Sanyo HT27744 Le manuel du propriétaire

AS

Printed in U.S.A. SMC, May 2004

Impreso en U.S.A. SMC, Mayo 2004

Imprimé aux É.-U. SMC, mai 2004

Part No. / No. de Parte/

N

o

de pièce : 1AA6P1P4417A–

Service Code/Código de Servicio/

Code de service : 610 312 2304

Importado Por :

Comercializadora México

Americana, S. DE R.L. DE C.V.

Nextengo Nº 78

Col. Santa Cruz Acayucan

Del. Azcapotzalco, México D.F. C.P.

02770, RFC CMA 9109119L0

Telefono: 55-5328-3500

ENERGY STAR

“As an ENERGY STAR

®

Partner, Sanyo

Manufacturing Corporation has determined

that this product meets the ENERGY STAR

®

guidelines for energy efficiency.”

Model Nos.:

No. de Modelo:

N

o

de modele:

HT27744

HT30744

HT32744

“Read this manual before assembling (or using) this product.”

Need assistance?

Visit our Web site at www.sanyoctv.com or

Call toll free 1-800-877-5032

Ownerʼs Manual

ENGLISH

Table of Contents . . . . . . . 3

Manual de Instrucciónes

ESPAÑOL

Contenido . . . . . . . . . . . . 25

Manuel dʼinstructions

FRANÇAIS

Table des matières . . . . . 48

AS

HT30744

HT32744

HT27744

As Real

As It Gets!

2

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE,

ANSI/NFPA 70

Positioning the appliance

1. Do not place your appliance on an unstable cart, stand, shelf or table.

Serious injury to an individual, and damage to the appliance, may result if

it should fall. Your salesperson can recommend approved carts and stands

or shelf and wall mounting instructions. An appliance and cart combination

should be moved with care. Quick stops, excessive force, and uneven surfaces may

cause the appliance and cart combination to overturn.

2. Slots and openings in the cabinet and in the back or bottom are provided for ventilation.

To ensure reliable operation of the appliance and to protect it from overheating, these

openings must not be blocked or covered. The openings should never be covered with

a cloth or other material, and the bottom openings should not be blocked by placing the

unit on a bed, sofa, rug, or other similar surface. This appliance should never be placed

near or over a radiator or heat register. This appliance should not be placed in a built-in

installation such as a bookcase unless proper ventilation is provided.

3. Do not expose the appliance to rain or use near water . . . for example, near a bathtub,

swimming pool, kitchen sink, in a wet basement, etc.

Hooking Up Outdoor Antenna

LIGHTNING PROTECTION FOR YOUR ANTENNA AND SET AS PER NATIONAL ELECTRICAL CODE

I

NSTRUCTIONS.

4. If an outside antenna is connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage surges and built up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides informa-

tion with respect to proper grounding of the mast and supporting structure, grounding

of the lead in wire to an antenna discharge unit, size of grounding conductors, location

of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

An outside antenna system should not be located in the vicinity of overhead power

lines or other electric light or power circuits, or where it can fall into such power lines

or circuits. When installing an outside antenna system extreme care should be taken to

keep from touching such power lines or circuits as contact with them might be fatal.

Plug in the power cord

5. This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply to your home, consult

your product dealer or local power company. This product is equipped with a polarized

alternating current line plug (a plug having one blade wider than the other). This plug

will fit into the power outlet only one way. This is a safety feature. If you are unable

to insert the plug fully into the outlet, try reversing the plug. If the plug should still

fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of this polarized plug. Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of fire or electric shock.

6. Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where they exit from the product.

Cleaning

7. Before cleaning, unplug the unit from the wall outlet. Do not apply liquid cleaners or

aerosol cleaners directly to the unit. Use a dry cloth for cleaning.

Service & Repair

8. Unplug the appliance from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

A. If the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the appliance.

C. If the appliance has been exposed to rain or water.

D. If the appliance has been dropped or the cabinet has been damaged.

E. If the appliance exhibits a distinct change in performance.

F. If the appliance does not operate normally by following the operating

instructions, adjust only those controls that are covered in the operating

instructions. Improper adjustment of other controls may result in damage

and will often require extensive work by a qualified technician to restore the

appliance to normal operation.

9. Upon completion of any service or repair, request the service technician’s assurance

that only Factory Authorized Replacement Parts that have the same characteristics as

the original parts were used, and that routine safety checks have been performed to

determine that the appliance is in safe operating condition. Unauthorized substitutions

may result in fire, electrical shock, or other hazards.

10. Never add accessories that have not been specifically designed for use with this appli-

ance as they may cause hazards.

11. For added protection during a lightning storm, or when the set is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the

antenna. This will prevent damage to the set due to lightning or power line surges.

12. Never push objects of any kind into this product through openings as they may touch

dangerous voltage points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELEC-

TRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE ADHERE TO ALL WARNINGS ON THE PRODUCT AND IN THE OPERATING INSTRUCTIONS. BEFORE OPERATING THE PRODUCT, PLEASE

READ ALL OF THE SAFETY AND OPERATING INSTRUCTIONS. RETAIN THIS LITERATURE FOR REFERENCE. Follow all instructions...

“Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.”

2 Important Safety Information

Positioning the TV

Do not position the TV in a confined area. Allow space for normal air circulation

around electronic parts.

Child Safety

Sanyo is committed to making home entertainment safe and enjoyable. Always use

an appropriate table or stand when positioning your TV. Use appropriate brackets,

braces, or straps to anchor your furniture in place. But never screw anything

directly to the television.

Do not place televisions on dressers, shelves, desks, carts, etc., where curious

or excited children could pull, push, or otherwise cause the unit to fall and cause

personal injury.

Never place toys or other items on top

of the TV that could pique children’s

curiosity causing them to climb

about the furniture.

Always use stands that are designed

to support the size and combined

weight of your television and other

electronic devices.

AS

VIDEO IN L-AUDIO-R

NEC - NATIONAL ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

Welcome to the World of Sanyo

Thank you for purchasing this Sanyo High-Definition Digital Television. You made an excellent choice for Performance, Reliability,

Features, Value, and Styling.

To The Owner

We are aware that you are eager to begin using your new HDTV. However, we also understand that to enjoy it fully you must first understand its

many features. While this owner’s manual is intended to fully acquaint you with the TV’s operation, it is not meant to be read from cover to cover.

Instead, it has been carefully arranged for easy use so you can find what you need, then move on quickly to enjoying your digital television.

Table of Contents / Introduction 3

Introduction

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 2

Welcome to the World of Sanyo . . . . . . . . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HDTV Back—Jacks Locations & Functions . . . . . . . . . . . . 6

Signal Connections

Analog (RF) Antenna Connection . . . . . . . . . . . . . . . . . . . . 7

Digital (DTV) Antenna Connection . . . . . . . . . . . . . . . . . . . 7

Setting Up the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Digital A/V Connections

Connecting External Equipment to HDMI Input

with HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting STB or DVD with DVI Output to HDMI Input

With HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using the Component jacks to connect a DVD Player or

Other digital equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Analog A/V Connections

Using the S-Video Jacks to connect a VCR or DVD

Player to A/V jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Audio Connections

Connecting Digital Audio Output to a Stereo Amplifier . . 10

Connecting Analog Audio Output to a Stereo Amplifier . . 10

Typical Home Theater Connections . . . . . . . . . . . . . . . . . . . 11

Using the Multimedia Remote Control

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Programming the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Remote Program Codes (VCR/DVD/Satellite/Cable) . . 14~15

Remote Program Key Functions Chart . . . . . . . . . . . . . . . . 15

TV Adjustment and Setup

How to Operate the On-Screen Menu . . . . . . . . . . . . . . . . 16

Menu Navigation Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Digital Cable Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Digital Add-On Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Antenna Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Initial Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Closed-Captioning

How to View Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

How to Customize Digital Captioning On-Screen Display . . . 18

V-Guide (Parental Control) Operation

How to Block Movies or TV Programs . . . . . . . . . . . . . . . 19

How to Temporarily Unblock Movies or TV Programs . . . 19

How to Unblock Movies or TV Programs . . . . . . . . . . . . . 19

Setup Menu

Setting the Clock Manually . . . . . . . . . . . . . . . . . . . . . . . . 20

Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TV Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Picture/Sound Adjustment

Adjusting the Picture/Sound Manually . . . . . . . . . . . . . . . . 20

Color Enhancer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Scan Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PAP (Picture and Picture)

Using the PAP Split Screen . . . . . . . . . . . . . . . . . . . . . . . . 21

Switching Between the Split Windows . . . . . . . . . . . . . . . 21

Freezing the PAP Window . . . . . . . . . . . . . . . . . . . . . . . . . 21

Operating PAP Screens with other features . . . . . . . . . . . . 21

Helpful Hints (Problems/Solutions) . . . . . . . . . . . . . . . . . . 22

Warranty (Mexico) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warranty (U.S.A. and Canada) . . . . . . . . . . . . . . . . . . . . . . 24

Contents

 27″ High-Definition Digital True Flat-screen television



30″ High-Definition Digital True Flat Wide-screen television



32″ High-Definition Digital True Flat-screen television

 Trilingual Menu Options

 Built-in Digital and Analog Tuners

 Automatic Channel Search



Auto Shut Off



3-D Digital Comb Filter (for better picture detail)

 Adjustable Scan Velocity Modulation



V-Chip for Movies and TV guidelines rating limits (parental

control)

 Closed-Captioning: Analog EIA-608B and Digital (EIA-708B)

 Audio Modes: DTV—Main and Sub

NTSC—Stereo, Mono, and SAP

 Front Surround Sound

 Bass / Treble

 Front speakers 6 x 12 cm (two)

 Factory preset adjustments for picture/sound

 Picture shape: Letter box, Zoom, Normal, and Full (HT30744 only)

 Initial Channel (automatic selection)

 Receivable Formats: Two tuning system: with integrated ATSC

digital tuner for terrestrial and nonscrambled (ClearQAM)

cable channels. NTSC analog tuner for VHF/UHF or CATV

 Audio Format: Dolby Digital for DTV and Analog for NTSC



PAP (Picture-and-Picture) split-screen

 Channel Scan Memory



Color Enhancer

 Auto Flesh Tone

 Receives 181 Analog Channels [VHF 2~13 and UHF 14~69;

Cable TV 1, 14~125]; and 99 Digital Channels

 RF Antenna Input Jacks: Digital and Analog

 HDMI (High-Definition Multimedia Interface) Input with

HDCP (High-bandwidth Digital Content Protection)

 Component Video Input (Two Sets)

 Rear AV Input (Two Sets)

 S-Video Input (Two Sets)

 Optical Digital Audio Out

 Audio Out (Switchable)



Clock (auto clock)

 XDS (Extended Data Services) displays station call letters,

Title of show, and ratings when broadcast

 Sleep Timer (3 hours)

 52-Key DTV Multimedia Remote Control

4 Features & Specifications

Picture Tube Size (Measured Diagonally):

HT27744 - 27″; HT30744 - 30″; HT32744 - 32″ True Flat screens

Picture Resolution: RF: Input–330, AV Input–800

Scanning Format: 1080i

RF Antenna Input: Analog–UHF/VHF/CATV 75 ohm

Digital–75 ohm

No Signal Reception: TV automatically switches off after 15 minutes

In Video Modes, TV will NOT switch off

Power Requirement: Source: AC 120V, 60Hz

Power Consumption: 140 Watts

Sound: Two Speakers, size: 6x12cm

Amplifier: Built-in with 5.0W/ch

Jacks and Connectors:

Video 1 Input: S-Video1, Video and Audio L/R

Video 2 Input: S-Video2, Video and Audio L/R

Compo 2 Input: Component (Y/Pb/Pr), with shared

Video 2 Audio L/R input

Compo 3 Input: Component (Y/Pb/Pr), and

Audio 3 L/R input

Digital Audio Output: S/P DIF or PCM

Analog Audio Output: Audio L/R

HDMI Input: 19-pin connector (Picture/Sound)

Service input Terminal: For Technical use only

CAUTION: FCC Regulations state that improper modifications or unauthorized

changes to this unit may void the user’s authority to operate the unit.

This symbol on the nameplate means the product is Listed by

Underwriters’ Laboratories Inc. It is designed and manufactured to

meet rigid U.L. safety standards against risk of fire, casualty and

electrical hazards.

Trademarks Information:

Manufactured under license from Dolby Laboratories. “Dolby”

and the double-D symbol are trademarks of Dolby Laboratories.

Size and Weight (approximately):

HT27744

Horizontal Dim. (Width): 30.3 in. (770mm)

Vertical Dim. (Height): 23.0 in. (585mm)

Depth Dim. (Thickness): 19.5 in. (496mm)

Weight: 103.5 (lbs.), 47.0 (Kg)

HT30744

Horizontal Dim. (Width): 35.7 in. (908mm)

Vertical Dim. (Height): 22.5 in. (572mm)

Depth Dim. (Thickness): 21.8 in. (553mm)

Weight: 132.2 (lbs.), 60.0 (Kg)

HT32744

Horizontal Dim. (Width): 35.0 in. (888mm)

Vertical Dim. (Height): 27.0 in. (687mm)

Depth Dim. (Thickness): 22.4 in. (570mm)

Weight: 143.4 (lbs.), 65.1 (Kg)

Features Specifications

Analog—Commonly refers to the current NTSC transmission

standard for televisions.

Aspect Ratio—This term describes the ratio of the width to the

height of a TV screen independent of the screen size (x units wide

by x units high).

ATSC—Advanced Television Systems Committee (digital standards

committee).

Bandwidth—The range of frequencies assigned to a broadcast

channel. A TV channel is 6 MHz wide.

ClearQAM Digital Channels—Unscrambled digital cable chan-

nels. Cable companies may or may not choose to provide ClearQAM

channels.

Dolby® Digital (Formally known as Dolby AC-3)—A 5.1 channel

(Front L/R, Rear L/R, Center, and Bass) surround sound audio

standard for digital television.

Downconverting—A process for decreasing the number of pixels

in an image. Frame rate and/or scanning format may also change.

Broadcasters may use this process to make room in their bandwidth

for additional services.

DTV (Digital Television)—Comprises three elements, HDTV,

EDTV, and SDTV.

DVI (Digital Video Interface)—Designed to accommodate

both analog and uncompressed digital video signals with a single

connector.

EDTV—Enhanced Definition Television (480p).

HDCP—High-bandwidth Digital Content Protection. A means of

protecting copyrighted digital entertainment content.

HDMI—High Definition Multimedia Interface. HDMI is a new stan-

dard digital connection between A/V devices, such as a set-top box,

DVD player or A/V receiver, and a digital television. HDMI offers

exceptional video and audio quality with a single quick-disconnect

connector. HDMI supports multi-channel digital audio transmissions

and component video color spacing for true rendering of high-

definition video. It supports the HDCP protection standard, allowing

transmission of copy-protected digital content to your display.

HDTV—High Definition Television (1080i & 720p).

Interlaced Scanning—The process of scanning two fields of video

then combining (interlacing) them to make one frame.

Letter Box—A widescreen 16:9 aspect ratio image

being displayed on a 4:3 aspect ratio screen. Black

borders appear at the top and bottom of the screen

(image fails to fill screen vertically).

Multicasting—The dividing of a station’s broadcast signal into sub-

channels of programming or data services.

NTSC—National Television Systems Committee (analog standards

committee).

OSD—On Screen Display.

Pulse Code Modulation (PCM)—This is a binary digital signal

format used for digitizing analog data.

Pillar Box—A 4:3 aspect ratio image being

displayed on a 16:9 ratio screen. Black borders

appear at the sides of the screen (image fails to fill

screen horizontally).

Postage Stamp—This term is used to describe a 4:3

aspect ratio image that the broadcaster has up-coverted

to a 16:9 aspect ratio image, then displayed on a 4:3

aspect ratio screen. Black borders appear at the top,

sides, and bottom of the screen (image fails to fill screen both verti-

cally and horizontally). (See Zoom definition below.)

Progressive Scanning—The process of scanning lines sequentially.

One field produces one frame.

PSIP—Program and System Information Protocol is a collection of

tables designed to operate within every transport stream for DTV

broadcasts. PSIP includes instructions advising TVs that a change

is about to occur and where virtual channel programming can be

found.

Set-Top Box (STB)—A device that receives and converts signals for

display on a television screen or monitor (can be digital or analog).

Many digital STBs have cable and off-air tuners.

SDTV—Standard Definition Television (480i).

Simulcast—A broadcast station simultaneously broadcasting the

same program on an analog channel and a DTV channel. This is

required by the FCC during the transition from analog to digital.

Spectrum—A continuous band of frequencies.

S/P DIF —S/P DIF is a digital audio format that can transmit a Dolby

Digital bit stream. By connecting this output to an AV receiver that

includes a Dolby Digital decoder, the TV can reproduce up to 5.1

channels of surround sound. S/P DIF can also transmit PCM audio.

Surround Sound (Front)—This feature adds another dimension to

the acoustic experience and helps to improve the movie-theater like

sound.

Terrestrial Broadcast—An over-the-air broadcast to an antenna.

Tuner Indicator—The letters “D,” “C,” or “DC” will appear directly

to the left of the channel number:

Off-air channels selected with the digital (DTV) tuner will have

the prefix “D.”

Channels selected with the analog (NTSC) tuner will either have

the prefix “C” (analog cable channels) or will be blank (for terres-

trial, VHF/UHF channels).

ClearQAM digital cable channels will have the prefix “DC.”

Tuner Key—This key is used to toggle from one tuning system to

another, digital channels and analog channels.

Upconverting—A process for increasing the number of pixels in an

image (may include changing the frame rate and scanning format).

Additional pixels are inserted between existing pixels in an attempt to

simulate HDTV. This process does not increase the resolution.

Virtual Channel—Channels broadcasted with major and minor

information contained in the PSIP package. The number of virtual

channels a broadcaster can send depends on the resolution of the

programming.

Wide-Screen—Used to describe a 16:9 or greater aspect ratio. 16:9

is the standard aspect ratio for HDTV programming. Movies screens

are sometimes slightly wider (often 2:1).

Zoom—Enlarges center of the image. For

instance, if you have a postage stamp image

shape, press this key to enlarge image.

Glossary

Glossary 5

6 Getting Started / Back Panel Jacks

This new high-definition digital television is capable of reproducing a crystal clear picture and exceptional sound.

Just like being There!

To get the best performance from this HDTV you will need to...

1. Choose the appropriate Signal Connection, “The Signal Makes the Difference,” pages 7

2. Connect External equipment, if desired, pages 8 ~ 11

3. Install Batteries in the Remote, and Review the functions, pages 12~13

4. Program Remote to operate other equipment, if desired, pages 13~15

5. Follow the on-screen menu display to customize and setup features, pages 16~21

Note: For additional assistance, reference the Quik ’N Easy Setup guide to learn how different signals and external equipment

effect picture quality. Follow the examples there to ensure that you are getting the best possible picture, based on your

external equipment’s capability and your signal quality.

Getting Started



Component Video Input (COMPO 2)—Connect digital video

equipment to the Y, Pb, Pr and VIDEO 2 Audio L/R jacks.

These jacks will automatically detect the type of signal being

received (HDTV, EDTV, or SDTV).



S-Video (Video 1 and 2) Input—To enhance video detail use

the S-Video (Video 1/2) jacks instead of the Video jacks, if

available on your external equipment. (S-Video connections

will override connections to the Video 1/2 input jacks.)



Digital Audio Output—Optical connection for advanced

Dolby™ Digital 5.1 stereo home theater systems.



HDMI (High Definition Multimedia Interface) Input—

Connect digital video equipment to this jack. It only takes one

high bandwidth cable (not supplied) to communicate between

the video/audio equipment and this TV. This connection is com-

patible with DVI equipped devices. (Separate audio connection

is required for DVI device.)



Analog Audio Out (L/R) Jacks—Connect external audio

equipment here. (See page 10.)



Component Video Input (COMPO 3)—Connect digital video

equipment to the Y, Pb, Pr and AUDIO 3 (L/R) jacks. (See

page 9.) These jacks will automatically detect the type of signal

being received (HDTV, EDTV or SDTV).



Audio/Video Input (AV1/AV2)—Connect standard video

equipment here (see page 9).

Note: S-Video1/2 connections override the AV1/2 video

composite connections.



Analog Antenna Input (UHF/VHF/CATV)—Connect an RF

antenna, cable, or satellite receiver to this jack as shown on

page 7.



Digital Antenna Input—Connect an RF antenna to this jack as

shown on page 7.



Service Terminal—For technical use only.

ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

















HDTV Back—Jacks Locations and Functions

Signal Connection : Digital/Analog / Setting Up the TV 7

Digital (DTV) Antenna Connection

Connect RF antenna to the splitter, then to

the TV Digital Antenna In Terminal.

QuickTips

■

The TV will auto-

matically select an

Antenna mode for the

type of Analog RF

signal you connect.

Use “Antenna Selec-

tion” in the Setup

menu to change

Antenna mode.

■

TV will switch off

automatically after

15 minutes if there is

no signal reception

(cable out or station

not broadcasting).

Exception—When a Video

mode is selected, the

TV will not automati-

cally switch off when

signal reception

has stopped for 15

minutes.

■

If you move the TV to

a new location, press

the RESET key twice

after connecting the

signal and turning on

the TV.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

To connect a High-Definition cable or satellite set-top box, go to page 8.

Analog RF Antenna Connection

Connecting Analog Cable service, RF antenna,

or Satellite Receiver to the TV Analog

(UHF/VHF/CATV) 75 ohm terminal.

TV BACK

RF ANTENNA

ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

IN FROM

SAT.

CATV IN

OUT TO TV

S-VIDEO

CH3

CH4

L- -RAUDIOVIDEO

FROM ANT.

OUT TO TV

IN

OUT

Note: If you do not

have a VCR connect

signal directly to the TV

75 ohm terminal.

TV BACK

SPLITTER

CABLE

SATELLITE RECEIVER

VCR

Note: RF Antenna can be

connected directly to the 75

ohm terminal. In fringe recep-

tion areas, it may be better to

connect separate RF antennas.

NOTE: When the television is powered on for the first time, it automatically checks to make sure an RF

input signal is connected. After you have made all necessary connections, continue as follows...

1. Press the CHANNEL UP key to automatically search and scan for available channels: Digital (DTV) and

Analog (NTSC). The Channel Search contains two processes that are executed simultaneously for digital and

analog channels, therefore, this will take a few minutes.

NOTES:

The on-screen message for digital search will appear with the channel number, a progress bar, and

percentile number displayed across the bottom of the screen (to indicate activity) as the search process

continues. This may take some time, so please be patient.

Channel information found during the channel search is stored in the Channel Scan Memory database.

The HD television will be tuned to the lowest Digital channel or lowest Analog channel if no digital

channels are found.

2. To change the initial analog tuning system setup (from antenna to cable or cable to antenna), use the on-screen

menu. See “Antenna Selection” on page 17.

3. After channel search is complete, the TV will begin Auto Clock setting. This feature searches for a local PBS

station that is broadcasting an extended data service signal. This signal is used to automatically set the clock/day.

(This may take several seconds.)

To cancel auto clock setting, press the CHANNEL UP key. (To set the clock manually, see page 20.)

First

Please connect all signals

and antennas to jacks and

the terminals on the back.

Then press the Channel UP key.

CATV FRANCHISE NOTE:

Cable companies, like public

utilities, are franchised by

local government authorities.

To receive cable programs,

even with equipment which

is capable of receiving cable

channels, the consumer

must subscribe to the cable

company’s service.

Please wait,

while your TV searches

for available channels.

Digital Antenna 35

50%

Setting Up the TV

Signal Connection

ANALOG

SIGNAL

DIGITAL

SIGNAL

Please wait,

Automatic clock setting.

Press Channel UP Key to cancel.

8 HDMI Connection / Connecting a DVI Set-top Box to HDMI

This is the best option for picture and sound! Using the HDMI connection, which has high-definition

content protection, provides you with uncompressed digital video and audio. As Real As It Gets!

Connecting External Equipment to HDMI (Includes HDCP copy protection)

To avoid problems with some brands of external equipment, follow this procedure when connecting cables and

powering on your equipment.



Switch off TV and external equipment before connecting cable. (Cable is not supplied.)



Connect the external equipment’s high bandwidth HDMI Output to the TV’s HDMI input. This connection

requires only one cable, and includes uncompressed video and Dolby 5.1 or PCM sound.



The TV must be turned on first, press POWER.



Then turn on your external equipment.



Press INPUT to select HDMI to view digital

program.

QuickTips

■

If the television HDMI

pin configuration is

different from the

pin configuration on

your set-top box, you

will need to use an

Adapter for Step 1

connection.

■

To connect DVI to

HDMI, you will need

to use a DVI to HDMI

Cable or an adapter

to make the connec-

tion in Step 1.

■

With a DVI connec-

tion, make sure you

connect Audio out

to the TV’s Compo3

Audio in.

■

Because the Compo-

nent (Compo3) audio

jacks are used to

receive the audio from

the DVI device, the

Compo3 video jacks

cannot be used when

a DVI device is con-

nected.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

Connecting STB with DVI Output to HDMI Input (Includes HDCP copy protection)

Using a DVI to HDMI cable provides better picture quality than standard component or composite

connections, but to receive sound, a separate audio connection is required.

To avoid problems with some brands of external equipment, follow this procedure when connecting cables and

powering on your equipment.



Switch off TV and STB before connecting cables. (Cables are not supplied.)



Connect the STB’s DVI Output to a “DVI to HDMI Cable;” then connect the cable to the TV’s HDMI input.

Note: Check with your local electronic store for a DVI to HDMI Cable that matches your equipment

and the TV.



Connect the STB’s Audio L/R to the TV’s Component Audio 3 L/R.



The TV must be turned on first, press POWER.



Then turn on your external

equipment.



Press INPUT to select HDMI

to view digital TV programs.

Press INPUT key after

connecting cables to access the

A/V inputs.

There is NO need to tune to a

blank channel.

Remote Control

INPUT

RESET

DVD

VCR

CABLE

TV

AUXSAT

POWER





What you will need for connections:



19 Pin HDMI Digital Cable – 1

(Make sure you check the pin configuration

of the cable plug-end

*

)

*

Adapter may be required

Digital A/V Connections

ANALOG

AUDIO

OUTPUT

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT OUT

(1080i/720p/480p)

(1080i/720/480p)

Y

P

B

P

R

A/V OUT

(480i)

S-VIDEO

OUT

VIDEO

RGB OUT

AUTHORIZED

SERVICE ONLY

DVI

OUTPUT

L

R

DVI to HDMI

CABLE

SET-TOP BOX









TV BACK

JACKS

What you will need for

connections:



DVI to HDMI Cable – 1



Audio Cable – 1

ANALOG

AUDIO

OUTPUT

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT OUT

(1080i/720p/480p)

(1080i/720/480p)

Y

P

B

PR

A/V OUT

(480i)

S-VIDEO

OUT

AUDIO

L

R

VIDEO

RGB OUT

AUTHORIZED

SERVICE ONLY

HDMI

OUTPUT

L

R



SET-TOP BOX

HDMI CABLE





IMPORTANT FACT:

When using HDCP

(High Definition

Content Protection)

you may not be able

to copy material that

is copyrighted by the

content owner.

Analog Connections: S-Video and A/V Jacks 9

Using Component Jacks to connect a DVD Player

or other digital equipment

The Component Video jacks will accept HDTV, EDTV, or SDTV

video content.

Switch off TV and external equipment before connecting cables.

(Cables are not supplied.)

Follow these steps to easily connect your STB or DVD to this HDTV:



Connect DVD Player or other digital equipment’s Component Video

Out to the TV Component Video (Compo 3) or (Compo 2) Input

jacks.

 Connect DVD Player or other digital equipment’s Audio Out to the

TV Component Audio 3 or Audio (Video 2) 2 Input jacks.

 Press POWER to turn on the TV. Turn on external equipment also.

 Press the INPUT to select COMPONENT3 or COMPONENT2 to

view the DVD program.

Note: To connect additional digital external equipment, use

either set of component video audio jacks.



ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

P

b

P

r

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

VIDEO OUT SELECT

COPONENT

S

Y

P

B PR

AUDIO OUT

RL

VIDEO OUT

COMPONENT VIDEO OUT

S-VIDEO OUT

DIGITAL

OUT

OPT.

YPbPr RGB

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT OUT

(1080i/720p/480p)

(1080i/720/480p)

Y

P

B

P

R

A/V OUT

(480i)

S-VIDEO

OUT

AUDI O

L

R

VIDEO

RGB OUT

AUTHORIZED

SERVICE ONLY

HDIM

OUTPUT

ANT LOOP OUT

ANT IN

OUTPUT

SELECTION

DIGITAL AUDIO

OUT

(OPTICAL)



DVD PLAYER

CABLE OR SATELLITE

SET-TOP BOX BACK

TV BACK COMPONENT JACKS

What you will need for connections:



Component Video Cable—1 (2)



Audio Cable—1 (2)





Remote Control

INPUT

RESET

123

DVD

VCR

CABLE

TV

AUXSAT

POWER

123





Using S-Video Jacks to connect a DVD Player and VCR

to A/V jacks

Switch off TV and external equipment before connecting cables. (Cables

are not supplied.) Follow these steps to easily connect your DVD or

VCR.



Connect DVD Player or other equipment’s S-Video Out to the TV

S-Video In 1 or 2 Jacks.

Note: S-Video jacks override Video jacks.

 Optional

Connect VCR’s Audio Video Out to the TV Audio Video 1 or 2 Input

jacks.

For Mono VCR (Single Audio Jack) connect VCR Audio Out to TV

Audio (L) Input.

 Press POWER to turn on the TV. Turn on external equipment also.

 Press the INPUT to select VIDEO 1 or VIDEO 2 to view the DVD

or VCR program.

VIDEO OUT SELECT

COPONENT

S

Y

P

B PR

AUDIO OUT

RL

VIDEO OUT

COMPONENT VIDEO OUT

S-VIDEO OUT

DIGITAL

OUT

OPT.

ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

3 4

R-AUDIO-L

R-AUDIO-L VIDEO

VIDEO

VHF/UHF

TO TV

FROM ANT.

RF

CHANNEL

IN

OUT

IN

OUT

Back View of VCR

TV AV Input Jacks

DVD Player





Notes:

AV1 and AV2 jacks have identical functions. Any compatible video

device can be connected to either set of jacks.

A solid Blue screen with the word VIDEO1 or VIDEO2 displayed

means that the Video mode is selected, but no signal is being

detected at the Video jacks. Check connections and turn on

external equipment.

Composite jacks offer only 480i (SDTV) resolution.

Press INPUT key after

connecting cables to access

the A/V inputs.

There is NO need to tune to a

blank channel.

Analog A/V Connections

10 Connecting Digital or Analog Audio to Stereo Amplifier

Connecting Digital Audio Output to an External Amplifier

Using this optical digital connection minimizes electrical noise to help assure high quality signal transfer.

Switch off TV and external equipment before connecting cables. (Cables are not supplied.) Remove the protective

cover before connecting cable to TV digital optical jack.

CAUTION: DO NOT look directly at the laser light.



Connect one end of the optical cable to the TV Digital Audio Output and the other end to the Stereo Amplifier

Optical Digital Input.

 Press POWER to turn on the TV. Turn on external equipment also.

Notes:

DO NOT connect external speakers directly to the TV.

When TV Speakers is in the ON mode, sound will be reproduced through your TV and stereo amplifier.

When TV Speakers is in the OFF mode, sound will be reproduced only through

the stereo amplifier. (See page 20 to set TV speakers.)

QuickTips

■

Position your TV at

least 2 feet from

stereo speakers.

The magnets in

the speakers may

affect the picture

quality.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

P

b

P

r

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

STEREO

AMPLIFIER

REMOTE CONTROL

INPUT

RESET

123

DVD

VCR

CABLE

TV

AUXSAT

POWER

123



ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

COMPO 2

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

BACK OF TV

Connecting Audio Out Jacks to a Stereo Amplifier

Switch off TV and external equipment before connecting cables.

(Cables are not supplied.)



Connect the TV Audio Out (R/L) to the Stereo Amplifier In (R/L).

 Press POWER to turn on the TV. Turn on external equipment also.

Notes:

DO NOT connect external speakers directly to the TV.

When TV Speakers is in the ON mode, sound will be

reproduced through your TV and stereo amplifier.

When TV Speakers is in the OFF mode, sound will be

reproduced only through the stereo amplifier. (See page 20

to set TV speakers.)

STEREO AMPLIFIER

What you will need for connections:



Optical Digital Audio Cable – 1

What you will need for connections:



Audio Cable – 1



BACK OF TV

OPTICAL DIGITAL

CABLE

Audio Connections

Typical Home Theater Connections 11

Typical Home Theater Connections

DIGITAL

AUDIO OUT

COMPONENT OUT

(1080i/720p/480p)

Y

P

B

PR

A/V OUT

(480i)

S-VIDEO

OUT

AUDIO

L

R

VIDEO

AUTHORIZED

SERVICE ONLY

IN

OUT

RJ11/

PHONE

HDMI

ANALOG

AUDIO

OUTPUT

L

R

Y

COMPO 3

Pb

Pr

VIDEO

SERVICE

UHF/VHF/CATV

S-VIDEO

AUDIO

(MONO)

AUDIO 3

VIDEO 2

COMPONENT VIDEO INPUT

VIDEO 1

DIGITAL

AUDIO

OUTPUT

HDMI

INPUT

DIGITAL

ANTENNA IN

L

R

Surround

Sound System

DVD Player

Digital Video Recorder

Analog

VCR

Analog

Cable or

VHF/UHF

Antenna

Splitter

Cable Box /

Sat. Receiver

L

R

AUDIO OUTPUT

VIDEO OUTPUT

VIDEO S-VIDEO COMPONENT VIDEO

ANALOG

AUDIO

YCb Cr

34

RF

CHANNEL

R-AUDIO-L

R-AUDIO-L VIDEO

VIDEO

IN

OUT

VHF/UHF

TO TV

FROM ANT.

OUT

IN

CD TAPE

IN IN OUT

VIDEO

AUDIO

R

OPTICAL

DIGITAL INPUT

L

R

DVD SAT VCR TV

FRONT SPEAKERS (8Ω)

REAR SPEAKERS (8Ω)

CENTER SPEAKER (8Ω)

SUBWOOFER (8Ω)

L

R

AUDIO OUTPUT

VIDEO OUTPUT

ANALOG

AUDIO

S-VIDEOVIDEO

SAT IN

HD

ANT IN

VIDEO OUTPUT

COMPONENT VIDEO

YCb

Cr

IN OUT

COMPO 2

Digital

Antenna



Mode Keys—Use these keys to program the remote control and to select the

operating mode (VCR, TV, CABLE, DVD, SAT, or AUX). To Operate Your...

VCR—Press the VCR key; Television—Press the TV key; Cable Box—Press the

CABLE key; DVD Player—Press the DVD key; and Satellite Receiver—Press the

SAT

key.

Note: Make sure you hold

down the mode key while entering a code number,

see page 13.



Input Key—Press this key to change the input signal source as follows:

In the TV, DVD, Cable, and Satellite modes, this key selects the program source

to display on the screen (TV signal or signal from equipment connected to the AV

jacks). In the VCR mode, this key functions as a VCR’s TV/VCR key.



Power Key—Press to turn TV on or off.



Number Keys—Two keys must be pressed to select a direct channel. Example:

Press 0 then 6 to select channel 6. For Analog channels above 100, press and hold the

1 key until C1–– appears.



Tuner Key—Use this key to toggle from one tuning system to another, digital

channels and analog channels.



Channel (CH up / down) and Volume (VOL – /+) Keys—Press Up/down

keys to tune to the next higher or lower channel in the Channel Scan Memory

database. Press the – /+ keys to adjust volume. The screen displays a left or right

red arrow that blinks as many time as you press the Vol –/+ keys.



Pix Shape Key—Use this key to change the video display format. Available

options depend on signal received and the broadcast aspect ratio: For HT27744/

HT32744—Letter box, Zoom, and Normal. For HT30744—Full, Zoom1/2, and

Normal. (See explanation of image shapes on page 5.) Note: If PAP feature is

selected, this key is not operable.



Sleep Key—Press this key, then press the “0” key to set the Sleep Timer. The

desired time can be set from 30 minutes up to 3 hours in 30 minutes increments.

Sleep Timer will switch off the TV automatically.

Note: The Sleep Timer cancels when the TV is turned off or if a power failure

occurs.



Recall Key—Select the first channel you want to watch; then select another

channel using the number keys. Press Recall to easily switch between the channels

without entering the channel numbers again.

Note: The Recall key can only toggle between channels within the same

signal source. Recall between a Digital channel and an Analog channel will

not work.

It takes only one remote to operate your TV and other equipment. Simply follow the

instructions on pages 13 ~ 15.

Point towards TV / Equipment

ANALOG

RF

DIGITAL

RF

VIDEO

1

VIDEO

2

COMPO

2

H

DMI

COMPO

3

PAUSEREC STOP

ON/OFF QUIK

VOL

CH

MUTETUNER

INPUT RESET

PLAY

SWAP

PAP

PAP CHANNEL

FREEZE

AUDIO

SLEEP

PIX SHAPE

RECALL

CAPTION

INFO

654

78

0

9

123

DVD

VCR

CABLE

TV

AUXSAT

POWER

654

78

0

9

123

GUIDE

E

X

I

T

M

E

N

U

PAGE

UP

DOWN

ENTER

12 Remote Control













15











18

11

13

12

14

16

17

Install Batteries as shown (2 AA, not included)

Notes:

Do not mix old batteries with new ones or mix different types of batteries together.

Remove the batteries if the remote control will not be used for a month or more.

Weak batteries may leak and cause damage. (Normal battery life is roughly six months.)

Using the Multimedia Remote Control

Remote Control Key Functions 13



Menu selection and navigation keys—Use these

keys as follows:

Menu key—Press this key to display the on-screen

menu.

Cursor ▲ (up) /▼ (down) keys—Press these keys to

move the cursor up and down within the menu.

Cursor

3 (left) /4 (right) keys—Press these keys to

move the cursor left and right within the menu.

Exit key—Press this key to exit from the menu

system.

Reset Key—Press twice to restore factory settings.

The TV will automatically start Channel Search and

clear all customized settings. These features will auto-

matically reset:

•

Picture/Sound Adjustments: Color, Tint, Contrast,

Brightness, Sharpness, Color Enhancer, Bass,

Treble, and Surround Sound

•

Channel Memory

•

Initial Channel to OFF

•

Audio to Stereo

•

Caption to OFF

•

V-Guide to OFF

•

TV Speakers to ON

•

Digital Audio Output to Dolby Digital

•

Scan Velocity to HIGH

•

Picture-And-Picture (PAP) to OFF

•

Menu Language to English

•

Auto Clock and Sleep Timer (if previously set)

•

Video to TV (if previously set)

If desired, personal settings can be made again using

the menu options.

Mute Key—Press once to minimize the volume.

Press again to restore.

Note: When using the audio out jacks this key

will not mute the sound.

Audio Key—Press to select the desired audio

reception feature options (if available) for...

DIGITAL: Main, Sub1, Sub2, Sub3, etc.

ANALOG: Stereo, Mono, SAP.

Info Key—Press to display the Digital and Analog

Full Banner information:

Digital Full Banner display–Contains a two-part

Channel Number (Major and Minor). If available

the following is also included–Station ID, Program

Title, Current Time & Date, Antenna Signal Strength,

Signal Format, Program Rating, and Audio Mode.

Analog Full Banner display–Contains Channel

Number (analog antenna/cable), Current time & Date

(if set), Station ID (if available), Program Title (if

available) and Audio Mode.

Caption Key—Press to select analog or digital

caption. The Analog Caption modes are: CC1, CC2,

Quikcap and OFF. The Digital Caption modes are:

Digital CC1~CC6, Quikcap and OFF.

Digital Captions can also be customized to change

the text font type, size, style, background and edge

colors. (See page 18.) Note: These feature are

operable only when digital caption service is

available.

Guide Keys—Press the following keys to operate

your satellite receiver once the remote is

programmed:

Page/Guide key—Press to display menu guide.

Up/Down key—Press the cursor up/down to move

within the menu display.

VCR/DVD Keys—These keys control VCR or DVD

functions for Fast Forward (44), Rewind (33), Play

(4 ), Record (REC), Stop (

■), Tracking (–/ +), and

Pause.

PAP Keys—See page 21 for split-screen

Picture-and-Picture.

QuickTips

■

Be sure batteries are

installed correctly.

■

Point the remote

control toward the

equipment you want

to operate. Objects

between the remote

control and the equip-

ment may cause

misoperation of the

remote control

function.

■

If the remote control

does not work: Press

TV key (see item 1).

■

The remote control

must be programmed

before it will operate

your VCR, DVD

Player, Satellite

Receiver, or Cable

Box.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

13

14

12

11

15

16

17

18

PROGRAMMING THE REMOTE CONTROL

1. Find your VCR, Cable Box, DVD Player, and Satellite Receiver brand codes in

the charts on page 14.

2. Press and hold the VCR, CABLE, DVD, SAT (Satellite Receiver) or AUX

(Auxiliary) mode key while entering a three-digit code number. Then release

the mode key.

If the code was accepted, the mode key will flash 5 times after it is released. If you

entered an invalid code, the mode key will not flash. Check the code number and

repeat Step 2.

After entering each code number check the unit’s operation by pressing the Power

and/or Channel keys. If these keys operate your equipment, you have probably

entered the correct code number for that device. If not, follow Step 2 and enter

another code, if available.

Perform Steps 1 and 2 for each piece of equipment you have.

The VCR, Cable Box, DVD, and

Satellite modes will accept only each

mode’s specific code type.

The AUX mode will accept all code

types, but only one code at a time.

After you have programmed the

remote control and confirmed its

operation, enter your codes in the

spaces provided for easy reference.

VCR Code:

LIST DEVICE HERE

LIS T DEVICE HE RE

AUX

Satellite Code:

Cable Box

Code:

DVD Player

Code:

Virtual Channel

Major

Minor

Antenna Signal

Current Time/Date

Program Rating

Audio

Mode

Station ID

Signal Format

Program

Title

Current Time/Date

Program RatingAudio Mode

Station ID

Program Title

Channel No.

14 Remote Control Programmable Codes

Brand Name Codes

Akai 529

Apex

535, 534, 533, 525, 527,

528, 523

Broksonic 536

Daewoo 529

Denon 501, 520

Emerson 540, 521, 524, 527

Fisher 500

GE 541, 504

Hitachi 530

JVC 515, 510

Kenwood 507

Koss 522

Lasonic 544

Magnavox 508, 502

Marantz 508

Mintek 543

Norcent 532

Onkyo 516, 502

Optimus 511

Orion 526

Oritron 522

Panasonic 501, 518

Philips 508, 502

Pioneer 542, 537, 511, 505, 518

Proscan 504

RCA 539, 538, 504

Samsung 512

Sanyo 500, 526

Sharp 531, 517

Sony 506

Sylvania 524

Symphonic 524

Technics 501

Theta Digital 511

Toshiba 502, 526

Yamaha 501

Zenith 521, 514, 502

Brand Name

Codes

AlphaStar 431

Echostar 432, 410, 416

ExpressVU 432

Fujitsu 404

GE 426, 436, 437, 423

General Instruments 425, 427, 415, 435, 405

Hitachi 407, 421

HTS 432

Hughes 442, 407

Janeil 404

Jerrold 425, 427

JVC 432

Magnavox 429, 430

Memorex 430

Next Level 415

Optimus 430

Panasonic 441, 428, 400

Philips 439, 438, 429, 430, 432

Primestar 425, 427

Proscan 426, 436, 437, 423

Radio Shack 415

RCA 426, 436, 437, 423

Samsung 440

Sony 420

Star Choice 415, 435

Toshiba 422, 405

Uniden 429, 430, 406, 409, 412

Video Pall 404

Viewstar 418

Zenith 434, 404

DVD CODES

SATELLITE RECEIVER CODES

Brand Name Codes

Admiral 234, 243, 247, 224, 229, 222, 215

Adventura 228

Aiko 205

Aiwa 228, 217

Akai 209, 215

America Action 205

America High 232

Bell&Howell 201

Broksonic 234, 243, 247, 227, 204

Candle 248, 222, 204, 205, 211, 217

Canon 232

CCE 205

Cineral 205

Citizen 222, 205, 211, 217

Craig 202, 219

Craver 204

Curtis Mathes 232, 236, 238, 248, 222, 228, 209,

211, 217

Daewoo 205, 211

Daytron 205

Denon 230

Dynatech 228

Emerex 214

Emerson 251, 228, 243, 234, 236, 247, 227,

201, 204, 205, 206, 210, 211, 217

Fisher 200, 201, 202, 211

Fuji 232

Funai 228, 217

GE 222, 246, 248, 232, 236, 226, 229,

224, 212

Goldstar 253, 238, 248, 226, 206, 215, 217

Go Video 248, 249, 212, 219

Gradiente 228

Garrard 228

Harley Davidson 228

Headquarter 200

Hitachi 228, 230, 246, 226, 222, 209, 217

Hughes 230

JBL 237

Jensen 209

JVC 220, 238, 226, 201, 209, 230

KEC 205

Kenwood 220, 226, 238, 201, 209

Kodak 232

Lloyd’s 228

Logik 219

LXI 232, 228, 230, 201, 202, 206,

211, 217

Magnasonic 205, 219

Magnavox 204, 232, 228, 211, 217, 219, 220

Marta 206

Matsushita 232

MEI 232

Memorex 227, 232, 243, 245, 224, 228, 229,

230, 200, 201, 202, 206, 215

Minolta 230

Mitsubishi 244, 224, 226, 229, 210

Motorola 232, 229, 224

Brand Name Codes

MTC 228, 217, 219

Multitech 228, 217

NEC 238, 226, 201, 206, 209, 215,

217, 248

Olympus 232

Optimus 245, 248, 224, 229, 201

Orion 243, 227, 234, 205, 206,

210, 211

Panasonic 245, 232, 236, 202, 211, 219

Penny 230, 232, 248, 211, 219

Pentax 238, 230

Philco 204, 232, 243, 228, 217

Philips 204, 232, 228, 211, 217

Pioneer 242, 204, 207, 220

Proscan 222, 241, 246, 230, 236, 226

Proton 219

Pulsar 248, 205, 217

Quarter 200

Quartz 200

Quasar 245, 232, 236

Radio Shack 228, 245

RCA 250, 222, 241, 246, 248, 230,

232, 236, 224, 226, 229, 201,

207, 210

Realistic 232, 248, 224, 228, 229, 200,

201, 202, 206, 217

Samsung 248, 211, 217, 222

Samtron 248

Sansui 243, 226, 228, 209, 219, 220

Sanky 229, 224

Sanyo 200, 201, 202

Scott 234, 247, 227, 211

Sears 232, 228, 230, 200, 201, 202,

206, 211, 217

Semp 211

Shintom 219, 227

Sharp 252, 229, 224

Signature 228, 217, 229, 224, 200

Sony 214, 218, 232, 237, 226, 228

STS 230

Sylvania 228, 232, 244, 204, 217

Symphonic 228, 217, 226, 202

Yamaha 238, 226

Tatung 226, 209

Teac 228, 209, 214, 217

Technics 232

Teknika 232, 228, 217

Toshiba 211, 244, 202, 205, 210

Tomas 228, 217

Vector 211

Video Concept 211

Wards 230, 232, 248, 224, 228, 229,

202, 204, 211, 217

White Westinghouse 243, 205

XR-1000 228, 232

Yamaha 238, 226

Zenith 206, 215, 237, 243, 220,

228, 222

VCR CODES

Brand Name Codes

ABC

312, 304, 306, 309, 313, 314, 318,

319, 321, 324, 329

AIM 321

Archer 334

Bell & Howell 313, 314, 329

Contec 305, 302, 307, 309, 318, 320, 324

CPI 309, 323

Diamond 320

Eagle 313, 314, 329

Emerson 334

Gemini 334

General Instruments 303, 300, 309, 320, 321, 323

Goldstar 312

Goodmind 334

Hamlin 330, 320

Hitachi 309, 323

Hytex 318

Jerrold

300, 303, 309, 313, 314, 320,

321, 329

Magnavox 325, 301, 309, 313, 314, 323

Memorex 331, 332, 313, 314, 329

Motorola 338, 303, 300, 309, 320, 321, 323

Movie Time 306, 310, 314, 313, 329

Northcoast 316

NSC 305, 306, 314, 313, 329

Oak 305, 318, 320

Paragon 331, 313, 314, 329

Panasonic 331, 324, 302, 307, 317, 327

Philips 341, 325, 301, 309, 313, 314, 323

Pioneer 312, 335, 333, 317, 324

Quasar 331, 302, 307, 317

RCA 328, 302, 307

Regal 330, 307, 320

Rembrandt 305, 309, 323

Radio Shack 334

Samsung 312, 310

Scientific Atlanta 335, 307, 324

Signal 310

Signature 300, 309, 321, 323

Sony 340

Sprucer 302, 307, 316

Starcom 332, 309, 321, 323

Stargate 309, 310, 321, 334

Teleview 310

Tocom 300, 303, 305, 304, 306, 307

Toshiba 331, 309, 316, 323

Unika 314, 313, 329

United Artists 318

United Cable 309, 323

U.S. Electronics 309, 324

Viewstar 326, 313, 315, 314, 329

Wards 321, 309, 323

Warner 312

Zenith 331, 336, 337, 309, 316, 324

CABLE CODES

REMOTE KEYS TV MODE VCR MODE CABLE MODE DVD MODE SATELLITE

MODE

POWER

Turns Unit On/Off Turns Unit On/Off Turns Unit On/Off Turns Unit On/Off Turns Unit On/Off

NUMBER KEYS

(0 ~ 9)

Used to Select

Channels

Used to Select

Channels

Used to Select

Channels

No Function Used to Select

Channels

INPUT

Selects TV/Video

mode

Selects TV/VCR

mode

No Function No Function Selects TV/DSS

mode

RECALL

Selects Previous

Channel

Selects Previous

Channel

Selects Previous

Channel

Select Repeat

Function

Selects Previous

Channel

MENU

Displays Setup

Menu

Displays Setup

Menu

Displays Setup

Menu

Displays Setup

Menu

Displays Setup

Menu

CHANNEL (UP)

Channel Up Channel Up Channel Up Next Ch. Up Channel Up

CHANNEL (DOWN)

Channel Down Channel Down

Channel Down Previous Ch.

Down

Channel Down

VOLUME

– (DOWN)

Audio Down Audio Down Audio Down Audio Down Audio Down

VOLUME

+ (UP)

Audio Up Audio Up Audio Up Audio Up Audio Up

CURSOR

3

(LEFT)

Cursor Left Cursor Left Cursor Left Cursor Left Cursor Left

CURSOR

4

(RIGHT)

Cursor Right Cursor Right Cursor Right Cursor Right

Cursor Right

CURSOR ▲ (UP)

Cursor Up Cursor Up Cursor Up Cursor Up Cursor Up

CURSOR ▼ (DOWN)

Cursor Down Cursor Down Cursor Down Cursor Down Cursor Down

MUTE

Switches TV

sound Off/On

Switches TV

sound Off/On

Switches TV

sound Off/On

Switches TV

sound Off/On

Switches TV

sound Off/On

RESET

Operates TV

ONLY

No Function No Function No Function No Function

CAPTION

Operates TV

ONLY

No Function No Function Accesses Audio

Options

No Function

SLEEP

Operates TV

ONLY

No Function No Function No Function No Function

V-GUIDE

Operates TV

ONLY

No Function No Function No Function No Function

ENTER

Makes Selection Makes Selection Makes Selection Makes Selection Makes Selection

PLAY (

4

)

Selects VCR/DVD

Play Mode

Selects VCR Play Selects VCR/DVD

Play

Selects DVD Play Selects VCR/DVD

Play

FAST FORWARD

(

8

)

Operates VCR/

DVD

Operates VCR Operates VCR/

DVD

Operates DVD Operates VCR/

DVD

REWIND (

7

)

Operates VCR/

DVD

Operates VCR Operates VCR/

DVD

Operates DVD Operates VCR/

DVD

STOP ( ■ )

Selects VCR/DVD

Stop

Selects VCR

Stop

Selects VCR/DVD

Stop

Selects DVD

Stop

Selects VCR/DVD

Stop

PAUSE (II)

Selects VCR/DVD

Pause

Selects VCR

Pause

Selects VCR/DVD

Pause

Selects DVD

Pause

Selects VCR/DVD

Pause

RECORD

(REC

•

)

No Function

Selects VCR

Record

No Function No Function

No Function

TUNER Operates TV

ONLY

No Function No Function No Function No Function

GUIDE No Function No Function No Function No Function Display Guide

Screen

PIX SHAPE Operates TV

ONLY

No Function No Function No Function No Function

INFO Displays Banner Selects Program

Display

No Function Selects Zoom Selects Program

Display

EXIT Ends Selection Ends Selection Ends Selection Ends Selection Ends Selection

PAP Operates TV

ONLY

No Function No Function No Function No Function

Notes:

Many of the keys on this remote control are multi-functional. Please refer to the chart for a generic description of the keys and their functions.

Refer to your original operating manuals for specific feature operation.

This remote control cannot add keys or features to your equipment. Your equipment’s manufacturer must have provided them originally.

REMOTE CONTROL KEYS FUNCTIONS CHART

MODE KEYS Press these keys (VCR/TV/CABLE/DVD/SAT/AUX) when programming the remote

control and to choose an operating mode.

Remote Control Key Functions 15

16 Using the Menu

The on-screen menu provides the viewer with easy access to adjustments and settings. Just use the keys on the remote control and follow the on-screen

instructions.

HOW TO OPERATE THE ON-SCREEN MENU

1. Press MENU key, the Main Menu appears. Note: The Main Menu consists of the Icon Area and the Option Area. If no key is pressed after 30

seconds, the menu disappears from the TV screen.

2. Use the ▲ /▼ keys to move the Cursor to select options from the Icon Area.

3. Press the ENTER key or

4 right arrow to move Cursor from the Icon Area to the Menu Option area.

4. Use the ▲ /▼ keys to choose desired option in the Main and Sub Menus. (Selected item bar is highlighted in yellow.)

5. Press the ENTER key to save the menu setting or to selected a different item.

6. Press

3left arrow to move Cursor from the Menu Option area back to the Icon area or EXIT key to exit from the menu.

Note: Items with submenus require additional steps, basically follow the on-screen directions using the Arrow keys and ENTER key.

MENU NAVIGATION MAP

Move

Select

Back

Exit

ENTER

MENU

EXIT

Size

Color

Style

cc

Main

Channel

Digital Caption Font

V-Guide

Setup

Picture/Sound

Date/Time

Digital Audio Output

TV Speaker

Menu Language

Dolby Digital

Auto Clock

Manual Setup

Time

Date (Day)

Off

On

English

Español

Français

Channel Search

Add

Delete

Channel Scan Memory

Off

On

Initial Channel

Sports

News

Movies

Manual

Color Enhancer

Scan Velocity

Picture

Sound

Surround

Background

Normal

Cool

Low

High

Color

Tint

Contrast

Background

Brightness

Sharpness

Bass

Treble

Off

On

Digital Add-on Search

Off

On

Digital Cable Search

Off

On

Antenna Selection

Off

On

Opacity

Edge Style

Foreground Opacity

Background Opacity

Yes

No

Warm

Off

PCM

Foreground Color

Background Color

Edge Color

ICON AREA

MAIN MENU SUB MENU

MENU NAVIGATION KEYS

(See steps 1~6 for key

operation.)

See page 17.

See page 18.

See page 19.

See page 20.

TV Adjustment and Setup

IMPORTANT FACT: Some Menu

options are specific to Digital and

Analog channels. Therefore, they are

not always selectable.

CHANNEL SEARCH

Channel Search is required only if additional channels become available, such as moving to another

city or having a cable service installed.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Antenna icon. Press ENTER.

3. Use the ▲/▼ keys to select Channel Search. Press ENTER.

4. Use the ▼ key to select ON. Press ENTER.

DIGITAL CABLE SEARCH (Optional)

This TV can receive unscrambled (ClearQAM) digital cable channels, when available.

However, not all cable companies provide ClearQAM digital channels.

Searching for digital cable channels will take about 10 minutes, please be patient.

1. Connect a Digital Cable signal directly to the TV Digital Antenna In jack.

2. Press the TUNER key to select digital channels. Press MENU.

3. Use the ▲/▼ keys to highlight the Antenna icon. Press ENTER.

4. Use the ▲/▼ keys to highlight Digital Cable Search. Press ENTER.

5. Use the ▼ key to choose ON. Press ENTER.

DIGITAL ADD-ON SEARCH

Use this feature to update the digital antenna channel map database to

add new channels or to add channels when broadcast towers

are in opposite directions from your location.

1. Press the TUNER key to select digital channels. Press MENU.

2. Use the ▲/▼ keys to highlight the Antenna Icon. Press ENTER.

3. Use the ▲/▼ keys to highlight Digital Add-on Search. Press ENTER.

4. Use the ▼ key to choose YES. Press ENTER.

Note: Turn your Antenna and repeat these steps for each

direction in which there are transmitting towers.

ANTENNA SELECTION

Use this feature to switch between analog terrestrial channels and

analog cable channels.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Antenna Icon. Press ENTER.

3. Use the ▲/▼ keys to select Antenna Selection. Press ENTER.

4. Use ▼ key to select ON. Press ENTER.

cc

Channel

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Channel Search

Digital Cable Search

Digital Add-on Search

Channel Scan Memory

Initial Channel

Antenna Selection

Digital Add-on Search

cc

Please wait,

while your TV searches

for available channels.

Digital Antenna 35

50%

Power off

Power

cc

Channel

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Channel Search

Digital Cable Search

Digital Add-on Search

Channel Scan Memory

Initial Channel

Antenna Selection

cc

Digital Cable Search

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Digital Cable

Channel Search

OFF

ON

cc

Channel

Channel Search

Digital Cable Search

cc

Antenna Selection

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Switch

Antenna?

Off

On

cc

Channel

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Channel Search

Digital Cable Search

Digital Add-on Search

Channel Scan Memory

Initial Channel

Antenna Selection

(Continued on page 18.)

IMPORTANT FACT: This TV only maintains one database of digital channels. Therefore, when

you search for ClearQAM digital cable channels, the database of antenna digital channels will be

deleted. You will only be able to receive those ClearQAM channels your cable company provides.

Cable companies rearrange virtual channels as programming

changes which may cause the program you are watching to

move to another channel. This will appear briefly to notify you

of this change. You have to relocate the program you were

watching by scanning through the channels.

When a terrestrial broadcast station rearranges its virtual channels, data in the PSIP tables

advises the TV of the change. This allows the TV to “follow” a program to its new virtual

channel. The viewer should not even realize a change has occurred.

To restore the antenna digital channel database, reconnect the antenna and use the menu

system to perform normal channel search.

Program change

from cable company

Channel Search / Digital Cable, Add-on Search / Antenna Selection 17

Captioning is textual information transmitted along with the picture and sound so it can be displayed on the TV

screen. Because different types of captions can be transmitted with the TV signal, separate captioning modes are

provided. The captioning modes recognized by this model are: Analog EIA-608B and Digital EIA-708B. Local

broadcasters decide which caption signals to transmit.

cc

Digital Caption Font

Back

Ba ck

Select

Se lect

Exit

ENTER

MENU

Move

EXIT

Size

Style

Color

Opacity

Edge Style

cc

Size

Back

Ba ck

Select

Exit

ENTER

MENU

Move

EXIT

Default

Small

Standard

Large

IMPORTANT FACT: Receiving a true EIA 708B Digital Closed-Captioning... Some

broadcasters upconvert 608B Analog Caption to include in their digital stream. These

upconverted Analog captions may not respond to all the options for customized settings.

CC1

Digital CC1

Analog Caption

Digital Caption

To V iew Captions:

1. Press the CAPTION key on the remote to select: Analog caption—CC1, CC2, QuikCap or Off.

Digital caption—Digital CC1, Digital CC2, Digital CC3, Digital CC4, Digital CC5, Digital

CC6, Quikcap, or Off.

2. Using the Quikcap feature enables you to turn captioning on and off with the Mute function.

Press the MUTE key on the remote control to block the TV sound; the captions display auto-

matically. Press again to restore sound, captions will disappear.

To Customize Digital Captioning On-screen Display:

This feature is designed to customize Digital Captioning only.

1. Press the TUNER key to select Digital. Press MENU.

2. Use the ▲/▼ keys to highlight the Caption icon. Press ENTER.

3. Use the ▲/▼ keys to select desired options. Press ENTER.

4. Use the ▲/▼ keys to make adjustment.

NOTE: The item customized will be highlighted with a yellow border and

a bright yellow bullet to indicate selection.

5. To adjust other options, repeat steps 3~5.

6. Press MENU to return to the Main Menu or press EXIT to exit from the menu.

Main Menu

Closed-Captioning

INITIAL CHANNEL

The television can be programmed to tune to your favorite channel each time it is powered on,

such as your favorite news or sports channel.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Antenna Icon. Press ENTER.

3. Use the ▲/▼ keys to select Initial Channel. Press ENTER.

4. Use the ▼ key to select ON. Press ENTER.

5. Press the TUNER key to choose Digital or Analog.

6. Select your favorite channel using the CHANNEL Up/Down keys on the remote.

7 Press the ENTER key to set the initial channel, or to clear the channel if you would like to

change the channel number.

8. Press MENU to return to the Main Menu or EXIT to exit from the menu.

cc

Initial Channel

Press ENTER Key to set.

Use Channel UP/DOWN Keys

Off

On

Digital Antenna 24-1

Ch

Back

Ba c k

Exit

Exi t

ENTER

TUNER

Tuner

Select

Se l e ct

MENU

EXIT

Sub-Menu

cc

Channel

Back

Select

Exit

Exi t

ENTER

MENU

Move

EXIT

Channel Search

Digital Cable Search

Digital Add-on Search

Channel Scan Memory

Initial Channel

Antenna Selection

cc

Digital Antenna 06-1

Channel Scan Memory

Deleted

Num

Ch

Back

Exit

ENTER

TUNER

Tuner

Add/Del

0~9

0 ~ 9

MENU

EXIT

CHANNEL SCAN MEMORY

Channel scan memory is a list of active channels that you can scan through when using the

Channel Scan (up/down) keys. This list can be customized by deleting unwanted channels.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Antenna Icon. Press ENTER.

3. Use the ▲/▼ keys to select Channel Scan Memory. Press ENTER.

When the CH Scan Memory option is selected, the Channel Add/Delete menu appears.

The current channel number will also appear in the box.

4. Press the TUNER key to select Digital or Analog.

5. Use the CHANNEL Up/Down keys or numerical keys to select desired channel.

6. Press the ENTER key to delete or add the channel.

18 Initial Channel / Closed-Captioning

QuickTips

■

The V-Guide menu

display remains on

screen for approxi-

mately 30 seconds. If

it disappears, press

the V-GUIDE key.

■

You can block a

content rating such as

TVPG-V and still be

able to watch TVPG

programs with ratings

of S-L-D provided the

TVPG is unblocked.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

NOTE: THIS FEATURE IS DESIGNED TO COMPLY WITH THE UNITED STATES OF AMERICA’S FCC

V-CHIP REGULATIONS. THEREFORE, IT MAY NOT FUNCTION WITH BROADCASTS THAT ORIGINATE

IN OTHER COUNTRIES.

This Sanyo television is equipped with an electronic V-Chip to interpret MPAA and TV Parental Guidelines rating codes.

When these codes are detected, the TV will automatically display or block the program, depending upon choices you make

when setting up the V-Guide system. Content ratings are represented by the initials: FV (fantasy violence), D (suggestive

dialog), L (adult language), S (sexual situations), and V (violence).

A rating icon will generally appear in the upper left hand corner of the TV screen for about fifteen seconds at

the beginning of a program.

cc

V-Guide

Back

Ba c k

Select

Se l ect

Exit

ENTER

MENU

Move

EXIT

Do you want to enter the

V- Guide system and set

the rating limits?

YES

NO

UNRATED

GUIDELINES

(Light Gray)

Move

Select

Back

Exit

Ex it

ENTER

MENU

EXIT

Rating

cc

Allow All

Block All

TV-Y7

TV-Y

TV-G

TV-PG

TV-14

MOVIE

PG

PG13

R

NC17

X

TV-MA

TV

FV

D L S V

G

LOCKED SYMBOL

MOVIE RATING

TV RATING

RATED

GUIDELINES

(Dark Gray)

V-GUIDE RATINGS—AT-A-GLANCE

V-Guide (Parental Control) Operation

This television can be set to block programs automatically with content

you deem as inappropriate for your children to view.

TO BLOCK MOVIE OR TV PROGRAM

1. Press MENU.

2. Use the ▲/▼keys to highlight the V-Guide Icon [Locks & Keys]. Press

ENTER.

3. Use the ▲/▼ keys to select YES. Press the ENTER.

4. Use the ▲/▼, / keys to select Movie or TV ratings.

5. Press the ENTER key to active selected option.

For Movie Ratings: A lock symbol will appear beside the selected

option indicating it is blocked.

For TV Ratings: A locked symbol appears in the rating boxes

indicating blocked rating.

6. Press MENU to return to the Main Menu or press EXIT to exit from

the menu.

TO TEMPORARILY UNBLOCK MOVIE OR

TV PROGRAM

1. Press MENU.

2. Use the ▲/▼ keys to highlight the V-Guide Icon. Press ENTER.

3. Select “NO” to temporarily unblock settings.

TO UNBLOCK MOVIE OR TV PROGRAM

1. Press MENU.

2. Use the ▲/▼ keys to highlight the V-Guide Icon. Press ENTER.

3. Use the ▲/▼ keys to select “YES,” only if the option indicator

(yellow bullet) is not highlighted. Press ENTER.

4. Highlight the “ALLOW ALL” option using the ▲/▼, / keys, if

needed. Press ENTER to clear all settings.

IMPORTANT FACT: The TV will automatically block (locked

symbol) ratings above or unblock (no lock) ratings below selec-

tion. For example, if you block TV rating TV-G, the ratings

TV-PG, TV-14 and TV-MA will be blocked automatically or if you

block Movie rating PG-13, the ratings R, NC17 and X will be

blocked automatically.

Blocking TVY7 does not block higher ratings.

▲

Move

Select

Back

Exit

ENTER

MENU

EXIT

Rating

cc

Allow All

Block All

TV-Y7

TV-Y

TV-G

TV-PG

TV-14

MOVIE

PG

PG13

R

TV-MA

TV

FV

D L S V

G

NC17

X

EXAMPLE: MOVIE RATING: NC17 & X (BLOCKED)

TV RATING: TV-14 & TV-MA–D,L,S, & V (BLOCKED)

V-Guide Operation 19

Setting the Clock Manually

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Setup Icon. Press ENTER.

3. Use the ▲/▼ keys to select Date/Time. Press ENTER.

4. Use the ▲/▼ keys to select Manual Setup. Press ENTER.

5. Use the ▲/▼ keys to select the correct Hour. Press ENTER to set hour.

(The TV will go automatically to the next setting.)

6. Use the ▲/▼ keys to select the correct Minutes. Press ENTER to set minutes.

(The TV will go automatically to the next setting.)

7. To set the other information, use the ▲/▼ keys to select the correct

information. Press ENTER to set information.

Digital Audio Output

Use this feature to choose the format of the audio output signal: Dolby

Digital or PCM.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Setup Icon. Press ENTER.

3. Use the ▲/▼ keys to highlight the Digital Audio. Press ENTER.

4. Use the ▲/▼ keys to select Dolby Digital or PCM. Press ENTER.

Note: If you are watching an analog channel, or a signal connected to

the Video 1/2 or Component jacks, the Digital Audio output setting is not available.

QuickTips

■

Cursor will continue

to move through the

menu loop until the

Exit key is pressed.

■

The Channel Banner

(Full or Brief) Clock

option will be blank if

the clock/day has not

been set.

■

Surround sound will

be on automatically

when Sports or Movie

is selected. Surround

expands the sound

effect while receiving

MTS stereo signals.

Need help?

Visit our Web site at

www.sanyoctv.com

or Call 1-800-877-5032

Adjust

Ad just

Move

Mo ve

Back

Ba ck

Exit

ENTER

MENU

EXIT

Manual Setup

cc

Hour

Month

Day

Year

Minute

AM/PM

cc

Digital Audio Output

Dolby Digital

PCM

Move

Select

Se l ect

Back

Exit

ENTER

MENU

EXIT

Setup

cc

Date/Time

TV Speaker

Menu Language

Digital Audio Output

Analog Audio Output

When the Picture/Sound Option is selected, press the ENTER key to select the desired option and setting.

To expand your viewing experience, select Sports, Movie, or News to match the program you are watching.

The TV will automatically adjust the sound and picture.

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Picture/Sound Icon. Press ENTER.

Adjusting the Picture/Sound Manually

1. Use the ▲/▼ keys to select Manual. Press ENTER.

2. Use the ▲/▼ keys to select Picture (Options: Color, Tint, Contrast, Brightness, Sharpness), Sound

(Options: Bass or Treble), or Surround (Options: On or Off). Press ENTER.

3. Use the ▲/▼ keys to select desired option setting. Then use the / keys to make adjustments.

4. Press MENU to return to the Main Menu or EXIT to exit from the menu.

Move

Adjust

Ad just

Back

Exit

MENU

EXIT

Picture

cc

Sharpness

Color

Tint

Contrast

Brightness

cc

Picture/Sound

Back

Ba ck

Select

Se l ect

Exit

ENTER

MENU

Move

EXIT

Sports

Movie

News

Manual

Color Enhancer

Scan Velocity

Setup Menu

Picture/Sound Adjustment

▲

cc

TV Speaker

On

Off

TV Speakers

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Setup Icon. Press ENTER.

3. Use the ▲/▼ keys to highlight the TV Speaker. Press ENTER.

4. Use the ▲/▼ keys to select ON. Press ENTER.

NOTE: Sound will not be produced through your television speakers if the OFF mode is selected.

Menu Language

1. Press MENU.

2. Use the ▲/▼ keys to highlight the Setup Icon. Press ENTER.

3. Use the ▲/▼ keys to highlight the Menu Language. Press ENTER.

4. Use the ▲/▼ keys to select English, Español, or Français. Press ENTER.

5. Press MENU to return to the Main Menu or EXIT to exit from the menu.

cc

Menu Language

Back

Ba ck

Select

Exit

MENU

EXIT

English

Español

Français

20 Set-up & Picture/Sound Adjustment

La page charge ...

Sanyo HT27744 Le manuel du propriétaire

Ce manuel convient également à

Sanyo HT27744 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents