EarthQuake 31043 Le manuel du propriétaire

Marque: EarthQuake

Modèle: 31043

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

31043 Badger™ Front Tine Tiller

GAS/OIL

RATIO

50:1

P/N: 31050

ECN: 12675

REV1: 10/23/19

ENGLISHFRANÇAIS

Get parts or technical assistance online at

www.GetEarthquake.com or call (800) 345-6007

Pièces détachées et assistance technique en ligne à

www.GetEarthquake.com ou composer le (800) 345-6007

Obtenga piezas o asistencia técnica en línea en

www.GetEarthquake.com o llame al (800) 345-6007

Owner’s Manual

Manuel de l’utilisateur

Badger™

Front Tine Tiller

Model Numbers, Numéros de modèle:

31043

Operator’s Manual

BADGER Front Tine Tiller

2 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

INTRODUCTION

Thank you for purchasing the BADGER Tiller from Earthquake®. We have worked to ensure that this tiller meets the highest stan-

dards for usability and durability. With proper care, your tiller will provide many years of service.

Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the

product and this document at any time without prior notice.

CONTENTS

Introduction/Contents/Registration and Service ............................................................................................................................................................. 2

Warnings and Safety Precautions .......................................................................................................................................................................................3-6

Safety Decals ..................................................................................................................................................................................................................................7

Hazard Symbols and Meanings ...............................................................................................................................................................................................8

Features ...........................................................................................................................................................................................................................................9

Unpacking and Assembly ................................................................................................................................................................................................ 10-12

Controls and Operating Symbols/Controls ................................................................................................................................................................ 12-13

Operation ......................................................................................................................................................................................................................................14

Maintenance .........................................................................................................................................................................................................................15-17

Storage ...........................................................................................................................................................................................................................................17

Troubleshooting and Repair ................................................................................................................................................................................................... 18

OWNERSHIP RECORDS

Owner’s Name:

Owner’s Address:

City: State/Province: Zip Code/Postal Code:

Model Number: Serial Number:

Date of Purchase:

Notes:

Record the product model number and serial number in the space

provided for easy reference when ordering parts or requesting

technical support. Excluding emissions-related warranty items, the

warranty is valid only if the completed registration is received by

Ardisam within 30 days of purchase. (SEE WARRANTY SECTION FOR

MORE INFORMATION) You can register your warranty online by vis-

iting www.getearthquake.com, or by mailing it to: Ardisam, 1160

8th Avenue, Cumberland, WI 54829. You may also call our Custom-

er Service department at (800) 345-6007 Mondays through Fridays

from 8 a.m. to 5 p.m. CST.

Read and keep this manual for future reference. This manual contains important information on SAFETY, ASSEMBLY, OP-

ERATION, AND MAINTENANCE. The owner must be certain that all the product information is included with the unit. This

information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to

make sure state laws and other laws are followed. All persons to whom rent/loan this unit must have access to and under-

stand this information. This manual should remain with the product even if it is resold.

Registration and Service

Serial

Number

Decal

Operator’s Manual

BADGER Front Tine Tiller

3For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

WARNINGS AND SAFETY PRECAUTIONS

Owner’s Responsibility

Accurate assembly and safe and eective use of the machine is

the owner’s responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the machine according to directions and

schedule included in this Earthquake® operator’s

manual.

• Ensure that anyone who uses the machine is familiar

with all controls and safety precautions.

Special Messages

Your manual contains special messages to bring attention to

potential safety concerns, machine damage as well as helpful

operating and servicing information. Please read all the infor-

mation carefully to avoid injury and machine damage.

NOTE: General information is given throughout the

manual that may help the operator in the

operation or service of the machine.

THIS SYMBOL POINTS OUT IMPORTANT

SAFETY INSTRUCTIONS WHICH IF NOT

FOLLOWED COULD ENDANGER YOUR

PERSONAL SAFETY. READ AND FOLLOW ALL

INSTRUCTIONS IN THIS MANUAL BEFORE

ATTEMPTING TO OPERATE THIS EQUIPMENT.

Before Operating Equipment:

Please read this section carefully. Read entire operating and

maintenance instructions for this product. Failure to follow in-

structions could result in serious injury or death. Operate the

machine according to the safety instructions outlined here and

inserted throughout the text. Anyone who uses this machine

must read the instructions and be familiar with the controls.

Intended Use / Foreseeable Misuse

IMPORTANT: This is a motorized rotary tiller that works the

soil by means of rotating tines. It is pedestrian-controlled, but

not self-propelled, with a gasoline-fueled internal combustion

engine to power the tines. It shall not be used for any other

purpose.

DANGER

SRT CRT

WARNING

WARNING INDICATED A HAZARD WHICH, IF NOT

AVOIDED, COULD RESULT IN DEATH OR SERIOUS

INJURY AND/OR PROPERTY DAMAGE.

CAUTION

CAUTION INDICATES A HAZARD WHICH, IF NOT

AVOIDED, COULD RESULT IN PERSONAL INJURY AND/

OR PROPERTY DAMAGE.

DANGER

DANGER INDICATES A HAZARD WHICH, IF NOT

AVOIDED, CERTAINLY WILL RESULT IN DEATH OR

SERIOUS INJURY AND/OR PROPERTY DAMAGE.

WARNING

YOU MUST READ, UNDERSTAND AND COMPLY WITH

ALL SAFETY AND OPERATING INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO SETUP AND

OPERATE YOUR MACHINE.

FAILURE TO COMPLY WITH ALL SAFETY AND

OPERATING INSTRUCTIONS CAN RESULT IN LOSS OF

MACHINE CONTROL, SERIOUS PERSONAL INJURY TO

YOU AND/OR BYSTANDERS, AND RISK OF EQUIPMENT

AND PROPERTY DAMAGE. THE TRIANGLE IN THE TEXT

SIGNIFIES IMPORTANT CAUTIONS OR WARNINGS

WHICH MUST BE FOLLOWED.

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER

REPRODUCTIVE HARM.

IMPORTANT

IMPORTANT INDICATES HELPFUL INFORMATION FOR

PROPER ASSEMBLY, OPERATION, OR MAINTENANCE

OF YOUR EQUIPMENT.

NOTICE

NOTICE INDICATES YOUR EQUIPMENT CAN BE

DAMAGED IF THE SAFETY INSTRUCTIONS THAT

FOLLOW THIS SIGNAL WORD ARE NOT OBEYED.

Operator’s Manual

BADGER Front Tine Tiller

4 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

GENERAL SAFETY RULES

• Read, understand, and follow all instructions on the

machine and in the manual(s). Be thoroughly familiar with

the controls and the proper use of the machine before

starting.

• Use this equipment for its intended purpose only.

• Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments or

accessories.

• Do not put hands or feet near or under rotating parts.

• Only allow responsible individuals who are familiar with the

instructions to operate the machine. Do not allow children

to operate this machine. Do not allow adults to operate the

machine without proper instruction.

• Thoroughly inspect the area where the machine is to be

used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury

or property damage. Stay away from breakable objects,

such as house windows, automobiles, greenhouses, etc.

• Wear appropriate clothing such as a long-sleeved shirt

or jacket. Also wear long trousers or slacks. Do not wear

shorts. Never wear sandals, sneakers or open shoes, and

never operate the machine with bare feet.

• Do not wear loose clothing or jewelry. They can get caught

in moving parts. Always keep hands, feet, hair and loose

clothing away from any moving parts on engine and

machine.

• Always wear safety goggles or safety glasses with side

shields when operating the machine to protect your eyes

from foreign objects which can be thrown from the unit.

Always wear a protective hearing device.

• Always wear work gloves and sturdy footwear. Wear

footwear that will improve footing on slippery surfaces.

Leather work shoes or short boots work well for most

people. These will protect the operator’s ankles and shins

from small sticks, splinters, and other debris.

• It is advisable to wear protective headgear to prevent the

possibility of being struck by small ying particles, or being

struck by low hanging branches, twigs, or other objects

which may be unnoticed by the operator.

• Do not operate the machine without proper guards or

other safety protective devices in place.

• See manufacturer’s instructions for proper operation and

installation of accessories. Only use accessories approved

by the manufacturer.

• Operate only in daylight or good articial light.

• Do not operate product when fatigued or under the

inuence of alcohol, drugs or other medication which

can cause drowsiness or aect your ability to operate this

machine safely.

• Never operate machine in wet grass. Always be sure of

your footing; keep a rm hold on the handle and walk;

never run.

• Watch for trac when operating machine near, or when

crossing roads.

• If the equipment should start to vibrate abnormally,

stop the engine (motor), ip the ON/OFF switch to the

OFF position. Check immediately for cause. Vibration is

generally a warning of trouble. If the noise or vibrations of

the machine increase, stop immediately and perform an

inspection.

• Never leave the machine unattended when the engine is

running. Flip the ON/OFF switch to the OFF position.

• Regularly inspect the machine. Make sure parts are not

bent, damaged, or loose.

• Temperature of muer and nearby areas may exceed 150°

F (65° C). Allow muer and engine areas to cool before

touching. Never pick up or carry the machine while the

engine is running.

• Prolonged exposure to noise and vibration from gasoline

engine-powered equipment should be avoided. Take

intermittent breaks and/or wear ear protection from engine

noise as well as heavy work gloves to reduce vibration in the

hands.

• Keep all screws, nuts, and bolts tight.

• Do not transport the machine from one place to another

with the engine running.

• When moving the packaged machine, always do so with a

partner.

• Check local regulations for age restrictions on use of this

machine.

Product-Specic Safety Rules

• Do not till above underground utilities, including water

lines, gas lines, electric cables, or pipes. Do not operate the

machine on terrain/soil with large rocks and foreign objects

which can damage the equipment.

• After striking a foreign object, stop the engine. Flip the ON/

OFF switch to the OFF position. Inspect the machine for

damage. If damaged, repair before starting and operating

the machine.

• The tines of the tiller should not rotate when the drive

control lever is released into the neutral position. If it does

rotate when in neutral, contact Earthquake® Customer

Service for instruction.

• If an object becomes lodged in the tines, ip the ON/OFF

switch to the OFF position, allow to cool before attempting

to remove the foreign object.

• Pulleys and belts should be kept free of oil or other

moisture for ecient operation.

• Disengage all clutches and leave control lever in the neutral

position before starting the engine.

Operator’s Manual

BADGER Front Tine Tiller

5For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

ENGINE SAFETY PRECAUTIONS

If your product comes with a separate engine

manual, be sure to read and follow all safety and

warning precautions outlined there, in addition

to any in this manual.

Preventing Carbon Monoxide Poisoning

• Always start and run engine outdoors. Do not start or run

engine in an enclosed area, even if doors or windows are

open.

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

• Never run engine outdoors in a poorly ventilated area

where the exhaust fumes may be trapped and not easily

taken away. (Examples include: in a large hole or areas

where hills surround your working area.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

• Always run the engine with the exhaust and muer

pointed in the direction away from the operator.

• Never point the exhaust muer towards anyone. People

should always be many feet away from the operation of the

engine and its attachments.

• Do not change the engine governor settings or over-speed

the engine.

Gasoline Fires and Handling Fuel Safely

Use extra care in handling gasoline and other fuels. They are

ammable and vapors are explosive.

• When storing extra fuel be sure that it is in an appropriate

container and away from any re hazards.

• Prevent re and explosion caused by static electric

discharge. Use only nonmetal, portable fuel containers

approved by the Underwriter’s Laboratory (U.L.) or the

American Society for Testing & Materials (ASTM).

• Never remove the fuel cap or add fuel with the engine

running. Stop engine and allow to cool before lling.

• Do not smoke while using engine or product.

• Never drain fuel from engine in an enclosed area.

• Always ll fuel tank outside in a well ventilated area. Never

ll your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.) Never

ll tank near appliances with pilot lights, heaters, or other

ignition sources. If the fuel has to be drained, this should

be done outdoors. The drained fuel should be stored in a

container specically designed for fuel storage or it should

be disposed of carefully.

• Always wipe up excess (spilled) fuel from engine before

starting. Clean up spilled fuel immediately. If fuel is spilled,

do not start the engine but move product and fuel container

from area. Clean up spilled fuel and allow to evaporate and

dry after wiping and before starting.

• Allow fuel fumes/vapors to escape from the area before

starting engine.

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

• Never smoke while relling engine fuel tank.

• Do not store engine with fuel in fuel tank indoors. Fuel and

fuel vapors are highly explosive.

Preparation

• Dress appropriately when operating the tiller. Always wear

sturdy footwear. Never wear sandals, sneakers or open

shoes, and never operate the tiller with bare feet. Do not

wear loose clothing that might get caught in moving parts.

• Carefully inspect the area to be tilled and remove all foreign

objects. Do not till above underground water lines, gas

lines, electric cables, or pipes. Do not operate the tiller in

soil with large rocks and foreign objects which can damage

the equipment.

• Disengage all clutches and leave control lever in the neutral

position before starting the engine.

• Handle fuel with care; it is highly ammable.

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot engine.

c. Fill fuel tank outdoors with extreme care. Never ll fuel

tank indoors.

d. Replace gasoline cap securely and clean up spilled fuel

before restarting.

WARNING

ENGINES GIVE OFF CARBON MONOXIDE, AN

ODORLESS, COLORLESS, POISONOUS GAS. CARBON

MONOXIDE MAY BE PRESENT EVEN IF YOU DO NOT

SMELL OR SEE ANY ENGINE EXHAUST. BREATHING

CARBON MONOXIDE CAN CAUSE NAUSEA, FAINTING

OR DEATH, IN ADDITION TO DROWSINESS, DIZZINESS

AND CONFUSION.

IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK

FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

Operator’s Manual

BADGER Front Tine Tiller

6 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

OPERATION

• Do not operate tiller under the inuence of alcohol or

drugs.

• Never operate tiller without guards, covers, and hoods in

place.

• Keep hands, feet, and clothing away from rotating parts.

Keep clear of tiller tines at all times.

• Tines rotate when tiller is engaged; tines rotate when the

drive safety control lever is pulled down. Releasing the

drive safety control lever to neutral stops the tines.

• Use extreme caution when operating on or crossing gravel

drives, walks, or roads. Stay alert for hidden hazards or

trac.

• After striking a foreign object, stop the engine, remove the

wire from the spark plug, thoroughly inspect the tiller for

any damage, and repair the damage before restarting and

operating the tiller.

• If vegetation clogs the tines, stop the engine and

disconnect the spark plug wire before removing vegetation

by hand.

• If the unit should start to vibrate abnormally, stop the

engine and check immediately for the cause. Vibration is

generally a warning of trouble.

• Do not run the engine indoors; exhaust fumes are deadly.

• Do not overload the machine capacity by attempting to till

too deep at too fast of a rate.

• Never operate the tiller without good visibility or light.

• Be careful when tilling in hard ground. The tines may catch

in the ground and propel the tiller forward. If this occurs, let

go of the handle bars and do not restrain the machine.

• Take all possible precautions when leaving the machine

unattended. Disengage control lever, stop the engine, wait

for all moving parts to stop, and make certain guards and

shields are in place.

• When leaving the operating position for any reason:

- Shut o the engine.

- Wait for all moving parts to stop.

MAINTENANCE AND STORAGE

• Keep machine, attachments and accessories in safe

working condition.

• Check shear bolts, engine mounting bolts and other bolts

at frequent intervals for proper tightness to be sure the

equipment is in safe working condition.

• To prevent accidental starting, always disconnect and

secure the spark plug wire from the spark plug before

performing tiller maintenance.

• Never run the engine indoors. Exhaust fumes are deadly.

• Always allow muer to cool before lling the fuel tank.

• Never store equipment with gasoline in the tank inside

a closed building where fumes may reach an open ame

or spark. Allow the engine to cool before storing in any

building.

• Always refer to the operator’s guide instructions for

important details if the tiller is to be stored for an extended

period.

WARNING

THE RIGHT AND LEFT SIDES

OF YOUR ROTOTILLER ARE

DETERMINED FROM THE

OPERATING POSITION AS

YOU FACE THE DIRECTION

OF FORWARD TRAVEL.

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.

YOU MUST ADD ENGINE OIL BEFORE STARTING

ENGINE.

L R

WARNING

HOT GASES ARE A NORMAL BYPRODUCT OF A

FUNCTIONING INTERNAL COMBUSTION ENGINE.

FOLLOW ALL SAFETY INSTRUCTIONS TO PREVENT

BURNS AND FIRES.

DO NOT ALTER/MODIFY ENGINE:

NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR PRODUCT, YOU MUST ALWAYS FLIP THE

ON/OFF SWITCH TO THE OFF POSITION.

Operator’s Manual

BADGER Front Tine Tiller

7For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Part No. 17047

PINCH POINT WARNING

Tail Mount Decal

Part No. 17052

MOVING PARTS WARNING

Frame Near Belt Decal

Part No. 17050

TINES DANGER/OPERATION

Hood Decal

Part No. 17049

MULTI INJURY WARNING

Hood Decal

SAFETY DECALS

This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an

industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to

operate this equipment safely and eectively, we have placed several safety labels on the tiller to remind you of this important

information while you are operating the unit.

These important safety labels are illustrated below, and are shown here to help familiarize you with the location and content of

the safety messages you will see as you perform normal tilling operations. Please review these decals now, and if you have any

questions regarding its meaning or how to comply with these instructions, reread the complete safety instruction text in this

manual. For additional questions call Earthquake® Customer Service.

15698

Part No. 15698

DECAL PICTORIAL LEVER

CLUTCH ENGAGEMENT

Right Handle Bar and Drive

Control Lever

When starting engine,

place free hand here.

Pour démarrer le moteur,

placer le main libre ici.

17918

Part No. 17918

DECAL PLACE FREE HAND HERE

Left Handle Bar

Part No. 17920

CORRECT TINE INSTALLATION

Operator’s Manual

BADGER Front Tine Tiller

8 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

HAZARD SYMBOLS AND MEANINGS

A: Warning!

B: Avoid Injury From Rotating Tines.

C: Read Owner’s Manual Before Operating Machine.

D: Remove Objects that Could Be Thrown By This Machine.

E: Dangerous Moving Parts.

F: Be Aware of Moving and Rotating Parts.

G: Wear Ear and Eye Protection At All Times.

H: Do Not Service or Adjust Moving Parts Unless Engine is Stopped and Spark Plug

Wire is Disconnected.

I: Dress Appropriately And Wear Sturdy Footwear.

J: Toxic Fumes—Do Not Operate in Unventilated Areas.

K: Hot Surfaces.

L: Fire Hazards.

M: Do Not Use In Thunderstorms—For severe weather, stop operation of this

machine and seek shelter.

N: Team Lift—For your safety, always have at least two people when lifting this

machine.

O: Do Not Till Above Underground Utility Lines And Pipes.

P: Do Not Operate When Children Or Others Are Around.

D E F

G H

O P

Operator’s Manual

BADGER Front Tine Tiller

9For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

FEATURES

The advantage of the Earthquake® BADGER gear drive Front Tine Rototiller, over other tillers, is the

exclusive hinged tail mount, wheel and drag stake assembly. This feature gives the tiller its stability and

versatility. For easy transport and quick turning in the garden, fold the wheels under the engine. During

operation, the wheels unfold back and the drag stake folds down. The long length between the tines and

the drag stake make this the most comfortable handling front tine tiller on the market. SEE FIGURE 1

TRANSPORT POSITION OPERATING POSITION

DRIVE SAFETY

CONTROL LEVER

KNOBBY

COMFORT

GRIPS

3-POSITION

HANDLE

BAR HEIGHT

ADJUSTMENT

LARGE 2-POSITION

WHEELS

ADJUSTABLE

DRAG STAKE

TINE SHIELD

3-WAY ADJUSTABLE

TINE WIDTHS

ADJUSTABLE

FORWARD

CABLE

BUMPER

FRONT

BELT

COVER

HINGED CAST-IRON TAIL MOUNT

DURABLE FORGED TINES

FIGURE 1

Operator’s Manual

BADGER Front Tine Tiller

10 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

UNPACKING AND ASSEMBLY

Carton Contents

• Front Tine Rototiller

• Parts Bag (with manuals and assembly hardware parts packet)

• Parts Box (with outer tines, wheel axle, and drag stake)

• 2x Wheels

• Handlebar Assembly

• Tine Shield

• Bottle of Viper® 4-Cycle Oil

Tools Required for Assembly

• Utility knife or box cutter

• 2x 10 mm Wrench

• 2x 13 mm Wrench

NOTE: Socket head wrench may make assembly easier,

but is not necessary.

ASSEMBLY

1. a. Open top of carton and remove handlebar assembly,

wheels, parts bag, tine shield, and bottle of oil.

b. Parts Packet contains:

• 4 - Bolts M8 X 1.25 X 20MM

• 2 - Hairpin 2.5 Dia. X 35MM

• 1 - Pin Lock 8 X 40MM

• 4 - Washers M8 X 24 X 2.0MM

• 2 - Bolts M8 X 1.25 X 45

• 6 - Nut M8 Nylock

• 2 - Washer 12MM

• 4 - Bolts M6 X 1.0 X 16MM

• 4 - Nut M6 Nylock

• 1 - Drag Stake Handle Assembly (Incl. M6 Bolt & Nut)

NOTE: Plastic side of Nylock nut must face away from

bolt head during assembly. SEE FIGURE 8

2. Cut all four corners of box so it lies at on the ground.

3. Pull out parts box and remove contents.

4. Assemble axle to lower tail mount. Install wheels on each

end of axle; install 12 MM washers onto axle against wheels;

insert hairpins into holes in axle to keep washers and

wheels in place. SEE FIGURE 3

5. Install tine shield using four M6 bolts and four M6 nylock nuts.

Line up slots on both sides of shield and insert both bolts and

nuts in place before fully tightening. SEE FIGURE 4

NOTE: Dirt shield must be between engine mount deck

and tine shield.

6. Assemble tines to unit.

a. Assemble outer tines to unit using two M8 bolts and

two M8 nylock nuts. The arrow on the tines must point

in the direction of forward rotation.

b. Outside tines have two positions- wide 21" and narrow

16". For narrow width, assemble with short side of tine

holder pipe towards center of machine. SEE FIGURE 5

c. For wide width, move the left tine to the right side and

right tine to the left side. Assemble with the long side

of tine pipe towards machine, making sure arrow on the

tines are pointing in the direction of forward rotation.

SEE FIGURE 6

FIGURE 2

Tail mount casting allows tiller to be in two dierent positions:

working and transport. When transitioning from working

position into transport position, or vice versa, be careful of the

breach between the upper and lower tail mount casting to avoid

pinching hazards.

Working Position

Transport Position

CAUTION

HANDLE ROTOTILLER WITH CARE. DO NOT DAMAGE

THROTTLE CABLE WHEN TRANSPORTING OR

OPERATING.

IMPORTANT

IT IS RECOMMENDED THAT TWO PEOPLE ASSEMBLE

ROTOTILLER TOGETHER. ASSEMBLING ROTOTILLER

ALONE MAY MAKE ASSEMBLY MORE DIFFICULT AND

INCREASE RISK OF INJURY.

WARNING

DO NOT LIFT ROTOTILLER FROM CARTON. ROTOTILLER

IS HEAVY AND CAN CAUSE INJURY. CUT BOX AWAY

FROM ROTOTILLER TO ACCESS MACHINE AND PARTS.

WARNING

KEEP HANDS AND FEET AWAY FROM TAIL MOUNT

CASTING. FAILURE TO DO SO MAY RESULT IN SERIOUS

INJURY. SEE FIGURE 2

Operator’s Manual

BADGER Front Tine Tiller

11For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

7. a. Assemble the upper handle bar assembly onto the

lower loop mount using four M8 bolts, four M8 at

washers and four M8 locknuts. The handlebar as well as

the bolt should go on the outer side of the lower loop

mount, while the washer and nut should be placed on

the inside. SEE FIGURES 7 & 8

b. The upper two bolts can be assembled through one of

three hole positions depending on the user’s preferred

handle bar height (low, middle, high). For the highest

height, insert bolt into the most forward hole. For the

lowest height, insert bolt into the most rear hole. SEE

FIGURE 7

8. Insert depth regulator/drag stake through bottom opening

in lower tail mount and secure with lock pin. Assemble

drag stake handle onto drag stake using accompanying M6

Bolt and Nut. SEE FIGURE 9

FIGURE 4

Dirt

Shield

Tine Shield

Engine

Mount Deck

High

Position

Medium

Position

Low

Position

Upper Bolt

Lower Bolt

Lower Loop Mount

FIGURE 7

FIGURE 3

Lower Tail

Mount

Washer

Wheel

Hairpin

FIGURE 5

FIGURE 6

Narrow

Tine

Width

Wide Tine

Width

Nylock

Nut

FIGURE 8

Drag Stake

FIGURE 9

Lock Pin

Drag Stake

Operator’s Manual

BADGER Front Tine Tiller

12 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Fill Engine Crankcase

1. Add oil according to engine manual. Do not overll.

Use a clean, high quality detergent oil. Use no special

additives with recommended oils. Do not mix oil with

gasoline. Oil level must be full. Check the oil level by

checking the engine’s oil dipstick if provided, or by

removing oil ll plug. Oil level should be up to the

bottom of the ll plug opening.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

CONTROL AND OPERATING SYMBOLS

FIGURE 10 shows common control and operating symbols

that may be found on the unit or in this manual. Before you

operate your unit, learn and understand the purpose for each

symbol.

Choke

On/O Fuel Shuto

CONTROLS

Drive Safety Control Lever

Pulling down on the drive safety control lever engages the

tines. Releasing the drive safety control lever disengages the

tines to a neutral position.

Belt Tension Adjustment

Proper belt tension is critical for good performance. After 30

minutes of operation, all cables may have to be adjusted due

to initial stretch. Thereafter, check tension after every two

hours of operation.

FIGURE 10

1. To increase belt tension, loosen upper jam nut in 1/8"

increments while holding lower jam nut in place.

SEE FIGURE 11

2. Check adjustment and instructions under “Check Belt

Tension” section.

This procedure can be repeated until conduit adjustment

bolts have no more adjustment left. If no more adjustment

can be made, belt may have to be replaced.

Depth Regulator Drag Stake

To Adjust Tilling Depth:

1. Remove lock pin.

2. Raise or lower the depth regulator. The lower the depth

regulator, the deeper the tilling depth.

3. Align hole in depth regulator lever with hole in depth

regulator bracket and replace lock pin.

SEE FIGURE 9 (page 11)

UPPER

JAM

NUT

LOWER

JAM

NUT

FIGURE 11FIGURE 11

WARNING

THIS INFORMATION IS PROVIDED HERE ONLY TO

INTRODUCE THE CONTROLS. DO NOT START THE

ENGINE AT THIS TIME. STARTING AND OPERATING

INSTRUCTIONS ARE GIVEN IN THIS MANUAL. PLEASE

READ THIS SECTION AND ALL OPERATING AND

SAFETY INSTRUCTIONS BEFORE STARTING YOUR

TILLER.

• AS A SAFETY PRECAUTION, THE DRIVE SAFETY

CONTROL LEVER WILL NOT LOCK IN THE FORWARD

POSITION.

• TO STOP THE TINES AT ANY TIME, RELEASE THE

DRIVE SAFETY CONTROL LEVER.

• ENGINE SHOULD BE OFF BEFORE ADJUSTING ANY

CONTROLS.

• DO NOT ADJUST TILLING DEPTH UNLESS DRIVE

SAFETY CONTROL LEVER IS RELEASED TO THE

NEUTRAL POSITION.

WARNING

THE RIGHT AND LEFT SIDES

OF YOUR ROTOTILLER ARE

DETERMINED FROM THE

OPERATING POSITION AS

YOU FACE THE DIRECTION

OF FORWARD TRAVEL.

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.

YOU MUST ADD ENGINE OIL BEFORE STARTING

ENGINE.

L R

Operator’s Manual

BADGER Front Tine Tiller

13For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

DANGER

DO NOT START YOUR TILLER UNTIL YOU HAVE

READ AND UNDERSTAND THIS MANUAL AND THE

SECTIONS IN THIS MANUAL COVERING SAFETY AND

OPERATION.

ALWAYS PERFORM THE PRESTART INSPECTION

CHECKLIST BEFORE STARTING THE ENGINE.

PRACTICE OPERATING THE CONTROLS AND TILLER

WITH TINES OUT OF GROUND BEFORE BEGINNING

TO TILL. IT IS IMPORTANT THAT YOU KNOW HOW TO

USE THE TILLER PROPERLY: KEEP CONTROL AT ALL

TIMES, STOP THE TINE FROM TURNING, AND STOP

THE ENGINE IF NECESSARY. IF YOU DO NOT KNOW

HOW TO DO THESE THINGS, READ THE CONTROLS

AND SAFETY SECTIONS BEFORE PROCEEDING.

ALWAYS MAINTAIN CONTROL OF YOUR TILLER. ONLY

OPERATE TILLER IN SOIL CONDITIONS THAT ARE

CONDUCIVE TO MAINTAINING CONTROL OF THE

TILLER. DO NOT OPERATE TILLER IN CONDITIONS THAT

CONTAIN ROCKS, FOREIGN OBJECTS, OR ANY OTHER

MATERIAL THAT IS NOT SOIL. IF YOUR TILLER BUMPS,

JERKS, OR LURCHES, LET GO OF THE HANDLEBARS

AND THE DRIVE CONTROL LEVER IMMEDIATELY SO

THAT THE TINES STOP TURNING.

CAUTION MUST BE TAKEN WHEN SELECTING TILLING

DEPTH. LOSS OF CONTROL COULD RESULT IF YOU

ATTEMPT TO TILL IN CERTAIN SOIL CONDITIONS WITH

THE DRAG STAKE SET IN TOO HIGH OF A POSITION.

STOP THE ENGINE AND REMOVE SPARK PLUG WIRE

BEFORE REMOVING MATERIAL FROM THE TINES BY

HAND OR ANY OTHER METHOD.

ENGINE AND SURROUNDING PARTS BECOME

EXTREMELY HOT DURING NORMAL OPERATION.

TEMPERATURE OF MUFFLER AND NEARBY AREAS

MAY EXCEED 150°F 66°C. AVOID THESE AREAS.

ALLOW ENGINE TO COOL COMPLETELY BEFORE

TOUCHING THESE HOT SURFACES. THESE AREAS WILL

CAUSE SERIOUS BURN INJURIES IF TOUCHED BEFORE

THE ENGINE HAS COOLED.

ALWAYS KEEP HANDS AND FEET CLEAR OF ROTATING

MACHINE PARTS.

CAUTION

DO NOT USE CHOKE CONTROL TO STOP ENGINE.

BACKFIRE OR ENGINE DAMAGE MAY OCCUR!

TO STOP THE ENGINE AT ANY TIME, MOVE THROTTLE

CONTROL TO THE OFF OR STOP POSITION, OR TURN

THE ON/OFF SWITCH TO OFF.

ALWAYS RELEASE DRIVE SAFETY CONTROL LEVER TO

NEUTRAL POSITION BEFORE ADJUSTING THE DEPTH

OF THE DRAG STAKE.

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.

YOU MUST ADD ENGINE OIL BEFORE STARTING

ENGINE.

Operator’s Manual

BADGER Front Tine Tiller

14 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

Cold Start

1. Push ON/OFF switch to the ON position.

2. Move choke lever to full choke position, if equipped.

3. Pull starting rope out slowly one time and allow to return

normally.

4. Pull starting rope out rapidly and allow rope to return normally.

5. When engine starts, gradually move choke lever to no

choke position, if equipped.

NOTE: The engine installed on the tiller is xed speed

and does not have a throttle control.

Restarting A Warm Engine

Restarting an engine that is already warm from previous run-

ning does not normally require the use of the choke, if one is

equipped.

1. Push ON/OFF switch to the ON position.

2. Pull starting rope out rapidly until engine starts. Allow rope

to return normally. Repeat until engine starts.

Shutting Down

To stop the engine at any time, put the ON/OFF switch to the

OFF position. To stop tines at any time, release the drive safety

control to the neutral position.

Tilling

1. Adjust the depth regulator drag stake to achieve desired

tilling depth.

NOTE: Raise depth regulator lever up one hole at a

time, testing tiller operation after each adjustment.

Raising depth regulator lever too high can result in loss

of control of tiller!

2. Place the tiller in motion by pushing down on the drive

safety control lever; this will engage the tines.

OPERATION

Pre-Start Inspection

1. Make sure all safety guards are in place and all nuts and

bolts are secure.

NOTE: All hardware (nuts, bolts, etc) should be checked

for tightness before each use. Vibration of machine

can cause them to loosen.

2. Check oil level in engine crankcase. See your engine

manual for procedure and specications.

3. Inspect air cleaner for cleanliness. See your engine manual

for procedure.

4. Check the fuel level. Fill the fuel tank no closer than one

inch from top of tank to provide space for expansion. See

your engine manual for fuel recommendations.

5. Be sure spark plug wire is attached and spark plug is

tightened securely.

6. Check position of wheels.

7. Check depth regulator drag stake position.

8. Examine underneath and around engine for signs of oil or

fuel leaks.

9. Inspect fuel hoses for tightness and fuel seepage.

10. Look for signs of engine damage.

11. Remove excessive debris from muer area and recoil

starter.

12. Turn fuel shuto valve to the ON position if engine is

equipped with one.

STARTUP

The ON/OFF switch and choke lever required to cold start

the rototiller are located on the engine and are marked with

ON/OFF and choke control symbols (See Operation Control

Symbols in the Controls and Operating Symbols section of this

manual). SEE FIGURE 12

A description of engine operation and all related precautions

and procedures can be found in the engine manufacturer’s

manual that accompanies the tiller.

WARNING

GASOLINE IS HIGHLY FLAMMABLE AND MUST BE

HANDLED WITH CARE. NEVER FILL THE TANK WHEN

THE ENGINE IS HOT OR RUNNING. ALWAYS MOVE

OUTDOORS TO FILL THE TANK.

ON/OFF

Switch

Choke

Lever

FIGURE 12FIGURE 12

Operator’s Manual

BADGER Front Tine Tiller

15For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

MAINTENANCE

Maintenance Schedule

Your rototiller has been designed and produced by the industry’s leading manufacturer of outdoor power equipment to provide

you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum

performance. Please read this maintenance schedule, and note the recommended care operating intervals to extend the life of

your unit.

Maintenance Operation Page

Before

Each Use

50 hours or

Every Season

Check belt tension 16 X

Change forward belt 16 X

Engine maintenance 17, EM X X

Check oil level/change oil 17, EM X 1

Clean tine axle shaft 17 X X

Lubrication 17 X

EM = See engine manual

1 = Change oil after the rst three to ve hours of use, then after every 50 hours or every season. Change oil

every 25 hours when operating under heavy load or in high temperatures.

SERVICING THE ROTOTILLER

The following information will help you make the necessary

checks and perform the procedures required to follow the

normal care recommendations made for your rototiller unit.

If you prefer, your local authorized dealer can make these

checks and perform the required procedures for you.

Important: Use only approved Earthquake® spare parts.

Spark

Plug

Wire

WARNING

PREVENT ACCIDENTAL STARTING.

ENGINE MUST BE TURNED OFF AND COOL, AND SPARK

PLUG WIRE MUST BE REMOVED AND SECURED FROM

SPARK PLUG BEFORE CHECKING AND ADJUSTING

ENGINE OR EQUIPMENT. ACCIDENTAL ENGINE START

CAN CAUSE SERIOUS INJURY.

Operator’s Manual

BADGER Front Tine Tiller

16 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

BELT MAINTENANCE

Check Belt Tension

Belt tension may decrease over time. It may need to be

adjusted within the rst half hour of operation and should be

checked after every two hours of operation. Proper adjustment

will assure long belt life. Too much or too little belt tension will

cause premature belt failure.

An indication that the belt may need to be adjusted is

a constant buzzing sound that can be heard when the

engagement lever is compressed (see page 18), or a persistant

squealing sound when engaged and under load.

NOTE: A short buzzing noise can be heard when

engagement lever is released. This is normal, caused

by the teeth of the cog belt catching the wire guide,

stopping the rotation of the belt. This does not require

the belt tension to be adjusted.

To check and adjust the belt tension, do as follows:

1. Turn o engine. Engine must be cool.

2. Remove spark plug wire from spark plug and secure.

3. With drive safety control lever in the neutral position,

measure length of the cable spring when in its relaxed

state.

4. Pull down on drive safety control lever and measure length

of spring when extended. Ideal length would be 1/4"

longer. SEE FIGURE 13

5. To adjust, SEE FIGURE 11 and Belt Tension Adjustment

instructions.

Change Belt

1. Turn o engine. Engine must be cool.

2. Remove spark plug wire from spark plug and secure.

3. Remove front belt cover and dirt shield plate from tiller

frame. SEE FIGURE 14

a. Remove the belt from the engine pulley as follows:

• Gently pull the engine recoil rope to rotate the pulley.

• With the pulley turning, force the belt out of the

V-groove.

• Slide the belt free of the engine pulley.

• Pull the belt down and out of the way.

• Push the belt forward and out the front of the machine.

b. Install new belt as follows:

• Place belt in transmission pulley groove.

• Gently pull the engine recoil rope to rotate the engine

pulley while forcing the belt into the V-groove.

4. Reinstall front belt cover and dirt shield plate onto tiller frame.

5. Check and readjust belt tension if necessary.

6. Attach spark plug wire.

BELT REPLACEMENT P/N: 22633

Front

Belt

Cover

Dirt Shield Plate

FIGURE 14

FIGURE 13

ÉTIREMENT DE

6 MM (1/4 PO)

IMPORTANT

CHECK BELT TENSION REGULARLY. TOO MUCH OR

TOO LITTLE TENSION WILL CAUSE PREMATURE BELT

FAILURE AND DAMAGE TO EQUIPMENT.

Operator’s Manual

BADGER Front Tine Tiller

17For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

ENGINE MAINTENANCE

Refer to the engine manual included in your parts bag for

information on engine maintenance. Your engine manual pro-

vides information and a maintenance schedule for performing

the following tasks:

1. Check oil level before each use and after every eight hours

of operation.

2. Change oil after rst three to ve hours of operation.

3. Change oil while engine is warm. Rell with new oil of

recommended grade.

4. Check spark plug yearly or every 100 hours of operation.

5. Service air cleaner.

6. Keep engine and parts clean.

7. Check engine and equipment often for loose nuts and

bolts; keep all hardware tightened.

Check or Fill Engine Crankcase

1. Add oil according to engine manual. Do not overll. Use

a clean, high-quality 4-cycle engine oil. Use no special

additives with recommended oils. Do not mix oil with

gasoline. Oil level must be full. Check the oil level by

checking the engine’s oil dipstick.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

Clean Tine Axle Shaft

1. Turn o engine. Engine must be cool.

2. Remove spark plug wire and secure from spark plug.

3. Remove all vegetation, string, wire, and other material that

may have accumulated on the axle between the inside set

of tines and the seal on the transmission housing.

4. Replace spark plug wire.

Lubrication

Proper lubrication of moving mechanical parts is critical for

proper care and maintenance. Oil the moving parts using a

30-weight oil.

STORAGE

Prepare for Storage

Follow the steps below to prepare your tiller for storage. Read

your engine manual for detailed instructions on preparing the

engine for storage.

1. Protect wheels and axles from rust:

• Coat the axles lightly with axle grease.

2. Drain fuel system completely following engine manufacturer’s

instructions or add fuel stabilizer to prevent fuel from

gumming up during extended storage period. Run engine

for at least 5 minutes to distribute fuel stabilizer mixture

throughout entire fuel system.

3. While engine is still warm, drain the oil from the engine. Rell

with fresh oil that is recommended in engine manual.

4. Clean external surfaces, engine and cooling fan.

5. Remove spark plug; pour one ounce of SAE 30 oil into spark

plug hole.

6. Plug hole and pull starter cord slowly to distribute oil evenly

in cylinder head area.

7. Reinstall spark plug.

8. Transport unit to a suitable storage location. If you have

chosen to use a fuel stabilizer and have not drained the fuel

system, follow all safety instructions and storage precautions

in this manual to prevent the possibility of re from the

ignition of gasoline fumes. Remember, gasoline fumes can

travel to distant sources of ignition and ignite, causing risk

of explosion and re.

9. If there is any possibility of unauthorized use or tampering,

remove the spark plug and store it in a safe place before

storing the rototiller unit. Be sure to plug the spark plug hole

to prevent foreign material from entering.

WARNING

PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE

TURNED OFF AND ALLOWED TO COOL, AND SPARK

PLUG WIRE MUST BE DISCONNECTED AND SECURED

BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.

FAILURE TO COMPLY WITH THIS SAFETY REQUIREMENT

CAN RESULT IN SERIOUS PERSONAL INJURY TO YOU

OR BYSTANDERS.

DO NOT STORE TILLER IN AN UNVENTILATED AREA

WHERE FUEL FUMES MAY REACH FLAME, SPARKS,

PILOT LIGHTS OR AN IGNITED OBJECT. DRAIN FUEL

OUTDOORS AWAY FROM ANY IGNITION SOURCES.

USE ONLY APPROVED FUEL CONTAINERS.

CAUTION

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU

MUST ADD ENGINE OIL BEFORE STARTING ENGINE.

ENGINE CAN OVERHEAT AND BECOME DAMAGED IF

DEBRIS BLOCKS THE COOLING SYSTEM OR ROTATING

SCREEN.

NEVER RUN ENGINE WITHOUT COMPLETE AIR CLEANER

INSTALLED ON ENGINE.

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE

DAMAGE TO THE ENGINE AND VOID YOUR WARRANTY.

Operator’s Manual

BADGER Front Tine Tiller

18 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

PROBLEM REMEDY/ACTION

Engine will not start • Add gas to gas tank.

• Connect spark plug wire to spark plug.

• ON/OFF switch must be turned ON and engine choked

for a cold start (if equipped with a choke).

Engine runs rough, oods during operation • Clean or replace air cleaner.

Engine is hard to start • Drain old fuel and replace with fresh. Use gas stabilizer

at end of season.

• Make sure spark plug wire is securely attached to spark

plug.

• Drive safety control lever must be released to neutral to

start the engine.

Engine misses or lacks power • Raise the tines for shallow tilling by raising the depth

regulator drag stake.

• Clean or replace air cleaner.

• Improper carburetor adjustment, take to authorized

engine service center.

• Replace spark plug and adjust gap.

• Drain and rell gas tank with fresh fuel.

Tiller moves forward during starting • Drive safety control lever must be released to neutral to

start the engine.

• Check belt tension.

Tiller is dicult to control when tilling

(Machine jumps or lurches forward)

• Lower the depth regulator drag stake for greater

resistance and control of the machine.

Belts squeal in forward operation • Check belt tension and adjust if necessary.

Constant buzzing sound is heard while engagement lever is com-

pressed

• Fully compress engagement lever

• Properly space wire guide from idler pulley to clear belt

• Check belt tension and adjust if necessary.

NOTE: If engagement lever is fully compressed, wire

guide is properly adjusted, and cable has reached

full adjustment and buzzing persists, the belt may be

stretched and may need to be replaced. *

Excessive heat build up in transmission/tine area during tilling • Remove vegetation.

• Check transmission uid and ll if needed.

TROUBLESHOOTING AND REPAIR

Troubleshooting Guide

While normal care and routine maintenance will extend the life of your rototiller, prolonged or constant use may eventually

require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most

common problems, causes and remedies.

* Please contact 800-345-6007 for service parts

Manuel de l’utilisateur

Motoculteur à dents avant BADGER

19Pour plus de renseignements, visiter notre site Web à www.getearthquake.com ou composer le 800-345-6007 L-V 8h-17h HNC

INTRODUCTION

Merci d’avoir acheté le motoculteur BADGER d’Earthquake®. Nous nous sommes attachés à ce que ce motoculteur réponde aux plus hautes

normes d’utilisation et de durabilité. Moyennant des soins corrects, il orira de nombreuses années de service able.

Lire ce manuel en entier avant de l’installer et de l’utiliser. Earthquake® se réserve le droit de changer, modier ou améliorer ce produit

et cette documentation à tout moment sans préavis.

SOMMAIRE

Introduction / Sommaire / Enregistrement et service après-vente .....................................................................................................................................................19

Avertissements et mesures de précaution ..............................................................................................................................................................................................20-23

Autocollants de sécurité ...................................................................................................................................................................................................................................... 24

Symboles de sécurité et signications ...........................................................................................................................................................................................................25

Caractéristiques ......................................................................................................................................................................................................................................................26

Déballage et assemblage ..............................................................................................................................................................................................................................27-29

Symboles de commande et de fonctionnement / Commandes ..................................................................................................................................................... 29-30

Utilisation .................................................................................................................................................................................................................................................................. 31

Entretien ..............................................................................................................................................................................................................................................................32-34

Entreposage .............................................................................................................................................................................................................................................................34

Dépannage et réparation .................................................................................................................................................................................................................................... 35

RENSEIGNEMENTS SUR LE PROPRIÉTAIRE

Nom du propriétaire:

Adresse du propriétaire:

Ville : État/Province: Code postal:

Numéro de modèle: Numéro de série:

Date d’achat:

Notes:

Consigner le numéro de modèle et le numéro de série du produit dans

l’espace prévu pour y accéder facilement lors des commandes de pièces

détachées ou des demandes d’assistance technique. À l’exception des

articles couverts par la garantie sur le contrôle des émissions, la garantie

est valable uniquement si l’enregistrement dûment rempli est reçu par

Ardisam dans les 30 jours après l’achat. (POUR PLUS DE RENSEIGNEMENTS,

VOIR LA SECTION SUR LA GARANTIE.) L’enregistrement de la garantie peut

se faire en ligne à www.getearthquake.com ou par courrier à: Ardisam,

1160 8th Avenue, Cumberland, WI 54829, États-Unis. Il est aussi possible

d’appeler notre Service après-vente au (800) 345-6007 du lundi au

vendredi de 8h00 à 17h00 HNC.

Lire ce manuel et le conserver pour toute consultation ultérieure. Ce manuel contient des renseignements importants sur la SÉCURITÉ,

l’ASSEMBLAGE, l’UTILISATION et l’ENTRETIEN. Le propriétaire doit veiller à ce que toute la documentation sur le produit soit fournie

avec l’appareil. Cette documentation comprend le MANUEL, la liste des PIÈCES DE RECHANGE et les GARANTIES. Cette documentation

doit être fournie en vertu de la réglementation en vigueur. Toutes les personnes à qui cette machine est louée/prêtée doivent avoir

accès à ces informations et les comprendre. Le présent manuel doit rester avec le produit, notamment s’il est revendu.

Enregistrement et service après-vente

Autocollant

de numéro

de série

Manuel de l’utilisateur

Motoculteur à dents avant BADGER

20 Pour plus de renseignements, visiter notre site Web à www.getearthquake.com ou composer le 800-345-6007 L-V 8h-17h HNC

AVERTISSEMENTS ET MESURES DE

PRÉCAUTION

Responsabilité du propriétaire

L’assemblage correct et l’utilisation sûre et ecace de la machine

relèvent de la responsabilité de l’utilisateur.

• Lire et respecter toutes les instructions de sécurité.

• Suivre avec attention toutes les instructions d’assemblage.

• Entretenir la machine conformément aux instructions et au

calendrier gurant dans le manuel de l’utilisateur Earthquake.

• S’assurer que quiconque utilise la machine est bien familiarisé

avec toutes les commandes et mesures de précaution.

Messages spéciaux

Ce manuel contient des messages spéciaux attirant l’attention sur des

problèmes de sécurité et dommages potentiels à la machine, ainsi

que des informations utiles sur l’utilisation et l’entretien. Veiller à lire

toutes ces informations avec attention pour éviter les blessures et les

dommages à la machine.

REMARQUE: Des informations générales sont fournies à

travers ce manuel pouvant aider l’opérateur dans

l’utilisation ou l’entretien de la machine.

CE SYMBOLE SIGNALE DES INSTRUCTIONS DE

SÉCURITÉ IMPORTANTES QUI DOIVENT ÊTRE

RESPECTÉES POUR NE PAS METTRE EN DANGER

LA SÉCURITÉ DES PERSONNES. LIRE ET RESPECTER

TOUTES LES INSTRUCTIONS DU MANUEL

AVANT DE TENTER DE FAIRE FONCTIONNER CET

APPAREIL.

Avant d’utiliser la machine:

Veiller à lire cette section avec attention. Lire l’ensemble

des instructions d’utilisation et d’entretien de ce produit. Tout

manquement à respecter ces instructions peut entraîner des

blessures graves ou la mort. Utiliser la machine conformément

aux instructions de sécurité fournies ici et tout au long du manuel.

Quiconque utilise cette machine doit lire les instructions et être

familiarisé avec les commandes.

Emploi prévu / Emploi détourné prévisible

IMPORTANT: Ceci est un motoculteur rotatif motorisé qui travaille le

sol au moyen de fraises en rotation. Il est conçu pour un utilisateur à

pied, mais n’est pas autotracté, avec un moteur à combustion interne

à essence pour entraîner les fraises. Il ne doit être utilisé à aucune

autre n.

DANGER

SRT CRT

AVERTISSEMENT

AVERTISSEMENT INDIQUE UN DANGER QUI, S’IL N’EST PAS

ÉVITÉ, PEUT PROVOQUER LA MORT OU DES BLESSURES

CORPORELLES ET/OU DÉGÂTS MATÉRIELS GRAVES.

ATTENTION

ATTENTION INDIQUE UN DANGER QUI, S’IL N’EST PAS

ÉVITÉ, PEUT PROVOQUER DES BLESSURES CORPORELLES

ET/OU DES DÉGÂTS MATÉRIELS.

DANGER

DANGER INDIQUE UN DANGER QUI, S’IL N’EST PAS ÉVITÉ,

PROVOQUERA IMMANQUABLEMENT LA MORT OU DES

BLESSURES CORPORELLES ET/OU DÉGÂTS MATÉRIELS

GRAVES.

AVERTISSEMENT

VEILLER À LIRE, À COMPRENDRE ET À RESPECTER TOUTES

LES INSTRUCTIONS DE SÉCURITÉ ET D’UTILISATION

FIGURANT DANS CE MANUEL AVANT DE TENTER

D’INSTALLER ET DE FAIRE FONCTIONNER VOTRE MACHINE.

TOUT MANQUEMENT À OBSERVER LES INSTRUCTIONS

DE SÉCURITÉ ET D’UTILISATION PEUT PROVOQUER DES

BLESSURES CORPORELLES GRAVES POUR L’UTILISATEUR

ET D’AUTRES PERSONNES PRÉSENTES ET DES DÉGÂTS

MATÉRIELS. LE TRIANGLE DANS LE TEXTE SIGNIFIE QUE

DES MISES EN GARDES ET AVERTISSEMENT IMPORTANTS

DOIVENT ÊTRE SUIVIS.

AVERTISSEMENT

AVERTISSEMENT PROPOSITION 65 DE CALIFORNIE

L’ÉCHAPPEMENT DU MOTEUR DE CE PRODUIT CONTIENT

DES SUBSTANCES CHIMIQUES DÉCLARÉES RESPONSABLES

DE CANCER, MALFORMATIONS CONGÉNITALES OU

AUTRES ANOMALIES DE LA REPRODUCTION PAR L’ÉTAT DE

CALIFORNIE.

IMPORTANT

IMPORTANT SIGNALE DES INFORMATIONS UTILES

CONCERNANT L’ASSEMBLAGE, L’UTILISATION OU

L’ENTRETIEN DU MATÉRIEL.

AVIS

AVIS INDIQUE QUE LE MATÉRIEL PEUT ÊTRE ENDOMMAGÉ

SI LES INSTRUCTIONS DE SÉCURITÉ QUI SUIVENT CE MOT

INDICATEUR NE SONT PAS RESPECTÉES.

La page charge ...

EarthQuake 31043 Le manuel du propriétaire

Marque: EarthQuake

Modèle: 31043

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

31043 Badger™ Front Tine Tiller

Télécharger le PDF

rapport

dans d''autres langues

English: EarthQuake 31043 Owner's manual

EarthQuake 31043 Le manuel du propriétaire

Ce manuel convient également à

EarthQuake 31043 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents