Yamaha 02R96 Le manuel du propriétaire

E

DIGITAL MIXING CONSOLE

Owner’s ManualOwner’s Manual

Owner’s Manual

Keep This Manual For Future Reference.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on

different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

NEDERLAND THE NETHERLANDS

● Dit apparaat bevat een lithium batterij voor geheugen

back-up.

● Raadpleeg uw leverancier over de verwijdering van de

batterij op het moment dat u het apparaat ann het einde

van de levensduur afdankt of de volgende Yamaha Service

Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

● Gooi de batterij niet weg, maar lever hem in als KCA.

● This apparatus contains a lithium battery for memory

back-up.

● For the removal of the battery at the moment of the

disposal at the end of the service life please consult your

retailer or Yamaha Service Center as follows:

Yamaha Music Nederland Service Center

Address: Kanaalweg 18-G, 3526 KL

UTRECHT

Tel: 030-2828425

● Do not throw away the battery. Instead, hand it in as small

chemical waste.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig

håndtering. Udskiftning må kun ske med batteri

af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd

samma batterityp eller en ekvivalent typ som

rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti

asennettu. Vaihda paristo ainoastaan

laitevalmistajan suosittelemaan tyyppiin. Hävitä

käytetty paristo valmistajan ohjeiden

mukaisesti.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The above warning is located on the

side of the unit.

i

02R96—Owner’s Manual

Important Information

Warnings

• Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Man-

ual or as marked on the unit. Failure to do so is a ﬁre and electrical shock hazard.

• Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock

may result.

• Do not place heavy objects, including this unit, on top of the power cord. A damaged power

cord is a ﬁre and electrical shock hazard. In particular, be careful not to place heavy objects

on a power cord covered by a carpet.

• Do not place a container with liquid or small metal objects on top of this unit. Liquid or

metal objects inside this unit are a ﬁre and electrical shock hazard.

• This unit is equipped with a dedicated ground connection to prevent electrical shock.

Before connecting the power plug to an AC outlet, be sure to ground the unit. If the power

cord has a three-pin plug, it will provide sufﬁcient grounding so long as the AC outlet is

grounded correctly.

• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a ﬁre

and electrical shock hazard.

• Do not remove the unit’s cover. You could receive an electrical shock. If you think internal

inspection, maintenance, or repair is necessary, contact your dealer.

• Do not modify the unit. Doing so is a ﬁre and electrical shock hazard.

• If lightning begins to occur, turn off the power switch of the unit as soon as possible, and

unplug the power cable plug from the electrical outlet.

• If there is a possibility of lightning, do not touch the power cable plug if it is still connected.

Doing so may be an electrical shock hazard.

• Use only the included power cord for this unit. Using other types may be a ﬁre and electrical

shock hazard.

• The 02R96 has four rear-panel slots for installing mini-YGDAI cards. For technical reasons,

certain card combinations are not supported. Before installing any cards, check the Yamaha

web site to if your card is compatible. Installing cards that are not endorsed by Yamaha may

cause electrical shock, ﬁre, or damage to the unit.

• If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a

replacement. Using the unit with a damaged power cord is a ﬁre and electrical shock hazard.

• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid

gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet.

Consult your dealer for repair. Using the unit in this condition is a ﬁre and electrical shock

hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove

the power plug from the AC outlet, and contact your dealer. If you continue using the unit

without heeding this instruction, ﬁre or electrical shock may result.

Cautions

• Keep this unit away from the following locations:

— Locations exposed to oil splashes or steam, such as near cooking stoves, humidiﬁers, etc.

— Unstable surfaces, such as a wobbly table or slope.

— Locations exposed to excessive heat, such as inside a car with all the windows closed, or

places that receive direct sunlight.

— Locations subject to excessive humidity or dust accumulation.

• Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A

damaged power cord is a potential ﬁre and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

ii

02R96—Owner’s Manual

• This unit has ventilation holes along the front underside and at the rear to prevent the inter-

nal temperature from rising too high. Do not block them. Blocked ventilation holes are a

ﬁre hazard. In particular, do not operate the unit while it’s on its side, is upside down, or

while it’s covered with a cloth or dust sheet.

• If you are using the optional MB02R96 Peak Meter Bridge, do not hold only the MB02R96

when moving the 02R96. Otherwise, the meter brackets may be damaged, the main unit

may malfunction, or you may be injured if the unit falls.

• This unit is heavy. Use two or more people to carry it.

• When you transport or move the 02R96 with the MB02R96 attached, do not permit impact

or stress on the cable connector that connects the MB02R96 to the 02R96. Otherwise, mal-

function may occur.

• To relocate the unit, turn the power switch off, remove the power plug from the AC outlet,

and remove all connecting cables. Damaged cables may cause ﬁre or electrical shock.

• If you know you will not use this unit for a long period of time, such as when going on vaca-

tion, remove the power plug from the AC outlet. Leaving it connected is a potential ﬁre haz-

ard.

• The inside of the unit should be cleaned periodically. Dust accumulation inside the unit

may cause malfunction and is a potential ﬁre hazard. Consult your dealer for information

about cleaning.

• To prevent electrical shock when cleaning the unit, remove the power plug from the AC out-

let.

Operating Notes

• XLR-type connectors are wired as follows: pin 1–ground, pin 2–hot (+), and pin 3–cold (–).

• Insert TRS phone jacks are wired as follows: sleeve–ground, tip–send, and ring–return.

• The performance of components with moving contacts, such switches, rotary controls, fad-

ers, and connectors, deteriorates over time. The rate of deterioration depends on the oper-

ating environment and is unavoidable. Consult your dealer about replacing defective

components.

• Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone

away from the unit.

• If the message “WARNING Low Battery!” appears when you turn on this unit, contact your

dealer as soon as possible about replacing the internal data backup battery. The unit will still

operate correctly, but data other than the presets will be lost.

• Before replacing the batteries, back up your data to a memory card, or another unit by using

MIDI Bulk Dump.

• The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise

occurs, relocate the affected equipment.

• When connecting D-sub cables, be sure to tighten the screws on both sides of the connector

securely. To disconnect the cable, loosen the screws completely, then remove the cable by

holding the connector part. Do not remove the plug by pulling the cable while the screws

are still attached. Otherwise, the connector may be damaged, leading to malfunction.

• When you change the wordclock settings on any device in your digital audio system, some

devices may output noise, so turn down your power amps beforehand, otherwise your

speakers may be damaged.

Interference

The 02R96 uses high-frequency digital circuits that may cause interference on radio and

television equipment located nearby. If interference is a problem, relocate the affected

equipment. Using a mobile telephone near the unit may induce noise. In this case use the

telephone away from the unit.

iii

02R96—Owner’s Manual

02R96 Exclusion of Certain Responsibility

Manufacturer, importer, or dealer shall not be liable for any incidental damages including

personal injury or any other damages caused by improper use or operation of the 02R96.

Trademarks

ADAT MultiChannel Optical Digital Interface is a trademark and ADAT and Alesis are reg-

istered trademarks of Alesis Corporation. Apogee is a trademark of Apogee Electronics, Inc.

Apple, Mac, and Power Macintosh are registered trademarks and Mac OS is a trademark of

Apple Corporation, Inc. HUI is a trademark of Mackie Designs, Inc. Intel and Pentium are

registered trademarks of Intel Corporation. Nuendo is a registered trademark of Steinberg

Media Technologies AG. Pro Tools is a trademark or registered trademark of Digidesign

and/or Avid Technology, Inc. Tascam Digital Interface is a trademark and Tascam and Teac

are registered trademarks of Teac Corporation. Microsoft and Windows are registered

trademarks of Microsoft Corporation, Inc. Waves is a trademark of Waves, Inc. Yamaha is a

trademark of Yamaha Corporation. All other trademarks are the property of their respective

holders and are hereby acknowledged.

Copyright

No part of the 02R96, its software, or this

Owner’s Manual

may be reproduced or distrib-

uted in any form or by any means without the prior written authorization of Yamaha Cor-

poration.

Yamaha Web Site

Further information about the 02R96, related products, and other Yamaha professional

audio equipment is available on the Yamaha Professional Audio Web site at:

<http://www.yamaha.co.jp/product/proaudio/homeenglish/>.

Package Contents

• 02R96 Digital Mixing Console

• CD-ROM

•Power cord

• This manual

Optional Extras

• MB02R96 Peak Meter Bridge

• SP02R96 Wooden Side Panels

• mini YGDAI I/O cards

About this Owner’s Manual

This

Owner’s Manual

covers the 02R96 Digital Mixing Console.

All the information you need in order to operate the 02R96 Digital Mixing Console is con-

tained in this manual. Use the table of contents to familiarize yourself with the manual’s

organization and to locate tasks and topics, and use the index to locate speciﬁc information.

Before diving in, it’s recommend that you read the “Operating Basics” chapter, starting on

page 29.

Each chapter of this manual discusses a speciﬁc section or function of the 02R96. The Input

and Output Channels are explained in the following chapters: “Input Channels,” “Bus

Outs,” “Aux Sends,” and “Stereo Out.” Where possible, these chapters have been organized

in order of signal ﬂow, from input through to output.

Functions such as EQ and Delay are common to all channels. Rather than repeat the same

information over and over, these functions are explained once in the “Common Channel

Functions” chapter, which starts on page 87. The Input Channels, Bus Outs, Aux Sends, and

iv

02R96—Owner’s Manual

Stereo Out chapters contain cross-references to the relevant sections of the “Common

Channel Functions” chapter.

Conventions Used in this Manual

The 02R96 features two types of button: physical buttons that you can press (e.g., ENTER

and DISPLAY) and buttons that appear on the display pages. References to physical buttons

are enclosed in square brackets, for example, “press the [ENTER] button.” References to dis-

play page buttons are not emphasized, for example, “press the ENTER button.”

Display pages can be selected by using the [DISPLAY] buttons or the Left Tab Scroll, Right

Tab Scroll, and F1–4 buttons below the display. In order to simplify explanations, only the

[DISPLAY] button method is mentioned in the procedures. See “Selecting Display Pages”

on page 31 for details on all the ways in which pages can be selected.

Installing the 02R96

The 02R96 should be placed on a strong and stable surface, somewhere that complies with

the warnings and cautions listed in the previous sections.

v

02R96—Owner’s Manual

Contents

1 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 Control Surface & Rear Panel . . . . . . . . . . . . . . . . . 4

Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3 Operating Basics . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Turning On & Off the 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

About the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting Display Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Display Parameter Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Parameter Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Confirmation Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Title Edit Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selecting Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Selecting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Selecting Fader Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Selecting Encoder Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Assigning Parameters to the ENCODER MODE Assign Buttons . . . . . . . . . . . . . 37

4 Analog I/O & the AD Input Section . . . . . . . . . . . 39

AD Input Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Control Room Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Studio Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Omni Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

2TR Analog INs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5 Digital I/O & Cascading . . . . . . . . . . . . . . . . . . . . 41

Wordclocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

2TR Digital Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

2TR Digital Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

2TR In Sampling Rate Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Slot I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Dithering Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Monitoring Digital Input Channel Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Cascading Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6 Input & Output Patching . . . . . . . . . . . . . . . . . . . 52

Input Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Naming Input & Output Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Patch Select Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Patching with the Encoders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

vi

02R96—Owner’s Manual

7 Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Patching Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Metering Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Reversing the Signal Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Gating Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Attenuating Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

EQ’ing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Grouping Input Channel EQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Input Channel Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Compressing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Grouping Input Channel Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Delaying Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Muting Input Channels (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Grouping Input Channel Mutes (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Setting Input Channel Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Grouping Input Channel Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Routing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Panning Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Using Surround Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Sending Input Channels to Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Soloing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Direct Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Pairing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Using MS Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Viewing Input Channel Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Naming Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

8 Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Stereo Out Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Patching the Stereo Out to Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Routing Input Channels to the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Sending Bus Outs to the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Metering the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Monitoring the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Attenuating the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

EQ’ing the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Grouping Master EQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Stereo Out Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Compressing the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Grouping Master Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Muting the Stereo Out (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Grouping Master Mutes (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Setting the Stereo Out Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Grouping Master Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Balancing the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Delaying the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Viewing Stereo Out Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Naming the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

vii

02R96—Owner’s Manual

9 Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Patching Bus Outs to Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Routing Input Channels to Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Metering Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Monitoring Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Attenuating Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

EQ’ing Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Grouping Master EQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Bus Out Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Compressing Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Grouping Master Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Muting Bus Outs (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Grouping Master Mutes (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Setting Bus Out Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Grouping Master Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Delaying Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Soloing Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Pairing Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Sending Bus Outs to the Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Viewing Bus Out Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Naming Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

10 Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Patching Aux Send Masters to Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Setting the Aux Send Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Pre-Fader or Post-Fader Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Setting Aux Send Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Aux Send Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Viewing Aux Send Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Panning Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Metering Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Monitoring Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Attenuating Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

EQ’ing Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Grouping Master EQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Aux Send Master Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Compressing Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Grouping Master Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Muting Aux Send Masters (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Grouping Master Mutes (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Settings Aux Send Master Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Grouping Master Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Delaying Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Soloing Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Pairing Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Viewing Aux Send Master Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Naming Aux Send Masters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

viii

02R96—Owner’s Manual

11 Common Channel Functions . . . . . . . . . . . . . . . . . 87

Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Attenuating Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Using EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Grouping Output Channel EQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Using Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Compressing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Grouping Output Channel Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Delaying Channel Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Soloing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Pairing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Grouping Output Channel Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Grouping Output Channel Mutes (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Viewing Channel Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Viewing Channel Fader Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Naming Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

12 Monitoring & Talkback . . . . . . . . . . . . . . . . . . . . . 114

Control Room Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Studio Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Surround Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Using Talkback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

13 Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

About the Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

General Library Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Channel Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Input Patch Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Output Patch Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Effects Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Bus to Stereo Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Gate Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Comp Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

EQ Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Automix Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Surround Monitor Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

14 Internal Effects & Plug-Ins . . . . . . . . . . . . . . . . . . 131

About the Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Patching Effects Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Preset Effects & Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Editing Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

About Plug-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Configuring Plug-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Editing Plug-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

15 Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . 138

About Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Auto Scene Memory Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Storing & Recalling Scenes with the SCENE MEMORY Buttons . . . . . . . . . . . . . 140

Using the Scene Memory Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Fading Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Recalling Scenes Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Sorting Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

ix

02R96—Owner’s Manual

16 Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

About Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

What’s Recorded in an Automix? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Automix Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Channel Strip [AUTO] Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Automix Memory Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Fader Edit Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

Selecting the Timecode Source & Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

Creating a Time Signature Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Recording an Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Rerecording Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Parameter Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Punching In & Out Individual Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

Playing Back an Automix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Editing Events Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

17 MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

MIDI & the 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

MIDI I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

MIDI Port Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

MIDI Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

Assigning Scenes to Program Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Assigning Parameters to Control Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

Controlling Parameters by Using Parameter Changes . . . . . . . . . . . . . . . . . . . . . 167

Using Bulk Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

18 Pro Tools Remote Layer . . . . . . . . . . . . . . . . . . . . 169

Configuring Windows Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Configuring Macintosh Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Configuring the 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Configuring Pro Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

Control Surface Operation with the Pro Tools Remote Layer . . . . . . . . . . . . . . . 171

Selecting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Setting Channel Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Muting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Panning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Soloing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Viewing Send Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Configuring Sends as Pre or Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Setting Send Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Muting Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Panning Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Flip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

Assigning Inserts/Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

Editing Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

Bypassing Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Resetting Faders, Sends, & Panpots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Navigating the Edit Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Zooming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

Making Fine Adjustments to the Selected Region . . . . . . . . . . . . . . . . . . . . . . . . . 185

Scrub & Shuttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

x

02R96—Owner’s Manual

19 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 189

About the Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Assigning a Target to the Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Configuring the User Defined Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

Using the User Defined Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

About Machine Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

Configuring Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

Transport Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Using Shuttle & Scrub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Using the Locator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

Setting the Locate Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

GPI (General Purpose Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

20 Other Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 196

Using the User Defined Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

Setting Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

Using the Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

Checking the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

Initializing the 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

Appendix A: Parameter Lists . . . . . . . . . . . . . . . . . . . 202

USER DEFINED KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

USER DEFINED KEYS Initial Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

Input Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

Initial Input Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207

Output Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

Initial Output Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

Initial Input Channel Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

Initial Output Channel Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

Initial Input Port Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

Initial Output Port Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

GPI Trigger Source List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

User Defined Remote Layer Initial Bank Settings . . . . . . . . . . . . . . . . . . . . . . . . . 219

Effects Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223

Preset EQ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

Preset Gate Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255

Preset Compressor Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 255

Appendix B: Specifications . . . . . . . . . . . . . . . . . . . . . 260

General Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267

Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267

Analog Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

Analog Output Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

Digital Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

Digital Output Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

I/O Slot Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

Control I/O Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272

xi

02R96—Owner’s Manual

Appendix C: MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

Scene Memory to Program Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

Initial Parameter to Control Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275

Format Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275

Appendix D: Options . . . . . . . . . . . . . . . . . . . . . . . . . . 288

MB02R96 Peak Meter Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288

SP02R96 Wooden Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

Welcome

1

02R96—Owner’s Manual

1 Welcome

Thank you for choosing the Yamaha 02R96 Digital Mixing Console.

The 02R96 Digital Mixing Console offers 24-bit/96 kHz digital audio processing without

compromise, comprehensive surround mixing and monitoring, including bass manage-

ment, and hands-on control of popular DAW (Digital Audio Workstation) systems.

Sonic Spec

• Linear 24-bit, 128-times oversampling A/D converters

• Linear 24-bit, 128-times oversampling D/A converters

• 20 Hz–40 kHz (0.5, –1.5 dB) frequency response at 96 kHz sampling rate

• 105 dB typical dynamic range (AD Input to Stereo Out)

• 32-bit internal signal processing (58-bit accumulator)

Channel Architecture

• 56 Input Channels, with Direct Outs

• 8 Bus Outs, with to Stereo Out routing for subgrouping

• 8 Aux Sends

• Stereo Out

• Channels can be named for easy identiﬁcation

• Channel library with 127 user memories

I/O Architecture

• 16 analog mic inputs on balanced XLRs (plus 48 V phantom) 24 analog line inputs on bal-

anced phone jacks

• 16 analog inserts

• 32 inputs, 32 outputs via four mini-YGDAI slots and optional I/O cards, which

offer a vari-

ety of analog and digital I/O options, with support for all the popular digital audio

interconnect formats, including AES/EBU, ADAT, Tascam TDIF-1, and mLAN.

• 8 assignable Omni outputs

• 1 AES/EBU, 2 Coaxial 2-track digital input, with sampling rate converters for connecting

44.1/48 kHz legacy digital audio equipment

• 1 AES/EBU, 2 Coaxial 2-track digital output

• 2 analog 2-track inputs

• XLR and phono connector stereo outputs

• Control room monitor outputs

• Dedicated studio monitor outputs

• Double channel digital I/O for use with legacy 44.1/48 kHz multitrack recorders

• Cascade ports for cascading up to four 02R96s (i.e., 224 Input Channels)

2

Chapter 1—Welcome

02R96—Owner’s Manual

I/O Patching

• Any available input port can be patched to the Input Channels, Insert Ins, or Effects inputs

• Direct Outs, Insert Outs, Bus Outs, Aux Sends, and the Stereo Out can be patched to any

output port

• Input and output ports can be named for easy identiﬁcation

• Patches can be stored in the Input and Output Patch libraries

EQ

• 4-band parametric EQ on all Input and Output Channels

• EQ library with 40 presets, 160 user memories

Groups & Pairs

• Horizontal and vertical pairing of Input Channels

• Horizontal pairing of Bus Outs, Aux Sends, and Surround Pan

• 8 Input Channel, 4 Output Channel Fader groups

• 8 Input Channel, 4 Output Channel Mute groups

• 4 Input Channel, 4 Output Channel EQ groups

• 4 Input Channel, 4 Output Channel Compressor groups

Effects

• 4 internal effects processors

• Effects library with 52 presets, 76 user memories

• Multichannel effects for surround sound processing

• Joystick control of early reﬂections and reverb with the Reverb 5.1 effect

• Optional Waves 56K effects plug-in cards

• User deﬁned plug-ins for external effects control via MIDI, with Learn function

Dynamics

• Gates on all 56 Input Channels

• Gate library with 4 presets, 124 user memories

• Compressors on all Input Channels and Out Channels (74 in total)

• Compressor library with 36 presets, 92 user memories

Automation

• Dynamic automation of virtually all mix parameters, with 1/4-frame accuracy

• Automix library with 16 memories

• Snapshot style automation with 99 Scene memories, recallable via MIDI or Automix

• Individual fade time settings for all Input and Output faders

• Scene and library recalls

• Punch in/out entire channels with dedicated [AUTO] buttons, or individual parameters

• Editing fader moves with Fader Return, Fader Takeover, Absolute/Relative modes

• Ofﬂine event editing includes, erase, copy, move/merge, trim, duplicate, delete, and insert

Welcome

3

02R96—Owner’s Manual

Surround Sound

• 3-1 and 5.1 Surround modes

• Joystick control

• Bass management

• Monitor matrix

• Surround monitor speaker alignment functions

• Surround monitor library with 32 user memories

Remote Control

• Control and manage your 02R96 from your Mac or PC by using the bundled Studio Man-

ager software

• Remote Layers for external equipment control, including predeﬁned targets for controlling

DAW systems, and user deﬁned targets for controlling MIDI equipment, with Learn func-

tion

• Comprehensive machine control via MMC, including transport, track arming, jog/shuttle,

and built-in locator with eight Locate memories

• Assignable GPI (General Purpose Interface) port for external control and “Recording” light

MIDI

• Standard MIDI ports, USB TO HOST port, SERIAL TO HOST port, or mLAN MIDI I/O

• USB, SERIAL, and mLAN option offer multiport operation

• Scene recall, mix parameter control, Bulk Dump, MTC and MIDI Clock for Automix syn-

chronization, MMC for external machine control

Control Surface

• 25 touch-sensitive 100-mm motorized faders (touch sense used to select channels or punch

faders in/out during Automix recording)

• Use the faders to set channel levels or Aux Send levels

• Use the 24 Encoders to control Pan, Aux Send levels, or user assigned parameters

• Channels arranged into two Input Layers, Master Layer, and Remote Layer

• 320 x 240 dot LCD display with ﬂuorescent backlight

• Complete hands-on control of all channel functions via the SELECTED CHANNEL section

• 2-digit Scene memory display

• 4 EQ displays for frequency, gain, and Q

• 16 user-deﬁnable buttons make light work of repetitive tasks

4

Chapter 2—Control Surface & Rear Panel

02R96—Owner’s Manual

2 Control Surface & Rear Panel

Control Surface

25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56

AUX 1 AUX 2 AUX 3 AUX 4 AUX 5 AUX 6 AUX 7 AUX 8 BUS 1 BUS 2 BUS 3 BUS 4 BUS 5 BUS 6 BUS 7 BUS 8

PHONES

LEVEL

010

TALKBACK LEVEL

STUDIO

LEVEL

PHONES

23

24

21

22

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

GAIN

34

10

+

20

19

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

1 9 10 11 12 13 14 15 16

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

2

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

3

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

4

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

5

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

6

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

7

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

8

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

DISPLAY

STUDIO

AUX7 AUX8

SOLO

CONTROL

ROOM

STEREO

BUS

SLOT

CONTROL ROOM

2TR D1 2TR A1

2TR D2 2TR A2

2TR D3 STEREO

ASSIGN

1 ASSIGN2

SURROUND

CLEAR

DIMMER

CONTROL ROOM LEVEL

100

TALKBACK

SURROUND MONITOR LEVEL

EQUALIZER

EQ ON

LOW

Q

FREQUENCY

Q

FREQUENCY

Q

FREQUENCY

Q

FREQUENCY

DISPLAY

GAIN

LOW MID

GAIN

HIGH MID

GAIN

HIGH

GAIN

GATE ON COMP ON

GATE

COMP

RANGE

RATIO

ATT ACK

ATT ACKTHRESHOLD

THRESHOLD

DYNAMICS

DISPLAY

GATE / COMP

DECAY

RELEASE

HOLD

GAIN

SELECTED CHANNEL

LINK GRAB EFFECT

L

EVEN

R

LR

PAN / SURROUND

DISPLAY

ODD

DISPLAY ACCESS

PHASE /

INSERT

DELAY

12

3

4

56

78

STEREOFOLLOW PAN DIRECT

DISPLAY

ROUTING

SCENE MEMORY

DISPLAY

STORE RECALL

USER DEFINED KEYS

12345678

9 10111213141516

DISPLAY

REC

REW FF

STOP PLAY

SET

DISPLAY

MACHINE CONTROL

LOCATE MEMORY

1234

5678

INCDEC

ENTER

SHUTTLE

SCRUB

ON

SEL

AUTO

70

60

50

40

30

20

15

10

5

0

STEREO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 1 22 23 24

ON

SOLO

SEL

AUTO

AUTOMIX DIO SETUP UTILIT Y

MIDI REMOTE METER VIEW

PAIR GROUP INPUT

PATCH

OUTPUT

PATC H

DISPLAY ACCESS

AUX 2AUX 1 AUX 3 AUX 4

AUX 6AUX 5 AUX 7 AUX 8

AUX SELECT

DISPLAY

AUXPAN

ASSIGN 2ASSIGN 1

ENCODER MODE

DISPLAY

AUXFADER

FADER MODE

EFFECTS / PLUG INS

INTERNAL

EFFECTS

CHANNEL

INSERTS

PLUG INS

1234

DISPLAY

dB

Hz

kHz

dB

Hz

kHz

dB

Hz

kHz

dB

Hz

kHz

STEREO

12345678 9101112131415161718192021222324

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

50

40

30

20

15

10

5

0

5

17 18

18

17

19 20 21 22 23 24

MONITOR

DIGITAL MIXING CONSOLE

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

ON

SOLO

SEL

AUTO

PAD

125 1.00 4.00 10.0

MASTER25 48

REMOTE1 24

LAYER

00

AD Input Section (p. 5)

Channel strips (p. 5)

MACHINE CONTROL (p. 17)

AUX SELECT (p. 6)

FADER MODE (p. 7)

ENCODER MODE (p. 6)

DISPLAY ACCESS (p. 7)

EFFECTS/PLUG-INS (p. 9)

Display Section (p. 10)

SELECTED CHANNEL Section (p. 11)

LAYER (p. 15) STEREO (p. 15)

Data Entry & Transport

(p. 18)

Monitor, Phones & Talkback

Section (p. 19)

MONITOR Section (p. 20)

SCENE MEMORY (p. 16)

USER DEFINED KEYS (p. 16)

Control Surface

5

02R96—Owner’s Manual

AD Input Section

AD Input #1 is shown at the top; AD Inputs #17 and #18 below.

A

+48V ON/OFF switches (AD 1–16)

These switches turn on and off the +48 V phantom power feed to each INPUT A

(XLR-type connector). Phantom power is typically used to power condenser-type

microphones or direct boxes. See “Phantom Power (AD 1–16)” on page 39 for more

information.

B

PAD switches (AD 1–16)

These switches turn on and off the 26 dB pad (attenuator) for each AD Input. See “Pad

(AD 1–16)” on page 39 for more information.

C

GAIN controls

These controls adjust the gain of the AD Input Head Amps. They have an input sensi-

tivity of –16 dB to –60 dB or +10 dB to –34 dB when Pad is on. AD Inputs 17 to 24 have

an input sensitivity of +10 dB to –34 dB. See “Gain” on page 39 for more information.

D

PEAK indicators

These indicators light up when the input signal level is 3 dB below clipping. See “PEAK

& SIGNAL Indicators” on page 39 for more information.

E

SIGNAL indicators

These indicators light up when the input signal level is 20 dB below nominal. See

“PEAK & SIGNAL Indicators” on page 39 for more information.

F

INSERT ON/OFF switches (AD 1–16)

These switches are for turning on and off the AD Input inserts. See “AD Inserts (AD

1–16)” on page 40 for more information.

Channel strips

Channel strip #1 is shown here.

The function of each channel strip depends on the currently selected Layer. See

“Selecting Layers” on page 33 for more information.

A

Encoders

These controls are used to edit Input and Output Channel parameters. Their exact

operation depends on the currently selected Encoder mode and Layer. There are two

preset Encoder modes, Pan and Aux, and two assignable modes, with over 40 param-

eters to choose from. See “Selecting Encoder Modes” on page 36 for more informa-

tion.

The Encoders feature push switches that are used to punch the parameter currently

assigned to the Encoders in and out during Automix recording. See “Punching In &

Out Individual Parameters” on page 156 for more information.

B

AUTO buttons

These buttons are used to set Automix recording and playback for each channel.

Their exact operation depends on the currently selected Layer. Their indicators light

up orange in Record-Ready mode, red while recording, and green during playback.

See “Channel Strip [AUTO] Buttons” on page 149 for more information.

C SEL buttons

These buttons are used to select Input and Output Channels for editing with the

SELECTED CHANNEL section. Their exact operation depends on the currently

selected Layer. The [SEL] button indicator of the currently selected channel lights up.

See “Selecting Channels” on page 34 for more information. The [SEL] buttons can

also be used to pair channels, and to add and remove channels to and from the EQ,

Comp, Fader, and Mute groups.

1

2

3

4

5

6

1

ON

OFF

ON

26dB

-16

-60

GAIN

PEAK

SIGNAL

INSERT

+

48V

PAD

3

4

5

GAIN

34

10

+

GAIN

34

10

+

PEAK

SIGNAL

17 18

18

17

25

49

1

50

40

30

20

15

10

5

0

5

ON

SOLO

SEL

AUTO

1

2

3

4

5

6

6 Chapter 2—Control Surface & Rear Panel

02R96—Owner’s Manual

D SOLO buttons

These buttons are used to solo Channels. The [SOLO] button indicators of channels that

are soloed light up. See “Soloing Channels” on page 102 for more information.

E ON buttons

These buttons are used to mute Input and Output Channels. Their exact operation depends

on the currently selected Layer. The [ON] button indicators of channels that are on light up.

F Channel faders

These 100 mm touch-sensitive motorized faders are used to set the levels of Input Channels,

Bus Outs, and Aux Sends. Their exact operation depends on the currently selected Fader

mode and Layer. See “Selecting Fader Modes” on page 35 for more information. Faders can

be grouped for simultaneous operation. See “Grouping Input Channel Faders” on page 65

and “Grouping Output Channel Faders” on page 106 for more information.

Faders can also be used to select Input and Output Channels. See “Auto Channel Select &

Touch Sense Select” on page 34 for more information. They can also be used to punch chan-

nels in and out during Automix recording. See “Punching In & Out Individual Parameters”

on page 156 for more information.

AUX SELECT

A

AUX SELECT DISPLAY button

This button is used to select the following pages: Aux Send, Aux Send Pan, and Input Chan-

nel Aux View. See “Aux Sends” on page 79 for more information.

B AUX 1–8 buttons

These buttons are used to select Aux Sends when sending Input Channel signals to Aux

Sends. The button indicator of the currently selected Aux Send lights up. If the currently

selected Aux Send is paired, the indicator of its partner ﬂashes. See “Aux Sends” on page 79

for more information. These buttons can also be used to pair Aux Sends. See “Pairing Chan-

nels” on page 104 for more information.

ENCODER MODE

A

ENCODER MODE DISPLAY button

This button is used to select the Encoder Mode Assign page. See “Selecting Encoder Modes”

on page 36 for more information.

B PAN button

This button is used to select the Pan Encoder mode. Its indicator lights up when this mode

is selected. In this mode, the Encoders function as Pan controls while an Input Channel

Layer is selected. While the Master Layer is selected, Encoders 1–8 function as Input Chan-

nel 49–56 Pan controls, and Encoders 9–24 are inactive. See “Selecting Encoder Modes” on

page 36 for more information.

2

AUX 2AUX 1 AUX 3 AUX 4

AUX 6AUX 5 AUX 7 AUX 8

AUX SELECT

DISPLAY

1

4

AUXPAN

ASSIGN 2ASSIGN1

ENCODER MODE

DISPLAY

23

1

Control Surface 7

02R96—Owner’s Manual

C AUX button

This button is used to select the Aux Encoder mode. Its indicator lights up when this mode

is selected. In this mode, the Encoders function as Aux Send level controls when an Input

Channel Layer is selected. While the Master Layer is selected, Encoders 1–8 function as

Input Channel 49–56 Aux Send controls, and Encoders 9–24 are inactive. See “Selecting

Encoder Modes” on page 36.

D ASSIGN 1 & 2 buttons

These buttons are used to select the assignable Encoder modes. The button indicator for the

currently selected mode lights up. When an assignable mode is selected, the function of the

Encoders depends on the assigned parameter. Up to two parameters, from a list of over 40,

can be assigned to these two buttons. See “Assigning Parameters to the ENCODER MODE

Assign Buttons” on page 37 for more information.

FADER MODE

A FADER button

This button selects Fader mode, in which the faders control Input or Output Channel levels,

depending on the currently selected Layer. Its indicator lights up when this mode is selected.

See “Selecting Fader Modes” on page 35 for more information.

B AUX button

This button selects the Aux Fader mode, in which the faders control Aux Send levels. Its

indicator lights up when this mode is selected. See “Selecting Fader Modes” on page 35 for

more information.

DISPLAY ACCESS

A AUTOMIX button

This button is used to select the following Automix pages: Automix Main, Automix Mem-

ory, Fader Edit, Event Copy, and Event Edit. See “Automix” on page 145 for more informa-

tion.

B DIO button

This button is used to select the following pages: Word Clock Select, Dither, Cascade In,

Cascade Out, Sampling Rate Converter, and Higher Sample Rate Data Format. See “Digital

I/O & Cascading” on page 41 for more information.

C SETUP button

This button is used to select the following pages: Preferences 1, Preferences 2, Preferences 3,

MIDI/TO HOST Setup, GPI Setup, Input Port Name, Output Port Name, Time Reference,

and Time Signature.

1 2

AUXFADER

FADER MODE

AUTOMIX DIO SETUP UTILITY

MIDI REMOTE METER VIEW

PAIR GROUP INPUT

PATCH

OUTPUT

PATCH

DISPLAY ACCESS

9

6

5

8

7

1 2 3 4

J K L

La page charge ...

Yamaha 02R96 Le manuel du propriétaire

Ce manuel convient également à

Yamaha 02R96 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents