Greenlee 555 Series Electric Benders, 555CX, 555DX Manuel utilisateur

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Register this product at www.greenlee.com

555

®

Series

Electric Benders

Shown with optional

1-1/2" to 2" rigid/EMT

combination shoe group

Patents Pending

Español ............... 29

Français .............. 57

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

All specications are nominal and may change as design

improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

555 is a registered trademark of Greenlee Tools, Inc.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Important Safety Information .....................................3–5

Grounding Instructions .................................................. 6

Specications ................................................................ 6

Identication ...............................................................7–9

Bending Attachment Groups ..................................10–11

Setup ......................................................................12–13

Operation ................................................................ 14–15

Illustrated Bending Glossary ....................................... 16

Bending Instructions ..............................................17–18

Additional Bending Instructions .............................19–21

Additional Bending Tables ......................................22–27

Transporting Bender .................................................... 28

Maintenance ................................................................ 28

Description

The Greenlee 555

®

Series Electric Benders are intended

to bend 1/2" to 2" conduit and pipe. Bending shoe

groups are available to accommodate the following

types of conduit and pipe:

• Electrical Metallic Tubing

• Intermediate Metallic Conduit

• Rigid Conduit

• PVC-Coated Rigid Conduit

• Schedule 40 Pipe

• Aluminum Rigid

• Stainless Steel

In addition to the 555

®

Series benders, this manual also

applies to the following models:

• 555CXRE/555DXRE (includes accessories for bending

Electrical Metallic Tubing, Rigid Conduit, and

Schedule 40 Pipe)

• 555CXRS/555DXRS (includes rigid single-shoe

accessories for bending Rigid Conduit and Schedule

40 Pipe)

• 555CXES/555DXES (includes EMT single-shoe

accessories for bending Electrical Metallic Tubing)

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction

manual and any markings on the tool provide

information for avoiding hazards and unsafe

practices related to the use of this tool. Observe

all of the safety information provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

Greenlee 555

®

Series Electric Benders.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning will

result in severe injury or death.

Do not use this tool in a hazardous

environment. Hazards include am-

mable liquids, gases, or other materi-

als. Using this tool in a hazardous

environment can result in a re or

explosion.

Failure to observe this warning will

result in severe injury or death.

Electric shock hazard:

• Connect the power cord to a

120 volt, 20 amp receptacle on a

ground fault protected circuit only.

Refer to “Grounding Instructions.”

• Do not modify the power cord or

plug.

• Inspect the power cord before

use. Repair or replace the cord if

damaged.

• Disconnect the unit from power

before servicing.

Failure to observe these warnings

could result in severe injury or death.

For continued protection against risk of re and

electric shock, replace ONLY with same manufacturer,

type, and rating of fuse. Refer to the “Maintenance”

section of this manual.

Failure to observe this warning could result in severe

injury or death.

• Do not use in dangerous environ-

ment. Do not use power tools in

damp or wet locations, or expose

them to rain. Keep work area well

lighted.

• Do not immerse the pendant switch

in water or any other liquid.

Failure to observe these warnings

could result in severe injury or death.

Always use safety glasses. Everyday

glasses only have impact resistant

lenses; they are NOT safety glasses.

When using in dusty environment, use

face or dust mask.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

IMPORTANT SAFETY INFORMATION

• Keep guards in place and in

working order.

• Remove any tools from bender

before operating. Form habit of

checking to see that all tools are

removed from bender before

turning it on.

Failure to observe these warnings

could result in severe injury or death.

Extension cords:

• Use only three-wire, 12 AWG exten-

sion cords that have three-prong

grounding-type plugs and three-

hole receptacles that accept the

tool’s plug.

• Do not use extension cords that are

longer than 30 m (100').

• Repair or replace damaged exten-

sion cords.

Failure to observe these warnings

could result in severe injury or death.

Make sure that the handle is properly installed and

secured with the safety spring clips and snap pins

before lifting or moving the bender. An improperly

installed handle could allow the bender to fall, injuring

nearby personnel.

Failure to observe this warning could result in severe

injury or death.

Pinch points:

• Keep hands away from bending

shoe, rollers, and conduit when

bender is in use.

• Support conduit when unloading.

Conduit can become loose and fall

if not properly supported.

Failure to observe these warnings

could result in severe injury or death.

• Reduce the risk of unintentional starting. Make sure

switch is in off position before plugging in.

• Never leave tool running unattended. Turn power

off. Do not leave tool until it comes to a complete

stop.

• Disconnect tools before servicing and when chang-

ing accessories such as shoes, rollers, and the like.

Accidental start-up could result in serious injury.

Failure to observe these warnings could result in

severe injury or death.

• Never stand on tool. Serious injury could occur if

the tool is tipped.

• Do not overreach. Keep proper footing and balance

at all times.

Failure to observe these warnings could result in

severe injury or death.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

IMPORTANT SAFETY INFORMATION

• Conduit moves rapidly as it is bent. The path of

the conduit must be clear of obstructions. Be sure

clearance is adequate before starting the bend.

• Wear proper apparel. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry

which may get caught in moving parts. Nonslip

footwear is recommended. Wear protective hair

covering to contain long hair.

• Do not force rollers or alter tool. It will do the

job better and safer at the rate for which it was

designed.

• Use right tool. Do not force tool or attachment to do

a job for which it was not designed.

• Use this tool for the manufacturer’s intended

purpose only. Use other than that which is

instructed in this manual can result in injury or

property damage.

Failure to observe these precautions may result in

injury or property damage.

• Keep work area clean. Cluttered areas and benches

invite accidents.

• Keep children away. All visitors should be kept safe

distance from work area.

• Make workshop kid proof with padlocks, master

switches, or by removing starter keys.

Failure to observe these precautions may result in

injury or property damage.

• Inspect the bender before use. Replace worn,

damaged, or missing parts with Greenlee replace-

ment parts. A damaged or improperly assem-

bled component could break and strike nearby

personnel.

• Maintain tools with care. Keep tool clean for best

and safest performance. Follow instructions for

lubricating and changing accessories.

• Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will

operate properly and perform its intended func-

tion. Check for alignment of moving parts, binding

of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation.

A guard or other part that is damaged should be

properly repaired or replaced.

• Use recommended accessories. Consult the

instruction manual for recommended accessories.

The use of improper accessories may cause risk of

injury to persons.

• Some bender parts and accessories are heavy

and may require more than one person to lift and

assemble.

Failure to observe these precautions may result in

injury or property damage.

Note: Keep all decals clean and legible, and replace

when necessary.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

Grounding Instructions

Electric shock hazard:

• Do not modify the plug provided

with the tool.

• Connect this tool to a grounded

receptacle on a 20 amp ground

fault protected circuit.

Failure to observe these warnings

could result in severe injury or death.

This tool must be grounded. In the event of a malfunc-

tion or breakdown, an electrical ground provides a path

of least resistance for the electric current. This path of

least resistance is intended to reduce the risk of electric

shock.

This tool’s electric cord has a grounding conductor and

a grounding plug as shown. Do not modify the plug.

Connect the plug to a corresponding GFCI-protected

receptacle that is properly installed and grounded

in accordance with all national and local codes and

ordinances.

Do not use an adapter.

NEMA 5-20

Plug Receptacle

Do not modify the plug provided. If it will not t the

outlet, have the proper outlet installed by a qualied

electrician. Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. The conductor with insulation having an outer

surface that is green with or without yellow stripes

is the equipment-grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor

to a live terminal. Check with a qualied electrician or

service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the

tool is properly grounded.

Speciﬁcations

Height ..................................................................................................100.1 cm (39.4")

Width ........................................................................................................68 cm (26.8")

Depth .....................................................................................................58.4 cm (23.0")

Mass/Weight (bender without shoes or roller supports ..........................124 kg (273 lb)

Power Supply .................................................................................... 120 VAC, 20 amp

GFCI-protected receptacle

Operating Conditions

Temperature .......................................................... –20 °C to 49 °C (–5 °F to 120 °F)

Relative Humidity ....................................................................................0% to 98%

Capacity .............................................................. 1/2" to 2" conduit, schedule 40 pipe

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Features

1. Handle

2. Lifting bar

3. Shoe retainer

4. Roller engagement arm

5. Roller retainer

6. Pendant receptacle

7. Main power (On-Off) switch/circuit breaker

8. Roller adapter

9. Absolute encoder (555DX only)

10. Kick bar

11. Power cord with tie strap

12. Motor

13. Gearbox

14. Motor debris guard

15. Instruction manual storage compartment

16. Fuse holder

F

G

15

D

E

I

7

16

5

6

2

B

C

3

9

A

4

8

12

11

14

13

10

H

1

Identiﬁcation

555

®

SERIES ELECTRIC BENDER

Decals

A. Engage rollers

B. Protractor

C. Bending

D. Instruction

E. Warning

F. Lifting

G. Identication

H. Squeeze

I. Bending tables

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

Identiﬁcation

BENDING ACCESSORIES

17. 1/2" to 1-1/4" support roller

13854 for combination shoe (1/2"–1-1/4" shoe)

02549 for rigid/IMC single shoe (1/2"–2" shoe)

02567 for EMT single shoe (1/2"–2" shoe)

02554 for PVC-coated rigid single shoe (1/2"–2" shoe)

18. 1-1/2" to 2" support roller

13853 for combination shoe (1-1/2"–2" shoe)

02549 for rigid/IMC single shoe (1/2"–2" shoe)

02567 for EMT single shoe (1/2"–2" shoe)

02554 for PVC-coated rigid single shoe (1/2"–2" shoe)

20

17

19

18

20

19

17, 18

Rigid, EMT Combination

Shoe Group

19. 1-1/2" to 2" EMT squeeze rollers

02552 for combination shoe (1-1/2"–2" shoe)

02552 for EMT single shoe (1/2"–2" shoe)

20. 1-1/2" to 2" IMC squeeze rollers

13856 for combination shoe (1-1/2"–2" shoe)

13856 for rigid/IMC single shoe (1/2"–2" shoe)

Single-Shoe Group

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

Identiﬁcation

BENDING ACCESSORIES

13930 EMT Shoe Group

IMC Single-Groove Shoes

21. 1/2" to 1-1/4" support roller

17986 for EMT only shoe (1/2"–1-1/4" shoe)

00936 for rigid/IMC only shoe (1/2"–1-1/4" shoe)

00946 for PVC-coated rigid shoe (1/2"–1-1/4" shoe)

22. 1-1/2" to 2" support roller

17984 for rigid only shoe (1-1/2"–2" shoe)

13861 for PVC-coated rigid shoe (1/2"–2" shoe)

23. 1-1/2" to 2" EMT squeeze rollers

13851 for EMT, single-groove type shoes

24. 1-1/2" to 2" IMC squeeze rollers

13852 for IMC, single-groove type shoes

25. 1-1/2" and 2" tail rollers

13862 for EMT and IMC single-groove shoes

(use with squeeze rollers)

24

25

23

25

21

22

Rigid Shoe Group

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

Bending Attachment Groups

RIGID SINGLE SHOE

EMT SINGLE SHOE

28008: 1/2" to 2" Rigid

1/2" to 1-1/4" IMC

1/2" to 2" Schedule 40 Pipe

UPC No.

Key 78-3310- Description

1 02548 Bending shoe for 1/2" to 2"

2 02549 Roller support unit for 1/2" to 2"

23818 Storage box

13934: 1/2" to 2" EMT

UPC No.

Key 78-3310- Description

1 02543 Bending shoe for 1/2" to 2"

2 02567 Roller support unit for 1/2" to 2"

3 02552 Squeeze roller unit for 1-1/2" and 2"

23818 Storage box

1

2

1

2

3

RIGID/IMC SINGLE SHOE

13856: 1-1/2" and 2" IMC

UPC No.

Key 78-3310- Description

1 13856 Squeeze roller assembly

Note: 28008 rigid shoe group or 12580 combination shoe

group is required to use the IMC squeeze roller.

1

Shoe and tail

support roller

not included

PVC-COATED RIGID SINGLE SHOE

12586: 1/2" to 2" 40 Mil PVC-Coated Rigid

UPC No.

Key 78-3310- Description

1 02553 Bending shoe for 1/2" to 2"

2 02554 Roller support unit for 1/2" to 2"

23818 Storage box

1

2

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

Bending Attachment Groups (cont’d)

RIGID, EMT COMBINATION SHOE

12580: 1/2" to 2" Rigid, EMT

UPC No.

Key 78-3310- Description

1 13858 1/2" through 1-1/4" rigid, EMT, IMC bending shoe

2 13854 1/2" through 1-1/4" rigid, EMT, IMC support roller

3 13859 1-1/2" and 2" rigid, EMT, IMC bending shoe

4 13853 1-1/2" and 2" rigid support roller; EMT, IMC tail support roller

5 02552 1-1/2" and 2" EMT squeeze roller support

38718 Storage chest

Note: Optional 13856 squeeze roller support is required for bending

1-1/2" and 2" IMC conduit.

1

2

4

5

3

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Setup

Always use safety glasses. Everyday

glasses only have impact resistant

lenses; they are NOT safety glasses.

When using in dusty environment, use

face or dust mask.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Disconnect tools before servicing and when chang-

ing accessories such as shoes, rollers, and the like.

Accidental start-up could result in serious injury.

Refer to the “Identication” section of this manual.

1. Slide the appropriate bending shoe onto the main

spindle. Orient the shoe so that the EMT hook

(silver) is about 90° clockwise from the sprocket

spoke with two drive lug holes.

2. Align the drive studs in the shoe with the holes in

the sprocket. Secure with the shoe retainer (3).

3. Mount the roller adapter (8).

4. Mount the appropriate roller support:

a. For 1-1/2" and 2" rigid with combination shoe,

use the roller adapter and rigid rollers.

10

8

b. For 1-1/2" and 2" rigid with single shoe, use

the roller adapter and rigid rollers.

10

8

Green

Color

Note: 1/2"–1-1/4" rollers

shown in lowered/disengaged

position.

c. For 1-1/2" and 2" EMT with combination

shoe, use the rigid support rollers and EMT

squeeze rollers.

10

8

11

Silver

Color

d. For 1-1/2" and 2" EMT with single shoe,

use the EMT support rollers and EMT squeeze

rollers.

10

8

Silver

Color

11

Note: 1/2"–1-1/4" rollers

shown in lowered/disengaged

position.

e. For 1-1/2" and 2" EMT with single-groove

shoe, use the tail rollers and EMT squeeze

rollers. Keep the squeeze roller size to be used

toward the bender.

13

8

11

Black

Color

f. For 1-1/2" and 2" IMC with combination shoe,

use the rigid support rollers and IMC squeeze

rollers.

10

8

12

Green

Color

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

13

Setup (cont’d)

g. For 1-1/2" and 2" IMC with single shoe, use

the rigid/IMC support rollers and IMC squeeze

rollers.

10

8

12

Note: 1/2"–1-1/4" rollers

shown in lowered/disengaged

position.

Green

Color

h. For 1-1/2" and 2" IMC with single-groove

shoe, use the tail rollers and IMC squeeze

rollers. Keep the squeeze roller size to be used

toward the bender.

13

8

12

Black

Color

j. For 1/2" to 1-1/4" rigid, EMT, and IMC with

combination shoe, use the roller adapter and

support roller.

9

8

Flat Top

Edge

k. For 1/2" to 1-1/4" rigid and IMC with single

shoe, use rigid/IMC support rollers.

9

8

Green Color

Round Top Edge

m. For 1/2" to 1-1/4" EMT with single shoe, use

the EMT support rollers.

9

8

Silver Color

Round Top Edge

For 1-1/2" to 2" EMT and IMC

5. Slide the roller engagement arm (4) over the main

roller spindle and secure with the roller retainer (5).

6. Mark the conduit according to bend layout

instructions.

7. Place the bender in the desired vertical or horizontal

position.

Zeroing 555DX

1. Use BEND or UNLOAD on the pendant to align the

shoe groove with zero on the bender decal.

2. Press and hold the

button while pressing JOG.

To place bender in horizontal position

1. Ensure handle (1) is on bender and pinned in place.

2. Stand in back of the bender, grasp the handle, place

one foot on the kick bar (14), and pull back on the

handle.

3. Gently lower the bender into position.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

14

Operation

Always use safety glasses. Everyday

glasses only have impact resistant

lenses; they are NOT safety glasses.

When using in dusty environment, use

face or dust mask.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Pinch points:

• Keep hands away from bending

shoe, rollers, and conduit when

bender is in use.

• Support conduit when unloading.

Conduit can become loose and fall

if not properly supported.

Failure to observe these warnings

could result in severe injury or death.

Wear proper apparel. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry

which may get caught in moving parts. Nonslip foot-

wear is recommended. Wear protective hair covering

to contain long hair.

Failure to observe this precaution could result in

severe injury or death.

Bending Conduit

Refer to the “Identication” section of this manual.

1. Plug the bender into a grounded 20 amp outlet.

2. Plug the pendant switch into the pendant receptacle

(6).

3. Turn on the main power switch (7).

4. Verify the shoe orientation.

For the 555DX only: If the pendant

display shows approximately the same

degree as the pointer on the shoe,

the shoe position is correct. If not,

rotate the shoe’s engagement points

in the sprocket 90° by hand or zero

the pendant display. The shoe units in

the 12580 and 12581 bending groups

have drive studs that will align in only one position

with the holes in the sprocket. Re-zero the pendant

display to align the desired shoe pointer with zero

on the bender decal.

5. Press BEND or UNLOAD on the pendant until

the shoe is 5° to 10° before the starting point (0°)

(approx. –5° on 555DX pendant).

6. Load the conduit so that the bending mark is

aligned with the front edge of the hook.

7. Determine the angle to stop at to achieve the

desired bend angle from the bending decal or tables

in this manual.

8. Bend the conduit.

a. For 1-1/2" and 2" EMT or IMC conduit, use the

roller engagement arm (4) to raise the squeeze

rollers and position them so that both rollers

make contact with the conduit. Note that the

engagement arm can be placed in either of two

positions to facilitate hand or foot actuation.

Press BEND while applying pressure to the

engagement arm until the rollers hit their stop.

Roller

Engagement

Arm

b. For all other conduit, press BEND while making

sure the bend mark stays at the front of the hook

until the conduit contacts the tail roller.

9. Continue to press BEND until reaching the desired

bend angle.

• On the 555DX pendant, use JOG to sneak up on

an angle. JOG will advance the shoe about 1/2°.

• On both the 555CX and 555DX pendant, use

BEND to sneak up on an angle.

Note: The angles displayed on the bending decal

and the pendant may not always be in sync due

to shoe casting variations, although they will be

consistent.

10. Press UNLOAD to free the conduit.

11. Twist the conduit to release it from the hook and

remove it from the shoe.

U

N

L

O

A

D

B

E

N

D

555CX 555DX

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

15

Operation (cont’d)

Squeeze Adjustment

Squeeze is factory set and should not normally need to

be adjusted.

When bending 1-1/2" or 2" EMT or IMC, the amount

of squeeze applied to the conduit can be adjusted to

compensate for conduit variations. The squeeze is set

properly if the conduit does not contact the roller on

the tail roller support (10) while bending EMT. Also, the

conduit should not be more than approximately 1/4"

(6mm) above the tail roller.

1/4" (6 mm) max.

To adjust the squeeze:

1. Unplug the bender.

2. Remove screw (refer to gure below).

3. Rotate the squeeze adjuster:

• If the conduit is contacting the tail roller, increase

the squeeze by rotating the squeeze adjuster

clockwise.

• If the conduit is more than 1/4" (6 mm) above

the roller, decrease the squeeze by rotating the

squeeze adjuster counterclockwise.

INCREASE

DECREASE

Squeeze Adjuster

Holding Screw

Arrow Adjustment

The arrows on the single shoes can be adjusted to

compensate for variations in conduit.

1. Load the conduit into the proper shoe groove.

2. Press BEND momentarily until the shoe rotates

enough so that the conduit is snug in the hook.

3. Verify that the arrow position is aligned with 0° on

the front protractor scale. If necessary, loosen the

hex head screw and adjust the arrow to align with

0°. Retighten the hex head screw, as shown.

Loosen hex

screw to

adjust arrow.

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

16

Illustrated Bending Glossary

back-to-back bend — any U-shaped bend formed by two

parallel 90° bends with a straight section of conduit or pipe

between the bends.

center-to-center distance — the distance between the

successive bends that make up an offset or a three-bend

saddle.

developed length — the actual length of pipe that will be

bent; refer to distance “d” in the illustration at left.

gain — the difference between the straight-line distance

(a + a) and the shorter radial distance, (d) where:

q = angle of bend

r = the centerline bending radius of the bending shoe

kick — single bend of less than 90°

leg length — the distance from the end of a straight section

of conduit or pipe to the bend; measured from the end to the

outside edge of the conduit or pipe.

offset bend — two opposite bends with the same degree of

bend; used to avoid an obstruction.

offset height — the distance between the two legs of

an offset bend, measured perpendicular to the two legs; also

called amount of offset and depth of offset.

rise — the distance from the end of a straight section of

conduit or pipe to the bend; measured from the end to the

center line of the conduit or pipe. Also called stub or

stub-up.

saddle — a three-bend or four-bend combination; used

to avoid an obstruction.

shrink — the amount of conduit “lost” when laying out an

offset bend working toward an obstruction.

springback — the amount, measured in degrees, that a

conduit or pipe tends to straighten after being bent.

a

d

r

Offset Height

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

17

Bending Instructions

90° STUBS

1. Measure the length of the required stub.

2. Refer to the Minimum Stub Length formula on the

Deduct Table. The required stub must be equal to or

longer than the Minimum Stub Length.

3. Measure and mark the stub length on the conduit.

This is Mark 1. Subtract the Deduct from this mark

and make a new mark. This is Mark 2.

4. Align Mark 2 with the front edge of the hook and

bend the conduit.

Notes:

When the operator presses UNLOAD, the conduit may

spring back a few degrees. Compensate by overbending

as shown in the Scale Reading Tables.

The rigid shoe can make a 180° bend in one shot. All

other shoes bend to 90° maximum.

Deduct Table

CONDUIT SIZE 1/2 3/4 1 1-1/4 1-1/2 2

DEDUCT

COMBO SHOE

RIGID/IMC

7-1/2 9 11 13-5/8 14-7/8 16-1/8

COMBO SHOE

EMT

7-1/2 9 11 13-5/8 14-7/8 16-3/8

RIGID ONLY

SHOE

7-1/2 9 11 14 14-1/4 16-1/8

MINIMUM STUB LENGTH = DEDUCT PLUS 2 INCHES

Figures are approximate

STUB LENGTH

DEDUCT

MARK 2

MARK 1

STUB LENGTH

Scale Reading Table—Single-Shoe Groups

Figures are approximate.

Note: Due to varying conduit material

properties, 1-1/2" or 2" aluminum

rigid may require IMC squeeze

rollers for bending. If ﬂattening

occurs, reduce the squeeze setting

two positions and use IMC bending

procedures.

CONDUIT

SIZE

RIGID EMT IMC PVC-COATED RIGID

15° 30° 45° 60° 90° 15° 30° 45° 60° 90° 15° 30° 45° 60° 90° 15° 30° 45° 60° 90°

1/2 17 33 49 64 96 16 32 48 63 95 20 36 51 67 98 16 31 47 62 93

3/4 17 33 48 64 95 17 33 48 64 95 19 35 50 66 97 15 31 46 62 93

1 17 32 48 63 94 17 32 48 63 94 19 35 50 66 97 16 32 47 63 94

1-1/4 17 32 48 63 94 17 32 48 63 94 19 35 50 66 97 15 30 46 61 92

1-1/2 17 32 48 63 94 19 35 50 66 97 17 33 49 64 96 18 33 49 64 95

2 17 32 48 63 94 19 34 50 65 96 19 34 50 65 96 19 34 50 65 96

Scale Reading Table—Combo Shoe Group

Figures are approximate.

Note: Due to varying conduit material

properties, 1-1/2" or 2" aluminum

rigid may require IMC squeeze

rollers for bending. If ﬂattening

occurs, reduce the squeeze setting

two positions and use IMC bending

procedures.

CONDUIT

SIZE

RIGID EMT IMC

15° 30° 45° 60° 90° 15° 30° 45° 60° 90° 15° 30° 45° 60° 90°

1/2 17 33 49 64 96 16 32 48 63 95 20 36 51 67 98

3/4 17 33 48 64 95 17 33 48 64 95 19 35 50 66 97

1 17 32 48 63 94 17 33 48 64 95 19 35 50 66 97

1-1/4 17 33 48 64 95 17 33 49 64 96 19 35 50 66 97

1-1/2 17 32 48 63 94 16 31 47 62 93 17 33 49 64 96

2 17 32 48 63 94 16 31 47 62 93 19 34 50 65 96

Scale Reading Table

Figures are approximate.

CONDUIT

SIZE

RIGID EMT IMC PVC-COATED RIGID

15° 30° 45° 60° 90° 15° 30° 45° 60° 90° 15° 30° 45° 60° 90° 15° 30° 45° 60° 90°

1/2 18 35 50 66 96 16 32 48 63 95 20 36 51 67 98 16 31 47 62 93

3/4 17 32 47 63 95 17 32 47 62 95 20 36 51 67 97 15 31 46 62 93

1 17 33 48 65 95 17 32 47 62 95 21 36 51 66 97 16 32 47 63 94

1-1/4 18 33 48 63 95 17 32 47 62 95 18 33 50 65 96 16 31 47 62 93

1-1/2 19 34 49 65 95 17 32 47 61 94 19 34 49 65 95 18 33 49 64 95

2 18 34 49 65 95 17 32 47 62 95 20 35 50 66 96 19 34 50 65 96

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

18

Offsets

1. Measure the height and length of the obstruction.

Select the angle to be used.

2. Refer to the Offset Table. The height of the obstruc-

tion must be equal to or greater than the minimum

offset.

3. Refer to the X Table to nd the X dimension. Refer

to the Offset Table to nd the center-to-center

distance.

Note: If the center-to-center distance is not shown,

calculate it by using the multipliers shown in the

Offset Table.

4. Mark the conduit as shown.

5. Insert the conduit into the bender. Align Mark 1 with

the front edge of the hook and bend the conduit.

6. Align Mark 2 with the front edge of the hook.

Without removing the conduit from the bender,

rotate the conduit 180°. Make the second bend.

LENGTH

HEIGHT

LENGTH

MARK 1 MARK 2

CENTER TO CENTER

DISTANCE

X

OBSTRUCTION

Offset Table

OFFSET }

2 4 6 8 10

15°

Max. Conduit

Size

3/4 1-1/2 2

Center-to-Center 7-3/4 15-7/16 23-3/16 30-15/16 38-5/8

30°

Max. Conduit

Size

3/4 1 1-1/2 2

Center-to-Center 8 12 16 20

45°

Max. Conduit

Size

1/2 1 1-1/4

Center-to-Center 8-1/2 11-5/16 14-1/8

OFFSET }

12 14 16 18 20 22

15°

Max. Conduit

Size

2

Center-to-Center 46-3/8 54-1/16 61-13/16 69-9/16 77-1/4 85

30°

Max. Conduit

Size

2

Center-to-Center 24 28 32 36 40 44

45°

Max. Conduit

Size

1-1/2 2

Center-to-Center 16-15/16 19-13/16 22-5/8 25-7/16 28-1/4 31-1/8

CENTER-TO-CENTER DISTANCE = OFFSET HEIGHT x MULTIPLIER

OFFSET

ANGLE

10° 15° 22-1/2° 30° 45°

MULTIPLIER 5.8 3.9 2.6 2.0 1.4

Figures are approximate

X Table

CONDUIT SIZE 1/2 3/4 1 1-1/4 1-1/2 2

“X” 3-1/16 3-1/16 3-3/16 4 4-1/4 4-1/2

Figures are approximate

Bending Instructions (cont’d)

Centerline Bending Radii—

Rigid and EMT Shoe Groups (180° Bending Shoes)

SHOE

SIZE

EMT RIGID IMC

in mm in mm in mm

1/2 4-1/4 108 4-1/4 108 4-1/4 108

3/4 5-3/8 136.5 5-7/16 138 5-7/16 138

1 6-3/4 171.5 6-5/16 160 6-5/16 160

1-1/4 8-3/4 222 8-3/4 222 8-3/4 222

1-1/2 8-9/32 210 8-1/4 209 8-9/32 210

2 9-3/16 233 9-1/2 241 9-3/16 233

Centerline Bending Radii—

Combo Shoe Group and Single-Shoe Groups

SHOE SIZE

EMT IMC/RIGID

in mm in mm

1/2 4-5/16 109.5 4-1/4 108

3/4 5-1/2 139.7 5-7/16 138.1

1 7 177.8 6-15/16 176.2

1-1/4 8-13/16 223.8 8-3/4 222.3

1-1/2 8-3/8 212.7 8-1/4 209.6

2 9-1/4 235.0 9 228.6

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

19

The following drawings and bending tables are intended

to provide the information necessary to accomplish

the most common types of bends. The bending tables

contain conduit marking information.

STUBS

1. Select the size and type of conduit. Determine the

height of stub and the angle to be used.

2. Find the table that corresponds to the size and type

of conduit selected in Step 1.

3. Under the column labeled ANGLE, nd the appro-

priate angle.

4. Find the row labeled Y. In the row at the top of the

page, nd the height (H) of the stub. The number

shown at the intersection of row Y and column H

is the distance Y. Place the bending mark Y inches

from the end of the conduit.

5. Bend the conduit.

Y

HEIGHT

MARK

ANGLE

Additional Bending Instructions

OFFSETS

An offset is used to route the conduit around an

obstruction. To make an offset, two equal bends are

required. The distance between the two bends is the

center-to-center distance.

When working past an obstruction, it is necessary to

determine the location of the rst bend. The center-to-

center distance is then used to determine the location of

the second bend. When working toward an obstruction,

it is necessary to determine the location of the second

bend. The center-to-center distance is then used to

determine the location of the rst bend.

Working Past an Obstruction

1. Select the size and type of conduit. Measure the

height of the obstruction and the distance labeled

LENGTH. Determine the angle to be used.

2. Find the table that corresponds to the size and type

of conduit selected in Step 1.

3. To the right of the size and type of conduit, nd the

dimension labeled X. Subtract X from LENGTH.

Place the rst bending mark this distance from the

end of the conduit.

4. Under the column labeled ANGLE, nd the appro-

priate angle. Find the row labeled L1. In the row at

the top of the page, nd the height (H) of the offset.

The number shown at the intersection of row L1 and

column H is L1. Place the second bending mark L1

inches from the rst bending mark.

5. Bend the conduit.

L1LENGTH – X

LENGTH

HEIGHT

START OF

FIRST

BEND

MARK 1 MARK 2

ANGLE

OBSTRUCTION

555

®

Series Electric Benders

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

20

Additional Bending Instructions (cont’d)

Working Toward an Obstruction

1. Select the size and type of conduit. Measure the

height of the obstruction and the distance labeled

LENGTH TO END OF SECOND BEND. Determine

the angle to be used.

2. Find the table that corresponds to the size and type

of conduit selected in Step 1.

3. Under the column labeled ANGLE, nd the appro-

priate angle. Find the row labeled Z. In the row at

the top of the page, nd the height (H) of the offset.

The number shown at the intersection of the Z row

and the H column is Z. Subtract Z from LENGTH

TO THE END OF SECOND BEND. Place the rst

bending mark this distance from the end of the

conduit.

4. In the same column, nd the row labeled L1. Place

the second bending mark L1 inches from the rst

bending mark.

5. Bend the conduit.

L1LENGTH – Z

LENGTH TO END OF SECOND BEND

HEIGHT

MARK 1 MARK 2

ANGLE

THREE-BEND SADDLE

1. Select the size and type of conduit. Measure the

height of the obstruction and the distance from

the end of the conduit to the center (LENGTH TO

CENTER) of the bend. Determine the angle to be

used.

2. Find the table that corresponds to the size and type

of conduit selected in Step 1.

3. Under the column labeled ANGLE, nd the appro-

priate angle. Find the row labeled Z. In the row at

the top of the page, nd the height (H) of the offset.

The number shown at the intersection of the Z row

and the appropriate H column is Z. Subtract Z from

the LENGTH TO CENTER. Place the rst bending

mark this distance from the end of the conduit.

4. In the same column, nd the row labeled L1. Place

the second bending mark L1 inches from the rst

bending mark.

5. In the same column, nd the row labeled L2. Place

the third bending mark L2 inches from the second

bending mark.

6. Bend the conduit.

L1LENGTH – Z

LENGTH TO CENTER

MARK 1

MARK 2

MARK 3

L2

ANGLE

HEIGHT

La page charge ...

Greenlee 555 Series Electric Benders, 555CX, 555DX Manuel utilisateur

Greenlee 555 Series Electric Benders, 555CX, 555DX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents