Comelit IPPTZ120IRD Manuel utilisateur

IP PTZ CAMERA

ART. IPPTZ120IRD – IPPTZ130IRB

Please read this manual thoroughly before use and keep it for future reference

Contents

1. Introduction .............................................................................................................................................................................. 1

Features .............................................................................................................................................................................. 1

2. Hardware Installation ............................................................................................................................................................... 2

System requirement ............................................................................................................................................................ 2

Installation environment ...................................................................................................................................................... 2

Installation environment requirements ........................................................................................................................ 2

Recommend operating environment .......................................................................................................................... 2

Hardware installation steps ........................................................................................................................................ 2

Network connection .................................................................................................................................................... 3

Connection instruction ........................................................................................................................................................ 4

3. Operating Guide for Network High Speed Dome ..................................................................................................................... 5

Set the IE Browser .............................................................................................................................................................. 5

Download and Install ActiveX .............................................................................................................................................. 6

Login ................................................................................................................................................................................... 7

Live view ............................................................................................................................................................................. 8

System specification setting .............................................................................................................................................. 11

System ..................................................................................................................................................................... 11

Basic info ......................................................................................................................................................... 11

User manage ................................................................................................................................................... 15

PTZ Config ...................................................................................................................................................... 15

Record ............................................................................................................................................................. 17

Time zone ........................................................................................................................................................ 19

Micro-SD status ............................................................................................................................................... 20

AV ............................................................................................................................................................................. 21

Video channels ................................................................................................................................................ 21

Video parameters ............................................................................................................................................ 22

Privacy Mask ................................................................................................................................................... 23

Shot parameters .............................................................................................................................................. 24

Image parameters ........................................................................................................................................... 25

Network .................................................................................................................................................................... 26

Ethernet ........................................................................................................................................................... 26

DDNS .............................................................................................................................................................. 27

Netport ............................................................................................................................................................. 28

Other protocol .................................................................................................................................................. 29

P2P .................................................................................................................................................................. 29

Alarm configuration .................................................................................................................................................. 30

Alarm Conf ...................................................................................................................................................... 30

IO Alarm .......................................................................................................................................................... 30

Motion .............................................................................................................................................................. 31

Local......................................................................................................................................................................... 33

Local ................................................................................................................................................................ 33

Playback ........................................................................................................................................................................... 34

4 Appendix ................................................................................................................................................................................. 35

Specifications art. IPPTZ120IRD ....................................................................................................................................... 37

Specifications art. IPPTZ130IRB ....................................................................................................................................... 37

Network Interface of Network High Speed Dome .............................................................................................................. 39

Default Network Parameters ............................................................................................................................................. 39

Frequently asked questions .............................................................................................................................................. 39

CAUTION

 Non-technician should not try to operate this high speed dome before reading this manual carefully. (This manual are subject to

change without prior notice.)

 Cut the power supply off before operating the device to avoid damage caused by mal-operation.

 Interior of the camera are precision optical and electrical instruments. Heavy pressure, shock and other incorrect operations should

be prevented. Otherwise, may cause damage to product.

 Please do not use the product under circumstances where the limits exceed the maximum specified temperature, humidity or power

supply specifications.

 Contents in this manual may be different from the edition that you are using. Should any unsolved problem occur given that the

product is used according to this manual, please contact our technical support department or your product suppliers.

 This manual content will be updated unscheduled, our company reserves the right to do manual contents update without further

notice.

 The default username for this device is “admin”, and the password is “blank”. Default IP address is 192.168.1.188, HTTP port is 80.

PACKING LIST

Open the package, and check whether the accessories all contained.

Part

Quantity

IP speed dome (Include bracket)

1

Power supply

1

Screws bag

1

CD

1

Glove

2

Note:

 When open the box, please check all of parts carefully, confirm the parts as same as packing list.

 Please read the user manual carefully before the installation.

 Make sure to turn off all the power when install the camera

 Please confirm the power transformer, avoid the device damage with unmatched power source

Contact your local retailer without hesitate if anything is missing in your package.

1

1. Introduction

Features

 Build in 20x / 30X optics zoom lens, 2MP / 3MP, 1~60 fps

 True Day/Night switch

 H.264 High Profile/MJPEG encoding, VBR/CBR, dual stream

 Privacy mask, motion detection

 Alarm linkage output, micro-SD card video recording, snapshot, FTP upload, Email inform, link preset, CMS inform

 ONVIF 2.2 Profile-S protocol, GB/T28181 protocol

 360° horizonal continuous rotation; vertical 0°-90°,255 presets

 Low power consumption – MTTF up to 30,000 hours

 2CH alarm input, 1CH alarm output, build in micro-SD card slot, audio input/ output, 100 Mbit/s Ethernet

 IP66 protection level

2

2. Hardware Installation

System requirement

 LAN or WAN Internet to connect server, via PC Ethernet (network card or network cable) TCP/IP protocol connect , suggest

Internet Explorer 8.0 version or later.

 Monitor and PC configuration:

CPU: Dicaryon 2.8G or later, RAM: 512M or later (Above DirectX 8.1)

 Monitor: 17", 1920×1080 resolution

 Operation system: Windows NT, Windows2000, Windows XP, Windows 7 or later

Installation environment

Installation environment requirements

Far away from humid or high-temperature environment; choose proper place for ventilation; avoid installing on shaky place and try to

stay away from heat device.

Recommend operating environment

-20°C～60°C

Hardware installation steps

Please make sure LAN and WAN are working in order before installation of the Network High Speed Dome. After checked all the

network system in good condition, keep your hands clean and dry, following the steps below.

 Unpack the box to check the goods

 Take out all goods which needed for installation from the box

 Take off the protection cover and insert the SD card. Please refer to the SD card installation steps below.

Remove the ornament

screws (2pcs), then take it off

Loosen the screws of

horizontal installation panel

(4pcs), then put up the panel

for a little

3

 Connect related cables according to need (Power line, network line, audio line etc.)

 Connect the power supply

Note:

 Please read the user manual carefully before the installation.

 Make sure to turn off all the power when install the camera

 Please confirm the power transformer, avoid the device damage with unmatched power source

Network connection

 LAN connection

Use one network line to connect Speed Dome with concentrator or switchboard of the LAN. As Figure below.

Users also can use one network line to connect IP Speed Dome with computer network card or switchboard.

 WAN connection

Use one network line to connect IP Speed Dome with router or XDSL Modem/Cable Modem. As Figure below.

Fig. Devices connection scenarios

router

web browser

switch

web browser

IP camera

Insert micro-SD card

(IPPTZ120IRD)

Insert micro-SD card

(IPPTZ130IRB)

Loosen the screws of back

cover (4pcs) and take off the

cover

4

 Connect the power supply

After connect the power source, the IP speed camera will start operation automatically.

Connection instruction

5

3. Operating Guide for Network High Speed Dome

Set the IE Browser

Because the high safety level of the IE browser, If you visit Network High Speed Dome for first time, Please set the IE browser.

Setting method: open the IE browser, click Internet Option into the "Security" page, click the "Custom Level" and then follow steps to

set the IE browser

6

Download and Install ActiveX

Users have to install ActiveX Control when visit Network High Speed Dome at the first time via IE browser.

Download and install the ActiveX:

Input the IP address of Network High Speed Dome (default IP: http://192.168.1.188) in Internet Explorer to enter into login page.

At the login interface, click “Download ActiveX”. As shown in Figure 3-1 :

Figure 3-1

Popup control installation information, click “Run”. As shown in Figure 3-2:

Figure 3-2

A file download dialog will pop out, click “Install” to installation. As shown in figure 3-3:

Figure 3-3

7

Click “Finish” to complete the ActiveX installation. As shown in figure 3-4:

Figure 3-4

Login

Reopen Internet Explorer after ActiveX installation completes, input IP address (http://192.168.1.188) of the Network High Speed then

turn to login page, input username (default is admin) and password (default is blank), click login to enter into main interface (as shown in

Figure 3-5)

Figure 3-5

8

Live view

Live preview interface as shown infigure 3-6:

Figure 3-6

In the Live view interface, users can do remote operations such as master/slave stream video preview, voice intercom, listen,

Record, full-screen preview, Snap picture, PTZ control, preset, area scan, pattern scan, PTZ watch, preview video image volume adjustment,

Day/Night switch, Image Flip, Image Mode, etc.

 Master/slave stream: notice the buttons at the left lower corner, click it to switch the preview mode.

 Voice intercom: connect a sound box at the device voice output port, then connect a mike at the PC port. Click microphone icon

, then adjust the volume, the voice intercom between PC and Network High Speed Dome can be performed.

 Listen: connect a sound pick-up at the device audio input port, click the audio icon , users can call real time monitoring at PC

port.

 Snap picture: click icon to do screen video capture, it will create BMP picture and store in the specified folder automatically.

The default file storage path is C:\IPCamera, users can set it at the Setting→Local→Local setting .

 Full screen: click icon to get full screen preview, press ESC or right mouse click to exit full screen preview.

 Record: click icon to do manual video operation and store in the specified file automatically (Video format is mp4, the default

file storage path is C:\IPCamera\, users can set it at the Setting→Local→Local setting .

 3D positioning: 3D position function can be opened or closed.

 Switch the sidebar: click or icon to switch to the sidebar.

 Image parameters adjustment: Users can adjust the image parameters at the video preview interface, such as image brightness,

hue, contrast, saturation and sharpness, etc. as shown in Figure 3-7:

9

Figure 3-7

 Day/Night switch: according to the surveillance need, users can set color model, black model, auto model. As shown in Figure 3-8:

Figure 3-8

 Image Flip: via the buttons to adjust image rotation, support horizontal rotation , horizontal+vertical rotation . As shown

in Figure 3-6.

 Image Mode: Divided into outdoor, indoor, three models automatically, the default for auto. As shown in Figure 3-6.

Click PTZ at the video preview interface to turn to PTZ configuration interface. As shown in

Figure 3-9:

Figure 3-9

 PTZ control: user can do horizontal 360°/vertical 90°overall monitoring via PTZ configuration buttons , PTZ operation

speed 1-63 levels adjustable

 Area scan: via the PTZ buttons to set area scan, click to set left limit, click to set right limit and area scan

remembered automatically. Click to call area scan. As shown in Figure 3-9.

10

 PTZ Watch: at the PTZ Watch drop down list, users can select the PTZ watch type (Include close, preset, CRZ, pattern, area, etc)

and set the idle time, then click to save it. As shown in Figure 3-10.

Figure 3-10

 Preset: adjust the camera to the appointed angle and location through directional buttons, and then select a preset number in the

preset drop down list, click to set it. There are 1-255 presets can be set, and users can click to delete the preset, click

to call the preset. As shown in Figure 3-9.

 Pattern scan: at the pattern scan drop down list, users can select the pattern scan number, and edit the pattern scan name. Then

click to start recording, click to stop recording, pattern scan remembered automatically. Click to call pattern

scan. As shown in Figure 3-9.

 CRZ: At the CRZ drop down list, users can select cruise number, click to add preset, set the delay time. Select preset ID and

click to delete it. Finally click to save it and click to call cruise. As shown in Figure 3-11.

Figure 3-11

11

System specification setting

System

Basic info

1) System information

Click Setting→ System→ Basic info→ Sysinfo, IP Speed Dome “Sysinfo” interface. As shown in figure 3-12:

Figure 3-12

 Device Name: edit the camera name

 Device Number: display the device serial number

 Hardware Version: display the device hardware version number

 UBOOT Version: display the product system UBOOT version number

 Kernel Version: display the product system kernel version number

 App Version: display the product software version and the system version date

 PTZ Version: display the IP speed dome version model

 OCX Version: display the OCX version number

Note:Based on the version information which displayed in factory product

After setting complete, click to save it.

12

2) System operate

Click Setting→ System→ Basic info→ Sysoperate, IP Speed Dome “System operate” interface. As shown in figure 3-13:

Figure 3-13

 Reset: Restore factory settings

 Reboot: click to do IP speed dome reboot operation

 Parameters type: select the parameters type which you have to derive

 Parameter input: select the configure file which you need and click

 Parameter output: select the configure file which you need and click

After setting complete, click to save it.

13

3) Update

Click Setting→ System→ Basic info→ Update, IP Speed Dome “Update” interface. As shown in figure 3-14:

Figure 3-14

 System update: system update online.

Operation method:

① Click ,find the specified file and select the upgrade package. As shown in Figure below:

② Click , system upgrade automatically;

③ After system upgrade successfully, the following window will pop out, click . As Figure below:

④ Reopen the IE browser and input the IP address, after log in, check the whether the software version is updated.

14

Note: after system upgrade successfully, you need to reset camera data in "Sysoperate",clear IE cache and install

ActiveX again before logging in web system. (Clear IE cache as Figure below)

4) Log query

Click Setting→ System→ Basic info→ Log Query, IP Speed Dome “Log Query” interface, as shown in Figure 3-15:

Figure 3-15

 Type: select the alarm log type, all/ alarm/ exception/ operation/ information are optional

 Begin time/ End time: set the log search time period, click icon and the log information will display.

After setting complete, click to save it.

Non-professional technicians do not operate the system upgrade.

Please do not power off during installing update.

15

User manage

Click Setting→ System→Usermanage, IP Speed Dome “UserManage” interface, as shown in Figure 3-16:

Figure 3-16

 Add user: add a new user and select the new user limits of authority

 Modify: select the added user and modify the user password

 Delete: delete the added user

After setting, click to save it.

PTZ Config

1) Serial setting

Click Setting→ System→ PTZ Config→ SerialSetting, IP Speed Dome “SerialSetting” interface, as shown in Figure 3-17:

Figure 3-17

16

 Address: click to select or modify the camera address

 Baud rate: click to select or modify the baud rate

 Protocol: click to select or modify the protocol

After setting, click to save it.

2) Schedule Task

Click Setting→ System→ PTZ Config→ Schedule Task, IP Speed Dome “Schedule Task” interface, as shown in Figure 3-18:

Figure 3-18

 Start time: click the checkbox to turn on or turn off Schedule task

 Task restart: set the restart time if schedule task was broken off

 Cur setting: set the current schedule task time, max 10 periods/ day.

After setting, click to save it.

La page est en cours de chargement...

Comelit IPPTZ120IRD Manuel utilisateur

Ce manuel convient également à

Comelit IPPTZ120IRD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents