MSI K8N Neo3 Le manuel du propriétaire

i

MS-7135 (v1.X) ATX Mainboard

English/ French/ German Version

G52-M7135X3

K8N Neo3 Series

7135v1.1-Preface.P65 2005/2/5, 下午 02:031

ii

Manual Rev: 1.1

Release Date: Feb. 2005

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful interference, in

which case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to

comply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International

MS-7135

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

7135v1.1-Preface.P65 2005/2/5, 下午 02:032

iii

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR

INTERNATIONAL. We take every care in the preparation of this document, but no

guarantee is given as to the correctness of its contents. Our products are under

continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.

AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered

trademarks of AMD Corporation.

Intel

®

and Pentium

®

are registered trademarks of Intel Corporation.

PS/2 and OS

®

/2 are registered trademarks of International Business Machines

Corporation.

Microsoft is a registered trademark of Microsoft Corporation. Windows

®

98/2000/NT/

XP are registered trademarks of Microsoft Corporation.

NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-

marks of NVIDIA Corporation in the United States and/or other countries.

Netware

®

is a registered trademark of Novell, Inc.

Award

®

is a registered trademark of Phoenix Technologies Ltd.

AMI

®

is a registered trademark of American Megatrends Inc.

Revision History

Revision Revision History Date

V1.1 First release for PCB 1.X Feb. 2005

European version

Technical Support

If a problem arises with your system and no solution can be obtained from the user’s

manual, please contact your place of purchase or local distributor. Alternatively,

please try the following help resources for further guidance.

Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,

and other information: http://www.msi.com.tw/program/service/faq/

faq/esc_faq_list.php

Contact our technical staff at: support@msi.com.tw

7135v1.1-Preface.P65 2005/2/5, 下午 02:033

iv

1. Always read the safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the equip-

ment from overheating. DO NOT COVER THE OPENINGS.

6. Make sure the voltage of the power source and adjust properly 110/220V be-

fore connecting the equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

8. Always Unplug the Power Cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause electrical

shock.

11. If any of the following situations arises, get the equipment checked by a service

personnel:

† The power cord or plug is damaged.

† Liquid has penetrated into the equipment.

† The equipment has been exposed to moisture.

† The equipment has not work well or you can not get it work according to

User’s Manual.

† The equipment has dropped and damaged.

† The equipment has obvious sign of breakage.

12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STOR-

AGE TEMPERATURE ABOVE 60

0

C (140

0

F), IT MAY DAMAGE THE EQUIPMENT.

Safety Instructions

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

7135v1.1-Preface.P65 2005/2/5, 下午 02:034

v

CONTENTS

FCC-B Radio Frequency Interference Statement..........................................................ii

Copyright Notice...............................................................................................................iii

Trademarks......................................................................................................................iii

Revision History...............................................................................................................iii

Technical Support............................................................................................................iii

Safety Instructions.........................................................................................................iv

English........................................................................................................................E-1

Français......................................................................................................................F-1

Deutsch......................................................................................................................G-1

7135v1.1-Preface.P65 2005/2/5, 下午 02:035

E-1

Quick User’s Guide

K8N Neo3 Series

(MS-7135 v1.X)

ATX Mainboard

English

E-2

MS-7135 ATX Mainboard

E-3

Quick User’s Guide

Thank you for choosing the K8N Neo3 (MS-7135) v1.X ATX

mainboard. The K8N Neo3 mainboard is based on nVIDIA

®

nForce4-

4X chipset for optimal system efficiency. Designed to fit the advanced

AMD

®

K8 Athlon 64 processor, the K8N Neo3 mainboard delivers a

high performance and professional desktop platform solution.

MSI Reminds You...

Please note that the companion MSI Driver/Utility CD supports this

mainboard with Windows 2000/XP system drivers ONLY.

MS-7135 (v1.X)

Quick User’s Guide

E-4

MS-7135 ATX Mainboard

Mainboard Specifications

CPU

† Supports Socket-754 for AMD K8 Athlon 64 processor

† Supports up to 3700

+

Athlon 64 processor or higher

(For the latest information about CPU, please visit http://www.msi.com.tw/pro-

gram/products/mainboard/mbd/pro_mbd_cpu_support.php)

Chipset

† nVIDIA

®

nForce4-4X

- HyperTransport link to the AMD Athlon 64 CPU

- Supports single-channel DDR333/400 memory

- Supports PCI Express x16/x1 interface

- Two independent SATA controllers, for four drives

- Dual Ultra ATA 133/100/66 IDE controllers

- Supports high-speed USB2.0 ports

Main Memory

† Supports single-channel, four-memory-bank DDR 333/400 using two 184-pin DDR

DIMMs

† Supports a maximum memory size up to 2GB without ECC

† Supports 2.5v DDR SDRAM DIMM

(For the updated supporting memory modules, please visit http://www.msi.com.

tw/program/products/mainboard/mbd/pro_mbd_trp_list.php)

Slots

† One PCI Express x16 slot (PCI Express Bus specification v1.0a compliant)

† One PCI Express x1 slot (PCI Express Bus specification v1.0a compliant)

† Three 32-bit Master 3.3V/5V PCI Bus slots

† One AGR (Advance Graphics Riser) slot for compatible AGP VGA cards

(For more detailed information on compatible AGP VGA cards, please refer to

http://www.msi.com.tw/program/products/mainboard/mbd_index.php)

Onboard IDE

† Dual IDE controllers on the nVIDIA

®

nForce4-4X chipset provides IDE HDD/CD-

ROM with PIO, Bus Master and Ultra DMA 133/100/66 operation modes

† Can connect up to 4 IDE devices

Onboard Serial ATA

† Supports 4 SATA ports with up to 150MB/s transfer rate

MSI Reminds You...

To create a bootable RAID volume for a Windows 2000 environment,

Microsoft’s Windows 2000 Service Pack 4 (SP4) is required. As the

end user cannot boot without SP4, a combination installation CD must

be created before attempting to install the operating system onto the

bootable RAID volume.

E-5

Quick User’s Guide

USB Interface

† 10 USB ports

- Controlled by nForce4-4X chipset

- 4 ports in the rear I/O, 6 ports via the external bracket

NV RAID (Software)

† Supports up to 4 SATA and 4 ATA133 Hard drives

-RAID 0, 1, 0+1, or JBOD supported

-RAID function available for PATA133 + SATA H/D drives

LAN

† Marvell PHY 88E1111 Gigabit Ethernet chip (Optional)

† Realtek 8201 CL 10/100Mb/s Ethernet chip (Optional)

Audio

† RealTek ALC655 6-channel software audio codec

- Compliance with AC97 v2.3 spec.

- Meets PC2001 audio performance requirement

On-Board Peripherals

† On-Board Peripherals include:

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes

- 2 serial ports

- 1 parallel port supporting SPP/EPP/ECP mode

- 10 USB2.0 ports (Rear*4 / Front*6)

- 1 Audio (Line-In/Line-Out/MIC) port

- 1 RJ-45 LAN jack

- 1 CD-In pinheader

- 2 IDE ports support 4 IDE devices

- 4 serial ATA ports

BIOS

† The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral

devices and expansion cards of the board automatically.

† The mainboard provides a Desktop Management Interface (DMI) function which

records your mainboard specifications.

† Supports boot from LAN, USB Device 1.1 & 2.0, and SATA HDD.

Dimension

† ATX form factor: 300mm x 185mm

Mounting

† 6 mounting holes

To create the combination installation CD, please refer to the following

website:

http://www.microsoft.com/windows2000/downloads/servicepacks/

sp4/HFdeploy.htm

E-6

MS-7135 ATX Mainboard

Quick Components Guide

NBFAN1

SFAN1

SW_BAT1

JPW1

FDD1

SATA1

SATA2

SATA3

SATA4

J1

T: LAN Jack

B: USB Ports

Winbond

W83627THF

LAN

B

A

T

+

D

I

M

1

CFAN1

D

I

M

2

JWR1

PCI 3

PCI 2

PCI 1

PCI_E1

PCI_E2

I

D

E

2

I

D

E

1

JFP1

JUSB1

JUSB2

JUSB3

JFP2

JCI1

JAUD1

Top:

Parallel Port

Bottom:

COM Port

Top: Mouse

Bottom: Keyboard

B

I

O

S

Codec

USB Ports

Line-In

Line-Out

Mic

JCOM1

AGR

nVIDIA

nForce4-4X

DDR DIMMs, p.E-10

Back Panel

I/O, p.E-13

JPW1, p.E-11

IDE1/2, p.E-15

JWR1, p.E-11

CFAN1, p.E-15

FDD1, p.E-14

JFP2, p.E-16

PCI Express

Slots, p.E-18

PCI Slots, p.E-18

JAUD1, p.E-16

J1, p.E-14

JFP1, p.E-16

JCI1, p.E-14

JUSB1/2/3, p.E-17

SATA1~4, p.E-14

SW_BAT1, p.E-17

JCOM1, p.E-16

CPU, p.E-7

NBFAN1/

SFAN1, p.E-15

AGR Slot, p.E-19

E-7

Quick User’s Guide

Central Processing Unit: CPU

CPU Installation Procedures for Socket 754

1.Please turn off the power and

unplug the power cord before

installing the CPU.

2.Pull the lever sideways away

from the socket. Make sure to

raise the lever up to a 90-

degree angle.

3.Look for the gold arrow on the

CPU. The gold arrow should

point as shown in the picture.

The CPU can only fit in the

correct orientation.

4.If the CPU is correctly installed,

the pins should be completely

embedded into the socket and

cannot be seen. Please note

that any violation of the correct

installation procedures may

cause permanent damages to

your mainboard.

5. Press the CPU down firmly into

the socket and close the lever.

As the CPU is likely to move

while the lever is being closed,

always close the lever with

your fingers pressing tightly on

top of the CPU to make sure

the CPU is properly and

completely embedded into the

socket.

Open Lever

90 degree

Sliding

Plate

Gold arrow

Correct CPU placement

Incorrect CPU placement

X

O

Close

Lever

Press down

the CPU

E-8

MS-7135 ATX Mainboard

Installing AMD Athlon64 CPU Cooler Set

When you are installing the CPU, make sure the CPU has a heat sink

and a cooling fan attached on the top to prevent overheating. If you do not

have the heat sink and cooling fan, contact your dealer to purchase and install

them before turning on the computer.

1.Detach the shield off the

backplate’s paster.

3.Turn over the mainboard again, and

place the mainboard on the flat

surface. Locate the two screw

holes of the mainboard.

4.Align the retention mechanism and

the backplate.

Fix the retention mechanism and

the backplate with two screws.

MSI Reminds You...

Mainboard photos shown in this section are for demonstration of the

cooler installation for Socket 754 CPUs only. The appearance of

your mainboard may vary depending on the model you purchase.

retention mechanism

2.Turn over the mainboard, and install

the backplate to the proper position.

E-9

Quick User’s Guide

6.Locate the Fix Lever, Safety Hook

and the Fixed Bolt. Lift up the

intensive fixed lever.

5.Position the cooling set onto the retention mechanism.

Hook one end of the clip to hook first, and then press down the other end of

the clip to fasten the cooling set on the top of the retention mechanism.

8.Make sure the safety hook com-

pletely clasps the fixed bolt of the

retention mechanism.

9.Attach the CPU Fan cable to the

CPU fan connector on the

mainboard.

7.Fasten down the lever.

MSI Reminds You...

While disconnecting the Safety Hook from the fixed bolt, it is neces-

sary to keep an eye on your fingers, because once the Safety Hook is

disconnected from the fixed bolt, the fixed lever will spring back instantly.

Safety Hook

Fixed Bolt

Fixed Lever

E-10

MS-7135 ATX Mainboard

Memory

The mainboard provides 2 slots for 184-pin DDR DIMM (Double In-Line Memory

Module) modules and supports the memory size up to 2GB. You can install DDR 333/

400 modules on the DDR DIMM slots (DIMM 1~2).

Memory Population Rules

Install at least one DIMM module on the slots. Each DIMM slot supports up to a

maximum size of 1GB. Users can install either single- or double-sided modules to

meet their own needs.

MSI Reminds You...

1. Make sure that you install memory modules of the same type and

density on DDR DIMMs.

2. For systems using double-sided DDR400 modules in single-chan-

nel mode, the maximum DRAM speed is DDR333.

Installing DDR Modules

1. The DDR DIMM has only one notch on the center of module. The module will only

fit in the right orientation.

2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in until

the golden finger on the memory module is deeply inserted in the socket.

3. The plastic clip at each side of the DIMM slot will automatically close.

Volt

Notch

Slot Memory Module Total Memory

DIMM 1 Single/Double Side 64MB~1GB

DIMM 2 Single/Double Side 64MB~1GB

Maximum System Memory Supported 64MB~2GB

MSI Reminds You...

You can barely see the golden finger if the module is properly

inserted into the socket.

E-11

Quick User’s Guide

Power Supply

The mainboard supports ATX power supply for the power system. Before

inserting the power supply connector, always make sure that all components are

installed properly to ensure that no damage will be caused.

PIN SIGNAL

13 +3.3V

14 -12V

15 GND

16 PS-ON#

17 GND

18 GND

19 GND

20 Res

21 +5V

22 +5V

23 +5V

24 GND

PIN SIGNAL

1 +3.3V

2 +3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 PWR OK

9 5VSB

10 +12V

11 +12V

12 NC

Pin Definition

PIN SIGNAL

1 GND

2 GND

3 12V

4 12V

JPW1 Pin Definition

ATX 24-Pin Power Connector: JWR1

This connector allows you to connect an ATX 24-pin power

supply. To connect the ATX 24-pin power supply, make sure the

plug of the power supply is inserted in the proper orientation

and the pins are aligned. Then push down the power supply

firmly into the connector.

You may use the 20-pin ATX power supply as you like. If

you’d like to use the 20-pin ATX power supply, please plug your

power supply along with pin 1 & pin 13 (refer to the image at the

right hand). There is also a foolproof design on pin 11, 12, 23 &

24 to avoid wrong installation.

MSI Reminds You...

1. These two connectors connect to the ATX power supply and have to

work together to ensure stable operation of the mainboard.

2. Power supply of 350 watts (and above) is highly recommended for

system stability.

3. ATX 12V power connection should be greater than 18A.

pin 12

pin 13

ATX 12V Power Connector: JPW1

This 12V power connector is used to provide power to the CPU.

JWR1

1

12 24

13

JPW1

1

3

4

2

E-12

MS-7135 ATX Mainboard

Important Notification about Power Issue

nVIDIA chipset is very sensitive to ESD (Electrostatic Discharge), therefore

this issue mostly happens while users intensively swap memory modules under S5

(power-off) states, and the power code is plugged while installing modules. Due to

several pins are very sensitive to ESD, so this kind of memory-replacement actions

might cause chipset system unable to boot. Please follow the following solution to

avoid this situation.

Unplug the AC power cable (shown in figure 1) or unplug the JWR1 & JPW1

power connectors (shown in figure 2 & figure 3) before the 1st installation or during

system upgrade procedure.

MSI Reminds You...

Mainboard photos shown in this section are for demonstration only.

The appearance of your mainboard may vary depending on the model

you purchase.

Figure 1:

Unplug the AC power cable

Figure 2:

Unplug the JWR1 power connector

Figure 3:

Unplug the JPW1 power connector

E-13

Quick User’s Guide

Back Panel

RJ-45 LAN Jack

8 1

Gigabit LAN (Optional)

PIN SIGNAL DESCRIPTION

1 D0P Differential Pair 0+

2 D0N Differential Pair 0-

3 D1P Differential Pair 1+

4 D2P Differential Pair 2+

5 D2N Differential Pair 2-

6 D1N Differential Pair 1-

7 D3P Differential Pair 3+

8 D3N Differential Pair 3-

10/100 LAN (Optional)

PIN SIGNAL DESCRIPTION

1 TDP Transmit Differential Pair

2 TDN Transmit Differential Pair

3 RDP Receive Differential Pair

4 NC Not Used

5 NC Not Used

6 RDN Receive Differential Pair

7 NC Not Used

8 NC Not Used

Serial Port

PIN SIGNAL

1 DCD

2 SIN

3 SOUT

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

1 2 3 4 5

6 7 8 9

USB Ports

1 2 3 4

PIN SIGNAL

1 VCC

2 -Data

3 +Data

4 GND

Mouse/Keyboard Connector

Pin1

Mouse/KBD

DATA

Pin2 NC

Pin3 GNDPin4 VCC

Pin5

Mouse/KBD Clock

Pin6 NC

Keyboard

USB Ports

L-Out

Mic

L-In

Mouse

Parallel

LAN

Serial Port

E-14

MS-7135 ATX Mainboard

Connectors

Floppy Disk Drive Connector: FDD1

The mainboard provides a standard floppy disk drive connector that supports

360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types.

FDD1

CD-In Connector: J1

This connector is provided for CD-ROM audio.

J1

GND

R

L

Serial ATA Connectors: SATA1~SATA4

SATA1~SATA4 are high-speed Serial ATA interface ports.

Each supports 1

st

generation serial ATA data rates of 150MB/s

and is fully compliant with Serial ATA 1.0 specifications. Each

Serial ATA connector can connect to 1 hard disk device.

GND

TXP

TXN

GND

RXN

RXP

GND

Connect to SATA1/2/3/4

Take out the dust cover and

connect to the hard disk

devices

Serial ATA cable

Chassis Intrusion Switch Connector: JCI1

This connector is connected to a 2-pin chassis switch. If

the chassis is opened, the switch will be short. The system will

record this status and show a warning message on the screen.

To clear the warning, you must enter the BIOS utility and clear the

record.

JCI1

2

1

GND

CINTRU

MSI Reminds You...

Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,

data loss may occur during transmission.

La page charge ...

MSI K8N Neo3 Le manuel du propriétaire

Ce manuel convient également à

MSI K8N Neo3 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents