Mitsubishi Electric GT25 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: GT25

Taper: Le manuel du propriétaire

GT25 General Description

Thank you for choosing Mitsubishi Electric Graphic Operation

Terminal (GOT).

GT2512-STBA

GT2510-VTBD

GT2508-VTBD

GT2512-STBD

GT2510-VTWD

GT2508-VTWD

GT2510-VTBA

GT2508-VTBA

GT2505-VTBD

GT2510-VTWA

GT2508-VTWA

Prior to use, please read both this manual and the

detailed manual thoroughly to fully understand the

product.

MODEL GT25-U-GD-E

Model

code

1D7MN4

IB(NA)-0800537ENG-L(2102)MEE

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant

manuals introduced in this manual carefully and pay full attention to

safety to handle the product correctly.

The precautions given in this manual are concerned with this

product.

In this manual, the safety precautions are ranked as "WARNING"

and "CAUTION".

Note that the CAUTION level may lead to a serious accident

according to the circumstances.

Always follow the instructions of both levels because they are

important to personal safety.

Please save this manual to make it accessible when required and

always forward it to the end user.

[DESIGN PRECAUTIONS]

Indicates that incorrect handling may cause

hazardous conditions, resulting in death or

severe injury.

Indicates that incorrect handling may cause

hazardous conditions, resulting in medium or

slight personal injury or physical damage.

 Some failures of the GOT, communication unit or cable may keep the outputs on

or off.

Some failures of a touch panel may cause malfunction of the input objects such

as a touch switch.

An external monitoring circuit should be provided to check for output signals

which may lead to a serious accident.

Not doing so can cause an accident due to false output or malfunction.

 Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to

configure the device that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect

output or malfunction.

 When the GOT backlight has a failure, the POWER LED blinks (orange/blue),

the display section dims, and inputs by a touch switch are disabled.

Failure to observe this instruction may result in an accident due to incorrect

output or malfunction.

Even if the display section dims, inputs by a touch switch may still be available.

This may cause an unintended operation of the touch switch.

For example, if an operator assumes that the display section has dimmed

because of the screen save function and touches the display section to cancel

the screen save, a touch switch may be activated.

The GOT backlight failure can be checked with a system signal of the GOT.

 The display section of the GOT is an analog-resistive type touch panel.

Do not touch two points or more simultaneously on the display section.

Doing so may cause a touch switch near the touched points to operate

unexpectedly, or may cause an accident due to an incorrect output or

malfunction.

 When programs or parameters of the controller (such as a PLC) that is monitored

by the GOT are changed, be sure to reset the GOT, or turn on the unit again after

shutting off the power as soon as possible.

Not doing so can cause an accident due to false output or malfunction.

 If a communication fault (including cable disconnection) occurs during monitoring

on the GOT, communication between the GOT and PLC CPU is suspended and

the GOT becomes inoperative.

For bus connection : The PLC CPU becomes faulty and the GOT becomes

inoperative.

For other than bus connection : The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant

operation to the system by using the switches of a device other than the GOT on

the assumption that a GOT communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

WARNING

CAUTION

WARNING

[MOUNTING PRECAUTIONS]

 To maintain the security (confidentiality, integrity, and availability) of the GOT

and the system against unauthorized access, DoS

attacks, computer viruses,

and other cyberattacks from unreliable networks and devices via network, take

appropriate measures such as firewalls, virtual private networks (VPNs), and

antivirus solutions.

Mitsubishi Electric shall have no responsibility or liability for any problems

involving GOT trouble and system trouble by unauthorized access, DoS

attacks, computer viruses, and other cyberattacks.

*1 DoS: A denial-of-service (DoS) attack disrupts services by overloading

systems or exploiting vulnerabilities, resulting in a denial-of-service (DoS) state.

 Products with the Cl.I, DIV.2 mark on the rating plate are suitable for use in Class

I, Division 2, Groups A, B, C and D hazardous locations, or nonhazardous

locations only.

This mark indicates that the product is certified for use in the Class I, Division2

environment where flammable gases, vapors, or liquids are not likely to exist

under normal conditions.

When using the products in the Class I, Division 2 environment, observe the

following to reduce the risk of explosion.

• This device is open-type and is to be installed in an enclosure suitable for

the environment and require a tool or key to open.

• Warning - Explosion Hazard - Substitution of any component may impair

suitability for Class I, Division 2.

• Warning - Explosion Hazard - Do not connect or disconnect equipment or

disconnect external connection terminals unless power has been removed or the

area is known to be non-hazardous.

• The side interface and extension interface of this equipment cannot be used

in Class I, Division 2 environments.



Les produits marqués Cl.I, DIV.2 sur la plaque signalétique peuvent être utilisés

en Class I, Division 2, local dangereux de groupe A, B, C et D, ou uniquement en

local non dangereux.

Ce logo indique que le produit est homologué pour utilisation en environnement

de Class I, Division 2 où, dans des circonstances anormales, il peut y avoir

présence de gaz, vapeurs ou liquides inflammables.

Si le produit est utilisé en environnement de Class I, Division 2, observer les

précautions suivantes pour réduire le risque d'explosion.

• Cet appareil est de type ouvert et il doit être installé dans une enceinte

appropriée à l'environnement et ne pouvant être ouverte qu'au moyen

d'une clé ou d'un outil.

• Avertissement - Danger d'explosion - Toute substitution de composant

peut compromettre l'aptitude à l'utilisation en Class I, Division 2.

• Avertissement - Danger d'explosion - Ne pas connecter ou déconnecter

l'équipement ni déconnecter les bornes de connexion externes quand le

circuit est sous tension, ni avant de d'être assuré de l'absence d'atmosphère

inflammable.

• L’interface latérale et l’interface d’extension de cet équipement ne

peuvent être utilisées dans les environnements de Classe I, Division 2.

 Do not bundle the control and communication cables with main-circuit, power or

other wiring.

Run the above cables separately from such wiring and keep them a minimum of

100mm apart.

Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

 When the GOT connects to an Ethernet network, the IP address setting is

restricted according to the system configuration.

When a GOT2000 series model and a GOT1000 series model are on an

Ethernet network, do not set the IP address 192.168.0.18 for the GOTs and the

controllers on this network.

Doing so can cause IP address duplication at the GOT startup, adversely

affecting the communication of the device with the IP address 192.168.0.18.

The operation at the IP address duplication depends on the devices and the

system.

 Turn on the controllers and the network devices to be ready for communication

before they communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

 When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

 Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

 Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the communication unit or the option unit onto/from

the GOT.

 Use the GOT in the environment that satisfies the general specifications

described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or

deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in the

specified torque range with a Phillips-head screwdriver No. 2.

• GT2512

, GT2510, GT2508: Specified torque range (0.36 N•m to 0.48 N•m)

• GT2505: Specified torque range (0.30 N•m to 0.50 N•m)

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage

of the screws or unit.

 When mounting a unit on the GOT, tighten the mounting screws in the following

specified torque range.

When loading the communication unit or option unit other than wireless LAN unit

to the GOT, fit it to the connection interface of the GOT and tighten the mounting

screws in the specified torque range (0.36 N•m to 0.48 N•m) with a Phillips-head

screwdriver No.2.

When loading the wireless LAN unit to the GOT, fit it to the side interface of GOT

and tighten the mounting screws in the specified torque range (0.10 N•m to 0.14

N•m) with a Phillips-head screwdriver No.1.

When the GOT is installed vertically, its side interface is positioned on the bottom.

To prevent the falling of the wireless LAN communication unit from the side

interface, install or remove the unit while holding it with hands.

Under tightening can cause the GOT to drop, failure or malfunction.

Overtightening can cause a drop, failure or malfunction due to the damage of the

screws or unit.

WARNING

CAUTION

WARNING

CAUTION

[WIRING PRECAUTIONS]

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

 When closing the USB environmental protection cover, note the following points

to ensure the IP rating.

[GT25 (except GT2505-V)]

Push the [PUSH] mark on the latch firmly to fix the cover to the GOT.

[GT2505-V]

Push the USB mark on the latch firmly to fix the cover to the GOT.

 Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may not

be removed.

 Do not operate or store the GOT in the environment exposed to direct sunlight,

high temperature, dust, humidity, or vibrations.

 When using the GOT in the environment of oil or chemicals, use the protective

cover for oil.

Failure to do so may cause failure or malfunction due to the oil or chemical

entering into the GOT.

 Be sure to shut off all phases of the external power supply used by the system

before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

 Make sure to ground the FG terminal and LG terminal of the GOT power supply

section solely for the GOT (ground resistance: 100 Ω or less, ground cable

diameter: 1.6 mm or more).

Not doing so may cause an electric shock or malfunction.

 When tightening the terminal screws, use a Phillips-head screwdriver No.2.

 Terminal screws which are not to be used must be tightened always at torque 0.5

N•m to 0.8 N•m.

Otherwise there will be a danger of short circuit against the solderless terminals.

 Use applicable solderless terminals and tighten them with the specified torque.

If any solderless spade terminal is used, it may be disconnected

when the terminal screw comes loose, resulting in failure.

 Correctly wire the GOT power supply section after confirming the rated voltage

and terminal arrangement of the product.

Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.5 N•m to 0.8 N•m).

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering the

GOT.

Not doing so can cause a fire, failure or malfunction.

 The module has an ingress prevention label on its top to prevent foreign matter,

such as wire offcuts, from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat

dissipation.

 Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in the

specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

 Plug the QnA/ACPU/Motion controller (A series) bus connection cable by

inserting it into the connector of the connected unit until it "clicks".

After plugging, check that it has been inserted snugly.

Not doing so can cause a malfunction due to a contact fault.

 Before testing the operation of a user-created monitor screen (such as turning on

or off a bit device, changing the current value of a word device, changing the set

value or current value of a timer or counter, and changing the current value of a

buffer memory), thoroughly read the manual to fully understand the operating

procedures.

During the test operation, never change the data of the devices which are used

to perform significant operation for the system.

False output or malfunction can cause an accident.

 When power is on, do not touch the terminals.

Doing so can cause an electric shock.

 Correctly connect the battery connector.

Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into

the fire.

Doing so will cause the battery to produce heat, explode, or ignite, resulting in

injury and fire.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage

of the screws or unit.

 Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling,

motion or accidental pulling of the cables or can cause a malfunction due to a

cable connection fault.

 When unplugging the cable connected to the unit, do not hold and pull from the

cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction

due to a cable connection fault.

 Do not drop the module or subject it to strong shock.

A module damage may result.

CAUTION

WARNING

CAUTION

WARNING

CAUTION

[TOUCH PANEL PRECAUTIONS]

[

PRECAUTIONS WHEN THE DATA STORAGE IS IN USE

]

[PRECAUTIONS FOR USE]

[PRECAUTIONS FOR REMOTE CONTROL]

[PRECAUTIONS FOR EXCLUSIVE AUTHORIZATION CONTROL]

 Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the

battery.

If the battery is dropped or given an impact, dispose of it without using.

 Before touching the unit, always touch grounded metals, etc. to discharge static

electricity from human body, etc.

Not doing so can cause the unit to fail or malfunction.

 Use the battery manufactured by Mitsubishi Electric Corporation.

Use of other batteries may cause a risk of fire or explosion.

 Dispose of used battery promptly.

Keep away from children.

Do not disassemble and do not dispose of in fire.

 Be sure to shut off all phases of the external power supply before replacing the

battery or using the dip switch of the terminating resistor.

Not doing so can cause the unit to fail or malfunction by static electricity.

 For the analog-resistive film type touch panels, normally the adjustment is not

required.

However, the difference between a touched position and the object position may

occur as the period of use elapses.

When any difference between a touched position and the object position occurs,

execute the touch panel calibration.

 When any difference between a touched position and the object position occurs,

other object may be activated.

This may cause an unexpected operation due to incorrect output or malfunction.

 If the SD card is removed from drive A of the GOT while being accessed by the

GOT, the GOT may stop processing data for about 20 seconds.

The GOT cannot be operated during this period.

The functions that run in the background including a screen updating, alarm,

logging, scripts, and others are also interrupted.

Since this interruption makes an impact to the system operation, it might cause

failure.

Check that the SD card access LED is off before removing the SD card.

 If the data storage is removed from the GOT while being accessed by the GOT,

the data storage and files may be damaged.

Before removing the data storage from the GOT, check the SD card access LED,

system signal, or others to make sure that the data storage is not accessed.

 Turning off the GOT while it accesses the SD card results in damage to the SD

card and files.

 Make sure to turn off the SD card access switch before removing the SD card

from the GOT.

Not doing so may damage the SD card or files. (GT2505 only)

 After inserting an SD card into the GOT, make sure to close the SD card cover.

Not doing so causes the data not to be read or written.

 When removing the SD card from the GOT, make sure to support the SD card by

hand as it may pop out.

Not doing so may cause the SD card to drop from the GOT, resulting in a failure

or break.

 When inserting a USB device into a USB interface of the GOT, make sure to

insert the device into the interface firmly.

Not doing so can cause a malfunction due to a contact failure.

 Before removing the data storage from the GOT, follow the procedure for

removal on the utility screen of the GOT.

After the successful completion dialog is displayed, remove the data storage by

hand carefully.

Not doing so may cause the data storage to drop from the GOT, resulting in a

failure or break.

 Do not touch the outer edge of the actual display area repeatedly.

Doing so may result in a failure.

 Do not turn off the GOT while data is being written to the storage memory (ROM)

or SD card.

Doing so may corrupt the data, rendering the GOT inoperative.

 Remote control is available through a network by using GOT functions, including

the SoftGOT-GOT link function, the remote personal computer operation

function, the VNC server function, and the GOT Mobile function.

If these functions are used to perform remote control of control equipment, the

field operator may not notice the remote control, possibly leading to an accident.

In addition, a communication delay or interruption may occur depending on the

network environment, and remote control of control equipment cannot be

performed normally in some cases.

Before using the above functions to perform remote control, fully grasp the

circumstances of the field site and ensure safety.

 Make sure to fully understand the GOT network interaction function before using

this function to control the authorization among pieces of equipment to prevent

simultaneous operations.

The exclusive authorization control of the GOT network interaction function can

be enabled or disabled for each screen.

(For all screens, the exclusive authorization control is disabled by default.)

Properly determine the screens for which the exclusive authorization control is

required, and set the control by screen.

A screen for which the exclusive authorization control is disabled can be

operated simultaneously from pieces of equipment.

Make sure to determine the operation period for each operator, fully grasp the

circumstances of the field site, and ensure safety to perform operations.

CAUTION

WARNING

CAUTION

WARNING

[DISPOSAL PRECAUTIONS]

[TRANSPORTATION PRECAUTIONS]

Manuals

The following shows manuals relevant to this product.

For detailed manuals and relevant manuals, refer to the e-Manual or PDF

manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (www.MitsubishiElectric.com/fa).

Compliance with the new China RoHS directive

GOT 相关的基于 “ 电器电子产品有害物质限制使用管理办法 ” 要求的表示方法

含有有害 6 物质的名称、含有量、含有部件

本产品中所含有的有害 6 物质的名称、含有量、含有部件如下表所示。

产品中有害物质的名称及含量

本表格依据 SJ/T11364 的规定编制。

○ : 表示该有害物质在该部件所有均质材料中的含量均在 GB/T26572 规定的限量要

求以下。

× : 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572 规定的

限量要求。

Referenced Standard: GB/T15969.2

(Requirement of Chinese standardized law)

Before using the GOT

Connect the connector of the GOT to the connector of the battery.

For GT2505, the battery is connected to the GOT before shipment.

Refer to the GOT2000 Series User’s Manual (Hardware) for the connection

instructions.

For details on the GOT specifications, installing instructions, wiring, maintenance

and inspection, or checking procedure for the version and the compatible standard,

refer to the GOT2000 Series User’s Manual (Hardware).

Packing List

The GOT product package includes the following:

 When disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to the

local regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

battery directive in the EU member states.)

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

regulated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner

they will not be exposed to the impact exceeding the impact resistance described

in the general specifications of this manual, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden packaging

from insects, they cause malfunction when entering our products.

Please take necessary precautions to ensure that remaining materials from

fumigant do not enter our products, or treat packaging with methods other than

fumigation (heat method).

Additionally, disinfect and protect wood from insects before packing products.

Manual name Manual number (Model code)

GOT2000 Series User’s Manual (Hardware)

SH-081194ENG (1D7MJ5)

GOT2000 Series User’s Manual (Utility)

SH-081195ENG (1D7MJ6)

Note: This symbol mark is for China only.

部件名称

有害物质

铅

（Pb）

汞

（Hg）

镉

（Cd）

六价铬

（Cr(VI)）

多溴联苯

（PBB）

多溴二苯醚

（PBDE）

电路板组件 × ○ ○ ○ ○ ○

树脂壳体、电缆、膜材 ○ ○ ○ ○ ○ ○

钣金部件、螺丝等金属部件 × ○ ○ ○ ○ ○

Description Quantity

GT25 1

Battery (GT11-50BAT) (Attached to the GOT) 1

Installation fitting 4

Gasket (for mounting the GOT on the control panel) 1 (only GT2505-VTBD)

GT25 General Description (This manual) 1

GOT2000 Series Supplementary Description

(Compliance with the ATEX Directive)

1 (only GT2510-VTWD,

GT2508-VTWD)

GOT2000 시리즈 보충 설명 (KCs 지침 준수 )

1 (only GT2510-VTWD,

GT2508-VTWD)

CAUTION

1. FEATURES

(1) Abundant standard equipment

• Variety of connection with FA devices

• SD card interface compatible with the SDHC card having a large capacity

and allowing high-speed communication

• Connection with various peripheral devices with the USB host

(2) Improved usability

• Abundant troubleshooting

• Easy and clear screen creation

• PC-like operation screen

• Support for the vertical installation

(3) Enhanced compatibility with Mitsubishi Electric FA devices

(4) Easy replacement]

(5) LED backlight

(6) Various extended functions supported

2. Part Names and Settings

The following shows the part names for GT2512, GT2510, GT2508 and GT2505.

No. Name Description

1) Display screen Displays the utility and the user-created screen

2) Touch panel

For operating the touch switches in the utility and the user-

created screen

USB interface

(Host/Front face)

For connecting a USB mouse, a USB keyboard, or a USB

barcode reader, and transferring or saving data

(Connector shape: TYPE-A) (only GT2512-STBA/D, GT2510-

VTBA/D

and GT2508-VTBA/D)

USB interface

(Device /Front face)

For connecting a personal computer

(Connector shape: Mini-B) (only GT2512-STBA/D, GT2510-

VTBA/D, GT2508-VTBA/D

and GT2505)

5) POWER LED

Lit in blue : Power is properly supplied

Lit in orange : Screen saving

Blinks in orange/blue : Backlight failure

Not lit : Power is not supplied

GT2512

1)2)

23)

17)

16)

10)

11)

12)

13)

14)

22)20) 19)

6) 6)

3)4)

15)

18)

21)

28)

GT2510

12)

13)

14)

23)22)20) 19)

17)

16)

6) 6)1)2)

18)

3)4)

24)

15)

21)

25)

10)

11)

28)

GT2508

10)11)12)

16)

13)

14)

23)22)20) 19)

6) 6)17)

6) 6)

1)2)

3)4)

15)

24)

18)

21)

28)

GT2505

10)

21)

19)20)

6) 6)

1)2)

14)6)

26)

22)

23)

12)16)

18)

27) 28)

*1: Special installation fittings are sold separately. If you need the special

installation fittings, consult your local sales office.

*2: GT2505 does not have the LG terminal.

3. Specifications

3.1 General Specifications

6) Unit installation fitting Mounting fixtures for fixing the GOT to the control panel

7) Reset switch Hardware reset switch

8) Installation switch Used for OS installations at the GOT startup

9) SD card access LED

Lit: SD card mounted

Blinking: SC card accessed

No lit: SD card not mounted or SD card mounted (removable)

10) SD card interface For installing a SD card

11) SD card cover

With a switching function for accepting and stopping the

access to the SD card (only GT2512, GT2510

and GT2508)

When the cover is opened : Access is prohibited

When the cover is closed : Access is allowed

12) Battery holder Houses the battery

13) Side interface For installing a communication unit

14)

USB interface

(Host/Back face)

For connecting a USB mouse, a USB keyboard, or a USB

barcode reader, and transferring or saving data

(Connector shape: TYPE-A)

15)

Hole for attaching a

cable clamp

Hole for attaching a cable clamp for preventing USB cable

from being pulled out

(Recommended product: SKB-132PWD of SK KOHKI CO.,

LTD. or corresponding product)

16)

Terminating resistor

setting switch

(Inside cover)

･ For GT2512, GT2510, GT2508

For switching on and off of the terminating resistor for the

RS-422/485 communication port (Default (Off))

･ For GT2505

For switching the terminating resistor for the RS-422/485

communication port to 330 Ω, 110 Ω, or OPEN

(Default: 330 Ω)

17) Extension interface For installing a communication unit or an option unit

18)

Vertical installation

arrow mark

For the vertical installation, install the GOT so that the arrow

points upward.

19) Power terminal Power input terminal, LG

terminal, FG terminal

20) Ethernet interface

For communicating with a controller or connecting a personal

computer (Connector shape: RJ-45 (modular jack))

21)

Ethernet

communication

status LED

SD/RD LED ON : Data sent or received

SD/RD LED OFF: Data not sent or received

SPEED LED ON : Communicating at 100 Mbps

SPEED LED OFF: Communicating at 10 Mbps or

disconnected

22) RS-232 interface

For communicating with a controller (Connector shape: D sub

9-pin (male))

23)

RS-422/485

interface

For communicating with a controller (Connector shape: D sub

9-pin (female))

24)

USB interface

(Device/Back face)

For connecting personal computers (Connector shape: Mini-

(only GT2510-VTWA/D, GT2508-VTWA/D)

25)

Special installation

fitting mounting

hole

For fixing the GOT to the control panel to make the GOT

conform to the ATEX/KCs standard.

(only GT2510-VTWA/D)

26)

SD card access

switch

For enabling or disabling the access to the SD card when

inserting/removing the SD card to/from the GOT (only

GT2505)

ON: SD card is being accessed. (The SD card cannot be

removed.)

OFF: SD card is not accessed. (The SD card can be

removed.)

27)

Preventive hole from

removing for the

USB cable

Hole fixed with banding band or others as a prevention from

removing for the USB cable

28) Rating plate -

Item Specifications

Operating ambient

temperature

Température

ambiante de

fonctionnement

0 to 55°C

*2*7

0 à 55°C

*2*7

Storage ambient

temperature

-20 to 60°C

Operating ambient

humidity

10 to 90% RH, non-condensing

Storage ambient

humidity

10 to 90% RH, non-condensing

Vibration resistance

Compliant

with JIS B

3502 and

IEC

61131-2

Frequency

Acceleration

Half-

amplitude

Sweep

count

Under

intermittent

vibration

5 to

8.4 Hz

3.5 mm

10 times

each in X,

Y and Z

directions

8.4

150 Hz

9.8m/s

Under

continuous

vibration

5 to

8.4 Hz

1.75 mm

8.4

150 Hz

4.9m/s

Shock resistance

Compliant with JIS B 3502 and IEC 61131-2 147 m/s

(15G),

3 times each in X, Y and Z directions

Operating

atmosphere

No greasy fumes, corrosive gas, flammable gas, excessive

conductive dust, and direct sunlight (Same as storage atmosphere)

Operating altitude

2000 m (6562 ft) max.

Installation location Inside control panel

No. Name Description

*1: The operating ambient temperature includes the temperature inside the

enclosure of the control panel to which the GOT is installed.

La température ambiante de fonctionnement inclut la température à l'intérieur

du boîtier du tableau de commande sur lequel le GOT est installé.

*2: When any of the following units and option is mounted on the GOT, the

maximum operating ambient temperature must be 5°C lower than the one

described above.

- MELSECNET/H communication unit (GT15-J71LP23-25 or GT15-J71BR13)

- CC-Link communication unit (GT15-J61BT13)

- Protective cover for oil

Lors du montage du module ou de l'option suivant, la température ambiante de

fonctionnement doit être réduite de 5°C par rapport aux valeurs maximales

dans les spécifications générales.

- Module de communication MELSECNET/H (GT15-J71LP23-25, GT15-

J71BR13)

- Module de communication CC-Link (GT15-J61BT13)

- Couvercle de protection contre l’huile

*3: Do not use or store the GOT under pressure higher than the atmospheric

pressure of altitude 0m (0ft.).Failure to observe this instruction may cause a

malfunction.When an air purge is made inside the control panel by adding

pressure, there may be a clearance between the surface sheet and the screen

making it difficult to use the touch panel, or the sheet may come off.

*4: This indicates the section of the power supply to which the equipment is

assumed to be connected between the public electrical power distribution

network and the machinery within the premises. Category II applies to

equipment for which electrical power is supplied from fixed facilities.

The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.

*5: This index indicates the degree to which conductive material is generated in the

environment where the equipment is used.

In pollution degree 2, only non-conductive pollution occurs but temporary

conductivity may be produced due to condensation.

*6: Some models have ANSI/ISA12.12.01 approval for use in Class I, Division 2

(ANSI/ISA 12.12.01, C22.2 No.213-M1987) hazardous locations.

For the details, please contact your local sales office.

*7: When GT2505 is installed vertically, the operating ambient temperature must

be between 0°C and 50°C.

Pour le GT2505 orienté à la verticale, la température ambiante de

fonctionnement doit être 0 à 50°C.

*8: Only for GT2505-V, the absolute humidity must not exceed 90% at 40°C if the

ambient temperature exceeds 40°C.

*9: GT2512, GT2510, GT2508 is for use on a flat surface of a Type 1 enclosure.

*10:GT2505 is for use on a flat surface of a Type 1 or Type 4X (indoor use only)

enclosure.

3.2 Power Supply Specifications

The following indicates the power supply specifications for GT25.

3.2.1 For GOTs powered from the 100 to 240VAC

power supply

Item Specifications

Overvoltage

category

II or less

Pollution degree

2 or less

Cooling method Self-cooling

Grounding

Grounding with a ground resistance of 100 Ω or less by using a ground

cable that has a cross-sectional area of 2 mm

or more.

If impossible, connect the ground cable to the control panel.

Type rating

UL Type 1

UL Type 1 or UL Type 4X (indoor use only)

*10

Point

Refer to the GOT2000 Series User’s Manual (Hardware) for details on the performance

specifications of each GOT.

Note

Operation at momentary failure

• If an instantaneous power failure occurs in the power supply and continues for more

than the permissible period, the GOT will be reset.

• Make sure to power on the unit more than 5 seconds after power-off.

Item

Specifications

GT2512-STBA

GT2510-VTBA,

GT2510-VTWA

GT2508-VTBA,

GT2508-VTWA

Power supply voltage Power supply voltage AC100 to 240VAC (+10%, -15%)

Power frequency 50/60Hz 5%

Max. apparent power 80VA 80VA 70VA

Power

consum

ption

maximum load 35W or less 34W or less 31W or less

Stand alone 14W 12W 11W

Stand alone with

backlight off

7W 7W 7W

Inrush current

60A or less (2ms, operating ambient temperature 25,

maximum load)

Allowable momentary power

failure time

20 ms or less (100VAC or more)

Noise immunity

1,500Vp-p noise voltage, 1 s noise width (when

measuring with a noise simulator under 25 to 60Hz

noise frequency)

Dielectric withstand voltage 1500VAC for 1 minute across power terminals and earth

Insulation resistance

10M or more across power terminals and earth by a

500V DC insulation resistance tester

Applicable wire size 0.75[mm

] to 2[mm

]

Applicable solderless terminal

Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,

V2-N3A, FV2-N3A

Applicable tightening torque

(Terminal block terminal screw)

0.5[N•m] to 0.8[N•m]

3.2.2 For GOTs powered from the 24VDC power

supply

3.3 External Dimensions

4. EMC AND LOW VOLTAGE DIRECTIVE

For the products sold in European countries, the conformance to the

EMC Directive, which is one of the European Directives, has been a

legal obligation since 1996. Also, conformance to the Low Voltage.

Directive, another European Directives, has been a legal obligation since

1997.

Manufacturers who recognize their products must conform to the EMC

and Low Voltage Directive are required to declare that their products

conform to these Directives and put a "CE mark" on their products.

• Authorized representative in Europe

Authorized representative in Europe is shown below.

Name :Mitsubishi Electric Europe BV

Address :Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany

4.1 Requirements to Meet EMC Directive

EMC Directives are those which require "any strong electromagnetic

force is not output to the external.:Emission (electromagnetic

interference)" and "It is not influenced by the electromagnetic wave from

the external.: Immunity (electromagnetic sensitivity)".

Items4.1.1 through4.1.3 summarize the precautions to use GOT and

configure the mechanical unit in order to match the EMC directives.

Though the data described herein are produced with our best on the

basis of the requirement items and standards of the restrictions gathered

by Mitsubishi Electric, they do not completely guaranteed that all

mechanical unit manufactured according to the data do not always

match the above.

Item

Specifications

GT2512-

STBD

GT2510-

VTBD,

GT2510-

VTWD

GT2508-

VTBD,

GT2508-

VTWD

GT2505-VTBD

Power supply voltage DC24 V (+25%, -20%)

DC24 V

(+10%, -15%)

Power

consum

ption

maximum load

37 W or

less

33 W or

less

31 W or

less

8.4 W or less

Stand alone 13 W 10 W 8 W 4.3 W

Stand alone with

backlight off

6 W 6 W 6 W 2.6 W

Inrush current

5 A or less (20 ms, operating

ambient temperature 25,

maximum load)

42 A or less (2 ms,

operating ambient

temperature 25,

maximum load)

Allowable momentary power

failure time

10 ms or less

Noise immunity

500 Vp-p noise voltage, 1 s

noise width (when measuring

with a noise simulator under 25

to 60 Hz noise frequency)

1000 Vp-p noise

voltage, 1 s noise

width (when

measuring with a

noise simulator

under 30 to 100 Hz

noise frequency)

Dielectric withstand voltage

350 V AC for 1 minute across

power terminals and earth

500 V AC for 1

minute across power

terminals and earth

Insulation resistance

10 M or more across power terminals and earth by a 500

V DC insulation resistance tester

Applicable wire size 0.75[mm

] to 2[mm

]

Applicable solderless terminal

Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,

V2-N3A, FV2-N3A

Applicable tightening torque

(Terminal block terminal screw)

0.5[N•m] to 0.8[N•m]

GT2510

GT2508

303 (11.93)

241 (9.49)

166 (6.54)

226 (8.90)

171.6

(6.76)

208 (8.19)

228 (8.98)

288 (11.34)

218 (8.58)

199 (7.83)

(0.39)

175 (6.89)

194 (7.64)

(0.39)

(2.05)

(0.24)

(2.05)

(0.24)

Unit : mm (inch)

37.5

(1.48)

37.5

(1.48)

GT2512

316 (12.44)

246 (9.69)

227 (8.94)

(0.39)

(2.05)

(0.24)

241 (9.49)

301 (11.85)

120(4.72)

152(5.98)

139(5.47)

53.5

122(4.80) 22

GT2505

164(6.46)

122(4.80)

(0.39)

(0.24)

(2.11)

(0.87)

4.1.1 EMC directive

The standards of the EMC Directive are shown below.

*1: The GOT is an open type device (device installed to another device) and must

be installed in a conductive control panel.

The above test items are conducted in the condition where the GOT is installed

on the conductive control panel and combined with the Mitsubishi Electric PLC.

*2: QP (Quasi-Peak): Quasi-peak value, Mean: Average value

*3: The above test items are conducted in the following conditions.

30 M-230 MHz QP: 40 dB V/m (10 m in measurement range)

230 M-1000 MHz QP: 47 dB V/m (10 m in measurement range)

4.1.2 Control panel

The GOT is an open type device (device installed to another device) and

must be installed in a conductive control panel.

It not only assure the safety but also has a large effect to shut down the

noise generated from GOT, on the control panel.

(1) Control Panel

(a) The control panel must be conductive.

(b) When fixing a top or bottom plate of the control panel with bolts,

do not coat the plate and bolt surfaces so that they will come into

contact.

And connect the door and box using a thick grounding cable in

order to ensure the low impedance under high frequency.

control panel, do not coat the fixing bolt area of the inner plate

and control panel to ensure conductivity in the largest area as

possible.

(d) Ground the control panel using a thick grounding cable in order to

ensure the low impedance under high frequency.

(e) The diameter of cable holes in the control panel must be 10cm

(3.94 in.). In order to reduce the chance of radio waves leaking

out, ensure that the space between the control panel and its door

is small as possible.

Paste the EMI gasket directly on the painted surface to seal the

space so that the leak of electric wave can be suppressed.

Applied

standard

Test standard Test details Standard value

EN61131-2

: 2007

CISPR16-2-3

Radiated noise

Electromagnetic

emissions from the

product are

measured.

30 M-230 MHz QP:

30 dB V/m (30 m in

measurement range)

*2, *3

230 M-1000 MHz QP:

37 dB V/m(30 m in

measurement range)

*2, *3

CISPR16-2-1

Conducted noise

Electromagnetic

emissions from the

product to the power

line is measured.

150 k-500 kHz QP: 79 dB,

Mean: 66 dB

500 k-30 MHz QP: 73 dB,

Mean: 60 dB

IEC61000-4-2

Electrostatic

immunity

Immunity test in

which static

electricity is applied

to the cabinet of the

equipment.

4 kV Contact discharge

8 kV Aerial discharge

IEC61000-4-3

Radiated

electromagnetic

field AM modulation

Immunity test in

which field is

irradiated to the

product.

80-1000 MHz: 10V/m

1.4-2 GHz: 3V/m

2.0-2.7 GHz: 1V/m

80%AM modulation@1kHz

EN61131-2

: 2007

IEC61000-4-4

Fast transient burst

noise

Immunity test in

which burst noise is

applied to the power

line and signal lines.

Power line: 2 kV

Digital I/O: 1 kV

Analog I/O: 1 kV

Signal lines: 1 kV

IEC61000-4-5

Surge immunity

Immunity test in

which lightening

surge is applied to

the product.

AC power type

Power line (between line and

ground): 2 kV

Power line (between lines)

: 1 kV

Data communication port

: 1 kV

DC power type

Power line (between line and

ground) : 0.5 kV

Power line (between lines)

: 0.5 kV

Data communication port

: 1 kV

IEC61000-4-6

Conducted RF

immunity

Immunity test in

which a noise

inducted on the

power and signal

lines is applied.

Power line: 10 V

Data communication port: 10 V

IEC61000-4-8

Power supply

frequency magnetic

field immunity

Test for checking

normal operations

under the

circumstance

exposed to the

ferromagnetic field

noise of the power

supply frequency

(50/60 Hz).

30 A/m

IEC61000-4-11

Instantaneous

power failure and

voltage dips

immunity

Test for checking

normal operations

at instantaneous

power failure.

AC power type

0.5 cycle 0% (interval 1 to 10s)

250/300 cycle 0%

10/12 cycle 40%

25/30 cycle 70%

Our test has been carried out on a panel having the damping

characteristics of 37 dB max. and 30 dB mean (measured by 3 m

method with 30 to 300 MHz).

(2) Connection of power and ground wires

Ground and power supply wires for the GOT must be connected as

described below.

(a) Provide a grounding point near the GOT. Short-circuit the LG and

FG terminals of the GOT (LG: line ground, FG: frame ground)

and ground them with the thickest and shortest wire possible

(The wire length must be 30 cm (11.81 in.) or shorter.)

The LG and FG terminals function is to pass the noise generated

in the PC system to the ground, so an impedance that is as low

as possible must be ensured. As the wires are used to relieve the

noise, the wire itself carries a large noise content and thus short

wiring means that the wire is prevented from acting as an

antenna.

Note) A long conductor will become a more efficient antenna at

high frequency.

(b) The earth wire led from the earthing point must be twisted with

the power supply wires.

By twisting with the earthing wire, noise flowing from the power

supply wires can be relieved to the earthing. However, if a filter is

installed on the power supply wires, the wires and the earthing

wire may not need to be twisted.

4.1.3 Noise filter (power supply line filter)

The noise filter (power supply line filter) is a device effective to reduce

conducted noise. Except some models, installation of a noise filter onto

the power supply lines is not necessary. However conducted noise can

be reduced if it is installed. (The noise filter is generally effective for

reducing conducted noise in the band of 10 MHz or less.) Usage of the

following filters is recommended.

The precautions required when installing a noise filter are described

below.

(1) Do not install the input and output cables of the noise filter together to

prevent the output side noise will be inducted into the input side cable

where noise has been eliminated by the noise filer.

(2) Connect the noise filter's ground terminal to the control panel with the

shortest cable as possible (approx. 10 cm (3.94 in.) or less).

4.2 Requirements for Compliance with the Low

Voltage Directive

The Low Voltage Directive requires each device which operates with

power supply ranging from 50 V AC to 1000 V and 75 V DC to 1500 V to

satisfy necessary safety items.

In the Sections from 4.2.1 to 4.2.5, cautions on installation and wiring of

the GOT to conform to the Low Voltage Directive requires are described.

We have put the maximum effort to develop this material based on the

requirements and standards of the Directive that we have collected.

However, compatibility of the devices which are fabricated according to

the contents of this manual to the above Directive is not guaranteed.

Each manufacturer who fabricates such device should make the final

judgement about the application method of the Low Voltage Directive

and the product compatibility.

4.2.1 Standard subject to GOT

4.2.2 Power supply

The insulation specification of the GOT was designed assuming

installation category II. Be sure to use the installation category II power

supply to the GOT.

The installation category indicates the durability level against surge

voltage generated by lightning strike.

Category I has the lowest durability; category IV has the highest

durability.

Model name FN343-3/05 FN660-6/06 RSHN-2003

Manufacturer SCHAFFNER SCHAFFNER TDK

Rated current 3 A 6 A 3 A

Rated voltage 250 V

• Installing the input and output cables

together will cause noise induction.

• Separate the input cable from the output

cable.

Standard applied to GOT : EN61131-2 Programmable controllers - Equipment

requirements and tests

Filter

Induction

Output side

(device side)

Input side

(power supply side)

Filter

Output side

(device side)

Input side

(power supply side)

Installation category

Category II indicates a power supply whose voltage has been reduced

by two or more levels of isolating transformers from the public power

distribution.

4.2.3 Control panel

Because the GOT is open type equipment (device designed to be stored

within another device), be sure to use it only when installed in a control

panel.

(1) Shock Protection

In order to prevent those who are unfamiliar with power facility, e.g.,

an operator, from getting a shock, make sure to take the following

measures on the control panel.

(a) Store the GOT within the control panel locked, and allow only

those who are familiar with power facility to unlock the panel.

(b) Build the structure in order that the power supply will be shut off

when the control panel is opened.

(2) Dustproof and waterproof features

The control panel also provides protection from dust, water and other

substances. Insufficient ingression protection may lower the

insulation withstand voltage, resulting in insulation destruction.

The insulation in the GOT is designed to cope with the pollution level

2, so use in an environment with pollustion level 2 or better.

4.2.4 Grounding

The following are applicable ground terminals. Use them in the grounded

state.

Be sure to ground the GOT for ensuring the safety and complying with

the EMC Directive.

4.2.5 External wiring

(1) External devices

When a device with a hazardous voltage circuit is externally

connected to the GOT, select a model which complies with the Low

Voltage Directive's requirements for isolation between the primary

and secondary circuits.

(2) Insulation requirements

Dielectric withstand voltages are shown in the following table.

Reinforced Insulation Withstand Voltage

(Installation Category II, source : IEC664)

5. INSTALLATION

5.1 Control Panel Inside Dimensions for

Mounting GOT

Install the GOT on the control panel out of the way for the equipment

inside the control panel. Do not install the GOT and the unit in

prohibited areas for the installation.

Pollution level 1: An environment where the air is dry and conductive

dust does not exist.

Pollution level 2: An environment where conductive dust does not

usually exist, but occasional temporary conductivity

occurs due to the accumulated dust.

Generally, this is the level for inside the control panel

equivalent a control room or on the floor of a typical

factory.

Pollution level 3: An environment where conductive dust exits and

conductivity may be generated due to the accumulated

dust.

An environment for a typical factory floor.

Pollution level 4: Continuous conductivity may occur due to rain, snow,

etc. An outdoor environment.

Functional grounding : Improves the noise resistance.

Rated voltage of hazardous

voltage area

Surge withstand voltage (1.2/50 s)

150 VAC or below 2500 V

300 VAC or below 4000 V

Point

Applicable cable

Some cables may need to be longer than the specified dimensions when connecting to the

GOT. Therefore, consider the connector dimensions and bending radius of the cable as

well for installation.

Category ICategory IICategory IIICategory IV

5.2 Panel Cutting Dimensions

5.3 Mounting Position

When mounting the GOT, the following clearances must be maintained

from other structures and devices.

Some cables may need to be longer than the specified dimensions when

connecting to the GOT.

Therefore, consider the connector dimensions and bending radius of the

cable as well for installation.

For the lead-in allowance for cables at the bottom of the GOT, refer to

the GOT2000 Series User’s Manual (Hardware) .

For the vertical installation, install the GOT so that the vertical installation

arrow printed on the GOT rear face points upward.

For GT2512, GT2510, GT2508

For GT2505

According to the dimensions in the following table, leave clearances

between the GOT and the other devices. The values enclosed in square

brackets apply to the case where no other equipment generating

radiated noise (such as a contactor) or heat is installed near the GOT.

However, keep the ambient temperature of the GOT to 55°C or lower.

Unit: mm(inch)

Item GT2512 GT2510 GT2508 GT2505

GOT only

48(1.89) or more

[18(0.71) or more]

48(1.89)

or more

[29(1.14)

or more]

50(1.97) or more

[20(0.79) or more]

Ethernet communication

unit is fitted

48(1.89) or more

[18(0.71) or more]

Bus connection unit is fitted

48(1.89) or more

[18(0.71) or more]

23(0.91)

or more

[29(1.14)

or more]

Serial connection unit is fit-

ted

48(1.89) or more

[18(0.71) or more]

CC-Link communication unit

(GT15-J61BT13) fitted

48(1.89) or more

[18(0.71) or more]

MELSECNET/H communi-

cation unit (coaxial) fitted

48(1.89)

or more

[38(1.50)

or more]

48(1.89)

or more

[45(1.77)

or more]

67(2.64)

or more

MELSECNET/H

communication

unit(optical) fitted

48(1.89) or more

[18(0.71) or more]

CC-Link IE TSN

communication unit is fitted

48(1.89) or more

[18(0.71) or more]

CC-Link IE Controller

Network

communication unit fitted

48(1.89) or more

[18(0.71) or more]

CC-Link IE Field Network

communication unit fitted

48(1.89) or more

[18(0.71) or more]

GOT A B

2510

2508

289 (11.38)

227 (8.94)

+2 (0.08)

0 (0)

+2 (0.08)

0 (0)

200 (7.87)

176 (6.93)

+2 (0.08)

0 (0)

+2 (0.08)

0 (0)

2512

302 (11.89)

+2 (0.08)

0 (0)

228 (8.98)

+2 (0.08)

0 (0)

(0.39)

or more

2505

153 (6.02)

+2 (0.08)

0 (0)

121 (4.76)

+2 (0.08)

0 (0)

Horizontal

Vertical

Unit: mm (inch)

*Panel thickness : 1.6 to 4 mm

(0.06 to 0.16 inch)

Panel thickness:

1.6 to 4mm

(0.06 to 0.16 inch)

Panel thickness:

1.6 to 4mm

(0.06 to 0.16 inch)

Horizontal

Vertical

Panel thickness:

1.6 to 4mm

(0.06 to 0.16 inch)

Panel thickness:

1.6 to 4mm

(0.06 to 0.16 inch)

Horizontal

Vertical

*1: This value is for use of the coaxial cable 3C-2V (JIS C 3501).

For specifications of the cable, refer to the GOT2000 Series Connection Manual

for a controller used.

*2: This value differs depending on the cable used.

*3: When opening or closing the battery cover: 72(2.83) or more

5.4 Control Panel Inside Temperature and

Installation Angle

When installing the GOT to a panel, set the display section as shown

below.Using the GOT with the installation angle other than the following

deteriorates the GOT earlier.

Installing the GOT horizontally

When installing the GOT with the installation angle between 60 to

105°, the temperature inside the control panel must be within 55°C.

When installing the GOT with the installation angle other than

between 60 to 105°, the temperature inside the control panel must be

within 40°C.

Installing the GOT vertically

When the GOT is installed a 90° angle, the control panel inside

temperature must be within 55°C

. When the GOT is installed at any

angle other than 90°, the control panel inside temperature must be

within 40°C.

Horizontal Vertical

*1: For GT2505, the control panel inside temperature must be within 50°C.

5. INSTALLATION

5.1 Dimensions intérieures du tableau de

commande pour le montage du GOT

Installez le GOT sur le tableau de commande en laissant de l'espace

pour le dispositif à l'intérieur du tableau de commande. N'installez

pas le GOT et le module dans des zones où l'installation est interdite.

5.2 Cotes de découpe du panneau

Printer unit fitted

48(1.89) or more

[18(0.71) or more]

External I/O unit fitted

48(1.89) or more

[18(0.71) or more]

Sound output unit fitted

48(1.89) or more

[18(0.71) or more]

Horizontal: 78(3.07) or more

[18(0.71) or more]

Vertical: 48(1.89) or more

[18(0.71) or more]

Horizontal:

80(3.15)

or more

[20(0.79)

or more]

Vertical: 50(1.97)

or more

[20(0.79) or more]

When the SD card is used

50(1.97) or more

[20(0.79) or more]

50(1.97)

or more

Horizontal:

50(1.97) or more

[20(0.79) or more]

Vertical: 80(3.15)

or more

[20(0.79) or more]

When the SD card is not

used

50(1.97) or more

[20(0.79) or more]

Horizontal: 50(1.97) or more

[20(0.79) or more]

Vertical: 80(3.15) or more

[20(0.79) or more]

50(1.97) or more

[20(0.79) or more]

100(3.94) or more

[20(0.79) or more]

Point

Câble applicable

Certains câbles peuvent être plus longs que les dimensions spécifiées lors de la

connexion au GOT. Par conséquent, prenez également en compte les dimensions du

connecteur et le rayon de courbure du câble pour l'installation.

Item GT2512 GT2510 GT2508 GT2505

GOT

Display section

Panel or others

105°

60°

GOT

Display section

Panel or others

90°

GOT

2510

2508

289 (11,38)

227 (8,94)

+2 (0,08)

0 (0)

+2 (0

,08)

0 (0)

200 (7,87)

176 (6,93)

+2 (0,08)

0 (0)

+2 (0

,08)

0 (0)

2512

302 (11,89)

+2 (0,08)

0 (0)

228 (8,98)

+2 (0,08)

0 (0)

Horizontal

Vertical

(0,39)

ou plus

2505

153 (6,02)

+2 (0,08)

0 (0)

121 (4,76)

+2 (0,08)

0 (0)

Unité : mm (pouce)

paisseur du panneau : 1,6 à 4mm

(0,06 à 0,16 pouce)

5.3 Position de montage

Lors du montage du GOT, laissez les espaces suivants pour les autres

structures et dispositifs.Certains câbles peuvent être plus longs que les

dimensions spécifiées lors de la connexion au GOT.

Par conséquent, prenez également en compte les dimensions du

connecteur et le rayon de courbure du câble pour l'installation.

Pour connaître l'espace à laisser pour les câbles sous le GOT, référez-

vous au manuel GOT2000 Series User’s Manual (Hardware).

Pour l’installation à la verticale, installez le GOT de sorte que la flèche

d’installation à la verticale imprimée sur la face arrière du GOT pointe

vers le haut.

Pour le GT2512, GT2510, GT2508

Pour le GT2505

Laissez les espaces entre le GOT et les autres dispositifs en fonction

des dimensions contenues dans le tableau suivant. Les valeurs entre

parenthèses s'appliquent au cas où aucun dispositif générant des

émissions sonores (comme un contacteur) ou de la chaleur n'est installé

près du GOT.

Toutefois, maintenez la température ambiante du GOT à 55°C ou moins.

Unité: mm (pouce)

Article

GT2512 GT2510 GT2508 GT2505

GOT uniquement

48 (1,89) ou plus

[18 (0,71) ou plus]

48 (1,89)

ou plus

[29 (1,14)

ou plus]

50 (1,97) ou

plus

[20 (0,79) ou

plus]

Unité de communication

Ethernet encastrée

48 (1,89) ou plus

[18 (0,71) ou plus]

Unité de connexion de bus

encastrée

48 (1,89) ou plus

[18 (0,71) ou plus]

23 (0,91)

ou plus

[29 (1,14)

ou plus]

Unité de connexion série

encastrée

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de communication

CC-Link (GT15-J61BT13)

encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de communication

MELSECNET/H (coaxial)

encastré

48 (1,89)

ou plus

[38(1,50)

ou plus]

48 (1,89)

ou plus

[45 (1,77)

ou plus]

67 (2,64)

ou plus

Module de communication

MELSECNET/H (optique)

encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de communication

CCLink IE TSN encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de communication

réseau de contrôleur CC-

Link IE encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de communication

réseau de champ CC-Link

IE encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Imprimante encastrée

48 (1,89) ou plus

[18 (0,71) ou plus]

Module d'E/S externe

encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Module de sortie acous-

tique encastré

48 (1,89) ou plus

[18 (0,71) ou plus]

Horizontal: 78 (3,07) ou plus

[18 (0,71) ou plus]

Vertical: 48 (1,89) ou plus

[18 (0,71) ou plus]

Horizontal: 80

(3,15) ou plus

[20 (0,79) ou

plus]

Vertical: 50

(1,97) ou plus

[20 (0,79) ou

plus]

Épaisseur du panneau :

1,6 à 4mm

(0,06 à 0,16 pouce)

Épaisseur du panneau :

1,6 à 4mm

(0,06 à 0,16 pouce)

Vertical

Horizontal

Épaisseur du panneau :

1,6 à 4mm

(0,06 à 0,16 pouce)

Épaisseur du panneau :

1,6 à 4mm

(0,06 à 0,16 pouce)

Vertical

Horizontal

*1: Cette valeur est utilisée pour le câble coaxial 3C-2V (JIS C 3501).

Pour connaître les spécifications du câble, référez-vous au manuel GOT2000

Series Connection Manual for a controller used.

*2: Cette valeur diffère selon le câble utilisé.

*3: Pour ouvrir ou fermer le couvercle de la batterie : 72 (2,83) ou plus

5.4 Température intérieure et angle

d'installation du tableau de commande

Lors de l'installation du GOT sur un panneau, réglez la zone d'affichage

comme indiqué ci-dessous.

Si l'angle d'installation est différent de celui indiqué, le GOT se détériore

plus tôt.

Installation du GOT à l’horizontale

Lors de l'installation du GOT avec un angle d'installation compris entre

60 et 105°, la température à l'intérieur du tableau de commande doit

être d'environ 55°C. Lors de l'installation du GOT avec un angle

d'installation non compris entre 60 et 105°, la température à l'intérieur

du tableau de commande doit être d'environ 40°C.

Installation du GOT à la verticale

Lors de l’installation du GOT avec un angle de 90°, la température à

l’intérieur du panneau de commande ne doit pas dépasser 55°C

Lors de l’installation du GOT avec tout autre angle que 90°, la

température à l’intérieur du panneau de commande ne doit pas

dépasser 40°C.

Horizontal Vertical

*1 : Pour le GT2505, la température à l’intérieur du panneau ne doit pas dépasser

50°C.

6. MAINTENANCE AND INSPECTION

Refer to the GOT2000 Series User’s Manual (Hardware) for

maintenance and inspection for the GOT.

Warranty

Mitsubishi Electric will not be held liable for damage caused by

factors found not to be the cause of Mitsubishi Electric; machine

damage or lost profits caused by faults in the Mitsubishi Electric

products; damage, secondary damage, accident compensation

caused by special factors unpredictable by Mitsubishi Electric;

damages to products other than Mitsubishi Electric products; and to

other duties.

For safe use

• This product has been manufactured as a general-purpose part for

general industries, and has not been designed or manufactured to

be incorporated in a device or system used in purposes related to

human life.

• Before using the product for special purposes such as nuclear

power, electric power, aerospace, medicine or passenger

movement vehicles, consult with Mitsubishi Electric.

• This product has been manufactured under strict quality control.

However, when installing the product where major accidents or

losses could occur if the product fails, install appropriate backup or

failsafe functions in the system.

Quand la carte SD est util-

isée

50 (1,97) ou plus

[20 (0,79) ou plus]

50 (1,97)

ou plus

Horizontal: 50

(1,97) ou plus

[20 (0,79) ou

plus]

Vertical: 80

(3,15) ou plus

[20 (0,79) ou

plus]

Quand la carte SD n'est

pas

utilisée

50 (1,97) ou plus

[20 (0,79) ou plus]

Horizontal: 50 (1,97) ou plus

[20 (0,79) ou plus]

Vertical: 80 (3,15) ou plus

[20 (0,79) ou plus]

50 (1,97) ou

plus

[20 (0,79) ou

plus]

100 (3,94) ou plus

[20 (0,79) ou plus]

Article

GT2512 GT2510 GT2508 GT2505

GOT

Zone d'affichage

Tableau ou autres

105°

60°

90°

Zone d'affichage

GOT

Tableau ou autres

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry

of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.

Printed in Japan, February 2021.

Mitsubishi Electric GT25 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: GT25

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Mitsubishi Electric GT25 Owner's manual

Mitsubishi Electric GT25 Le manuel du propriétaire

Mitsubishi Electric GT25 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents