Savant QP1R30240 Guide d'installation

Marque: Savant

Modèle: QP1R30240

Taper: Guide d'installation

Savant Product Regulatory Statement | 009-1950-02

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

1 of 2

Important Safety Information - Read First!

Before installing, conﬁguring, or operating any equipment, all relevant technical documentation must be read,

understood, and followed. Savant technical documentation may contain important product-speciﬁc installation,

mounting, and safety instructions, and can be accessed through the Savant Store.

Scan the QR code or visit the URL below, enter the relevant product name or SKU in the Search Savant prompt, and

select the product purchased to ﬁnd documents, speciﬁcations and more.

https://store.savant.com/DefaultStore/ccrz__HomePage

Product Information and Regulatory Statement

Safety Statements

All safety instructions below must be read, understood, and

carefully followed under all applicable circumstances when

working with any Savant equipment.

1. Follow all input power ratings marked on product near power

input!

2. If fuse replacement is required, replacement fuse should match

fuse rating marked on the product.

3. Do not use equipment near water.

4. Clean only with dry cloth.

5. Do not block any ventilation openings or install near any heat

sources such as heat registers, stoves, radiators, ampliﬁers,

etc.

6. Refer all servicing to qualiﬁed service personnel. Servicing is

required when any part of the apparatus has been damaged in

any way, or fails to operate normally for any reason.

7. Use only attachments/accessories speciﬁed by the

manufacturer, following all relevant safety precautions for any

such attachments/accessories.

8. For applicable equipment, use the included power cord with

the grounding prong intact to insure proper grounding of the

device.

9. If the provided plug does not ﬁt the desired outlet, contact a

licensed electrician to replace the obsolete outlet.

10. Protect any power cord from being walked on, pinched,

strained, or otherwise potentially damaged, especially at the

outlet or device connections.

11. Disconnect any outlet powered apparatus from its power

source during lightning storms or when unused for long

periods of time.

12. To completely disconnect equipment from AC mains power,

disconnect the power supply cord plug from the AC

receptacle on the device.

13. For any hardwired or ﬁxed in-wall apparatus, carefully follow

all wiring diagrams and instructions. All electrical wiring

and servicing should be performed by a properly licensed

electrician.

Déclarations de Sécurité

Toutes les instructions de sécurité ci-dessous doivent être lues,

comprises et soigneusement suivies dans toutes les circonstances

applicables lorsque vous travaillez avec un équipement Savant.

1. Suivez toutes les puissances nominales indiquées sur le

produit près de la puissance absorbée!

2. Si le remplacement du fusible est nécessaire, le fusible de

remplacement doit correspondre à la valeur nominale du

fusible indiquée sur le produit.

3. N’utilisez pas d’équipement près de l’eau.

4. Nettoyer uniquement avec un chion sec.

5. Ne bloquez pas les ouvertures de ventilation et n’installez pas

à proximité de sources de chaleur telles que les registres de

chaleur, les cuisinières, les radiateurs, les ampliﬁcateurs, etc.

6. Conﬁez toutes les réparations à un technicien qualiﬁé.

Un entretien est requis lorsqu’une partie de l’appareil a

été endommagée de quelque manière que ce soit ou ne

fonctionne pas normalement pour une raison quelconque.

7. Utilisez uniquement les attachements / accessoires spéciﬁés

par le fabricant, en suivant toutes les précautions de sécurité

applicables à ces attachements / accessoires.

8. Pour l’équipement applicable, utilisez le cordon d’alimentation

inclus avec la broche de mise à la terre intacte pour assurer

une mise à la terre correcte de l’appareil.

9. Si la ﬁche fournie ne correspond pas à la prise souhaitée,

contactez un électricien agréé pour remplacer la prise

obsolète.

10. Protégez tout cordon d’alimentation contre les piétinements,

les pincements, les tensions ou autres dommages potentiels,

en particulier au niveau de la prise ou des connexions de

l’appareil.

11. Débranchez tout appareil alimenté par une prise de courant de

sa source d’alimentation pendant les orages ou lorsqu’il n’est

pas utilisé pendant de longues périodes.

12. Pour déconnecter complètement l’équipement du secteur,

débranchez la ﬁche du cordon d’alimentation de la prise

secteur de l’appareil.

13. Pour tout appareil encastré ou câblé, suivez attentivement

tous les schémas de câblage et les instructions. Tout le

câblage électrique et l’entretien doivent être eectués par un

électricien dûment agréé.

IMPORTANT NOTES:

• For product mounting, installation, safety instructions, technical speciﬁcations, and more, refer to the product Quick

Reference Guide, available via the link or QR code noted above.

• For regulatory and compliance information, see reverse of this sheet and/or product packaging.

Savant Product Regulatory Statement | 009-1950-02

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

2 of 2

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for CLASS B digital devices, pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try correcting the

interference with one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Connect this equipment to an outlet on a circuit dierent from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to

operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement - Wireless and Handheld Devices Only

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance of 20 cm between the radiator and your body.

FCC and IC Identiﬁer - Devices with Integrated Screen or User Interface Only

This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identiﬁer. This information can be

found on the device by accessing:

(Service menu) > About (A propos de)

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003/NMB-003.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful

interference.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested

built-in radios. The Country Code Selection feature is disabled for products marketed in the US/Canada.

Déclaration IC

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage, et

2. Cet appareil accepter toute interférence, y compris les interférences pouvant provoquer fonctionnement indésirable d’appareil.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux radiations de la FCC déﬁnies pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

Identiﬁcateur de la FCC et d’Lc

Ce périphérique par voie électronique ache le logo de déclaration de conformité FCC ainsi que l’identiﬁcateur de la FCC et d’IC. Cette

information peut être trouvée sur le terminal en accédant à:

(Menu de service) > About (A propos de)

Single 30 Amp Relay Companion Module - QRG | 009-2112-00 1 of 4 45 Perseverance Way, Hyannis MA 02601

DO NOT

PRESS ON

SCREEN

REMOVE AFTER

INSTALLATION

PAIR

CIRCUIT POWER

AUTO

240V 30A 2-POLE RELAY

GPM-QP1R30240

MODULE INPUT:

INDOOR USE ONLY

#10-8 AWG Cu ONLY

HOME AUTOMATION EQUIP.

IC ID: 10798A-QP1R30240

FCC ID: PUU-QP1R30240

E523609

YYWW

120VAC 60Hz

240VAC 60Hz

240VAC 30A/2HP MAX

LOAD INPUT:

LOAD OUTPUT:

INPUT

OUTPUT

L2 L2

L1 L1

Multi-Page LCD screen that can display the following:

–Power draw at the output.

–Firmware, Mac Address, and Regulatory Info.

–UID of the Host the module is communicating with.

–Real-time Bluetooth status connectivity icon.

BManual Load Switch - Toggle to the ON position to switch the

load on. Toggle to AUTO for normal operation.

PAIR Button - The PAIR button is a multi-use button. The

duration that the button is pressed and held determines the

function that gets initiated:

Press and Release - Cycles through the various screens

available on the LCD (POWER > ENERGY > INFO 1 > INFO 2).

Press and hold - Press and hold for 2 seconds to put module

into pairing mode. Press and hold for 5 seconds to reset.

DInput Power Connections - Connect outputs from two

breakers to inputs L1 and L2 on the module. See the Wiring

section below.

EOutput Power Connections - Connect a 240V AC load across

outputs L1 and L2. See the Wiring section below.

F120V AC Connection - Plugs into the 120V AC bus bar in the

breaker panel. The voltage on this connection powers the

module.

Neutral - The model number of the module determines the

type of neutral connection on the module:

– Plug-On Neutral - Positioned on the bottom of the module

is a neutral clip that plugs directly onto the neutral bar.

– Pigtail Neutral - A neutral wire protrudes from the

module’s rear and gets wired to the neutral bar in the

breaker panel.

Supported Software

Savant OS da Vinci 10.2

Electrical and Safety Characteristics

Screw Tighten Torque 3.0 Nm

Wire Type Copper (Cu) only

Pollution Degree 2

Purpose of Control Operating Control, Smart Relay Control

Module or the equivalent

Software Class A

Impulse Voltage 2500V

Supported Load Types

Standard Conﬁguration Relay On/O type loads (home automation)

Standards

Wireless Bluetooth Low Energy (BLE)

–2.4 GHz radio frequency

Regulatory

Safety and Emissions

FCC Part 15 UL ICES 003

Contains FCC ID: PUU-QP1R30240

Contains IC: 10798A-QP1R30240

RoHS Compliant

Recommended Load Center Types

All QO™ compatible modules ﬁt into ¾ inch load centers.

Power

Input Power

(powers the module) 120V AC (+/- 10%) @ 60 Hz, 0.1A (max)

Input Power

(from feeder breaker) 120V AC per input - 30A (max)

Load Power 7200VA

(240VAC 30A resistive load / 2HP max)

Features of Automatic

Action Type 1.B action

Dimensions and Weights (net)

Height Length Depth Weight

Module

(QO)

1.45 in.

(3.68 cm)

4.97 in.

(12.63 cm)

2.60 in.

(6.61 cm)

.5 lbs

(.23 kg)

Shipping 1.71 in.

(4.34 cm)

7.50 in.

(19.05 cm)

4.30 in.

(10.92 cm)

1.0 lbs.

(.45 kg)

Environmental

Temperature 32° to 104° F (0° to 40° C)

Humidity 5% to 85% Relative Humidity (non-condensing)

Location Indoor Use Only

Features

–Control capability for loads up to 7200 VA (volt-ampere).

–All QO™ relay modules are compatible with Schneider Electric/

Square D™ QO™ load centers.

–Dynamic management of loads.

–Built-in energy monitoring; +/- .5% revenue grade accuracy / 1 sec

sample time.

–Communicates over the air using Bluetooth Low Energy (BLE)

technology.

–Manual load switch on the front panel can toggle power to the

output On and O.

–Color LCD display for easy identiﬁcation and load status.

Single 30 Amp Relay Companion Module (2-Pole, 240V AC)

Quick Reference and Installation Guide

Speciﬁcations

Box Contents Descriptions

(1) 240VAC (2 Pole) Relay Companion Module

–GPM-QP1R30240-21 QO™ w/Plug-on Neutral

–GPM-Q1R30240-21 QO™ w/Pigtail Neutral

(1) Product Information and Regulatory Insert (009-1950)

(1) Quick Reference and Installation Guide (this document)

Construction of Control

Open Type Independently mounted for ﬂush mounting

Single 30 Amp Relay Companion Module - QRG | 009-2112-00 2 of 4 45 Perseverance Way, Hyannis MA 02601

ELECTRIC SHOCK! The 120/240V AC, 60 Hz source poses an

electrical shock hazard that has the potential to cause serious

injury to installers and end users.

CAUTION! Risk of Electric Shock - More than one disconnect

switch may be required to de-energize the device before

servicing.

IMPORTANT! A licensed electrician is required to install any of

Savant’s Relay Companion Modules.

Installation into Breaker Panel

Important Information

–The breaker(s) feeding this module should not be larger than 30 amps.

–This relay module can handle loads up to 30 amps.

–To determine the number of breaker panel spaces needed, add the number of spaces required for the circuit breakers with the spaces needed

for the module.

• Each 2-pole circuit breaker requires two spaces.

• Each Companion Module requires two spaces.

–Savant recommends not connecting any mission critical loads such as medical devices to this relay module.

Wiring with Plug-on Neutral Wiring with Pigtail Neutral

240V AC

Plug-on

neutral bar

Neutral Bar

Breaker Panel

Companion Module

with Plug-on Neutral

NOTE: The companion module

connects to just one phase.

The 2-pole breaker connects

to both phases.

Phase A

Phase B

STANDARD

BREAKER

STANDARD

BREAKER

2-POLE BREAKER

INPUT OUTPUT

OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

240VAC 2-POLE

RELAY

Load 120V AC

IMPORTANT! When making connections, observe all general electrical best practices which includes the local wire sizing guideline codes.

See the Branch Circuit Minimum Size Conductors table above.

1. Remove power from the breaker panel by switching o the panel’s main breaker.

2. Position and install a 2-pole breaker into any two slots in the breaker panel. Press ﬁrmly until the breaker is fully seated onto the

appropriate bus bars.

3. Position and install the Companion Relay Module into any two empty slots in the breaker panel. Press ﬁrmly until fully seated onto

the appropriate bus bar. This module is typically installed alongside the 2-pole breaker installed in step 2.

4. Use the diagrams below and make the appropriate connections. The diagram on the left is for the modules that contain a plug-on

neutral clip. The diagram on the right is for modules that include a neutral wire.

HELPFUL! This relay module ﬁlls two slots in the breaker panel but connects to only one phase (120V AC). See diagram below.

Branch Circuit Minimum Size of Conductors

(General circuit wiring, Copper Conductors)

15A 20A 30A 40A 50A 60A

#14 AWG #12 AWG #10 AWG #8 AWG #6 AWG #4 AWG

NOTE: This wiring requirement was based on the National Electric Code

(NEC) (ANSI/NFPA70), Canadian Electric Code, Part 1 (CEC), and local

codes Minimum Size of Conductors.

240V AC

120V AC

Neutral Bar

Breaker Panel

Companion Module

with Pigtail Wire for

the Neutral

NOTE: The companion module

connects to just one phase.

The 2-pole breaker connects

to both phases.

Phase A

Phase B

STANDARD

BREAKER

STANDARD

BREAKER

2-POLE BREAKER

INPUT OUTPUT

OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

240VAC 2-POLE

RELAY

Load

Single 30 Amp Relay Companion Module - QRG | 009-2112-00 3 of 4 45 Perseverance Way, Hyannis MA 02601

Circuit Test Instructions

Use the instructions below to test the relay modules. The setup requires:

–30 Amp Relay Companion Module.

–Load with maximum amperage of 30A.

–Standard 2-pole, 30 amp circuit breaker.

–Breaker test panel. The type of module determines the type of breaker panel (plug-on neutral or not).

–120/240V AC source

120V AC

240V AC

Neutral Bar

Plug-on Neutral Bus Bar

240V AC

Load

INPUT OUTPUT

OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

240V 2-POLE RELAY

L2 L2

standard

2-pole breaker

30 30

The companion module connects

to only one phase. The 2-Pole

breaker connects to both phases

1. Plug the 240V AC 2-Pole Companion Module and 30 amp 2-pole feeder breaker into the circuit breaker test panel.

2. Connect the output from one of the breakers on the 2-pole

breaker to the L1 input on the module.

3. Connect the output from the remaining side of the 2-pole

breaker to the L2 input on the module.

4. Connect one side of a load to the L1 output on the module.

5. Connect the remaining side of the load to the L2 output on the

module.

6. Apply power to the breaker panel (not shown in diagram)

7. Toggle the 30 amp 2-pole breaker to On.

8. To test, toggle the CIRCUIT POWER switch to the ON position

and observe the load switches On. Toggle the CIRCUIT POWER

switches to AUTO and verify the load switches O.

IMPORTANT!

–The 2-pole breaker connects across both phases in the breaker panel. The module, however, attaches to only one phase. This is shown in

the image below.

–The GPM-QP1R30240-21 and GPM-Q1R30240-21 modules can accept up to a #10 AWG wire. See the Branch Circuit Minimum Size of

Conductors table on the previous page.

Additional Documentation

Further information is available in the documents listed below and can be accessed via the Savant Customer Community.

–Panel Bridge Controller with PoE (PBC-P1000) QRG

–Savant Panelized Lighting Deployment Guide.

Single 30 Amp Relay Companion Module - QRG | 009-2112-00 4 of 4 45 Perseverance Way, Hyannis MA 02601

Notes

Savant QP1R30240 Guide d'installation

Marque: Savant

Modèle: QP1R30240

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Savant QP1R30240 Installation guide

Savant QP1R30240 Guide d'installation

Savant QP1R30240 Guide d'installation

dans d''autres langues

Documents connexes