Jotul Stove Gas Stove Manuel utilisateur

Marque: Jotul

Modèle: Stove Gas Stove

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Gas Stove

Installation

and

Operation

Instructions

GF 400 BV Sebago

Gas Stove

IF THE INFORMATION IN THESE INSTRUCTIONS

ARE NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS AND LIQUIDS IN THE VICIN-

ITY OF THIS OR ANY OTHER APPLIANCE.

INSTALLATION:

INSTALLATION AND SERVICE MUST BE PER-

FORMED BY A QUALIFIED INSTALLER, SERVICE

AGENCY OR LICENSED GAS SUPPLIER.

WHAT TO DO IF YOU SMELL GAS:

• DO NOT TRY TO LIGHT ANY APPLIANCE.

• DO NOT TOUCH ANY ELECTRICAL SWITCHES.

• DO NOT USE THE PHONE IN YOUR BUILDING.

IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A

NEIGHBOR’S PHONE.

• FOLLOW YOUR GAS SUPPLIER’S INSTRUCTIONS.

• IF YOU CANNOT REACH YOUR GAS SUPPLIER,

CALL THE FIRE DEPARTMENT.

WARNING:

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED PLUMBER OR GAS-FITTER WHEN

INSTALLED IN THE COMMONWEALTH OF

MASSACHUSETTS.

A CARBON MONOXIDE (CO) DETECTOR SHALL

BE INSTALLED IN THE SAME ROOM AS THE

APPLIANCE.

AVERTISSEMENT:

ASSUREZ-VOUS DE BIEN SUIVRE LES INSTRUC-

TIONS DANS CETTE NOTICE POUR REDUIRE AU

MINIMUM LE RISQUE D’INCENDIE OU POUR EVITER

TOUT DOMMAGE MATERIEL, TOUTE BLESSURE OU

MORTALIT’E.

NE PAS ENTREPOSER NI UTILISER D’ESSENCE NI

OU LIQUIDES INFLAMMABLES DANS LE VOISINAGE

DE CET APPAREIL OU DE TOUT AUTRE APPAREIL.

L’INSTALLATION LE SERVICE DOIVENT ETRE

EXECUTES PAR UN INSTALLATEUR QUALIFIE,

AGENCE DE SERVICE OU LE FOURNISSEUR DE

GAZ.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ.

• NE PAS TENTER D’ALLUMER L’APPAREIL

• NE TOUCHEZ A AUCUM NTERRUPTEUR.

• NE PAS VOUS SERVIR DES TELEPHONES SE

TROUVANT DANS LE BATIMENT OU VOUS VOUS

TROUVEZ.

• APPELEZ IMMEDIATEMENT VOTRE FOURNISSEUR

DE GAZ CHEZ UN VOISIN. SUIVEZ LES INSTRUC-

TIONS DU FOURNISSEUR.

• SI VOUS NE POUVEZ REJOINDRE LE

FOURNISSEUR DE GAZ, APPELEZ LE SERVICE DES

INCENDIES.

Welcome to Jøtul...

Congratulations on the purchase of your new

Jøtul GF 400 BV Sebago gas stove.

We at Jøtul are glad you’ve made the decision to

warm your hearth with a Jøtul product. Your new

stove exemplifies our experience gained over 150

years as the world’s largest manufacturer of solid

fuel burning appliances. We’ve been building fine

quality cast iron stoves and fireplaces continuously

since 1853.

The Jøtul GF 400 BV Sebago combines advanced gas

technology with the warm, traditional elements of

cast iron. With proper care and use, your stove will

provide you with many years of safe, dependable and

satisfying service.

Please take a few minutes to familiarize yourself

with this manual and the features of your new Jøtul

fireplace.

Table of Contents

Service Tools .............................................. 4

Specifications ........................................... 4

General Information ............................... 5

Safety Information .................................. 6

Installation Requirements

Location ................................................. 6

Hearth Protection .............................. 6

Clearances ............................................ 7

Mantel & Trim ..................................... 7

Alcove..................................................... 7

Vent Requirements ............................... 10

Fuel Conversion...................................... 11

Gas Connection ...................................... 13

Gas Pressure............................................ 14

Log Set Installation ............................... 15

Flame Adjustment................................. 16

Wall Thermostat .................................... 16

Remote Control ...................................... 16

Decorative Pipe ...................................... 17

System Check.......................................... 17

Operation ................................................. 18

Maintenance........................................... 19

Glass Replacement ............................ 19

Optional Blower ..................................... 20

Optional Antique Brick Kit .................. 22

High Altitude Adjustment .................. 23

Illustrated Parts Breakdown ............... 24

Replacement Parts List......................... 25

Lighting Instructions ............ Back Cover

Jøtul GF 400 BV

Sebago

Gas Heater

Manufactured and Distributed by:

Jøtul A.S.A.

Fredrikstad, Norway

Jøtul North America

Gorham, Maine U.S.A.

Test Standards

This appliance complies

with National Safety

standards and is tested

and listed by Intertek

Testing Services of

Middleton, Wisconsin to

ANSI Z21.88-2002 • CSA 2.33-M02 and CAN/

CGA 2.17--M91, CSA P.4.-01.2 for Canada.

DO NOT ATTEMPT TO ALTER OR MODIFY THE

CONSTRUCTION OF THE APPLIANCE OR ITS

COMPONENTS. ANY MODIFICATION OR ALTER-

ATION WILL VOID THE WARRANTY, CERTIFICA-

TION AND LISTING OF THIS APPLIANCE.

THIS PRODUCT MUST BE INSTALLED

BY A LICENSED PLUMBER OR

GAS-FITTER WHEN INSTALLED IN THE

COMMONWEALTH OF MASSACHUSETTS.

THIS OWNER’S MANUAL PROVIDES

INFORMATION TO ENSURE SAFE INSTALLATION

AND EFFICIENT, DEPENDABLE OPERATION OF

YOUR FIREPLACE INSERT. PLEASE READ THESE

INSTRUCTIONS IN THEIR ENTIRETY AND MAKE

THEM AVAILABLE TO ANYONE USING OR

SERVICING THIS GAS INSERT.

M.E.A. 369-04-E

GF 400 BV Sebago

Specifications

The Jøtul GF400 BV Sebago is a atmospherically-

vented gas fireplace heater designed only for

vertical venting directly to the outside of the house,

using listed, Type B-vent pipe.

Input Rates

Natural Gas

40,000 BTU/hr. maximum input

22,000 BTU/hr. minimum input

Propane

40,000 BTU/hr. maximum input

20,000 BTU/hr. minimum input

Inlet Pressure: MIN MAX

Natural Gas: 5.0 WC (1.24 kPa) 7.0 WC (1.74 kPa)

Propane: 12.0 WC (2.99 kPa) 14.9 WC (3.71 kPa)

Manifold Pressure: MIN MAX

Natural Gas: 1.2 WC (.30 kPa) 3.8 WC (.95 kPa)

Propane: 2.9 WC (.722 kPa) 11.0 WC (2.74 kPa)

Piezo Ignitor / Standing Pilot

Suggested Tools for

Installation and Service

• External regulator (for Propane only)

• Piping which complies with local code

• Manual shutoff valve (T-Handle in Massachusetts)

• Sediment trap - if required by code

• Tee joint

• Pipe wrench

• Pipe sealant

• 10 mm open end wrench

• 1/2”, 7/16” open end wrench or deep socket

• Phillips head screwdriver

• Flat head screwdriver

• 1/4” nut driver

• 4 mm allen wrench

• Gloves

• Safety glasses

• Torx T20 screwdriver

• Leak test solution

• Reciprocating Saw

• Power Drill

THIS FIREPLACE IS SHIPPED FROM THE FACTORY

FOR USE WITH NATURAL GAS ONLY. FOR USE WITH

PROPANE, THE APPLIANCE MUST FIRST BE

CONVERTED USING #156003 FUEL CONVERSION KIT

PROVIDED. CONVERSION SHOULD BE MADE

BEFORE THE APPLIANCE IS INSTALLED. SEE PG. 11.

With Short Legs, reduce height by 2 1/4” ( 51 mm)

General Information

 THIS HEATER MUST BE INSTALLED AND MAINTAINED

BY A QUALIFIED SERVICE AGENCY.

 The installation and repair of this appliance must be

done by a qualified service person. Failure to

properly install and maintain this heater could result

in an unsafe or hazardous installation, which may

result in a fire, explosion, property damage, personal

injury or loss of life.

 This appliance may be installed in an aftermarket

permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type(s) of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certi-

fied kit is used.

Cet appareil peut être installé dans un maison

préfabriquée (mobile) déjà installée à demeure si les

règlements locaux le permettent.

Cet appareil doit être utilisé uniquement avec les

types de gas indiqués sur la plaque signalétique. Ne

pas l’utiliser ave d’autres gas sauf si un kitde conver-

sion certifié est installé.

 This appliance should be inspected before use and at

least annually. More frequent cleaning may be

required due to excessive lint from carpeting,

bedding material, etc. It is imperative that control

compartments, burners, and circulating air passage-

ways of the appliance be kept clean.

 THIS APPLIANCE MUST NOT BE CONNECTED TO A

CHIMNEY OR FLUE SERVING ANY OTHER APPLIANCE.

 The installation must conform to local codes. Your

local Jøtul dealer can assist you in determining what

is required in your area for a safe and legal installa-

tion. Some areas require a permit to install a gas

burning appliance. Always consult your local

building inspector, or authority having jurisdiction,

to determine what regulations apply in your area.

 CODE COMPLIANCE: Your local officials have final

authority in determining if a proposed installation is

acceptable. Any requirement that is requested by

the local authority having jurisdiction, that is not

specifically addressed in this manual, defaults to

local code. In the absence of local codes, the installa-

tion requirements must comply with the current

edition of National codes. In the U.S., these require-

ments are established in the National Fuel Code,

ANSI Z223.1.(NFPA 54) current edition. In Canada,

the codes have been established in CAN/CGA B149

Fuel Installation Code, current edition.

Glass Panel

Do not operate this appliance with the glass

front removed, cracked, or broken. Replacement

of the glass should be done by a licensed or

qualified service person. Only remove glass for

routine service. Always handle glass carefully.

Consult the local or national installation code(s) to

assure that adequate combustion and ventilation air

is available.

 Installer l’appareil selon les codes ou reglements

locaux, ou, en l’absence de tels reglements, selon les

Codes d’installation CAN/CGA-B149.

 DO NOT OPERATE THIS STOVE IF ANY PART HAS BEEN

UNDER WATER. Call a qualified service technician to

inspect the heater and to replace any part of the

control system and any gas control which may have

been under water.

 Ne pas se servir de cet appareil s’il a ete’ plonge dans

l’eau, completement ou en partie. Appeler un

technicien qualifie pour inspecter l’appareil et

remplacer toute partie du syste’me de controle et

toute commande qui ont ete plonges dans l’eau.

Hardware Bag Contents

• Fuel Conversion Kit - LP................................ 156005

• Decorative Pipe Mounting Brackets (4) .. 129469

Unpacking your stove

1. Remove the Top Plate of the stove by simply lifting it

straight off of the stove body.

2. To open the firebox, disengage the two Glass Frame

Latches located on top of the firebox. Pull each handle

forward to clear the latch from the notch in the

frame.

3. Familiarize yourself with the installation require-

ments specified in this manual, before beginning the

installation.

Glass Frame

Latch

Location

In selecting a location for the stove, consider the

following points:

1) Heat distribution

2) Vent termination requirements

3) Gas supply line routing

4) Traffic areas, furniture, draperies, etc.

The GF 400 BV may be located on or near conven-

tional construction materials, however, proper clearance

to combustibles must be maintained in order to provide

adequate air circulation around the appliance. Also, it is

important to provide adequate access around the stove

for servicing and proper operation.

The clearance and hearth specifications listed in this

manual are the minimum requirements for combustible

material. A combustible material is anything that can

burn (i.e. sheet rock, wall paper, wood, fabrics etc.). These

surfaces are not limited to those that are visible and also

include materials that may be located behind non-

combustibles.

If you are not sure of the combustible nature of a

material, consult your local fire officials. “Fire Resistant”

materials are considered combustible: they are difficult

to ignite, but will burn. Also, “fire-rated” sheet rock is

considered combustible.

Hearth Requirements

The GF 400 BV gas stove CANNOT be installed directly on

carpeting, vinyl, linoleum or Pergo

If this appliance will be installed on any combustible

material OTHER THAN WOOD, a floor pad must be

installed that is either metal or wood, or a listed hearth

pad. This floor protection must extend the full width

and depth of the appliance. It is not necessary to remove

carpeting, vinyl or linoleum from underneath the floor

protection. See fig. 1.

Safety Information

During normal operation, the GF 400 BV gas stove will

reach high surface temperatures. Therefore:

 Due to the high operating temperatures, this appli-

ance should be located out of traffic areas and away

from furniture and draperies.

 Children and adults should be alerted to the hazards

of high surface temperatures and should stay away to

avoid burns and/or clothing ignition.

 Young children should be supervised while they are in

the same room as the GF 400 BV gas stove.

 Clothing or other flammable materials should not be

placed ON or NEAR the GF 400 BV gas stove.

Surveiller les enfants. Garder les vetements, les

meubles, l’essence ou autres liquides a vapeur

inflammables loin de l’appareil.

 NEVER store or use gasoline or any other flammable

vapors or liquids in the vicinity of the GF 400 BV gas

stove.

 Never burn any other materials in your GF 400 BV

Sebago gas stove, it is strictly designed for use with

natural gas or propane fuel ONLY.

·Any safety screen, glass or guard removed for servic-

ing the appliance must be replaced prior to operating

the appliance.

Figure 1. Minimum Hearth Protection.

14”

(356 mm)

27”

(686 mm)

Vent Requirements

The GF 400 BV Sebago is specifically designed to operate

using 4” Type B vent pipe components or a Listed Flexible

gas liner.

• All venting components must be installed in accor-

dance with the terms of their listing and

manufacturer’s instructions.

• The minimum height of a vertically terminated

system shall be no less than 7', and the maximum

height shall be no more than 35'. See diagrams page

• With steep roofs, nearby trees, and in predominant

windy conditions, poor draft or down draft conditions

can occur. In these cases, increasing the height of the

vent or high wind termination caps may improve the

situation.

• ELBOWS: If an offset or elbow is necessary in the

vertical rise, it is important to support the vent pipe

every three feet, to avoid excessive stress on the

offsets.

• Whenever possible use 45° elbows opposed to 90°

elbows. This offers less restrictions for the flow of flue

gases.

Maximum number of 90° elbows: three

Maximum number of 45° elbows: four

• TOTAL MAXIMUM HORIZONTAL RUN ANYWHERE IN

THE VENTING CONFIGURATION IS 4 FEET. The distance

between any 45° elbows is considered a horizontal

run. See diagrams, page 10.

• Any Type B vent passing through a roof

must have a

flashing, storm collar, thimble and a Type B cap is

required. See diagrams, page 10.

• Venting on the Sebago CANNOT be less than 4” in

diameter or greater than 4” in diameter.

•Any unused flue or masonry enclosure can be used as

a passage way for venting, but the flue must be

relined using Type B 4” vent or Listed Flexible Gas

Liner.

• The remaining space around the liner in a masonry or

zero-clearance flue CANNOT be used to vent any other

appliance.

• When terminating through the roof refer to the Gas

Vent Rule for proper vent termination height.

See fig. 5.

• NO venting may terminate horizontally or below

roof eaves.

• Passage through combustibles (walls, ceilings) must

be with Type B venting and must maintain listed

clearances. The GF 400 BV Sebago stove is approved

for use only with 4” Simpson Dura-Vent Wall

Thimble #3143 to maintain proper vent clearances.

• Any horizontal run should have an upward slope of

1/4” per foot toward the termination cap.

• When venting through a thimble into a masonry

flue, any venting exposed in the room must be Type

B venting, or a flexible liner sleeve within 24 ga. 6”

stove pipe.

• Listed Flexible Gas Liners may not be exposed in any

living space.

Figure 5. Termination Height Requirements.

• When 6” diameter decorative pipe is installed to

cover the venting any Listed Flexible Gas liner must

be connected directly to the stove’s draft hood.

• Use of single wall connector pipe as a vent is

prohibited for use with the GF400 Sebago B-Vent

stove.

• A firestop is required at every floor.

• Any venting that is exposed above the first floor,

regardless of attic space or living space, must be

enclosed. Always maintain the required clearance

from all sides of the vertical vent system according

to manufacture.

• Installation of any components not manufactured or

approved by Jøtul or failure to meet all clearance

requirements will void all warranties and could result

in property damage, bodily injury, or serious fire.

• Never modify any venting component, or use any

damaged venting product.

• THE GAS APPLIANCE AND VENT SYSTEM MUST BE

VENTED DIRECTLY TO THE OUTSIDE OF THE BUILD-

ING, AND NEVER ATTACHED TO A CHIMNEY SERV-

ING A SOLID FUEL OR GAS BURNING APPLIANCES.

• BE SURE TO MAINTAIN THE PROPER CLEARANCES TO

COMBUSTIBLES AS DEFINED IN THIS MANUAL AND

IN THE INSTRUCTIONS PROVIDED WITH EACH

VENTING COMPONENT.

• When installing at an altitude above 2000’ the

minimum vertical rise

becomes 12’ from the draft

hood.

Figure 6. GF 400 BV venting through a masonry

chimney.

Listed

termination

cap required

Storm collar

required

Recommended

damper sealing plate

to seal flue chamber

to prevent heat loss

Always

maintain the

proper

clearance to

mantel and

trim

Maximum

offset is 4 ft.

Type B vent or

Listed Flexible Gas

Liner.

Use of Type B vent

liner within outside

chimneys is

recommended to

help keep the gases

warm and stabilize

draft.

Max. Height 35 ft.

Min. Height 7 ft.

Top sealing

achor plate

WARNING: FAILURE TO POSITION THE

PARTS IN ACCORDANCE WITH THIS

DIAGRAM OR FAILURE TO USE ONLY PARTS

SPECIFICALLY APPROVED WITH THIS

APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

Venting through a Masonry or

Prefabricated Manufactured

Chimney

NOTE:

A chimney system located outside the building

envelope may be subject to downdrafting

and/or flow reversal. Atmospherically-vented

appliances, such as B-Vents, may not be compat-

ible with these chimney systems.

All atmospherically-vented appliances (B-Vents)

are affected by atmospheric conditions and

house pressurization. For example, a B-Vent

appliance vented to an outside chimney system

in a basement will likely be subject to negative

pressure. This type of installation is not recom-

mended.

Fuel Conversion Procedure

1. Turn off gas supply to stove.

2. Remove the stove Top Plate.

3. Disengage the two Glass Frame Latches at the top of

the firebox. See illustration on page 5. Carefully lift

the glass panel up and out of the stove.

4. If installed, remove the Embers and Log Set using

care not to damage the fragile log parts.

5. Lift out the Burner Skirt shown in fig.11.

6. Reach under the stove and remove the Air Shutter

wingnut from its stud. See fig. 12.

Conversion Kit Contents:

• 1, regulator tower labeled for propane

• 3, regulator tower screws

• 1, burner orifice (3.20 mm for NG, #49 for LPG)

• 1, pilot orifice (#51 for NG, #30 for LPG)

• Label A - to be completed and applied to

the back of the stove

• Label B - apply to the stove’s Rating Plate

• Small valve label - apply to valve body

Conversion instructions are also shipped in the stove with

the conversion kit.

Fuel Conversion

The GF 400 BV gas stove is shipped from the factory

equipped to burn NATURAL GAS only. If PROPANE gas is

to be used as fuel, the appliance must first be converted

for use with propane. Use Propane Conversion Kit

156003, supplied with the appliance.

Order and install NG Conversion Kit 156004 to

change back to use with natural gas.

WARNING:

THE CONVERSION KIT IS TO BE

INSTALLED BY AN AUTHORIZED JØTUL

SERVICE TECHNICIAN IN ACCORDANCE

WITH THE MANUFACTURER’S

INSTRUCTION AND ALL CODES AND

REQUIREMENTS OF THE AUTHORITY

HAVING JURISDICTION. FAILURE TO

FOLLOW THESE INSTRUCTIONS COULD

RESULT IN SERIOUS INJURY OR

PROPERTY DAMAGE. THE QUALIFIED

AGENCY PERFORMING THIS WORK

ASSUMES RESPONSIBILITY FOR THIS

CONVERSION.

IN CANADA:

THE CONVERSION SHALL BE CARRIED

OUT IN ACCORDANCE WITH THE RE-

QUIREMENTS OF THE PROVINCIAL AU-

THORITIES HAVING JURISDICTION AND

IN ACCORDANCE WITH THE REQUIRE-

MENTS OF THE CAN1-B149.1 AND .2

INSTALLATION CODE.

AVERTISEMENT:

Cet equipement de conversion sera installe par

une agence qualkfiee de service conformenment

aux instructions du fabricant et toutes exigences

et codes applecables de l’autorises avoir la

juridiction. Si l’informaiton dans cette Instruc-

tion n’est pas suivie exactement, un feu, explo-

sion ou production de protoxyde de carbone peut

7. Lift out the Burner Plate: NOTE: There are no screws

securing the Burner to the floor of the firebox. Pull the

Air Shutter forward and lift the burner together with

shutter up and out of the stove as a unit. See fig. 13.

8. Change the Burner Orifice. Using a ½” open ended

wrench or deep-well socket, remove the burner

orifice from its brass elbow housing and replace with

the appropriate orifice supplied in the kit. See fig. 14.

9. Replace the Air Shutter and push it all the way back

to allow replacement of the Burner Plate. Reattach

the wingnut and gasket to the shutter stem under

the stove, but do not tighten. You will set its final

position later.

10. Replace the Burner Plate. Engage the burner tube

with the Air Shutter assembly as in fig. 14. Be sure

the burner is securely engaged with the two support

brackets at the front of the firebox and push the

plate back toward the rear of the firebox.

11 . CHANGE THE PILOT ORIFICE: From within the

firebox, remove the Pilot Head by pulling it straight

up from the pilot base. See fig. 16. Using the 4 mm

hex key included with the kit, unscrew the pilot orifice

(counterclockwise). Replace with the appropriate

orifice:

12. Tighten orifice into the base of the pilot assembly. To

prevent bypass leaks, be sure the orifice is secured

tightly and flush with the base. Replace pilot head by

pushing it down onto the pilot base.

13. Replace the Variable Regulator. Using a Torx T-20

screwdriver, remove the three screws from the front

of the valve regulator. See fig. 17.

14. Remove the regulator tower, gasket, white plastic

disk, and spring. See fig. 17.

Figure 13. Remove the Air Shutter and Burner as a unit.

Gas Supply Connection

The gas supply line connection is made to the left side of

the front-mounted valve. The gas supply line should be

3/8" npt with a 1/2" diameter supply, or the appropriate

size to provide sufficient gas pressure to the valve

regardless of the input setting.

The use of Flexible Gas Appliance Connectors is

acceptable in many areas in the U.S. However, Canadian

methods vary depending on local code.

ALL INSTALLATIONS MUST COMPLY WITH LOCAL

CODE OR IN THE ABSENCE OF LOCAL CODE, MUST

COMPLY WITH THE MOST RECENT EDITION OF THE

NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA 54 OR

CAN-B149.

All codes require a gas shut-off valve (gas cock) and

union, to be installed in the supply line, and in the same

room as the appliance. This allows for the disconnection

of the stove for servicing and maintenance. See fig. 18.

A T-HANDLE GAS COCK IS REQUIRED IN

MASSACHUSETTS TO COMPLY WITH

CODE 248CMR.

Secure all joints tightly using appropriate tools and

sealing compounds. For propane units be sure to use

compounds that are propane resistant. Turn on gas

supply and test for gas leaks using a soapy water solution.

Never use an open flame to check for leaks.

15. Install the new regulator: Be sure the new gasket is

properly positioned and tighten screws securely.

16. Install the identification labels to the stove so that they can

be seen by any person that may be servicing the stove.

Label A: apply to back of stove.

Label B: apply to stove’s rating plate.

Small valve Label: apply to valve.

17. Reassemble the stove, apply gas to the system and

check for leaks using a soapy water solution or

electronic gas detector.

NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

18. Correct gas pressure is essential for efficient and safe

operation of this appliance. Use a manometer to

check pressures as specified in the Gas Pressure

section of this manual (page 15).

19. Adjust the Air Shutter. You will need to position the

shutter to provide a gas/air mixture that will achieve

the best flame picture with your particular installa-

tion. Start with the shutter stem at the half-way

position in the slot in the bottom of the stove. See

fig. 12. Pushing the stem back will restrict air, while

pushing it forward will open the shutter and in-

crease air. With some experimentation, you will find

the shutter position that works best for your installa-

tion.

ALWAYS REFER TO THE LIGHTING INSTRUCTIONS ON THE

INSIDE BACK COVER OF THIS MANUAL WHEN LIGHT-

ING YOUR STOVE.

BLOWER NOTE: Install the optional blower before

connecting the gas line in order to ensure adequate

clearance between both.

Valve

Figure 17 Regulator assembly.

Remove black gasket

from regulator assembly

Regulator Tower

Pilot Head

Orifice

Pilot Base

Figure 16. Pilot orifice removal and replacement.

Retainer

Clip

Gas Pressure

Correct gas pressure is essential for efficient and safe

operation of the GF 400 BV gas stove. It is important

that the correct pressure is established at the time of

the installation. Proper gas pressure provides a

consistent flow of gas to the appliance and is instru-

mental in checking for gas leaks.

Pressure Test: Attach a manometer to the appro-

priate test point on the valve. See fig. 19. The gauge

connections are located on the front of the valve

under the On/Off/Pilot- knob. Gauge connections are

identified by:

E - for Inlet or Supply Pressure (the amount of

gas coming to the valve.)

A - for Manifold Pressure (the amount of gas that

is coming out of the valve to the burner.)

ALWAYS TEST PRESSURES WITH VALVE CONTROL

KNOB SET ON HIGH.

INLET GAS PRESSURES

(inches water column)

MIN MAX

NATURAL GAS 5.0 7.0

PROPANE 12.0 14.9

The appliance and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing on that system

at test pressures in excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas

supply line by closing its individual manual gas

shut-off valve (gas cock) during any pressure

testing of the gas supply piping system that is

equal to or less than pressures of 1/2 psig (3.5 kPa).

MANIFOLD PRESSURES

(inches water column)

MIN MAX

NATURAL GAS 1.2 3.8

PROPANE 2.9 11.0

Figure 19. Pressure test points.

Leak test:

1. Mix a 50-50 solution of water and dish

soap.

2. Light appliance- see lighting instructions

on the inside back cover of this manual

or on the stove’s rating plate.

3. Brush or spray all joints and connections

with the soapy water solution.

4. If bubbles appear at any connection or

seam or a gas odor is detected, immedi-

ately turn gas control knob to the OFF

position.

5. Tighten or reconnect the leaking joint

and retest for any gas leaks.

Figure 18. Supply valve connection fittings.

Log Set Installation

Brick Kit Note: Install the optional Antique Brick Kit

155370 before installing the logset. See page 22 and

the instructions provided with that kit.

The GF 400 BV logset must be installed before operating

the burner. The logset includes six log pieces, and a bag

of ember stones packaged inside the firebox. To install

the log set, remove the packaging and place the parts

inside the firebox as illustrated in figures 20-24. Do not

handle the log set with your bare hands. Always wear

gloves to prevent skin irritation from the ceramic fibers.

The ember stones realistically simulate glowing

coals when the burner is operating. These should be

spread evenly over the burner plate and around the logs. DO

NOT OBSTRUCT THE PILOT ASSEMBLY OPENING. Do not pile

the embers against the burner skirt edges. See fig. 24.

Figure 20. Engage the holes in the underside ot the Right

Log with the peg in the burner skirt.

Figure 22. Install Left Log

Figure 23. Install Left Middle Log

Figure 24. Install Top Log

Figure 24a. Position embers loosely and maintain 1/4”

clearance from the burner skirt edges.

NOTE: You do not need to use all of the

ember stones. With experimentation, you will

find the arrangement and quantity of embers

that works best with your stove. Depending upon

the characteristics of your installation, it is

possible that too many ember stones can pro-

mote sooting on the logs. Adjust the quantity of

ember stones as appropriate to maintain the best

overall flame picture and burner performance.

THE CERAMIC FIBER LOGS AND GLOWING EMBERS CAN

IRRITATE YOUR SKIN. GENTLY WASH YOUR HANDS WITH

WARM SOAPY WATER AFTER HANDLING THE LOGS.

Open

Optional Wall Thermostat or

Remote Control

Use only a 750 millivolt DC two-wire circuit thermostat

with this appliance. The thermostat should be placed in

the same room as the heater, typically 5 feet off the

floor. Avoid drafty areas or any area that may affect the

accuracy of the thermostat.

The thermostat should be connected to the GF 400

BV using a minimum of 16 gauge wire with a maximum

length of 25 feet of wire.

Connect the two thermostat wire leads to the two

left terminals on the terminal block located directly

above the ignitor button. Do not overtighten the

connections. IT IS NOT NECESSARY TO DISCONNECT

ANY OTHER WIRES. See Fig. 26.

For thermostatic operation, the On/Off/T-Stat

switch on the back of the stove must be in the T-stat

position, and the pilot light must be running, as it is the

power source for the thermostat.

At the thermostat, the two wires should be con-

nected to the two connection screws on the thermostat

base plate per the manufacturer’s instructions.

Remote Control

When using a remote, the remote receiver should be

wired to the terminal block the same way the thermo-

stat would be. See the instructions above.

Follow the operating instructions included with the

Remote Control unit.

CAUTION:

LABEL ALL WIRES PRIOR TO DISCONNECTION

WHEN SERVICING THE CONTROLS. WIRING

ERRORS CAN CAUSE IMPROPER OR DANGEROUS

OPERATION. ALWAYS VERIFY PROPER OPERA-

TION AFTER SERVICING THE APPLIANCE.

Figure 26. Valve and Accessory wiring diagram.

Flame Appearance / Air Shutter

Adjustment

The GF 400 BV gas stove is shipped from the factory

equipped to burn Natural gas. If the stove has been

converted for use with propane, the Air Shutter may

require adjustment to achieve the desired flame appear-

ance. Other installation related variables can also affect

the flame picture. The Air Shutter may be opened or

closed to provide the best flame picture for your specific

installation.

Too large an air opening - the appliance will generate

a flame that is blue and transparent, or an “anemic”

flame.

Too small an air setting - the appliance will generate

very long yellow flames resulting in soot. Sooting pro-

duces black deposits on the logs, on the inside walls of

the appliance, and potentially on the exterior termination

cap. Sooting is caused by incomplete combustion in the

flames and lack of combustion air entering the air shutter

opening.

To adjust the air shutter:

1. Reach under the right side of the stove and loosen the

wingnut located closest to you. See fig. 25. Slide the

wingnut stud forward to open the air shutter and back

to provide less air. Make adjustments in small incre-

ments.

2. Tighten the wingnut to secure the shutter at the

desired setting.

3. Allow the stove to burn for 30 minutes on the HIGH

setting, observing the flame continuously. If the flame

appears weak, slow, or sooty, repeat the process

described above until the flame is as desired.

WARNING: AIR SHUTTER ADJUSTMENTS SHOULD ONLY

BE PERFORMED BY A QUALIFIED PROFESSIONAL SERVICE

TECHNICIAN.

Figure 25. Loosen the wingnut to adjust the air shutter.

VALVE

TERMINAL

BLOCK

THERMOPILE

ROCKER

SWITCH

OFF

TSTAT

Yellow

Purple

SPILL SWITCH

White

Orange

Red

Black

White

Black

OPTIONAL

THERMOSTAT

REMOTE

CONTROL

System Check

1. PURGING THE GAS LINE: When lighting the appli-

ance for the first time, it will take a few moments to

clear the gas line of air. Once this purge is complete,

the appliance will operate as described in the

lighting instructions. See the inside back cover of

this manual or the stove Rating Plate attached the

bottom of the stove. Subsequent burner starts will

not require purging the gas line unless the supply

line is shut off.

2. PILOT FLAME: You can monitor the pilot flame

through the view port located at the rear of the

Right Log. See fig. 28. The pilot flame should be

steady - not lifting or floating. The flame should be

blue in color around the pilot hood, with traces of

yellow toward the outer edges.

The pilot flame should engulf the top 3/8” of the

thermopile (to generate millivolt current) and the

top 1/8” of the thermocouple. The pilot flame

should project out of the pilot hood 1” at all three

ports. See fig. 28.

3. BURNER ADJUSTMENT: This stove is equipped with a

variable gas control valve that allows easy adjust-

ment of the flame height appearance and heat

output. To adjust the flame between the HI and

LOW setting, rotate the HI/LOW knob, located in the

center of the valve face. Fire intensity can be

adjusted up to 50% between the LOW and HIGH

settings. See fig. 29.

NO SMOKE OR SOOT SHOULD BE PRESENT. CHECK

LOG PLACEMENT IF ANY SOOT OR SMOKE IS

PRESENT. IF SOOT OR SMOKE PERSISTS, THE AIR

SHUTTER MAY NEED TO BE ADJUSTED.

See Air Shutter/Flame Appearance section of this

manual for proper air shutter settings and adjust-

ments. Note: the more offsets there are in the vent

system, the greater the need for an air shutter

adjustment. See page 16.

1

(25mm)

3/8

(8mm)

Min.

1/8

(3mm)

Min.

Figure 28. Proper pilot flame appearance.

Installing Decorative Pipe

The use of decorative pipe is optional. No decorative

pipe is included with the Jøtul GF 400 BV Sebago,

however, four locator brackets are included with

the stove in the hardware bag. The brackets are

used to center the decorative pipe over the draft

hood on which the pipe rests. Follow the procedure

below to attach the brackets to the stove.

1. Remove the four 1/4” hex head screws that

attach the 4” Flue Collar to the draft hood, but

do not remove the Flue Collar. See Figure 27.

2. Align the “L”- shaped pipe brackets with the

holes on the Flue Collar and attach using the

four 1/4” hex head screws, located in the Misc.

Hardware Bag.

Reminder: Do not use single wall stove pipe as the

vent pipe on this appliance.

Figure 27.

Decorative pipe attachment and Spill Switch location.

Operation

Familiarize yourself with the controls of the GF 400 BV.

Make sure that anyone else using the appliance is also

familiar with the controls and operation procedures.

Always follow the Lighting Instructions on the inside

back cover of this manual and also located on the Rating

Plate attached to the burner assembly.

1. Once the pilot is lit, burner operation is controlled by

the rocker switch located at the left corner of the rear

shroud. See fig. 30.

• ON / OFF - use for manual control of the burner.

• T-STAT - use for optional thermostatic or remote

control operation. The burner will be controlled by

those accessories.

2. During the first few fires, you may notice odor and/or

smoke from the stove. This is normal and results from

burn-off of manufacturing residue and curing of

materials. You may find it helpful to provide additional

ventilation and fresh air to alleviate this condition.

3. Condensation may occur on the glass upon each

lighting of the appliance. This “fog” will disappear as

the appliance heats up.

4. Keep the controls and the area under the appliance

free of debris, vacuum this area frequently. Always

keep the appliance area clear and free from combus-

tible materials, gasoline and other flammable liquids.

Figure 29. Flame appearance on the “high” setting after

approximately 15 to 20 minutes burning.

WARNING:

AIR SHUTTER ADJUSTMENTS SHOULD ONLY BE

PERFORMED BY A QUALIFIED PROFESSIONAL

SERVICE TECHNICIAN.

Figure 30. Burner

Switch and

Optional Blower

Controls

If a vacuum is used during any service on the stove,

ALWAYS be sure the stove is cold and there are NO hot

embers.

5. Remember, this appliance has a continuous burning

pilot flame. Exercise caution when using products

having combustible vapors. Always shut-off gas

supply while servicing the stove.

6. CAUTION: DO NOT OPERATE THIS APPLIANCE WITH

THE GLASS REMOVED CRACKED OR BROKEN.

Replacement of the glass should be done by a licensed

or qualified service person. Use only replacement

glass provided by your authorized Jøtul dealer. Never

use any substitute materials.

WARNING: OBSERVE CAUTION WITH THE GLASS. THE

GLASS PANEL MAY SHATTER UNEXPECTEDLY IF STRUCK

WITH AN OBJECT. ALWAYS HANDLE THE GLASS PANEL

WITH CARE. WHEN SERVICING THE STOVE ALWAYS

PULL THE GLASS ASSEMBLY STRAIGHT UP FOR RE-

MOVAL.

7. Clean the glass only when necessary. Wipe surface

with a clean, damp soft cloth. Follow with a dry, soft

towel as desired. Take care not to scratch the glass

surface.

WARNING: DO NOT USE ABRASIVE CLEANERS ON THE

GLASS. NEVER CLEAN THE GLASS WHEN IT IS HOT.

CAUTION:

DO NOT ATTEMPT TO ALTER THE FLAME

APPEARANCE BY POSITIONING THE GAS

VALVE CONTROL IN ANY OTHER POSITION

OTHER THAN THE FULL “ON” POSITION.

NOTE: This appliance is equipped with a Spill Switch

which will disable the burner in the event that the

vent system becomes blocked. Located on the side

of the Draft Hood, at the back of the stove, the

switch has a reset button that, when pressed, will

re-enable burner function. See Fig. 27.

If the Spill Switch repeatedly shuts the burner

off, turn off the gas supply and call your dealer or

service technician. The Spill Switch will continue to

shut off the burner until the vent problem has been

corrected. Not all vent problems can be corrected as

B-Vent appliances are affected by atmospheric

conditions and house pressurization.

BLOCKED FLUE SWITCH

Glass Care

Clean the glass only when necessary. Wipe the surface

with a clean, dampened, soft cloth. Follow with a dry,

soft towel. Take care not to scratch the glass surface.

WARNING:

DO NOT USE ABRASIVE CLEANERS ON THE

GLASS. NEVER CLEAN THE GLASS WHEN IT

IS HOT.

Gasket Inspection

It is important that the glass gasket be inspected at

least annually. Examine the ribbon gasket for signs of

deterioration and make sure the gasket has a positive

seal. Replace the gasket if necessary. Refer to the

replacement parts list on page 25.

FOR REPLACEMENT, USE ONLY JØTUL

CERAMIC GLASS REPLACEMENT KIT

155599. DO NOT USE ANY OTHER TYPE OF

GLASS WITH THIS APPLIANCE.

Figure 32. Wrap the gasket around the glass panel.

Maintenance

Your Jøtul GF 400 BV Sebago and its venting system

should be inspected before use and at least annually by

a qualified service technician.

Use the form on page 26 to keep a maintenance

history of your stove.

IMPORTANT:

ALWAYS TURN OFF THE GAS SUPPLY TO THE

FIREPLACE AND UNPLUG THE FORCED AIR

BLOWER BEFORE ANY SERVICE WORK IS

PERFORMED ON THE FIREPLACE.

Annual Cleaning

Vent System

The entire vent system, including the chimney, should

be inspected and cleaned every year. If the intake and

exhaust venting is disassembled for any reason, it

should be reassembled and sealed according to the

manufacturer’s instructions provided at the initial

installation.

Burner and Logset

Periodically inspect the Firebox, Valve Compartment,

Convection Airways and optional Blower to BE CERTAIN

THAT THE FLOW OF COMBUSTION AND VENTILATION

AIR IS UNOBSTRUCTED.

The firebox should be vacuumed annually to remove

any surface build up. Use a soft brush attachment and

handle the logs carefully as they are fragile. Be sure to

vacuum or wipe off the pilot assembly and burner

surfaces.

Glass Panel or Gasket Removal

1. Lift the Top Plate off of the stove.

2. Release the two Glass Frame Latches. Pull each latch

handle forward forward to disengage the latch from

the notches in the glass frame.

3. Lift the glass frame all the way up and out of the top

of the stove. Lay this assembly on a flat surface,

protecting the frame from scratches using a blanket

or towel.

3. The glass panel is held in place by four compression

clips. Use a screwdriver or small pliers to pry these up

off the edge of the glass retaining walls. See fig. 31.

4. Remove the old gasket material. See fig. 32.

Glass Panel or Gasket Replacement

1. Wrap the new gasketing material evenly around the

edge of the glass, peeling back the protective strip to

expose the adhesive as you go. Press the adhesive side

down onto the glass surface. Do not stretch the

gasket.

2. Place the gasketed glass within the frame and press

each of the retainer clips back into place on the

retainer walls.

Figure 31. Use small pliers remove the four clips.



 THIS BLOWER MUST BE

ELECTRICALLY GROUNDED IN

ACCORDANCE WITH LOCAL CODES

OR, IN THE ABSENCE OF LOCAL

CODES, WITH THE CURRENT ANSI/

NFPA 70, NATIONAL ELECTRICAL

CODE OR CSA C22.1-CANADIAN

ELECTRICAL CODE.



 THIS UNIT IS SUPPLIED WITH A

THREE-PRONG (GROUNDING)

PLUG FOR PROTECTION AGAINST

SHOCK HAZARD AND SHOULD BE

PLUGGED DIRECTLY INTO A

PROPERLY GROUNDED THREE-

PRONG RECEPTACLE. DO NOT

CUT OR REMOVE THE GROUNDING

PRONG FROM THE PLUG.



 ALWAYS DISCONECT THE POWER

SUPPLY WHEN PERFORMING ANY

SERVICE ON THE FIREPLACE

INSERT.

Optional Blower # 156000

Connect the gas supply line to the stove,

before installing the Blower.

Use a 90° Elbow off the control valve to create

clearance required for the blower installation.

1. Unpack and check the contents of the blower kit.

Contact your dealer if any damage is evident or

parts are missing. See fig. 33.

2. Attach the Snapstat Bracket to the studs located in

the middle of the firebox floor using the two M6

hex nuts and a 10 mm wrench. See fig. 34.

3. Attach the Blower Bracket to the stove using the

two M6 flange head hex bolts as shown in fig. 34.

4. Attach the Duct Deflectors using the two #7 x 1/2”

screws together with the finger guard mounting

screws already in place. See #7 and #11 in fig. 33.

5. Install the Blower with the duct openings oriented

up and forward. See fig. 35. Feed the wire harness

through the bracket opening and secure the blower

to the bracket with the wingscrew.

6. Attach either Snapstat wire connector to either

Snapstat terminal. See fig. 35.

7. Install the Snapstat by sliding it all the way into the

slot in the bottom of the Snapstat Bracket as shown

in figs. 34 and 35.

8. Connect the male wire harness connector to the

female wire harness connector already installed in

the stove. See fig. 35.

9. Connect power cord to outlet.

Figure 34. Attach Snapstat and Blower Brackets.

La page est en cours de chargement...

Jotul Stove Gas Stove Manuel utilisateur

Marque: Jotul

Modèle: Stove Gas Stove

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Gas Stove

Télécharger le PDF

rapport

dans d''autres langues

English: Jotul Stove Gas Stove User manual

Jotul Stove Gas Stove Manuel utilisateur

Ce manuel convient également à

Jotul Stove Gas Stove Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents