EarthQuake MC440 Manuel utilisateur

GAS/OIL

RATIO

50:1

SN

Operator’s Manual

Original Operating Instructions

Manuel de l’utilisateur

Manual del operador

MC440

4-Cycle Cultivator

Motobineuse 4 temps

Cultivador de 4 ciclos

P/N: 23437

ECN: 11480

REV2: 01/10/17

Get parts online at

Pièces détachées en ligne à

Obtenga piezas en línea en

www.GetEarthquake.com

Includes Model:

Inclut le modèle, Incluye el modelo

12802

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

2

INTRODUCTION

Congratulations on your investment in quality. Thank you for purchasing a 4-cycle cultivator from Earthquake®. We have worked

to ensure that this cultivator meets the highest standards for usability and durability. With proper care, your cultivator will provide

many years of service.

Please read this entire manual before installation and use. Earthquake reserves the right to change, alter or improve the

product and this document at any time without prior notice.

CONTENTS

Registration ........................................................................................................................................................................................................................................2

Warnings and Safety Precautions ...........................................................................................................................................................................................3-7

Features/Specifications .................................................................................................................................................................................................................. 8

Unpacking and Assembly .............................................................................................................................................................................................................9

Operation ......................................................................................................................................................................................................................................9-13

Maintenance & Storage .........................................................................................................................................................................................................13-15

Troubleshooting and Repair ................................................................................................................................................................................................15-16

Parts Breakdown ......................................................................................................................................................................................................................17-21

15073 Border-Edger Kit Installation.........................................................................................................................................................................................22

DK43 Dethatcher Kit Installation ..............................................................................................................................................................................................23

Warranty ............................................................................................................................................................................................................................................24

FEDERAL EMISSIONS INFORMATION

Earthquake warrants to the retail purchaser, that this small, off-road engine was designed, built and equipped to conform at the

time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA).

This manual may contain information for several models. Read and keep this manual for future reference. This manual contains important

information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product information is

included with the unit. This information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES. This information must be

included to make sure state laws and other laws are followed. This manual should remain with the product even if it is resold.

OWNERSHIP RECORDS

Owner’s Name:

Owner’s Address:

City: State/Province: Zip Code/Postal Code:

Model Number: Serial Number:

Date of Purchase:

Notes:

REGISTRATION AND SERVICE

Record the engine model number and serial number in the space provided for easy reference

when ordering parts or requesting technical support. Excluding emissions-related warranty

items, the warranty is valid only if the completed registration is received by Ardisam within 30

days of purchase. (SEE WARRANTY SECTION FOR MORE INFORMATION.) You can register

your warranty online by visiting www.getearthquake.com, or by mailing it to: Ardisam, 1160

Eighth Avenue, Cumberland, WI 54829. If you do not have a computer, call our customer service

department at (800) 345-6007 Mondays through Fridays from 8 a.m. to 5 p.m. CST.

SERIAL

NUMBER

DECAL

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 3

WARNINGS AND SAFETY PRECAUTIONS

OWNER’S RESPONSIBILITY

Accurate assembly and safe and effective use of the machine is

the owner’s responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the machine according to directions and schedule

included in this Earthquake operator’s manual.

• Ensure that anyone who uses the machine is familiar with all

controls and safety precautions.

SPECIAL MESSAGES

Your manual contains special messages to bring attention to

potential safety concerns, machine damage as well as helpful

operating and servicing information. Please read all the

information carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual

that may help the operator in the operation or service of the

machine.

This symbol points out important safety

instructions which if not followed could endanger

your personal safety. Read and follow all

instructions in this manual before attempting to

operate this equipment.

BEFORE OPERATING ENGINE:

Please read this section carefully. Read entire operating and

maintenance instructions for this product. Failure to follow

instructions could result in serious injury or death. Operate the

machine according to the safety instructions outlined here and

inserted throughout the text. Anyone who uses this machine

must read the instructions and be familiar with the controls.

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER

REPRODUCTIVE HARM.

WARNING

YOU MUST READ, UNDERSTAND AND COMPLY WITH

ALL SAFETY AND OPERATING INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO SETUP AND

OPERATE YOUR MACHINE.

FAILURE TO COMPLY WITH ALL SAFETY AND

OPERATING INSTRUCTIONS CAN RESULT IN LOSS OF

MACHINE CONTROL, SERIOUS PERSONAL INJURY TO

YOU AND/OR BYSTANDERS, AND RISK OF EQUIPMENT

AND PROPERTY DAMAGE. THE TRIANGLE IN THE TEXT

SIGNIFIES IMPORTANT CAUTIONS OR WARNINGS

WHICH MUST BE FOLLOWED.

Intended Use / Foreseeable Misuse

IMPORTANT: This is a motorized rotary cultivator that works the

soil by means of rotating tines. It is pedestrian-controlled, but

not self-propelled, with a gasoline-fueled internal combustion

engine to power the tines. It shall not be used for any other

purpose.

DANGER

SRT CRT

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN DEATH OR SERIOUS INJURY AND/OR

PROPERTY DAMAGE.

IMPORTANT

IMPORTANT INDICATES HELPFUL INFORMATION FOR

PROPER ASSEMBLY, OPERATION, OR MAINTENANCE OF

YOUR EQUIPMENT.

NOTICE

NOTICE INDICATES YOUR EQUIPMENT CAN BE DAMAGED

IF THE SAFETY INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

CAUTION

CAUTION INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE.

DANGER

DANGER INDICATES A HAZARD WHICH, IF NOT AVOIDED,

WILL CERTAINLY RESULT IN DEATH OR SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

4

GENERAL SAFETY RULES

• Read, understand, and follow all instructions on the machine

and in the manual(s). Be thoroughly familiar with the controls

and the proper use of the machine before starting.

• Use this equipment for its intended purpose only.

• Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments or

accessories.

• Do not put hands or feet near or under rotating parts.

• Only allow responsible individuals who are familiar with the

instructions to operate the machine. Do not allow children

to operate this machine. Do not allow adults to operate the

machine without proper instruction.

• Thoroughly inspect the area where the machine is to be

used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury

or property damage. Stay away from breakable objects, such

as house windows, automobiles, greenhouses, etc.

• Wear appropriate clothing such as a long-sleeved shirt or

jacket. Also wear long trousers or slacks. Do not wear shorts.

Never wear sandals, sneakers or open shoes, and never

operate the machine with bare feet.

• Do not wear loose clothing or jewelry. They can get caught in

moving parts. Always keep hands, feet, hair and loose clothing

away from any moving parts on engine and machine.

• Always wear safety goggles or safety glasses with side shields

when operating the machine to protect your eyes from

foreign objects which can be thrown from the unit. Always

wear a protective hearing device.

• Always wear work gloves and sturdy footwear. Wear

footwear that will improve footing on slippery surfaces.

Leather work shoes or short boots work well for most people.

These will protect the operator’s ankles and shins from small

sticks, splinters, and other debris.

• It is advisable to wear protective headgear to prevent the

possibility of being struck by small flying particles, or being

struck by low hanging branches, twigs, or other objects

which may be unnoticed by the operator.

• Do not operate the machine without proper guards or other

safety protective devices in place.

• See manufacturer’s instructions for proper operation and

installation of accessories. Only use accessories approved

by the manufacturer.

• Operate only in daylight or good artificial light.

• Do not operate product when fatigued or under the

influence of alcohol, drugs or other medication which

can cause drowsiness or affect your ability to operate this

machine safely.

• Never operate machine in wet grass. Always be sure of your

footing; keep a firm hold on the handle and walk; never run.

• Watch for traffic when operating cultivator near, or when

crossing roads.

• If the equipment should start to vibrate abnormally, stop the

engine (motor), flip the ON/OFF switch to the OFF position.

Check immediately for cause. Vibration is generally a warning

of trouble. If the noise or vibrations of the machine increase,

stop immediately and perform an inspection.

• Never leave the machine unattended when the engine is

running. Flip the ON/OFF switch to the OFF position.

• Regularly inspect the machine. Make sure parts are not bent,

damaged or loose.

• Temperature of muffler and nearby areas may exceed 150°

F (65° C). Allow muffler and engine areas to cool before

touching. Never pick up or carry the machine while the

engine is running.

• Prolonged exposure to noise and vibration from gasoline engine-

powered equipment should be avoided. Take intermittent

breaks and/or wear ear protection from engine noise as well as

heavy work gloves to reduce vibration in the hands.

• Keep all screws, nuts and bolts tight.

• Do not transport the machine from one place to another

with the engine running.

• When moving the packaged machine, always do so with a

partner.

• Check local regulations for age restrictions on use of this

machine.

PRODUCTSPECIFIC SAFETY RULES

• Do not cultivate above underground utilities, including water

lines, gas lines, electric cables, or pipes. Do not operate the

machine on terrain/soil with large rocks and foreign objects

which can damage the equipment.

• After striking a foreign object, stop the engine. Flip the ON/

OFF switch to the OFF position. Inspect the machine for

damage. If damaged, repair before starting and operating

the machine.

• The tines of the cultivator should not rotate when the engine

is idling. If it does rotate when engine is idling, contact

Earthquake customer service for instruction.

• If an object becomes lodged in the tines, flip the ON/OFF

switch to the OFF position, allow to cool before attempting

to remove the foreign object.

• The clutch will transfer maximum power after about two

hours of normal operation. During this break-in period clutch

slippage may occur. The clutch should be kept free of oil or

other moisture for efficient operation.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 5

ENGINE SAFETY PRECAUTIONS

If your product comes with a separate engine manual, be

sure to read and follow all safety and warning precautions

outlined there, in addition to any in this manual.

Preventing Carbon Monoxide Poisoning

• Always start and run engine outdoors. Do not start or run

engine in an enclosed area, even if doors or windows are open.

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

• Never run engine outdoors in a poorly ventilated area where

the exhaust fumes may be trapped and not easily taken

away. (Examples include: in a large hole or areas where hills

surround your working area.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

• Always run the engine with the exhaust and muffler pointed

in the direction away from the operator.

• Never point the exhaust muffler towards anyone. People

should always be many feet away from the operation of the

engine and its attachments.

• Do not change the engine governor settings or over-speed

the engine.

Gasoline Fires and Handling Fuel Safely

Use extra care in handling gasoline and other fuels. They are

flammable and vapors are explosive.

• When storing extra fuel be sure that it is in an appropriate

container and away from any fire hazards.

• Prevent fire and explosion caused by static electric discharge.

Use only nonmetal, portable fuel containers approved by the

Underwriter’s Laboratory (U.L.) or the American Society for

Testing & Materials (ASTM).

• Always fill fuel tank outside in a well ventilated area. Never

fill your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.) Never

fill tank near appliances with pilot lights, heaters, or other

ignition sources. If the fuel has to be drained, this should

be done outdoors. The drained fuel should be stored in a

container specifically designed for fuel storage or it should

be disposed of carefully.

• Never remove the fuel cap or add fuel with the engine

running. Stop engine and allow to cool before filling.

• Never drain fuel from engine in an enclosed area.

• Always wipe up excess (spilled) fuel from engine before

starting. Clean up spilled fuel immediately. If fuel is spilled,

do not start the engine but move product and fuel container

from area. Clean up spilled fuel and allow to evaporate and

dry after wiping and before starting.

• Allow fuel fumes/vapors to escape from the area before

starting engine.

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

• Never smoke while refilling engine fuel tank.

• Do not store engine with fuel in fuel tank indoors. Fuel and

fuel vapors are highly explosive.

DANGER

ENGINES GIVE OFF CARBON MONOXIDE, AN ODORLESS,

COLORLESS, POISONOUS GAS. CARBON MONOXIDE MAY

BE PRESENT EVEN IF YOU DO NOT SMELL OR SEE ANY

ENGINE EXHAUST. BREATHING CARBON MONOXIDE CAN

CAUSE NAUSEA, FAINTING OR DEATH, IN ADDITION TO

DROWSINESS, DIZZINESS AND CONFUSION.

IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK

FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

CAUTION

HOT GASES ARE A NORMAL BYPRODUCT OF A

FUNCTIONING INTERNAL COMBUSTION ENGINE. FOLLOW

ALL SAFETY INSTRUCTIONS TO PREVENT BURNS AND

FIRES.

WARNING

NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR PRODUCT, YOU MUST ALWAYS FLIP THE ON/

OFF SWITCH TO THE OFF POSITION.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

6

• Never siphon fuel by mouth to drain fuel tank.

• Always have an adult fill the fuel tank and never allow

children to fill the engine.

• Never allow an adult or anyone under the influence of drugs

or alcohol to fill engine.

• When storing gasoline or equipment with fuel in the tank,

store away from furnaces, stoves, water heaters or other

appliances that have a pilot light or other ignition source

because they can ignite gasoline vapors.

BURNS AND FIRES

The muffler, muffler guard and other parts of the engine become

extremely hot during the operation of the engine. These parts

remain extremely hot after the engine has stopped.

Prevention of Burns and Fires

• Never remove the muer guard from the engine.

• Never touch the muffler guard because it is extremely hot

and will cause severe burns.

• Never touch parts of the engine that become hot after

operation.

• Always keep materials and debris away from muffler guard

and other hot parts of the engine to avoid fires.

CHILDREN AND BYSTANDERS

Tragic accidents can occur if the operator is not alert to the

presence of children and/or bystanders. Never assume that

others will remain where you last saw them.

• Keep the area of operation clear of all persons, especially

small children and pets. Keep children under the watchful

care of a responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while moving backwards, look behind and down

for small children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees,

or other objects that may obscure vision.

SERVICE

• Always stop the engine whenever you leave the equipment,

before cleaning, repairing or inspecting the unit. Engine

should be turned off and cool. Never make adjustments or

repairs with the engine (motor) running. Flip the ON/OFF

switch to the OFF position to prevent accidental starting.

• Always wear eye protection when you make adjustments or

repairs.

• Keep all nuts and bolts tight and keep equipment in good

condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• When servicing or repairing the machine, do not tip the

machine over or up unless specifically instructed to do so in

this manual. Service and repair procedures can be done with

the machine in an upright position. Some procedures will be

easier if the machine is lifted on a raised platform or working

surface.

• To reduce fire hazard, keep machine free of grass, leaves or

other debris build-up. Clean up oil or fuel spillage. Allow

machine to cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Clean and replace safety and instruction decals as necessary.

• Inspect machine before storage. When not in use, flip the

ON/OFF switch to the OFF position and store indoors in a

dry place locked or otherwise inaccessible to children.

• Use only original equipment parts from Earthquake,

including all nuts and bolts.

THE RIGHT AND LEFT SIDES

OF YOUR CULTIVATOR ARE

DETERMINED FROM THE

OPERATING POSITION AS

YOU FACE THE DIRECTION OF

FORWARD TRAVEL.

NOTICE

R

L

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 7

SAFETY DECALS

This cultivator has been designed and manufactured to provide you with the safety and reliability you would expect from an industry

leader in outdoor power equipment manufacturing.

Reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this

equipment safely and effectively. We have placed a safety decal on the cultivator to remind you of some of this important information

while you are operating the unit.

These important safety decals are illustrated below, and are shown here to help familiarize you with the location and content of the

safety messages you will see as you perform normal cultivating operations. Please review these decals now, and if you have any

questions regarding its meaning or how to comply with these instructions, reread the complete safety instruction text in this manual.

Should a decal become unreadable because of being worn, faded, or otherwise damaged during the use of your cultivator, please

use the part number information provided to order a replacement label. Customers can order by calling Earthquake customer service.

These decals are easily applied, and will act as a constant visual reminder to you, and others who may use the equipment, to follow

the safety instructions necessary for safe, effective operation of your cultivator.

Part No. 17301

Throttle Control Decal - Right Handlebar

Part No. 17918

Free Hand Safe Starting Location Decal - Left

Handlebar

Part No. 17048

Cultivator Warning Decal - Tine Shield

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

8

ENGINE DISPLACEMENT 40cc

FUEL TANK CAPACITY 0.75 L

FUEL TYPE Minimum 87 octane gasoline with

low ethanol content

NOTE: If using an ethanol blended

fuel, a fuel stabilizer, mixed to

manufacturer specications, is

recommended

OIL TANK CAPACITY 3.72 -oz

OIL TYPE OIL VIPER 4 CYCLE (p/n 13235)

10W-30

SPARK PLUG NGK CMR6A

SPARK PLUG GAP 0.024 inch

TRANSMISSION Bronze gear drive

GEAR RATIO 32:1

TILLING WIDTH 6 inch min. - 10 inch max.

TILLING DEPTH 8 inch max.

TINE SPEED 288 rpm max.

WHEEL SIZE 7.0 inch dia. x 1.375 inch wide

WEIGHT OF UNIT 33 lb

ASSEMBLED SIZE 33.6 x 17.8 x 40.6 inch

SPECIFICATIONS

FEATURES

TOOL-LESS REVERSIBLE

& REPLACEABLE TINES

3 POSITION

TOOL-LESS

WHEEL HEIGHT

ADJUSTMENT

EASY PULL-START

LOCATION

KNOBBY

COMFORT

GRIPS

THROTTLE

CONTROL

LEVER

HANDLEBAR

ON/OFF SWITCH

SEE THROUGH

FUEL TANK

2 POSITION TOOL-LESS

HANDLEBAR HEIGHT

ADJUSTMENT

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 9

UNPACKING AND ASSEMBLY

UNPACK CULTIVATOR

1. Carefully lift the cultivator out of the box, remove any packing

material and cut any ties holding the handlebar pieces to the

cultivator assembly.

2. Find parts packet. Parts packet contains:

4 - T-Handle Nuts (4640)

4 - Curved Washers (4641)

4 - Saddle Bolts (4642)

ASSEMBLY

1. Stand the cultivator assembly upright with tines and wheels

on a level surface. Wheels should be set in the lowest position

(See page 12 for wheel adjustment instructions). DO NOT

place the cultivator on a high surface where it can fall and

cause property damage or personal injury.

2. Using two T-handle nuts, two saddle bolts, and two curved

washers, attach the middle handlebar to the lower handlebar

that is already connected to the cultivator assembly (SEE

FIGURE 1. Make sure the pull cord is in the center of the

middle handle bar when attaching. The middle handlebar

can be installed in one of two positions, one high and one

low. DO NOT overtighten the T-handle nuts.

3. Attach the upper right and left handlebars to the middle

handlebar using the two remaining T-handle nuts, saddle

bolts, and curved washers (SEE FIGURE 1. DO NOT

overtighten the T-handle nuts.

4. The drag stake is shipped with point facing upwards. Before

using, remove lock pin and turn the drag stake around so the

point is directed in the downward position facing towards

the tines. Re-insert lock pin. SEE FIGURE 2

FIGURE 2

FIGURE 1

OPERATION

PREPARING ENGINE FOR STARTING

GAS AND OIL

NOTE:

Engine is shipped from factory without oil. You must add

engine oil before starting engine. If engine is started without oil,

engine may be damaged beyond repair and will not be covered

by warranty.

Quality

To operate the engine, we recommend using VIPER brand 4-cycle

oil (13235), included with each new cultivator, or an equivalent

10W-30 engine oil to ensure that the engine operates correctly

throughout the life of the engine. Use straight unleaded

premium gasoline, low/no ethanol blends recommended.

UPPER RIGHT

HANDLEBAR

CURVED

WASHER

UPPER LEFT

HANDLEBAR

T-HANDLE NUT

MIDDLE

HANDLEBAR

SADDLE BOLT

LOW POSITION

MOUNT HOLES

HIGH POSITION

MOUNT HOLES

LOWER

HANDLEBAR

LOCK PIN

DRAG STAKE

Checking and Adding Oil

Be sure the engine is located on a level surface before checking

or refilling oil. Proper position for checking oil level or refilling

oil is face down, with the gas tank of the cultivator down on a

horizontal surface. SEE FIGURE 3

NOTICE

ENGINE MUST BE TIPPED FORWARD WITH FUEL TANK

DOWN WHEN CHECKING OIL LEVEL OR FILLING WITH

OIL. FAILURE TO DO SO CAN RESULT IN OVERFILLING

THE ENGINE WITH OIL WHICH WILL IMPAIR THE ENGINE’S

PERFORMANCE. ONLY CHECK OIL AFTER LETTING

MACHINE SIT FOR FIVE MINUTES.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

10

STARTING AND STOPPING ENGINE

• Move the engine to a well ventilated area, outdoors, to

prevent carbon monoxide poisoning.

• Move to an area away from flames or sparks, to avoid

ignition of vapors if present.

• Remove all debris from air cleaner holes and gas cap to

ensure proper air flow.

• If it is the first time starting the cultivator, make sure the

included 4-cycle oil has been poured into the oil fill area.

COLD ENGINE START:

Starting engine for first time or after engine has cooled off or

after running out of fuel.

OIL DRAIN

SCREW

OIL DIPSTICK

HIGH OIL MARK

LOW OIL MARK

CULTIVATOR TIPPED FORWARD

ON LEVEL, HORIZONTAL SURFACE

FIGURE 3

DANGER

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU

MUST ADD ENGINE OIL BEFORE STARTING ENGINE.

IF ENGINE IS STARTED WITHOUT OIL, ENGINE MAY BE

DAMAGED BEYOND REPAIR AND WILL NOT BE COVERED BY

WARRANTY.

NEVER STORE ENGINE WITH FUEL IN THE TANK INDOORS.

FUEL AND FUEL VAPORS ARE HIGHLY FLAMMABLE.

ONLY AN ADULT MUST ALWAYS HANDLE AND FILL THE

ENGINE WITH FUEL.

ALWAYS HANDLE GAS IN A WELL VENTILATED AREA,

OUTDOORS, AWAY FROM FLAMES OR SPARKS.

DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OF

EXCESS FUEL AND ALLOW TO DRY. REMOVE ENGINE FROM

AREA TO AVOID SPARKS.

NOTICE

DO NOT SPRAY WATER ON OR NEAR THE ELECTRONICS OF

THE CULTIVATOR AS THIS MAY RESULT IN DAMAGE TO THE

ELECTRICAL COMPONENTS.

1. Clean around oil ll area.

2. Unscrew dipstick and wipe clean with cloth.

3. Reinsert dipstick (must be fully threaded for accurate reading).

4. Unscrew and check dipstick. If no oil shows on the dipstick,

refill so that the oil level appears between the low and high

marks on the dipstick. SEE FIGURE 3

5. Change oil if contaminated.

OPERATION TIPS

1. The clutch will transfer maximum power after about two

hours of normal operation. During this break-in period clutch

slippage may occur. The clutch should be kept free of oil and

other moisture for ecient operation.

2. Cultivate without placing excessive body weight on the unit.

The cultivator operates most eciently with the weight of the

unit itself.

3. Never run engine indoors. Exhaust fumes are deadly.

Filling Fuel Tank

1. Shut-o engine and allow engine to completely cool before

relling the fuel tank.

2. Move to a well ventilated area, outdoors, away from flames

and sparks.

3. Clean debris from area around the fuel cap.

4. Loosen fuel cap slowly. Prevent the cap from coming in

contact with dirt or debris.

5. Carefully add fuel without spilling.

6. Do not fill fuel tank completely full, allow space for fuel to

expand.

7. Immediately replace fuel cap and tighten. Wipe off spilled

fuel and allow to dry before starting engine.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 11

C

H

O

K

E

R

U

N

FIGURE 4

CAUTION

MAKE SURE THE UNIT IS IN A STABLE POSITION BEFORE

PULLING THE STARTER HANDLE.

WHEN THE UNIT START TO FIRE OR RUN, RETURN BOTH

HANDS TO THE HANDLEBAR POSITION TO MAINTAIN

CONTROL AND STABILITY OF THE UNIT.

IF ENGINE FAILS TO START AFTER FOLLOWING STARTING

PROCEDURES, PLEASE CONTACT OUR CUSTOMER SERVICE

DEPARTMENT AT 8003456007.

STARTER ROPE CAN CAUSE AN UNANTICIPATED JERK

TOWARD ENGINE. PLEASE FOLLOW INSTRUCTIONS TO

AVOID INJURY.

NEVER LEAVE ENGINE RUNNING WHILE UNATTENDED.

TURN OFF AFTER EVERY USE.

NEVER CARRY CULTIVATOR FROM ONE LOCATION TO

ANOTHER WHILE ENGINE IS RUNNING.

ALWAYS WEAR A PROTECTIVE HEARING DEVICE.

DO NOT START ENGINE IF FUEL IS SPILLED. WIPE OFF

EXCESS FUEL AND ALLOW TO DRY.

DANGER

DO NOT ATTEMPT TO START ENGINE IN THE FOLLOWING

WAYS:

• DO NOT USE STARTING FLUID.

• DO NOT SPRAY FLAMMABLE LIQUIDS OR VAPORS

INTO AIR CLEANER, CARBURETOR, OR SPARK PLUG

CHAMBER.

• DO NOT REMOVE SPARK PLUG AND ATTEMPT TO

START ENGINE. FLAMMABLE FUEL CAN SPRAY OUT &

IGNITE FROM A SPARK FROM SPARK PLUG.

1. Move choke lever to CHOKE position. SEE FIGURE 4

NOTE: CHOKE position is defined by moving the choke

lever as far to the right, towards gas tank, as possible.

2. Prime unit until primer hose is filled with gas.

NOTE: When using the primer bulb, allow the bulb to

return completely to its original position between pushes.

3. Push ON/OFF switch to the ON position.

4. Hold handle bar firmly. Grasp starter handle and pull out

slowly until it pulls slightly harder. Without letting the starter

handle retract, pull rope with a rapid full arm stroke. Let it

return to its original position slowly. Repeat this step every

time the starter rope is pulled until unit fires or runs.

NOTE: If engine fails to start after 5-6 pulls, push primer 1

time and pull starter rope again.

5. After engine starts running, move choke lever to HALF

CHOKE position until unit runs smoothly.

NOTE: Half choke is defined when the choke lever is

between CHOKE and RUN positions. SEE FIGURE 4

6. Move choke lever to RUN position and squeeze throttle to

desired speed. SEE FIGURE 4

NOTE: Run at full throttle when possible. Do not let unit

idle for extended periods of time.

7. To stop engine, push ON/OFF switch to OFF position.

HOT/WARM ENGINE START:

1. Begin with Step 3 of Cold Engine Starting.

2. If engine does not fire, refer to Step 1 of Cold Engine Starting.

TO STOP ENGINE:

Push the ON/OFF switch to the OFF position.

ADJUSTING WHEELS AND DRAG STAKE

The wheels on the cultivator can be adjusted to one of three

positions. The LOW wheel position is used for transporting the

cultivator across a smooth level surface while the engine is not

running. The HIGH and HIGHEST wheel positions are used when

cultivating in soil and help stabilize the unit when cultivating at

different depths. (SEE FIGURE 5

To adjust wheels up or down (SEE FIGURES 6 AND 7:

1. Pull the locking metal sleeve against the spring, away from the

vertical guide until it releases from one of the three notched

positions in the vertical guide.

2. Slide the wheel set up or down to the desired position, and

release the locking metal sleeve until it locks into desired

notch in the vertical guide.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

12

FIGURE 5

FIGURE 7

FIGURE 6

TINE REMOVAL AND INSTALLATION

To Remove Tines (SEE FIGURE 8)

1. Remove the hairpins from each end of the tine shaft.

2. Slide the four tines o the shaft.

To Install Tines

1. First slide the inside tines onto each end of the tine shaft.

One inside tine is stamped with a B and the other is

stamped with a C.

2. Slide the outside tine A and tine D onto each end of the

shaft next. The tines should be installed in the correct order

so that they are positioned left to right A, B, C, D, as viewed

from the user’s position on the MC440. Make sure that the

hub collars on both the right and left pairs of tines face

each other so that there is adequate spacing between the

tine blades. SEE FIGURE 8

3. Insert the hairpins into the holes at each end of the tine

shaft to lock the tines into place.

NOTE: Tines can be reversed so the pointed tip of the tines

are directed forward - for more aggressive digging. In this

arrangement, tines are positioned left to right D, C, B, A as

viewed from the user’s position

FIGURE 8

NOTE: To reduce cultivating width from 10” to 6”, remove

both outer tines and reinsert hairpins through the two inner

holes on the tine shaft to secure both inner tines in place.

LOW

POSITION

MIDDLE

POSITION

HIGH

POSITION

EXPANDED

SPRING

LOCKING METAL SLEEVE

(LOCKED POSITION)

COMPRESSED

SPRING

LOCKING METAL SLEEVE

(UNLOCKED POSITION)

LOCK PIN

DRAG STAKE

The drag stake is used to help regulate cultivating depth and

control the cultivator from leaping forward during operation.

Resistance to forward motion is greatest when the drag stake is

set in its lowest position allowing for deeper cultivation.

To adjust the drag stake (SEE FIGURE 7:

1. Pull the lock pin out of the drag stake mount hole.

2. Position the drag stake so the pointed tip is directed

downward.

3. Insert the lock pin into the hole that achieves desired

depth.

A

B

C

D

TINE SHAFT

INNER HOLE

HAIRPIN

HUB

COLLARS

INNER

TINE

OUTER

TINE

*Scan this QR code with your smartphone

for helpful hints and tips for using your

cultivator. www.getearthquake.com

You may need to get a QR Code® reader from your

smartphone app store. Data rates may apply.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 13

ENGINE MAINTENANCE

Refer to engine emission warranty included with your product

for maintenance schedule.

Good maintenance is essential for safe, economical, and trouble-

free operation. It will also help reduce air pollution. To help

you properly care for your engine, the following pages include

a maintenance schedule, routine inspection procedures, and

simple maintenance procedures using basic hand tools. Other

service tasks that are more difficult, or require special tools, are

best handled by professionals and are normally performed by a

technician or other qualified mechanic.

Maintenance, replacement or repair of the emissions control

devices and systems may be performed by any non-road

engine repair establishment or individuals. However, items

must be serviced by an authorized dealer to obtain “no charge”

emissions control warranty service.

MAINTENANCE AND STORAGE

STEPS FOR WORKING ON EQUIPMENT

1. Flip the ON/OFF switch to the OFF position. SEE FIGURE 9

2. Replace or repair the part on the cultivator.

3. Check all parts that were repaired, or removed during repair,

that they are secure and fit correctly.

NOTE: All repair parts must come from the factory. Never

replace parts that are not specifically designed for the

cultivator.

CULTIVATOR MAINTENANCE

1. Keep all screws, nuts, and bolts tight.

2. For cold weather operation, store the unit in a cool environment.

Transferring the unit from a cold to a warm place can cause the

build up of harmful condensation.

WARNING

PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE TURNED

OFF AND ALLOWED TO COOL BEFORE ATTEMPTING ANY

MAINTENANCE OR REPAIR.

TO PREVENT ACCIDENTAL STARTING:

• ENGINE MUST BE TURNED OFF AND COOL BEFORE

CHECK AND ADJUSTING ENGINE OR EQUIPMENT.

• TEMPERATURE OF MUFFLER AND NEARBY AREAS MAY

EXCEED 150° F 65° C. AVOID THESE AREAS.

• CHECK CULTIVATOR OFTEN FOR LOOSE NUTS AND

BOLTS. KEEP THESE ITEMS TIGHTENED.

• NEVER STORE ENGINE WITH FUEL IN THE TANK INSIDE

A BUILDING. POTENTIAL SPARKS MAY BE PRESENT

FOR IGNITION OF FUEL AND FUEL VAPORS.

• ONLY AN ADULT MUST DO MAINTENANCE AND REPAIR

ON ENGINE AND CULTIVATOR.

ON/OFF SWITCH

FIGURE 9

NOTICE

PROPER POSITION FOR CHECKING OIL LEVEL OR

REFILLING OIL IS FACE DOWN, WITH THE FUEL TANK

OF THE CULTIVATOR DOWN ON A HORIZONTAL

SURFACE. SEE FIGURE 3 ON PAGE 10. FAILURE TO

MAINTAIN THIS POSITION CAN RESULT IN OVER

FILLING THE ENGINE WITH OIL WHICH WILL IMPAIR

THE ENGINE’S PERFORMANCE. ONLY CHECK OIL

AFTER LETTING MACHINE SIT FOR FIVE MINUTES.

LUBRICATION

Choose engine oil that meets or surpasses the latest API service

classification. For temperatures higher than 32º F, use 10W-30

motor oil. Use SAE 5W-30 if temperatures are below 32º F.

OIL MAINTENANCE

After the first five hours of operating a new Viper engine the

oil should be replaced, and every 50 hours of operating time

thereafter. The oil should be changed every 25 hours if used

under severe conditions, such as in high temperatures or under

heavy loads. Check oil periodically; do not overfill!

CHANGING OIL

Be sure the engine is not operating and is located on a level

surface before checking or refilling oil. Engine should be warm

for easy removal of oil.

STEPS FOR CHANGING OIL

1. Flip the ON/OFF switch to the OFF position.

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

14

SPARK PLUG

The recommended spark plug is a NGK CMR6A. For

maintenance and care of the spark plug go online to www.

getearthquake.com for instructions or call Earthquake

customer service.

CARBURETOR

Never tamper with factory setting of the carburetor.

COOLING FINS

Cooling fins, air inlets and linkages must be free from any debris

before each use.

AIR FILTER

Never run engine without air cleaner properly installed. Added

wear and engine failure may occur if air cleaner is not installed

on engine.

Service air cleaner every 3 months or after 20 hours of operation.

Clean filter daily in extremely dusty conditions.

Steps for Replacing and Cleaning Air Filter

1. Before removing the air filter cover, move the choke lever to

the CHOKE position.

2. To remove air filter cover, unscrew the cover bolt with a screw

driver and gently pop out the front latch tab. The cover then

can be slid off the back latch tabs and away from the engine.

SEE FIGURE 10

3. Remove the foam filter and fiber filter elements. Replace with

a new fiber filter and a new oiled foam filter (SEE FIGURE 11),

or clean the original foam and fiber filters with warm water

and mild soap. Remember to thoroughly oil the foam filter

with 30 or 40 weight motor oil and squeeze out any excess oil

before reinstalling it. Make sure to press the foam filter evenly

into place over the fiber filter to ensure that the foam is fully

seated into its sealed position.

4. Replace the air filter cover by first connecting the back latch tabs

then swinging the cover, making sure the foam filter block stays

fully seated and in its proper position, and connect the front latch

tab so that it is secured into place.

5. Screw the cover bolt back into place. Check that the cover is

securely attached by pulling slightly on the cover. If the cover

doesn’t move when pulled, it is secure.

FIGURE 10

FIGURE 11

DANGER

TO AVOID INJURY OR DEATH, NEVER SIPHON FUEL BY

MOUTH.

NEVER STORE CULTIVATOR WITH FUEL IN THE FUEL TANK

INSIDE AN ENCLOSED AREA OR BUILDING.

NOTICE

NEVER TWIST AIR FILTERS WHEN CLEANING. ALWAYS

PRESS.

2. Unscrew oil drain screw and empty oil into suitable oil

container. (SEE FIGURE 3 on PAGE 10) Dispose of oil properly.

3. Reinsert drain screw and remove oil dipstick.

4. Fill with appropriate oil to “FULL“ or top line of dipstick (SEE

FIGURE 3 on page 10).

5. Reinsert dipstick or oil fill cap and tighten.

FRONT

LATCH TAB

AIR FILTER

COVER

BACK LATCH

TABS

COVER

BOLT

AIR FILTER

COVER

FOAM FILTER

ELEMENT

FIBER FILTER

ELEMENT

TRANSPORTING YOUR CULTIVATOR

1. After using the cultivator, and before transporting it in a truck

bed, check that the gas cap is screwed on (clockwise) tightly.

The gas cap will not leak during transporting if gas cap is tight.

Never transport engine inside an enclosed space within a

vehicle. Fuel or fuel vapors may ignite causing serious injury

or death.

2. If fuel is present in the fuel tank, transport in an open vehicle

in an upright position.

3. If an enclosed vehicle must be used, remove the fuel into an

approved red fuel container. DO NOT siphon by mouth.

4. Wipe away any spilled fuel from engine and cultivator. Allow

to dry.

5. Run the engine to use up the fuel in the carburetor and fuel

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 15

tank. Always run engine in a well ventilated area.

6. Fuel cap should be screwed down tightly before transporting

your cultivator in a vehicle.

LONGTERM STORAGE

If your cultivator will not be used for more than one month,

prepare it for long-term storage.

Steps for Long-Term Storage

1. Mix an appropriate amount of fuel stabilizer to fresh gasoline,

in the ratio recommended on the stabilizer packaging.

Run the engine for five minutes to distribute the stabilizer

mixture throughout the fuel system. This will prevent gum,

varnish and corrosion build up in your fuel system during

long-term storage for up to 12 months.

2. Remove all debris from cultivator tines and engine.

3. Store cultivator by placing it on a level surface, resting on

the fuel tank and tine shield. SEE FIGURE 12

TROUBLESHOOTING AND REPAIR

At Earthquake, we build quality and durability into the design

of our products; but no amount of careful design by us, and

careful maintenance by you, can guarantee a repair-free life for

your Earthquake cultivator. Most repairs will be minor, and easily

fixed by following the suggestions in the troubleshooting guide

in this section.

The guide will help you pinpoint the causes of common problems

and identify remedies.

For more complicated repairs, you may want to rely on your

retailer, an authorized service center or Earthquake. Earthquake

will make the necessary repairs if a service center is not available.

A parts breakdown is located toward the end of this manual.

We will always be glad to answer any questions you have, or

help you find suitable assistance. To order parts or inquire about

warranty, call or e-mail us using the contact information found

in this section.

ORDERING REPLACEMENT PARTS

Parts can be obtained from the store where the cultivator was

purchased or direct from the factory. To order parts visit www.

getearthquake.com or call 1-800-345-6007.

For other general questions, you can e-mail us at

[email protected].

Please include the following information with your order:

1) Part numbers

2) Part description

3) Quantity

4) Model number and serial number

SPARE PARTS

Only use approved Earthquake service parts.

STORAGE POSITION

FIGURE 12

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

16

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE REMEDY/ACTION

Engine will not start 1. Ignition switch in off position 1. Flip switch to ON position

2. Spark plug wire disconnected 2. Connect spark plug wire to spark plug

3. Out of fuel 3. Refuel

4. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug

5. Fuel line hose not positioned in bottom of

fuel tank

5. Push fuel line down into fuel in fuel tank

Engine runs rough,

floods during

operation

1. Dirty air filter 1. Clean or replace air filter

2. Choke partially engaged 2. Turn off choke

3. Carburetor out of adjustment 3. Call customer service

Engine is hard to start 1. Stale fuel 1. Drain old fuel and replace with fresh. Use fuel

stabilizer at end of season

2. Spark plug wire loose 2. Make sure spark wire is securely attached to spark

plug

3. Dirty carburetor 3. Clean carburetor, use fuel stabilizer, new gas can

Engine misses or lacks

power

1. Clogged fuel tank 1. Remove and clean fuel tank

2. Clogged air filter 2. Clean or replace air filter

3. Carburetor out of adjustment or bad 3. Call customer service

4. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug

Engine runs, then

quits

1. Gas cap not venting 1. Clean or replace gas cap, check vent

2. Plugged fuel filter 2. Clean or replace fuel filter

3. Carburetor out of adjustment or bad 3. Call customer service

Engine revs too high 1. Carburetor out of adjustment 1. Call customer service

Tines turn at idle 1. Idle speed too high 1. Adjust idle speed lower

2. Broken clutch spring 2. Replace clutch

Recoil hard to pull 1. Oil in combustion chamber 1. Remove spark plug and dry out chamber

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 17

KEY PART # DESCRIPTION QT Y.

1 23491 ENGINE 40CC 4-CYCLE 1

2 26013 TRANSMISSION ASSEMBLY 1

3 4641 CURVED WASHER M8 4

4 46141 BOLT M8 X 1.25 X 160 MM 2

5 4602 TINE C ASSEMBLY 1

6 4604 TINE D ASSEMBLY 1

7 4652 HAIRPIN 5/8 X 3/4 IN 2

8 13189 WHEEL 180 X 38 MM GREY 2

9 2431 WASHER M10 X 20 X 2 MM 2

10 13048 LOCK NUT M10 X 1.5 FLANGE 1

11 4625 BOLT M6 X 1.0 X 42 MM FLANGE 4

12 400020 LOCK NUT M5 X 0.8 MM FLANGE 2

13 23441 TINE SHIELD WITH WARNING 2

14 176 BOLT M5 X 0.8 X 10 MM FLANGE 2

15 13230 WASHER 16 X 21 X 1 MM 1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

2122

23

24

25

26

9

27

28

29

30

3

KEY PART # DESCRIPTION QT Y.

16 4685 WHEEL LOCK SPRING 1

17 4684 WHEEL LOCK TUBE 1

18 4600 DRAG STAKE 1

19 18039 LOCK PIN 8 X 40 MM 1

20 46142 BOLT M6 X 1.0 X 20 MM FLANGE 2

21 WASHER M6 X 12 X 1 MM 2

22 4650 NUT M6 X 1.0 NYLOCK 2

23 4674 WHEEL AXLE TUBE 1

24 4673 WHEEL HOLDER 1

25 12811 LOWER HANDLEBAR 1

26 4687 BOLT M10 X 1.5 X 225 MM FLANGE 1

27 4678 WHEEL GUIDE TUBE 1

28 4601 TINE A ASSEMBLY 1

29 4603 TINE B ASSEMBLY 1

30 400023 NUT M8 X 1.25 NYLOCK 2

W1200117

ILLUSTRATED PARTS BREAKDOWN  Hood & Tines Parts Explosion & Parts List

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

18

1,5

2,5

3,5

4,5

5

6,7

7

6,7

8

8,9

1,10

10

7

7,11

12

12,13

14

15,16

16

16,17

16,18

16,19

1,20

20

20,21

1

22

1,23

23

24

25,26

26

26,27

28

29

30,34

31,34

32,34

33,34

34

34,35,

36

34,36

37

39,40

38

40

40,42

43

1

40,41

7,11

ILLUSTRATED PARTS BREAKDOWN  Engine Parts Explosion

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 19

KEY PART # DESCRIPTION QT Y.

1 26205 BOLT M5 X 0.8 X 16 MM W/WASHER 17

2 13197 AIR FILTER COVER 1

3 26996 KIT AIR FILTER ELEMENTS 1

4 400020 LOCK NUT M5 X 0.8 MM FLANGE 2

5 13363 AIR FILTER KIT 1

6 23271 HOSE CLAMP CRANKCASE 2

7 13394 BREATHER HOSES KIT 1

8 13329 CARBURETOR KIT 1

9 13299 CARBURETOR GASKET 1

10 13390 CARBURETOR INSULATOR KIT 1

11 13395 HOSE CLAMP VALVE COVER 2

12 13400 IGNITION COIL KIT 1

13 26866 BOLT M4 X 0.7 X 20 MM W/WASHER 2

14 13243 SPARK PLUG NGK CMR6A 1

15 26867 BOLT M5 X 0.8 X 12 MM W/WASHER 3

16 18497 ENGINE SHROUD KIT 1

17 11043 SHROUD CAP SPARK PLUG ACCESS 1

18 11044 SCREW 3/16 X 1/2 IN PHILLIPS 1

19 22631 CLIP NUT 3/16 IN 1

20 13298 VALVE COVER KIT 1

21 13324 GASKET VALVE COVER 1

22 13244 RECOIL CLUTCH 1

KEY PART # DESCRIPTION QT Y.

23 13342 RECOIL ASSEMBLY 1

24 13393 OIL CAP WITH ORING 1

25 13202 HEAT SHIELD MUFFLER 1

26 13391 MUFFLER KIT 1

27 13181 BOLT M5 X 0.8 X 50 MM SOCKET 2

28 13320 WASHER M6 X 10 X 1 MM 1

29 19919 BOLT M6 X 1.0 X 10 SOCKET 1

30 19236 GAS CAP SELF VENTING 1

31 13295 RUBBER GAS TANK HOLDER TOP 1

32 13296 RUBBER GAS TANK HOLDER LEFT 1

33 13297 RUBBER GAS TANK HOLDER RIGHT 1

34 13388 GAS TANK KIT 1

35 17992 FUEL FILTER ALUMINUM CORE 1

36 13308 FUEL LINES KIT 1

37 13241 FLYWHEEL 1

38 300337 LOCK NUT M8 X 1.25 FLANGE 1

39 300462 WASHER 8.4 X 15.8 X 1.6 MM 2

40 11235 CLUTCH KIT 1

41 300449 WAVE WASHER 10 X 15 X 0.25 MM 2

42 300450 BOLT M8 X 1.25 X 25MM SHOULDER 2

43 26868 MOUNT RING AND SHROUD 1

ILLUSTRATED PARTS BREAKDOWN  Engine Parts List

Operator's Manual

MC440 4-Cycle Cultivator

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5

20

KEY PART # DESCRIPTION QT Y.

1 26013 TRANSMISSION ASSEMBLY 1

2 46144 DUST CAP 2

3 4606 FIBER WASHER 2

4 4646 TINE SHAFT SEAL 2

5*  TRANSMISSION CASTING LEFT 1

6 4650 NUT M6 NYLOCK 2

7 W1200117 WASHER M6 X 12 X 1 MM 2

8 4633 WHEEL & DRAG STAKE MOUNT 1

9 13600 BOLT M6 X 1.0 X 25 HEX FLANGE 2

10 25159 TINE SHAFT BUSHING STEEL 2

11 4610 TINE SHAFT SHIM 2

12 4651 GEAR AND TINE SHAFT ASSY 1

13 4616 BUSHING SPACER 1

KEY PART # DESCRIPTION QT Y.

14 4614 DRIVE SHAFT BUSHING BRONZE 2

15 21953 DRIVE SHAFT 1

16 4617 THRUST BEARING REDUCER 1

17 4618 THRUST WASHER 2

18 4619 THRUST BEARING CAGE 1

19 4623 BALL BEARING 9 X 26 X 8 MM 1

20 300414 CLUTCH DRUM 1

21 4620 JAM NUT M8 1

22*  TRANSMISSION CASTING RIGHT 1

23 26997 WASHER M6 X 12 X 1 MM CU 2

24 4647 BOLT M6 X 1.0 X 18 HEX FLANGE 6

25 13447 BOLT M6 X 1.0 X 8 PHILLIPS 2

26 4615 KIT THRUST BEARING SET 1

* PURCHASE TRANSMISSION ASSEMBLY 26013

1

2

3

4

5

6

7

8

9

10

11

12

2

3

4

11

10

13

14

15

16

17, 26

18, 26

14

20

21

22

23

25

19

24

ILLUSTRATED PARTS BREAKDOWN  Transmission Parts Explosion & Parts List

La page charge ...

EarthQuake MC440 Manuel utilisateur

Ce manuel convient également à

EarthQuake MC440 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents