Southland SRTT196E Mode d'emploi

Marque: Southland

Modèle: SRTT196E

Catégorie: Mini motoculteurs

Taper: Mode d'emploi

Look inside for:

Page

Safety Definitions ................................1

Important Safety Information ......................2-4

Product Specifications ............................5

Parts & Features ................................5

Safety Decals ...................................6

Assembly .....................................7-8

Engine Preparation...............................9

Operation ....................................10-14

Maintenance..................................15-18

Technical Service .............................. 18

Troubleshooting ............................... 19

Warranty ...................................... 20

01/16/2018 Printed in China A203431

Operator’s Manual

REAR TINE

ROTARY TILLER

Record the following for future reference:

Mfg. Date Code: ____________________

Date of Purchase: ___________Attach a copy of your sales receipt.

Consumer Toll Free Number: 1-800-737-2112

Refer to the website for electronic manual and parts book.

www.southlandpowerequipment.com

IMPORTANT:

Thank you for purchasing this Southland® Tiller.

This manual provides complete instructions for safely operating and maintaining your tiller. Read and save these

instructions. Refer to this manual each time before using your tiller.

CALIFORNIA PROPOSITION 65 WARNING:

Engine exhaust, some of its constituents, and certain product components contain or emit chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm.

KEEP THIS MANUAL FOR FUTURE REFERENCE

If you need assistance or have any questions, CALL TOLL FREE: 1-800-737-2112

Model Nos. SRTT196E.1

SRTT196E.2

Look for this symbol to point out important safety precautions. It means: Attention! Become Alert!

Your Safety Is Involved.

Read operator’s manual before operating this machine. Failure to follow directions could result in

serious injury.

Thrown objects. Remove all rocks, stones, and foreign objects which could be thrown by machine.

Do not use if children or bystanders are present.

Rotating tines can cause serious injury. Keep hands, feet, and clothing away.

Wear eye protection complying with ANSI Z87.1 and hearing protection.

Disconnect spark plug wire when not in use or before servicing, cleaning, or performing maintenance on the unit.

Engine exhaust contains carbon monoxide, an odorless and deadly gas. NEVER run unit indoors or in a poorly

ventilated area.

Do NOT touch hot muffler or cylinder. These parts are extremely hot from operation and may remain hot for a short time

after operation.

To reduce risk of fire, clean spilled gas and oil and keep unit free from debris. Gasoline is extremely flammable. Allow

machine to cool before refueling.

Safety Definitions

• Save these instructions

Control and Operating Symbols

The following symbols are used on the product and in this manual to alert the operator of potential safety hazards. Read them

carefully, and understand their meaning.

Safety Alert Symbols

Safety Warning Symbols

The following symbols may be found on your tiller. Carefully read and understand their meaning.

Important Safety Information

DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor/moderate injury.

NOTICE

Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

Oil Fill Location: Do Not Overfill.

Clutch Lever: Depressing the upper lever engages the tines and drive wheels for the tilling operation.

Depressing the lower engages the tines and drive wheels for reversing the tiller.

Throttle Control: Move throttle lever to the left to increase engine speed. Move throttle lever to the right

to decrease engine speed.

Fuel ON/OFF Valve: Move fuel valve lever to the right to the ON position to operate the tiller.

Choke Lever: Move choke lever to the left for cold engine starting. Move choke lever to the right once engine is

started or for warm engine starting.

Responsibility of Operator

1. Carefully read and follow these safety instructions. Failure to do so can result in serious injury.

Know your product. Read and understand this manual before use. Compare the illustrations to unit. Learn location

and function of all controls. Thoroughly understanding the unit before use will result in the best performance and safety.

3. Follow all instructions when assembling the unit. If the unit was purchased in assembled condition, the operator must

check the unit carefully to make sure it was assembled according the instructions in the manual before use.

4. Regularly inspect the tiller. Make sure parts are not bent, damaged, or loose.

5. Use this equipment for its intended purpose only.

6. Operate the unit only with guards, shields, and other safety items in place and working correctly.

7. Service the unit only with authorized or approved replacement parts.

8. Complete all unit maintenance and adjustments according to the instructions in this manual.

WARNING

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm.

WARNING

To prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug

wire and put wire where it cannot contact the spark plug.

Preparation Safety

WARNING

• Read, understand, and follow all instructions on the machine and in this manual. Be thoroughly familiar with the

controls and the proper use of the tiller before starting. Know how to stop the engine quickly.

• Familiarize yourself with all the safety and operating decals on this equipment.

WARNING

• Thoroughly inspect the area where the tiller is to be used and remove all foreign objects. Your equipment can propel

small objects at high speed causing personal injury or property damage. Stay away from breakable objects, such as

house windows, auto glass, greenhouses, etc.

• Check that all nuts and bolts are tight and equipment is in good condition before each use.

Operation Safety

• Never allow children or young teenagers to operate the tiller.

WARNING

• Keep area of operation clear of all bystanders, particularly small children and pets.

• Only allow responsible individuals, who are familiar with the instructions, to operate the tiller.

WARNING

• Do not operate the tiller while under the influence of alcohol, drugs, or other medication which can cause drowsiness

or affect your ability to operate this machine safely.

• Do not use this machine if you are mentally or physically unable to operate the machine safely.

• Always wear ANSI compliant safety goggles or safety glasses with side shields when operating tiller to protect your

eyes from foreign objects, which can be thrown from the unit.

• Wear appropriate clothing such as a long sleeved shirt or jacket. Also wear long trousers or slacks. Do NOT wear

shorts. Do NOT wear loose clothing, which could get caught in this equipment.

• Always wear work gloves and sturdy footwear such as leather work shoes or short boots. These will protect ankles

and shins from small sticks, splinters, and other flying debris, and improve traction.

• It is advisable to wear protective headgear to protect against being struck by small flying particles, or being struck by

low hanging branches, twigs, or other objects, which may be unnoticed by the operator.

Important Safety Information

• Save all instructions

Important Safety Information

Important Safety Information (Continued)

• Save all instructions

Important Safety Information

Operation Safety (Continued)

WARNING

• Do not put hands or feet near or under rotating parts.

• Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

WARNING

• Exercise caution to avoid slipping or falling. Always be sure of your footing; keep a firm hold on the handle and walk;

never run. Never operate the tiller at high transport speeds on slippery surfaces.

• Never operate the tiller without good visibility or light.

DANGER

• Do not run the engine indoors or inside a closed area. The exhaust fumes are dangerous, containing CARBON

MONOXIDE, an ODORLESS AND DEADLY GAS.

• Never leave the tiller unattended when the engine is running. Stop the engine and make sure all moving parts have

stopped. Remove the wire from the spark plug.

• Watch for holes, ruts, bumps, or other rough ground. Tall grass can hide obstacles.

• Always look behind and down and use caution when using reverse or pulling the tiller towards you.

• Never attempt to start the tiller unless both wheels are in the locked position. This acts as a brake for the tiller.

Always start the tiller on the level surface.

WARNING

• Disengage clutch lever and stop engine before leaving the tiller in operating position. Wait until the tines come to a

complete stop before removing debris or making any adjustments to the tiller.

CAUTION

• Do not attempt to till hard soil, till too deep or till at too fast a rate that can overload the tiller.

• If the tiller should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and prevent it from

touching the spark plug. Check immediately for the cause. Vibration is generally a warning of trouble.

Fuel Safety

WARNING

• Gasoline is extremely flammable, and gasoline vapors can explode if ignited. Handle with care.

• Use an approved container.

• Check fuel supply before each use, allowing space for expansion as the heat of the engine and/or sun can cause fuel

to expand.

• Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

WARNING

• Do not smoke while refueling.

• After refueling, replace fuel tank cap securely and wipe up spilled fuel.

• Never store fuel or tiller with fuel in the tank inside a building where fumes may reach an open flame.

• Never fill gasoline containers or the tiller fuel tank inside of a vehicle or in a truck bed. Accidental electrical static

discharge can ignite fuel vapors which could result in serious injury or death.

Storage Safety

•

Always refer to the operator’s manual instructions for important details if the tiller is to be stored for an extended period.

• Never store the tiller with fuel in the fuel tank inside a building where ignition sources are present such as water

heaters, space heaters, clothes dryers, etc.

Important Safety Information (Continued)

• Save all instructions

Important Safety Information

Storage Safety (Continued)

• To reduce fire hazard, keep tiller free of grass, leaves, or other debris build-up.

• Allow the engine to cool before storing in any enclosure.

Repair, Maintenance, and Adjustment Safety

• After striking a foreign object, stop the engine. Remove the wire from the spark plug and keep the wire away from the

plug to prevent accidental starting. Thoroughly inspect the tiller for any damage. If damaged, have the equipment

repaired by a trained technician before restarting and operating.

WARNING

• Stop the engine before cleaning, repairing, or inspecting the unit. Make sure all moving parts have stopped. Let the

engine cool, disconnect the spark plug wire and move it away from the spark plug.

• Never attempt to make any adjustments while the engine is running except when specifically recommended by the

manufacturer.

• Keep the tiller in safe working condition. Check all fasteners at frequent intervals for proper tightness.

• When servicing or repairing the tiller, do not tip the machine over or up unless specifically instructed to do so in this

manual. Service and repair procedures can be done with the tiller in an upright position. Some procedures will be

easier if the machine is lifted on a raised platform or working surface.

• Use only original equipment or authorized replacement parts.

WARNING

• Never tamper with safety devices. Check their proper operation regularly.

• Do not change the engine governor setting or over-speed engine.

• Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine debris filter mounted and clean.

Children Safety

WARNING

• Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the

tiller and the tilling activity.

• Keep children out of the tilling area and under the watchful care of a responsible adult.

• Never assume that children will remain where you last saw them.

• Be alert and turn tiller off if children enter the area.

• Before and while moving backwards, look behind and down for small children.

• Never allow children to operate the tiller.

• Use extra care when operating near blind corners, shrubs, trees, or other objects that may obstruct vision.

Parts & Features

1. Tines

2. Tine Shield

3. Wheels

4. Wheel Lock Pins

5. Muffler

6. Air Filter

7. Recoil Starter Handle

8. Spark Plug / Spark Plug Wire

9. Depth Regulator Bar

10. Throttle Control

11. Fuel ON/OFF Valve

12. Choke Control

13. On/Off Switch

14. Fuel Tank Cap

15. Oil Dipstick

16. Forward Lever

17. Reverse Lever

18. Front Guard

Figure 1

Product Specifications

• Save all instructions

Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 lb (70 kg)

Tilling Width . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 in (45.7 cm)

Tilling Depths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .up to 8”

Tine Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . .11 in (27.9 cm)

Gasoline Type .........Regular Unleaded/87 Octane (min.)

Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . 3.5 US qt. (3.3 L)

Engine Oil Type (API SG-SL) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10W-30 is recommended for all service temperatures.

See page (10) for additional information.

Engine Oil Capacity . . . . . . . . . . . . . . . . . . . 20 US oz (600 ml)

Transmission Oil Type . . . . . . . . . . . SAE 85W-140 / 90W-140

Transmission Oil Capacity . . . . . . . . . . . . . . 30 US oz (900 ml)

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Torch F7RTC

Spark Plug Gap . . . . . . . . . . . . . . 0.028-0.031 in (0.7-0.8 mm)

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OHV 4-stroke

Engine Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 196cc

Engine Speed (Full Throttle) . . . . . . . . . . . . . . . . . . . 3600 rpm

Engine Speed (Idle) . . . . . . . . . . . . . . . . . . . . . . . . . . 2100 rpm

Torque Rating........ 9.6 ft-lbs gross torque per SAE J1940

Bore Diam. x Stroke. . . . . . . . . . . . 2.7 x 2.13 in (68 x 54 mm)

Intake Valve Clearance . . . . 0.004 - 0.006 in (0.10 - 0.15 mm)

Exhaust Valve Clearance . . . 0.006 - 0.008 in (0.15 - 0.20 mm)

Angle of Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 degrees

Tire Size .............. 13x5.00-6 Directional Tractor Tread

Tire Pressure . . . . . . . . . . . . . . . . . . . . . 25 psi min/30 psi max

Safety Decals

• Save all instructions

This tiller has been designed and manufactured to provide you with the safety and reliability you would expect from an

industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to

operated this equipment safely and effectively, we have placed several safety labels on the tiller to remind you of this impor-

tant information while you are operating the unit.

These important safety labels are illustrated below, and are shown here to help familiarize you with the location and con-

tent to the safety messages you will see as you perform normal tilling operations. Please review these labels now.

If you have any questions regarding their meaning or how to comply with these instructions, reread the complete safety

instruction text on the preceding pages, or contact your local dealer.

Should any of the safety labels become unreadable because of being worn, faded, or otherwise damaged during the use of

your tiller, please contact your local authorized dealer to order replacement labels.

The safety labels are easily applied, and will act as a constant visual reminder to you and others who may use the equipment.

Following the safety instructions is necessary for safe, effective operation of your tiller.

• Keep away from

rotating tines.

• Contact will result

in injury.

• Gasoline is flammable. Allow engine to cool at least 2 minutes

before refueling.

• Operation of this equipment may create sparks that can start

fires around dry vegetation. A spark arrestor may be required.

The operator should contact local fire agencies for laws or

regulations relating to fire prevention requirements.

1. Insert the locking pin to secure the

wheels in locked position.

2. Turn the Engine Switch to the "ON" position.

3. Move the Fuel Valve lever to the "ON" position.

4. Move the Choke lever to the "START" position.

5. Adjust the Throttle Control to the high speed.

6. Pull the Starter Handle until engine starts

7. After starting the engine, move the Choke lever

to the "RUN" position.

Depth Regulator

Bracket

Depth Regulator

Lever

Figure 3

Wheel lock pin in tiller operating position

(wheel hub and axle holes)

FRONT

Figure 2

Assembly

• Save all instructions

If you need assistance or find any parts missing,

CALL TOLL FREE: 1-800-737-2112.

Read and follow the assembly instructions. Do not discard

any parts or materials until the unit is assembled.

References to the right or left side of the tiller are from the

viewpoint of the operator’s position behind the tiller.

WARNING

Do not operate tiller if it is damaged or not completely and

correctly assembled.

WARNING

Before doing any assembly or maintenance to the unit,

remove the wire from the spark plug.

WARNING

Always wear ANSI compliant safety glasses with side

shields while assembling the tiller.

The following components will be found in the carton.

Quantities shown in ( ).

1. (1) Tiller

2. (1) Handle Assembly

3. (1) Depth Regulator Bar

4. (1) Tiller Operator’s Manual

5. (1) Engine Manual

6. (1) Bottle of Engine Oil

7. (1) Parts bag containing the following:

a. (2) M10x25 mm ange head bolts, lock washers and

nuts for assembling lower handle

b. (4) M8x50 mm saddle bolts and washers for

assembling upper handle

c. (4) Handle knobs for assembling upper handle

d. (2) Wheel locking pins

e. (1) Pin

8. (2) Wheel and tire assemblies

9. (1) Front Guard

1. Remove all parts and packaging components.

2. Use a utility knife to cut all four vertical edges and lay

the side panels flat around the tiller.

3. Remove any remaining packaging.

How to Remove Tiller from Carton

Assembly Instructions

The tiller comes fully assembled except for a few parts.

The following instructions will help you complete the

tiller assembly.

Install the Wheels (See Figure 2)

1. Assure cupped washer is installed onto wheel axle.

2. The tiller wheels are directional. For best performance

install the wheels with the tire thread facing the direction

as shown.

3. Slide the wheel hub onto the wheel axle.

4. Align the wheel hub hole with the hole in the axle and

insert the locking pin.

5. Rotate the locking pin ring to lock the pin in position.

Install the Depth Regulator (See Figure 3)

1. Insert the depth regulator into the bottom of the depth

regulator bracket.

2. Insert the pin through the bracket and lever.

Assembly (Continued)

• Save all instructions

If you need assistance or find any parts missing, CALL

TOLL FREE: 1-800-737-2112.

Attach Lower Handle (See Figure 4)

1. Loosen the lower handle bolts, if required.

2. Align the lower handle holes to the middle height

adjustment holes in the transmission cover and install

the M10 x 25 mm bolts, flat washers, lock washers and

nuts. Tighten all four bolts at this time.

Attach Upper Handle (See Figure 5)

1. Slide the upper handle down over the lower handle and

align the holes.

2. Insert the saddle bolts into the holes as shown and secure

with the handle knobs.

3. Tighten the handle knobs securely.

4. Secure control cables to handle using cable ties.

Install Front Guard (See Figure 6)

1. Install guard using four M8 x 20 mm hex head bolts,

split lock washers, at washers and nuts.

Saddle Bolts

Saddle Bolts Handle Knobs

Handle Knobs

Figure 5

Transmission Cover

Height

Adjustment

Holes

Lower Holes

Figure 4

Figure 6

Saddle Bolts

Saddle Bolts Handle Knobs

Handle Knobs

Figure 5

Oil Fill Cap/

Dipstick

Upper Limit

Lower Limit

Figure 7

Figure 8

Fuel Tank Cap

Depth Regulator

Lever

Oil Fill Cap/Dipstick

Engine Preparation (Continued)

• Save all instructions

Engine Oil

NOTICE

Engine shipped without oil. Failure to add oil will result in

serious engine damage.

A bottle of engine oil is included with your tiller. Refer to the

chart on the right for alternative oil types to use at different

temperatures. Always use a high quality detergent oil

classified “For Service, SG, SH, SJ” or higher. Do NOT use

special additives.

NOTICE

Always use recommended oil type. Using dirty oil or

incorrect oil type such as 2-stroke engine oil will shorten

engine life.

NOTE: Engine Oil Capacity is 20 oz. (0.6 L).

How to Check Oil Level and Fill to Proper Level

WARNING

Before checking oil, make sure engine is off, and spark

plug wire has been disconnected from spark plug.

1. Place the tiller on a level surface and make sure the

depth regulator lever is set so the main frame of the tiller

is level. (See Figure 6)

2. Remove the oil ll cap/dipstick and wipe clean with

cloth. (See Figure 6)

3. Insert dipstick into ll spout but do NOT screw in.

Remove dipstick and check oil level.

4. When oil level is full, the oil will be at upper limit on dip

stick. If oil level is near or below the lower limit, oil must

be added. (See Figure 7)

5. Add oil slowly until the oil level reaches the upper limit

of the dipstick. Use a funnel or nozzle to reduce spillage.

NOTICE

Frequently check oil level while filling. DO NOT OVERFILL.

DO NOT UNDER FILL. Running engine at improper oil

level will seriously damage engine.

6. Replace and tighten dipstick.

7. Clean up any spilled oil.

NOTE: The transmission comes from the factory with the

proper amount and type of gear oil.

SAE

TEMP 100° F

40° C

-20

-20-30 -10

2010

40 60 80

Ambient Service Temperature

SAE 10W-30

SAE 30

Operation

• Save all instructions

Pre-Start Inspection

1. Make sure all safety guards are in place and all nuts and bolts are secure.

A. Verify the air pressure in both tires is 25 - 30 psi before each use.

2. Check oil level in engine crankcase. See your engine manual for procedure and specications.

3. Inspect air cleaner for cleanliness. See your engine manual for procedure.

4. Check the fuel supply. Use fresh unleaded gasoline with an octane rating of 87 or higher. Do not use gasoline

containing more than 10% ethanol. Use of non-ethanol fuel is best. We recommend the continuous use of a fuel

additive /stabilizer to counteract the effects of ethanol. These additives also prolong the shelf life of gasoline. Fill the

fuel tank no closer than 1 inch from top of tank to provide space for expansion. See your engine manual for

fuel recommendations.

5. Be sure spark plug wire is attached and spark plug is tightened securely.

6. Check position of wheels and wheel lockouts.

7. Check depth regulator lever position.

8. Examine underneath and around engine for signs of oil or fuel leaks.

9. Inspect fuel hoses for tightness and fuel seepage.

10. Look for signs of engine damage.

11. Remove excessive debris from mufer area and recoil starter.

IMPORTANT: Engine is shipped from factory without oil. You must add engine oil before starting engine.

CAUTION

Please do not start your tiller until you have read the manual that came with your tiller, and the sections in this manual

tiller controls, adjustments and safety. If you have read these, follow the steps below to start your tiller. Always perform

this pre-start checklist before starting the engine.

WARNING

Gasoline is highly ammable and must be handled with care. Never ll the tank when the engine is hot or running. Always

move outdoors to ll tank.

Wheels must always be locked in the tilling position when engine is running. Do not operate the tiller with the wheel

lockouts unlocked. Always set the wheels in tilling position before starting engine.

Always put depth regulator lever in the transport position before starting engine. Tines should clear ground.

DANGER

Always keep hands and feet clear of rotating machine parts.

Start-Up

The controls required to start and run the tiller are located on the engine and are marked with the icon for choke, slow and

fast for the throttle, and on/off fuel valve. A more detailed description of engine operation and all related precautions and

procedures can be found in the engine manufacturer’s manual that accompanies each tiller.

Cold Starts

1. Turn the Engine Switch to the “on” position.

2. Move the Fuel Valve lever to the right for “on” position.

3. Move choke lever to the left for full choke “start” position.

4. Move throttle lever to “start” or “fast” position.

5. Pull starting rope out slowly one time and allow to return normally.

6. Pull starting rope out rapidly, and allow rope to return normally.

7. When engine starts, gradually move choke lever to “run” position and increase throttle speed.

Restarting a Warm Engine

NOTE: Restarting an engine that is already warm from previous running does not normally require use of the choke.

1. Move throttle lever to “start” position or “fast” position.

2. Pull starting rope out rapidly until engine starts. Allow rope to return normally. Repeat until engine starts.

3. Adjust throttle speed to “fast” for best tiller performance.

Operation (Continued)

• Save all instructions

Idle Speed

Use the “slow” position on the throttle lever to reduce stress on the engine when tilling is not being performed. Lowering

the engine speed to “idle” will help extend the life of the engine, as well as conserve fuel and reduce the noise level of

the equipment.

Operating Speed

For normal tilling, set the throttle lever to ˝fast˝.

Shutting Down

To stop the engine at any time, turn engine on/off switch to the off position. To stop wheels and tines at any time, release

drive safety control levers to neutral position.

Tilling

1. Adjust the depth regulator lever to desired tilling depth.

WARNING

Raise depth regulator up one hole at a time, testing tiller operation after each raise. Raising depth regulator too high can

result in loss of control of tiller!

2. Move the throttle control to fast.

3. Place the tiller in forward by pushing down on the drive safety control lever (FORWARD)--this will engage the

wheels and tines.

NOTE: You can slow the tiller’s forward advance at any time by putting slight downward pressure on the handlebars. You

can stop the tiller by releasing the drive safety control levers to the neutral position.

NOTICE

Always press the forward or reverse drive levers down completely onto the handle bar. Failure to do so may result in

excessive drive belt wear and premature drive

belt failure.

WARNING

Temperature of mufer and nearby areas may exceed 150˚F. Avoid these areas. Do not move choke control to stop

engine, backre or engine damage may occur. To stop wheels and tines at any time, release drive safety control levers to

neutral position. Always release drive safety control levers to neutral position AND STOP THE ENGINE before adjusting

the depth of the regulator lever.

DANGER

Engine and surrounding parts become extremely hot during

normal use and will cause serious burn injuries if touched before the engine has cooled. Allow engine to cool completely

before touching these hot surfaces.

IMPORTANT: practice operating the controls and tiller with tines out of ground before beginning to till. It is important that you

know how to use the tiller properly, keep control at all times, stop the tines and wheels from turning, and stop the engine if nec-

essary. If you do not know how to do these things, read the controls, adjustments and safety sections before proceeding.

Drive Safety Control Levers

Operation (Continued)

• Save all instructions

CAUTION

Do not operate both “FORWARD” and “REVERSE” drive

safety control levers at the same time.

This information is provided here only to introduce the

controls. Do not start the engine at this time. Starting and

operating instructions are given on page 11. Please read

this section and all operating and safety instructions before

starting your tiller.

As a safety precaution, the drive safety control levers will

not lock in the forward or reverse position.

WARNING

Do not x the forward or reverse drive levers in the drive

position by any other means than manually using your right

hand. Do not tie or otherwise secure the levers in the drive

position.

To stop the wheels and tines at any time release the drive

safety control levers.

Forward Lever (See Figure 9)

Engages wheels and tines into forward. Pushing down

the drive safety control lever (FORWARD) toward the

handlebar engages the wheels and tines. Releasing the

lever stops the wheels and tines and brings the tiller to a

complete stop.

Reverse Lever (See Figure 10)

Engages wheels and tines into reverse.

Pulling the drive safety control lever (REVERSE) toward

the handlebar reverses the tiller. Releasing the lever stops

the wheels and tines.

Forward Lever

Engaged

Figure 9

Reverse Lever

Engaged

Reverse Lever

Figure 10

Adjustments

Operation (Continued)

• Save all instructions

WARNING

Engine should be off before adjusting any controls.

Extreme caution should be used when operating tiller in the

reverse direction.

Wheel Lock Pins (See Figures 2 on pg. 8 and 11)

Place wheels in tilling position.

1. Remove lock pin. Align hole in axle with hole in wheel hub.

2. Insert lock pin through holes, fold lock pin ring to secure

pin to axle.

3. Firmly lock wheel and axle together before tilling.

4. Repeat for other wheel.

WARNING

Always have both wheel lock pins in or out. Do not operate

tiller with only one wheel locked.

To place wheels in free-wheel position.

1. Remove lock pin. Slide wheel inward toward machine.

2. Insert pin in axle only, fold lock pin ring to secure pin to axle.

3. Wheel should turn freely on axle.

Handlebar Height Adjustment (See Figure 4 on pg. 9)

Adjust handlebar height.

The ideal height of the handlebar varies with operator

height and the depth of tilling. To adjust handlebar

height:

1. Unscrew nuts and remove top bolts on each side.

2. Loosen the lower bolts. Do not remove.

3. Align handlebar to desired holes on the lower

handlebar mount.

4. Install bolts and nuts. Retighten all four bolts securely.

Depth Regulator (See Figure 3 on pg. 8)

Tilling depth is controlled by the height of the

depth regulator. To adjust tilling depth:

1. Remove pin.

2. Raise the depth regulator to position tines at chosen

tilling depth.

3. Align hole in depth regulator with hole in depth regulator

bracket and replace pin.

Depth Regulator Down = Shallower tilling.

Place the pin in the top hole of the depth regulator for

shallowest tilling.

Depth Regulator Up = Deeper tilling.

Place the pin in the bottom hole of the depth regulator for

deepest tilling.

Wheel lock pin in free-wheel position

(axle holes only)

FRONT

Figure 11

WARNING

Do not adjust tilling depth unless drive safety control levers are

released to neutral position.

Always set the depth regulator in the transport position

before starting engine, that is, place the detent pin in the

highest hole of the depth regulator.

Operation (Continued)

• Save all instructions

Tilling Tips

The key to successful tilling is to begin with a shallow cut on the first pass, and then work an inch or two deeper on each

successive pass.

• Tilling depth will vary with ground conditions.

• When beginning to till in unbroken ground or in extremely hard soil, set the pin in the highest hole of the depth

regulator (follow instructions under Tilling section). This will allow for shallow tilling. With the depth regulator in this

position, make several light passes over the area to be tilled. Reset for deeper depths with successive passes.

• If tiller jumps or skids uncontrollably, lower the depth regulator by placing the pin in a higher hole. This will allow for

shallower tilling. Hold firmly to the handlebars to control sudden lurches.

• If weeds, tall grasses, vines, or other materials clog or jam the tines, reverse the tiller to unwind vegetation.

WARNING

Immediately release the drive control levers if the tines jam or you strike a foreign object. With drive control levers in

neutral position, stop the engine. Disengage the spark plug wire. When tines have stopped, remove foreign objects and

check for damage.

WARNING

Extreme caution must be taken in selecting tilling depth. If you attempt to till too deeply for soil conditions (with the depth

regulator lever in too high a position) loss of control could result. If removing material from the tines by hand, stop engine

and remove spark plug wire rst.

Cultivating Tips

If you plan to use your tiller for cultivating:

• Plant rows on 20” - 22” centers for ease of turning.

• Set the depth regulator lever with the detent pin in one of the higher holes. This will allow for shallow cultivation

necessary to turn over weeds, and break up and aerate the soil.

Maintenance

• Save all instructions

Maintenance Schedule

WARNING

Before performing any maintenance, turn engine off and remove the wire from the spark plug to prevent accidental starting

and serious injury.

IMPORTANT: The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the tiller as instructed in this manual, and only use genuine replacement

parts. The following table lists required periodic maintenance.

CAUTION Important notes about maintenance schedule:

1. Re-check tightness of all fasteners after first 2 hours of initial use

2. Change engine oil after first 5-8 hours of initial use

3. Change oil every 25 hours if operating under heavy load or in high temperatures

4. Clean air filter every 10 hours if operating under dusty conditions.

WARNING

Use only GENUINE replacement parts. Other parts may damage the unit or result in injury.

PERIODIC MAINTENANCE SCHEDULE TABLE

Service Records-

Fill in dates as you complete regular

service

Before

Each Use

After

Every

10 Hours

of Use

After

Every

25 Hours

of Use

After Every

50 Hours of

Use

After

Every

100 Hour

of Use

Before

Each

Season

Before

Storage

See

Note

Below

Check air pressure in tires. √

Check Engine Oil Level,

Fill to Proper Level √ √

Clean Debris From Unit √ √ √

Lubricate All Pivot Points √ √ √

Check Fasteners for Tightness √ √

Check Drive Belts

Replace if Necessary √ √

Check Tines for Wear or Damage

Replace if Necessary √ √

Check Fuel Line

Replace if Necessary √ √

Lubricate Wheel Axles √ √ √

Check Spark Plug

Replace if Necessary √ √

Change Engine Oil √ √ √

2,3

Clean Air Filter

Replace if Necessary √ √

Replace Spark Plug √

Clean Combustion Deposits from

Cylinder, Piston, and Valves √

Check Transmission Oil √ √

Maintenance (Continued)

• Save all instructions

Servicing the Tiller

The following information will help you make the necessary

checks and perform the procedures required to follow the

normal care recommendations made for your tiller unit. If

you prefer, your local authorized dealer can make these

checks and perform the required procedures for you.

WARNING

To prevent accidental starting:

Engine must be turned off and cool. The spark plug wire

must be removed and secured from spark plug before

checking and adjusting engine or equipment.

Change Forward/Reverse Belts

(See Figure 12 and 13)

1. Turn off engine. Engine must cool completely

before proceeding.

2. Remove spark plug wire and secure away from spark plug.

3. Reduce the belt tension by loosening the forward and

reverse cable lower jam nut.

4. Remove the upper and lower belt guards.

5. To remove the reverse drive belt:

a. Remove the reverse belt idler.

b. Slide the belt free of the reverse belt guides and

engine pulley.

c. Pull belt down and away from the transmission pulley.

6. To remove the forward drive belt:

a. Remove the two forward belt guide studs and

forward belt idler assembly.

b. Slide the belt free of the engine pulley.

c. Pull the belt down and away from the transmission

pulley.

7. To install the forward drive belt:

a. Insert the belt from underneath the unit and up

around the rearward portion on the engine pulley.

b. Place the lower loop of the belt around the rearward

portion of the transmission pulley.

c. Replace the two forward belt guide studs and

forward belt idler assembly.

8. To install the reverse drive belt;

a. Insert the belt from underneath the unit and up

around the reverse belt idler.

b. Place the lower loop of the belt around the forward

portion of the transmission pulley.

c. Replace the reverse belt idler into the reverse belt

idler bracket. The belt should not go around the

engine pulley. Be sure the belt is inside of the

reverse belt guide studs.

9. Tighten the forward and reverse lower jam nut.

10. Check the belt tension. The belts should be loose with

the drive levers disengaged.

ENGINE PULLEY

Forward Belt

Reverse Belt

TRANSMISSION

PULLEY

Reverse Belt Idler

Forward Belt Idler

Figure 13

11. Replace the upper and lower belt guards.

12. Re-attach the spark plug wire to the spark plug.

13. Follow Operating Instructions – start the engine and

operate the forward drive lever to check for proper

cable adjustment and belt tension.

14. Start the engine and operate the reverse drive lever to

check for proper cable adjustment and belt tension.

WARNING

The tines or wheels should not rotate with the engine

running, the depth regulator set at transport height

(lowest height) and the drive lever not engaged.

Figure 12

wire

tab

Maintenance (Continued)

• Save all instructions

Engine Maintenance

Refer to the engine manual included in your parts packet

for information on engine maintenance. Your engine

manual provides detailed information and a maintenance

schedule for performing the following tasks:

1. Check oil level before each use or after every 8 hours

of operation.

2. Change oil after first 5-8 hours of operation. Change oil

while engine is warm. Refill with new oil of

recommended grade.

3. Check spark plug yearly or every 100 hours of operation.

4. Service air cleaner.

5. Keep engine and parts clean.

6. Check engine and equipment often for loose nuts and

bolts, keep these items tightened.

Check or Fill Engine Crankcase

IMPORTANT: Engine is shipped from factory without oil. You

must add engine oil before starting engine.

1. Add oil according to engine manual. Do not overll.

Use a clean, high quality detergent oil. Do not mix oil

with gasoline. Oil level must be full. Check the oil level

by removing oil fill plug.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

Check Tiller Transmission Oil

IMPORTANT: Tiller transmission is shipped from factory with

the proper amount of oil. When replacing oil, the tiller

transmission holds 27-30 ounces. Do not overfill.

Check the oil level annually. To check the oil level:

1. Move tiller to level ground.

2. Remove oil level dipstick located between the

handlebar mounts on the engine mount. If the oil

level is near or below the lower limit, fill the oil to

recommended level with SAE 85W-140 / 90W-140.

3. Replace oil level dipstick in the filler hole.

4. Note that the drive wheel transmission and rear tine

transmission are one common reservoir. When you add

to the front transmission, you must wait a short period

of time for the oil to flow rearward and equalize in

both front and rear. The dipstick will read correctly on

level ground for both gear units.

Check Tire Pressure

Recommended tire pressure is 25-30 PSI. If tires do not

have equal pressure, tiller will pull to one side. Low tire

pressure may result in damage to tire tube.

Lubrication

Proper lubrication of moving mechanical parts is critical for

proper care and maintenance. Oil the moving parts shown

at 10 hour intervals using a 30 weight oil.

Clean Tine Axle Shaft

1. Turn off engine. Engine must be cool.

2. Remove spark plug wire and secure from spark plug.

3. Tip the tiller forward. Block the tiller in position so that it

rests on the engine mount and the tines are exposed.

4. Remove all vegetation, string, wire, and other material

that may have accumulated on the axle between the

inside set of tines and the seal cover on the

transmission housing.

5. Tip the tiller back to a level position.

6. Replace spark plug wire.

Gear Case Dipstick

Transmission

Cover Plate

Figure 14

How to Prepare for Storage

WARNING

Never store the tiller indoors with fuel in the fuel tank. Never store in an enclosed, poorly ventilated area where fumes

could reach an open ame, a spark or a pilot light as on a furnace, water heater or clothes dryer. Allow engine to cool

before storing unit.

WARNING

Do not remove gasoline while inside a building, near a re, or while you smoke. Gasoline fumes can cause an explosion

or a re.

NOTE: A yearly checkup or tune-up at an authorized service center will make sure that the tiller will provide maximum

performance for the next season.

When the tiller is put in storage for thirty days or more, the following steps should be followed to make sure the tiller is in good

condition the next season. To prevent fuel gum deposits and corrosion in the unit’s carburetor and fuel system, it is highly

recommended to use a fuel additive/stabilizer formulated for ethanol fuels. Follow the stabilizer manufacturer’s instructions. Run

the engine for at least 5 minutes after adding stabilizer.

1. Let the engine run until it is out of gasoline. Remove the carburetor screw from bowl and drain fuel. Tilt unit slightly to

remove all fuel. Replace screw.

2. Change the oil by following instructions under “How to Change the Oil.”

3. Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil-start handle so

that the oil will protect the cylinder. Install a new spark plug in the cylinder. Pull starter handle slowly a few times to

distribute oil. Pull recoil slowly until resistance is felt. This will close the cylinder valves.

WARNING

Do not attach spark plug wire to spark plug when storing unit.

4. Clean tiller. Remove all dirt, leaves, debris, grease, etc. from the tiller - including cylinder cooling fans, recoil starter

cover holes, under fuel tank, and under mufer.

5. Check the tiller for worn or damaged parts. Have damaged parts replaced if necessary.

6. Tighten any loose hardware.

7. Apply lubrication as directed in Maintenance section.

8. Put the unit in a building that has good ventilation.

9. Cover the tiller with a breathing material.

Maintenance (Continued)

• Save all instructions

You may have further questions about assembling, operating, or maintaining this TILLER. If so, you can contact our

Technical Service Department at 1-800-737-2112 (English only).

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

6700 Wildlife Way

Long Grove, IL 60047

Technical Service

When contacting the Technical Service Department, have ready:

• Your Name

• Your Address

• Your Phone Number

• Model Number of Product

• Date of Purchase (include copy of receipt for written requests)

• Date Code on Product

If you need assistance or have any questions,

CALL TOLL FREE: 1-800-737-2112.

PROBLEM POSSIBLE CAUSE(S) SOLUTION(S)

Engine difficult to start 1. Out of fuel

2. Engine Switch Off

3. Engine is not primed

4. Spark plug wire disconnected

5. Fouled spark plug

6. Dirty Carburetor

7. Clogged air filter

8. Contaminated Fuel

1. Add fresh fuel

2. Turn engine switch on

3. Move choke lever to ON position.

4. Attach spark plug wire to spark plug

5. Remove spark plug. Inspect.

Replace if necessary

6. Take unit to an authorized service center for

Carburetor cleaning

7. Remove and clean air filter

8. Drain fuel tank. Clean fuel tank. Fill with

fresh fuel

Engine Problems

Engine smokes excessively

Engine runs very “rough”

Engine runs erratically

Engine cannot maintain full speed

1. No Engine Oil

2. Engine oil not at proper level

3. Fouled spark plug

4. Clogged air filter

5. Contaminated Fuel

6. Carburetor out of adjustment

1. Add engine oil

2. Check engine oil. Add or drain engine

oil if necessary

3. Remove spark plug. Inspect.

Replace if necessary

4. Remove and clean air filter

5. Drain fuel tank. Clean fuel tank. Fill with

fresh fuel

6. Take unit to an authorized service center for

carburetor adjustment

Excessive vibration / noise 1. Loose parts

2. Engine problems (above)

3. Abnormal noise or squeal coming from

belt drive

1. Tighten all fasteners

2. Refer to engine solutions (above)

3. Normally due to belt/pulley break in period.

Refer to Belt Tension Adjustment section.

Tines will not rotate 1. Debris interfering with tines

2. Tines loose

3. Improper drive cable adjustment

4. Damaged drive belts

1. Remove debris from around tines

2. Replace tine bolts and nuts

3. Refer to “Belt Tension Adjustment” section to

decrease belt tension

4. Replace drive belts

Tines continue to rotate when drive

lever is not engaged

1. Improper drive cable adjustment

2. Damaged drive belts

1. Refer to “Belt Tension Adjustment” Section to

decrease belt tension

2. Replace drive belts

Engine will not stop Check switch Replace switch

Tines will not cut properly Tines assembled incorrectly Refer to “Install the Tines” Section

Frequent engine stalling 1. Excessive tilling speed / depth

2. Engine problems (above)

1. Till at a moderate pace. Make multiple passes.

2. Refer to engine solutions (above)

Troubleshooting

• Save all instructions

La page charge ...

Southland SRTT196E Mode d'emploi

Marque: Southland

Modèle: SRTT196E

Catégorie: Mini motoculteurs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Southland SRTT196E User guide
español: Southland SRTT196E Guía del usuario

Documents connexes

Southland SFTT142 Mode d'emploi

Southland SRTT196E Mode d'emploi

Southland SRTT196E Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents