 BOLTS (A) and 4

WASHERS (B).

C Attach the BASE RAIL to the MAIN FRAME

using 4 BOLTS (A) and 4 WASHERS (B).

BOLT (A)

20 mm

Qty: 8

FLAT WASHER (B)

20 mm

Qty: 8

HARDWARE FOR STEP 1:

BOLTS (A)

FLAT WASHERS (B)

BASE RAIL

FRONT STABILIZER TUBE

MAIN FRAME

ASSEMBLY STEP 2

A Open HARDWARE FOR STEP 2.

B Attach the REAR UPRIGHTS to the BASE

FRAME using 4 BOLTS (C), 4 WASHERS (D),

4 BASE RAIL BRACKET CAPS and 2 AXLES.

C Partially thread the TOP HANDRAILS to the

REAR UPRIGHTS using 8 BOLTS (C) and 8

ARC WASHERS (E).

WASHER (D)

25 mm

Qty: 4

AXLE

Qty: 2

BOLT (C)

16 mm

Qty: 12

ARC WASHER (E)

17 mm

Qty: 8

SIDE

VIEW

HARDWARE FOR STEP 2:

BOLTS (C)

ARC WASHERS (E)

BOLTS (C)

WASHERS (D)

AXLE

BASE RAIL

TOP HANDRAIL

MAIN FRAME

REAR UPRIGHT

BASE RAIL BRACKET CAPS

NOTE: Assemble the top handrails so they are parallel to the floor. Do not assemble with the top handrail resting on the floor.

Assemble the rear uprights so they curve toward the main frame as illustrated.

181AXT_OM_Rev1_6.indd 10-11 7/22/11 2:28 PM

12 13

ASSEMBLY STEP 3

A Open HARDWARE FOR STEP 3.

B Attach each TOP HANDRAIL to the INCLINE

ARM using 4 BOLTS (F) and 4 NUTS (G). To

make assembly easier, lightly tighten all four

bolts to begin, then tighten firmly after all bolts

have been started.

C Tighten all hardware from ASSEMBLY STEP 2.

BOLT (F)

25 mm

Qty: 4

NUT (G)

8 mm

Qty: 4

HARDWARE FOR STEP 3:

INCLINE ARM

BOLTS (F)

TOP HANDRAIL

NUTS (G)

ASSEMBLY STEP 4

A Open HARDWARE FOR STEP 4.

B Slide 1 WAVY WASHER (J) onto each HANDLEBAR

SHAFT.

C Slide the LEFT LOWER HANDLEBAR onto the

HANDLEBAR SHAFT. Be sure the LEFT LOWER

HANDLEBAR is positioned the same as shown in the

diagram.

D Slide the LEFT UPPER HANDLEBAR onto the

HANDLEBAR SHAFT. Using 4 BOLTS (H) connect

the UPPER AND LOWER HANDLEBARS as shown

in the diagram. Do not tighten any bolts until all 4 are

started.

E Secure the HANDLEBAR ASSEMBLY using 1

WASHER (I) and 1 BOLT (C). NOTE: be sure to

attach WASHER (I) as shown in STEP E diagram.

F Repeat steps B–E on the opposite side.

BOLT (H)

20 mm

Qty: 8

WASHER (I)

34 mm

Qty: 2

BOLT (C)

16 mm

Qty: 2

WAVY WASHER (J)

23 mm

Qty: 2

HARDWARE FOR STEP 4:

BOLTS (H)

BOLT (C)

WASHER (I)

MAIN FRAME

RIGHT UPPER

HANDLEBAR

LEFT UPPER

HANDLEBAR

REAR MAST COVER

HANDLEBAR SHAFT

WAVY WASHE R (J)

LEFT LOWER

HANDLEBAR

RIGHT LOWER

HANDLEBAR

BOLT (C)

WASHER (I)

STEP E DIAGRAM

181AXT_OM_Rev1_6.indd 12-13 7/22/11 2:28 PM

14 15

ASSEMBLY STEP 5

A Open HARDWARE FOR STEP 5.

B Run CONSOLE CABLES from MAIN FRAME

BRACKET through the CONSOLE MAST.

C Attach CONSOLE MAST to the MAIN

FRAME BRACKET using 4 BOLTS (C) and 4

WASHERS (L).

D Attach the CONSOLE CABLES to the

CONSOLE.

E Carefully tuck the CONSOLE CABLES into

the CONSOLE MAST before attaching the

CONSOLE. Attach CONSOLE to CONSOLE

MAST using 4 PRE-ATTACHED BOLTS.

F Attach WATER BOTTLE HOLDER to

CONSOLE MAST using 2 PRE-ATTACHED

BOLTS.

BOLT (C)

16 mm

Qty: 4

WASHER (L)

18 mm

Qty: 4

HARDWARE FOR STEP 5:

PRE-ATTACHED

BOLTS

PRE-ATTACHED

BOLTS

WATER BOTTLE

HOLDER

CONSOLE MAST

BOLTS (C)

CONSOLE CABLES

MAIN FRAME

BRACKET

CONSOLE

WASHER (L)CONSOLE CABLES

ASSEMBLY STEP 6

A Open HARDWARE FOR STEP 6.

B Attach each FOOTPAD to the footpad support

on each LINK ARM using 4 BOLTS (K) and 4

WASHERS (L).

C Repeat on opposite side.

WASHER (L)

18 mm

Qty: 8

BOLT (K)

12 mm

Qty: 8

BOLT (C)

16 mm

Qty: 2

WASHER (P)

38 mm

Qty: 2

WAVY WASHE R (M)

34 mm

Qty: 2

HARDWARE FOR STEP 6:

BOLTS (K)

WASHERS (L)

LINK ARM

FOOTPAD

NOTE: Be careful not to pinch any wires while attaching the

console mast or console.

181AXT_OM_Rev1_6.indd 14-15 7/22/11 2:28 PM

16 17

A Lay waste packaging plastic over the base rail.

This will prevent the pedal arm assembly from

scratching the elliptical’s paint.

B Open HARDWARE FOR STEP 8.

C Attach RIGHT SWING ARM to TOP

HANDRAIL using 2 SWING CAPS, 2 BOLTS

(C), 2 AXLES and 2 WASHERS (D).

D Attach the RIGHT PEDAL ARM to the right

CRANK using 1 WAVY WASHER (J), 1

WASHER (D) and 1 BOLT (C).

E Attach the CRANK CAP to the CRANK.

F Repeat on opposite side.

WASHER (D)

25 mm

Qty: 6

BOLT (C)

16 mm

Qty: 6

WAVY WASHER (J)

29 mm

Qty: 2

AXLE

Qty: 2

HARDWARE FOR STEP 8:

CRANK

PACKAGING PLASTIC

WASHER (D)

WAVY WASHE R (J)

BOLT (C)

CRANK CAP

SWING CAP

TOP HANDRAIL

WASHER (D)

BOLT (C)

AXLE

WASHER (D)

SWING CAP

BOLT (C)

RIGHT SWI NG ARM

RIGHT PE DAL ARM

LINK ARM

ASSEMBLY STEP 8

NOTE: Leave bolts loose until you have

finished STEP D.

ASSEMBLY STEP 7

A Open HARDWARE FOR STEP 7.

B Attach RIGHT LINK ARM to RIGHT PEDAL

ARM using 1 BOLT (C), 1 WASHER (P) and 1

WAVY WASHER (M).

C Repeat on opposite side.

WASHER (L)

18 mm

Qty: 8

BOLT (K)

12 mm

Qty: 8

BOLT (C)

16 mm

Qty: 2

WASHER (P)

38 mm

Qty: 2

WAVY WASHE R (M)

34 mm

Qty: 2

HARDWARE FOR STEP 7:

PEDAL ARM

BOLT (C)

WASHER (P)

WAVY WASHER (M)

LINK ARM

181AXT_OM_Rev1_6.indd 16-17 7/22/11 2:28 PM

18 19

ASSEMBLY STEP 9

NUT (G)

WASHER (L)

BOLT (N)

SPACER

ROD BEARING SHAFT

LINK ARM

LOWER HANDLEBAR

A Open HARDWARE FOR STEP 9.

B Slide ROD BEARING SHAFT into the end of

the LINK ARM. Align end of LINK ARM with

bracket on bottom of LOWER HANDLEBAR.

C Place SPACERS on both sides of the

LINK ARM. While holding SPACERS slide

LINK ARM into bottom end of LOWER

HANDLEBAR.

D Secure the joint using 1 BOLT (N), 1 WASHER

(L) and 1 NUT (G).

E Repeat on opposite side.

HARDWARE FOR STEP 9:

WASHER (L)

18 mm

Qty: 2

BOLT (N)

45 mm

Qty: 2

ROD BEARING

SHAFT

Qty: 2

SPACER

Qty: 4

NUT (G)

8 mm

Qty: 2

ASSEMBLY STEP 10

A Open HARDWARE FOR STEP 10.

B Attach JOINT COVERS to the joint between

the LINK ARM and the LOWER HANDLEBAR

using 3 SCREWS (O).

C Repeat on opposite side.

D Adjust the 2 REAR LEVELERS so that the

machine is level on the floor. Then adjust the

CENTER LEVELER located under the BASE

RAIL just so it is snug with the floor.

SCREW (O)

12 mm

Qty: 6

HARDWARE FOR STEP 10:

JOINT COVERS

LOWER

HANDLEBAR

SCREWS (O)

LINK ARM

REAR LEVELERS

CENTER LEVELER

BASE RAIL

ASSEMBLY COMPLETE!

181AXT_OM_Rev1_6.indd 18-19 7/22/11 2:28 PM

20 21

ELLIPTICAL OPERATION

This section explains how to use your elliptical’s console and programming.

The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:

• LOCATION OF THE ELLIPTICAL

• POWER/GROUNDING INSTRUCTIONS

• FOOT POSITIONING

• MOVING THE ELLIPTICAL

• LEVELING THE ELLIPTICAL

• POWER/MANUAL INCLINE OPERATION

• USING THE HEART RATE FUNCTION

181AXT_OM_Rev1_6.indd 20-21 7/22/11 2:28 PM

22 23

CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LED DISPLAY WINDOWS: time, distance, date and clock.

B) ALPHANUMERIC DISPLAY WINDOW: displays watts, calories, rpm, heart rate, speed and PROFILE™ display information.

C) WORKOUT PROFILE DISPLAY: displays workout level and progress.

D) PROFILE™ BUTTON: used to scroll through PROFILE™ display modes. User must be selected before pressing.

E) CHANGE DISPLAY BUTTON: used to scroll through display modes. Press to change display feedback during workout.

F) IPOD® CONTROLS: press to adjust your attached iPod® audio settings.

G) START: press to begin exercising, start your workout or resume exercising after pause.

H) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

I) IPOD®/ PROGRAMMING BUTTON: used to select program, level and time, and other options.

Used to control iPod® (during workout only).

J) INCLINE

KEYS: press to adjust incline in 5% increments.

K) RESISTANCE + / – KEYS: press to adjust resistance.

L) QUICK ADJUST KEYPAD: used to reach desired resistance or incline more quickly.

M) SET INCLINE KEY: used to change incline to level entered into keypad.

N) SET LEVEL KEY: used to change resistance to level entered into keypad.

O) AUDIO IN: plug your cd / mp3 player into the console using the included audio adaptor cable.

P) AUDIO OUT/HEADPHONE JACK: plug your headphones into this jack to listen to your music through the headphones.

Q) IPOD® DOCKING STATION: used to dock and charge your iPod® (not included).

R) SPEAKERS: music plays through speakers when your cd/mp3 player is connected to the console.

S) USB PORT: used for software updates.

BACK ENTER

ca lor ies

he art ra te

wa tts

di sta nce

ti me

cl ock

da te

per form ance fili ng sys tem

press t o switch

chang e

displ ay

sp eed

rp m

ipo d c ont rol s

S TA RT

QUI CK S TART

S TO P

HOL D TO RESE T

C

S

E

H

K

N

L

P

A

B

G

J

M

O

I

D

F

QR R

181AXT_OM_Rev1_6.indd 22-23 7/22/11 2:28 PM

24 25

cal ori e s

hea r t r at e

wat t s

di st an c e

tim e

clo ck

dat e

spe ed

r pm

DISPLAY WINDOWS

• TIME: Shown as minutes : seconds. View the time

remaining or the time elapsed in your workout.

• DISTANCE: Shown as miles. Indicates distance

traveled during your workout.

• CALORIES: Calories burned during your workout.

• HEART RATE (HR): Shown as BPM (beats per

minute). Used to monitor your heart rate (displayed

when contact is made with both pulse grips or when

wearing Polar chest strap).

• SPEED: Shown as MPH. Indicates how fast the foot

pads are moving.

• DATE/CLOCK: Displays date and time.

• WATTS: Displays current user power output.

• RPM: Rotations Per Minute.

• RESISTANCE: Shows the current level of resistance.

Will be displayed in the alphanumeric window.

• INCLINE: Shown as percent. Indicates the incline

level of the power ramp. Will be displayed in the

alphanumeric window.

• PROFILE™ DISPLAY: When PROFILE

™

is activated,

the PROFILE

™

information is displayed in the LED

windows. Use the PROFILE

™

button to change display

information. More information is on page 33.

BACK ENTER

Programming Button

GETTING STARTED

1) Check to make sure no objects are nearby that will hinder the

movement of the elliptical.

2) Plug in the power cord and turn the elliptical ON. (Switch is

located at the bottom-front of the elliptical.)

3) You have the following options to start your workout:

A) QUICK START UP

Simply press START to begin working out. Time will count up

from 0:00. The resistance level will default to level 1. Incline will

default to 0%. OR...

B) SELECT A PROGRAM

1) Select GUEST, USER 1 or USER 2 using

on the

PROGRAMMING BUTTON and press ENTER to confirm.

2) Select weight and press ENTER.

3) Select a program using

on the PROGRAMMING

BUTTON and press ENTER to confirm.

NOTE: if you press START before pressing

ENTER, the program will begin and counts

up from 0:00 for the Manual program,

and counts down from 30:00 for all other

programs. The level defaults to 1.

4) Complete the program setup using

on

the PROGRAMMING BUTTON and press

ENTER to confirm after each step.

5) When setup is complete, press START to

begin your workout.

DATE AND CLOCK SETUP

1) Enter Setup mode: Press and hold the 1

and 2 buttons for 3 seconds.

2) Use

on the PROGRAMMING

BUTTON to change settings and press

ENTER to confirm.

3) Settings include: Month, Day, Year, Hour,

Minute, and AM/PM.

4) Review settings: You can review your

settings at any time while in setup mode.

Press ENTER to scroll through settings.

5) Exit setup mode: To confirm the date

and time, press and hold ENTER for 3

seconds.

TO CLEAR SELECTION/

RESET THE CONSOLE

Hold STOP key for 3 seconds.

FINISHING YOUR WORKOUT

When your workout is complete, the display

will flash “WORKOUT COMPLETE” and

beep. Your workout information will stay

displayed on the console for 30 seconds

and then reset.

181AXT_OM_Rev1_6.indd 24-25 7/22/11 2:28 PM

26 27

PROGRAM INFORMATION

NOTE: If resistance or incline are changed during your workout, the remaining segments will be affected accordingly.

P1 MANUAL: Manually adjust your resistance and incline levels as you work out toward a time-based goal.

P2 INTERVALS: Alternating levels of resistance build endurance in this time-based workout with 16 levels to choose from.

WARM-UP PROGRAM SEGMENTS - REPEAT COOL-DOWN

TIME 4 minutes 30 60 60 30 30 60 30 60 60 30 30 60 4 minutes

LEVEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

1 1 2 2 3 5 1 1 5 5 1 5 1 1 5 5 1 3 2 2 1

2 1 2 2 3 6 2 2 6 6 2 6 2 2 6 6 2 3 2 2 1

3 1 2 2 4 7 3 3 7 7 3 7 3 3 7 7 3 4 2 2 1

4 1 2 2 5 8 4 4 8 8 4 8 4 4 8 8 4 5 2 2 1

5 2 3 5 6 9 5 5 9 9 5 9 5 5 9 9 5 6 5 3 2

6 2 3 5 7 10 6 6 10 10 6 10 6 6 10 10 6 7 5 3 2

7 2 3 5 8 11 7 7 11 11 7 11 7 7 11 11 7 8 5 3 2

8 2 3 5 9 12 8 8 12 12 8 12 8 8 12 12 8 9 5 3 2

9 3 4 5 10 13 9 9 13 13 9 13 9 9 13 13 9 10 5 4 3

10 3 4 8 11 14 10 10 14 14 10 14 10 10 14 14 10 11 8 4 3

11 3 6 10 12 15 11 11 15 15 11 15 11 11 15 15 11 12 10 6 3

12 3 6 10 13 16 12 12 16 16 12 16 12 12 16 16 12 13 10 6 3

13 5 9 13 14 17 13 13 17 17 13 17 13 13 17 17 13 14 13 9 5

14 5 9 13 15 18 14 14 18 18 14 18 14 14 18 18 14 15 13 9 5

15 5 9 13 16 19 15 15 19 19 15 19 15 15 19 19 15 16 13 9 5

16 5 9 13 17 20 16 16 20 20 16 20 16 16 20 20 16 17 13 9 5

P3 WEIGHT LOSS: Fat-burning, time-based workout that steadily builds resistance for a gradual comedown, with 16 levels to

choose from.

WARM-UP PROGRAM SEGMENTS - REPEAT COOL-DOWN

TIME 4 minutes Each segment lasts 60 seconds 4 minutes

Level 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

1 1 2 2 3 3 3 4 4 5 5 5 5 4 4 3 3 3 2 2 1

2 1 2 2 3 4 4 5 5 6 6 6 6 5 5 4 4 3 2 2 1

3 1 2 2 4 5 5 6 6 7 7 7 7 6 6 5 5 4 2 2 1

4 1 2 2 5 6 6 7 7 8 8 8 8 7 7 6 6 5 2 2 1

5 2 3 5 6 7 7 8 8 9 9 9 9 8 8 7 7 6 5 3 2

6 2 3 5 7 8 8 9 9 10 10 10 10 9 9 8 8 7 5 3 2

7 2 3 5 8 9 9 10 10 11 11 11 11 10 10 9 9 8 5 3 2

8 2 3 5 9 10 10 11 11 12 12 12 12 11 11 10 10 9 5 3 2

9 3 4 5 10 11 11 12 12 13 13 13 13 12 12 11 11 10 5 4 3

10 3 4 8 11 12 12 13 13 14 14 14 14 13 13 12 12 11 8 4 3

11 3 6 10 12 13 13 14 14 15 15 15 15 14 14 13 13 12 10 6 3

12 3 6 10 13 14 14 15 15 16 16 16 16 15 15 14 14 13 10 6 3

13 5 9 13 14 15 15 16 16 17 17 17 17 16 16 15 15 14 13 9 5

14 5 9 13 15 16 16 17 17 18 18 18 18 17 17 16 16 15 13 9 5

15 5 9 13 16 17 17 18 18 19 19 19 19 18 18 17 17 16 13 9 5

16 5 9 13 17 18 18 19 19 20 20 20 20 19 19 18 18 17 13 9 5

181AXT_OM_Rev1_6.indd 26-27 7/22/11 2:28 PM

28 29

PROGRAM INFORMATION

P4 CONSTANT WATTS: This workout automatically adjusts the resistance to keep you within a set Watts range and maintains

your desired level of exercise intensity.

1) Select Constant Watts program using and press ENTER on the PROGRAMMING BUTTON.

2) Set time using and press ENTER.

3) Select desired watts using and press ENTER.

4) Press START to being the program.

P5 MUSCLE TONER: Work toward higher resistance levels as you build strength and endurance with 10 levels to choose from.

WARM UP PROGRAM SEGMENTS - REPEAT COOL DOWN

Level 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

1 1 1 2 2 1 2 3 4 3 2 1 2 3 2 1 1 1 1

2 1 2 2 3 2 3 4 5 4 3 2 1 2 3 2 1 1 1

3 2 2 3 3 3 4 5 6 7 8 7 6 5 4 2 1 1 1

4 2 3 3 4 4 5 6 7 8 9 8 7 6 5 3 1 1 1

5 3 4 4 4 5 6 7 8 9 10 9 8 7 6 3 3 2 1

6 3 5 4 5 6 7 8 9 10 10 10 9 8 7 4 3 2 1

7 4 5 5 5 7 7 8 8 9 9 10 10 9 8 4 3 2 1

8 4 5 5 5 8 8 9 9 10 10 11 11 10 9 4 3 2 1

9 4 5 5 5 9 9 10 10 11 11 12 12 11 10 5 4 3 1

10 4 5 9 9 14 14 15 15 16 16 17 17 16 15 8 7 6 1

P6 REVERSE TRAIN: Alternate forward (F) and backward (R) pedaling at varying resistance levels for a challenging workout

that builds greater lower body and core strength, with 16 levels to choose from.

WARM-UP F R F R F R F R F R F R COOL-DOWN

TIME 4 minutes 30 60 90 60 90 45 60 45 90 90 30 30 4 minutes

LEVEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

1 1 1 1 2 3 2 3 1 2 3 1 2 3 1 2 3 2 1 1 1

2 1 1 1 2 4 3 4 2 3 4 2 3 4 2 3 4 2 1 1 1

3 1 1 1 2 5 4 5 3 4 5 3 4 5 3 4 5 2 1 1 1

4 1 1 1 3 6 5 6 4 5 6 4 5 6 4 5 6 3 1 1 1

5 1 2 3 3 7 6 7 5 6 7 5 6 7 5 6 7 3 3 2 1

6 1 2 3 4 8 7 8 6 7 8 6 7 8 6 7 8 4 3 2 1

7 1 2 3 4 9 8 9 7 8 9 7 8 9 7 8 9 4 3 2 1

8 1 2 3 5 10 9 10 8 9 10 8 9 10 8 9 10 5 3 2 1

9 1 1 1 2 11 10 11 9 10 11 9 10 11 9 10 11 2 1 1 1

10 1 1 1 2 12 11 12 10 11 12 10 11 12 10 11 12 2 1 1 1

11 2 2 2 3 13 12 13 11 12 13 11 12 13 11 12 13 2 1 1 1

12 3 3 3 4 14 13 14 12 13 14 12 13 14 12 13 14 3 1 1 1

13 3 4 4 5 15 14 15 13 14 15 13 14 15 13 14 15 3 3 2 1

14 3 4 5 6 16 15 16 14 15 16 14 15 16 14 15 16 4 3 2 1

15 3 5 6 7 17 16 17 15 16 17 15 16 17 15 16 17 4 3 2 1

16 4 6 7 8 18 17 18 16 17 18 16 17 18 16 17 18 5 3 2 1

181AXT_OM_Rev1_6.indd 28-29 7/22/11 2:28 PM

30 31

HEART RATE TRAINING

The first step in knowing the right intensity for your training is to find out your maximum heart rate (max HR = 220 – your age). The age-based

method provides an average statistical prediction of your max HR and is a good method for the majority of people, especially those new

to heart rate training. The most precise and

accurate way of determining your individual

max HR is to have it clinically tested by a

cardiologist or exercise physiologist through the

use of a maximal stress test. If you are over the

age of 40, overweight, have been sedentary for

several years, or have a history of heart disease

in your family, clinical testing is recommended.

This chart gives examples of the heart rate

range for a 30 year old exercising at 5 different

heart rate zones. For example, a 30-year-old’s

max HR is 220 – 30 = 190 bpm and 90% max

HR is 190 × 0.9 = 171 bpm.

PROGRAM INFORMATION

P7 OREGON TRAIL: Experience a hike through the foothills with an alternating resistance workout for a time-based goal.

Choose from 10 levels.

WARM-UP PROGRAM SEGMENTS - REPEAT COOL-DOWN

TIME 4 minutes 30 90 90 30 30 90 30 90 90 30 30 90 4 minutes

LEVEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

1 1 1 1 1 3 1 1 3 3 1 3 1 1 3 3 1 1 1 1 1

2 1 1 1 2 3 1 1 3 3 1 3 1 1 3 3 1 2 1 1 1

3 1 1 1 2 4 2 2 4 4 2 4 2 2 4 4 2 2 1 1 1

4 1 1 1 3 4 2 2 4 4 2 4 2 2 4 4 2 3 1 1 1

5 1 2 3 3 5 3 3 5 5 3 5 3 3 5 5 3 3 3 2 1

6 1 2 3 4 5 3 3 5 5 3 5 3 3 5 5 3 4 3 2 1

7 1 2 3 4 6 4 4 6 6 4 6 4 4 6 6 4 4 3 2 1

8 1 2 3 5 6 4 4 6 6 4 6 4 4 6 6 4 5 3 2 1

9 2 2 3 5 7 5 5 7 7 5 7 5 5 7 7 5 5 3 2 2

10 2 2 4 6 7 5 5 7 7 5 7 5 5 7 7 5 6 4 2 2

P8 THR ZONE: Simulate the intensity of your favorite sport as the program resistance automatically adjusts to maintain a set

Target Heart Rate range.

1) Select THR Zone program using

and press ENTER on the PROGRAMMING BUTTON.

2) Select TIME using

and press ENTER on the PROGRAMMING BUTTON.

3) The HEART RATE window will flash showing the default target heart rate of 80 beats per minute. Select your target heart

rate (from heart rate training chart) using

on the PROGRAMMING BUTTON and press ENTER.

4) Press START to begin.

P9 HR INTERVALS: Automatically adjusts peak and valley resistance levels within your desired heart rate. Perfect for providing

an intense workout with recovery bursts. Time-based goal.

1) Set TOTAL WORKOUT TIME using

on the PROGRAMMING BUTTON or the KEYPAD and press ENTER.

2) Set PEAK interval target heart rate using

or the KEYPAD and press ENTER.

3) Set PEAK interval time using

or the KEYPAD and press ENTER.

4) Set VALLEY interval target heart rate using

or the KEYPAD and press ENTER.

5) Set VALLEY interval time using

or the KEYPAD and press ENTER. Press START to begin.

WARM UP WORK INTERVAL REST INTERVAL COOL DOWN

TIME 4:00

min

The peak interval and valley interval segment times are preset

by the user and are repeated until the cool down.

2:00

min

2:00

min

RESISTANCE

0%

Or user selects

THR set by user for the peak and valley intervals.

50%

Current Resistance

0%

NOTES:

• The large LED dot matrix window displays your heart rate during exercise. The middle row represents your target heart rate (THR)

and the other rows equal +/-2 heart beats. If you are working out beneath your THR, the LEDs below the middle row will illuminate.

If you are over, the LEDs above the middle row will illuminate. Your current heart rate is represented by the flashing column and the

window will refresh every 5 seconds.

• There is a 4-minute warm-up built into this program at level 1 resistance.

• After 4 minutes, the resistance will automatically adjust to bring your heart rate within 5 beats of the target number you selected at

the beginning of the program.

• If there is no heart rate detected, the unit will not change resistance levels up or down.

• If your heart rate is 25 beats over your target zone the program will shut down.

Target Heart

Rate Zone

Workout

Duration

Example THR

Zone (age 30)

Your

THR Zone

Recommended For

VERY HARD

90

– 100%

< 5

min

171 – 190

bpm

Fit persons and for athletic training

HARD

80

– 90%

2

– 10

min

152 – 171

bpm

Shorter workouts

MODERATE

70

– 80%

10

– 40

min

133 – 152

bpm

Moderately long workouts

LIGHT

60

– 70%

40

– 80

min

114 – 133

bpm

Longer and frequently repeated

shorter exercises

VERY LIGHT

50

– 60%

20

– 40

min

104 – 114

bpm

Weight management and active

recovery

181AXT_OM_Rev1_6.indd 30-31 7/22/11 2:28 PM

32 33

PROGRAM INFORMATION

P10 CARDIO BOOST: Take your fitness goals to the next level with high-energy bursts that alternate resistance and incline

combinations for greater results in less time. Choose from 10 levels.

NOTE: All elevations are listed as a percent of total elevation.

WARM UP PROGRAM SEGMENTS - REPEAT COOL DOWN

TIME 4:00

min

1:30 :30 1:30 :30 1:30 30 1:30 :30 4:00

min

LEVEL Segment # 1 2 3 4 5 6 7 8 9 10 11 12

1

Incline 5 10 5 15 5 15 5 30 5 30 10 5

Resistance 1 2 1 3 1 3 1 6 1 6 2 1

2

Incline 5 15 10 25 10 25 10 35 10 35 10 5

Resistance 1 3 2 5 2 5 2 7 2 7 2 1

3

Incline 10 15 15 35 15 35 15 40 15 40 15 10

Resistance 2 3 3 7 3 7 3 8 3 8 3 2

4

Incline 10 20 20 45 20 45 25 5 25 5 15 10

Resistance 2 4 4 9 4 9 5 10 5 10 3 2

5

Incline 15 15 30 55 30 55 35 60 35 60 25 15

Resistance 3 3 6 11 6 11 7 12 7 12 5 3

6

Incline 15 20 40 65 40 65 45 70 45 70 25 15

Resistance 3 4 8 13 8 13 9 14 9 14 5 3

7

Incline 20 20 45 70 45 70 50 75 50 75 25 15

Resistance 4 4 9 14 9 14 10 15 10 15 5 3

8

Incline 20 25 5 75 50 75 55 80 55 80 25 15

Resistance 4 5 10 15 10 15 11 16 11 16 5 3

9

Incline 20 25 60 80 60 80 65 85 65 85 25 15

Resistance 4 5 12 16 12 16 13 17 13 17 5 3

10

Incline 20 25 70 90 70 90 75 90 75 90 25 15

Resistance 4 5 14 18 14 18 15 18 15 18 5 3

P11 MOUNTAIN CLIMB: Combinations of resistance and incline gradually increase for an effective, climb-simulated workout that

boosts strength and endurance, with 10 levels to choose from.

NOTE: All elevations are listed as a percent of total elevation.

WARM UP PROGRAM SEGMENTS - REPEAT COOL DOWN

TIME 4:00

min

1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 1:00 4:00

min

LEVEL Segment # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1

Incline 5 10 15 15 15 10 10 10 10 10 10 15 15 15 5 5

Resistance 1 2 4 4 5 5 6 6 6 6 5 5 4 4 3 2

2

Incline 5 15 20 20 20 15 15 15 15 15 15 20 20 20 10 10

Resistance 1 3 6 6 7 7 8 8 8 8 7 7 6 6 3 2

3

Incline 10 15 30 30 30 25 25 25 25 25 25 30 30 30 15 15

Resistance 2 3 7 7 9 9 10 10 10 10 9 9 7 7 3 2

4

Incline 10 20 40 40 40 35 35 35 35 35 35 40 40 40 20 20

Resistance 2 4 8 8 10 10 11 12 12 11 10 10 8 8 3 2

5

Incline 15 15 50 50 50 45 45 45 45 45 45 50 50 50 25 25

Resistance 3 3 9 9 11 11 12 13 13 12 11 11 9 9 4 3

6

Incline 15 20 60 60 60 55 55 55 55 55 55 60 60 60 30 30

Resistance 3 4 10 10 12 12 13 14 14 13 12 12 10 10 4 3

7

Incline 20 20 70 70 70 65 65 65 65 65 65 70 70 70 35 35

Resistance 4 4 11 11 13 13 14 15 15 14 13 13 11 11 5 4

8

Incline 20 25 80 80 80 75 75 75 75 75 75 80 80 80 40 40

Resistance 4 5 12 12 14 14 15 16 16 15 14 14 12 12 5 4

9

Incline 20 25 90 90 90 85 85 85 85 85 85 90 90 90 40 40

Resistance 4 5 13 13 15 15 16 17 17 16 15 15 13 13 5 4

10

Incline 20 25 100 100 100 90 90 90 90 90 90 100 100 100 40 40

Resistance 4 5 14 14 16 16 17 18 18 17 16 16 14 14 5 4

181AXT_OM_Rev1_6.indd 32-33 7/22/11 2:28 PM

34 35

CUSTOM PROGRAMS

1) Select CUSTOM 1, 2 or 3 program using and press ENTER on the

PROGRAMMING BUTTON.

2) Set time using

and press ENTER on the PROGRAMMING BUTTON.

3) Set the RESISTANCE profiles using

and press ENTER on the PROGRAMMING

BUTTON after each segment is set to the desired level (repeat until all 15 segments are

set).

4) Next, set the INCLINE profiles using

and press ENTER on the PROGRAMMING

BUTTON after each segment is set to the desired level (repeat until all 15 segments are

set). NOTE: if BACK is pressed on the PROGRAMMING BUTTON, it will take you back to

previous segment.

5) Press START to begin the program.

NOTE: to reset the memory, press and hold ENTER for 5 seconds.

BACK ENTER

Programming Button

ACCUMULATED DATA

Once PROFILE

™

is activated, you can scroll through your accumulated data in multiple formats by pressing the PROFILE

™

button. A

workout is saved when: the program ends, the console is paused and not resumed within 5 minutes, or the STOP button is held to

reset the console.

1) LAST WORKOUT: This option allows you to view your accumulated data from your last workout. The current workout becomes

the last workout once a program has ended or the console has been reset. The following information will be shown in each

display window:

• TIME - Total time of last workout.

• DISTANCE - Total distance of last workout.

• WATTS - Average watts of last workout.

• RPM - Average RPM of last workout.

• CALORIES - Total calories burned of last workout.

• SPEED - Average speed of last workout.

PROFILE

™

PERFORMANCE TRACKER

Research shows that those who journal their fitness routines or workouts, on average, achieve greater success than those who do

not. Because your new elliptical is equipped with AFG’s exclusive PROFILE

™

Performance Tracker, you’ve taken an important step

towards achieving your fitness goals.

The integrated PROFILE

™

software allows you to track your fitness progress over time without the need for paper journals or logs.

With PROFILE

™

, you can easily compare your current workout to your last, average or lifetime workout totals. With quick access to

feedback like duration of workout or calories burned during previous workouts, you’ll be able to see the progress you’ve made. Read

further to learn about how PROFILE

™

can help motivate you to enhance your performance.

SETUP

To activate PROFILE

™

, a user MUST be chosen before the program

begins. To select a USER 1 or 2, use the PROGRAMMING BUTTON

and press ENTER to confirm. All accumulated data specifically relates

to the user that is chosen. NOTE: If no user is selected and clock and

date are not set, no data will be tracked.

RESET

Reset all recorded information for USER 1 or USER

2 by selecting the user and then holding down the

PROFILE

™

button for 10 seconds. Note: This step is

permanent and will delete ALL previously accumulated

data for the chosen user.

181AXT_OM_Rev1_6.indd 34-35 7/22/11 2:28 PM

36 37

PROFILE

™

PERFORMANCE TRACKER

ACCUMULATED DATA

2) AVERAGE WORKOUT: This option allows you to see your average accumulated data for the last 30 workouts. The following

information will be shown in each display window:

• TIME - Average workout time.

• DISTANCE - Average workout distance.

• WATTS - Average watts of workout.

• RPM - Average RPM.

• CALORIES - Average calories burned.

• SPEED - Average speed of workout.

3) WEEKLY GOAL: Indicates the weekly goal you set. “LEFT” – Indicates the time or distance you have left to complete to meet your

weekly goal. TIME or DISTANCE – The total time or distance goal you selected and the time or distance you have left to complete to

meet your weekly goal.

• The “GOAL” and “LEFT” will display alternately every 3 seconds.

• A “GOAL DONE” message will appear when goal is completed.

• If the date and clock are not set and/or a weekly goal is not set, weekly goal will display zeros.

• The time or distance left for the weekly goal will reset at the end of each week.

4) WEEKLY TOTAL: View your accumulated data from the last Sunday to the present day. NOTE: This data is based on week to date

NOT the previous seven days. For instance, if you have not used the machine since Sunday, the console will read zeros. The following

information will be shown in each display window:

• TIME - Total time of workout.

• DISTANCE - Total distance of workout.

• WATTS - Average watts of weekly workout.

• RPM - Average RPM of weekly workout.

• CALORIES - Average calories burned.

• SPEED - Average speed of weekly workout.

NOTE: If the date and clock are not set, weekly total will default to the last workout data.

5) LIFETIME TOTAL: This option allows you to view the total accumulated data. The following information will be shown in each display

window:

• TIME - Total accumulated time. NOTE: If time is greater than 59:59, the time will no longer display minutes and will display hours only.

• DISTANCE - Total accumulated distance.

• WATTS - Average watts.

• RPM - Average RPM.

• CALORIES - Average calories burned.

• SPEED - Average speed.

PROFILE

™

PERFORMANCE TRACKER

WEEKLY GOAL SETUP

1) Select USER 1 or USER 2.

2) Press

PROFILE

™

button until it displays “WEEKLY GOAL.” Press ENTER.

3) Use

to set a time goal (leave time at 0:00 if you want to set a distance goal). Press ENTER.

4) Use

to set a distance goal. If the distance is changed from 0.00, distance will be the goal.

NOTE: you may only set a time or distance goal, not both.

5) Press ENTER to exit the weekly goal setup mode.

USING YOUR CD / MP3 PLAYER

1) Connect the included AUDIO ADAPTOR CABLE to the AUDIO IN JACK on the left of the

console and the headphone jack on your CD / MP3 player.

2) Use your CD / MP3 player buttons to adjust song settings.

3) Remove the AUDIO ADAPTOR CABLE when not in use.

4) If you don’t want to use the SPEAKERS, you can plug your headphones into the AUDIO

OUT JACK at the bottom of the console.

DOWNLOADING A SOFTWARE UPDATE FROM AFGFITNESS.COM

Occasionally a software update may be available for your console, via the included USB port.

Please visit http://www.afgfitness.com/customer-support/software-update/ to see if an update is available and get

detailed instructions on how to download the latest software from your PC or Mac.

NOTE: Performing a software update will delete all previously saved workout information.

181AXT_OM_Rev1_6.indd 36-37 7/22/11 2:28 PM

38 39

BACK ENTER

IPOD

®

DOCKING

STATION

RUBBER

PLUG

AUDIO IN

JACK FOR

NON-IPOD

PLAYERS

IPOD

®

CONTROLS

AUDIO

OUT JACK

IPOD

®

DOCKING STATION

The iPod docking station is the entertainment solution for your

workouts. Various iPod and iPhone models with a dock connector can

fit this dock.

USING THE IPOD DOCKING STATION

(IPOD NOT INCLUDED)

1) Remove the rubber plug from bottom of the docking station.

2) Plug in your iPod/iPhone by matching the dock connector

pin on the console with the dock connector on your iPod/

iPhone. NOTE: Once you have connected the device to the

docking station, please allow 10 seconds for docking station to

authenticate before it will be fully functional.

3) Use the controls below the dock to adjust volume and music

selection. Use the programming button to access full iPod

functionality. NOTE: If you don’t want to use the speakers, you

can plug your headphones into the audio out jack at the bottom

of the console.

Replace the rubber plug into the bottom of the docking station when

the station is not in use or for use with other media players.

NOTE: Audio will not play through speakers if audio adaptor cable is

plugged in while iPod/iPhone is in the docking station.

BACK ENTER

READY

Connect your Nike Plus-compatible device to the built-in

Made for iPod connector on Nike + iPod compatible

fitness equipment.

SET

Full console controls and built-in SonicSurround

™

speakers make it easy to exercise to your favorite

workout playlist.

GO

Start walking or running. Your distance, time, and

calories burned are recorded as you go. It’s all

automatically saved on your iPod or iPhone.

SYNC

When you’re done with your workout, connect your iPod

or iPhone to your computer. iTunes syncs your workout

data to nikeplus.com. Every workout and every run is

there, ready for you to review.

“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by

the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance

with safety and regulatory standards. iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

181AXT_OM_Rev1_6.indd 38-39 7/22/11 2:28 PM

La page est en cours de chargement...

AFG 18.1AXT Le manuel du propriétaire

AFG 18.1AXT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents